Академический Документы
Профессиональный Документы
Культура Документы
Contents Page
Training Area Setup with S7-300 ...................................................................................................... 2
Configuration of the S7-300 Training Unit ......................................................................................... 3
Addressing S7-300 Modules ............................................................................................................ 4
Training Area Setup with S7- 400 ..................................................................................................... 5
Configuration of the S7-400 Training Unit ......................................................................................... 6
The Simulator ................................................................................................................................... 7
The Conveyor Model ........................................................................................................................ 8
Complete Symbol List (1) ................................................................................................................. 9
Complete Symbol List (2) ................................................................................................................. 10
Complete Symbol List (3) ................................................................................................................. 11
(32 channel
I/O modules)
Addresses For the training unit with the CPU 315-2DP and for the S7-400 training unit, you
can set the starting addresses of the modules by parameter assignment
(freely).
Slot No. 1 2 4 5 6 7 8 9 10
Modules PS CPU SM SM SM SM SM SM SM
Address 0.0
Address 0.7
Address 1.0
Address 1.7
Slot Numbers The slot numbers in the rack of an S7-300™ simplify addressing in the
S7-300™ environment. The position of the module in the rack determines the
first address on a module.
Slot 3 Logically reserved for an interface module (IM) for multi-tier configurations using
expansion racks. Even if no IM is installed, it must be included for addressing
purposes.
You can physically reserve the slot (such as for installing an IM at a later date) if
you insert a DM370 dummy module.
Slots 4-11 Slot 4 is the first slot that can be used for I/O modules, communications
processors (CP) or function modules (FM).
Addressing examples:
• A DI module in slot 4 begins with the byte address 0 .
• The top LED of a DO module in slot 6 is called Q8.0 .
Note Four byte addresses are reserved for each slot. When 16-channel DI/DO
modules are used, two byte addresses are lost in every slot!
Slot No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
PS CPU DI DI DO DO AI
32 32 32 32 8
Design You can see the design of the S7-400 training unit in the slide above.
Addressing You have the default addresses, as shown in the slide above, as long as no
configuration or parameter settings have been made.
Potentiometers for
setting the
Digital Display analog vales
DI DO
.0 .......... .......... .0
.1 .......... .......... .1
.2 .......... .......... .2
.3 .......... .......... .3 V
.4 .......... .......... .4
.5 .......... .......... .5
.6 .......... .......... .6 -15V...+15V AI2 AO1 -15V...+15V
AI1 AO2
.7 .......... .......... .7
.0 .......... ..........
.0
.1 .......... ..........
.1 AI1 AI2
.2 .......... .......... V
.2
.3 .......... ..........
.3
.4 .......... ..........
.5 .......... ..........
.4
.5
0 8 1 5 AI1 AI2 AO1 AO2
.6 .......... ..........
.6
.7 .......... ..........
.7
Design Two cables connect the simulator to the S7-300™ or S7-400™ training unit. The
simulator is divided into the following three sections:
• Analog section with a voltmeter for displaying the values at analog channels
0 and 1 or the analog outputs 0 and 1. You use the selector switch to choose
the voltage value you want to monitor. There are two separate
potentiometers for setting the values for the analog inputs.
Addressing You use the following addresses to address the inputs and outputs in your user
program :
Switch / Pushb. IW 0
LEDs QW 4
Thumb. buttons IW 2
Digital display QW 6
K_RT (Q 8.5)
K_LT (Q 8.6)
Design The slide shows a diagram of the conveyor model with its sensors and
actuators.
Addresses S7-300
Sensor / Actuator Symbol
(DI32,
DO32)
I 8.0 Light Barrier LB 1 LB1
I 8.1 Ackn. Pushbutton Bay 1 T_Bay_1
I 8.2 Ackn. Pushbutton Bay 2 T_Bay_2
I 8.3 Ackn. Pushbutton Bay 3 T_Bay_3
I 8.4 Ackn. PB Final Assembly T_Bay_4
I 8.5 Prox. switch Bay 1 (INI1) BAY_1
I 8.6 Prox. switch Bay 2 (INI2) BAY_2
I 8.7 Prox. switch Bay 3 (INI3) BAY_3