Академический Документы
Профессиональный Документы
Культура Документы
GUIA PRÁCTICA
1. DATOS GENERALES
ASIGNATURA: TEC. DE COM. Y CODIGO DE LA CARRERA:
REDES II
CARRERA: ING. DE SISTEMAS
CURSO: A SEMESTRE: SEXTO
CONTENIDO ANALITICO: UNIDAD DIDACTICA:
8.1. Enrutamiento de estado de enlace. PROTOCOLOS DE ESTADO DE
8.2. Implementación de protocolos de ENLACE
estado de enlace.
8.3. Características de OSPF.
8.4. Configuración básica de OSPF.
8.5. Métrica de OSPF.
DOCENTE: ARIEL GRUICH ARRATIA e-mail: arielgruich@yahoo.es
BIBLIOGRAFIA A SEGUIR:
Tanenbaum, Andrew S, 1997, Redes de Computadoras, Prentice-Hall, México
PRÁCTICA: N° 10 TITULO: OSPF CON ÁREAS
MATERIAL DE APOYO: CARGA HORARIA:
Computadora 3 horas Académicas
Packet Tracer.
2. OBJETIVO
Implementar enrutamiento.
1
COMANDO GENERAL DEL EJÉRCITO
ESCUELA MILITAR DE INGENIERIA
“Mcal. ANTONIO JOSE DE SUCRE”
BOLIVIA
4. PROCEDIMIENTO
Paso 1:
Implementar el siguiente esquema:
Paso2:
Considerar nombre de red 99.0.0.0, bajo las siguientes consideraciones de redes LAN para
cada router:
Sub-Red 1: 25 hosts
Sub-Red 2: 30 hosts
Sub-Red 3: 35 hosts
Sub-Red 4: 66 hosts
Sub-Red 5: 130 hosts
Sub-Red 6: 250 hosts
Sub-Red 7: 100 hosts
Sub-Red 8: 50 hosts
Sub-Red 9-14: 10 hosts
Adicionalmente considerar subredes con 2 IPs para cada enlace router-router
Paso3:
Ejecutar procedimiento VLSM, asignar IPs a interfaces y redes en esquema, documentar y
llenar la siguiente tabla:
Paso 3:
Para la configuración de los 3 routers, se debe usar las Wildcards en lugar de la máscara de
Red. El wildcard es al contrario que la máscara de red. Para una máscara de red
255.255.255.0 le corresponde un wildcard de 0.0.0.255.
2
COMANDO GENERAL DEL EJÉRCITO
ESCUELA MILITAR DE INGENIERIA
“Mcal. ANTONIO JOSE DE SUCRE”
BOLIVIA
El enrutamiento OSPF necesita un Process ID. Este ID va desde 1 hasta 65535. En este
ejemplo se emplea el Process ID 1 en todos los routers.
ROUTERS (Celestes):
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 1
Router(config-router)#network x.x.x.x x.x.x.x area 1
ROUTERS (Violetas):
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 1
Router(config-router)#network x.x.x.x x.x.x.x area 2
ROUTERS (Azules):
Router>en
Router#conf t
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#router ospf 1
Router(config-router)#network x.x.x.x x.x.x.x area 3
ROUTER():
Router>en
Router#config
Configuring from terminal, memory, or network [terminal]? terminal
Enter configuration commands, one per line. End with CNTL/Z.
Router(config)#interface serial x/x
Router(config-if)#bandwidth 50
Router(config-if)#interface serial x/x
Router(config-if)#bandwidth 10000
Router(config-if)#
3
COMANDO GENERAL DEL EJÉRCITO
ESCUELA MILITAR DE INGENIERIA
“Mcal. ANTONIO JOSE DE SUCRE”
BOLIVIA
Paso 6:
Ejecutar paso 4 nuevamente, y elaborar tabla comparativa entre antes y después de configurar
ancho de banda, con estos resultados establecer Conclusiones de laboratorio