0 оценок0% нашли этот документ полезным (0 голосов)
46 просмотров7 страниц
The document discusses electronic circuit analysis and contains 50 multiple choice questions related to topics like amplifiers, op-amps, feedback, oscillators, power supplies, and transistor configurations. It tests knowledge of concepts such as gain, input and output characteristics, coupling methods, stability criteria, distortion sources, and packaging of integrated circuits.
The document discusses electronic circuit analysis and contains 50 multiple choice questions related to topics like amplifiers, op-amps, feedback, oscillators, power supplies, and transistor configurations. It tests knowledge of concepts such as gain, input and output characteristics, coupling methods, stability criteria, distortion sources, and packaging of integrated circuits.
The document discusses electronic circuit analysis and contains 50 multiple choice questions related to topics like amplifiers, op-amps, feedback, oscillators, power supplies, and transistor configurations. It tests knowledge of concepts such as gain, input and output characteristics, coupling methods, stability criteria, distortion sources, and packaging of integrated circuits.
2. The gain of an amplifier with feedback is given by which of
the following relations?
A / (1 - αA) (Your Correct Answer)
3. Ideal op-amp requires no input current, but real op-amp
needs a very small input current called input bias current. At both inputs, the bias currents have a slight difference. What do you call this difference?
input offset current (Correct Answer)
4. The non-inverting and inverting inputs of an op-amp have
an input voltage of 1.5 mV and 1.0 mV, respectively. If the op- amp has a common-mode voltage gain of 10 and a differential- mode gain of 10,000, what is its output voltage?
5.0125 V (Correct Answer)
5. AF amplifier can amplify frequencies in the range:
15 Hz to 15 kHz (Correct Answer)
6. For sustaining oscillations in a feedback amplifier, the loop
gain should be:
greater than one (Your Correct Answer)
7. By using which of the following methods the frequency
stability in an oscillator can be achieved?
By incorporating a tuned circuit (Your Correct Answer)
8. A 20-Vdc power supply was found to have a ripple voltage of 2 Vrms when supplying 1.5 amps load. Calculate its percent ripple.
10.00% (Correct Answer)
9. Calculate the closed-loop voltage gain of an inverting
amplifier having a feedback and an input resistance of 100 k? and 10 k?, respectively.
10 (Correct Answer)
10. A good op-amp has a:
very high input resistance (Correct Answer)
11. The crystal oscillator frequency is very stable due to
______ of the crystal.
high Q (Correct Answer)
12. An amplifier of class AB means its output signal is between
the output of class B and A, such that it varies from 180?(class B) to 360?(class A). How about its efficiency?
It is always as efficient as class A (25%). (Your Correct
Answer)
13. What do we mean by internally compensated op-amps?
Op-amps with internal frequency compensation capacitor
to prevent oscillation. (Correct Answer)
14. The output offset voltage of an op-amp is (are) due to:
input offset current and input offset voltage are correct
(Correct Answer) 15. Op-amp parameter(s) that is important in large signal dc- amplification.
slew rate (Correct Answer)
16. Low frequency response of amplifier is mainly limited by
______ capacitor.
bypass (Correct Answer)
17. In most voltage regulators, what is used as a voltage
reference element?
zener diode (Correct Answer)
18. For high density ICs involving many op-amps, what
packaging is suitable?
SMT (Correct Answer)
19. Which class of amplifiers that is intended for pulse
operation?
class D (Correct Answer)
20. The load resistance in voltage amplifiers:
should be as large as possible (Your Correct Answer)
21. A multivibrator having two stable state:
bistable (Your Correct Answer)
22. A circuit usually containing two transistors or tubes in an
RC-coupled amplifier, the two active devices switch each other alternately on and off.
Multivibrator (Correct Answer)
23. The fundamental requirement for oscillations in an amplifier is:
positive feedback from output to input (Correct Answer)
24. ______ contributes to harmonics distortion in amplifiers.
Non-linearity in active device (Correct Answer)
25. How can we minimize the effect of the input offset current and input offset voltage at the output offset voltage?
by making the feedback resistance small (Correct
Answer)
26. The magnitude of the op-amps input offset voltage before
it can be classified as a low-input offset voltage op-amp.
0.2 mV (Correct Answer)
27. ________ is a major characteristics of an IC:
size (Your Correct Answer)
28. In amplifiers the main source of harmonic distortion is:
non-linearity in active device (Correct Answer)
29. In case of audio amplifiers which of the following
distortions is least objectionable?
Phase distortion (Correct Answer)
30. The transistor configuration used at the output
complementary stage of most op-amps:
common collector (Correct Answer)
31. The maximum output voltage rate of change of an op- amp.
slew rate (Correct Answer)
32. Where does the Q-point of a class C amplifier is
positioned?
below cutoff region (Correct Answer)
33. What cause(s) the well-adjusted output offset voltage of
op-amps to change?
change in operating temperature
component aging variations in supply voltage all of these (Correct Answer)
34. An amplifier basically constructed from two transistors and
whose output is proportional to the difference between the voltages applied to its two inputs.
differential amplifier (Correct Answer)
35. For a power supply with a peak-to-peak ripple voltage of 5
Vpp, determine its rms ripple.
1.44 Vrms (Correct Answer)
36. The ______ oscillator uses tapped capacitors in the tuned
circuit.
Colpitts (Correct Answer)
37. A load draws 1 A current from a 10-V regulated power
supply. Calculate the power dissipated by the regulator if it has an input voltage of 16 V
6 Watts (Your Correct Answer)
38. The signal handling capacity of an amplifier will be high when the operating point is selected.
in the middle of the active region (Correct Answer)
39. Calculate the dc-voltage at the output of a half-wave
rectifier with a 12Vrms input.
5.4 V (Correct Answer)
40. The distributed amplifier utilizes ______ to increase
bandwidth.
transmission lines (Correct Answer)
41. A Class-B push-pull amplifier suffers from distortion which
is:
crossover (Correct Answer)
42. An amplifier has the following percent harmonic
distortions; D2=10%, D3=5% and D4=1%. What is the amplifier %THD?
11.22% (Your Correct Answer)
43. Calculate the peak-to-peak ripple voltage of a 20 V full-
wave power supply with a filter capacitor C = 220 uF, when delivering a load current of 50 mA.
2.0 Vpp (Correct Answer)
44. Dual-in-line or DIL package is designated as:
TO-116 (Correct Answer)
45. The frequency at which the open-loop gain of an op-amp is
0.707 times its value at very low frequency: break frequency (Your Correct Answer)
46. The output of a class-B amplifier:
consists of positive half-cycles only (Your Correct
Answer)
47. Basically, which class of amplifiers has the least distortion?
class A (Correct Answer)
48. A modified version of UPS, wherein the power-line itself is
used as a backup to the system.
standby power supply (Correct Answer)
49. When one input of the op-amp is connected to ground and
the other is to the signal source, its operation is called:
single-ended input (Correct Answer)
50. Transistor arrangement that operates like a darlington but
uses a combination of pnp and npn transistors instead of both npn.