Академический Документы
Профессиональный Документы
Культура Документы
Since the olden times, the man has been trying to find our some convenient ways of
lifting water to higher levels, for water supply and irrigation purposes. It is believed, that
the idea of lifting water, by centrifugal force, was first given by L.D. Vinci (an Italian
scientist and engineer) in the end of 16th century. Then this idea was put to experiments
by french scientist and they designed centrifugal pump, having impeller and blades. At
the time the reciprocating pumps were very popular. Then a continuous advancement of
this pump has brought it to a high degree of perfection, which is used all over the world
these days.
Types of pumps
Though there are many types of pumps these days yet the following two are important
from the subject point of view :
1. Centrifugal pump, and
2. Reciprocating pump
In this chapter, we shall discuss the centrifugal pumps only
Centrifugal pump
A pump, in general may be defined as a machine, when driven from some external
source, lifts water or some other liquid from a lower level to a higher level. Or in the
words, a pump may also be defined as a machine, which converts mechanical energy into
presure energy. The pump which raises water or liquid from a lower level to a higher
level by the action of centrifugal force, is a known as a centrifugal pump.
It will be interesting to know that the action of a centrifugal pump is that of a reserved
reaction turbine. In a reaction turbine, the water at hihg pressure, is allowed to enter the
casing which gives out mechanical energy at its shaft : where in pump, the mechanical
energy is fed into the shaft and water enters the impeller (attached to the roating shaft)
which increases the pressure energy of the out going fluid. The water enters the impeller
radially and leaves the vanes axially.
P = wQHmh.p
75η0
2. The power required to drive the pump from the velocity traingles may be
found out by the relation,
P = Discharge in kg x work done/kg of water
75
= wQ.Vw1.v1 h.p
g x 75
Note in S.I units the power required to drive the pump
P = wQ.Vw1.v1 Watts = wQ.Vw1.v1 kW
Example 18.7 A centrifugal pump is requiredd to lift water against a total head of 40 m at
the rate of 50 litres/sec. Find the horse power of the pump, if the overall efficiency is 62
%.
(A.M.I.E., Winter, 1979)
Solution
Given, Total head
Hm = 40 m
Discharge, Q = 50 litres/sec = 0,05 m3/sec
Overall efficiency, η0 = 62 % = 0,62
Let P = Power required for the pump
Using the relation,
P = wQHmh.p
75η0
= 1000 x 0,05 x 40 = 43 .h.p.Ans.
75 x 0,62
Example 18.8 A centrifugal pump delivers 30 litres of water per second to a height of 18
metres through a pipe 90 metres long and of 100 diamete. If the overall efficiency of the
pump is 75 %, find the power required to drive the pump. Take f = 0,012
(Delhi University, 1980)
Solution
Given. Discharge,
Q = 30 litres/sec = 0,03 m3/sec
Height of water H = 18 m
Length of the pipe,
l = 90 m
d = 100 m = 0,1 m
Overall efficiency,
η0 = 75 % = 0,75
Coefficient of friction
f = 0,012
We know that the velocity of water in the pipe,
v= Q = 0,03 = 3,82 m/sec
2
π/4xd π / 4 x l2
Now manometric head,
Hm = H + Loss of head in pipe + Loss of head at outlet
= 18 + 4flv2 + v2
2gd 2g
= 18 + 4 x 0,012 x 90 x 3,822 + 3,822 m
2 x 9,81 x 0,1 2 x 9,81
= 50,87 m
Now using the relation
Reciprocating Pump
A reciprocating pump, in its simplest form, consists of the following parts as shown in
fig. 18-10 :
1. A cylindrical C, in which a piston P works.The movement of the piston is obtained by a
connecting rod, which connects the piston and the rotating crank
2. A suction pipe, connecting the source of water and the cylinder
3. A delivery pipe, into which the water is discharged from the cylinder
4. A valve a, which admits the flow from the suction pipe into the cylinder
5. A valve b, which admits the flow from the cylinder into the delivery pipe.
During the suction stroke, the piston P moves towars right (Le. From 0o to 180o), thus
creating vacuum in the cylinder. Thisvacuum causes the suction valve to open and the
water enters the cylinder. During the delivery stroke, the piston P move towards left (Le.
From 180o to 360o) thus increasing pressurein the cylinder. This increase in pressure
causes the suction valve a to close and delivery valve b to open, and the water is forced
into the delivery pipe.
A reciprocating pump is also called a positive displacement pump, as it discharges a
definite quantity of liquid during the displacement of its piston or plunger. This is why a
reciprocating pump is ideally suitable for grouting in dam foundations.
All the above mentioned pumps will be discussed, in detail at their appropriate places in
the book.
Following table gives the comparisonof a centrifugal pump and a reciprocating pump.
S. No. Centrifugal pump Reciprocating pump
Simple in construction, because of less number Complicated in
of parts construction, because of
more number of parts
Total weight of the pump is less for a given Total weight of the pump is
discharge more for a given discharge
Suitable for large discharge and smaller heads Suitable for less discharge
and higher heads
Requires less floor area and simple foundation Reqires more floor area and
comparatively heavy
foundation
Less wear an tear More wear and tear
Mainteanance cost is less Maintenance costs is more
Can handle dirty water Cannot handle dirty water
Cun run at higher speeds Cannot run at higher speeds
Itsdelivery is continuous Its delivery is pulsating
No air vessels are required Air vessels are required
Thrust on the crankshaft is uniform Thrust on the crankshaft is
not uniform
Operation is quite simple Much care is required in
operation
Needs priming Does not need priming
It has less efficiency It has more efficiency
Q = LAN/ 60
Contoh 18,9.
Sebuah pompa sentrifugal, memiliki efisiensi keseluruhan 62% diperlukan untuk
menangani air garam (sp.gr = 1.19) dan bensin (sp.gr. = 0,7). Jumlah masing-masing
cairan tersebut adalah 50 liter / detik terhadap tekanan bersih 4 kg / cm3. Tunjukkan
bahwa tenaga kuda yang sama dibutuhkan untuk menangani kedua cairan di atas yang
memiliki berat jenis yang berbeda.
Juga menghitung kepala dalam meter cairan yang air garam dan bensin akan
dibangkitkan
(Universitas London)
Pemecahan
Yang ditentukan. efisiensi keseluruhan
η0 = 62% = 0.62
Sp. Gr. dari brino = 1.19
∴ Sp. Berat, wb = 1,19 x 1000 = 1190 kg / m3
Sp. Gr. bensin = 0,7
∴ Sp. Berat wg = 0,7 x 1000 = 700 kg / m3
keluarnya, Q = 50 liter / detik = 0,05 m3 / detik
Tekanan, P = 4 kg / cm3 = 4 x 104 kg / m3
Kepala yang air garam akan dibangkitkan
Kita tahu bahwa kepala air garam,
Hb = P / (w_b) = (4 × 〖10〗 ^ 4) / 1190 = 33,61 m Ans
Kepala yang bensin akan dibangkitkan
Similiarly, kepala bensin
Hg = P / (w_g) = (4 × 〖10〗 ^ 4) / 700 = 57.14 m Ans
Menggunakan relasi,
η_0 = ((wQH) / 75) / P dengan notasi biasa
∴ P_b = (w_b × Q × H_b) / (75 × η_0)
= (1190 × 0,05 × 33,61) / (75 × 0.62) h.p.
= 43 h.p ............ (i)
Similiarly P_g = (w_g × Q × H_g) / (75 × η_0)
= (700 × 0,05 × 57.14) / (75 × 0.62) h.p.
= 43 h.p ............ (ii)
Hal demikian jelas, bahwa datang daya diperlukan untuk menangani kedua cairan yang
memiliki berat jenis yang berbeda. Jawaban.
Contoh 18,10
Tiga tahap pompa sentrifugal memiliki impeler 40 cm dan 2 cm lebar di outlet. Baling-
baling yang melengkung kembali di outlet di 45o dan mengurangi luas keliling sebesar
10%. The effiency maometric dari pompa adalah 90% dan efisiensi keseluruhan adalah
80%. Tentukan kepala yang dihasilkan oleh pompa, ketika menjalankan pada 1000 rpm
memberikan 50 liter / detik. Apa yang harus menjadi kekuatan poros kuda?
(A.M.I.E., Musim Dingin, 1979)
Pemecahan
Yang ditentukan. Jumlah tahap = 3
Diameter impeller di outlet D_ (1) = 40 cm
Lebar impeller pada b_ oulet (1) = 2 cm
Vane sudut di oulet φ = 45o
Daerah dikurangi dengan baling-baling = 10%
Manometric effiency η_man = 90% = 0,9
Secara keseluruhan effiency, η_0 = 80% = 0,8
Kecepatan N = 100 r.p.m
Discharge Q = 50 liter / detik = 0,05 m3 / detik
Kepala dihasilkan oleh pompa
Translate
pengantar
Sejak zaman dahulu, manusia telah berusaha untuk menemukan cara mudah aomw kami
mengangkat air ke tingkat yang lebih tinggi, untuk tujuan suply air dan irigasi. Hal ini
diyakini, bahwa gagasan mengangkat air, berdasarkan gaya sentrifugal, pertama kali
diberikan oleh LD Vinci (seorang ilmuwan dan insinyur Italia) pada akhir abad ke-16.
Kemudian ide ini dimasukkan ke percobaan oleh ilmuwan Perancis dan mereka dirancang
pompa sentrifugal, memiliki impeller dan pisau. Pada saat pompa reciprocating yang
sangat populer. Kemudian kemajuan berkelanjutan dari pompa ini telah membawanya ke
tingkat tinggi kesempurnaan, yang digunakan di seluruh dunia hari ini.
Jenis pompa
Meskipun ada banyak jenis pompa hari ini belum dua berikut penting dari sudut pandang
subjek:
1. pompa sentrifugal, dan
Pompa 2. Reciprocating
Dalam bab ini, kita akan membahas pompa sentrifugal hanya
pompa sentrifugal
Sebuah pompa, secara umum dapat didefinisikan sebagai mesin, jika didorong dari
beberapa sumber eksternal, mengangkat air atau cairan lainnya dari tingkat yang lebih
rendah ke tingkat yang lebih tinggi. Atau dalam kata-kata, pompa juga dapat
didefinisikan sebagai mesin, yang mengubah energi mekanik menjadi energi presure.
Pompa yang raiseswater atau cairan dari tingkat yang lebih rendah ke tingkat yang lebih
tinggi oleh aksi gaya sentrifugal, adalah dikenal sebagai pompa sentrifugal.
Ini akan menarik untuk mengetahui bahwa aksi dari pompa sentrifugal adalah bahwa dari
turbin reaksi dilindungi undang-undang. Dalam turbin reaksi, air pada tekanan hihg,
diperkenankan masuk casing yang memberikan keluar energi mekanik pada poros nya:
mana di pompa, energi mekanik dimasukkan ke poros dan air memasuki impeller
(menempel pada poros roating) yang meningkatkan energi tekanan cairan akan keluar. Air
memasuki theimpeller radial dan daun baling-baling aksial.
P = wQHmh.p
75η0
2. daya yang diperlukan untuk menggerakkan pompa dari traingles kecepatan dapat
ditemukan oleh relasi,
P = Discharge kg x kerja yang dilakukan / kg air
75
= WQ.Vw1.v1 h.p
g x 75
Catatan dalam satuan SI daya yang diperlukan untuk menggerakkan pompa
P = wQ.Vw1.v1 Watts = wQ.Vw1.v1 kW
Contoh 18.7 Sebuah pompa sentrifugal requiredd untuk mengangkat air terhadap kepala
total 40 m sebesar 50 liter / detik. Menemukan daya kuda pompa, jika efisiensi
keseluruhan adalah 62%.
(A.M.I.E., Musim Dingin, 1979)
larutan
Mengingat, Total kepala
Hm = 40 m
Discharge, Q = 50 liter / detik = 0,05 m3 / detik
Efisiensi secara keseluruhan, η0 = 62% = 0,62
Biarkan P = Daya yang dibutuhkan untuk pompa
Menggunakan relasi,
P = wQHmh.p
75η0
= 1000 x 0,05 x 40 = 43 .h.p.Ans.
75 x 0,62
Contoh 18.8 Sebuah pompa sentrifugal memberikan 30 liter air per detik hingga
ketinggian 18 meter melalui pipa panjang 90 meter dan 100 diamete. Jika efisiensi
keseluruhan pompa adalah 75%, cari daya yang diperlukan untuk menggerakkan pompa.
Ambil f = 0,012
(Delhi University, 1980)
larutan
Mengingat. discharge,
Q = 30 liter / detik = 0,03 m3 / detik
Ketinggian air H = 18 m
Panjang pipa,
l = 90 m
d = 100 m = 0,1 m
Secara keseluruhan efisiensi,
η0 = 75% = 0,75
Koefisien gesekan
f = 0,012
Kita tahu bahwa kecepatan air dalam pipa,
v = Q = 0,03 = 3,82 m / sec
π / 4 x d2 π / 4 x l2
Sekarang kepala manometric,
Hm = H + Kehilangan kepala dalam pipa + Kehilangan kepala di outlet
= 18 + 4flv2 + v2
2GD 2g
= 18 + 4 x 0,012 x 90 x 3.822 + 3.822 m
2 x 9,81 x 0,1 x 9,81 2
= 50,87 m
Sekarang menggunakan relasi
reciprocating Pompa
Sebuah pompa reciprocating, dalam bentuknya yang paling sederhana, terdiri dari bagian-
bagian berikut seperti yang ditunjukkan pada gambar. 18-10:
1. Sebuah silinder C, di mana piston P works.The gerakan piston diperoleh oleh batang
penghubung, yang menghubungkan piston dan engkol berputar
2. Sebuah pipa hisap, menghubungkan sumber air dan silinder
3. Sebuah pipa pengiriman, ke mana air dibuang dari silinder
4. katup, yang mengakui aliran dari pipa hisap ke dalam silinder
5. Sebuah katup b, yang mengakui aliran dari silinder ke dalam pipa pengiriman.
Selama stroke hisap, piston P bergerak towars kanan (Le. Dari 0o sampai 180o), sehingga
menciptakan vakum di dalam silinder. Thisvacuum menyebabkan katup hisap untuk
membuka dan air memasuki silinder. Selama stroke pengiriman, bergerak piston P ke
arah kiri (Le. Dari 180o sampai 360o) sehingga meningkatkan pressurein silinder.
Peningkatan tekanan menyebabkan hisap katup untuk menutup dan katup pengiriman b
untuk membuka, dan air dipaksa masuk ke dalam pipa pengiriman.
Sebuah pompa reciprocating juga disebut pompa perpindahan positif, karena akan
dibuang sejumlah tertentu cairan selama perpindahan piston atau plunger. Inilah sebabnya
mengapa pompa reciprocating idealnya cocok untuk grouting di yayasan bendungan.
Semua pompa yang disebutkan di atas akan dibahas, secara rinci pada tempat yang tepat
mereka dalam buku ini.