Академический Документы
Профессиональный Документы
Культура Документы
Before ordering a fire pump, consult FM Approvals regarding size, type of driver, suction supplies and location. Proposals for fire
pump installations, including plans showing location and piping connections, should be sent to FM Global for review before the order
is placed. Give the manufacturer complete data, including rated capacity, net head and suction head. Contracts for pump installations
or changes should be let subsequent to acceptance of plans and subject to satisfactory field tests by FM Global.
The pump manufacturer or his authorized representative is responsible for furnishing a complete unit consisting of pump, driver and
necessary accessories, all according to FM Global's standards.
Satisfactory performance in an operating test after installation should be guaranteed. A new fire pump installation is not acceptable
until FM Global has witnessed a satisfactory field acceptance test. This will include a test of endurance of the pump and reliability of
the power supply.
Exact horsepower requirements for each pump must be determined by a shop test on the specific pump. Approximate horsepower
requirements at rated pump conditions are as follows:
Rated Rated
Capacity, Net Approximate
gal/min Head, Power
(dm3 psi Required,
/min) (kPa) hp (kW)
500 100 50-60
(1895) (690) (37-45)
In the listings on the following page, rated net head represents the amount of pressure boost obtainable from a pump of a given type
and impeller size when operating at rated speed.
The rated net head range indicates that impellers of various diameters are obtainable for the given type of pump.
Although not recommended for installations where suction is normally taken under lift, FM Approved pumps have been tested for
proper operation under negative suction conditions up to 15 ft (5 m) at 150% of rated capacity.
Horizontal Mounted
5x4x12 SSC
Note: Standard construction includes ASA 125 suction and discharge flanges. For ASA 250 discharge flanges, suffix H is
added to type designations.
Rated Rated
Capacity, Net Approximate
gal/min Head, Power
(dm3 psi Required,
/min) (kPa) hp (kW)
500 100 50-60
(1895) (690) (37-45)
In the listings on the following page, rated net head represents the amount of pressure boost obtainable from a pump of a given type
and impeller size when operating at rated speed.
The rated net head range indicates that impellers of various diameters are obtainable for the given type of pump.
Although not recommended for installations where suction is normally taken under lift, FM Approved pumps have been tested for
proper operation under negative suction conditions up to 15 ft (5 m) at 150% of rated capacity.
Horizontal Mounted
5x4x12 SSC
Note: Standard construction includes ASA 125 suction and discharge flanges. For ASA 250 discharge flanges, suffix H is
added to type designations.
Clarke Fire Protection Products Inc. Clarke Fire Protection Products Inc.
3133 E Kemper Rd. 100 Progress Place
Cincinnati, OH 45241 Cincinnati, OH 45246
United States United States
Said Approval is subject to satisfactory field performance, continuing Surveillance Audits, and strict conformity to the
constructions as shown in the Approval Guide, an online resource of FM Approvals.
Richard B. Dunne
Manager of Fire Protection
FM Approvals
1151 Boston-Providence Turnpike
Norwood, MA 02062
Page 1 of 14
Certificate of Compliance
Rated Rated Rated Certification
Product Listing Country
Power, hp Power, kW Speed, r/min Type
)LUH3XPS&RQWUROOHUV'LHVHO(QJLQHV
&RQWUROOHUVSURYLGHDQDXWRPDWLFPHDQVIRUVWDUWLQJLQWHUQDOFRPEXVWLRQHQJLQHGULYHQILUHSXPSXQLWV([FHSWDVQRWHGEHORZWKHVH
FRQWUROOHUVDUHGHVLJQHGIRUGXDOEDWWHU\RSHUDWLRQ
0RGHO)7$
0RGHO)7$-DEFG
D /HDGDFLGRUQLFNHOFDGPLXPEDWWHULHV/RU1
E 9ROWDJHRU
F *URXQG1RU3
G 2SWLRQV$$$$%$&$'$($)$*$+$,$-$.$/$0$1$3$4$5$6$7$8$9$:$<$=%%$%*
%7%8%9%=%=(%=)&&$&%&&&'&2$&20&4$&4$'&40&6$&60&3/&76&8$&8$'&80
&:$&:0&<$&<0''%''(((()(*(+(-(.(/(0(0,(1(3(9(:(;(<(=))')-)05*
*($*(0*/*/5*/6*1*6$*60*7$*7$'*8$*80*9$*9$'*90*=++$$+$0+(%+++/(+0
+1+3+5+6%+7+9,(&--$-5-7..).+.9$.90.<.=//%/&/'/(/)/*/+/-/0/1/3
/5$/50/6$/60/7$/70/9$/:$/</=00*0+0-0.0/00010305060708090:0<
0<'0<'=0<(0<(=11=3$3$53%$3%03(3*3+3-3.3/33383=555565675758595:
66<77*78%8)8.$8.%8.08.:8586$8609:9=:7:8:9:::<:=;<5<;=/$=/%=/&
=/'=/(=05=06=07=09=0:=1$=1%=1&=1&=1'=1(=1(=1*=1+=1-=1.=1/=10=14=15
=16=17=18=19=1:=1==3$=3%=3&=3'=30=31
&RPSDQ\1DPH $6&23RZHU7HFKQRORJLHV/3
&RPSDQ\$GGUHVV 'LOODUG'U6XLWH&DU\1RUWK&DUROLQD86$
&RPSDQ\:HEVLWH KWWSZZZDVFRFRP
/LVWLQJ&RXQWU\ 8QLWHG6WDWHVRI$PHULFD
&HUWLILFDWLRQ7\SH )0$SSURYHG
)0$SSURYDOV$OOULJKWVUHVHUYHG RI
0RGHO)7$DEFGHI(OHFWULF0RWRU)LUH3XPS&RQWUROOHU/RZ9ROWDJH
!
"
#"$%&
'
(
)
*+,
-.,/
0'',
-12,/
D E F G
6WDUWLQJ0HWKRGV 6WDUW6WRS2SWLRQV :LWKVWDQG5DWLQJ +RUVHSRZHU
0222
&
!
0227222
2*7
217
2>
->0$'
<3/7
027
017
0'12
3
4
)!
'22922: '27
'17
*27
.27
127
927
>17
0*22
4
5
(
#
;
0127222
0227
0'17
0127
'227
'127
*227
7 )!
'22922: *127
.227
.127
1227
9227
>22
0*12
4
5
3
<
'227222
)!
'22922:
0122
3
)
8
=
!
;
0622
917222
)!
'22.62:
0+22
!
!
!
! )
!
&
.'7222
0+*2
5
!
!
! )!
112922:
!
H 9ROWDJH9DF+] I 0RGLILFDWLRQV
''2'.2 6SHFLDO(QFORVXUHV
?
''2'*2
-12
<@/
#"
*)
8
..2.62 "
#"
.
8?
.01
-12
<@/
#"
.A
B*2.
!
!
112922 A3
#"
.A
B*2.
3
!
*62 5
#"
.A
B*09
!
!
?
*62
-12
<@/ 58
#"
.A
B*09
8 7
!
!
<
'26 53
#"
.A
B*09
3
!
<<
'22 C
#"
0'
$XWRPDWLF3RZHU7UDQVIHU6ZLWFKHV
+22
+20
+12
+10
3UHVVXUH7UDQVGXFHUV
8
2922
-2.''1
/
4
2*22
-2'00
/
!
5
2922
-2.''1
/
!
$QWL&RQGHQVDWLRQ6SDFH+HDWHUV
<
0'2:
D
0'2:
$
E
0'2:
$<
&
'.2:
'.2:
$
#
'.2:
$<
!(
3
&3
000
57
!
0'27
7
#
'>1007
%!
$$
!"#
$
% #
$
%
%
!
&
F
'22>'209
0
'
Not to be distributed outside of FM Approvals and its affiliates except by Customer
APPROVAL REPORT
WATER PRESSURE RELIEF VALVES
MODIFICATION
Prepared for:
Cla-Val Co.
17th St & Placentia Ave.
PO Box 1325
Newport Beach, CA 92659-0325
Authorized by:
Richard B. Dunne, Manager - Fire Protection Group
FM Approvals
1151 Boston-Providence Turnpike
P.O. Box 9102
Norwood, MA 02062
Page 1 of 7
FM APPROVALS
PROJECT ID: 3045403
MODIFICATION
from
Cla-Val Co.
17th St & Placentia Ave.
PO Box 1325
Newport Beach, CA 92659-0325
I INTRODUCTION
1.1 Cla-Val Co. requested an Approval examination of their water pressure relief valves, Model 50B-
4KG1 and 2050B-4KG1, in sizes 3, 4, 6 and 8 inch NPS with alternative pilot valves and cover plate
bolts from those currently FM Approved and discussed in the Approval Report for Project ID
0Y2A4.AH dated June 16, 1995.
1.2 This Report may be reproduced only in its entirety and without modification.
1.3 These devices were examined in accordance with the requirements of the FM Approval Standard
listed below:
1.4 The devices discussed in this Report will appear in the Approval Guide, an online resource of FM
Approvals, under Fire Protection / Fire Pump Installation Systems / Water Relief Valves. See
Appendix I for the complete Approval Guide listing for this product.
II DESCRIPTION
The Model 50B-4KG1 and 2050B-4KG1 water pressure relief valves discussed in this Report have
a rated working pressure of 300 psi (2070 kPa) for sizes 3, 4, 6 and 8 inch NPS.
2.2 Design
The Model 50B-4KG1 and 2050B-4KG1 water pressure relief valves discussed in this Report
remain unchanged from those discussed and Approved under Approval Report ID 0Y2A4.AH
dated June 16, 1995 except for the following modifications:
Page 2 of 7
FM APPROVALS
PROJECT ID: 3045403
x Cover plate bolts, studs and nuts ± alternative material, 303 Stainless Steel
x Pilot Valves ± see Table 2.2
The alternative pilot valves for the water pressure relief valves covered in this Report are provided
below.
The water pressure relief valves discussed in this Report have an adjustable outlet pressure range
from either 20 psi (135 kPa) to 200 psi (1380 kPa) or 100 psi (670 kPa) to 300 psi (2070 kPa)
depending on the supplied pilot valve and pilot valve spring. Please refer to Approval Guide listing
in Appendix I for all Approved water pressure relief valve configurations.
Sample 4 and 8 inch NPS Model 50B-4KG1 water pressure relief valves, considered
representative of all valves discussed in this Report, were tested for hydrostatic strength. Sample
water pressure relief valve were subjected to a hydrostatic pressure of 1200 psi (8280 kPa) for
five minutes. This pressure represents four times the rated working pressure. There was no
apparent damage to the bodies of either valve as a result of this test. These results are considered
satisfactory.
Sample Model CRL60 pilot valves in bronze and stainless steel, considered representative of all
pilot valves discussed in this Report, were subjected to hydrostatic strength testing. The
samples were subjected to a hydrostatic pressure of 1200 psi (8280 kPa) for five minutes. This
pressure represents four times the rated working pressure. There was no apparent damage to the
bodies of any valve as a result of this test. These results are considered satisfactory.
Page 3 of 7
IX CONCLUSION
The Cla-Val Co. water pressure relief valve, Model 50B-4KG1 and 2050B-4KG1, in sizes 3, 4, 6 and
8 inch NPS, as discussed in this Report meet FM Approvals requirements when manufactured at the
facility listed in Section VI. Since a duly signed Master Agreement is on file for this manufacturer,
Approval is effective the date of this Report.
________________________________ ________________________________
Joseph M. Looney Stanley M. Ziobro
Engineer ± Fire Protection Technical Team Manager ± Fire Protection
Page 6 of 7
FM APPROVALS
PROJECT ID: 3045403
APPENDIX I
50B-4KG1, 2050B-4KG1
Cat. Nos. 50B-4KG1, 2050B-4KG1. 3, 4, 6, 8 in. NPS (76, 102, 152, 203 mm). Assembly consists of Clayton 100
(globe) or Clayton 2100 (angle) hydraulically operated, diaphragm-actuated valve, pilot valve (FM Approved pilot
valve configurations are listed below), Clayton X44A, X46A strainers, Clayton Model 81-01 check valve, pressure
JDXJHDQG»LQPPGLDRULILFHDVVHPEO\&OD\WRQ;&YDOYHSRVLWLRQLQGLFDWRULVDYDLODEOHDVRSWLRQDO
equipment.
Model CRL, bronze body, spring range of 20 psi (135 kPa) to 200 psi (1380 kPa)
Model CRL, bronze body, spring range of 100 psi (670 kPa) to 300 psi (2070 kPa)
Model CRL60, bronze body, spring range of 20 psi (135 kPa) to 200 psi (1380 kPa)
Model CRL60, bronze body, spring range of 100 psi (670 kPa) to 300 psi (2070 kPa)
Model CRL60, stainless steel body, spring range of 20 psi (135 kPa) to 200 psi (1380 kPa)
Model CRL60, stainless steel body, spring range of 100 psi (670 kPa) to 300 psi (2070 kPa)
Class 300 inlet, Class 150 outlet, 250 psi rated working pressure;
Class 300 inlet, Class 300 outlet, 400 psi rated working pressure;
Class 150 inlet, Class 150 outlet, 250 psi rated working pressure.
Models identified with the suffix "KC" indicate epoxy coated valves.
Catalog No. 750B-4KG. 3, 4 in. NPS (76, 102 mm). Wafer style valve. 300 psi (2070 kPa) rated working pressure
assembly consists of a Roll Seal Series 100-42 hydraulically operated valve, Clayton CRL5A pressure relief control
available with spring ranges of 20-200 psi (140-1380 kPa) and 100-300 psi (690-2070 kPa), Clayton X43 strainer,
Clayton Model 81-01 check valve, pressure gauge and Clayton Model X58X orifice assembly.
Model 850 B, 4, 6, 8, in. NPS (102, 152, 203 mm). Rated working pressure 250 psi (1725 kPa). Assembly consists of
the Model 100-43 TDV hydraulically operated, diaphragm-actuated valve, Clayton CRL pressure relief control 20-200
psi (140-1380 kPa), Clayton X44A strainer and orifice assembly, Clayton Model 81-01 check valve and pressure
gauge.