Академический Документы
Профессиональный Документы
Культура Документы
G 4303
Foreword
This standard is based on the provisions of Article 12, paragraph 1 which is applied mutatis
mutandis pursuant to Article 14 of the Industrial Standardization Act. (JSSA) / The Japan
Standards Association (JSA) has proposed that the Japanese Industrial Standards should
be amended with the draft Industrial Standards. After the deliberation of the Japan Industrial
Standards Research Committee, the Japanese Industrial Standards revised by the Minister
of Economy, Trade and Industry.
Note that this description has no effect on the validity, scope, etc. of the patent right shown
above.
The owner of the above-mentioned patent right is not a discriminatory and reasonable
condition against the Japan Industrial Standards Committee.
Guarantee that they are willing to license the patent right.
A part of this standard is a patent having a technical property, a patent application after
publication, a utility model right, or
It warns that there is a possibility of conflict with the utility model registration application.
Minister of Economy, Trade and Industry and Japan Industrial Standards Survey
Is a patent having such technical properties, a patent application after publication, a utility
model right, or a utility new after application publication
There is no responsibility for the confirmation regarding the application for proposal
registration.
Table of contents
page
1. Scope of application………………………………………………………………………………………………………………..
2. Cited standard…………………………………………………………………………………………………………………………
3. Kind of symbol…………………………………………………………………………………………………………………………
4. Chemical composition……………………………………………………………………………………………………………..
4.1 Molten steel analysis value………………………………………………………………………………………………………
5. Product analysis value……………………………………………………………………………………………………………..
6. Corrosion resistance…………………………………………………………………………………………………………………..
9. appearance………………………………………………………………………………………………………………………………..
11.Heat treatment…………………………………………………………………………………………………………………………
12. Test………………………………………………………………………………………………………………………………………….
13. Inspection………………………………………………………………………………………………………………………………..
14. Display……………………………………………………………………………………………………………………………………..
15. Report……………………………………………………………………………………………………………………………………..
2. Standards cited The standards listed in Appendix 1 constitute part of the requirements of this
standard by being cited in this standard. Do. These cited standards apply to the latest version
(including the supplements).
3. Types of symbols There are 61 types of bars, and the types of symbols and classifications are
according to 1.
SUS 890L
Remarks-B is added to the end of the type symbol if it is necessary to represent the symbol with a
symbol.I will add it.
SUS 304-B
4. Chemical composition
4.1 Molten steel analysis value bar is subjected to the test of 12.1, and its molten steel analysis value
Is from 2 to 6.
4.2 Product analysis value When the order requests product analysis, the test is performed
according to 12.1, and the value is a value of 2 to 6Apply the allowable fluctuation value in
accordance with 5 of JIS G 0321. However, the allowance of elements not specified in JIS G 0321 For
variable values, it is based on the agreement between delivery and receiving parties.
3 G 4303:2005
Remarks 1. Except for SUS 447J1 and SUS XM 27, Ni may be contained at 0.60% less than.
2. SUS 447J1 and SUS XM 27 may contain up to 0.50% Ni, up to 0.20% Cu and up to 0.50% (Ni + Cu).
4 G 4303:2005
Table :- 5 Chemical composition of martensitic system (cont.)
Unit %
Kind of
C Si Mn P S Ni Cr Mo Pb
symbol
1.00 less 1.00 less 0.040 less 0.030 less
SUS 420J2 0.26~0.40 (2) 12.00~14.00 - -
than than than than
1.00 less 1.25 less 0.060 less 0.15 less
SUS 420F 0.26~0.40 (2) 12.00~14.00 (1) -
than than than than
1.00 less 1.00 less 0.040 less 0.030 less
SUS 420F2 0.26~0.40 (2) 12.00~14.00 - 0.05~0.30
than than than than
0.20 less 1.00 less 1.00 less 0.040 less 0.030 less
SUS 431 1.25~2.50 15.00~17.00 - -
than than than than than
1.00 less 1.00 less 0.040 less 0.030 less
SUS 440A 0.60~0.75 (2) 16.00~18.00 (3) -
than than than than
1.00 less 1.00 less 0.040 less 0.030 less
SUS 440B 0.75~0.95 (2) 16.00~18.00 (3) -
than than than than
0.95~ 1.00 less 1.00 less 0.040 less 0.030 less
SUS 440C (2) 16.00~18.00 (3) -
1.20 than than than than
0.95~ 1.00 less 1.25 less 0.060 less 0.15 less
SUS 440F (2) 16.00~18.00 (3) -
1.20 than than than than
(1) Mo may contain up to 0.60%.
(2) Ni may contain 0.60% less than.
(3) Mo may contain 0.75% less than.
5.1 Mechanical properties of austenitic system The mechanical properties of austenitic system are
in accordance with 7. In this case, test
The material is in accordance with Class A of JIS G 0404. However, proofreading applies particularly when
there is an orderer's designation.
Table:- 7 Mechanical properties of austenite system
Unit%
Hardness (5)
Kind of Strength N / Tensile strength N / Aperture
Growth % HRBS Or
symbol mm2 mm2 (4) % HBW HV
HRBW
241 253
275 more 45 more 100 less
SUS 201 520 more than 40 more than less less
than than than
than than
207 218
275 more 45 more
SUS 202 520 more than 40 more than less 95 less than less
than than
than than
207 218
205 more 60 more
SUS 301 520 more than 40 more than less 95 less than less
than than
than than
187 200
205 more 60 more
SUS 302 520 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 50 more
SUS 303 520 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 50 more
SUS 303 Se 520 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 50 more
SUS 303 Cu 520 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 60 more
SUS 304 520 more than 40 more than less 90 less than less
than than
than than
187 200
175 more 60 more
SUS 304 L 480 more than 40 more than less 90 less than less
than than
than than
217 220
275 more 50 more
SUS 304N1 550 more than 35 more than less 95 less than less
than than
than than
250 260
345 more 50 more 100 less
SUS 304N2 690 more than 35 more than less less
than than than
than than
217 220
245 more 50 more
SUS 304LN 550 more than 40 more than less 95 less than less
than than
than than
187 200
175 more 60 more
SUS 304J3 480 more than 40 more than less 90 less than less
than than
than than
187 200
175 more 60 more
SUS 305 480 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 60 more
SUS 309S 520 more than 40 more than less 90 less than less
than than
than than
187 200
205 more 50 more
SUS 310S 520 more than 40 more than less 90 less than less
than than
than than
223 230
300 more 40 more
SUS 312L 650 more than 35 more than less 96 less than less
than than
than than
187 200
205 more 60 more
SUS 316 520 more than 40 more than less 90 less than less
than than
than than
187 200
175 more 60 more
SUS 316L 480 more than 40 more than less 90 less than less
than than
than than
217 220
275 more 50 more
SUS 316N 550 more than 35 more than less 95 less than less
than than
than than
217 220
245 more 50 more
SUS 316LN 550 more than 40 more than less 95 less than less
than than
than than
187 200
205 more 50 more
SUS 316Ti 520 more than 40 more than less 90 less than less
than than
than than
NOTE:- 1. The value of 7 applies to bars with a diameter, side, opposite side or thickness of 180 mm less
than.
The value in the case of more than 180 mm depends on the agreement between the delivery
parties.
2. In the report of measured HRB, specify HRBS or HRBW.
3. 1N / mm2= 1 MPa
5.2 Mechanical properties of austenite-ferrite systems The mechanical properties of austenite-ferrite systems
are 8 by. In this case, the test material is as per Class A of JIS G 0404. However, bearing capacity is particularly
specified by the orderer.
Apply
(4) Not applicable to flat steel. However, if there is a designation of the order, it is based on the agreement
between the delivery parties.
Remarks :- 1. The value of 8 applies to bars with a diameter, side, opposite side or thickness not exceeding 75
mm.The value for more than 75 mm depends on the agreement between the delivery and
receiving parties.
2. 1N / mm2 = 1 MPa
5.2 Mechanical properties of ferrites The mechanical properties of ferrites are as per 9. In this case, the test
material is JIS
According to A of G 0404 However, proofreading applies particularly when there is a designation of the
orderer.
Tensile
Kind of Strength N Aperture Hardness
strength N / Growth %
symbol / mm2 (4) % (5) HBW
mm2
Tensile
Kind of Strength N Aperture Hardness
strength N / Growth %
symbol / mm2 (4) % (5) HBW
mm2
(4) Not applicable to flat steel. However, if there is a designation of the order, delivery matters
Agreement between the two parties.
Remarks :-
1. The value of 9 applies to bars of diameter, side, opposite side or thickness less than 75 mm.The value
for more than 75 mm depends on the agreement between the delivery and receiving parties.
2. When the orderer specifies Charpy impact test, 2 mm U of JIS Z 2242Perform using a notch test piece.
Where 2 mm U-notch specimens can not be collected Agreement on the applicable test pieces and
impact by.
3. 1N/mm2 =1MPa
5.2 Mechanical properties of martensitic system The mechanical properties of martensitic system are as
follows.
(a) The mechanical properties of quenched and tempered rods are as in 10. In this case, the test material is
Class A of JIS G 0404, Or according to JIS G 0404 Class B.
(b) The hardness of the annealed bar shall be in accordance with 11. In this case, the test material is as per
Class A of JIS G 0404. The However, the hardness of the bar when annealed at about 750 ° C depends on
the agreement between the delivery and receiving parties.
(4) Not applicable to flat steel. However, if there is a designation of the orderer, it is based on the agreement
between the delivery parties.
Ramarks:- 1. The value of 10 applies to bars of diameter, side or opposite side or thickness 75 mm less than.
Values beyond 75 mm are subject to the agreement between the delivery and receiving parties
2. The Charpy impact value applies to bars of dimensions that allow the removal of 2 mm U-notch
specimens according to JIS Z 2242. 2 mm U
If a notch test piece can not be collected, the applicable test piece and impact value shall be in
accordance with the agreement between the delivering and receiving parties.
3. 1N/mm2 =1MPa
(4) Not applicable to flat steel. However, if there is a designation of the orderer, it is based on the agreement
between the delivery parties.
(5) The hardness of SUS630 shall be one of them.
Remarks :-
1 The value of 12 applies to bars with a diameter, side, opposite side or thickness not exceeding 75 mm. The
value in the case of more than 75 mm depends on the agreement between the delivery parties.
2. The mechanical properties of SUS 630 which has been subjected to heat treatment other than those listed
in Annex 5 shall be in accordance with the agreement between the delivering and receiving parties.
3. 1N/mm2=1MPa
6. Corrosion Resistance Regarding the corrosion resistance by the intergranular corrosion test, especially when
there is a specification of the order, 12.3 between the delivery parties. The test methods applied from the
above shall be agreed upon and tested, and the corrosion resistance shall be in accordance with the
agreement between the delivering and receiving parties.
7. Shape and dimensional tolerance The shape and dimensional tolerance shall be as follows.
(a) The standard dimensions for hot-formed round steel and hexagonal steel are to 13.
Table :- 13 Standard dimensions for hot-formed round and hexagonal steels
Unit mm
Side distance of
Diameter of round steel
hexagonal steel
9 19 35 55 110 12 30
10 20 36 60 120 14 32
11 22 38 65 130 17 35
12 24 40 70 140 19 38
13 25 42 75 150 21 41
14 26 44 80 160 23 46
15 28 45 85 170 24
16 30 46 90 180 26
17 32 48 95 190 27
18 34 50 100 200 29
(b) The dimensional tolerance and diameter difference or deviation of the diameter, side or opposite side
distance of the hot-formed round, square and hexagonal steel According to 14
Remarks :- Those exceeding 150 mm are subject to the agreement between delivery parties.
Remarks :- Those exceeding 150 mm are subject to the agreement between delivery and receiving parties.
(e) The bending tolerance of the bar shall be 3 mm or less per unit length (m), and for the total length,
[3 mm × length (m) / m] or less Let down.
(f) The dimensional tolerances of the forging bars are in accordance with the agreement between the
delivery parties.
(g) The dimensional tolerance of the cutting material for round bars is 18.
Remarks :- The values for dimensions 15 mm or less and over 400 mm are According to the agreement
between delivery parties.
Effective number
Basic mass (kg / cm2 m) × cross-
Unit mass kg / m Three digit
sectional area (cm2)
numberTo round.
Effective number
1 mass kg Unit mass (kg / m) × length (m) Three digit
numberTo round.
9. Appearance The surface of the rod is well-finished and has defects such as harmful flaws and cracks
that cause problems in normal use. It should not be.
10. Manufacturing method The manufacturer shall manufacture with an appropriate manufacturing
method that meets the required quality. order
The manufacturer shall report the method of manufacture if required by the manufacturer.
In addition, if there is an agreement on the manufacturing method at the time of the contract between
the delivering and receiving parties, follow it.
11. Heat treatment The bar heat treatment at the time of delivery shall be prescribed in 7 to 12 by the
manufacturer unless there is an agreement between the delivering and receiving parties.
The heat treatment conditions must be selected to meet the required quality. Typical heat treatment
conditions are listed in Annex 1 Shown in ~ 5.
Black skin produced by heat treatment is removed by an appropriate method such as pickling and
cutting if necessary.
The heat treatment symbol representing the heat treatment method is shown in Appendix Table 2.
12. Examination
12.1.1 General items of analytical test and how to take analytical samples According to 8 (Chemical
constituents) of JIS G 0404. Order is product analysis
The method of taking a sample when request is required is in accordance with JIS G 0321 Section 4
(Analytical sampling method).
12.1.2 Analysis method The method of molten steel analysis shall be in accordance with JIS G 0320. The
method of product analysis is in accordance with JIS G 0321.
12.2.1 General test general items of mechanical test shall be in accordance with JIS G 0404.
12.2.2 How to select the test material Take one sample for the same molten steel and the same heat
treatment condition.
12.2.3 Number of test pieces The number of test pieces shall be from 1 test piece to 1 test piece.
12.2.4 Test specimens Tensile test specimens, impact test specimens and hardness test specimens shall
be as follows.
(a) The tensile test specimen is any one of JIS Z 2201 No. 10 test specimen, 13 B test specimen, 14 A test
specimen or 14 B test specimen Use
(b) For impact test pieces, use JIS Z 2242 2 mm U notch test pieces. However, the 2 mm U notch
specimen is
If this is not the case, the parties concerned may agree on the dimensions and shape of the test piece to
be applied.
(c) For the hardness test piece, a part of the tensile test piece can be used.
12.2.5 Test method The tensile test, impact test and hardness test shall be as follows.
(a) The tensile test method shall be in accordance with JIS Z 2241. However, the test temperature is 23 ±
5 ° C and the measurement of tensile strength is
In such a case, use a tensile rate such that the rate of strain increase in the parallel part of the test
specimen is 40 to 80% / min.
(b) The impact test method shall be in accordance with JIS Z 2242. However, the test temperature is 23
± 2 ° C.
(c) The hardness test method shall be as follows. However, the test temperature is 23 ± 5 ° C.
12.3.1 How to select the test material Take one sample for the same molten steel and the same heat
treatment condition.
12.3.2 Number of test pieces The number of test pieces shall be from 1 test piece to 1 test piece.
12.3.3 Test method The test method shall be one of the following.
(c) Mechanical properties shall conform to 5). However, depending on the agreement between the
deliveries and
14. Indications For bars that pass the inspection, the following items shall be indicated for each rod.
However, diameter, side, opposite side distance or thickness
A bar with a diameter of 30 mm or less may be bound and displayed in bundles. However, depending on
the agreement between the delivery
(b) Dimensions
(c) Heat treatment code (for martensite and precipitation hardening systems) (7)
15. Reporting The manufacturer may, at the request of the orderer, report on the test results of
prescribed or designated tests, and dimensions, quantities, and receipts.
A report must be submitted to the orderer stating the status of entry. The report also includes electronic
media such as electronic transmission.
However, the type of inspection document shall be JIS G 0415 paragraph 1 of 2.3 (delivery test report)
or 3.1.B (inspection certificate).
If alloying elements are added according to notes 2 to 5, add the contents of the additional elements to
the score sheet..
JIS G 0321 Product analysis method for steel and its allowable fluctuation value
JIS G 0572 test method of Sulfuric acid and ferric sulfate corrosion stainless steel
JIS G 0573 65% nitric acid corrosion test method for for stainless steel
JIS G 0575 test method for Sulfuric acid and copper sulfate corrosion for stainless steel
The heat treatment temperature of the bar is shown below for reference.
1. Heat treatment temperatures The heat treatment temperatures of stainless steel are shown in Tables
1 to 5 in Annex.
Remark :- For SUS 316Ti, SUS 321 and SUS 347, the order is stabilized heat treatment Can be
specified. The heat treatment temperature in this case is 850 to 930 ° C. Ru.