Вы находитесь на странице: 1из 2

SRI VIVEKANANDA PRIVATE INDUSTRIAL TRAINING INSTITUTE

(AFFILIATED TO NCVT, NEW DELHI, DGET NO. 6/10/8/2007 TC PVT)


SONNASHETTIHALLI, KOLAR ROAD, CHINTAMANI-563125, KARNATAKA

DATE:27/09/2018 SUBJECT: TRADE THEORY (231) TRADE: Electrician (EN-03)


TOTAL TIME: 120 MIN TEST NO:01 TOTAL MARKS: 75

Note: 1) Attempt all the questions and all questions carry equal marks.

1) The speed of rotating magnetic flux of a 3-phase 2) In a 3-phase induction motor started by
induction motor is given by the DOL starter, protection against short-
a)120P/F circuit is given by
b)P.F/120 a) Overload relay
c) 120F/P b) No-volt coil
d) F/120P c) Back-up fuses
d) Protective earth contractor
3) Squirrel cage IM differs from slip ring IM as it 4) The frequency of the rotor current in an
has no induction motor is given by the
a) Slip-rings a) F=s.fr
b) Rotor windings b) Fr=s.f
c) Stator windings c) Fr=s/f
d) Rotating part d) S=f.fr
5) Total electrical degrees for a 4 pole AC machine is 6) A 3-phase, 400v, 50 Hz induction motor
equal to has a rated speed of 715 r.p.m. how many
a) 1800 poles are there in the machine?
b) 3600 a) 2
c) 7200 b) 4
d) 10800 c) 6
d) 8
7) Minimum requirement of contacts in a 3-phase 8) DOL starters are used up to
DOL starter is a) 1kw
a) 4 Nos. b) 1.5kw
b) 3 Nos. and one NC c) 3kw
c) 3 Nos. d) 5kw
d) 2 Nos. and 2 NC
9) One kilogram of force= _________________ 10) Thermal overloads are ___________
a) 9.81N than the magnetic overload relays.
b) 8.72N a) faster
c) 6.84N b) slower
d) 5.25N c) much bigger
d) very slower
11) The magnetic flux produced in the stator of a 3 12) The speed at which the field rotates is
phase IM travels at ........ called
a) Rotating speed a) Rotating speed
b) Asynchronous speed b) Asynchronous speed
c) Synchronous speed c) Synchronous speed
d) Slip speed. d) Slip speed
13) In the manual star delta starter, the stop button 14) Calculate the percentage slip of an IM
connection is in series with the having 4 pole fed with 50 cycles supply
a) No-volt coil rotating with an actual speed of 960rpm.
b) Overload relay contacts a) 2
c) No-volt coil and load relay contacts b) 3
d) No-volt coil and start button c) 4
d) 5
15) Determine the rotor frequency, if slip is 4% and 16) Insulation resistance is measured using
stator frequency is 50Hz. a) tachometer
a) 2 b) tong tester
b) 3 c) meggar
c) 4 d) clamp on meter
d) 5
17) The purpose of using starters in IM is 18) _________ is used for making rotor and
a) to increase the starting current stator cores.
b) to limit the starting current a) Silicon steel
c) both a and b b) Cast iron
d) none c) aluminium
d) phosphor bronze
19) The frame of IM is usually made of 20) Slip rings are usually made of
a) carbon a) copper
b) silicon steel b) carbon
c) copper c) phosphor bronze
d) cast iron d) aluminium
21) In IM, percentage slip is found in the range of 22) Which type of starter is used to start slip
a) 100% ring IM.
b) 0% a) DOL starter
c) 5% b) Auto-transformer starter
d) 40% c) Rotor-resistance starter
d) Star-delta starter
23) Calculate no of poles of 3-phase IM running at 750 24) Calculate the percentage slip of an IM
rpm with 50 Hz frequency. having 4 pole fed with 50 cycles supply
a) 2 rotating with an actual speed of 1440rpm.
b) 4 a)6
c) 6 b)4
d) 8 c) 5
d)3
25) What is the phase angle difference between each
phase winding of 3-phase IM?
a) 900
b) 1200
c) 1800
d) 3600

**********ALL THE BEST*************

Вам также может понравиться