Академический Документы
Профессиональный Документы
Культура Документы
SERVICE MANUAL
ORIGINAL MANUAL ISSUE DATE: 3/2015
GN1T CHASSIS
Segment: XF
Version Date Subject
1.0 3/2015 Original manual issue.
LCD TV
9-888-573-01
SERVICE MANUAL
GN1T CHASSIS
Segment: XF
LCD TV
9-888-573-01
MODEL LIST
CAUTION
These servicing instructions are for use by qualified service personnel only.
To reduce the risk of electric shock, do not perform any servicing other than that contained in the operating instructions unless you are qualified to do so.
WARNING!!
An isolation transformer should be used during any service to avoid possible shock hazard, because of live chassis.
The chassis of this receiver is directly connected to the ac power line.
CARRYING THE TV
Be sure to follow these guidelines to protect your property and avoid causing serious injury.
• Carry the TV with an adequate number of people; larger size TVs require two or more people.
• Correct hand placement while carrying the TV is very important for safety and to avoid damages.
ATTENTION!!
Ces instructions de service sont à l’usage du personnel de service qualifi é seulement.
Pour prévenir le risque de choc électrique, ne pas faire l’entretien autre que celui contenu dans le Mode d’emploi à moins que vous soyez qualifi é faire ainsi.
WARNING!!
Afi n d’eviter tout risque d’electrocution provenant d’un chássis sous tension, un transformateur d’isolement doit etre utilisé lors de tout dépannage. Le chássis de ce récepteur est
directement raccordé à l’alimentation du secteur.
ALERTE!!
Afi n d’eviter tout risque d’electrocution provenant d’un chassis sous tension, un transformateur d’isolement doit etre utilise lors de tout depannage. Le chassis de ce recepteur est
directement raccorde a l’alimentation du secteur.
1) Do not press on the panel or frame edge to avoid the risk of electric shock.
2) Do not scratch or press on the panel with any sharp objects.
3) Do not leave the module in high temperatures or in areas of high humidity for an extended period of time.
4) Do not expose the LCD panel to direct sunlight.
5) Avoid contact with water. It may cause a short circuit within the module.
6) Disconnect the AC power when replacing the backlight (CCFL) or inverter circuit. (High voltage occurs at the inverter circuit at 650Vrms.)
7) Always clean the LCD panel with a soft cloth material.
8) Use care when handling the wires or connectors of the inverter circuit. Damaging the wires may cause a short.
9) Protect the panel from ESD to avoid damaging the electronic circuit (C-MOS).
10) It is recommended not to exceed 1 hour of Power-On nor Burn-in period with LCD panel face down condition, in repair activity.
After correcting the original service problem, perform the following safety checks before releasing the set to the customer:
1. Check the area of your repair for unsoldered or poorly soldered connections. Check the entire board surface for solder splashes and bridges.
2. Check the interboard wiring to ensure that no wires are “pinched” or touching high-wattage resistors.
3. Check that all control knobs, shields, covers, ground straps, and mounting hardware have been replaced. Be absolutely certain that you have replaced all the insulators.
4. Look for unauthorized replacement parts, particularly transistors, that were installed during a previous repair. Point them out to the customer and recommend their replacement.
5. Look for parts which, though functioning, show obvious signs of deterioration. Point them out to the customer and recommend their replacement.
6. Check the line cords for cracks and abrasion. Recommend the replacement of any such line cord to the customer.
7. Check the antenna terminals, metal trim, “metallized” knobs, screws, and all other exposed metal parts for AC leakage. Check leakage as described below.
8. For safety reasons, repairing the Power board and/or Inverter board is prohibited.
Leakage Test
The AC leakage from any exposed metal part to earth ground and from all exposed metal parts to any exposed
metal part having a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
1. A commercial leakage tester, such as the Simpson 229 or RCA WT-540A. Follow the manufacturers’
instructions to use these instructions.
2. A battery-operated AC milliampmeter. The Data Precision 245 digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a VOM or battery-operated AC voltmeter. The
“limit” indication is 0.75 V, so analog meters must have an accurate low voltage scale.
The Simpson’s 250 and Sanwa SH-63TRD are examples of passive VOMs that are suitable. Nearly all
battery-operated digital multimeters that have a 2 VAC range are suitable (see Figure A).
4x None
<P/T/G/B> Panel ID EEPROM I2C No ACK (Also panel power failure is a suspect) [P_ID_ERR]
5x
<T> TCon IC I2C communication error [TCON_ERR]
Error count
Error item Naming
Total Operation Time [hr] – Boot Count – Panel Operation Time [hr]
Since the diagnostic results displayed on the screen are not automatically cleared, always check the self-diagnostic screen.
After you have completed the repairs, clear the result display to “0”.
1-1. XBR-55X850C/855C/857C
1-1-1. STAND
STAND
1-1. XBR-55X850C/855C/857C
1-1-2. LABEL, UNDER TERMINAL AND LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (L) AND LABEL, CI
(CO1 ONLY)
LABEL, CI
1-1. XBR-55X850C/855C/857C
1-1-3. AC COVER AND POWER SUPPLY CORD
AC COVER
1-1. XBR-55X850C/855C/857C
1-1-4. REAR COVER (L HRN) A
1-1. XBR-55X850C/855C/857C
1-1-5. TAPE AND WIRE DRESSING TAPE
TAPE
1-1. XBR-55X850C/855C/857C
1-1-6. TAPE AND WIRE DRESSING
TAPE
TAPE
1-1. XBR-55X850C/855C/857C
1-1-7. SPEAKER BOX ASSY (L)
2 3
1-1. XBR-55X850C/855C/857C
1-1-8. SPEAKER BOX ASSY (R)
2 3
1-1. XBR-55X850C/855C/857C
1-1-9. TAPE
TAPE
TAPE
TAPE
1-1. XBR-55X850C/855C/857C
1-1-10. BT ANTENNA/WIFI ANTENNA
BT ANTENNA
2 3 4
1-1. XBR-55X850C/855C/857C
1-1-11. SMART CORE
1 SMART CORE 2
1-1. XBR-55X850C/855C/857C
1-1-12. SWITCH UNIT
2 3
SWITCH UNIT
1-1. XBR-55X850C/855C/857C
1-1-13. HARNESS ASSY (MAIN) AND CONNECTOR ASSY 28P
1-1. XBR-55X850C/855C/857C
1-1-14. BRACKET,VESA(HWK)
2 3
BRACKET,VESA(HWK)
1-1. XBR-55X850C/855C/857C
1-1-15. BRACKET, SC(HWK)
2 3
BRACKET,SC(HWK)
1-1. XBR-55X850C/855C/857C
1-1-16. SLIDE, CLAMP
2
SLIDE, CLAMP
1-1. XBR-55X850C/855C/857C
1-1-17. BOTTOM, FRAME (HRN)
2
3
1-1. XBR-55X850C/855C/857C
1-1-18. BRACKET, SP (LAK)
1
2 3 BRACKET, SP (LAK)
1-1. XBR-55X850C/855C/857C
1-1-19. GL3(CH)-STATIC CONVERTER(TV)
2 3
GL3(CH)-STATIC CONVERTER(TV)
1-1. XBR-55X850C/855C/857C
1-1-20. SHEET, INSULATION(HRN L)
(An insulation sheet is under the GL3 power supply board)
1 2
SHEET, INSULATION(HRN L)
1-1. XBR-55X850C/855C/857C
1-1-21. FLEXIBLE FLAT CABLE 41P (XFS) AND FLEXIBLE FLAT CABLE 51P (XFS)
TAPE
FLEXIBLE FLAT CABLE 41P (XFS) FLEXIBLE FLAT CABLE 51P (XFS)
P/N: 1-848-915-11 (Except BR6) P/N: 1-848-914-11 (Except BR6)
2 P/N: 1-848-927-11 (BR6) 3 P/N: 1-848-922-11 (BR6)
1-1. XBR-55X850C/855C/857C
1-1-22. BRACKET, UNDER FL (MOLD)
3
2
1-1. XBR-55X850C/855C/857C
1-1-23. BRACKET, SIDE FL (MOLD)
1-1. XBR-55X850C/855C/857C
1-1-24. BRACKET, TOP FL (MOLD)
1-1. XBR-55X850C/855C/857C
1-1-25. PLATE, MAIN(HWK) ASSY
3
2
1-1. XBR-55X850C/855C/857C
1-1-26. BMFL ASSY
3 BMFL ASSY
2
1-1. XBR-55X850C/855C/857C
1-1-27. GASKET (BMF)
GASKET (BMF) GASKET (BMF)
NOTE:
When you replace a BMFL board, it is necessary to
stick five new GASKET on a new BMFL board.
GASKET (BMF): 4-566-117-01
Guide line
*No indication of direction
Caution:
1. Please aim at the center of square land.
2. Assy the gaskets just before B board panel installation.
1-1. XBR-55X850C/855C/857C
1-1-28. SHEET, THERMAL(BM) AND PLATE, MAIN(HWK)
SHEET, THERMAL(BM)
PLATE, MAIN(HWK)
1-1. XBR-55X850C/855C/857C
1-1-29. SLIDE, CLAMP
2 SLIDE, CLAMP
1-1. XBR-55X850C/855C/857C
1-1-30. LCD PANEL
LCD PANEL
1-2. XBR-65X850C/855C/857C
1-2-1. STAND
STAND
1-2. XBR-65X850C/855C/857C
1-2-2. LABEL, UNDER TERMINAL AND LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (L) AND LABEL, CI
(CO1 ONLY)
LABEL, CI
1-2. XBR-65X850C/855C/857C
1-2-3. AC COVER AND POWER SUPPLY CORD
AC COVER
1-2. XBR-65X850C/855C/857C
1-2-4. UNDER COVER (2L_HWK) A
1-2. XBR-65X850C/855C/857C
1-2-5. TAPE
TAPE
TAPE
TAPE
TAPE
TAPE
1-2. XBR-65X850C/855C/857C
1-2-6. TAPE
TAPE
TAPE
TAPE
1-2. XBR-65X850C/855C/857C
1-2-7. WIRE DRESSING
1-2. XBR-65X850C/855C/857C
1-2-8. SPEAKER BOX ASSY (L)
2 3
1-2. XBR-65X850C/855C/857C
1-2-9. BRACKET, SP (2L HWK) A
2 3
1-2. XBR-65X850C/855C/857C
1-2-10. SPEAKER BOX ASSY (R)
2 3
1-2. XBR-65X850C/855C/857C
1-2-11. BRACKET, SP (2L HWK) A
2 3
1-2. XBR-65X850C/855C/857C
1-2-12. BRACKET,BT (EGL) ASSY
2 3 4 5
1-2. XBR-65X850C/855C/857C
1-2-13. BT ANTENNA/WIFI ANTENNA AND BRACKET, BT(EGL)
1 2
3 4
BT ANTENNA
BRACKET,BT (EGL)
1-2. XBR-65X850C/855C/857C
1-2-14. SMART CORE
1 SMART CORE 2
1-2. XBR-65X850C/855C/857C
1-2-15. SWITCH UNIT
2 3
SWITCH UNIT
1-2. XBR-65X850C/855C/857C
1-2-16. HARNESS ASSY (MAIN) AND CONNECTOR ASSY 28P
1-2. XBR-65X850C/855C/857C
1-2-17. BRACKET,VESA(HWK)
2 3
BRACKET,VESA(HWK)
1-2. XBR-65X850C/855C/857C
1-2-18. BRACKET, SC(HWK)
2 3
BRACKET,SC(HWK)
1-2. XBR-65X850C/855C/857C
1-2-19. SLIDE, CLAMP
2
SLIDE, CLAMP
1-2. XBR-65X850C/855C/857C
1-2-20. BRACKET, STD C (2L_HWK) AND GASKET (HWK STD)
1 2
2 screws (PULLEY, STAND (HWI)) P/N: 4-534-964-01 8 screws (SCREW, +PSW M4X8) P/N: 2-580-600-11
3 4
1-2. XBR-65X850C/855C/857C
1-2-21. GL1A(CH)-STATIC CONVERTER (TV)
1 2 3
1-2. XBR-65X850C/855C/857C
1-2-22. SHEET, INSULATION(HWK 2L)
(An insulation sheet is under the GL1A power supply board)
1 2
1-2. XBR-65X850C/855C/857C
1-2-23. TAPE
TAPE
TAPE
TAPE
1-2. XBR-65X850C/855C/857C
1-2-24. CABLE, FLEXIBLE FLAT 41P AND CABLE, FLEXIBLE FLAT 51P
1-2. XBR-65X850C/855C/857C
1-2-25. BRACKET, UNDER FL (MOLD)
3
2
1-2. XBR-65X850C/855C/857C
1-2-26. BRACKET, SIDE FL (MOLD)
3
2
BRACKET, SIDE FL (MOLD)
1-2. XBR-65X850C/855C/857C
1-2-27. BRACKET, TOP FL (MOLD)
1-2. XBR-65X850C/855C/857C
1-2-28. PLATE, MAIN(HWK) ASSY
1-2. XBR-65X850C/855C/857C
1-2-29. BMFL ASSY
3 BMFL ASSY
2
1-2. XBR-65X850C/855C/857C
1-2-30. GASKET (BMF)
GASKET (BMF) GASKET (BMF)
NOTE:
When you replace a BMFL board, it is necessary to
stick five new GASKET on a new BMFL board.
GASKET (BMF): 4-566-117-01
Guide line
*No indication of direction
Caution:
1. Please aim at the center of square land.
2. Assy the gaskets just before B board panel installation.
1-2. XBR-65X850C/855C/857C
1-2-31. SHEET, THERMAL(BM) AND PLATE, MAIN(HWK)
SHEET, THERMAL(BM)
PLATE, MAIN(HWK)
1-2. XBR-65X850C/855C/857C
1-2-32. CUSHION, CORNER(EGL) AND TAPE
TAPE
TAPE TAPE
1-2. XBR-65X850C/855C/857C
1-2-33. LCD PANEL
LCD PANEL
1-3. XBR-75X850C/855C
1-3-1. STAND
STAND
1-3. XBR-75X850C/855C
1-3-2. LABEL, UNDER TERMINAL AND LABEL, REAR TERMINAL AND LABEL, SIDE TERMINAL (L)
1-3. XBR-75X850C/855C
1-3-3. AC COVER AND POWER SUPPLY CORD
AC COVER
1-3. XBR-75X850C/855C
1-3-4. UNDER COVER (3L_HWK) A
3
UNDER COVER (3L_HWK) A
1-3. XBR-75X850C/855C
1-3-5. TAPE
TAPE
TAPE
TAPE
TAPE
TAPE
1-3. XBR-75X850C/855C
1-3-6. TAPE
TAPE TAPE
TAPE TAPE
1-3. XBR-75X850C/855C
1-3-7. WIRE DRESSING
1-3. XBR-75X850C/855C
1-3-8. SPEAKER BOX ASSY (L)
2 3
1-3. XBR-75X850C/855C
1-3-9. BRACKET, SP (2L HWK) A
2 3
1-3. XBR-75X850C/855C
1-3-10. SPEAKER BOX ASSY (R)
2 3
1-3. XBR-75X850C/855C
1-3-11. BRACKET, SP (2L HWK) A
2 3
1-3. XBR-75X850C/855C
1-3-12. BRACKET,BT (EGL) ASSY
2 3 4 5
1-3. XBR-75X850C/855C
1-3-13. BT ANTENNA/WIFI ANTENNA AND BRACKET, BT(EGL)
1 2
3 4
BT ANTENNA
BRACKET,BT (EGL)
1-3. XBR-75X850C/855C
1-3-14. SMART CORE
1 SMART CORE 2
1-3. XBR-75X850C/855C
1-3-15. SWITCH UNIT
2 3
SWITCH UNIT
1-3. XBR-75X850C/855C
1-3-16. HARNESS ASSY (GBT / MAIN) AND CONNECTOR ASSY, 3P AND CONNECTOR ASSY 9P
CONNECTOR ASSY 9P
HARNESS ASSY (GBT / MAIN)
P/N: 1-910-109-98
P/N: 1-910-109-97
CONNECTOR ASSY, 3P
P/N: 1-848-869-11
1-3. XBR-75X850C/855C
1-3-17. BRACKET,VESA(HWK)
2 3
BRACKET,VESA(HWK)
1-3. XBR-75X850C/855C
1-3-18. BRACKET, SC(HWK)
2 3
BRACKET,SC(HWK)
1-3. XBR-75X850C/855C
1-3-19. SLIDE, CLAMP
1 1
SLIDE, CLAMP
2 2 SLIDE, CLAMP
1-3. XBR-75X850C/855C
1-3-20. BRACKET, STD C (2L_HWK)
1 1
Screw (PULLEY, STAND (HWI)) P/N: 4-534-964-01 Screw (PULLEY, STAND (HWI)) P/N: 4-534-964-01
2 2
4 screws (SCREW, +PSW M4X8) P/N: 2-580-600-11 4 screws (SCREW, +PSW M4X8) P/N: 2-580-600-11
3 3
BRACKET, STD C(2L_HWK) BRACKET, STD C(2L_HWK)
1-3. XBR-75X850C/855C
1-3-21. G4-STATIC CONVERTER(TV)
1 2 3
G4-STATIC CONVERTER(TV)
1-3. XBR-75X850C/855C
1-3-22. SHEET, INSULATION(HWK 3L SYS)
(An insulation sheet is under the G4 power supply board)
SHEET, INSULATION(HWK 3L SYS)
1 2
1-3. XBR-75X850C/855C
1-3-23. GL2-STATIC CONVERTER(TV)
1 2 3
GL2-STATIC CONVERTER(TV)
1-3. XBR-75X850C/855C
1-3-24. SHEET, INSULATION(HWK 3L)
(An insulation sheet is under the GL2 power supply board)
SHEET, INSULATION(HWK 3L)
1 2
1-3. XBR-75X850C/855C
1-3-25. TAPE, FFC (HWK 3L)
1-3. XBR-75X850C/855C
1-3-26. FLEXIBLE FLAT CABLE 41P AND FLEXIBLE FLAT CABLE 51P
TAPE
1-3. XBR-75X850C/855C
1-3-27. BRACKET, UNDER FL (MOLD)
3
2
1-3. XBR-75X850C/855C
1-3-28. BRACKET, SIDE FL (MOLD)
3
2
BRACKET, SIDE FL (MOLD)
1-3. XBR-75X850C/855C
1-3-29. PLATE, MAIN(HWK) ASSY
1-3. XBR-75X850C/855C
1-3-30. BMFL ASSY
3 BMFL ASSY
2
1-3. XBR-75X850C/855C
1-3-31. GASKET (BMF)
GASKET (BMF) GASKET (BMF)
NOTE:
When you replace a BMFL board, it is necessary to
stick five new GASKET on a new BMFL board.
GASKET (BMF): 4-566-117-01
Guide line
*No indication of direction
Caution:
1. Please aim at the center of square land.
2. Assy the gaskets just before B board panel installation.
1-3. XBR-75X850C/855C
1-3-32. SHEET, THERMAL(BM) AND PLATE, MAIN(HWK)
SHEET, THERMAL(BM)
PLATE, MAIN(HWK)
1-3. XBR-75X850C/855C
1-3-33. CUSHION, CORNER(EGL) AND TAPE
TAPE
TAPE TAPE
PLATE, MAIN(HWK)
1-3. XBR-75X850C/855C
1-3-34. LCD PANEL
LCD PANEL
2
WLAN / BT MODULE(11AC) ASSY
1 2
1 Caution!
WLAN / BT MODULE(11AC) Avoid touching on this components
and connector
COVER, TOP
PANEL, ORNAMENT
2 3
LIGHT, GUIDE
1 2
HSC3_S_M MOUNT
Avoid holding or push on these components.
2
WLAN / BT MODULE(11AC) ASSY
1 2
1 Caution!
WLAN / BT MODULE(11AC) Avoid touching on this components
and connector
COVER, TOP
2 3
PANEL, ORNAMENT
2 3
LIGHT, GUIDE
1 2
HSC3_L MOUNT
Avoid holding or push on these components.
Service Mode
Model Information >> 5) After entering service mode, then turn off the power switch.
Self diagnosis History >>
Video / Audio >>
Panel / PQ >> Summary of key behavior
General Setting >>
Tuner >> Key Behavior
Wifi >> Menu Close service menu
SOFTWARE VERSION
1) In Service Mode, select “Model Information”, press “Enter” or “→ ” button to enter Status Information.
Main Micro
Service Mode Model SW Version: PKG2.011.0010NAB
NVM Version: 0001 UC2
Model Information >> Boot Version: V1.000
Self diagnosis History >> Status Information >> PQ Version: 102100006
AQ Version: AQ1.100
Video / Audio >> Model Information >> <Ext>
exFRC: 00.00.00.00
Panel / PQ >> Model Number Setting >> CameraVID: 0
General Setting >> SERIAL NUMBER EDIT CameraPIC: 0
>>
CameraFW: 0
Tuner >> 4k BE
MLFW: SF1.002
Wifi >> MAFW: SF0.360
ADSP SF0.501
NDAT SD0.370
PDAT SD0.370
BDAT SD1.011
BCM SD-------
FDAT SD0.002
UDAT SD0.000
[</>] Set [Home]Exit [</>] Set [Home]Exit BDIX SD0.370
Service Mode
Model Information >>
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi >>
Service Mode
Service Mode
If YES is selected, the input data is saved into EEPROM.
SERIAL NUMBER EDIT is greyed out and the serial number that has been input is displayed. Status Information >>
If NO is selected, the input data is not saved into EEPROM. Service Mode
OK
WB ADJUSTMENT
(Please apply when main board or panel is replaced.) c. To change data , press “←” or “→” on remote commander.
In “Panel/PQ” service mode.
a. Go to “WB Adjustment” category by “↑” or “↓”.
Back <<
Service Mode R WB Gain <[ 0 ]>
Model Information >> G WB Gain <[ 0 ]>
Self diagnosis History >> B WB Gain <[ 0 ]>
Video / Audio >> R WB Offset <[ 0 ]>
Panel / PQ >> G WB Offset <[ 0 ]>
General Setting >> B WB Offset <[ 0 ]>
Tuner >>
Wifi / BT >>
HDD PERFORMANCE CHECK 3. A message "Please wait ..." is displayed during performance check processing.
1. In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then
pressing “Enter” or “→” button to enter inside.
Service Mode
Service Mode
Model Information >> Please wait…
Self diagnosis History >>
Video / Audio >>
Panel / PQ >>
General Setting >>
Tuner >>
Wifi / BT >>
HDD RE-REGISTRATION
1) In “Service Mode”, select “General Setting” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
2) Select “AAA” by pressing “↑” or “↓” then pressing “Enter” or “→” button to enter inside.
No White
Reference Power LED Stationary
Bluetooth /
Smart Core no One Step
& does not colored No video One No video all Wireless Skype
2 3 4 5 6 7 8 9 10 No Remote No Audio LED (Set is still Remote
reponse to lines or of Inputs Inputs can't connect Can't Work
alive) (OSR) can't
remote dots
connect
(Dead Set)
B* Board p l p p p l l p p l l p p l p p p
G* Board l p p p l l p
H* Board p l l
K* Board p l
Speaker p l
LD* Board l p
V By One FFC p p p
Tcon l p p p
LCD Panel p l l p l p
Panel
(Communi Panel Soft-
Power Power LD cation) (Backlight) TEMP ware Emitter
Problem Local
Audio UART
Local
I2C
3-2. NO POWER
3-2-1. NO POWER-PCU
No Power
OK OK
Harness
B* Board
u-Com Failure
DDCON/LDO
START
Check MAIN_VCC
No
Check C9117 Voltage. No Check +3.3V_STBY R9175 Voltage. G-Board
Is the voltage >3.0V? R9144, CN9000 #26pin Is the voltage >1.6V?
Yes
Yes
No Check P_ON_VBUS No
Check R9186 Voltage. Check DC_OFF_DET P-on ucom #pin11 Change IC9017
Is the voltage >3.0V? IC9018 is >3.0V?
Yes
Yes
Yes
Yes Yes
No problem
TV set stays in Check PGOOD_1 No No POWER - DDCON/LDO
STBY MHL charge mode. R9173 Voltage.
Check 1.0V DDCON (IC9008)
Is the voltage >3.0V?
Yes
Yes
Check P_ON_#2 No
P-on ucom #pin14 Change IC9017
Is the voltage >3.0V?
Yes
Check ORESETB No
P-on ucom #pin12 Change IC9017
Is the voltage >3.0V?
Yes
Check X_SYSTEM_RST
No
P-on ucom #pin16 Change IC9017
Is the voltage >3.0V?
Yes
If PANEL_PWER_ON (R9172) is 0V
Check XRST No
Change IC9017
P-on ucom #pin17
Is the voltage >3.0V?
Yes
If BL_MUTE (R9174) is 0V
Check BL_ON No
Change IC9017
P-on ucom #pin18
Is the voltage >3.0V?
Yes
END
Ucom IC9017 is working OK
START
START
Check fuse No
F9xxx Change Fuse
Check Vdd No Is fuse OK?
C9118 Change IC9018
Is voltage >5V?
Yes
Yes Check Vcc voltage No Check POWER_ON P-on ucom #pin19
C9xxx
END Is voltage >12.0V? (Refer to No Power U-Com Failure)
Yes
Yes
Change DDCON IC
START
Yes Yes
Check +5V_MAIN DDCON (IC9001)
Check Enable No
IC9010 #pin1 Change IC9010
Is voltage >2.5V?
Yes
Change DDCON
IC9009
START
Yes
Yes
Yes
Change LDO IC
BMFL/BMFW board
2-time blinking
3-time blinking
B* Board AUDIO
TUNER
HDMI
Go to Tuner check point
Go to HDMI check point
BMF* board
3-time blinking
No
Tuner Error ? See other flows
Yes
[except JP:R6001,R6002,C6004,C6005,R1468,R1469]
Check the voltage of Main Tuner I2C / JL6010, JL6011 NG
[JP,EU:R6003,R6004,C6006,C6007,R1466,R1467]
Check the voltage of Sub Tuner I2C (EU,JP only) / JL6021,
JL6022
[JP only:R6005,R6006]
[If these parts are OK, check Muffin]
OK
OK
NG
Check TU_12V(EU,JP only)/JL 6027 [go to “NO PICTURE@Tuner”]
OK
No No
Audio Error ? See other flow
Replace B-K Harness Yes
B-K harness NG
OK ?
Yes
No
Go to page
Replace K-PWB Yes
Power Off Checking*1 K-PWB NG
OK ?
Go to page No
Power off Checking*2
Note 1: Note 2:
(1) PVDD-GND short check (1) PVDD-GND short check
1) Power Off Checking*1 Measure impedance between PVDD and GND at C7706, Measure impedance between PVDD and GND at C7722, C7762, C7782,
C7707. C7834.
If impedance is <100Ω → NG
If impedance is <100Ω → NG
(2) LDO out short check
(2) LDO out short check
Measure impedance between +3.3V and GND at C9130.
If impedance is <100Ω → NG
Measure impedance between +3.3V and GND at
C7909.
Power Off Check*1 (3) Fuse open check If impedance is <100Ω → NG
Measure impedance of fuse F7700, F7702 5A (12.5V)
If fuse open → NG (3) Fuse open check
Measure impedance of fuse
F7702, F7704, F7705, F7701 5A (12.5V)
Segment “XS”? F7700 3.15A (DDC5V)
Yes If fuse open → NG
No
Power Off Check*3
(1) B-PWB (1) K-PWB
PVDD-GND short ? PVDD-GND short ?
(See Note 1) Yes (See Note 2) Yes
No No
No No
Return to Return to
LED 3x blinking LED 3x blinking
Finish Finish
No Sound
Without LED 3x
No sound only Yes Go to
Analog RF and Digital RF ? No Sound Tuner
Select [External Inputs]→
AV receiver is connected Yes
[BRAVIA Sync Settings]→
to HDMI in ?
[BRAVIA Sync Control]→[off] No
No
Yes Go to
No sound only HDMI ?
No Sound HDMI
[Speakers] setting is Yes Change the setting to
[Audio System] ? [TV Speakers] No
No Go to
No Sound Audio
Headphone is connected to Yes
Disconnect the Headphone
HP/Audio Out terminal ?
No
[Sound]→ Change [Sound]→
Yes
[Headphone Speaker Link] [Headphone Speaker Link]
setting is [On] ? Yes to [Off], OK ?
No No
Replace B-PWB
Go to
Power Off Checking*1 HP/Audio out terminal or Headphone detect
GPIO may be broken
BMFL/BMFW board
OK
IC1000
4-time blinking
0.897V or less
B* Board
5-times blinking
NG
Change Change
B-Board Panel (T-con)
Check NG OK
“+12.5V_TCON” at G-Board is
Replace G-Board
CN9000 suspicious
Symptom Symptom
on the B-Board
improvement improvement
NG
OK B-Board is Panel (T-Con) is
suspicious suspicious
Symptom
Replace the Harness improve Harness is
Between G-Board
suspicious
and B-Board
NG
Symptom
improve
Replace V-By-One FFC
the V-By-One FFC is suspicious
NG
6-times blinking
Check a voltage of
Harness /
BL_ERR_DET. Check
Connection
Check point is Voltage ≥ 1.9 V harness/connection
Change Symptom
broken
JL9007 G*board to B*Board Harness
harness Improvement
or or
23pin of CN9000 LD board to B*Board
No improvement
on B*Board
No improvement
Change Symptom
Panel
Panel Improvement
No Improvement
Change Symptom
B* Board
B* board Improvement
7-time blinking
Setting
circumstance is OK? No Set to another
Temperature, location, etc.
Ventilation, etc.
Yes
Change B* Board, NG
and Aging a few Panel
hours
Symptom
improvement
Check I2C_C bus Yes Temp sensor
B* Board NG communication OK?
IC1400
(check the next page)
No
3-4. NO SOUND
3-4-1. No Sound Audio 3-4-2. No Sound : TUNER
Yes NO
Segment “XS”? Only RF tuner input?
YES
No
No
No
Finish
No Sound
NG
Check the picture Refer to MHL NO PICTURE
OK
OK
Check Sound by other TV set
Refer to No Sound Audio
which is same model
NG
NG
No Sound
NG
Check the picture Refer to HDMI (1/2/3/4) NO PICTURE
OK
Does this model have YES
Check the mode DVI Connect Stereo minijack cable between Source and the TV, and
Analog Audio In
of Source equipment Change “HDMI/DVI Audio Source” to Auto or Analog Audio In.
(Stereo minijack)?
No
HDMI Change the mode of Source equipment to HDMI
Analog Audio In
Does this model have YES “HDMI/DVI Audio Source”
Analog Audio In Change “HDMI/DVI Audio Source” to Auto or HDMI Audio In
setting is?
(Stereo minijack)?
Auto or HDMI Audio
NO
NG
3-5. NO PICUTURE
BL_ON:H
No Check Smart Core No Check Replace NG NG
Got Any Normal Replace LCD Panel
Behavior BL_ON the V by One FFC
Display? the main Board (T-CON)
(5x Blinking) on the main board Harness
HDMI - No Picture
Tuner - No Picture
No Picture AEP
NG
** Detailed check all parts
at SCART_FB signal
** Detailed check all parts at Path [VD7504/R7513]
CN7501 along signal path
at Pin No: OK
Check wave between NG (Vpp: 0 V)
7 : [VD7503/R7503/C7501/ Detailed check all parts at
C7502/C7505/C7507 R7504] NG (Vpp: 0 V) CN7501 along signal path NG
and IC1000 11 : [VD7502/R7506/C7503/ NG Check wave between
at Pin No:
R7507] C7511 and IC1000
20 : [D7505/R7518/C7510/
15 : [VD7501/R7510/C7506/ R7599/R7519]
OK (Vpp: 1 V) R7511]
OK (Vpp: 1 V)
OK OK
Muffin [IC1000] CN7501 Connectivity CN7501 Connector Muffin [IC1000] CN7501 Connector CN7501 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem
No Picture AEP
Video 2 Component
No Picture No Picture
OK
Muffin [IC1000] J7504 Connector J7504 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem
No Picture Video
Video 1 Video 2
No Picture No Picture
NG
NG * Check J7505 * Check J7504
Check if input OSD NG (Vpp: 0 V) Check if input OSD NG (Vpp: 0 V)
Connection, Connection,
is GREY OUT is GREY OUT
VIDEO2_DET VIDEO_DET
OK if it is highlighted OK if it is highlighted
At R7562 At R7539
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)
OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK
Muffin [IC1000] J7505 Connector J7505 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem
No Picture Video
Component
No Picture
NG
Check if input OSD * Check J7504 Con NG (Vpp: 0 V)
is GREY OUT VIDEO_DET at R7539,
OK if it is highlighted CR_DET at R7538
OK
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)
OK
No Picture
Video1 Video2
No Picture No Picture
OK (Vpp: 1 V) OK
OK (Vpp: 1 V) OK
Muffin [IC1000] J7501 Connector J7501 Connectivity Muffin [IC1000] J7504 Connector J7504 Connectivity
Parts Broken Parts Broken
Problem Problem Problem Problem Problem Problem
No Picture
Component
No Picture
OK
OK (Vpp: 3.3 V)
OK (Vpp: 3.3 V)
OK
Notes:
I2C line for all tuners except Japan_SKP
- Parts for I2C_A_SDA line: R6001, C6004.
RF input no picture / noisy picture - Parts for I2C_A_SCL line: R6002, C6005.
Digital
Satellite
OK OK OK
Check Tuner power line Check P_ON_LNB signal line MOSFET Q9019
Check fuse F6000
12V at JL9012 = 12V? at R9167 = 3.3V? broken
NG NG NG
NG
Check harness between
Harness broken
B-Board and G-board
OK
Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327,
C6301, R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326,
C6300, R6300.
For LA-ISDB(BR/AR), LA-T2(COL) and TW only - Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
Analog Tuning
R6303.
For Other destination
NG A : Insert correct signal in correct terminal.
Confirm ANT or Cable connection A
OK
OK
Check IC1000(SOC)
Notes:
- Parts for IFOUT_N line: R6007, FB6002, C6008, R6327, C6301,
R6301.
- Parts for IFOUT_P line: R6008, FB6003, C6009, R6326, C6300,
Digital Tuning 1 R6300.
- Parts for IFAGC line: R6072, R6009, R6010, R6069, C6302,
For TW only R6303.
For all
tuners A : Insert correct signal in correct terminal.
NG
except TW
Confirm ANT or Cable connection A
OK
Sound is normal?
OK
Check part mounting condition for digital data line
“IFOUT_N, IFOUT_P, IFAGC”
NG
3-5-11. FOR DIGITAL TUNING 2: @ AEP_W, JP_SKP, PA_T2, CH/HK, LA-ISDB(BR/AR) and LA-T2(COL)
OK OK OK
Terrestrial All except SKP_Opticast BS/CS or SKP_Opticast/
Digital cable/ Terrestrial
SKP_Premium or terrestrial
Cable OK SKP_Opticast
Sound is normal?
On Service Notes:
mode display CASE B - Parts for TU1_TS_DATA0 line: R6015,
TS_LOCK ? R6321.
UEC ? - Parts for TU1_TS_CLK line: R6016, R6322.
- Parts for TU1_TS_VALID line: R6017, R6323.
CASE A - Parts for TU1_TS_SYNC line: R6018, R6324.
Change Tuner module
(Refer to Note tuner ) - CASE A : TS _LOCK = LOCK and UEC
constant
- CASE B : TS _LOCK = UNLOCK or UEC is
OK increasing
Check part mounting condition for digital data line
“TU1_TS_DATA0, TU1_TS_CLK, TU1_TS_VALID, TU1_TS_SYNC”
Note Tuner –
(IC reference -- destination)
TU6001 - PA-T2
NG TU6001 - LA-T2/LA-ISDB
TU6001 - CH, HK
Check IC1000 (SoC)
TU6003 - AEP_W
TU6802 - JP_SKP
Change NG parts
A : Insert correct signal in correct terminal.
No Picture
Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244
No Picture
Reference TV set
NG
Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244
No Picture
Reference TV
set
NG Replace
IC1000
Check the settings of JC5227, JC5228, JC5235, JC5236
Source equipment JC5241, JC5242, JC5243, JC5244
No Picture
If you can do
Check the below point at
component repair All lines
Connector side
Other Input is OK are NG
Check other ・Check +5V line Replace
Change B-Board.
HDMI input ・Check HPD line CN5208 NG
・Check DDC lines
All Inputs are NG ・Check TMDS lines
No Picture
Check voltage at
CD_SENSE_0,
High NG (No communications)
R5509 Check HDMI_0_HPD_CBUS
Replace IC5212(HDMI EQ).
Spec:High:2.0~5.3V at connector side
Low:0.8~2.0V
OK
Low NG (No communications)
Check TMDS(D0+/D0-) lines
at connector side
Replace
RB5211
OK
Low (< 2V)
Check DDCCLK,
Check RB5219 (47k ) Check Source equipment
at CL5256
NG (Open) by Reference TV set
High OK (For example, Samsung TV(UN46ES7000),
Replace Toshiba TV(42WL863), RB1, RB2) OK
RB5219
NG
No Charge
TV On
5V
CN5202 #18 pin Change MHL Cable
0V
High 0V
Check voltage at 0V
Check IC5208 #6 Check IC5208 #3
CD_SENSE_0, Replace IC1000 (SoC).
(VBUS IC, Out) (VBUS IC, EN)
R5509
Low (< 2V) 5V
High Replace
OK
RB5219
Change
MHL cable Check D5205, D5206 NG (Open)
Replace
OK
D5205, D5206
NG
Change OK
Switch unit-B* board Harness Harness issue
NG
NG
Power Key (B*Board) NG Key AD(B*Board)
NG Check parts value :
Check parts value : Parts Broken issue
0 ohm < R1089 < 2 ohm 0 ohm < R1091 < 2 ohm
4.4k ohm < R1432 < 5k ohm 0 ohm < R1042 < 2 ohm
OK OK
NG NG
Change B*Board
NG
Harness on H-board OK Harness
and B* Board connection
properly connected issue
NG
NG
OK
Change Smart Core Smart core issue
NG
B*Board
NG
Check parts value : Parts Broken issue
R1080 = zero ohm
OK
NG
Change B*Board
NG
OK H-B* board harness
Change
H-B* board Harness issue
NG
OK
Change Smart Core Smart Core issue
NG
B*Board NG
Check LIGTH_SENSOR signal path : Part broken issue
R1079 = zero ohm
OK
LIGTH_SENSOR (Muffin Pin L35) OK
Check voltage variation from Muffin IC1000 problem
room light to dark condition
NG
Change B*Board
[Network Set-up]
>[Wired Set-up]
on the TV
OK OK OK
Connection Results Connection Results Connection Results
Cable Connection Local Access Internet Access
B board
OK Auto
Check Proxy setting
Check cable B board Wired Set-up
Local router
IP address setting
DHCP server
NG Manual
Wireless Network
on the TV
Yes Yes
NG
Change WiFi module Access Point
From previous page
OK
WiFi module
Check harness
NG OK
connection is OK Connect properly Loose harness
between WiFi and Bxx
OK NG
Change harness
Change NG NG
between Bxx board Change Bxx board
Wi-Fi module
and WiFi
OK If Wi-Fi malfunction happens,
OK
• Wi-Fi module
• Harness between WiFi
Wi-Fi module Main Harness and Bxx
• Bxx board
are suspected.
3) Bluetooth malfunction
Please refer
OK Touch pad Remote manual
Home > Settings > Check BT antenna OK 3D-glasses (Active) manual
Bluetooth Settings Can read Connection is OK
Or
Near discoverable
Bluetooth Device Bluetooth Speaker/Headphone/Headset operation manual
NG NG
else
OK Loose BT antenna
Connect properly connection
NG
Check harness NG OK
connection is OK Connect properly Loose harness
between BT and Bxx
OK
NG
NG Change harness NG
Change BT module Between Bxx board Change Bxx board
and BT
OK OK
4-1-2. LA(BR/AR)
4-1-3. LA(COL)
GL3 Board
CN6401
1-842-551-11
SJM20-28WLB/JAM
DIGITAL_STBY 1 NC
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 24
BL_ERR 8 23 CN7700
POWER_ON 9 22 #24 1 1 SP_MAIN_RP
GND 10 21 #22 #24 2 2 SP_MAIN_RN
GND 11 20 #22 #24 2 3 SP_MAIN_LN
GND 12 19 #22 #24 1 4 SP_MAIN_LP
REG12V 13 18 #22 1-842-593-11 1-842-566-12
REG12V 14 17 #22 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11
CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
1-839-678-21
CN6801
1-822-359-11
53426-0410
+OUT1 1
NC 2 To LS
+OUT2 3
NC 4
1-822-326-11
51103-0400
CN6802
1-843-363-11
53426-0810 Molex
-OUT1-1 1
-OUT1-2 2 To LS
-OUT1-3 3
-OUT1-4 4
-OUT2-1 5
-OUT2-2 6
-OUT2-3 7
-OUT2-4 8
1-822-330-11
51103-0800
DIAGRAMS
183
(Only Interface between board and board)
SM BAX_F Board
BMFL Board CN3601 To BMFW (BMFL) J106 T-con Board
CN203 GND 1 51 GND
1-798-511-11 HUS_GND 1 19 VBTX7P 2 50 RxP7 (AUO) PANEL FFC
HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7 80pin x4
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 J101_F2
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6 J102_F2
GND 7 45 GND J103_F2
VBTX5P 8 44 RxP5 J104_F2
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
#30 5 5 WIFI_GND VBTX2P 17 35 RxP2
#30 6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
#30 9 9 WIFI_GND VBTX1N 21 31 RxN1
#30 10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
#30 11 12 BT_3D_LR VBTX0N 24 28 RxN0
#30 13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 Reserved
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 Reserved
1 19 HUS_GND BITSEL 31 21 NC(BITSEL(High/Open:10Bit; L:8Bit))
CN101 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 nWP(High:Write; L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 3D_EN
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 3D_Sync_In
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 3D_Sync_out
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 NC
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 NC
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 NC
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 NC
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 NC
NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 NC
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 NC
NC 39 CAM_GND NC(ABL_HOT0)/12V 51 1 NC
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE 51pin
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
GL1A Board
CN7700
1 1 SP_MAIN_RP
2 2 SP_MAIN_RN
CN6401 2 3 SP_MAIN_LN
1-842-551-11 1 4 SP_MAIN_LP
SJM20-28WLB/JAM 1-842-593-11 1-842-566-12
DIGITAL_STBY 1 NC PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 24
BL_ERR 8 23
POWER_ON 9 22
GND 10 21 #22
GND 11 20 #22
GND 12 19 #22
REG12V 13 18 #22
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11
CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2
AC pigtail
1-839-678-21
CN6801
1-822-359-11
53426-0410
+OUT1 1
+OUT2 2 To LS
+OUT3 3
+OUT4 4
1-822-326-11
51103-0400
CN6802
1-843-360-11
53426-0510 Molex
-OUT1 1
-OUT2 2 To LS
-OUT3 3
-OUT4 4
NC 5
DIAGRAMS
184
(Only Interface between board and board)
SM BAX_F Board
BMFL Board CN3601 To BMFW (BMFL) T-con Board
CN203 GND 1 51 GND
1-798-511-11 HUS_GND 1 19 VBTX7P 2 50 RxP7 (SDC) PANEL FFC
HUS_KEY_AD 2 18 VBTX7N 3 49 RxN7 XX pin xX
HUS_POWER_KEY 3 20 GND 4 48 GND
1-821-143-11 1-821-117-11 VBTX6P 5 47 RxP6 unknown
JAM SYT10-3WL SYT10-03HG VBTX6N 6 46 RxN6 unknown
GND 7 45 GND unknown
VBTX5P 8 44 RxP5 unknown
VBTX5N 9 43 RxN5
GND 10 42 GND
VBTX4P 11 41 RxP4 15171601
CN1000 VBTX4N 12 40 RxN4
1 1 WIFI_GND GND 13 VbyOne-FFC 39 GND
2 2 X_WIFI_BT_RST VBTX3P 14 38 RxP3
3 3 X_WIFI_WAKEUP VBTX3N 15 37 RxN3
4 4 X_BT_WAKEUP GND 16 36 GND
#30 5 5 WIFI_GND VBTX2P 17 35 RxP2
#30 6 6 WIFI_STBY_3.3V VBTX2N 18 34 RxN2
USB 7 7 WIFI_STBY_3.3V GND 19 33 GND
Main Harness USB 8 8 WIFI_STBY_3.3V VBTX1P 20 32 RxP1
#30 9 9 WIFI_GND VBTX1N 21 31 RxN1
#30 10 10 WIFI_GND GND 22 51pin FFC 30 GND
USB 12 11 WIFI_GND VBTX0P 23 29 RxP0
#30 11 12 BT_3D_LR VBTX0N 24 28 RxN0
#30 13 13 WIFI_GND GND 25 27 GND
USB 14 14 WIFI_USB_M VBTXLOCKN0 26 26 LOCKN
NC 15 NC VBTXHTPDN0 27 25 HTPDN
USB 15 16 WIFI_USB_P GND 28 24 GND
NC 17 NC GND 29 23 SDC Use
GN1 Smart Core 2 18 HUS_KEY_AD NC 30 22 SDC Use
1 19 HUS_GND BITSEL 31 21 SDC Use
CN101 3 20 HUS_POWER_KEY /WP/(BINT) 32 20 B_INT (High:Write / L/Open: Protect)
STBY3.3V 1 25 11 21 SC_OPT_SENSE SCL 33 19 SCL
HSC3-L 5V_MAIN 2 22 2 22 5V_MAIN SDA 34 18 SDA
GND 3 27 12 23 SC_SIRCS 3D_EN/(MUTE) 35 17 3D_EN
LED_AMBER 4 24 4 24 SC_LED_AMBER 3D_SYNC_IN 36 16 3D_Sync_In
LED_PWM_W 5 26 1 25 SC_STBY_3.3V 3D_SYNC_OUT 37 15 SDC Use
LEY_PWM_R 6 32 5 26 SC_LED_PWM_W GND 38 14 GND
LED_PWM_B 7 30 3 27 SC_GND PANEL_DET 39 13 GND
LED_PWM_G 8 28 8 28 SC_LED_PWM_G GND 40 12 GND
GND 9 29 9 29 SC_GND NC/GND 41 11 GND
MAIN_3.3V 10 31 7 30 SC_LED_PWM_B NC 42 10 GND
OPT_SENSE 11 21 10 31 SC_MAIN_3.3V NC 43 9 NC
SIRCS 12 23 6 32 SC_LED_PWM_R NC(PANEL_RESETX)/12V 44 8 NC
1-821-139-11 1-821-126-11 NC 33 SC_GND NC(PANEL_READY)/12V 45 7 NC
JAM SYT10-12WS SYT10-12HG NC 34 NC NC/12V 46 6 NC
XBR-75X850C/855C
NC 35 MIC_GND NC(PANEL_PWR)/12V 47 5 NC
NC 36 MIC_RESET NC(PANEL_ON)/12V 48 4 NC
182113911 NC 37 I2S_BCK(SIELDED) NC(ABL_HOT2)/12V 49 3 NC
NC 38 I2S_LRCLK(SIELDED) NC(ABL_HOT1)/12V 50 2 NC
NC 39 CAM_GND NC(ABL_HOT0)/12V 51 1 NC
USB Cable(UL2725) NC 40 CAM_POP 1-842-546-21 1-819-812-11
Wifi/BT GND 1 1 1-819-538-11 1-818-692-23 FFC Direct Connector :IPEX JAE/FI-RE51S-HF
RST_L 2 2 SHLDP-40V-S-1 (B) JST SM40B-SHLDS-GANF-1-TF(LF)(SN) or Yamaichi 1-843-107-XX
WOW_L 3 3
WOBT_L 4 4 CN3600 To BMFW (BMFL) XXX
G4 Board
CN7700
1 1 SP_MAIN_RP
2 2 SP_MAIN_RN
CN6401 2 3 SP_MAIN_LN
1-842-551-11 1 4 SP_MAIN_LP
SJM20-28WLB/JAM 1-842-593-11 1-842-566-12
DIGITAL_STBY 1 30 PBVP04V-S SM04B-PBVSS-TB(LF)(SN)(PS)
DC_DIMMER 2 29
BL_ON 3 28
PWM_DIMMER 4 27
STBY_3.3V 5 26 #22 G-B Harness
GBK
BLINKING 6 25
AC_OFF_DET 7 24
BL_ERR 8 23
POWER_ON 9 22
GND 10 21 #22
GND 11 20 #22
GND 12 19 #22
REG12V 13 18 #22
REG12V 14 17 #22
REG12V 15 16 #22
REG12V 16 15 #22
REG12V 17 NC
REG12V 18 13 #22
GND 19 NC
GND 20 11 #22
TCON_GND 21 1 #22
GND 22 9 #22
TCON_GND 23 2 #22
TCON_ON 24 7
TCON_VCC12V 25 4 #22
TCON_VCC12V 26 5
TCON_VCC12V 27 5 #22
TCON_VCC12V 28 NC
SJM20-28HG
1-842-598-11
CN6402
1-822-364-11 MOLEX
53426-0910
DC_DIMMER(G) 1 1
PWM_DIMMER(G) 2 2
BLINKING(G) 3 3
BL_ERR(G) 4 4
NC 5 NC
DIGTAL_STBY(G)/P_ON(G)6 6
BL_ON(G) 7 7
GND(G) 8 8
12V(G) 9 9
1-822-331-11
51103-0900
CN6103
1-691-961-11 JST
B2P3S-VH-B(LF)(SN)
AC-N 1 1
AC-L 3 3
1-562-211-11
VHR-3N
GL2 Board
CN6102
1-691-961-11 JST GG Harness
B2P3S-VH-B(LF)(SN)
AC-N 1 1
AC-L 3 3
1-562-211-11
VHR-3N
CN6803
1-822-364-11 MOLEX
53426-0910
DC_DIMMER(G) 1 1
PWM_DIMMER(G) 2 2
BLINKING(G) 3 3
BL_ERR(G) 4 4
NC 5 NC
DIGTAL_STBY(G)/P_ON(G)6 6
BL_ON(G) 7 7
GND(G) 8 8
12V(G) 9 9
1-822-331-11
51103-0900
CN6801
1-822-359-11
53426-0410
+OUT1 1
+OUT2 2 To LS
+OUT3 3
+OUT4 4
1-822-326-11
51103-0400
CN6802
1-843-360-11
53426-0510 Molex
-OUT1 1
-OUT2 2 To LS
-OUT3 3
-OUT4 4
NC 5
1-822-327-11
51103-0500
CN6101
SFP79-02WLB JAM
1-822-908-11
AC-N 1
AC-L 2 AC pigtail
DIAGRAMS
185
DIAGRAMS
KJ002 KJ001
L7700
F7702 CN7703
C7742 cam15
C7707 C7720
C7719
C7743
C7741 DM001
cam005
C7727 L7701
cam059
R7763 R1489
C7713
C7
712C7864 cam24 cam18 cam19 cam21 cam205 cam22 R1485
C7875 D1001
R7764 C1455
C7728 R1078
R7753 D1002
C7779 C7780 R1108
R7754 IC7701 R1083 R1086
087 CL1006 R1126 R1129 D1402 R1487 IC1404
VD1002 3 R1 C107 cam004
R1084 RB1400
C7705 R7759 C7729 C7781 C7782 R1081 C1055 C1083 R1106 R1486
C7750 R1073 C1076 C1074 R1105 cam201
C7876 C7744 C1056 VD1400
R7729 C7718 C7752 C1077 8R1089 C1066 R1127
R7968 L7702 C7753 R108 R1478
cam095 C1082 R1062 R1109 7R1077
6 R10 R1128 R1479
R7755 R1107 C1057 14711470RR1480R
C775
cam032 C1079 R1085 R1082 R1090 VD1000 C1065
R7756 1 VD1001 CL1004
005CL1 C1070 C1449 cam206
C1061 D1003 C1067 R1075 C1450
C7730 C IC1401
R7757 R7767 R1 R1091 C1068 C1064 C1072
C7709 1062C1078 C1075 080R1079 71
CL1003 RB1000
C7745 TP3111 C10
cam37 D1400
cam011 CL1008
007CL1 cam32
IRM002 cam017
TP3102
CN7700 CN7705 CN7704 cam001
L7703 CN1000 C1441
IC1400
KA004
KA002 cam010
cam7 cam9
BMFL (B SIDE)
KJ004 KJ003
KB003
ET011
JL8017
JL1009
ET027
IRM003
JL9001 JL9000
ET024
JL9003 JL9002
JL9023 JL9004
JL9005
JL8008 ET016
JL9007 JL9006
JL8006
JL9024 JL9008
JL8005
JL8007
JL9012
JL9011
ET007
JL9014
ET009
ET028
JL9009
JL9013
10 CL
98CL9800
ET025
JL9010
ET012
ET015
CL1001
CM7704 CL1000
CL8301
JL9800
CL9803
CL9801
CL7601 CL8308
CL9805 CL7708
CL7764
CL8307
CL7763
JL8011 CL3604
CL3109
JL8010
ET006
JL8009 ET014
JL9018
CL8706
JL8000 CL8708
CL8005
600CL7
ET013 7CL8711
10 CL8 CL8709 CL8707
CL6000
CM7701
JL9017
ET030
JL3102
ET017
JL3101
CL8004 JL3103 ET026
JL9025
JL3100
JL9026
ET018 ET029
cam083
JL5208 JL3104
camET004
JL3600
JL6032
JL6018 JL6031
ET022 JL6033
CL5280
ET019
JL5209 CL5281
JL6027
JL6026 JL6024 JL6023 JL6021 JL6017 JL6015 JL6802 JL6013 JL6012
JL7814
JL6025 JL6022 JL6020 JL6016 JL6014
JL1412 JL7789
JL7790
JL7795
JL1411 JL7816
JL7791
JL7815 JL7794
CL5267 JL7788
JL5207 CL5266
CL5290
CL5289
CL5288 JL6034 JL7798
JL5203 CL5287 JL7832
JL5202 CL5286
CL5285 JL7799
CL5284 JL9015 JL7800
JL5204 CL5268 JL7801
JL5205 CL5282 ET021
JL9016 JL7802 JL7803
JL5206 CL5283
JL9022
JL6019
JL6028 JL6011 JL6010 JL7804
JL5201
JL7813
JL6030 JL6004 JL6006
JL9021
JL8012
ET6001 JL6009 JL8013
ET6000
JL8015
JL8002 JL6005
JL9020
JL6029
JL9019
JL1403 JL1400
JL1401
JL7500 JL1406 JL1407
cam011 JL1402
JL1410
cam012 JL1404
JL1405
JL1408 DM002
JL7829
JL7830 JL7831
JL7506 JL1409
cam16
cam209 cam208
cam096 cam23
cam210
JL7507
cam006
cam17
JL7824 JL7823
JL7820 JL7819
IRM004
XBR-55X850C/855C/857C XBR-65X850C/855C/857C
BMFL
BMFL
XBR-75X850C/855C
SWITCH UNIT
5-1. XBR-55X850C/855C/857C
REF. No. PART No. DESCRIPTION MARK
5-1-1. REAR COVER
1 4-567-609-01 LABEL, CI CO1
2 4-563-756-01 LABEL, SIDE TERMINAL (L)
3 4-563-760-01 LABEL, UNDER TERMINAL UC2
3 4-563-760-11 LABEL, UNDER TERMINAL LA1
3 4-563-760-21 LABEL, UNDER TERMINAL CR1/ECU/LA8/
CO1/BR6
4 4-563-764-01 LABEL, REAR TERMINAL UC2
4 4-563-765-01 LABEL, REAR TERMINAL except UC2
5 1-839-695-12 POWER-SUPPLY CORD (WITH CONN.) CR1/ECU/LA8/BR6
5 1-839-696-12 POWER-SUPPLY CORD (WITH CONN.) CO1/UC2/LA1
6 4-297-989-01 AC COVER BR6
6 4-299-531-01 AC COVER except BR
7 1-754-952-11 BT ANTENNA except BR
7 1-754-954-11 BT ANTENNA BR6
8 1-859-100-11 SPEAKER BOX ASSY (L)
9 1-859-100-21 SPEAKER BOX ASSY (R)
10 1-798-510-31 SWITCH UNIT (SM-G-WW) except BR
10 11 10 1-798-510-41 SWITCH UNIT (SM-G-KIT) BR6
11 4-559-710-01 REAR COVER (L HRN) A CO1
11 4-559-710-11 REAR COVER (L HRN) A CR1/ECU/LA8/
UC2/LA1
8
11 A-2073-677-A REAR COVER (L HRN) A BR6
SMART CORE 1
(M, L)
2
7
4
57
53
59 54
56
59
58
55
5-1-3. CONNECTORS
101 102
103
104
5-1-4. SCREWS
207 203
204
206
205
257
252
259
257
257 253
259
257
256 254
258
255
5-2-3. CONNECTORS
5-2-4. SCREWS
5-3. XBR-75X850C/855C
5-3-1. REAR COVER REF. No. PART No. DESCRIPTION MARK
401 4-563-756-01 LABEL, SIDE TERMINAL (L)
402 4-563-760-01 LABEL, UNDER TERMINAL UC2
402 4-563-760-11 LABEL, UNDER TERMINAL LA1
402 4-563-760-21 LABEL, UNDER TERMINAL BR6
403 4-563-764-01 LABEL, REAR TERMINAL UC2
403 4-563-765-01 LABEL, REAR TERMINAL BR6/LA1
404 1-839-695-12 POWER-SUPPLY CORD (WITH CONN.) BR6
404 1-839-696-12 POWER-SUPPLY CORD (WITH CONN.) UC2/LA1
405 4-297-989-01 AC COVER BR6
405 4-299-531-01 AC COVER UC2/LA1
406 1-754-949-11 BT ANTENNA
407 1-859-007-11 SPEAKER BOX ASSY (L)
408 1-859-007-21 SPEAKER BOX ASSY (R)
409 4-546-824-01 BRACKET, SP (2L HWK) A UC2/LA1
410
409 4-546-466-01 BRACKET, SP BARE (2L HWK) BR6
410 1-798-510-31 SWITCH UNIT (SM-G-WW) UC2/LA1
410 1-798-510-41 SWITCH UNIT (SM-G-KIT) BR6
409
411 4-546-826-11 UNDER COVER (3L_HWK) A UC2/LA1
407 411 411 A-2068-961-A UNDER COVER (3L_HWK) A BR6
402
406
403
405
404
460 457
458 451
461
460 452
459
461
460
456
453
458
455
5-3-3. CONNECTORS
5-3-4. SCREWS
5-4. XBR-55X850C/855C/857C
5-4-1. SMART CORE (M,L) REF. No. PART No. DESCRIPTION MARK
601 4-547-392-01 CASE, BOTTOM (M) BR6
601 4-564-315-01 CASE, BOTTOM (M) except BR6
602 A-2066-088-A HSC3_S_M MOUNT
603 4-547-390-01 LIGHT, GUIDE BR6
608
603 4-564-313-01 LIGHT, GUIDE except BR6
604 4-547-389-01 PANEL, ORNAMENT BR6
604 4-564-312-01 PANEL, ORNAMENT except BR6
607 605 4-547-395-01 COVER, TOP BR6
605 4-564-317-01 COVER, TOP except BR6
606 4-547-397-01 BRACKET, WIFI BR6
606 4-564-318-01 BRACKET, WIFI except BR6
607 4-566-841-01 HEAT SINK L(SC)
606
608 1-458-853-11 WLAN/BT MODULE(11AC) except BR6
608 1-458-853-21 WLAN/BT MODULE(11AC) BRZ BR6
605
604
602
603
601
655
654
652
653
651
English
2015CL08-Data
Made in Japan
9-888-573-01 Sony Visual Products Inc. © 2015. 3
XBR-55/65X850C, 855C, 857C, 75X850C, 855C 205
APPENDIX-1
How to USB update
4:USB image is newer soft version. 4:USB image is not newer soft version.
Automatically show message and start update. Automatically show message and start update.
Please follow directions. Please follow directions.
Preparing for system software update. During the No newer version of the system software was found.
system software update, the TV will automatically Please remove the USB device and select “OK” to exit.
restart. Please do not remove the USB device until an
update complete message is displayed. The update may
take up to 30 minutes to complete.
5: finished
5: finished
Yes
Update to the latest
After AC Plug-in, wait for 30sec software version
then turn on TV by power key *Remove all signal
on TV or remote commander. connection.
(antenna, external input,
ether cable, etc)
*Insert the USB memory.
SMART CORE LED will
change to white blinking.
*After completes, TV will
Check condition
reboot by itself and turns on.
Is it the Case 1 or 2?
<Case2> *Disconnect the USB memory.
Panel : Picture appear
SMART CORE LED : White Lit
1.Take out panel from carton box with proper number of operator.
≧43” MINIMUM NUMBER OF
OPERATOR
XBR-55
HANDLING GUIDANCE
Unpacking(2/2)
Glass area
Glass area
HANDLING GUIDANCE
Carrying (1/2)
MINIMUM NUMBER OF
DO NOT HOLD PANEL HORIZONTALLY AT ALL TIMES. OPERATOR
XBR-55
2
1. Carry panel vertically.
AL BEZEL
Glass area
AL BEZEL
HANDLING GUIDANCE
Carrying (2/2)
MINIMUM NUMBER OF
OPERATOR
XBR-55
3. When carrying by only 1 person, hold panel at top and bottom center position.
2
≧49” ≧49”
HANDLING GUIDANCE
Placing to table
Follow guidelines below. MINIMUM NUMBER OF
OPERATOR
XBR-55
1. Steps to place panel to table. 2
(1) Place vertically. (2) Change hold position. (3) Place to table.
2. Place panel by 2 people. 3. Place panel within table 4. Table must not have any step.
surface.
STEP
HANDLING GUIDANCE
Others
1. Do not press panel during fixing screw. 3. When attaching or detaching
vacuum handling jig to panel,
maximum force on panel shall be
less than 100N total.
Glass area