Академический Документы
Профессиональный Документы
Культура Документы
0.60 m x 1.000 m
1.050 m
1.00 m 1.200 m
0.10 m 0.100 m
0.60 m Drain Base Width (Clear) 0.60 m
Drain Height (Clear) 1.00 m
Wall Thickness 0.10 m
Base Thickness 0.10 m
0.100 m Top Slab Thickness 0.10 m
0.800 m
0.350 m 0.350 m
0.700 m
Grade of Concrete = M 20
Allowable Bending Stress scbc = 6.67 MPa (Table 9 IRC 21-2000)
Grade of steel = Fe 415
Allowable stress in Steel = 200 MPa (Table 10 IRC 21-2000)
Modular Ratio m = 10 (Note 1Table 9 IRC 21-2000)
n Neutral Axis depth factor = 0.250
j Leverarm factor = 0.917
Q Moment of Resistance factor = = 0.76 MPa
1 LOAD CALCULATION
1) Dead load
Wall
UDL of Vertical Walls 0.1 x 2.5 = in t/sq. m = = 0.25
Height of wall = 1.10 m
Weight of wall = 0.275 t/m
Base slab
UDL of Base Slab = 0.1 x 2.5 = 0.25
Length of slab = 0.80 m
Load = 0.20 t/m
0.050 m 0.050 m
0.700 m 1.050 m
0.28 t 0.28 t
0.000 t 0.000 t
0.25 t/m
2) Earth Pressure
1
sin( - ) sin( )
settlement = 40 mm
2
Spring constant = 375.0 t/m per m width
No of Springs to be provided = 10 Nos
spring constant at end supports = 9.375 t/m depth per m width
spring constant at intermediate supports (adjacent to end support) = 25.446 t/m depth per m width
spring constant at intermediate supports = 32.143 t/m depth per m width
0.000
0.617 t
0.53 m 1.050 m
0.59m
0.44 m
DL+SIDL
STAAD PLANE FRAME ANALYSIS FOR DRAIN OF SIZE 0.7 X 1.05
UNITS MTONS METERS
JOINT COORDINATES
1 0.00 0.00 0.00
2 0.700 0.00 0.00
4 0.00 1.050 0.00
3 0.700 1.050 0.00
5 0.050 0.00 0.00
6 0.650 0.00 0.00
7 0.700 0.050 0.00
8 0.00 0.050 0.00
9 0.136 0.00 0.00
10 0.221 0.00 0.00
11 0.307 0.00 0.00
12 0.393 0.00 0.00
13 0.479 0.00 0.00
14 0.564 0.00 0.00
MEMBER INCIDENCES
148
281
315
459
5 9 10
6 10 11
7 11 12
8 12 13
9 13 14
10 14 6
11 6 2
12 7 2
13 3 7
MEMBER PROPERTIES
3 11 PRIS YD 0.1 ZD 1.0
4 to 10 PRIS YD 0.1 ZD 1.0
1 13 PRIS YD 0.1 ZD 1.0
2 12 PRIS YD 0.1 ZD 1.0
CONSTANTS
E CONCRETE ALL
POISSON CONCRETE ALL
SUPPORTS
1 2 FIXED BUT FX FZ MX MY MZ KFY 9.375
5 6 FIXED BUT FX FZ MX MY MZ KFY 25.446
9 TO 14 FIXED BUT FX FZ MX MY MZ KFY 32.143
LOAD 1 DEAD LOADS
MEMBER LOADS
3 TO 11 UNI GY -0.250
3 CONC GY -0.000 0.050
11 CONC GY -0.000 0.000
1 13 CONC GY -0.275
LOAD 2 EARTH PRESSURES
MEMBER LOADS
1 TRAP GX 0 0.560
2 TRAP GX 0.560 0.588
13 TRAP GX 0 -0.56
12 TRAP GX -0.56 -0.588
1 TO 2 UNI GX 0.588
12 TO 13 UNI GX -0.588
LOAD COMB 3 LOAD COMBINATION
1 1.0 2 1.0
PERFORM ANALYSIS
PRINT ANALYSIS RESULTS
PRINT FORCE ENVELOPE NS 10
FINISH
2 ANALYSIS RESULTS
3 DESIGN OF DRAIN
Design constants
Grade of Concrete = M 20
Allowable Bending Stress (scbc) = 6.67 MPa
Grade of steel = Fe 415
Allowable stress in Steel = 200 MPa
modular Ratio (m) = 10
Neutral Axis depth factor (h) = 0.250
Leverarm factor (j) = 0.917
Moment of Resistance factor (Q) = 0.76 MPa
Total moment on base slab due to Moment-tm Shear-t MAX Moment with impact-tm
DL+Earth pressures 0.08 0.01
Net maximum moment on base slab = 0.08 t-m Clear Cover = 50.0 mm
Hence, Effective Depth required = 31.5 mm
Total Depth Provided = 100 mm
Effective Cover = 55 mm
Hence, Effective Depth provided = 45 mm > Required, Hence, OK
Area of steel to be provided = 92.12 mm²
Minimum area of steel = 0.12% = 120.00 mm²
Provide TOR 10 dia @ 200 mm c/c 393 mm² Percent = 0.87 %
Shear check
Max. SF = 0.01 t
Shear Stress = 0.003MPa
For this percentage of steel, the allowable shear stress from table 11B of Amendments to IRC:21-1987
= 0.51 Mpa
> Actual, Hence OK