Академический Документы
Профессиональный Документы
Культура Документы
CRT4044
DEH-2050MP/XN/ES
CD RECEIVER
DEH-2050MP /XN/ES
DEH-2050MPG/XN/ES
DEH-2050MPG/XN/ES1
This service manual should be used together with the following manual(s):
Model No. Order No. Mech.Module Remarks
CX-3195 CRT3815 S10.5COMP2 CD Mech. Module : Circuit Descriptions, Mech. Descriptions, Disassembly
SAFETY INFORMATION
This service manual is intended for qualified service technicians; it is not meant for the casual do-it-yourselfer.
A Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely
repair complex products such as those covered by this manual.
Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty.
If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so
and refer the repair to a qualified service technician.
Caution:
1. During repair or tests, minimum distance of 13 cm from the focus lens must be kept.
2. During repair or tests, do not view laser beam for 10 seconds or longer.
CAUTION
Danger of explosion if battery is incorrectly replaced.
Replaced only with the same or equivalent type recommended by the manufacture.
C Discord used batteries according to the manufacture's instructions.
DEH-2050MP/XN/ES
2
1 2 3 4
5 6 7 8
Please follow the specified safety methods when modification(addition/change of parts) is required due to interferences such as
radio/TV interference and foreign noise.
When you solder while repairing, please be sure that there are no cold solder and other debris.
Soldering should be finished with the proper quantity. (Refer to the example)
Please be sure that all screws are fastened, and that there are no loose screws.
Please be sure that all connectors are inserted, and that there are no imperfect insertion.
6 Make sure the wiring cables are set to their original state.
Please replace the wiring and cables to the original state after repairs.
In addition, be sure that there are no pinched wires, etc. C
7 Make sure screws and soldering scraps do not remain inside the product.
Please check that neither solder debris nor screws remain inside the product.
8 There should be no semi-broken wires, scratches, melting, etc. on the coating of the power cord.
Damaged power cords may lead to fire accidents, so please be sure that there are no damages.
If you find a damaged power cord, please exchange it with a suitable one.
When spark traces or similar marks are found on the power supply plug, please check the connection and advise on secure
connections and suitable usage. Please exchange the power cord if necessary.
When you perform repairs, please pay attention to static electricity, furniture, household articles, etc. in order to prevent injuries.
Please pay attention to your surroundings and repair safely.
2. Adjustments
To keep the original performance of the products, optimum adjustments and confirmation of characteristics within specification.
Adjustments should be performed in accordance with the procedures/instructions described in this manual.
4. Cleaning
For parts that require cleaning, such as optical pickups, tape deck heads, lenses and mirrors used in projection monitors, proper
cleaning should be performed to restore their performances.
DEH-2050MP/XN/ES
7
3
5 6 8
1 2 3 4
CONTENTS
SAFETY INFORMATION ..................................................................................................................................... 2
1. SERVICE PRECAUTIONS ............................................................................................................................... 5
A
1.1 SERVICE PRECAUTIONS......................................................................................................................... 5
1.2 NOTES ON SOLDERING .......................................................................................................................... 5
2. SPECIFICATIONS ............................................................................................................................................ 6
2.1 SPECIFICATIONS...................................................................................................................................... 6
2.2 DISC/CONTENT FORMAT ........................................................................................................................ 6
2.3 PANEL FACILITIES .................................................................................................................................... 7
2.4 CONNECTION DIAGRAM ......................................................................................................................... 8
3. BASIC ITEMS FOR SERVICE.......................................................................................................................... 9
3.1 CHECK POINTS AFTER SERVICING....................................................................................................... 9
3.2 PCB LOCATIONS .................................................................................................................................... 10
3.3 JIGS LIST ................................................................................................................................................ 11
4. BLOCK DIAGRAM.......................................................................................................................................... 12
B 4.1 BLOCK DIAGRAM ................................................................................................................................... 12
5. DIAGNOSIS.................................................................................................................................................... 16
5.1 OPERATIONAL FLOW CHART ............................................................................................................... 16
5.2 ERROR CODE LIST ................................................................................................................................ 17
5.3 CONNECTOR FUNCTION DESCRIPTION ............................................................................................. 18
6. SERVICE MODE ............................................................................................................................................ 19
6.1 CD TEST MODE ...................................................................................................................................... 19
6.2 CHECKING THE GRATING AFTER CHANGING THE PICKUP UNIT.................................................... 21
7. DISASSEMBLY............................................................................................................................................... 23
8. EACH SETTING AND ADJUSTMENT ........................................................................................................... 26
8.1 PCL OUTPUT CONFIRMATION .............................................................................................................. 26
9. EXPLODED VIEWS AND PARTS LIST.......................................................................................................... 26
C 9.1 PACKING ................................................................................................................................................. 26
9.2 EXTERIOR............................................................................................................................................... 28
9.3 CD MECHANISM MODULE..................................................................................................................... 30
10. SCHEMATIC DIAGRAM ............................................................................................................................... 32
10.1 OVERALL CONNECTION DIAGRAM(GUIDE PAGE)............................................................................ 32
10.2 KEYBOARD UNIT.................................................................................................................................. 38
10.3 CD MECHANISM MODULE(GUIDE PAGE) .......................................................................................... 40
10.4 WAVEFORMS ........................................................................................................................................ 46
11. PCB CONNECTION DIAGRAM ................................................................................................................... 48
11.1 TUNER AMP UNIT................................................................................................................................. 48
11.2 KEYBOARD UNIT.................................................................................................................................. 52
11.3 CD CORE UNIT(S10.5COMP2)............................................................................................................. 54
D
12. ELECTRICAL PARTS LIST .......................................................................................................................... 56
DEH-2050MP/XN/ES
4
1 2 3 4
5 6 7 8
1. SERVICE PRECAUTIONS
1.1 SERVICE PRECAUTIONS
A
- Service Precaution
1. You should conform to the regulations governing
the product (safety, radio and noise, and other
regulations), and should keep the safety during
servicing by following the safety instructions
described in this manual.
2. Before disassembling the unit, be sure to turn off
the power. Unplugging and plugging the connectors
during power-on mode may damage the ICs inside
the unit.
3. To protect the pickup unit from electrostatic discharge B
during servicing, take an appropriate treatment
(shorting-solder) by referring to "the DISASSEMBLY".
4. After replacing the pickup unit, be sure to check the
grating.
5. Be careful in handling ICs. Some ICs such as MOS
type are so fragile that they can be damaged by
electrostatic induction.
For environmental protection, lead-free solder is used on the printed circuit boards mounted in this unit.
Be sure to use lead-free solder and a soldering iron that can meet specifications for use with lead-free solders for repairs
accompanied by reworking of soldering.
D
Compared with conventional eutectic solders, lead-free solders have higher melting points, by approximately 40 C.
Therefore, for lead-free soldering, the tip temperature of a soldering iron must be set to around 373 C in general, although
the temperature depends on the heat capacity of the PC board on which reworking is required and the weight of the tip of
the soldering iron.
Compared with eutectic solders, lead-free solders have higher bond strengths but slower wetting times and higher melting
temperatures (hard to melt/easy to harden).
DEH-2050MP/XN/ES
7
5
5 6 8
1 2 3 4
2. SPECIFICATIONS
2.1 SPECIFICATIONS
A
Backup current
...................................... 2 mA or less
DEH-2050MP/XN/ES
6
1 2 3 4
5 6 7 8
DEH-2050MP/XN/ES
7
7
5 6 8
1 2 3 4
DEH-2050MP/XN/ES
8
1 2 3 4
5 6 7 8
See the table below for the items to be checked regarding video and audio:
DEH-2050MP/XN/ES
7
9
5 6 8
1 2 3 4
C
CD Core Unit(S10.5)
A
Tuner Amp Unit
B
Keyboard Unit
DEH-2050MP/XN/ES
10
1 2 3 4
5 6 7 8
- Jigs List A
- Grease List
Name Grease No. Remarks B
DEH-2050MP/XN/ES
7
11
5 6 8
1 2 3 4
4. BLOCK DIAGRAM
4.1 BLOCK DIAGRAM
A A TUNER AMP UNIT
SYS+B SWVDD
ANTENNA CN401
LDET
REFB
REFA
CE1
1
IFB
IFA
CE2
DO
CK
DI
SL-IN
SLOUT
AM_ANT
2
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
IFOUTA
SLOUT
CE1
RFGND1
RFGND2
RFGND3
RFGND4
VDD
DO
IFOUTB
CE2
LDET
VCC
DI
DGND
REFINA
REFINB
ANT
CK
SLIN
IC2
EEPROM SL-IN
IFA
IFB
REFA
REFB
LDET
DI
B
CK
CE1
DO
VCO LFP CE2
SLOUT
ATT
ATT TANK
IC1
MIX / IF / PLL
ATT RF LFP
ELEC
CF SOU
FM/AM TUNER UNIT
TUNL
C 1
IN1_L
CDL
2
IN2_L
SYSPW
SYSTEM M
COMPUT
IC 601(2
REGULATOR IC PN5012
DEH-2050MP/XN/ES
12
1 2 3 4
5 6 7 8
SYSTEM MICRO
COMPUTER
IC 601(1/2)
PN5013B
SL-IN 62
SL-
IFA 77 IF_INA
CN351
IFB 78 IF_INB RL 2
REFA 96
FREF_A
REFB 97 FREF_B Q351
LDET 99 LOCK
DI 100
DI B
CK 101 CK
CE1 102 CE
DO 103
DO
CE2 109 VST
SLOUT 136 ADIN7 CN901
ACC SENSE 1 1
Q931 B.UP
BACK UP
59 35 ASENS ACC
L_OUT ASENS 3 3
ACC
2 2
GND
ELECTRONIC VOLUME/
SOURCE SELECTOR
FL 23 FL
10 10
7 12 AMP 21
TUNL Rear_L RLIn FL
1
IN1_L
IC 301
PAL007C
FL
3 RL
12 12
FL
C
RL 9 9
6 14 5
Front_L FLIn RL RL
11 11
RL
IC 151
CDL
2
PML014A 22 25 B.REMOTE
IN2_L IN4+_L 4 AUX-L MUTE NC/BREM 6 6
5 AUX-G 6 B.REM
IN4-_L VCC B.UP
4
STBY VCC 20
VCK, VDT, VST
MUTE
Q201(2/2)
SYSTEM MICRO
COMPUTER
IC 601(2/2) MUTE
PN5012B Q201(1/2)
44
POWEROFF MUTE
BSENS D
TOP41
SWVDD
DREG 82
XOUT
X601
81 74.1MHz
XIN
REGC(M)
PLL_VDD
DVDD3 52
AUX IN
1 2
B KEYBOARD UNIT
BU_X1
CN831 CN1801
AUX G
AUX L
DEH-2050MP/XN/ES
7
13
5 6 8
1 2 3 4
RFGND1
RFGND2
RFGND3
RFGND4
IFOUTA
IFOUTB
SLOUT
RFINA
RFINB
DGND
LDET
SLIN
VCC
VDD
ANT
CE1
CE2
DO
CK
A
DI
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20
IC2
EEPROM
VCO LFP
B
ATT
ATT
TANK
IC1
MIX / IF / PLL
ATT RF LFP
CF
DEH-2050MP/XN/ES
14
1 2 3 4
5 6 7 8
- LCD(CAW1930)
E
SEGMENT
COMMON
DEH-2050MP/XN/ES
7
15
5 6 8
1 2 3 4
5. DIAGNOSIS
5.1 OPERATIONAL FLOW CHART
A
Power ON
VDD
Pin 8
bsens
Pin 36
bsens = L
asens
Pin 35
asens = L
C
300 ms
SWVDD H
Pin 1
300 ms
Source ON
SYSPW H
Pin 15
E
DEH-2050MP/XN/ES
16
1 2 3 4
5 6 7 8
the users and also for facilitating trouble analysis and repair work in servicing.
DEH-2050MP/XN/ES
7
17
5 6 8
1 2 3 4
1614 1210 8 6 4 2
1513 11 9 7 5 3 1
C
DEH-2050MP/XN/ES
18
1 2 3 4
5 6 7 8
6. SERVICE MODE
6.1 CD TEST MODE
A
DEH-2050MP/XN/ES
7
19
5 6 8
1 2 3 4
- Flow Chart
[Key] [4] + [6] + Reset or
[4] + [6] + BU + ACC
Contents Test Mode In
A Display
[CD] or [SOURCE]
Source On
C *6
[BAND] [2]
Power Off Tracking Open
*) • After the [Eject] key is pressed keys other than the [Eject] key should not be pressed, until disc ejection is complete.
• When the key [2] or [3] is pressed during the Focus Search, the power supply should be immediately turned off (otherwise the lens
sticks to Wall, causing the actuator to be damaged).
F • In the case of TR jump other than to 100TR, the function shall continue to be processed even if the TR jump key is released. As for
the CRG Move and 100TR Jump, the mechanism shall be set to the Tracking Close mode when the key is released.
• When the power is turned on/off the jump mode is reset to the Single TR (91) while the gain of the RFAMP is reset to 0 dB. At the
same time all the self-adjusting values shall return to the default setting.
DEH-2050MP/XN/ES
20
1 2 3 4
5 6 7 8
Note :
The grating angle of the PU unit cannot be adjusted after the PU unit is changed. The PU unit in the CD mechanism
module is adjusted on the production line to match the CD mechanism module and is thus the best adjusted PU
unit for the CD mechanism module. Changing the PU unit is thus best considered as a last resort. However, if the
PU unit must be changed, the grating should be checked using the procedure below.
Purpose :
To check that the grating is within an acceptable range when the PU unit is changed.
Symptoms of Mal-adjustment : B
If the grating is off by a large amount symptoms such as being unable to close tracking, being unable to perform
track search operations, or taking a long time for track searching.
Method :
Measuring Equipment Oscilloscope, Two L.P.F.
Measuring Points E, F, REFO1
Disc TCD-782
Mode TEST MODE
CD CORE UNIT(S10.5COMP2)
REFO1 C
E F L.P.F.
Xch Ych
E 100 kohm
Oscilloscope
VREF 390 pF
F 100 kohm
VREF 390 pF
L.P.F. D
Checking Procedure
1. In test mode, load the disc and switch the 3 V regulator on.
2. Using the → and ← buttons, move the PU unit to the innermost track.
3. Press key 3 to close focus, the display should read "91". Press key 2 to implement the tracking balance
adjustment the display should now read "81". Press key 3. The display will change, returning to "81" on the
fourth press.
4. As shown in the diagram above, monitor the LPF outputs using the oscilloscope and check that the phase
E
difference is within 75 degrees. Refer to the photographs supplied to determine the phase angle.
5. If the phase difference is determined to be greater than 75 degrees try changing the PU unit to see if there is any
improvement. If, after trying this a number of times, the grating angle does not become less than 75 degrees then the
mechanism should be judged to be at fault.
Note
Because of eccentricity in the disc and a slight misalignment of the clamping center the grating waveform may be
seen to "wobble" ( the phase difference changes as the disc rotates). The angle specified above indicates the
average angle.
Hint
Reloading the disc changes the clamp position and may decrease the "wobble".
DEH-2050MP/XN/ES
7
21
5 6 8
1 2 3 4
0 degrees 30 degrees
45 degrees 60 degrees
75 degrees 90 degrees
DEH-2050MP/XN/ES
22
1 2 3 4
5 6 7 8
7. DISASSEMBLY
While the photograph shown is slightly different from this model in shape, the disassembly procedure is the same.
A
- Removing the Case (not shown)
1. Remove the Case.
4
4 Remove the two screws and then remove
the Tuner Amp Unit.
4
1
1 E
3
3
DEH-2050MP/XN/ES
7
23
5 6 8
1 2 3 4
B
B
A
Damper
D Damper
A
Carriage Mechanism Lower Frame
DEH-2050MP/XN/ES
24
1 2 3 4
5 6 7 8
Screw
CD Core Unit
Solder
Planet Gear
Pickup Rack
Chassis
E
Pickup
DEH-2050MP/XN/ES
7
25
5 6 8
1 2 3 4
- PCL Output
In the normal operation mode (with the detachable panel installed, the ACC switched ON, the standby mode cancelled),
shift the TESTIN IC601(Pin 112) terminal to H. The clock signal is output from the SCET IC601(Pin 43) terminal.
The frequency of the clock signal is 1 Hz. The clock signal should be 1 Hz ± 0.000 04 Hz.
If the clock signal is out of the range, the X'tal (X601) should be replaced with new one.
17
13
16
12
1
15
20
19
18
E
2
9
10
6
11
14
4 5 7
F
DEH-2050MP/XN/ES
26
1 2 3 4
5 6 7 8
DEH-2050MP/XN/ES
7
27
5 6 8
1 2 3 4
9.2 EXTERIOR
25 14
11
A
12
23 42
7
41
1 13
2
2
1 15
39
18
22 17 16
43
1
21
A
B
1
40
A
20 28
40
4
29
A
24 26
44
27
48
58
C
B
56 48
57
55 9
54 64 60
66
63
45 65
61
53 59
62
D
52
3
47 67
46 51
49
50 37 2
33
34
8
38
10
32
35
E 36
5
31
30
DEH-2050MP/XN/ES
28
1 2 3 4
5 6 7 8
31 Spring CBH2367
32 Spring CBH2961
33 Spring CBH2962
34 Cover CNN1665
35 Panel CNS9206
36 Arm CNV9311
37 Arm CNV9312
38 Chassis Unit CXC7391 E
39 CD Mechanism Module(S10.5) CXK5763
40 Screw ISS26P055FTC
41 Transistor(Q991) 2SD2396
42 IC(IC301) PAL007C
43 IC(IC911) BA4918-V12
44 Grille Assy(2050MP/XN/ES) YXA5374
Grille Assy(2050MPG/XN/ES) YXA5367
Grille Assy(2050MPG/XN/ES1) YXA5367
45 Grille Unit(2050MP/XN/ES) YXA5334
Grille Unit(2050MPG/XN/ES) YXA5336 F
Grille Unit(2050MPG/XN/ES1) YXA5336
DEH-2050MP/XN/ES
7
29
5 6 8
1 2 3 4
DEH-2050MP/XN/ES
30
1 2 3 4
5 6 7 8
31 Arm CND2586
32 Bracket CND2587
33 Arm CND2588
34 Lever CND2589
35 Holder CNV7201
36 Gear CNV7207
37 Gear CNV7208
38 Gear CNV7209 E
39 Gear CNV7210
40 Gear CNV7211
41 Gear CNV7212
42 Rack CNV7214
43 Arm CNV7216
44 Roller CNV7218
45 Gear CNV7219
46 Guide CNV7361
47 Gear CNV7595 F
48 Guide CNV7799
49 Arm CNV7805
DEH-2050MP/XN/ES
7
31
5 6 8
1 2 3 4
A-a A-b
Large size
SCH diagram
A-a
C CN701
CD:+0.5dBs
B
FM/AM TUNER UNIT
PDH131A
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
B
discrete resistors. are expressed as : CN1801
Symbol indicates a capacitor. 2.2 t 2R2
No differentiation is made between chip capacitors and 0.022 t R022
discrete capacitors.
A
DEH-2050MP/XN/ES
32
1 2 3 4
5 6 7 8
A-b
A TUNER AMP UNIT
N701
CD:+0.5dBs
FM:-14.33dBs
AM: -25.5dBs
>
>
CEK1208 B.UP
16
10A GND
15
ACC
14
ANT
13
12 B.REM
11
10
TEL
9
RL-
8
FL-
7
6 RL+
5
FL+
RR-
4
FR-
3
RR+
2
FR+
1
A
DEH-2050MP/XN/ES
7
33
5 6 8
F
E
B
A
D
C
34
A-a A-b
A-b
1
1
FM:-14.33dBs
2
2
AM: -25.5dBs
>
DEH-2050MP/XN/ES
3
3
4
4
5
5
>
CEK1208 B.UP
16
10A GND
15
ACC
14
ANT
13
12 B.REM
11
10
TEL
9
RL-
8
FL-
7
6 RL+
5
FL+
RR-
4
FR-
3
RR+
6
6
2
FR+
1
DEH-2050MP/XN/ES
7
7
8
8
A-a A-b
A-b
35
E
A
D
C
F
B
1 2 3 4
A-b
CD:+0.5dBs
CN701
C
C
A-a A-b
D
PDH131A
5
6
6
DEH-2050MP/XN/ES
7
7
NOTE :
Symbol indicates a resistor. Decimal points for resistor
No differentiation is made between chip resistors and and capacitor fixed values
B
discrete resistors. are expressed as : CN1801
Symbol indicates a capacitor. 2.2 t 2R2
No differentiation is made between chip capacitors and 0.022 t R022
discrete capacitors.
8
identical designation.
A-a A-b
A-a
A-b
37
E
A
D
C
F
B
1 2 3 4
GP1UX51RK
100
B
2R2
10K
10
C
1
D1803-D1821
R1803-R1805
R1806,R1807
B
DEH-2050MP/XN/ES
38
1 2 3 4
5 6 7 8
B KEYBOARD UNIT
CLK
4700P
4700P
2R2K
2R2K
YSD5018
100
C
47K
100
A
CN831
D
820
2050MPG/XN/ES
2050MP/XN/ES
2050MPG/XN/ES1
CL-195SR-CD CL-195PG-CD
D1803-D1821 (SUPER RED) (PURE GREEN)
B
DEH-2050MP/XN/ES
7
39
5 6 8
1 2 3 4
A
C-a
PICKUP UNIT(P10.5)(SERVICE)
F
%
T
F
T
F
F
T F F
F F
T T T
T T
C #
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
M1 CXC7134
SPINDLE MOTOR
S
C
$
C
M2 CXC4026
LOADING/CARRIAGE MOTOR T S
9 7
F C
0 8 4
E 5
CD DRIVER
C
DEH-2050MP/XN/ES
40
1 2 3 4
5 6 7 8
A
C-b
C CD CORE UNIT(S10.5COMP2)
!
B
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
A
CN651
^ &
C
DEH-2050MP/XN/ES
7
41
5 6 8
F
E
B
A
D
C
42
C-a C-b
C-b
1
1
C CD CORE UNIT(S10.5COMP2)
2
2
SIGNAL LINE
F
FOCUS SERVO LINE
T
TRACKING SERVO LINE
C
CARRIAGE SERVO LINE
S
SPINDLE SERVO LINE
DEH-2050MP/XN/ES
3
3
4
4
5 6 7 8
CN651
A
A
6
B
&
^
C
C-a C-b
D
2 3 C-b
DEH-2050MP/XN/ES
7
43
5 6 8
F
E
B
A
D
C
44
C-a C-b
C-a
C-b
1
1
PICKUP UNIT(P10.5)(SERVICE)
2
2
F
%
DEH-2050MP/XN/ES
T
F
3
3
T
F
F
T F F
F F
T T T
T T
4
4
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
SWITCHES:
CD CORE UNIT(S10.5COMP2)
S901:HOME SWITCH..........ON-OFF
S903:DSCSNS SWITCH......ON-OFF
S904:12EJ SWITCH.............ON-OFF
S905:8EJ SWITCH...............ON-OFF
The underlined indicates the switch position.
5
5
M1 CXC7134
SPINDLE MOTOR
2
C
$
C
M2 CXC4026
6
6
LOADING/CARRIAGE MOTOR T S
9 7
F C
0 8 4
DEH-2050MP/XN/ES
2
7
7
CD DRIVER
3
8
8
C-a c-b
C-a
C-b
45
E
A
D
C
F
B
1 2 3 4
10.4 WAVEFORMS
- CD Core Unit Note : 1. The encircled numbers denote measuring points in the circuit diagram.
2. Reference voltage REFO1(1.65 V)
A
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div
28SNS 5 V/div 5CLCONT 5 V/div 28SNS 5 V/div
312SNS 5 V/div 4LOEJ 5 V/div 312SNS 5 V/div
4LOEJ 5 V/div 6VD 10 V/div 4LOEJ 5 V/div
12 cm CD Loading operation 12 cm CD Loading operation 8 cm CD Loading operation
7SIN 1 V/div 1 s/div 0FIN 200 mV/div 500 ms/div @TE 500 mV/div 200 ms/div
8CIN 500 mV/div !RFOK(MONI_2) 2 V/div #FE 500 mV/div
9TIN 1 V/div 7SIN 2 V/div
12 cm CD-DA setup operation after loading 12 cm CD-DA Source On setup operation Source On setup operation
C
Ref.: Ref.: Ref.:
REFO REFO REFO
#FE 500 mV/div 20 ms/div $MDX 2 V/div 200 ms/div $MDX 2 V/div 5 µs/div
0FIN 500 mV/div 7SIN 500 mV/div 7SIN 500 mV/div
@TE 500 mV/div
9TIN 500 mV/div
D CD-DA Play operation Spindle waveform during play operation Spindle waveform during play operation
(Wider)
0FIN 500 mV/div 200 ms/div @TE 500 mV/div 2 ms/div %RFAGC 1 V/div 500 µs/div
E #FE 500 mV/div %RFAGC 500 mV/div @TE 500 mV/div
9TIN 500 mV/div
DEH-2050MP/XN/ES
46
1 2 3 4
5 6 7 8
%RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 500 µs/div %RFAGC 1 V/div 2 ms/div
@TE 500 mV/div @TE 500 mV/div @TE 500 mV/div A
9TIN 500 mV/div 9TIN 500 mV/div 9TIN 500 mV/div
%RFAGC 1 V/div 200 ms/div ^LOUT 1 V/div 200 µs/div 1DSCSNS 5 V/div 500 ms/div
@TE 1 V/div &ROUT 1 V/div 28SNS 5 V/div
8CIN 1 V/div 312SNS 5 V/div
7SIN 2 V/div 4LOEJ 5 V/div
Search operation(Outter to Inner) Analog audio waveform 12 cm CD Eject operation
1DSCSNS 5 V/div 500 ms/div 1DSCSNS 5 V/div 500 ms/div %RFAGC 1 V/div 500 µs/div
5CLCONT 5 V/div 28SNS 5 V/div 9TIN 1 V/div
4LOEJ 5 V/div 312SNS 5 V/div @TE 1 V/div
4LOEJ 5 V/div 0FIN 1 V/div
12 cm CD Eject operation 8 cm CD Eject operation Black dot(800 µm) during play
DEH-2050MP/XN/ES
7
47
5 6 8
1 2 3 4
B SIDE A
SIDE B
P.C.Board Chip Part
E
C CN701
B CN1801
A
DEH-2050MP/XN/ES
48
1 2 3 4
5 6 7 8
SIDE A
ASSY
RCA OUTPUT
B
ANTENNA
F
FRONT
A
DEH-2050MP/XN/ES
7
49
5 6 8
1 2 3 4
SCET
TESTIN
A
DEH-2050MP/XN/ES
50
1 2 3 4
5 6 7 8
SIDE B
A
DEH-2050MP/XN/ES
7
51
5 6 8
1 2 3 4
A
B KEYBOARD UNIT SIDE A
EJECT
6
5
B
4
3
C
2
1
D
AUDIO
EQ
SOURCE/VOL
E
FUNC
BAND
DISP
CLK
B
DEH-2050MP/XN/ES
52
1 2 3 4
5 6 7 8
A
CN831
B
DEH-2050MP/XN/ES
7
53
5 6 8
1 2 3 4
A
C CD CORE UNIT(S10.5COMP2) SIDE A
E
M2
LOADING
/CARRIAGE
MOTOR
M1
SPINDLE
MOTOR
C
DEH-2050MP/XN/ES
54
1 2 3 4
5 6 7 8
C
DEH-2050MP/XN/ES
7
55
5 6 8
1 2 3 4
A
L 610 (A,140,67) Inductor LAU1R2J
DEH-2050MP/XN/ES
56
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
R 203 (B,125,131) RS1/16S221J R 821 (B,27,13) RS1/16S562J
R 251 (B,104,106) RS1/16S223J R 822 (B,27,11) RS1/16S103J
R 252 (B,137,101) RS1/16S223J R 831 (B,36,12) RS1/16S1R0J
R 832 (B,86,26) RS1/16S473J A
R 301 (B,95,107) RS1/16S153J R 833 (A,81,23) RD1/4PU222J
R 351 (B,166,131) RS1/16S223J
R 352 (B,166,135) RS1/16S223J R 834 (A,83,23) RD1/4PU222J
R 353 (B,147,118) RS1/16S821J R 835 (A,62,21) RD1/4PU222J
R 354 (B,165,126) RS1/16S821J R 837 (A,77,19) RD1/4PU103J
R 839 (A,89,14) RD1/4PU222J
R 404 (B,157,44) RS1/16S102J R 840 (A,86,14) RD1/4PU222J
R 405 (B,161,54) RS1/16S102J
R 406 (B,161,60) RS1/16S102J R 841 (B,75,27) RS1/16S104J
R 407 (B,161,62) RS1/16S102J R 855 (B,81,67) RS1/16S104J
R 408 (B,169,50) RAB4C104J R 873 (B,140,24) RS1/16S103J
R 874 (B,140,31) RS1/16S103J
R 409 (B,161,47) RS1/16S391J R 931 (B,106,40) RS1/16S104J B
R 410 (B,161,49) RS1/16S681J
R 411 (B,161,51) RS1/16S681J R 932 (B,62,100) RS1/16S223J
R 412 (B,161,53) RS1/16S681J R 933 (A,70,106) RD1/4PU102J
R 413 (B,161,56) RS1/16S472J R 934 (B,67,113) RS1/16S472J
R 935 (B,62,115) RS1/16S473J
R 601 (B,125,28) RS1/16S473J R 991 (A,14,116) RD1/4PU271J
R 603 (B,108,40) RS1/16S473J
R 606 (B,109,70) RS1/16S473J
R 608 (B,141,60) RS1/16S470J CAPACITORS
R 610 (B,123,64) RS1/16S203J
C 151 (B,109,101) CKSRYB224K10
R 611 (B,139,71) RS1/16S182J C 152 (B,133,95) CKSRYB224K10
R 612 (B,117,75) RS1/16S563J C
C 153 (B,109,104) CKSRYB105K10
R 613 (B,142,52) RS1/16S302J C 154 (B,133,98) CKSRYB105K10
R 615 (B,114,75) RS1/16S563J C 155 (A,126,113) CEJQ470M10
R 616 (B,159,40) RS1/16S104J
C 156 (B,134,101) CKSRYB105K10
R 617 (B,137,32) RS1/16S473J C 157 (B,109,106) CKSRYB105K10
R 618 (B,148,41) RS1/16S473J C 162 (B,134,103) CKSRYB105K10
R 619 (B,149,39) RS1/16S104J C 163 (B,109,108) CKSRYB105K10
R 638 (B,160,88) RS1/16S273J C 164 (A,120,113) CEJQ100M16
R 641 (B,153,37) RS1/16S103J
R 642 (B,151,33) RS1/16S103J C 165 (B,123,112) CKSRYB104K16
C 201 (A,129,134) CEJQ330M10
R 643 (B,159,38) RS1/16S104J C 253 (B,97,104) CKSRYB104K16
R 644 (B,99,67) RS1/16S0R0J D
C 301 (B,126,122) CKSQYB474K16
R 645 (B,101,19) RS1/16S0R0J C 302 (B,122,122) CKSQYB474K16
R 646 (B,160,16) RS1/16S0R0J
R 648 (B,159,74) RS1/16S0R0J C 303 (B,124,122) CKSQYB474K16
R 651 (B,34,30) RS1/16S104J C 304 (B,120,122) CKSQYB474K16
C 305 (B,126,126) CKSRYB474K10
R 652 (B,34,35) RS1/16S102J C 306 (B,122,126) CKSRYB474K10
R 653 (B,34,34) RS1/16S102J C 307 (B,124,126) CKSRYB474K10
R 654 (B,34,32) RS1/16S221J
R 656 (B,107,26) RS1/16S104J C 308 (B,120,126) CKSRYB474K10
R 657 (B,107,28) RS1/16S104J C 309 (B,124,139) CKSQYB225K10
C 310 (B,116,144) CKSQYB225K10
R 658 (B,34,37) RS1/16S104J C 312 (A,101,122) CEJQ100M16 E
R 659 (B,107,30) RS1/16S472J C 313 (B,101,141) CKSRYB104K16
R 660 (B,107,32) RS1/16S472J
R 661 (B,111,28) RS1/16S221J C 353 (A,145,119) CEJQ2R2M50
R 662 (B,111,30) RS1/16S221J C 354 (A,143,112) CEJQ2R2M50
C 359 (B,164,137) CCSQCH471J50
R 663 (B,111,32) RS1/16S221J C 402 (B,142,100) CKSRYB103K50
R 664 (B,79,54) RS1/16S473J C 404 (A,150,97) CEJQ101M10
R 666 (B,168,30) RS1/16S103J
R 671 (B,136,24) RS1/16S473J C 405 (B,146,100) CKSRYB103K50
R 672 (B,110,46) RS1/16S104J C 406 (B,169,53) CCSRCH390J50
C 409 (B,161,45) CCSRCH100D50
R 673 (B,137,27) RAB4C104J C 601 (B,120,27) CKSRYB105K10
R 674 (B,132,27) RS1/16S104J C 602 (B,121,30) CKSRYB103K50 F
R 675 (B,94,59) RS1/16S473J
R 677 (B,122,22) RS1/16S104J C 603 (B,123,28) CKSRYB103K50
R 803 (B,86,18) RS1/16S222J C 605 (B,108,74) CKSRYB104K16
DEH-2050MP/XN/ES
7
57
5 6 8
1 2 3 4
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
C 606 (B,105,56) CKSRYB103K50
C 607 (B,118,55) CKSRYB103K50 MISCELLANEOUS
C 608 (B,95,80) CKSRYB103K50
A IC 1801 (B,26,121) IC PD6340A
C 609 (B,116,72) CKSRYB331K50 IC 1802 (A,10,161) Remote IC GP1UX51RK
C 610 (A,98,80) CEJQ101M6R3 D 1803 (A,14,42) LED CL-195SR-CD
C 611 (B,116,70) CKSRYB331K50 D 1805 (A,15,23) LED CL-195SR-CD
C 612 (B,120,58) CKSRYB103K50 D 1806 (A,12,11) LED CL-195SR-CD
C 613 (A,104,58) CEAL101M6R3
D 1807 (A,41,42) LED CL-195SR-CD
C 614 (B,168,88) CKSRYB102K50 D 1808 (A,28,28) LED CL-195SR-CD
C 615 (B,125,62) CKSRYB331K50 D 1809 (A,35,20) LED CL-195SR-CD
C 616 (B,125,69) CKSRYB105K10 D 1810 (A,22,7) LED CL-195SR-CD
C 617 (B,130,61) CKSRYB105K10 D 1811 (A,36,63) LED CL-195SR-CD
C 618 (B,113,54) CCSRCH270J50
D 1812 (A,41,84) LED CL-195SR-CD
B C 619 (B,144,71) CKSRYB103K50 D 1813 (A,41,97) LED CL-195SR-CD
C 620 (B,144,57) CKSRYB105K10 D 1814 (A,41,111) LED CL-195SR-CD
C 621 (B,152,70) CKSRYB103K50 D 1815 (A,40,124) LED CL-195SR-CD
C 622 (B,142,54) CKSRYB104K16 D 1816 (A,39,138) LED CL-195SR-CD
C 623 (B,134,66) CKSRYB102K50
D 1817 (A,38,151) LED CL-195SR-CD
C 624 (B,131,66) CKSRYB102K50 D 1818 (A,6,149) LED CL-195SR-CD
C 625 (B,137,72) CCSRCH270J50 D 1819 (A,28,55) LED CL-195SR-CD
C 626 (B,131,72) CCSRCH270J50 D 1821 (A,15,61) LED CL-195SR-CD
C 627 (B,136,79) CCSRCH150J50 D 1822 (A,24,74) White LED NESW505C-5273
C 628 (B,143,64) CKSRYB102K50
D 1826 (B,26,151) Diode MALS068X
C 629 (B,136,60) CCSRCH4R0C50 D 1827 (B,31,148) Diode MALS068X
C C 630 (B,144,69) CCSRCH8R0D50 D 1828 (B,28,151) Diode MALS068X
C 631 (B,108,72) CKSRYB223K50 X 1801 (B,31,106) Ceramic Resonator 5.00 MHz CSS1731
C 632 (B,130,23) CKSRYB104K16 S 1833 (A,28,42) Rotary Switch YSD5018
C 633 (B,147,31) CKSRYB104K16
LCD1801 (A,15,149) LCD CAW1930
C 634 (B,113,58) CCSRCH270J50
C 635 (B,147,55) CKSRYB104K16 RESISTORS
C 637 (B,110,77) CKSRYB103K50
C 640 (B,125,60) CKSRYB104K16
R 1801 (B,29,89) RS1/16S222J
C 642 (B,109,103) CKSRYB182K50 R 1802 (B,27,93) RS1/16S222J
R 1803 (B,19,68) RS1/4SA821J
C 643 (B,133,99) CKSRYB182K50
R 1804 (B,24,68) RS1/4SA821J
C 646 (B,116,22) CKSRYB103K50 R 1805 (B,36,96) RS1/4SA821J
D C 652 (B,49,31) CKSRYB103K50
C 653 (B,114,33) CCSRCH220J50
R 1806 (B,36,100) RS1/4SA681J
C 821 (B,36,10) CKSRYB104K16 R 1807 (B,22,68) RS1/4SA681J
R 1809 (B,27,50) RS1/16S473J
C 825 (B,61,8) CCSRCH221J50
R 1810 (B,26,75) RS1/4SA821J
C 826 (B,82,14) CCSRCH221J50 R 1833 (B,23,145) RS1/16S2R2J
C 827 (B,71,8) CCSRCH221J50
C 828 (B,69,8) CCSRCH221J50
R 1835 (B,23,150) RS1/16S101J
C 829 (B,63,8) CCSRCH221J50 R 1836 (B,18,154) RS1/16S103J
R 1837 (B,31,146) RS1/16S101J
C 830 (B,65,8) CKSRYB104K16
R 1838 (B,25,150) RS1/16S101J
C 831 (B,67,8) CCSRCH221J50
C 901 (A,52,114) 3 300 µF/16 V CCH1732
E
C 911 (A,59,62) CEJQ100M16
CAPACITORS
C 912 (A,48,66) CEAT102M16
C 1801 (B,28,133) CKSRYB105K10
C 1803 (B,18,152) CKSYF106Z10
C 913 (B,28,71) CKSRYB104K16
C 1810 (B,23,152) CKSRYB472K50
C 914 (A,52,62) CEAT221M10
C 1811 (B,30,152) CKSRYB472K50
C 915 (A,46,55) CEJQ100M16
C 916 (A,58,55) 1 000 µF/6.3 V CCH1751(P35)
C 917 (B,28,77) CKSRYB104K16
B
Unit Number : (2050MPG/XN/ES)
C 991 (B,11,108) CKSRYB473K25
C 992 (A,12,97) CEJQ101M10 Unit Number : (2050MPG/XN/ES1)
Unit Name : Keyboard Unit
F
B
Unit Number : (2050MP/XN/ES) MISCELLANEOUS
Unit Name : Keyboard Unit IC 1801 (B,26,121) IC PD6340A
DEH-2050MP/XN/ES
58
1 2 3 4
5 6 7 8
Circuit Symbol and No. Part No. Circuit Symbol and No. Part No.
IC 1802 (A,10,161) Remote IC GP1UX51RK X 201 (A,23,35) Ceramic Resonator 16.934 MHz CSS1603
D 1803 (A,14,42) LED CL-195PG-CD S 901 (A,53,37) Switch(HOME) CSN1067
D 1805 (A,15,23) LED CL-195PG-CD S 903 (B,19,58) Switch(DSCSNS) CSN1067
D 1806 (A,12,11) LED CL-195PG-CD S 904 (B,38,67) Switch(12EJ) CSN1068 A
S 905 (B,24,68) Switch(8EJ) CSN1068
D 1807 (A,41,42) LED CL-195PG-CD
D 1808 (A,28,28) LED CL-195PG-CD RESISTORS
D 1809 (A,35,20) LED CL-195PG-CD
D 1810 (A,22,7) LED CL-195PG-CD R 101 (B,60,73) RS1/10SR2R4J
D 1811 (A,36,63) LED CL-195PG-CD R 102 (B,59,71) RS1/10SR2R4J
R 103 (B,60,71) RS1/10SR2R7J
D 1812 (A,41,84) LED CL-195PG-CD R 104 (B,52,69) RS1/16SS222J
D 1813 (A,41,97) LED CL-195PG-CD R 105 (B,41,57) RS1/16SS102J
D 1814 (A,41,111) LED CL-195PG-CD
D 1815 (A,40,124) LED CL-195PG-CD R 107 (B,41,59) RS1/16SS105J
D 1816 (A,39,138) LED CL-195PG-CD R 202 (B,32,62) RS1/16SS473J
B
R 203 (B,42,45) RS1/16S473J
D 1817 (A,38,151) LED CL-195PG-CD R 204 (A,25,61) RS1/16SS221J
D 1818 (A,6,149) LED CL-195PG-CD
D 1819 (A,28,55) LED CL-195PG-CD R 206 (B,26,53) RS1/16SS104J
D 1821 (A,15,61) LED CL-195PG-CD R 210 (B,13,32) RS1/16SS102J
D 1822 (A,24,74) White LED NESW505C-5273 R 214 (B,36,34) RS1/16SS472J
R 216 (B,47,49) RS1/16SS472J
D 1826 (B,26,151) Diode MALS068X R 221 (B,36,32) RS1/16SS103J
D 1827 (B,31,148) Diode MALS068X
D 1828 (B,28,151) Diode MALS068X R 222 (B,35,32) RS1/16SS103J
X 1801 (B,31,106) Ceramic Resonator 5.00 MHz CSS1731 R 225 (A,49,49) RS1/16SS103J
S 1833 (A,28,42) Rotary Switch YSD5020 R 226 (A,49,50) RS1/16SS393J
R 227 (B,45,51) RS1/16SS562J
LCD1801 (A,15,149) LCD CAW1930 C
R 228 (B,42,53) RS1/16SS122J
C
Unit Number : CWX3514
C
C
106
202
(B,56,69)
(A,27,57)
CKSQYB475K6R3
CKSSYB104K10
C 204 (A,24,63) CKSSYB103K16
Unit Name : CD Core C 205 (B,23,43) CKSQYB475K6R3
Unit(S10.5COMP2)
C 206 (A,22,39) CKSSYB104K10
C 207 (A,24,37) CKSRYB104K16
MISCELLANEOUS C 209 (B,33,40) CEVW220M6R3
C 210 (B,29,42) CKSSYB104K10
IC 201 (A,34,46) IC PE5547A C 211 (A,27,34) CKSSYB104K10 F
IC 301 (A,27,14) IC BA5839FP
Q 101 (B,56,72) Transistor 2SA1577 C 212 (B,29,32) CKSRYB104K16
Q 102 (B,47,57) Chip Transistor 2SB1689 C 213 (A,44,37) CKSSYB104K10
DEH-2050MP/XN/ES
7
59
5 6 8
1 2 3 4
DEH-2050MP/XN/ES
60
1 2 3 4