Академический Документы
Профессиональный Документы
Культура Документы
Lecture - 2
Fluid Statics
Fluid Statics means fluid at rest.
At rest, there are no shear stresses, the only force is the normal
force due to pressure is present.
Pressure is defined as:
“Force per Unit Area” Or
“The amount of force exerted on a unit area of a substance or
on a surface.”
This can be stated by the equation:
F dF
p (For Finite Area) p (For Infinite Area)
A dA
Units : N/m2(Pa), lbs/ft2 (psf), lbs/in2 (psi)
Example
A load of 200 pounds (lb) is exerted on a piston confining
oil in a circular cylinder with an inside diameter of 2.50
inches (in). Compute the pressure in the oil at the piston.
Solution:
Principles about Pressure
Two important principles about pressure were described by
Pascal, a seventeenth-century scientist:
1. Pressure acts uniformly in all directions on a small volume
of a fluid.
2. In a fluid confined by solid boundaries, pressure acts
perpendicular to the boundary.
Direction of fluid pressure on boundaries
Pressure at a Point is same in All direction
(Pascal’s Law)
1. Consider a wedge shaped element of fluid at rest.
2. Thickness dy (perpendic ular to plane of paper).
3. Let p Avg. pressure in any direction.
4. p x and p z are avg. pressure in horizontal and vertical direction.
5. Forces in y direction need not be considered because they cancel.
6. No tangentia l force is involved, since the fluid is at rest.
7. Equilibriu m Condition : Sum of the force components on element
in any direction must be equal to Zero.
8. Fx 0; p cos dl dy - p x dy dz 0
Since dz dl cos
Therefore;
p px
Pressure at a Point is same in All direction
1
9. Fz 0; p z dx dy - p dl dy sin dx dy dz 0
2
Neglecting 3rd term as weight is negligible.
Since dx dl sin
Therefore;
p pz
10. We can also proof p py by considering a three dimensional case.
Thus pressure at any point in a fluid at rest is same in all direction.
Variation of Pressure in a Static Fluid
(Hydrostatic Law)
It states:
“Rate of increase of pressure in vertical downward direction
must be equal to Specific Weight of fluid at that point.”
Variation of Pressure in a Static Fluid
(Hydrostatic Law)
1. Consider an element of static fluid.
2. Assume density of fluid to be constant w ithin the element
(Since the element is very small).
3. Pressure at the center of element is p.
4. Dimensions of element are x y and z.
5. Force acting in vertica l direction are :
a. Body force : the action of gravity on the mass within th e fluid.
b. Surface force : transmi tted from the surroundin g fluid.
6. If the forces are summed in the horizontal direction, that is x and y,
the only forces acting are the pressure forces on the vertical faces of
element.
7. To satisfy Fx 0 and Fy 0, the presssures on the opposite vertical
faces must be equal.
p p
8. Thus 0
x y
9. Summing forces in the vertical direction and putting it equal to zero.
p z p z
Fz p xy p xy xyz 0
z 2 z 2
After simplifica tion :
p
z
Since p is independen t of x and y, we can write above equation as :
dp
dz
This is the general expression that relates variation of pressure in a
static fluid to vertical position. The minus sign indicates that as z gets larger
(increasin g elevation) , the pressure gets smaller.
To evaluate the pressure anywhere in a fluid at rest, we must intergate previous
equation between appropriat e chosen limits.
dp dz
dp dz
p z
Say; z h
p h
Or
p
h (Pressure Head)
Pressure expressed in Height of Fluid
h 2 200mm 0.2m
s1 1 and s 2 13.6
Let h Pressure head of mercury in terms on head of water.
1. Let us consider t he vessel is to be empty and Z - Z be the datum line.
Pressure head in the right limb above Z - Z
s1h1 1xh h
Pressure head in the left limb above Z - Z
s 2 h2 13.6 x0.2 2.72m
Equating; h 2.72m
2. Consider t he vessel to be completely filled with wate r.
As a result, let the mercury level goes down by x meters in the right limb, and
the mercury level go up by the same amount in the left limb.
Therefore total height of water in the right limb
x h 3 x 2.72 3 x 5.72
Pressure head in the right limb 1(x 5.72) x 5.72
We know that manometer reading in this case :
0.2 2x
Pressure head in the left limb
13.6 (0.2 2x) 2.72 27.2x
Equating the pressures :
x 5.72 2.72 27.2x
x 0.115m
and manometer reading 0.2 (2x0.115) 0.43m 430 mm
Differential Manometer:
It is a device used for measuring the difference of pressures,
between the two points in a pipe, on in two different pipes.
It consists of U-tube containing a heavy liquid (mercury)
whose ends are connected to the points, for which the
pressure is to be found out.
Procedure:
Let us take the horizontal surface Z-Z, at which heavy liquid
and light liquid meet in the left limb, as datum line.
Let, h=Difference of levels (also known as differential
manomter reading)
ha, hb= Pressure head in pipe A and B, respectively.
s1, s2= Sp. Gravity of light and heavy liquid respectively.
Differential Manometer:
1. Consider figure (a):
2. Pressure head in the left limb above
Z-Z = ha+s1(H+h)= ha+s1H+s1h