Академический Документы
Профессиональный Документы
Культура Документы
GSM_WCDMA Cell
Reselection and CS
Handover Feature Guide
GERAN UR15
ZGO-02-03-002 GSM_WCDMA Cell Reselection and CS Handover Feature Guide
TABLE OF CONTENTS
2 Overview ............................................................................................................ 4
2.1 Feature Introduction ............................................................................................. 4
2.2 License Control .................................................................................................... 5
2.3 Correlation with Other Features ........................................................................... 5
4 Parameters......................................................................................................... 9
7 Abbreviation .................................................................................................... 92
8 Reference Document....................................................................................... 93
FIGURES
TABLES
1 Feature Attribute
BSC Version: [ZXUR 9000 GSM (V6.50.31)]
Attribute: [Optional]
BTS -
BSC √
iTC -
MSC √
MGW -
SGSN -
GGSN -
HLR -
2 Overview
CS handover
1. Required Features
ZGO-02-02-013 Different Cell Reselection Parameters for IDLE and ACTIVE Status
None
3. Affected Features
None
3 Technical Description
This feature enables basic interworking between the GSM and WCDMA networks,
including CS handover, reselection in idle mode and PS reselection in connected mode
from GSM to WCDMA, which is defined in 3GPP specifications. ZTE GSM produces
support the functions mentioned above.
1. When the BSC receives the measurement report including the WCDMA neighboring
cells, the sliding window method is used to process the Received Signal Code Power
(RSCP) or the ratio of Energy Chip and Noise (Ec/No) value.
2. The BSC defines the threshold for every WCDMA neighboring cell, which is the
inter-RAT handover threshold plus the offset value. The thresholds of RSCP and
Ec/No are set separately. When at least P out of N values are greater than the
threshold, a CS handover to the WCDMA network is triggered.
3. If more than one WCDMA neighboring cell satisfies the inter-RAT handover
conditions, only the neighboring cell with the best RSCP or Ec/No value is selected,
because the inter-RAT handover attempt only occurs once.
Directed retry is a special application of the CS handover. When the voice service is
active, the BSC triggers directed retry to the WCDMA network because the MS fails to
apply for a TCH or SDCCH in the GSM network. Inter-RAT directed retry is triggered
when P out of N RSCP or Ec/No values are equal to or greater than the inter-RAT
directed retry threshold plus the offset value. If more than one WCDMA neighboring cell
satisfies the inter-RAT directed retry conditions, only the neighboring cell with the best
RSCP or Ec/No value is selected, because the inter-RAT directed retry attempt only
occurs once.
When the CS handover from GSM to WCDMA fails, the BSC sets the penalty timer for
this WCDMA neighboring cell to prevent an immediate handover again. In the penalty
time, the BSC cannot trigger an inter-RAT handover to this cell even if all the conditions
are satisfied, which means that this WCDMA neighboring cell should be deleted from the
target cell list.
1. The BSC sends system information SI 2quater and SI 2ter to the MS through the
BCCH or extended BCCH, which describes the WCDMA neighboring cell list,
search conditions, and reselection parameters.
2. When a WCDMA neighboring cell satisfies the search conditions, the MS decodes
and measures the Common Pilot Channel (CPICH) of the WCDMA neighboring cell
in accordance with Qsearch_I (Qsearch_I ≠ 15) to obtain CPICH RSCP or CPICH
Ec/No.
3. The MS should update the value of Received Level Average (RLA_C) for the
serving cell and the strongest (at least six) non-serving GSM cells at least every 5s.
4. The MS should reselect a suitable WCDMA cell if the following criteria are all met
for a period of 5s:
i. RSCP ≥ RLA_C (s). That is, the RSCP value of the neighboring cell is greater
than the RLA_C value for the serving cell.
ii. RSCP ≥ FDD_Qoffset + RLA_C (n). That is, the RSCP value of the
neighboring cell is greater than the RLA_C value for all of the suitable
non-serving GSM cells plus the FDD_Qoffset value. If cell reselection occurs
before 15s, FDD_Qoffset needs to be added by 5dB to prevent ping-pong
re-selection.
iii. Ec/No ≥ FDD_Qmin - FDD_Qmin_Offset. That is, the Ec/No value of the
neighboring cell is equal to or greater than the FDD_Qmin-FDD_Qmin_Offset
value.
iv. RSCP ≥ FDD_RSCP_threshold. That is, the RSCP value of the neighboring
cell is equal to or greater than FDD_RSCP_threshold.
If more than one WCDMA cell meets the above conditions, the cell with the best RSCP
value is selected.
The PS cell reselection procedure in connected mode from GSM to WCDMA is described
as follows:
1. When the WCDMA neighboring cell satisfies the search conditions, the MS decodes
and measures the CPICH of the WCDMA neighboring cell in accordance with
Qsearch_P (Qsearch_P ≠ 15) to obtain CPICH RSCP or CPICH Ec/No.
2. The MS should update the RLA_P value for the serving cell and the strongest (at
least six) non-serving GSM cells at least every 5s.
3. The MS should reselect a suitable WCDMA cell if the following criteria are all met
for a period of 5s:
i. RSCP ≥ RLA_P (s). That is, the RSCP value of the neighboring cell is greater
than the RLA_P value for the serving cell.
ii. RSCP ≥ FDD_Qoffset + RLA_P (n). That is, the RSCP value of the
neighboring cell is greater than the RLA_P value for all of the suitable
non-serving GSM cells plus the FDD_Qoffset value. If cell reselection occurs
before 15s, FDD_Qoffset needs to be added by 5dB to prevent ping-pong
re-selection.
iii. Ec/No ≥ FDD_Qmin - FDD_Qmin_Offset. That is, the Ec/No value of the
neighboring cell is equal to or greater than the FDD_Qmin-FDD_Qmin_Offset
value.
iv. RSCP ≥ FDD_RSCP_threshold. That is, the RSCP value of the neighboring
cell is equal to or greater than FDD_RSCP_threshold.
If more than one WCDMA cells meet the above conditions, the cell with the best RSCP
value is selected.
4 Parameters
inform asking a UE to
ation report its
from UtranClassmark
UE information after the
UE is handed over
from the 3G
network to the 2G
network. During a
2G-to-3G
handover, it is
possible that the
handover request
message does not
contain the
UtranClassmark
information of the
UE or contains
improper
UtranClassmark
information. This
may lead to failures
when the UE is
handed over from
the 2G network to
the 3G network
later due to
incorrect
UtranClassmark
information.
If this parameter is
set to "1 (Yes)",
after the UE is
handed over to the
BSC from an
external network,
the BSC initiates a
classmark request,
asking the UE to
report its
UtranClassmark
information.
This parameter
indicates the T3121
timer, which
indicates the
protection time after
the BSC sends an
Inter-System to
UTRAN Handover
Command (UM)
message to an MS.
This timer is started
when the BSC
Hando
sends an
ver
Inter-System to
protect
UTRAN Handover
BSS ing
Command 100
Function timer 1..650 100 100
message to an MS. ms
Timer to
This timer is
WCD
stopped when the
MA/FD
BSC receives a
D
CLEAR
COMMAND
message from the
MSC (normally
when the handover
is completed) or a
HANDOVER
FAILURE message
from the MS.
When the timer
expires, the BSC
sends a CLEAR
REQUEST
message to the
MSC with the cause
CAUSE_RI_MSG_
FAIL (radio
interface message
failure).
This parameter
indicates the CELL
ID (CI) of a UTRAN
External
FDD cell. To
UTRAN
distinguish each
FDD
CI cell in GSM PLMN 0..65535 N/A 0 0
Cell
uniquely, the
Configur
network operator
ation
allocates a unique
ID for each cell in a
location area.
MCC consists of
External three digits of
UTRAN decimal number. It
FDD is used to uniquely
MCC 0..999 N/A 0 0
Cell identify the home
Configur country of the
ation mobile user (or
system).
MNC consists of
three digits of
External
decimal number. It
UTRAN
uniquely identifies a
FDD
MNC specific PLMN 0..999 N/A 0 0
Cell
network in a
Configur
country
ation
(determined by
MCC).
10562..1083
8,9662..9938
,1162..1513,
External
1537..1738,4
UTRAN UTRA This parameter
357..4458,43
FDD N cell means the
87..4413,223 N/A 0 0
Cell freque frequency range of
7..2563,2937
Configur ncy UTRAN FDD cells.
..3088,9237..
ation
9387,3112..3
388,3712..38
12,412,437,4
62,487,512,5
37,562,587,6
12,637,662,6
87,1887,191
2,1937,1962,
1987,2012,2
037,2062,20
87,1007,101
2,1032,1037,
1062,1087,1
037,1062,25
87,2612,263
7,2662,2687,
2712,2737,2
762,2787,28
12,2837,286
2,2887,2912,
3412,3437,3
462,3487,35
12,3537,356
2,3587,3612,
3637,3662,3
687
External
UTRAN This parameter
Scram
FDD indicates the
bling 0..511,65535 N/A 0 0
Cell scrambling of
code
Configur UTRAN FDD cells.
ation
RAC is a
composition part of
Routing Area
Identity (RAI). RAI
defines the GPRS
serving cell
identification.
GPRS system
divides the location
area (LAs) to
several routing
areas (RAs) using
RAI
(MCC+MNC+LAC+
RAC).
Routing Area (RA)
External
distribution, similar
UTRAN
to GSM system,
FDD
RAC uses the location 0..255 N/A 0 0
Cell
area to manage a
Configur
group of cells. MS
ation
initiates “Routing
area update”
procedure in cell
reselection mode if
new RAI differs
from old RAI during
cell reselection.
SGSN knows the
routing area
information of the
MS in the standby
status. Then, when
the network has
packet data or
circuit data to
transmit, it will page
the MS in that
routing area. RAI
cannot span more
than one SGSN.
This parameter is
consistent with the
data at CN side.
wheth
er an
External
extern
UTRAN Whether an
al 3G
FDD external 3G cell is 0: No
cell is N/A 0 0
Cell included in GSM 1: Yes
include
Configur system.
d in
ation
GSM
system
This parameter
indicates the report
priority of a
neighbor cell.
Neighbor cells are
reported in
accordance with the
following priority
Adjacen CS
order:
t GSM adjace
Neighbor cells with 0:low
Cell nt cell N/A 0 0
the same frequency 1:high
Configur report
band as the serving
ation priority
cell. These cells
must meet the
following
requirements: The
BSIC is valid. The
measured field
strength ranks high
among the cells
GSM900M), the
neighbor cells with
higher RepPrioCS
have the higher
report priority.
Among neighbor
cells with the same
RepPrioCS, the
cells with the
greater sum of
RprtThoCSXXX (or
XXXRprtThoCS)
and
RprtOffsetCSXXX
(or
XXXRprtOffsetCS)
have the higher
report priority.
This parameter
indicates the
UTRAN adjacent
Adjacen
cell to which the
t UTRA 0: Handover
handover and
UTRAN N and reselect
reselection are N/A 0 0
Cell Relatio 1: Reselect
performed, only
Configur n type 2: Handover
reselection is
ation
performed, or only
handover is
performed.
This parameter
Adjacen
DN of indicates the
t
UTRA referenced DN of
UTRAN
N FDD the UTRAN FDD N/A N/A N/A N/A
Cell
source source cell,
Configur
cell meaning the
ation
UTRAN FDD
{RelationTyp
This parameter
Adjacen UTRA e==1}[1..64],
indicates a
t N {RelationTyp
sequence number
UTRAN Relatio e==2}[65..12
that uniquely N/A N/A N/A
Cell n 8],
identifies a UTRAN
Configur Seque {RelationTyp
neighbor cell of the
ation nce e==0}[129..1
local cell.
92]
Handover from
GSM to UTRAN
being triggered only
indicates that
UTRAN adjacent
cell satisfies the
minimum
requirement for
RSCP normal UE
Adjacen offset communication
t hando within it.
UTRAN ver to This parameter is a
0..63 N/A 5 5
Cell UTRA prerequisite to
Configur N ensure enough field
ation adjace intensity for
nt cell uplink/downlink of
UTRAN adjacent
cells. It also
controls the priority
of a UE to handover
to different adjacent
cells.
When the adjacent
cell is the cell to
Handover from
GSM to UTRAN
being triggered only
indicates that
UTRAN adjacent
cell satisfies the
minimum
requirement for
normal UE
communication
Ec/No within it.
Adjacen offset This parameter is a
t hando prerequisite to
UTRAN ver to ensure enough field
0..49 N/A 5 5
Cell UTRA intensity for
Configur N uplink/downlink of
ation adjace UTRAN adjacent
nt cell cells. It also
controls the priority
of a UE to handover
to different adjacent
cells.
When the adjacent
cell is the cell to
which the handover
and reselection are
performed, set this
parameter.
they will be
transformed to
adjacent cells in the
next priority. Cells
with access
technologies (such
as UTRAN/FDD),
with high
RepPrioCS, and a
frequency band
(such as
GSM900M) takes
priority). For cells
with the same
RepPrioCS, the
large cell and the
cell of
RprtThoCSXXX (or
XXXRprtThoCS)
and
RprtOffsetCSXXX
(or
XXXRprtOffsetCS)
take the priority.
This parameter
indicates the
threshold for the
target cell traffic. It
Adjacen
Target determines whether
t
cell to perform
UTRAN
traffic handover to this 0..100 % 75 75
Cell
thresh cell. If the target cell
Configur
old traffic is higher than
ation
this threshold, then
the handover is not
performed to this
cell.
This parameter is
used for UTRAN
handover and
selecting adjacent
cells.
Adjacen
the
t This parameter
priority
UTRAN indicates the priority
of 0..7 N/A 1 1
Cell of UTRAN neighbor
Utran
Configur cells.
Cell
ation
The parameter is
Adjacen used to indicate
t Is the whether the
UTRAN directe neighbor cell is the 0: No
N/A 1 1
Cell d retry directed retry cell. It 1: Yes
Configur ncell is one of the
ation neighbor cell
parameters.
0: Not allow
Requir to send
e UE "UTRAN
to class mark
send change"
This parameter
UTRA message
indicates whether a
UTRAN N 1: Both
UE is required to
Measur class- ECSC and N/A 0 0
send UTRAN
ement mark UE control
classmark change
chang whether the
message early.
e UE sends
messa "UTRAN
ge classmark
early change"
message
0: Broadcast
on normal
Chann
BCCH block
el
This parameter 1: Broadcast
locatio
UTRAN indicates channel on extended
n of
Measur location of BCCH block , N/A 0 0
si2qua
ement SI2quater AGCH_BLO
ter
broadcast. CK
broadc
reservation
ast
value will be
1
CS
It indicates 0: enhanced
measu
enhanced measuremen
UTRAN rement
measurement t report
Measur type N/A 1 1
report for UE or 1: normal
ement reporte
measurement measuremen
d by
report message. t report
UE
This parameter
CS defines the number
numbe of adjacent cells
r of with the same
same frequency band as
UTRAN
freque the serving cell,
Measur 0..3 N/A 2 2
ncy which are included
ement
adjace in the measurement
nt cells report or the
in strongest cell list
report (measurement data
in a terminal).
This parameter is
used to reselect the
UTRAN adjacent
cell if the following
requirements are
satisfied:
Received signal
code power (RSCP)
of this adjacent cell
is higher than
average receiving
level RLA_C of this
FDD
UTRAN cell.
resele
Measur RSCP of the 0..15 N/A 0 0
ction
ement adjacent cell is
offset
higher than RLA_C
of all adjacent GSM
cells by at least
FDD_Qoffset (FDD
reselection offset)
for more than 5
seconds.
FDD_Qoffset of the
cell increases by 5
dB if the cell is
reselected 15
seconds earlier.
Ec/No (code-noise
ratio) of this
adjacent cell is
larger than or equal
to designated
FDD_Qmin
(minimum value of
code-noise ratio of
UTRAN reselected
cell).
If more than one
UTRAN cell meets
above conditions,
then select the cell
which has the
largest RSCP.
This parameter
indicates the
minimum value of
Min Ec/No of the 0: -20dB
Ec/No UTRAN cell when it 1: -6dB
of reselects adjacent 2: -18dB
UTRAN
UTRA cell. The value of 3: -8dB
Measur N/A 7 7
N Ec/No of the 4: -16dB
ement
resele UTRAN cell should 5: -10dB
cting be larger than the 6: -14dB
cell value defined by 7: -12dB
this parameter in
order to reselect the
adjacent cell.
h_c
before
UE
receivi
ng
qsearc
h_C
This parameter
defines a threshold.
If the average
received signal
level RLA_C of the
Thresh
local cell is lower
old
than this threshold
when
(meaning the
UE
parameter value is
UTRAN perfor
0-6) or higher than
Measur ms 0..15 N/A 15 15
the threshold
ement search
(meaning the
under
parameter value is
dedica
8-14), the UE starts
ted
searching for 3G
mode
adjacent cells. The
parameter value 7
means "always"
and 15 means
"never".
CS 0:RSCP,
class receiving
of power of
It indicates whether
UTRAN reporte CPICH
an MS uses RSCP
Measur d scramble of N/A 1 1
or Ec/No to report
ement quantit UTRAN cell
measurement.
ies of at UE, the
UTRA unit is dBm
N 1:Ec/No,
This parameter
indicates the
maximum number
of UTRAN/FDD
adjacent cells
Max
included in a packet
numbe
measurement
r of
report or list of
UTRA
strongest cells
N/FDD
UTRAN (measurement data
adjace
Measur in a terminal). If 0..3 N/A 2 2
nt cells
ement UTRAN/FDD
in
adjacent cells are
measu
not full in a report,
rement
the vacancies are
report(
used for GSM
CS)
adjacent cells (if
the TDD technology
is supported, the
vacancies are used
for TDD cells).
GPRS MEASUREMENT
UTRA ORDER or
N PACKET CELL
cell_0/ CHANGE ORDER
Measu message. When the
rement signal level is lower
thresh than threshold 0 - 7
old of (corresponding to -
UE 98, - 94, …, - 74
perfor dBm), or greater
ming_ than threshold 8 -
1 15 (- 78, - 74, …,-
GPRS 54 dBm), the
UTRA system searches
N cell for 3G cells. The
threshold 7
indicates always
search and 15
indicates never
search.
This parameter
defines the
minimum offset with
FDD which the RSCP of
GPRS the reselected 3G
resele FDD adjacent cell
ction shall be higher than
UTRAN offset_ the RLA_P of the
Measur 0/FDD serving cell and 0..15 N/A [8,8] [8,8]
ement GPRS other suitable GSM
resele adjacent cell. A
ction one-dimensional
offset_ array is used to
1 represent packet
idle state parameter
and packet
transmission state
parameter. To
enable a UE to
reselect a 3G
adjacent cell, the
following conditions
must be met for at
least 5 seconds:
CPICH Ec/No > =
FDD_ Qmin –
FDD_Qmin_Offset
CPICH RSCP >
RLA_P(s+n) +
_FDD_GPRS_Qoff
set
CPICH RSCP > =
FDD_RSCP_Thres
hold The
parameters
FDD_GPRS_Qoffs
et, FDD_Qmin, and
FDD_Qmin_Offsett
are broadcast to the
UE in the packet
system message
PSI3quater.
RLA_P(s+n)
defines the average
value of the signal
strengths of the
serving cell and n
strongest GSM
neighbor cells.
FDD_RSCP_Thres
hold =
FDD_RSCPmin –
min((P_MAX – 21
dBm), 3 dB) if
FDD_RSCPmin is
broadcast in the
serving cell system
message;
otherwise,
FDD_RSCP_Thres
hold = Qrxlevmin +
Pcompensation +
10 dB 0 indicates
that the 3G FDD
adjacent cell is
always selected.
1 = -28 dB;
2 = -24 dB;
…
15 = 28 dB
This parameter
defines the
PS
minimum value with
MIN
which the Ec/No of
Ec/No
the reselected 3G
of
adjacent cell shall
UTRA
be higher than or
N 0: -20dB
equal to the current
resele 1: -6dB
cell. A
cting 2: -18dB
UTRAN one-dimensional
cell_0/ 3: -8dB
Measur array is used to N/A [7,7] [7,7]
PS 4: -16dB
ement represent packet
MIN 5: -10dB
idle state parameter
Ec/No 6: -14dB
and packet
of 7: -12dB
transmission state
UTRA
parameter. To
N
enable a UE to
resele
reselect a 3G
cting
adjacent cell, the
cell_1
following conditions
must be met for at
least 5 seconds:
CPICH Ec/No > =
FDD_ Qmin –
FDD_Qmin_Offset
CPICH RSCP >
RLA_P(s+n) +
_FDD_GPRS_Qoff
set
CPICH RSCP > =
FDD_RSCP_Thres
hold The
parameters
FDD_GPRS_Qoffs
et, FDD_Qmin, and
FDD_Qmin_Offset
are broadcast to the
UE in the packet
system message
PSI3quater.
RLA_P(s+n)
defines the average
value of the signal
strengths of the
serving cell and n
strongest GSM
neighbor cells.
FDD_RSCP_Thres
hold =
FDD_RSCPmin –
min((P_MAX – 21
dBm), 3 dB) if
FDD_RSCPmin is
broadcast in the
serving cell system
message;
otherwise,
FDD_RSCP_Thres
hold = Qrxlevmin +
Pcompensation +
10 dB
0= -20dB, 1= -6dB,
2= -18dB, 3= -8dB,
4= -16dB, 5=
-10dB, 6= -14dB,
7= -12dB.
A one-dimensional
array is used to
represent packet
idle state parameter
and packet
transmission state
parameter. To
enable a UE to
reselect a 3G
adjacent cell, the
FDD_ following conditions
QminP must be met for at
S least 5 seconds:
UTRAN Offset CPICH Ec/No > =
Measur _0/FD FDD_ Qmin – 0..7 N/A [0,0] [0,0]
ement D_Qmi FDD_Qmin_Offset
nPS CPICH RSCP >
Offset RLA_P(s+n) +
_1 _FDD_GPRS_Qoff
set
CPICH RSCP > =
FDD_RSCP_Thres
hold The
parameters
FDD_GPRS_Qoffs
et, FDD_Qmin, and
FDD_Qmin_Offset
are broadcast to the
UE in the packet
system message
PSI3quater.
RLA_P(s+n)
defines the average
value of the signal
strengths of the
serving cell and n
strongest GSM
neighbor cells.
FDD_RSCP_Thres
hold =
FDD_RSCPmin –
min((P_MAX – 21
dBm), 3 dB) if
FDD_RSCPmin is
broadcast in the
serving cell system
message;
otherwise,
FDD_RSCP_Thres
hold = Qrxlevmin +
Pcompensation +
10 dB
0 = 0 dB, 1 = 2 dB,
2 = 4 dB, 3 = 6 dB,
4 = 8 dB, 5 = 10 dB,
6 = 12 dB, 7 = 14
dB.
PS This parameter
MIN defines the
RSCP minimum RSCP
UTRAN of threshold for a
Measur UTRA UTRAN FDD cell to 0..15 N/A [6,6] [6,6]
ement N be reselected. It is
resele broadcast to UEs in
cting the packet system
cell_0/ message
PS PSI3quater. A
MIN one-dimensional
RSCP array is used to
of represent packet
UTRA idle state parameter
N and packet
resele transmission state
cting parameter.
cell_1 To enable a UE to
reselect a 3G
adjacent cell, the
following conditions
must be met for at
least 5 seconds:
CPICH Ec/No > =
FDD_ Qmin –
FDD_Qmin_Offset
CPICH RSCP >
RLA_P(s+n) +
_FDD_GPRS_Qoff
set
CPICH RSCP > =
FDD_RSCP_Thres
hold The
parameters
DD_GPRS_Qoffset
, FDD_Qmin, and
FDD_Qmin_Offset
are broadcast to the
UE in the packet
system message
PSI3quater.
RLA_P(s+n)
defines the average
value of the signal
strengths of the
serving cell and n
strongest GSM
neighbor cells.
FDD_RSCP_Thres
hold =
FDD_RSCPmin –
min((P_MAX – 21
dBm), 3 dB) if
FDD_RSCPmin is
broadcast in the
serving cell system
message;
otherwise,
FDD_RSCP_Thres
hold = Qrxlevmin +
Pcompensation +
10 dB
0 = -114 dBm, 1 =
-112 dBm, 2 = -110
dBm, 3 = -108 dBm,
4 = -106 dBm, 5 =
-104 dBm, 6 = -102
dBm, 7 = -100 dBm,
8 = -98 dBm, 9 =
-96 dBm, 10 = -94
dBm, 11 = -92 dBm,
12 = -90 dBm, 13 =
-88 dBm, 14 =-86
dBm, 15 = -84 dBm.
Note: The
parameters in the
formula are all
GPRS parameters,
that is, the
FDD_RSCPmin is
FDD_RSCPminPS.
NCC in BSIC of
some GSM cells
are allowed, but
BCC is invalid (that
is, the radio system
CS
does not have
measu
adjacent cells
rement
UTRAN corresponding to
reporti 0: Normal
Measur BCC). N/A 0 0
ng rate 1: Lower
ement This parameter
of
indicates whether
adjace
the system allows
nt cell
UE to report field
intensity of such
cells (NCC is
allowed but BCC us
invalid).
NCC in BSIC of
some GSM cells
are allowed, but
BCC is invalid (that
is, the radio system
CS UE does not have
report adjacent cells
UTRAN invalid corresponding to 0: not
Measur cell BCC). allowed N/A 0 0
ement level This parameter 1: allowed
allowe indicates whether
d the system allows
UE to report field
intensity of such
cells (NCC is
allowed but BCC us
invalid).
This parameter is to
control the number
UTRAN MulBn
of reports of 0: No
Measur dRprtC N/A 0 0
different adjacent 1: Yes
ement S
cells except the
serving cell.
This parameter
indicates the offset
CS
to be added when
offset
UE reports signal
which
field strength. If the
is
UTRAN actual field strength 0: 0 dB
added
Measur of a GSM adjacent 1: 10 dB N/A 0 0
when
ement cell is only n dBm, 2: Automatic
UE
the UE maps n+
reports
ScaleOrdCS to the
rxlev
value that n shall
value
map to when
mapping to
RXLEV(0…63).
This is applicable
only when the
"enhanced
measurement
report" message is
used.
If the signal
strength of the
adjacent cell
exceeds -48 dBm,
the system can use
this parameter to
report the actual
value and the UE
reports the SCALE
value in the
"enhanced
measurement
report" message. If
SCALE_ORD=2,
the UE uses a value
that is just sufficient
for reporting the cell
with the strongest
signal level.
GSM9
00M
Adjace
UTRAN nt cell An offset can be
Measur reporti added to a 900 M 0..7 N/A 0 0
ement ng GSM adjacent cell.
signal
level
Offset
GSM1
800M
Adjace
UTRAN nt cell An offset can be
Measur reporti added to a 1800 M 0..7 N/A 0 0
ement ng GSM adjacent cell.
signal
level
Offset
ng than or equal to
signal RprtThoCS1800
level (dimensionless,
Thresh corresponding to
old RXLEV portion in
measurement
report, different
mapping
relationship for
different RXLEV).
As to whether it can
be reported in
certain period, it
also depends on
signal level,
RepPrioPS,
MulBndRprtPS and
RprtOffsetPS900.
GSM1
900M
Adjace
UTRAN nt cell An offset can be
Measur reporti added to a 1900 M 0..7 N/A 0 0
ement ng GSM adjacent cell.
signal
level
Offset
UTRA
N/FDD An offset can be
Adjace added to an FDD
UTRAN nt cell adjacent cell when
Measur reporti the priority 0..7 N/A 0 0
ement ng sequence of the
signal hand-in adjacent
level cells is determined.
Offset
When reporting to
UTRAN/FDD
UTRA
adjacent cells, only
N/FDD
when signal level in
Adjace
the cell is higher
nt cell
UTRAN than or equal to
reporti
Measur FDDRprtThoCS 0..7 N/A 0 0
ng
ement (dimensionless,
signal
corresponding to
level
RXLEV portion in
Thresh
measurement
old
report, different
mapping
relationship for
different RXLEV), it
can be reported. As
to whether it can be
reported in certain
period, it also
depends on signal
level, RepPrioCS,
FDDMulRatRrptCS
and
FDDRprtOffsetCS.
CS UE
This parameter
search
indicates whether to
UTRA
allow UE to search
N
UTRAN adjacent
adjace
cells in the frame
UTRAN nt cell 0: not
where BSIC
Measur in allowed N/A 0 0
decoding is
ement BSIC 1: allowed
needed. If allowed,
decodi
UE can use at most
ng
25 frames for
frame
search in 13
indicati
seconds.
on
GSM8
50M
Adjace
UTRAN nt cell An offset can be
Measur reporti added to a 850 M 0..7 N/A 0 0
ement ng GSM adjacent cell.
signal
level
Offset
This parameter is
used to indicate
whether an MS
uses the PACKET
PS
MEASUREMENT
measu
REPORT or
UTRAN rement
PACKET
Measur type 0..1 N/A 0 0
ENHANCED
ement reporte
MEASUREMENT
d by
REPORT
UE
messages for (NC)
reporting. It is
reported to the MS
in the PACKET
CELL CHANGE
ORDER or
PACKET
MEASUREMENT
ORDER message.
0: If each frequency
point in the BA
(GPRS) list is
configured with at
least one BSIC,
PACKET
ENHANCED
MEASUREMENT
REPORT is used to
report
measurement
result; otherwise,
PACKET
MEASUREMENT
REPORT is used.
1: PACKET
MEASUREMENT
REPORT is used to
report
measurement
result.
PS
numbe
The number of cells
r of
from the GSM
same
UTRAN serving frequency
freque
Measur band that shall be 0..3 N/A 2 2
ncy
ement included in the
adjace
measurement
nt cells
report.
in
report
PS
class
of
reporte Indicates the
UTRAN d reporting quantity
Measur quantit for UTRAN FDD 0..1 N/A 0 0
ement ies of cells.0 = RSCP, 1 =
UTRA Ec/No
N
adjace
nt cells
Max
numbe
The number of cells
r of
from the access
UTRA
technology/mode
N/FDD
UTRAN FDD (one or more)
adjace
Measur that shall be 0..3 N/A 2 2
nt cells
ement included in the list
in
of strongest cells or
measu
in the measurement
rement
report.
report(
PS)
PS
measu Indicates the
rement allowed reporting
UTRAN
reporti rate.0 = normal, 1 =
Measur 0..1 N/A 0 0
ng rate reduced.
ement
of Default value =
adjace normal.
nt cell
PS UE Indicates if GSM
UTRAN report cells with invalid
0: No
Measur invalid BSIC and allowed N/A 0 0
1: Yes
ement cell NCC part may be
level reported.0 Report
MS in
single-frequency
GSM system needs
only to report
contents of six
adjacent cells with
the strongest
signals in a
frequency band,
when reporting the
PS
survey result of
multi-b
UTRAN adjacent cells to the
and
Measur network. 0..3 N/A 0 0
report
ement In multi-band
indicati
networking, MS can
on
enter with priority
into a specific
frequency band
during handover.
The MS reports the
survey result
according to the
signal intensity and
the frequency band
of the signals,
according to the
actual situation.
PS multiband report
indication is used to
notify MS to report
contents of
adjacent cells in
multiple frequency
bands. It is one of
the system control
parameters.
The setting of this
parameter is
subject to traffic in
each frequency
band.
General principles
to set the
parameters are as
follows: 0: If the
traffic of each
frequency band is
almost equivalent,
and the operator
has no choice over
the frequency band.
3: If the traffic of
each frequency
band is quite
different, and the
operator hopes that
MS enters a
specific frequency
band with priority.
This parameter
SCALE_ORD
indicates the offset
used for the
reported RXLEV
values in the
PACKET
ENHANCED
MEASUREMENT
REPORT message.
The signal level
shall be mapped to
an RXLEV value
PS between 0 and 63,
offset as follows:
which RXLEV 0 = less
is than 110 dBm +
UTRAN added SCALE.
Measur when RXLEV 1 = 110 0..2 N/A 0 0
ement UE dBm + SCALE to
reports 109 dBm + SCALE.
RXLE RXLEV 2 = 109
V dBm + SCALE to
value 108 dBm + SCALE.
:
:
RXLEV 62 = 49
dBm + SCALE to
48 dBm + SCALE.
RXLEV 63 =
greater than 48
dBm + SCALE.
where, SCALE is
defined by the
SCALE_ORD
parameter in the
PACKET CELL
CHANGE ORDER
and PACKET
MEASUREMENT
ORDER messages.
The MS indicates
the SCALE value to
be used in the
PACKET
ENHANCED
MEASUREMENT
REPORT message.
If the actual field
strength of a GSM
adjacent cell is only
n dBm, the UE
maps n+
SCALE_ORD to the
value that n shall
map to when
mapping to
RXLEV(0…63).
This is applicable
only when the
PACKET
ENHANCED
MEASUREMENT
REPORT message
is used.
If the signal
strength of the
adjacent cell
exceeds -48 dBm,
the system can use
this parameter to
report the actual
value and the UE
reports the SCALE
value in the
PACKET
ENHANCED
MEASUREMENT
REPORT message.
If SCALE_ORD=2,
the UE uses a
minimum offset,
which is sufficient
for reporting the cell
with the strongest
signal level.
Apply en offset to
the reported value
GSM when prioritizing the
UTRAN
900 cells for reporting
Measur 0..7 dB 0 0
Offset( for GSM frequency
ement
PS) band 900.0, 6, … ,
42 dB Default value
= 0 dB.
Apply priority
reporting if the
GSM reported value is
UTRAN 900 above threshold for
Measur Thresh GSM frequency 0..7 N/A 0 0
ement old(PS band 900.0, 6, … ,
) 36, (never).
Default value =
always.
Apply en offset to
the reported value
GSM
UTRAN when prioritizing the
1800
Measur cells for reporting 0..7 dB 0 0
Offset(
ement for GSM frequency
PS)
band 1800.0, 6, … ,
42 dB Default value
= 0 dB.
Apply priority
reporting if the
GSM reported value is
UTRAN 1800 above threshold for
Measur Thresh GSM frequency 0..7 N/A 0 0
ement old(PS band 1800.0, 6, … ,
) 36, (never).
Default value =
always.
Apply en offset to
the reported value
GSM when prioritizing the
UTRAN
1900 cells for reporting
Measur 0..7 dB 0 0
Offset( for GSM frequency
ement
PS) band 1900.0, 6, … ,
42 dB Default value
= 0 dB.
Apply priority
reporting if the
GSM reported value is
UTRAN 1900 above threshold for
Measur Thresh GSM frequency 0..7 N/A 0 0
ement old(PS band 1900.0, 6, … ,
) 36, (never).
Default value =
always.
This parameter
indicates the offset
for the reported
UTRAN UTRA
value when UTRAN
Measur N/FDD 0..7 dB 0 0
FDD sorts cells. It is
ement Offset
sent to MSs in the
PACKET
MEASUREMENT
ORDER or
PACKET CELL
CHANGE ORDER
message over
PACCH. When the
system reports
UTRAN/FDD
neighbor cells, if
there are two cells
with signals greater
than or equal to
FDDRprtThoPS
and the RepPrioPS
values are the
same, then the cell
whose sum value of
signal level and
FDDRprtOffsetPS
is greater is
reported in priority.
This parameter
indicates the
UTRAN FDD
measurement
report threshold.
It is broadcast to
MSs in the PACCH
UTRA
UTRAN PACKET
N/FDD
Measur MEASUREMENT 0..7 N/A 0 0
Thresh
ement ORDER or
old
PACKET CELL
CHANGE ORDER
message over
PACCH. When
reporting to
UTRAN/FDD
adjacent cells, only
This parameter
indicates whether
PS UE
UEs are allowed to
search
search for UTRAN
UTRA
neighbor cells when
N
BSIC decoding is
adjace
required. If UTRAN
UTRAN nt cell
neighbor cell 0: No
Measur in N/A 0 0
search is allowed, a 1: Yes
ement basic
UE can use a
decodi
maximum of 25
ng
frames to search for
frame
UTRAN neighbor
indicati
cells within 13
on
seconds.
This parameter is
This parameter
specifies an offset
for sorting GSM
850 M neighbor
cells to be reported.
It is sent to MSs
through a PACKET
MEASUREMENT
ORDER or
PACKET CELL
CHANGE ORDER
GSM message on
UTRAN
850 PACCH.
Measur 0..7 dB 0 0
Offset( If the signal levels
ement
PS) of two GSM 850 M
neighbor cells are
equal to or greater
than
RprtThoPS850, and
their RprtThoPS850
values are equal,
the cell with the
greater sum of
signal level and
RprtOffsetPS850 is
reported first.
This parameter
indicates a
threshold for
reporting GSM 850
M neighbor cells. It
is sent to MSs
through a PACKET
MEASUREMENT
ORDER or
PACKET CELL
CHANGE ORDER
message on
PACCH.
A GSM 850 M
neighbor cell can
be reported only
GSM when the signal
UTRAN 850 level in the cell is
Measur Thresh equal to or greater 0..7 N/A 0 0
ement old(PS than
) RprtThoPS850.
The signal level (no
dimension)
corresponds to the
RXLEV part in a
measurement
report.
Different RXLEV
values have
different mapping
relationships.
Whether the GSM
850 M neighbor cell
is reported in a
specific period
depends on the
signal level,
RepPrioPS,
MulBndRprtPS, and
RprtOffsetPS850.
A
minim
um
thresh
old of The RSCP of -102
UTRAN
RSCP dBm is enough for
Measur 0..15 dBm 6 6
for UEs to operate
ement
UTRA stably in FDD.
N FDD
cell
re-sele
ction
Applie
s an FDD_Qmincan
UTRAN offset indicates the Ec/No
Measur to requirement for the 0..7 dB 0 0
ement FDD_ reselection to FDD
Qmin neighbor cells.
value
Signal
strengt
h and
UTRAN Signal strength and
load
Measur load and capacity 0..2 N/A 0 0
and
ement priority
capacit
y
priority
This parameter
determines the
UTRAN Load
threshold of
Measur thresh 0..100 % 60 60
maximum access
ement old
load for the 3G cell
that is reselected to
the 3G adjacent
cell. If the load is
lower than this
threshold, the value
is acceptable.
This parameter
determines the
threshold of
remaining access
Availa
capacity for the 3G
ble
UTRAN cell that is
capacit
Measur reselected to the 1..100 % 40 40
y
ement 3G adjacent cell. If
thresh
the remaining
old
access capacity is
higher than this
threshold, the value
is acceptable.
This parameter
indicates whether
Inter intersystem
UTRAN system handover within
Handov hando BSC is allowed. 0: No
N/A 0 0
er ver The parameter 1: Yes
Control suppor determines whether
ted BSC can issue
handover to 3G
system.
Punish
ment This parameter
UTRAN period defines a protection
Handov of period to prevent an
1..255 N/A 7 7
er UTRA immediate
Control N cell handover after a
when handover failure.
hando
ver
failure
In GSM system,
BSC uses the
power level
measurement data
to manage and
control handover
decisions. BSC
uses average
values instead of
Slipper
original values of
y
measurement data
windo
for handover
w size
decisions.
for
It helps prevent
calcula
UTRAN negative impact on
ting
Handov network
Ec/No 1..31 N/A 6 6
er performance
or
Control caused by abrupt
RSCP
changes in
averag
measurement data.
e
Average on
value
measurement value
to be
in UTRAN adjacent
zero
cell also shall be
required.
HoWindowUTRAN
of Ec/No or RSCP
average is the
window size to
calculate Ec/No or
RSCP average in
adjacent UTRAN
According to GSM
specifications, MS
can report to BSS
the
measurement data
of at most six
adjacent cells with
strongest signal
strength. Thus the
measurement
results might not be
consecutive. For
cells whose signal
Numb
strength is less than
er that
-110 dBm, the
UTRAN measu
measurement data
Handov rement
are not reported. 0..31 N/A 1 1
er value
To avoid the
Control allowe
negative impact of
d to be
0 on averaging,
zero
suppose occasional
0 is allowed and is
not used in
averaging, but
excessive
occurrences of 0
indicate that the
signals of this
adjacent cell are
too poor.
If the number of
zeroes in used for
average calculation
exceeds Number of
zero allowed in AV,
then measurement
average equals to
sum of reported
values divided by
Neighboring cell .
To be specific,
during averaging, if
the count of 0s in
the sampling count
exceeds
“ZeroAllowed”,
these sampling
values are hardly
reliable, and the
measurement
average will be the
sum of the reported
values divided by
NCellWindow. If the
count of 0s in the
reported values
does not exceed
“ZeroAllowed”,
these sampling
values are much
reliable and the
measurement
average will be the
sum of the reported
values divided by
(NCellWindow - the
count of 0s).
This parameter
determines if allow
directed retry to
UTRAN cell. When
no service channel
Directe
is allocated in this
d retry
UTRAN cell, a user can try
to
Handov to redirect to 0: No
UTRA N/A 0 0
er adjacent cell under 1: Yes
N cell
Control allowed case by
allowe
corresponding
d
function switch. If
this parameter is
configured as Yes,
it can be redirected
to 3G adjacent cell.
This parameter
indicates the priority
control of FDD/TDD
handover.
When FDD
adjacent cells and
TDD adjacent cells
UTRAN FDD/T 0: Priority to
exist together, to
Handov DD FDD
control the selection N/A 0 0
er hando 1: Priority to
sequence of a
Control ver TDD
target cell,
FDDTDDPrio
parameter to show
whether to prefer to
FDD cell handover
or to TDD cell
handover.
This parameter
describes UTRAN
handover priority
control. MSC sends
the Service
Handover
parameter to BSC 0:Handover
through the to UTRAN
“ASSIGNMENT first
REQUEST” and 1:Not
“HANDOVER Handover to
REQUEST” UTRAN first
messages. 2:Not allow to
Service Handover Handover to
parameter has UTRAN
three values, 3:According
including prefer to to MSC,
UTRAN UTRA
UTRAN handover, default
Handov N
not prefer to handover to N/A 3 3
er hando
UTRAN handover, UTRAN first
Control ver
disallow to UTRAN 4:According
handover, taking to MSC,
actions on default not
handover decision handover to
on subsequent UTRAN first
BSC. 5:According
ServiceHo can be to MSC,
configured as the default not
Default Value used allowed to
while MSC does not handover to
deliver the Service UTRAN
Handover
parameter, or
configured as BSC
forcedly using the
mode set by
ServiceHo, but not
the Service
Handover
parameter
delivered by MSC.
Hando HoRSCP_P_FDD
ver of
UTRAN
from HoRSCP_N_FDD
Handov
GSM RSCP average 1..20 N/A 4 4
er
to values are not
Control
UTRA lower than the sum
N FDD of
RSCP HoRSCP_THS_FD
Value D and
N HoRSCPOffsetUTR
AN, the PS
handover from
GSM to UTRAN
can be triggered.
HoRSCP_P_FDD
of
Hando HoRSCP_N_FDD
ver RSCP average
from values are not
UTRAN GSM lower than the sum
Handov to of
1..20 N/A 3 3
er UTRA HoRSCP_THS_FD
Control N FDD D and
RSCP HoRSCPOffsetUTR
Value AN, the PS
P handover from
GSM to UTRAN
can be triggered.
BSC reserves at
least
HoEcNo_N_FDD
Hando
RSCP average
ver
values for a UTRAN
from
adjacent cell. When
UTRAN GSM
at least
Handov to
HoEcNo_P_FDD 0..49 N/A 25 25
er UTRA
out of the latest
Control N FDD
HoEcNo_N_FDD
Ec/No
average values are
Thresh
larger than or equal
old
to the sum of
HoEcNoThsFDD
and
HoEcNoOffsetUTR
AN, handover from
GSM to UTRAN
takes place and the
adjacent cell is
taken as candidate
destination cell for
handover.
When at least
HoEcNo_P_FDD
Hando
out of
ver
HoEcNo_N_FDD
from
average values are
UTRAN GSM
larger than or equal
Handov to
to the sum of 1..20 N/A 3 3
er UTRA
HoEcNoThsFDD
Control N FDD
and
Ec/No
HoEcNoOffsetUTR
Value
AN, handover from
P
GSM to UTRAN
takes place.
When at least
HoEcNo_P_FDD
Hando
out of
ver
HoEcNo_N_FDD
from
average values are
UTRAN GSM
larger than or equal
Handov to
to the sum of 1..20 N/A 4 4
er UTRA
HoEcNoThsFDD
Control N FDD
and
Ec/No
HoEcNoOffsetUTR
Value
AN, handover from
N
GSM to UTRAN
takes place.
Cell
Priority- re-sele This parameter
based ction determines whether 0: Not
Resel Switch to enable the Support N/A 0 0
Configur Based priority based cell 1:Support
ation on reselection feature.
priority
This parameter
Priority-
Priority indicates the priority
based
of of a GSM cell for
Resel 0..7 N/A 0 0
GSM the priority-based
Configur
cells handover decision
ation
algorithm.
This parameter
indicates a
threshold used in
0:-98
the priority-based
1:-95
cell reselection
thresh algorithm. When 2:-92
old of RLA_C of the local 3:-89
servin cell is lower than 4:-86
g cell this threshold, the 5:-83
Priority- that MS must monitor 6:-80
based used lower-priority
7:-77
Resel by neighbor cells using dBm 15 15
8:-74
Configur priority the other radio
ation Cell 9:-71
access
re-sele technologies. When 10:-68
ction RLA_C of the local 11:-65
algorit cell is higher than 12:-62
hm this threshold, the 13:-59
MS is allowed not to 14:-56
monitor
15:always
lower-priority
neighbor cells using
the other radio
access
technologies.
This parameter
indicates the 0:0 dB
threshold that 1:2 dB
determines whether 2:4 dB
the MS is allowed to
3:6 dB
thresh make a cell
4:8 dB
old reselection to a
that lower-priority cell. 5:10 dB
Priority- 6:12 dB
Allow When both the C1
based
MS value of the local 7:14 dB
Resel N/A 15 15
re-sele cell and that of the 8:16 dB
Configur
ct to GSM neighbor cell 9:18 dB
ation
lower are lower than this
10:20 dB
priority threshold, the MS is
11:22 dB
Cell allowed to make a
12:24 dB
cell reselection to a
lower-priority 13:26 dB
This parameter
indicates the
hysteresis for the
Hyster
cell reselection
Priority- esis of 0:rule
algorithm. Cell
based priority disabled
reselection to a
Resel resele N/A 0 0
neighbor cell using 1:5dB
Configur ction
another radio 2:4dB
ation algorit
access technology 3:3dB
hm
is allowed when the
C1 value of the
neighbor cell is
This parameter
indicates the time
hysteresis for the
cell reselection
algorithm. An MS
Time can only make a
hyster cell reselection to a
Priority- 0:5
esis of neighbor cell using
based
priority another radio 1:10
Resel s 0 0
resele access technology 2:15
Configur
ction when the neighbor 3:20
ation
algorit cell meets the
hm reselection
conditions and
maintains this
situation during the
period specified by
this parameter.
the
Priority-
default This parameter
based
priority indicates the default
Resel 0..7 N/A 4 4
of priority of UTRAN
Configur
Utran cells.
ation
Cells
This parameter
indicates the low
threshold of signal
difference that is
used to determine
cell reselection to a
UTRAN neighbor
the
cell for an MS that
minim
Priority- supports the
um [20,18,
based priority-based cell [20,18,16
thresh 16,14,
Resel reselection 0..31 2dB ,14,12,10
olds of 12,10,
Configur algorithm. When a ,8,6]
Utran 8,6]
ation UTRAN neighbor
resele
cell has a lower
ction
priority than the
local cell, the MS
can make a cell
reselection to the
neighbor cell if the
neighbor cell meets
all the other
This parameter
indicates the 0..31
minimum Rx level
Minim that is used to 0 = -119
Priority-
um RX determine cell dBm, 1 =
based [0,0,0,
level reselection to a -117 dBm, 2 [0,0,0,0,0
Resel N/A 0,0,0,0
for UTRAN neighbor = -115 ,0,0,0]
Configur ,0]
Utran cell for an MS that dBm, …, 30
ation
cells supports the = -59 dBm,
priority-based cell 31 = -57
reselection dBm.
algorithm.
Counter ID Name
6 Engineering Guide
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > External Resource Configuration, and double-click
External UTRAN FDD Cell Configuration. Set the parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration > Adjacent Relation
Configuration, and double-click Adjacent UTRAN Cell Configuration. Set the
parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration, and double-click
UTRAN Measurement. Set the parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration, and double-click
E-UTRAN Measurement. Set the parameters. Usually the enhanced measurement
report is not used, so the parameters are set to the default values. See the following
figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration > GPRS Configuration,
and double-click NC2 Configuration. Set the parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration > GPRS Configuration,
and double-click NACC Configuration. Set the parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration, and double-click
UTRAN Handover Control. Set the parameters. See the following figure.
In the configuration resource tree, select Modify Area > Configuration Management >
GSM Logical Configuration > Cell Information Configuration, and double-click
UTRAN Handover Control. Set Inter system handover supported to No. See the
following figure.
Enabling the 2-3G inter-operation function can integrate the 2G and 3G networks.
Through reasonably configured parameters, the two networks can provide
complementary coverage and network capacities, provide CS service with the 2G
network that has capacity advantages, provides PS service with the 3G network that has
throughput advantages, and provide better user experience.
7 Abbreviation
Abbreviations Full Characteristics
MS Mobile Station
UE User Terminal
8 Reference Document
ZXUR 9000 GSM (V6.50.31) Base Station Controller Performance Counter Reference
ZXUR 9000 GSM (V6.50.31) Base Station Controller Radio Parameter Reference