Академический Документы
Профессиональный Документы
Культура Документы
Warnings
Notice
✔ Service must be carried out by qualified personnel only.Any tampering carried out by unqualified personnel during the guarantee period
will forfeit the right to guarantee.
✔ For a correct operation of the instrument, after having switched off, be careful to wait at least 3 seconds before switching on again.
✔ To improve the device's specifications, the schematic diagrams may be subject to change without prior notice.
All components marked by this symbol have special safety characteristics, when replacing any of these components use only
manufacturer's specified parts.
SERVICE MANUAL
✔ The (µ) micro symbol of capacitance value is substituted by U.
✔ The (Ω) omega symbol of resistance value is substituted by E.
✔ The electrolytic capacitors are 25Vdc rated voltage unless otherwise specified.
✔ All resistors are 1/8Ω unless otherwise specified.
✔ All switches shown in the "OFF" position. All DC voltages measured to ground with a voltmeter 20KOhm/V.
ATTENTION
Observe precautions when handling electrostatic sensitive devices.
Address
CODE: 270217 ✔
✔
GENERALMUSIC S.p.A. Sales Division: 47842 S.Giovanni in Marignano (RN) ITALY - Via delle Rose, 12 - tel. 0541/959511 - fax 0541/957404
GENERALMUSIC on the NET: http://www.generalmusic.com
1❏
Opening Instructions
Disconnect the instrument from the mains.
Carefully turn the instrument over and unscrew the screws
marked with the arrows.
Hold the chassis (top & bottom) tightly and turn the istru-
K2 K2 K2 K2 K2 K2 ment the right way up, lift off the top chassis as shown
below with care without forcing or disconnecting the cables.
K1 K1 K1 K1 K1 K1
61 Notes
Keyboard Separation
(open the instrument before proceed)
To separate the keyboard from chassis, carefully turn the
bottom chassis from horizontal to vertical, remove the
screws marked by K1 , put it back horizontal, holding
top & bottom chassis move these tightly to the end of your
job table, now unscrew the screws marked with K2
to reassemble the keyboard & the chassis follow the instru-
ctions in reverse order.
K2 K2 K2 K2 K2 K2 K2 K2
K1 K1 K1 K1 K1 K1 K1 K1
76 Notes
Remove the key return spring Unlock the key appling not much strenght
Note: To remove a sharp key before
DRW Boccato DWG# 550151 PCB# GENERALMUSIC S.p.A. ITALY
you must remove a near natural key. Opening Instructions ALL RIGHTS ARE RESERVED, NO COPIES
CKD Consorte DISK: 65 PRT: 1/1
Keyboard Disassembling Instructions OR REPRODUCE THIS DOCUMENT WITHOUT
APP. Orsetti REV: 30/09/98 WRITTEN CONSENT BY GENERALMUSIC.
❏2
68 61 69 Label: see note on part list
67 66 65 64 61 60 62 63
GAIN 2 GAIN 1 2 2 2 1 RIGHT LEFT IN 1 OUT 1 THRU 1 IN 2 OUT 2 THRU 2 COMPUTER VOLUME 1 2 DAMPER SCSI
USER
4 5 6
7 8 9
DRAWBARS
F1 F2 F3 F4 0
CONTROLLERS
TRANSPOSE
29 35 46 47 54 48 49 50 51 52 53 58 56 57 59 55 41 30
Note: for descriptions and codes refer to Ref column on spare part list above on this manual.
3❏
Note: For part descriptions and codes refer to spare part list above on this manual (REF column).
34 This drawing shows the 1st version 76 keys with traditional supply, the 61 keys is similar.
33
35
PITCH ADJ 36 37 42 38 39 40 41
32
CN4
Pcb#315153
CN3
VR11
CN1
Pcb#315157
CN1
Pcb#315113
CN2
CN2
CN3
CN1 CN6
CN5
1 2 3 7 8 9 10 11 12 13 14 15 16
Pcb#315149
CN1
Pcb#315163
CN1 Pcb#315088
AFTER
4 5 6 24 23 22 25 21 TOUCH 17-18-19 20 26 31
ADJ
CN9
CN12
CN2 CN3
CN17
CN4
CN3 8MB DRAM
CN2 CN6 CN5
Pcb#315014 CN1 2MB DRAM
CN6 CN2 CN16
CN4
CN8 SIMM17
Pcb#315116 CN5 Pcb#315092/1 SIMM18
CN1
CN7 CN8
CN7
Pcb#315150
2MB DRAM
CN10
CN3
CN15
VR1
CN11 CN13 30
30
CN6 CN7
TO R CONTACTS BOARD Pcb#315114
CN5 CN1
TO L CONTACTS BOARD CN1 CN6 AFTER
CN3 CN4 Pcb#315024 TOUCH
28
Pcb#315118
CN1
❏4
Note: For part descriptions and codes refer to spare part list above on this manual (REF column).
34 This drawing shows the 2nd version 76 keys with switching supply, the 61 keys is similar.
33
35
PITCH ADJ 36 37 42 38 39 40 41
32
CN4
Pcb#315153
CN3
VR11
CN1
Pcb#315157
CN1
Pcb#315113
CN2
CN2
CN3
CN1 CN6
CN5
1 2 3 7 8 9 10 11 12 13 14 15 16
Pcb#315149
CN1
Pcb#315163
CN1 Pcb#315088
AFTER
45 44 43 24 23 22 25 21 TOUCH 17-18-19 20 26 31
ADJ
CN12
CN2 CN3
CN17
CN4
CN5 8MB DRAM
CN6
CN8 CN1 2MB DRAM
CN4 CN2 CN16
CN7
SIMM17
CN6 Pcb#315092/1 SIMM18
CN5
CN8
CN7
CN3
CN2 Pcb#315150
TB2
Pcb#850-9541-M Pcb#315151 2MB DRAM
TB1 CN1 CN10
CN3
CN15
VR1
CN11 CN13 30
30
CN6 CN7
TO R CONTACTS BOARD Pcb#315114
CN5 CN1
TO L CONTACTS BOARD CN1 CN6 AFTER
CN3 CN4 Pcb#315024 TOUCH
28
Pcb#315118
CN1
5❏
DRW Boccato DWG# 550155 PCB# GENERALMUSIC S.p.A. ITALY DRW Boccato DWG# 550165 PCB# GENERALMUSIC S.p.A. ITALY
CKD Consorte DISK: 65 PRT: 1/1 Block Diagram ALL RIGHTS ARE RESERVED, NO COPIES CKD Consorte DISK: 65 PRT: 1/1 Block Diagram ALL RIGHTS ARE RESERVED, NO COPIES
1st Version with traditional supply OR REPRODUCE THIS DOCUMENT WITHOUT 2nd Version with switching supply OR REPRODUCE THIS DOCUMENT WITHOUT
APP. Consorte REV: 25/09/98 WRITTEN CONSENT BY GENERALMUSIC. APP. Consorte REV: 25/09/98 WRITTEN CONSENT BY GENERALMUSIC.
❏6
7❏
❏8
MIDI & CONTROLS I/O BOARD (PCB#315088)
DRW: BOCCATO DWG: 315088/116 SCHEMATIC DIAGRAM EQUINOX GENERALMUSIC S.p.A. Italy
CKD: RICCOBELLI DISK: 65 PART: 1/1 Power Supply, Midi & Controls and ALL RIGHTS ARE RESERVED, NO COPIES
OR REPRODUCE THIS DOCUMENT WITHOUT
APP: PANNELLI REV: 08-10-98
Phones Board Pcb Layout WRITTEN CONSENT BY GENERALMUSIC.
9❏
ANALOG I/O BOARD (PCB#315163)
MIXER BOARD (PCB#315151/2) DRW: BOCCATO DWG: 315151/163 SCHEMATIC DIAGRAM EQUINOX GENERALMUSIC S.p.A. Italy
CKD: RICCOBELLI DISK: 65 PART: 1/1 Mixer Board and Analog I/O Board Pcb ALL RIGHTS ARE RESERVED, NO COPIES OR
REPRODUCE THIS DOCUMENT WITHOUT
APP: PANNELLI REV: 09-10-98
Layouts WRITTEN CONSENT BY GENERALMUSIC.
❏ 10
11 ❏
810669 - CONTROLS PANEL BOARD
+5V
R8 100K
IC1-A
SW12 +5V 74HC86 IC1-B +5V
1 74HC86 IC2-B 74HC74
R10 1K 3 12
C18 100N
C17 100N
C36 100N
C35 100N
C37 100N
C16 100N
C33 100N
2 11 11 CK Q 9
C9 100N
14 14 14 14 14 14 14 14
C31 100N
13
C1 10U
IC3-C IC2-C IC8-B IC7-B IC9-B IC1-E IC5-B IC6-B
C20 100P
D FF
C15 820P
R2 22K 12 D 74HC74 74HC74 74HC164 74HC164 74HC164 74HC86 74HC164 74HC164
Q 8
7 7 7 7 7 7 7 7
R S
DIAL
13 10 +5V
+12V
+5V
+5V C29 100N
C13 100N
100K
IC3-A 74HC74 IC3-B 74HC74
IC1-D 8
3 CK Q 5 11 CK Q 9
FIX POINTS
+5V 74HC86 IC1-C C23 100N
IC4-C
VARIOUS
5 74HC86 IC2-A 74HC74 TL072
D FF D FF
R7
R12 1K 6 9 C22 100N
4 8 3 CK Q 5 2 D Q 6 12 D Q 8 4
10
R S R S
C21 100P
D FF C39 100N
C14 820P
R3 22K C26 100N
761169 - CONTROLS INTERFACE BOARD 2 D Q 6 1 4 +5V 13 10
PROGRAM ARP.
-12V
+12V R S
CN5 +5V +5V 1 4 +5V
FROM POWER AMP. & SUPPLY BOARD CN5
C37 100N
1 +12V
C38 10U
SYSTEM
C15 100N
C13 100N
C29 100N
C30 100N
100N
2 LGND 20 20
C2 100N
14 39 30 14
DISK
MIDI
CONTROLS PANEL SUPPLY
C1
9 10 9 10 16 48 21 7
5 PEAK-1
D0
D1
D2
D3
D4
D5
D6
D7
D0
D1
D2
D3
D4
D5
D6
D7
CN4
C12 100N
6 PEAK-2 CN1
10U
3K3
7 LGND D7 1 1 D7 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3 3
+5V 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
8 D6 2 2 D6
R24
C11
POT1
SW10
SW11
SW14
SW15
SW62
SW24
SW16
SW25
SW26
SW45
SW44
SW43
9 +5V D5 3 3 D5
SW5
SW6
SW7
SW9
10 D4 4 4 D4
C35 100N
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
R21 4K7
C36 10U
D3 5 5 D3 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
10U
11 NC
C33 100N
A10
A12
12 -12V D2 6 6 D2
D1 7 7 D1
C34
A8
A9
D0 8 8 D0
-12V
NC 9 9 LGND
VEE 3 3 3 3 3 3 3 3 4 4 4 4 4 4 4 4
10 10 EN_LED 2 2 2 2 2 2 2 2 1 1 1 1 1 1 1 1
VLCD
SW52
SW53
SW54
SW55
SW56
SW57
SW58
SW59
SW60
SW27
SW13
SW42
SW22
SW23
SW28
SW61
+5V
R10 3K3
1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2
4 4 4 4 4 4 4 4 3 3 3 3 3 3 3 3
R14 3K3
HD LED
+5V CN2
R13 3K3 AR1 CN3
10K X8 1 +5V 1 +5V
STOP D1
D1 PERC 2 2 / 3’ ENTER D1
PLAY D0
D2
D3
RECORD D4
SONG SEL. D5
SONG EDIT D6
PROGRAM D7
D0 PERC 4’ GROOVES D0
D2
ESCAPE D3
D4
D5
D6
ARP. ON\OFF D7
DIR 1 2
STOP
+5V
GROOVES
TO CONTROL INT. BOARD CN3
TR2 4
<<
>>
FQ 3
BC550C 4 5
R33 180E
IC3 VALIS100740 CLK 5 6
6 7
CONTROLS PANEL PITCH BEND 22 P7,0/AN0 D0/P3,0 57 9 8 7 6 5 4 3 2 D0 8
D5 SEL. 1-8/7-16
SD 7
D6 DRAWBARS
8 9
MODULATION 23 P7,1/AN1 D1/P3,1 58 D1 VEE 9 10
11 DL18
D0 LAYER 1
D1 LAYER 2
D2 LAYER 3
R66 1K FOOTSW2 24 P7,2/AN2 D2 10
FROM CPU & S.G. BOARD CN2 D2/P3,2 59 VLCD 11 12
D2 SLOW
D3 CLICK
D4 USER
13
D3 FAST
CN6 R64 1K PEDAL V. 25 P7,3/AN3 D3 12 HD_LED A15
D3/P3,3 60 A15 13 14 A14 TRANSPOSE
14 A13 15 DISK # -
1 2 FOOTSW1 R62 1K FOOTSW1 26 P7,4/AN4 D4/P3,4 61 D4 A14 16 b
D7 +
A13 15 A12
16 A11 17
4 PEDAL1 R61 1K FOOTSW3 D5 A12
D4
D5
D6
3 27 P7,5/AN5 D5/P3,5 62 17 18 A10
A11 18 19
5 6 PEDAL2 R43 1K POT.9 28 P7,6/AN6 D6 A10 A9
D6/P3,6 63 A9 19 20 A8
20
C28 100N
C27 100N
C26 100N
C18 100N
C17 100N
C16 100N
C14 100N
SW29
SW30
SW31
SW32
SW46
SW47
SW48
SW49
SW33
SW34
SW35
SW36
SW37
SW17
SW8
13 14 PEDAL V. +5V +5V 1
1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
10K X4
VR101 5KB
15 16 RSTV 4 4 4 4 4 4 4 4 4 4 4 4 4 4 4
R56 10K
R60 10K
CONTRAST
1
AR3
AC1
A14 A11
A15
47P X8
IC1-A FQ 5 3 4 2
74HC125 1 P4,0/ADTRG//IRQ2 A0/P1,0 56 +5V
R1 15K
A13
GET_TXD R54 560E 2 3 GET_TXD 2 P4,1/IRQ1 A1/P1,1 55
100740 - PERIPHERIAL CPU
SW39
SW51
SW50
SW38
SW40
SW41
SW18
SW19
SW20
SW21
SW1
SW2
SW3
SW4
R58 560E A3 6 P4,5/AS A5/P1,5 51
RXD3 5 6 1
+5V DIR 7 P4,6/CLK0 A6/P1,6 50 4 1 1 1 1 1 1 1 2 2 2 2 2 2
IC1-D 4 4 4 4 4 4 4 3 3 3 3 3 3
74HC125 4 8 P4,7/WAIT A7/P1,7 49
13
F1 D0
F2 D1
F3 D2
F4 D3
STORE D4
NOTEPAD D5
UNDO D6
HELP D7
PERFORM D1
FX OFF D3
SOLO D4
SOUND D5
DRUM D6
SAMPLE D7
NEXT R7 330E 11 12 R9 10K
9 P5,0/TXD A8/P2,0 47 D9 4148 R33 100E
10 P5,1/RXD A9/P2,1 46 D10 4148 R34 100E
R41 100K
R38 100K
R39 100K
SONG SELECT
IC4 74HC4351 +5V A12/P2,4 43 D12 4148 R37 100E GROOVES
R11 10K 13 NMI LIB. GROOVES LIB.
SELECT 9-16
R42 100E
DRAWBARS
R59 1K 17 X0 XC 4 A13/P2,5 42 D14 4148 R47 100E
SONG EDIT
SELECT1-8
PERFORM.
3’
PROGRAM
PROGRAM
15 STBY
2 2/
RECORD
R57 1K D16 4148 R48 100E
SOUNDS
18 X1 A14/P2,6 41
SYSTEM
LAYER 3
LAYER 1
LAYER 2
SAMPLE
DEMULTIPLEXER
ON-OFF
PERC 4’
FX OFF
A0 15 R12 10K
MULTIPLEXER
DRUM
SLOW
CLICK
R50 1K 19 X2 A15/P2,7 40 D15 4148 R46 100E
USER
SOLO
PERC
STOP
STOP
PLAY
FAST
TRANSPOSE
A1 13 17 XTAL
MIDI
R51 1K 16 X3
R25 2K2
R32 2K2
>>
<<
b
+
#
-
R55 1K 1 X4 A2 12 R31 1M
18 EXTAL TMCI0/FTCI/P6,0 31
LE 11 +5V
R30 100E
R40 1K 6 X5 FTOA/P6,1 32
R57 560E
R58 560E
R59 560E
R60 560E
R36 560E
R37 560E
R56 560E
R55 560E
R46 560E
R53 560E
R54 560E
R34 560E
R35 560E
R11 560E
R51 560E
C34 1N
BAUD RATE3
R6 560E
DL35 R61 560E
R28 560E
R26 560E
R27 560E
R24 560E
R22 560E
R23 560E
5 4 3 2
5 X7 E2 8 XT1 TMRI0/FTIB/P6,3 34
20MHZ
TMO0/FTIC/P6,4 35
20 MD0 TMCI1/FTID/P6,5 36 1
DL31
DL32
DL33
DL34
DL14
DL15
DL30
DL29
DL26
DL27
DL28
DL12
DL13
DL24
DL1
DL2
DL9
DL7
DL8
DL5
DL3
DL4
19 MD1 TMRI1/FTOB/P6,6 37
+5V TMO1/P6,7 38 AR2 2K2 X4 +5V +5V +5V
R29 10K
POT1
R44 1K
R53 560E
R65 10K
TR1
BC327
C39 100N
POT3 R17 1K 19 X2 R52 100E R47 100E 1 A +5V 1 A +5V 1 A +5V 1 A +5V 1 A +5V
R44 1K R40 1K R43 1K R42 1K R41 1K
1
2 POT4 R20 1K 16 X3 A1 13 8bit Sin Pout MR 9 8bit Sin Pout MR 9 8bit Sin Pout MR 9 8bit Sin Pout MR 9 8bit Sin Pout MR 9
C32 100P
2 B 2 B 2 B 2 B 2 B
3
POT5 R15 1K 1 X4 A2 12 R32 100E SHIFT REGISTER SHIFT REGISTER SHIFT REGISTER SHIFT REGISTER SHIFT REGISTER
4 8 CP 8 CP 8 CP 8 CP 8 CP
5 LE 11 +5V
POT6 R23 1K 6 X5
C32 100P
6
C38 100P
M.VOL. 7 IC9-A 74HC164 IC8-A 74HC164 IC7-A 74HC164 IC6-A 74HC164 IC5-A 74HC164
8 POT7 R16 1K 2 X6 E1 7
MODULATION 9
10 POT8 R22 1K 5 X7 E2 8 R49 100E
PITCH_BENDER 11
12
100N
100N
100N
100N
100N
C10 100N
100N
100N
+12V
C31 33P
13
14 +12V
15
16 VOLUMES
C7
C6
C5
C8
C3
C4
C9
R16 47K
TO CONTROLS INT. BOARD CN2
-12V +12V
FROM CONTROLS PANEL BOARD CN1
VOLUMES PCB# 315113
VR11 22K
VOLUMES ENVELOPE FILTER LFO PITCH
CENTER ADJ.
C24 10U
C30 10U
CUT-OFF
MASTER
-12V
ATTACK
RESON.
IC4-A
DECAY
DEPTH
LEVEL
+5V +12V CN3
INPUT
TL072 3
RATE
CN1 -
10KB
C25 100N
+5V R13 3K3 9
R14 10K
16 TR2 R15 1K 1
15 BC239C R19 8K2 8
14
VR1 10KB
VR2 10KB
VR3 10KB
VR4 10KB
VR5 10KB
VR6 10KB
VR7 10KB
VR8 10KB
VR9 10KB
VR10 10KB
13 2 R21 1K 7
D1 4148
12
11 -12V LGND 6
10 R17 10K +
9 5
8
7 R18 1K C27 100N +5V 4
6 -
10KB
5 3
C28 100N
R20 5K6
4 TR1 R9 1K
3 2
2 BC239C
1 1
+
R5 1K
C19 100N
R4 1K
C10 100N
C11 100N
C12 100N
C2 100N
C3 100N
C4 100N
C5 100N
C6 100N
C7 100N
C8 100N
6
5
IC4-B
TL072
PCB#315153
DRW G.BOCCATO DWG# 550160 PCB# 315113, 315153 GENERALMUSIC S.p.A. ITALY
CKD G.CONSORTE DSK# 65 PART: 1/1 SCHEMATIC DIAGRAM ALL RIGHTS ARE RESERVED, NO COPIES
CONTROL INTERFACE BOARD OR REPRODUCE THIS DOCUMENT WITHOUT
APP. G.CONSORTE REV: 01-10-98 CONTROLS PANEL BOARD WRITTEN CONSENT BY GENERALMUSIC.
❏ 12
CONTROLS PANEL BOARD reverse layout (PCB#315153)
13 ❏
❏ 14
15 ❏
CPU & SOUND GENERATOR BOARD (PCB#315150)
DRW: BOCCATO DWG: 315150 SCHEMATIC DIAGRAM EQUINOX GENERALMUSIC S.p.A. Italy
CKD: RICCOBELLI DISK: 65 PART: 1/1 Cpu & Sound Generator Board Pcb ALL RIGHTS ARE RESERVED, NO COPIES
OR REPRODUCE THIS DOCUMENT WITHOUT
APP: PANNELLI REV: 07-10-98
Layout WRITTEN CONSENT BY GENERALMUSIC.
❏ 16
J1 - Set the jumper as follow:
1-2 "A" if Buffer modules are installed J2 - Set this jumper as follow:
CN2 - to Controls Panel Board CN3 - to MIDI I/O Board
2-3 "B" if SIMM DRAM modules are installed 1-2 for 8MB SAMPLE DRAM expansion
note: the buffer modules are supplied 2-3 for 2MB SAMPLE DRAM expansion
with Vocal processor kit, if if no DRAM expansion is installed
CN17 to Lcd Display neither buffer or Simm modules are the jumper position must be 1-2.
CN4 & CN12 to installed, J1 position is ininfluent.
Vocal Processor Board
CN5 - SAMPLE DRAM Expansion
Two sizes are available:
970213 - 2Mbyte (32pins)
970331 - 8Mbyte (44pins)
VIDEO CN4
CN6 - to Power Supply
CN17
LCD
Ground Connection
or Mixer Board CN6
ANALOG DISP3
OUTPUTS
2MB
POWER
HARD DISK
Supply Board
SIMM DRAM Expansion Slots,
These modules must be two as:
1M x8 or x9 70nS 30-pins
CN10
4M x8 or x9 70nS 30-pins
CN8
DRIVER only 4Mx2 are available from
2MB DRAM
CN9
Generalmusic as code 970225
CPU
FPGA FLOPPY
DISK CN10 - to 3.5" Disk Drive
CNTRL
KBD
KBD SUPPLY
CN15
CN11 VIDEO
CN13
17 ❏
CN3
FROM/TO CPU & SOUND GENERATOR BOARD CN13
D27 33 34 D20
D19 31 32 D28
D26 29 30 D21
D18 27 28 D29 +5V
100E
D25 25 26 D22
ADDR & DATA BUS
D17 23 24 D30
D24 21 22 D23
R14
IC4 MAX709
D16 19 20 D31 1 NC VCC 2
RESET
A1 17 18 4 NC RST 7 +5V
10N
15 16 5 NC GND 3
13 14 6 NC 6
NC 8
C16
4K7 X4
AR5-C
11 12
+5V 9 10 5
7 8
4K7
47P
C2 47P
5 6
3 4
R20
C42
DTACK2 1 2
+5V
FROM/TO CPU & SOUND GENERATOR BOARD CN4
J1 IDMA
CN1 BOOT
ADC & CONTROL SIGNALS
15 EPROM
16 A19 BOOT
13
14 A20 IC17-A ADSP2181
11 D16 122
12 A21 IAD0 BMODE 39
9 D17 121
10 R/W IAD1 MMAP 36
LGND 7 D18 120
8 IAD2 R24 33E
5 D19 119 68
6 SDMA-IN IAD3 EINT +5V
CS3 3 D20 118 70 1 2
4 SDMA-CK IAD4 BR
SDMA-C1 1 D21 117
2 SDMA-C0 IAD5 BG 72 AR5-A
D22 114 4K7 X4
IAD6 EBG 71
D23 113 IAD7 EBR 69
IC1-A 74AC138
A1
1 OF 8 DECODER
A21 3 A2 IAD10 RESET
O2 13 D27 109 61
6 5 CS3 IAD11 ERESET
O3 12 D28 108
6 E3 IAD12 EMS 63
IC3-B 74HC125D D1 4148 O4 11 D29 107
4 5 E2 IAD13 ECLK 65
1 O5 10 D30 106
3 R5 1K 4 IAD14 ELIN 67
2 E1 O6 9 D31 105 IAD15
O7 7
47P
IC10-A A0 15
5 PF0
74HC32 16
A1
C13
R8 1K PF6 22
D2 4148 123 A7
AR3-C PF7 29
33E X4 A8
12 IC10-D 74HC32 6 5 128 IS A9 30
11 AR8-B
13 4 41 IACK A10 31
33E X4 AR8-C
R90 33E 3 1 IAL 32
9 IC10-C 74HC32 A11 33E X4
ADSP2181
8 AR3-D 33E X4 8 7 103 IWR A12 33 5 6
+5V R/W 10
AR3-B 33E X4 4 3 104 IRD A13 34 7 8
5 2 4 3 +5V
9 IC9-C 74HC00 AR8-D
22P
47 FL0 33E X4
8
10 8 48
R7 1K
R6 1K
4K7 X4
C107
IC3-D 74HC125D D0
AR5-D
49 FL2
13 D1 75
1 7
7 8 11 12 AR8-A 33E X4 2 1 50 DT0 D2 76
5 6 1 51 TFS0 D3 77
1 2 IC3-A 74HC125D 3 2 52 RFS0 D4 78
3 4 IC9-A 74HC00 IC2-A 74HC74 57 RFS1/IRQ0 D5 80
2
5 Q CK 3 56 TFS1/IRQ1 D6 81
AR2 33E X4 1 10
2 3 5 4 3 54 SCLK0 D7 82
8 9 D FF
6 Q D 2 60 SCLK1 D8 83
AC1 47P X4 IC3-C 74HC125D 35
S R +5V IRQE D9 84
4 1 55 DT1/F0 D10 85
1
59 DR1/F1 D11 86
53 DR0 D12 87
IC6-A AD1877
AR7-C 4K7 X4 6 5 38 D13 88
R3 2K2 C6 1U 19 C29 470P IRQ2
VinR CAPR1 18 AR7-B 4K7 X4 4 3 45 D14 89
IRQL0
C34 100N C33 470P D15 93
22N
R9 390E
C30 10U
BGH
AR17-A
4K7 X4
4K7 X4
R36 1M CLK0UT
100E
22N
-18V
R10
C23
R37
XT1 16MHZ
FROM CPU & S.G. BOARD CN12
IC8-A 74HC74
3 CK R11 33E
Q 5
CN5
IC8-B 74HC74 D FF
1 DSPCLK R2 10E 11 CK Q 9 2 D Q 6
CLOCK
100N
100N
100N
16 14 14 14 14
C3 100N
13 10
IC1-B IC3-E IC10-E IC9-E IC2-C
74AC138 74HC125D 74HC32 74HC00 74HC74
C15
C21
C20
C14
8 7 7 7 7
+5V
UNUSED COMPONENTS
100N
100N
100N
100N
100N
100N
100N
14 13 28 43 73 91 115
+5V IC8-C
IC17-B ADSP2181
74HC74
C17
C57
C64
C44
C76
C43
C66
IC2-B 74HC74
11 7 12 25 27 44 58 79 90 92 102 116 127
CK Q 9
D FF IC9-D 74HC00
12 D Q 8 12
11
R S 13
13 10 +18V IC7 7805 +5VC
R92 82E 1 3 L1 47UH
+5V +5V IN OUT
1/2W GND
2 1 4 2 9 4 25
100N
100N
10N
AR20-A
C8 100N
IC6-B
33E X4
4K7 X4
4K7 X4
AR3-A
AR5-B
C4 10N
C7 1U
AD1877
C9 1U
C5 1U
1 2 3 13 16 20 5 24
C12
C11
C10
PCB# 315109
VOCAL PROCESSOR BOARD (PCB#315109)
DRW: BOCCATO DWG: 315109 SCHEMATIC DIAGRAM EQUINOX GENERALMUSIC S.p.A. Italy
DRW BOCCATO DWG# 550164 PCB# 315109 GENERALMUSIC S.p.A. ITALY
CKD RICCOBELLI DSK# 65 PART: 1/1 SCHEMATIC DIAGRAM ALL RIGHTS ARE RESERVED, NO COPIES
CKD: RICCOBELLI DISK: 65 PART: 1/1 Vocal Processor Board Pcb Layout ALL RIGHTS ARE RESERVED, NO COPIES
OR REPRODUCE THIS DOCUMENT WITHOUT
OR REPRODUCE THIS DOCUMENT WITHOUT
VOCAL PROCESSOR BOARD WRITTEN CONSENT BY GENERALMUSIC. APP: PANNELLI REV: 25-05-98 WRITTEN CONSENT BY GENERALMUSIC.
APP. PANNELLI REV: 06-10-98
❏ 18
potentiometer. 120003 * M3x8mm Screw
Test Procedure and Adjustment Press ENTER and ESCAPE simultaneously to return to HARD-
Spare Part List
Legend
Cabinet Assembly
The procedures that follow must be executed subsequently in WARE test menu.
EU =Specify European Version (230Vac) Bottom Assembly
the order specified.
þ Memories and Optional Accessories US =Specify U.S. Version (115Vac) 731009 Gnd-Shield Board (Pcb#315164)
These procedures are not intended to repair a fault but only to
Press DEVICE (F1), the instrument self-test check subsequently 61N =only for model with 61 Notes 31 660455 Bottom Chassis (61N)(1)
check the correct instrument operations after a repairing execu-
the follow devices: SIMM modules (VDRAM), 8Mbyte sample 76N =only for model with 76 Notes 31 660459 Bottom Chassis (76N)(1)
tion. GEM =Specify GEM Brand Version 31 660463 Bottom Chassis (61N)(2)
dram (BDRAM), 3.5" disk drive (FD), SCSI interface (SCSI) and
GM =Specify Generalmusic Brand Version 31 660464 Bottom Chassis (76N)(2)
hard disk (HD) marking with pass all devices checked success-
Test Instruments fully, with np all devices not present, with fault all device
1 =1st Version with Traditional supply circuit 29 652734 Left Side
2 =2nd Version with Switching supply circuit 30 652733 Right Side
þ Dual trace oscilloscope defective. Theoretically all test must be passed, if you have a The 1st and 2nd versions differ only by supply unit and its related circuits, these are also 340357 Spacer For Left & Right Side
þ Digital Multimeter mistake on a device re-check its installation. recognizable by the code imprinted on the rear label, where 1st versions are: 340435 Adhesive Foot
Press ENTER if necessary. 995155 Equinox 61N GEM Brand 230Vac (EU) Top Assembly
Accessories 995156 Equinox 61N Generalmusic Brand 115Vac (US) 40 660454 Top Chassis with “GEM” Logo (61N)(1)
þ Inputs, Dsp and Vocal Processor 995157 Equinox 76N GEM Brand 230Vac (EU) 40 660456 Top Chassis with “GM” Logo (61N)(1)
þ 8Mbyte DRAM module Put MASTER - INPUT - LEVEL sliders to maximum position and 995158 Equinox 76N Generalmusic Brand 115Vac (US) 40 660458 Top Chassis with “GEM” Logo (76N)(1)
þ 2Mbyte DRAM module rotate full clockwise GAIN1 and GAIN2 potentiometer located on and 2nd versions are: 40 660460 Top Chassis with “GM” Logo (76N)(1)
þ 2 x 4Mbyte SIMM DRAM modules the rear side. 995167 Equinox 61N GEM Brand 115-230Vac 40 660465 Top Chassis with “GEM” Logo (61N)(2)
þ 1 Hard Disk Kit Measure a sinusoidal signal at 4Vpp on OUT 1 and OUT 2 outputs 995168 Equinox 61N Generalmusic Brand 115-230Vac 40 660466 Top Chassis with “GM” Logo (61N)(2)
þ 1 Vocal Processor Kit sockets (the 1KHz tone gets out OUT R and L, re-input thru MIC 995169 Equinox 76N GEM Brand 115-230Vac 40 660467 Top Chassis with “GEM” Logo (76N)(2)
þ 1 3.5inch Diskette 1 and 2 by the appropriate cable, pass thru DSPs and finally get 995170 Equinox 76N Generalmusic Brand 115-230Vac 40 660468 Top Chassis with “GM” Logo (76N)(2)
þ 1 SCSI Kit out from OUT 1 and 2).
68 660453 SCSI Slot Closer
þ Read/write JOMEGA ZIP SCSI device Turn off the signal by means SIGNAL (F4).
Ref Code Description 66 652749 Dual Slider Potentiometer Support
65 652748 Octal Slider Potentiometer Support
þ RS232 loopback (terminal 1-2 and 3-5 shorted) Accessories
þ 2 jack-jack cables with a resistor divider inside plugs (10K/ þ Noise level 64 652735 Display Screen
970329 Owner’s Manual (English Version) 32 652732 Left-Top Plastic Chassis
82ohm). Turn off the instrument, disconnect the signal cable, wait at least
970328 Owner’s Manual (Italian Version) 41 652731 Right-Top Plastic Chassis
To check completely the keyboard are necessaries all the 30 seconds, turn on again the keyboard and check the noise level 955913 Operating System Disk 340586 Insulant Spacer
optional accessories installed, normally this keyboard have is acceptable (if not verify the insulation between electrical and 955912 Demo Disk 58 340572 Led Light Diffuser
installed from the manufacturer the 2Mbyte DRAM module only. chassis ground is at least 40Kohms). 300617 Owner’s Manual Folder 63 340570 Arrow Actuator
þ Data Hold 130276 Mains Cable (US) 340566 Back-plate for Controls Panel
Setup Press SYSTEM, OTHER (F4), INFO (F1), F4 , ENTER and DHOLD
130274 Mains Cable (EU) 340556 Polycarbonate Washer for Dial
340542 Controls Lower Spacer
Install all the optional accessories: Hard disk and its 2Mbyte (F2) and then wait until the display show PASS. Optional Accessories 340521 Dial Support
module (CN9), 8Mbyte module instead the pre-installed 2Mbyte Turn off the keyboard and then remove not included optional kits 970124 Carring Bag (61N) 62 340493 Dial Knob
module on Sample Dram connector CN5, the 2 SIMM modules, (the EQUINOX base version is equipped with 2Mbyte SAMPLE 970125 Carring Bag (76N) 56 340372 Led Light Diffuser for Actuator
the SCSI and the Vocal processor kits, insert the diskette into DRAM only), restore the jumpers positions: J1 to A, J2 to 2MB, 970110 X-Metal Stand 61 340370 Contrast Knob
3.5" disk drive. JP1 & 2 to B. Turn on again the instrument and verify, repeating 970300 50+50W Amplified Stand (EU) 57 340369 6x15mm Push Cap
Set the jumpers on CPU board as follow: J1 at position B and J2 the test, that only BDRAM pass. 970311 50+50W Amplified Stand (US) 59 340368 6x8mm Push Cap
970116 Single Foot Switch 67 340367 Slider Knob
at position 8MB.
þ Final 970080 Triple Foot Switch 60 340365 “Enter/Escape” Push Cap
Set the JP1 and JP2 jumpers on Supply or Mixer board at position
Verify the keyboard correct operation playing something on it, 970134 Piano Single Foot Switch 340186 Adhesive Cable Fixing
A.
and finally launch the Sounds sequence pressing PROGRAM, 970107 Volume Pedal 340092 5mm Board Spacer
Connect the R and L outputs to the MIC/LINE inputs using the
SHUFFLE (F4), MAKE (F1). When it is finished you have tested 970084 Dynamic Pedalboard 10 171583 3 Din Sockets Reinforcement
appropriate cable. 130301 2mt Midi Cable 8 171472 Analog I/O Board Support
the keyboard.
Connect the external JOMEGA ZIP SCSI device to the SCSI 970310 Multimedia Kit 11 171454 Controls Interface Board Support
socket. þ Reliability Check 130429 * 3mt RS232 Cable (MiniDin 8 To D-Sub 9) 13 171451 4 Jack Sockets Reinforcement
Plug the RS232 loopback into the socket. Before reassembling the instrument and before deliver it to the
970207 Hard Disk Installation Kit 9 171450 6 Jack Sockets Reinforcement
20 970333 Power Station Kit (970207 included) 171444 “Enter/Escape” Reinforcement
user, it is a goal verify its reliability:
Checks and Adjustments To do that switch it off, or leaving it switched on but operating
761094
561006
*
*
2Mbyte Backed Dram Module
2Gbyte Equinox Hard Disk Unit with Various Contents 12
171438
171424
Controls Panel Spacer
4 Din Sockets Reinforcement
with greatest caution, carefully shake the boards and connec-
þ Aftertouch 17 340905 * Rubber Suspension 171397 Spacer For R-Top Plastic Chassis
tions inside it using an insulated tool (for example the handle of 18 120029 * M3x6mm Screw 171396 Spacer For L-Top Plastic Chassis
To adjust the keyboard aftertouch locate the VR1 trimmer on
the screwdriver) to find wrong contacts and so on. 19 120451 * M3 Washer 171004 Right Disk Drive Support
CPU board, connect the scope CH1 probe tip to its center
Turn on the instrument and verify that it operates correctly 22 970213 2Mbyte Backed Samples Dram 171003 Left Disk Drive Support
terminal, probe clip connected at ground, adjust VR1 to obtain 23 970331 8Mbyte Backed Samples Dram 120960 Dial Steel Sphere
repeating the Final Check.
an excursion from 0 to 5V every time a note key is pressed with 16 970330 SCSI Interface Kit 35 110400 3.5" Disk Drive
Disconnect the instrument from the mains, reassemble it and
different pressure, or to obtain a better adjustment follow the 21 970225 Volatile SIMM Dram 39 110254 Rotary Encoder With Snap
shake it carefully without causing aesthetics damages, re-
instructions on ADJUSTMENT TABLE (page 8). 100742 * 4MByte SIMM Module
connect it to the mains, turn on and re-check its functionality, 24 970334 Vocal Processor Kit
Mains Filter & Transformer Assembly (1)
þ MIDI, RS232 and RS422 mode finally leave it switched on for a long time verifing its function- 841152 * 34 Wires 5cm Length Flat Cable 730681 Mains Switch Assembly
Press MIDI, MASTER (F3), PC I/O (F3), set PC1 with DIAL and ality occasionnally. 841030 * 16 Wires 5cm Length Flat Cable 69 340359 ** Power Switch Frame
press ENTER, set LOCAL to OFF (F1), verify that the keyboard 840202 * 9 Wires 10cm Length Flat Cable 171008 ** Mains Socket & Power Switch Support
plays thru RS232 by unplugging and re-inserting the RS232 841025 * 2 Wires 10cm Length Screened Cable 1 110614 ** Mains Socket
761093 * Buffer Module Board (Pcb# 315023) 2 110285 ** Power Switch
loopback into the socket.
103013 ** 74HC138D SOIC 1 Of 8 Decoder 4 767988 Mains Filter Board (Pcb#315014) (EU) (1)
Press MIDI and F3 twice, rotate the DIAL to set MACINTOSH, 103003 ** 74HC374DW SOIC Octal D-Type Flip-Flop 4 768006 Mains Filter Board (Pcb#315014) (US) (1)
check the 1MHz clock appear on pin 1 of COMPUTER socket (use 761167 * Vocal Processor Board (Pcb# 315109) 230568 * 10mH 250Vac 1A AC Line EMI Coil “Siemens”
the second probe tip to do that). 230561 ** 47uH 10% 100mA RF-Coil 140010 * 3 Contacts P=10 Vert Terminal Block
þ Panel Key and Led 141016 ** 16 Contacts Vert Female Connector 110113 * Fuse Clip 5x20mm 6A max (EU)
140917 ** 2 Contacts Vert Male Connector 110114 * Fuse Clip 6.3x32mm 10A Max (US)
Press SYSTEM, OTHER (F4), INFO (F1) and F4 the display show 140866 ** 34 Contacts Vert Male Connector 020493 * 100n 250Vac MKP EMI Capacitor “Siemens”
a warning message: press ENTER and PANEL (F3) and then press 140324 ** 9 Contacts Vert Male Connector 010545 * 4n7 250V Ceramic Capacitor (Iec-Ul-Csa)
all the panel buttons checking their operation on display, at the 106003 ** MAX709 Power Monitor With Reset 5 230127 Transformer 230Vac 120W (EU) (1)
same time every led of pressed button must light up, except 105010 ** ADSP2181 Dsp Microcomputer 5 230129 Transformer 115Vac 120W (US) (1)
DISK led. 103031 ** 74HC00D SOIC Quad Nand Gate 110011 T1A Fuse 5x20mm (EU) (1)
103030 ** 74HC32D SOIC Or Nand Gate 110083 T2A Fuse 6.3x32mm (US) (1)
þ Pitch Bend and Modulation Wheels 103012 ** 74HC125D SOIC Quad Tri-State Buffer
Rotate the Modulation wheel verifying the excursion displayed, 103011 ** AD1877 SOIC Dual Channel 1bit ADC
Power Supply Board (1)
it ranges from 0 to 127. 103007 ** 74HC74D SOIC Dual Flip-Flop 6 730993 Power Supply Board (Pcb#315116) (1)
Rotate the Pitch Bender wheel verifying the excursion displayed, 101500 ** 74AC138D SOIC 1 Of 8 Decoder 230524 * 100uH Switching Coil
it ranges from 0 to 127 with 64 on center position, a slightly 100059 ** 7805 +5V 1A Voltage Regulator 141015 * 14 Contacts Vert Female Connector
difference may be adjusted by VR11 on Controls panel board, 081000 ** PMLL4148 Smd 100mA 75V Signal Diode 141010 * 4 Contacts Vert Female Connector
271230 * Vocal Processor Owner’s Manual Addendum 140874 * Single In Line Vert Male Strip (specify contacts)
major differences may be adjusted repositioning the knob or the
19 ❏
140873 * 4 Contacts Vert Male Connector 340211 *** 12 Dual Contact Rubber Strip 100618 ** 74HC14 Hex Inverter Schmitt Trigger 840707 3 (of 4) Wires 50cm Length Crimp Terminal Cable (61N)(2)
140325 * 12 Contacts Vert Male Connector 141018 *** 20 Contacts Vert Female Connector 100035 ** 6N138 Optocoupler 840607 3 (of 4) Wires 15cm Length Crimp Terminal Cable (76N)(1)
140324 * 9 Contacts Vert Male Connector 141016 *** 16 Contacts Vert Female Connector 090194 ** BC560 TO92 LN Pnp Transistor 840676 3 (of 4) Wires 60cm Length Crimp Terminal Cable (76N)(2)
140323 * 6 Contacts Vert Male Connector 080103 *** 1N4148 100mA 75V Signal Diode 090183 ** BC550 TO92 LN Npn Transistor 840529 16 Wires 20cm Length Flat Cable
140010 * 3 Contacts P=10 Vert Terminal Block 810553 ** 32 Contacts Left Board (Pcb#310535) (61N) 080103 ** 1N4148 100mA 75V Signal Diode 840256 12 Wires 20cm Length Flat Cable
110305 * Relay 12V / 2 Switch 1A 250V 810556 ** 32 Contacts Left Board (Pcb#310565) (76N) 15 110300 * 4.8V 280mAh Nicd Battery 840162 6 Wires 50cm Length Flat Cable (61N)(1)
110119 * Fuse Clip 10A max (EU) (US) 340211 *** 12 Dual Contact Rubber Strip 840160 6 Wires 40cm Length Flat Cable (61N)(2)
100955 * LM2576 5V 3A Switching Regulator 141016 *** 16 Contacts Vert Female Connector
Analog I/O Board 840164 6 Wires 60cm Length Flat Cable (76N)
100906 * CEM3381 Dual V.C.A. 080103 *** 1N4148 100mA 75V Signal Diode 7 730990 Analog I/O Board (Pcb#315163) 841198 6 Wires 7.5cm Length Crimp Terminal Cable (2)
100061 * TL072 Dual J-Fet Operational Amplifier 500073 ** Mechanical Parts (61N) 230569 * FL5R200PNT EMI Coil For Signal 3 770775 Mains Cables Assembly (1)
100045 * 7812 +12V 1A Voltage Regulator 500076 ** Mechanical Parts (76N) 141015 * 14 Contacts Vert Female Connector 3 770852 Mains Cables Assembly (2)
100043 * 7912 -12V 1A Voltage Regulator 160215 *** Key Return Spring 140217 * Jack Stereo Slim Horizontal Socket
090183 * BC550 TO92 LN Npn Transistor 151216 *** First E Key (76N) 140207 * Jack Horizontal Female Socket
090153 * BC327 TO92 Pnp Transistor 151215 *** Last G Key (76N) 100919 * MC33078 Dual LN Operational Amplifier
090152 * BC337 TO92 Npn Transistor 55 151213 *** Last C Key (61N) 080103 * 1N4148 100mA 75V Signal Diode
080606 * GBU8D 8A Rectifier Diodes Bridge 54 151212 *** Sharp Key 070613 * 2X10KC Potentiometer
080171 * FE6B 6A 100V Fast Recovery Diode 53 151211 *** B Key
080103 * 1N4148 100mA 75V Signal Diode 52 151210 *** A Key
Cpu & Sound Generator Board
030950 * 470u 16V 20% Low Esr Vert Electrolytic Capacitor 51 151209 *** G Key 25 761182 Cpu & Sound Generator Board (Pcb#315150)
030554 * 4700u 35v 20% Snap-In Electrolytic Capacitor 50 151208 *** F Key 230527 * BL02RN2-R62 EMI Coil For Signal
110021 T5A Fuse 6.3x32mm (US) 49 151207 *** E Key 141018 * 20 Contacts Vert Female Connector
110020 T5A Fuse 5x20mm (EU) 48 151206 *** D Key 141016 * 16 Contacts Vert Female Connector
47 151205 *** C Key 141011 * 6 Contacts Vert Female Connector
Mains Filter & Switching Supply Assembly (2) 141010 * 4 Contacts Vert Female Connector
730681 Mains Switch Assembly
Pitch & Modulation Assembly 140922 * 32 Contacts Vert Male Strip P=2mm
69 340359 ** Power Switch Frame 34 720553 Pitch & Modulation Assembly 140917 * 2 Contacts Vert Male Connector
171008 ** Mains Socket & Power Switch Support 840726 * 9 Wires 40cm Length Flat Cable 140915 * 44 Contacts Vert Male Strip P=2mm
1 110614 ** Mains Socket 46 340568 * Wheel 140913 * Simm Socket 30 Pin
2 110285 ** Power Switch 340331 * Sheath For Spring 140877 * Jumper For Contacts Strip (p=2.54mm)
45 230532 EMI Choke Coil (2) 210264 * Black Felt 140874 * Single In Line Vert Male Strip (specify contacts)
44 731011 SNP9541M 40W Switching Supply Unit (2) 171460 * Wheel Support 140873 * 4 Contacts Vert Male Connector
110010 T2A Fuse 5x20mm (EU) (US) (2) 160166 * Return Spring 140866 * 34 Contacts Vert Male Connector
120554 * Lock Washer 140854 * 16 Contacts Vert Male Connector
Mixer Board (2) 33 074700 * 4K7 Linear Rotative Potentiometer 140325 * 12 Contacts Vert Male Connector
43 731016 Mixer Board (Pcb#315151) (2) 106003 * MAX709 Power Monitor With Reset
141102 * 6 Contacts Vert Male Connector
Controls Panel Board 105009 * DISP3 QFP Digital Sound Processor (Hitachi)
141015 * 14 Contacts Vert Female Connector 36 810669 Controls Panel Board (Pcb#315153) 105005 * FPGA - Video/Lcd Controller
141010 * 4 Contacts Vert Female Connector 141018 ** 20 Contacts Vert Female Connector 105004 * MC68360EM25 QFP Cpu
140877 * Jumper For Contacts Strip (p=2.54mm) 141016 ** 16 Contacts Vert Female Connector 104039 * KM23C64000G 64Mbit Rom “System”
140874 * Single In Line Vert Male Strip (specify contacts) 141013 ** 10 Contacts Vert Female Connector 104036 * MX23C6410 64Mbit Rom “Samples2”
140873 * 4 Contacts Vert Male Connector 140529 ** Microswitch 12V 50mA 0.25mm 104035 * MX23C6410 64Mbit Rom “Samples1”
140325 * 12 Contacts Vert Male Connector 140328 ** 9 Contacts Hor Male Connector 104020 * KM62256CLG SOP 256Kbit SRam Ta=55nS
140324 * 9 Contacts Vert Male Connector 100620 ** 74HC86 Quad 2-Input Exor Gate 104010 * HM514280AJ 4M5bit Dram Ta=70nS
140323 * 6 Contacts Vert Male Connector 100614 ** 74HC74 Dual Flip-Flop 104009 * HM5118160ALJ 16Mbit Dram Ta=70nS
110305 * Relay 12V / 2 Switch 1A 250V 100607 ** 74HC164 8bit S To P Shift Register 104007 * E28F016SV-70 1Mbit Flash Memory Ta=70nS
100906 * CEM3381 Dual V.C.A. 100061 ** TL072 Dual J-Fet Operational Amplifier 103012 * 74HC125D SOIC Quad Tri-State Buffer
100061 * TL072 Dual J-Fet Operational Amplifier 090183 ** BC550 TO92 LN Npn Transistor 103010 * 74HC04D SOIC Hex Inverter
090183 * BC550 TO92 LN Npn Transistor 080711 ** 3mm High Efficiency Red Led 103009 * 74HC02D SOIC Quad 2-In Nor Gate
090153 * BC327 TO92 Pnp Transistor 080103 ** 1N4148 100mA 75V Signal Diode 103004 * AD1865R SOP 18bit D/A Converter
090152 * BC337 TO92 Npn Transistor 070702 ** 5K Linear Rotary Potentiometer 103002 * 74HC245DW SOIC Octal Bus Transceiver
080103 * 1N4148 100mA 75V Signal Diode 070554 ** 10K Lin. Slider Potentiometer 103001 * 74HC08D SOIC Quad 2-Input And Gate
101506 * 74AC04D SOIC Hex Inverter Gate
Phones Board Controls Interface Board 101502 * 74AC125D SOIC Quad Tri-State Buffer
28 730678 Phones Board (Pcb#315118) 37 761169 Controls Interface Board (Pcb#315113) 100904 * LM393 Dual Comparator
230569 * FL5R200PNT EMI Coil For Signal 141018 * 20 Contacts Vert Female Connector 100733 * uPD72064 Floppy Disk Controller
140361 * 6 Contacts Vert Male Pass-Thru Connector 141016 * 16 Contacts Vert Female Connector 100731 * DS1202 Clock Calendar
140217 * Jack Stereo Slim Horizontal Socket 141013 * 10 Contacts Vert Female Connector 100059 * 7805 +5V 1A Voltage Regulator
140854 * 16 Contacts Vert Male Connector 100058 * 7905 -5V 1A Voltage Regulator
Keyboard Assembly 140325 * 12 Contacts Vert Male Connector 091000 * BC847 TO236 Smd Npn Transistor
720554 61N Keyboard Assembly with Interface 100740 * HD6433278 Cpu F=20MHz 090153 * BC327 TO92 Pnp Transistor
720555 76N Keyboard Assembly with Interface 100645 * 74HC4351 8ch Analog Multiplexer 090152 * BC337 TO92 Npn Transistor
840808 * 16 Wires 30cm Length Flat Cable 100605 * 74HC125 Quad 3-State Buffer 081000 * PMLL4148 Smd 100mA 75V Signal Diode
840807 * 16 Wires 20cm Length Flat Cable (61N) 090183 * BC550 TO92 LN Npn Transistor 080156 * 1N4002 1A 100V Rectifier Diode
841064 * 2 Wires 17cm Length Crimp Terminal Cable (76N) 090153 * BC327 TO92 Pnp Transistor 010732 * 4.194304MHz Quartz Oscillator
840838 * 20 Wires 15cm Length Flat Cable (76N) 080103 * 1N4148 100mA 75V Signal Diode 010727 * 45.1584MHz Quartz Resonator
27 761059 * Keyboard Interface Board (Pcb#315024) (61N) 010725 * 20MHz Ceramic Resonator With Capacitors 010725 * 20MHz Ceramic Resonator With Capacitors
27 761137 * Keyboard Interface Board (Pcb#315024) (76N) 010718 * 32MHz Quartz Resonator
230569 ** FL5R200PNT EMI Coil For Signal
Lcd Display Assembly 010710 * 32768Hz Quartz Resonator
141018 ** 20 Contacts Vert Female Connector 38 730992 Lcd Display Assembly 560019 * 20V8AS-15HB1 Programmed GAL
141016 ** 16 Contacts Vert Female Connector 340456 * Led Spacer
141011 ** 6 Contacts Vert Female Connector 315157 * Lcd Adapter Printed Circuit Board
Wiring Connections
140890 ** 4 Contacts Hor Male Single-Strip 141018 * 20 Contacts Vert Female Connector 841187 20 Wires 20cm Length Flat Cable with Ferrite
140872 ** 4 Contatcs Hor Male Connector 140874 * Single In Line Vert Male Strip (specify contacts) 841150 14 Wires 17.5cm Length Flat Cable
Note:
140918 ** 2 Contacts Hor Male Connector 080754 * LMC97S005A Lcd Display 128X64 dots 841079 16 Wires 12.5cm Length Flat Cable Each spare part is single quantity unless otherwise specified.
100740 ** HD6433278 Cpu F=20MHz 841070 34 Wires 80cm Length Flat Cable Asterisk prefix explanation:
100605 ** 74HC125 Quad 3-State Buffer
Controls & Midi I/O Board 840848 3 (of 4) Wires 30cm Length Crimp Terminal Cable (61N) Omitted = First level spare part.
090194 ** BC560 TO92 LN Pnp Transistor 14 761101 Controls & Midi I/O Board with Battery 840707 3 (of 4) Wires 50cm Length Crimp Terminal Cable (76N) One asterisk = Second level, part of previous listed first level part.
010725 ** 20MHz Ceramic Resonator With Capacitors 751101 * Controls & Midi I/O Board (Pcb# 315088) 840838 20 Wires 15cm Length Flat Cable Two asterisk = Third level, part of previous listed second level part.
26 730680 * Connection Board (Pcb#315114) (76N) 230569 ** FL5R200PNT EMI Coil For Signal 840828 20 Wires 7.5cm Length Flat Cable Three asterisk = ............
140918 ** 2 Contacts Hor Male Connector 141018 ** 20 Contacts Vert Female Connector 840823 10 Wires 10cm Length Flat Cable Any request for not above mentioned part must encompass specific description including:
140890 ** 4 Contacts Hor Male Single-Strip 140247 ** 8 Poles Mini Din Female Socket 840806 12 Wires 5cm Length Crimp Terminal Cable 1) Model name,
720556 * Keyboard Assembly (61N) 140217 ** Jack Stereo Slim Horizontal Socket 840775 6 Wires 20cm Length Flat Cable (61N) 2) Section name,
720557 * Keyboard Assembly (76N) 140216 ** 6 Poles Din Horizontal Female Socket 841164 6 Wires 7.5cm Length Flat Cable (76N) 3) Module code,
810554 ** 29 Contacts Right Board (Pcb#310536) (61N) 140212 ** 5 Poles Din Horizontal Female Socket 840738 4 Wires 5cm Length Flat Cable 4) Reference name,
810557 ** 44 Contacts Right Board (Pcb#310566) (76N) 100734 ** MAX202E RS232 Drivers/Receiver 840587 3 (of 4) Wires 40cm Length Crimp Terminal Cable (61N)(1) 5) Quantity number.
❏ 20