0 оценок0% нашли этот документ полезным (0 голосов)
11 просмотров2 страницы
This document provides ISO designations for external finishing tool holders with indexable inserts commonly used on light machines. It describes:
1) Two types of tool holders - one for right-hand and one for left-hand cutting.
2) Indexable inserts that fit the tool holders, specifying shape, size, coating, and grade.
3) Spare parts that can be ordered for the tool holders, including shims, pins, levers and screws.
This document provides ISO designations for external finishing tool holders with indexable inserts commonly used on light machines. It describes:
1) Two types of tool holders - one for right-hand and one for left-hand cutting.
2) Indexable inserts that fit the tool holders, specifying shape, size, coating, and grade.
3) Spare parts that can be ordered for the tool holders, including shims, pins, levers and screws.
This document provides ISO designations for external finishing tool holders with indexable inserts commonly used on light machines. It describes:
1) Two types of tool holders - one for right-hand and one for left-hand cutting.
2) Indexable inserts that fit the tool holders, specifying shape, size, coating, and grade.
3) Spare parts that can be ordered for the tool holders, including shims, pins, levers and screws.
EXTERNAL FINISHING TOOL HOLDERS WITH INDEXABLE INSERTS
COMMONLY USED IN MACHINE SHOP-I FOR LIGHT MACHINES
LIKE H-22, H-26, NH-22 etc.
1) Tool Holder PCLNR 2525M12 (i.e., 25 x 25 x 150mm side tool, Right
hand) 2) Tool Holder PCLNL 2525M12 (i.e., 25 x 25 x 150mm side tool, Left hand)
Where P = Type of clamping (inside lever type)
C = Shape of insert (rhomboidal, 80 deg.) L = Style of tool (approach angle 95 deg.) N = Clearance angle of insert ( 0 deg.) R/L = Hand of cutting (right hand for Sl. No. 1 and left hand for Sl. No.2) 2525 = Shank size (square shank 25 x 25mm) M = Tool length (150 mm) 12 = Size of insert (i.e., one side of rhombus =12mm)
This is ISO designation and may be procured on non-proprietary
basis with item description as given in 1 & 2 above. For item 1 similar vocab
09205657057 and for item 2 similar vocab is
no. is
09205664531 3) Insert for above tool holder ( 1 & 2 ): This may be designated as below
“Insert CNMG 120408, uncoated hard metal type, of grade P-40.”
Where, C = Shape of insert (rhombic with nose angle 80 deg.)
N = Clearance angle ( 0 deg. ) M = Tolerance in thickness, corner point, inscribed circle etc. G = Fixing / or chip breaker detail (with hole, with chip breaker on both side) 12 = Insert size (12mm) 04 = Insert thickness (4.76mm) 08 = Corner radius (0.8mm)
This is ISO designation and may be procured on non-proprietary
basis with item description as given in 3 above. For item 3 similar vocab no. is 09205320737.
4) Spares for above tool holders (item 1 & 2):
Spares may be designated as below. As the spares for tool holder 1 & 2 are same only one designation is required.
a) Shim for tool holder PCLNR 2525M12
b) Shim pin for tool holder PCLNR 2525M12 c) Lever for tool holder PCLNR 2525M12 d) Screw for tool holder PCLNR 2525M12 e) Key for tool holder PCLNR 2525M12
For first time procurement the above spares (as mentioned in 4
above) are to be procured by the item description as given in a to e above and afterwards these may be procured on proprietary basis from the supplier of above tool holders with ordering code of these spares.
NOTE: FOR ANY OTHER DESIGN DIFFERING FROM
ABOVE TOOL HOLDERS, ISO DESIGNATION OF TOOL HOLDERS MAY BE REFERRED IN KNOWLEDGE MANAGEMENT PIECE (BSP-2005-0276, TURNING TOOLS WITH INDEXABLE INSERTS) AND FOR INSERTS KNOWLEDGE MANAGEMENT PIECE (BSP-2005-0277, ISO DESIGNATION FOR THROW AWAY INSERTS) MAY BE REFERRED.