Вы находитесь на странице: 1из 12

Workshop Manual - 5300 Series Tractors 1

Issue 02: 03/03


Section O: General specifications

Workshop Service Manual


MF 5300 Series Tractors

Section O
General Specifications

Issue 02 - 03 / 2003
Contents of this Section:
Engine Brakes ............................................................................................................. 8
Lubrication system: ................................................................................ 4 Hydraulic lift system
Air cleaner ............................................................................................... 4 Ferguson System (Tractors fitted with Platform and Cab) ................... 8
Fuel system ............................................................................................. 4 Boschtronic system operated by levers (platform version only) ......... 9
Electrical system - power and capacities ...................................................... 5 Boschtronic system operated by panel (Cab version only) ................ 9
Clutch .............................................................................................................. 6 Auxiliary hydraulic systems ............................................................................ 9
Gearbox .......................................................................................................... 6 Independent Power-Take-Off: ...................................................................... 11
Theoretical maximum speed on road, in km / h (engine @ 2200 rpm) ...... 7 Tractor weights - in kgf ................................................................................. 11
Rear Axle ......................................................................................................... 7 Tractors general dimensions - in mm .......................................................... 12
Front axle Filling Capacities - in liters ........................................................................... 12

Workshop Manual - 5300 Series Tractors


2 WD axle ................................................................................................ 7 Wheels nuts torques - kgf.m ....................................................................... 13
4 WD axle (Carraro) ................................................................................ 8 Drawbar ......................................................................................................... 13

Section O: General specifications


Cab and air conditioning system (Optional) ............................................... 13
General electric diagram ......................................................... See Section "L"
4

3 2
1

Issue 02: 03/03


3
Fig. 500 Fig. 501
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

4
Issue 02: 03/03
Engine
Make / Model: .............................................................................. Perkins P4001 Perkins P4001 Perkins P4001 T Perkins 4001 T Perkins 1006-6
Aspiration: .................................................................................... Natural Natural Turbo Turbo Natural
Cycle / Injection type: .................................................................. -------------------------------------------------------------- 4-stroke, direct injection ------------------------------------------------------------
Number of cylinders: ................................................................... 4 4 4 4 6

Workshop Manual - 5300 Series Tractors


Firing order: ................................................................................. 1-3-4-2 1-3-4-2 1-3-4-2 1-3-4-2 1-5-3-6-2-4
Valve tip clearance (cold engine) – mm: .................................... Inlet = 0.20 mm - Exhaust = 0.45 mm
Capacity – liters: .......................................................................... 4.10 4.10 4.10 4.10 6.00
Maximum torque @ rpm: - N.m: (ISO14396) ............................ 279 @ 1400 288 @ 1400 348 @ 1400 382 @ 1400 442 @ 1100
Maximum horsepower @ rpm: - cv: (ISO14396) ....................... 79 @ 2200 83.0 @ 2200 92.0 @ 2200 105.0 @ 2200 120.0 @ 2200

Section O: General specifications


Lubrication system:
Pressure-fed, with gear type pump (relief pump built-in). On 4-cylinder engines, the pump is incorporated in the dynamic rocker. Full flow oil filter.
Number of filters: ......................................................................... 1 1 1 1 1
Minimum pressure at maximum rpm – kgf/cm2 : ....................... 2.1 2.1 2.5 2.5 2.1

Air cleaner
Type: ............................................................................................. Two-stage dry air cleaner, with two elements (primary and secondary). Fitted with restriction indicator and warning
light on the instrument panel.
High air cleaning system: ............................................................ Optional. It consists of greater size filter elements, which are recommended for operations in areas under high dusty
conditions. It is also fitted with automatic ejection system, which eliminates the dust via exhaust system.

Fuel system
Fuel pre-filter: ............................................................................... Removable for cleaning; no replacement is required. Located on the right-hand side of engine.
Fuel filters: .................................................................................... Microporous paper type element(s), which must be replaced every 250 hours.
Number of filters: ......................................................................... 1 1 1 1 2
Injection pump: ............................................................................ Located on the right-hand side of engine, it is driven by camshaft lobe. It also incorporates a hand primer to carry out
fuel system bleeding.
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

Injection pump – make / type: .................................................... For all: Lucas / Delphi, horizontal, rotative type
Cooling system – type: ................................................................ For all: Air / water
Radiator: ....................................................................................... For all: Vertical pipes and horizontal fins
Water pump, centrifugal type / driven by: .................................. Pulleys and belt(s) Pulleys and belt(s) Pulleys and belt(s) Pulleys and belt(s) By gears
Thermostatic valve – type / number: .......................................... Wax capsule / 1 Wax capsule / 1 Wax capsule / 1 Wax capsule / 1 Wax capsule / 2
Temperature opening start: ......................................................... For all: 80 to 98 0C
Radiator cap: ................................................................................ Limits the pressure in the cooling system at 7.0 PSI Limits the pressure in the cooling system at 10.0 PSI It also incorporates
a pressure valve, which prevents an air pocket formation when water is cooled.
Oil heat exchanger: ...................................................................... No No Built-in to the lubricating oil filter Left-hand side of

Workshop Manual - 5300 Series Tractors


cylinder block

Section O: General specifications


Electrical system - power and capacities
a) Battery:
MF 5335 to 5360 = 1 battery, 95 Ah
MF 5365 = 2 batteries in parallel, 65 Ah each one
b) Alternator : Tractors without cab = 12.4 V / 55 A Tractors with cab and air conditioner = 14.2V / 70 A
c) Starter motor = 3 kW
d) Front service headlights (main beam) = 45 W
e) Front service headlights (dimmed) = 40 W
f) Cab’s front and rear flood lights and platform’s rear flood lights = 55 W
g) Auxiliary flood lights (platform-equipped tractors) = 48 W
h) Brake lights and directional turn signal lights = 21 W
i) Safety starter switch = standard on all models
j) Fuses = Refer to Section L: Capacity: 10. 15. 20. 25. 30 Amperes, blade-type fuses
k) Rear lanterns = 5 W

Issue 02: 03/03


l) Glow plug (optional – cold starting aid) = 9 A

5
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

6
Issue 02: 03/03
Clutch
13" (330 mm) Split Torque clutch
Application ................................................................................... Standard Optional Optional Optional Optional

Gearbox

Workshop Manual - 5300 Series Tractors


12x4 Speeds Partial-Syncro gearbox
Application ................................................................................... Standard Standard Standard Standard Standard
st nd rd
Control levers: .............................................................................. 2 side control levers: the largest for selection of gears (1 , 2 , 3 gear and Reverse speed) and the smallest for
selection of High & Low Range shift lever and Dual Range selector lever
12x4 Speeds Full-Syncro gearbox

Section O: General specifications


Application ................................................................................... Optional Optional Optional Optional Optional
Control levers: .............................................................................. Idem 12x4 Partial-Syncro.

8x8 Speeds Gearbox


Application ................................................................................... Optional Optional Optional Optional Optional
Controls: ....................................................................................... 1 side control (selects two-speed ranges and main gears), plus 1 lever on instrument panel, left-hand side, which
selects Forward and Reverse.
12x12 Speeds Syncro, Shuttle gearbox
Application ................................................................................... Optional Optional Optional Optional Optional
Controls: ....................................................................................... 1 side control (selects three-speed ranges and main gears), plus 1 lever on instrument panel, left-hand side, which
selects Forward and Reverse.
18x6 Speeds gearbox
Application: .................................................................................. Optional Optional Optional Optional Optional
Type: ............................................................................................. Synchromesh, three Speed Ranges (L - M - H) and with selection of electrohydraulic Fast and Slow speeds.
Controls: ....................................................................................... 1 side control fitted with a push-button on top of of the gear lever knob for selection of Fast and Slow speeds.
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

Theoretical maximum speed on road, in km / h (engine @ 2200 rpm)

☞ NOTE:
For further information on interpretation of travel speed chart to establish the correct gear and engine speed at which to
operate to comply with the job’s requirements, refer to operator´s book.
The speed for each gear depends upon the tractor’s model, the transmission type, the rear wheels and engine speed.
This information you find on the travel speed chart table (See 1 - Fig. 501).
Always consult your tractor’s travel speed chart.

Rear Axle

Workshop Manual - 5300 Series Tractors


Crown and pinion reduction: ...................................................... 3.889 : 1 3.454 : 1 for 18-speed transmission 3.888 : 1 for 12-speed transmission
Differential lock: ........................................................................... Via coupling sleeves: one fixed to the differential carrier and one sliding sleeve over the splines of the right-hand axle

Section O: General specifications


driveshaft. The sliding sleeve is driven by a fork, which, in turn, is electrohydraulically driven.
Final reduction units ratio: ........................................................... 4.80 : 1 4.80 : 1 4.80 : 1 4.80 : 1 4.80 : 1

Front axle

2 WD axle
Type: ............................................................................................. Three section, adjustable for track (tread) width by means of telescopic tie-rod, by removing securing bolts on each
side of tractor, this allows adjustment in relation to the supporting frame
Options: ........................................................................................ Normal duty Normal duty Normal duty Normal duty Heavy duty
Wheel toe-in: ................................................................................ For all: From 0 to 5.0. positive
Camber / Caster: .......................................................................... For all: 3o 30’ / 0o

Issue 02: 03/03


7
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

8
Issue 02: 03/03
4 WD axle
Type: ............................................................................................. Direct drive, with special protection for the axle against entry of impurities. Side Drive (SD) type on MF 5335 tractor, and
on Central Drive (CD) type (under the engine sump) on all other tractors.
Carraro / Model ............................................................................ Carraro 20.14 SD Carraro / 20.19 CD Carraro / 20.19 CD Carraro / 20.19 CD Carraro / 20.22 CD
Drive: ............................................................................................ For all: Electrohydraulic
Differential lock: ........................................................................... Electrohydraulic, driven by switch on the side console (Platform verion) or instrument panel (Cab version).

Workshop Manual - 5300 Series Tractors


Crown and pinion reduction: ...................................................... 2.153:1 3.444:1 3.444:1 3.444:1 3.444:1
Final reduction units ratio: ........................................................... For all: 6:0 : 1
Wheel toe-in: ................................................................................ For all: 0o
Maximum steering angle: ............................................................ For all: 55o

Section O: General specifications


Brakes
Type: ............................................................................................. For all: Oil-immersed, hydraulic drive.
Number of active discs: ............................................................... For all: 4
Discs material: .............................................................................. For all: Active: Steel with syntherized bronze Fixed: Polished steel.

Hydraulic lift system


Category: ...................................................................................... II (For all tractors and lift system versions)

Ferguson System (Tractors fitted with Platform and Cab)


Operational Controls: .................................................................. Position – Draft – Transport – Response (link drop speed)
Hydraulic pump: .......................................................................... Piston type, ISYP model
Maximum pressure – kgf/cm2: .................................................... 210
Output – Liters/min: ..................................................................... With 540 rpm IPTO = 17.0 With 540/1000 rpm IPTO = 28.0
Hydraulic cylinder(s) - 1 internal +: ............................................ 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)*
Maximum lift capacity (kgf): ........................................................ 2600 / 4000* 2600 / 4000* 2600 / 4000* 2600 / 4000* 2600 / 4000*
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

Boschtronic system operated by levers (platform version only)


Operational controls: ................................................................... Position – Draft – Transport – Drop speed – Rise and lower limitation – safety and mixture locks (draft control’s grade
of actuation).
Hydraulic pump ........................................................................... Additional pump (See 3 - Fig. 500), mounted in tandem with the other two pumps, on the right-hand side of center
housing
Pressure (kfg/cm2) / Output (liters/min): ..................................... Pressure = 210 Output = 28.0 liters/min
Hydraulic cylinder(s) - 1 internal +: ............................................ 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)*
Maximum lift capacity (kgf): ........................................................ 3000 / 4000* 3000 / 4000* 3000 / 4000* 3000 / 4000* 3000 / 4000*

Boschtronic system operated by panel (Cab version only)

Workshop Manual - 5300 Series Tractors


Operational controls: ................................................................... Position – Draft – Transport – Drop speed – Rise and lower limiting – safety and mixture locks (draft control’s grade of
actuation).

Section O: General specifications


Hydraulic pump, pressure and output: ...................................... Idem to the system operated by levers.
Hydraulic cylinder(s) - 1 internal +: ............................................ 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)* 2 exter. (Op.)*
Maximum lift capacity (kgf): ........................................................ 3000 / 4000* 3000 / 4000* 3000 / 4000* 3000 / 4000* 3000 / 4000*

Auxiliary hydraulic systems


Comprised by all the hydraulic systems, excep the lift system: steering, auxiliary hydraulic system, Speedshift (18-speed), IPTO, 4-wheel
drive electrohydraulic, differential lock engagement.
The system includes a specific pump for the auxiliary hydraulic system, another for the hydraulic lift and another one for the all the
remaining systems, including the steering system.

Steering system
Hydraulic pump: .......................................................................... Gear type, transmission driven - See pump on side of center housing. (item 1 - Fig. 500)
Hydrostatic unit: ........................................................................... For all: Danfoss, 4-way-type

Issue 02: 03/03


Steering system pressure and output: ....................................... For all: 145 ~ 150 bar

9
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

10
Issue 02: 03/03
Independent auxiliary hydraulic system
Type: ............................................................................................. With specific gear pump, located on side of center housing. (item 2 - Fig. 500). A derivation of the flow from this pump
is used to activate the trailer hydraulic brake system (Optional).
Valve type: .................................................................................... For all: Double acting; it can also operate with simple acting valve, thanks to a commutating valve.
Terminals type: ............................................................................. For all: Female - quick attach
Number of lines: .......................................................................... For all: Standard = 2 Optional = 3 or 4

Workshop Manual - 5300 Series Tractors


Output – liters/min: ...................................................................... For all: Normal = 38 l/min
Combined flow ............................................................................. As an option for tractors equipped with Ferguson lift linkage, and Standard for tractors fitted with electronic lift linkage.
By means of a control lever on the lateral console, the linkage system’s oil flow can be bypassed to the auxiliary
hydraulic system. The output changes from 38 l/min to 55.0 l/min on tractors fitted with 540-rpm IPTO and Ferguson lift
system, and to 66 l/min on tractors equipped with 540 or 540/1000 rpm IPTO, or fitted with electronically controlled

Section O: General specifications


hydraulic lift.

SpeedShift system - 18-speed transmission (if equipped)


Operation: .................................................................................... In the first compartment of the box, there is a drum which contains 2 clutches: High Range driving clutch, coupled by
plate-type spring action (Belleville) and Low Range driving clutch, coupled by hydraulic pressure. So, with engine shut
off, the gearbox is in “High Range”, thus assuring a connection between the engine and the wheels.
Pressure (bar) .............................................................................. For all: 22 to 24 bar

IPTO hydraulic drive system (if equipped)


Operation: .................................................................................... The IPTO can be driven without using the clutch, thanks to a multidisc clutch located in the tractor’s center housing.
Inside of the drum, plate-type piston presses the discs which, in turn, transmit the movement.
Pressure (bar) .............................................................................. For all: 22 to 24 bar

4 WD front axle electrohydraulic engagement system (if equipped)


Operation: .................................................................................... Under the gearshift box, there is a casing which lodges the coupling system. During thehandbrake or footbrake
actuation, the drive is engaged automatically, thus increasing the braking effect.
Pressure (bar) .............................................................................. For all: 22 to 24 bar
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

Differential locking drive system - front and rear


Operation: .................................................................................... When pressing the switch on the side console, an oil pressure is directed to the lock(s) actuator.
Pressure (bar) .............................................................................. For all: 22 to 24 bar

Trailer hydraulic brake (Optional)


Activation oil flow source ............................................................. Derivation from the auxiliary hydraulic system pump (see 2 - Fig. 500)
Control .......................................................................................... The control of trailer brake is made by the valve (item 4 - Fig. 501).

Independent Power-Take-Off:

Workshop Manual - 5300 Series Tractors


Type 540 rpm: .............................................................................. Standard Standard Standard Standard Standard

Section O: General specifications


Type 540/1000 rpm: ..................................................................... Optional Optional Optional Optional Optional
Engine speed for nominal PTO rotation:
540 rpm IPTO. To obtain 540 rpm, engine at: ................... 1789 rpm
540/1000 rpm IPTO:
- For 540 rpm, engine at: .................................................... 1902 rpm
- For 1000 rpm, engine at ................................................... 2000 rpm
Shaft rotation sense: .................................................................... Clockwise - Seen from the back.
Shaft diameter (mm) / number of splines: .................................. For 540 rpm = 35 / 6 For 1000 rpm = 35 / 21

Tractor weights - in kgf


Without balasting and supplied: 2 WD / 4 WD: ......................... - - 3509 / 3759 3509 / 3759 3871 / 4121
Tractor max. weight with balasting 2 WD / 4 WD ..................... - - 3400 / 3800 4100 / 4500 4700 / 5100

Issue 02: 03/03


11
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

12
Issue 02: 03/03
Tractors general dimensions - in mm
Total Length: 2 WD / 4 WD: ......................................................... - - 4010 / 4050 4010 / 4100 4322 / 4450
Distance between axle: 2 WD / 4 WD: ........................................ - - 2350 / 2350 2350 / 2350 2610 / 2610
Free empty 2 WD / 4 WD: ............................................................ - - 420 420 420
Minimum/Maximum gauges ........................................................ See operator´s book.

Workshop Manual - 5300 Series Tractors


Filling Capacities - in liters
- Fuel tank (Left-hand side): ........................................................ 124.4 124.4 124.4 124.4 124.4
- Optional tank (Right-hand side): .............................................. 74.8 (Opt) 74.8 (Opt) 74.8 (Opt) 74.8 (Opt) 74.8 (Standard)
- Engine: ....................................................................................... 5.0 a 7.0 5.0 a 7.0 6.5 6.5 13.5

Section O: General specifications


- Cooling system: ......................................................................... 14.5 16.0 17.5 17.5 28.0
- Front differential – 4-WD : .......................................................... 5.0 6.0 6.0 6.0 6.0
- Front final reduction units – each 4-WD: .................................. 0.70 1.0 1.0 1.0 1.0
- Rear final reduction units – each : ............................................ 3.0 3.0 3.0 3.0 3.0
- Transmission and hydraulic system: ........................................ 42 to 45 42 to 45 50.0 50.0 50.0
- Brake fluid: ................................................................................. 0.5 0.5 0.5 0.50 5.0

☞ NOTE:
The transmission filling capacity shown above may vary in accordance with tractor’s features. Always take into consideration the
correct levels on the dipsticks!
Furthermore, when attaching implements fitted with auxiliary hydraulic system, add more lubricating oil to the reservoir, as described
in operator´s book.
MF 5335 MF 5340 MF 5355 MF 5360 MF 5365

Wheels nuts torques - kgf.m


Front wheels Rear wheels
1- Reversible pressed disc type: A) Rice version: C) Rim + pressed disc type:
- Disc to axle = 25 - 28 kgf.m - Wheel to axle = 30 - 36 kgf.m - Disc to axle = 30 - 36 kgf.m
- Disc to rim = 13 - 17 kgf.m - Disc to rim = 24 - 29 kgf.m
B) PAVT type:
2- Cast iron type disc (MF 465 and 475) - Cast disc to rim = 29 - 37 kgf.m D) Cast disc type (all):
- Disc to hub = 36 - 48 kgf.m - Clamp nuts = 25 - 29 kgf.m - Disc to axle = 30 - 36 kgf.m
- Disc to rim = 29 - 37 kgf.m - PAVT disc to axle = 34 - 40 kgf.m - Disc to rim = 24 - 29 kgf.m

Workshop Manual - 5300 Series Tractors


Drawbar

Section O: General specifications


Available types: ............................................................................ 1st = Drawbar with rung
............................................................................................. 2nd = HD drawbar with rung
............................................................................................. 3rd = HD drawbar with rung and hitching clevis
Height adjustment: ...................................................................... Drawbar 1: 2 positions Drawbars 2 and 3 : 4 positions
Length adjustment: ...................................................................... 2 or 3 positions, for all kinds of drawbars, by replacing the fastening holes underneath the tractor
Side swing angle: ........................................................................ 22o for both sides, can be oscillating or locked by pins
Automatic drawbar (Autohitch) ................................................... Optional

Cab and air conditioning system (Optional)


Features: ....................................................................................... Supported on rubber pads to absorb vibrations, acoustic and thermal insulation, access to two doors, unsurpassed
all-round visibility, and state-of-the-art ergonomically positioned controls. As an option: AM/FM radio, passenger
seat, and a range of operator’s seats.
Air conditioner: ............................................................................. Belt-driven compressor, SDH15-7952 type.

Issue 02: 03/03


Refrigerant gas: ........................................................................... R-134A - 1.4 kg
Condenser: ................................................................................... Located in front of cooling radiator.
Air filtration: .................................................................................. Paper element located on cab roof.

13

Вам также может понравиться