Академический Документы
Профессиональный Документы
Культура Документы
F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
I took the headlight switch out of my stock US spec 328xi and modified it to add rear fog lights.
The button hardware, the lighting circuit and the button are all in the switch assembly, there
are just little plastic tabs that are preventing the button from moving. After modifying the
button you just need to code 5 new values to tell the car what to do with the new button and
everything will work perfectly.
The first step is to pull the left vent out of the car, basically you just grab it and pull it out.
Next remove the headlight panel, there are little clips that you have to pinch while pulling the
panel out at the same time, there are no clips on the bottom, the panel will tip out from the
top. The clips are circled in red.
http://f30.bimmerpost.com/forums/showthread.php?t=877278 1/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
Once you have the switch out pull the wires out of the back, there is no button or catch, just
pull them out. Then you need to remove the back of the switch, there are 6 clips that you need
to release while simultaneously pulling the back off. The clips are circled in red below.
http://f30.bimmerpost.com/forums/showthread.php?t=877278 2/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
http://f30.bimmerpost.com/forums/showthread.php?t=877278 3/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
After you have removed the back you have to pop the button out of the switch assembly. Do
this by pinching the four clips circled in red below and pushing the button out of the front.
http://f30.bimmerpost.com/forums/showthread.php?t=877278 4/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
Now that you have the button out you need to cut the retaining tabs off and smooth everything
out. The tabs are circled in the pictures below. I used a box cutter to cut most of the tab off,
then used a small flathead screwdriver to smooth everything out. It doesn't look pretty, but it
works, and no one will ever see it, so it doesn't matter.
http://f30.bimmerpost.com/forums/showthread.php?t=877278 5/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
http://f30.bimmerpost.com/forums/showthread.php?t=877278 6/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
http://f30.bimmerpost.com/forums/showthread.php?t=877278 7/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
http://f30.bimmerpost.com/forums/showthread.php?t=877278 8/9
7/23/2014 F30 DIY US Headlight Switch Modification for Rear Fog Lights + Coding
After you're all done modifying the button, push it back in the front of the switch, clip the back
of the headlight assembly back on, plug the wires back in, put the panel back into the car, then
put the vent back in.
Now you have to code the button to work, refer to this thread to learn how to code or find
someone in your area to help you. The values you need to code are:
http://f30.bimmerpost.com/forums/showthread.php?t=877278 9/9