Академический Документы
Профессиональный Документы
Культура Документы
2008 DD-7
SERVICE NOTES
Issued by RJA
Table of Contents
Cautionary Notes ..............................................................2 Verifying the Version Number........................................8
Main Specifications ...........................................................3 Performing a Factory Reset..............................................8
Location of Controls .........................................................4 Updating the System ........................................................8
Location of Controls Parts List........................................4 Test Mode ...........................................................................9
Exploded View ..................................................................5 Circuit Board (Main Board) ...........................................17
Exploded View Parts List.................................................5 Circuit Diagram (Main Board: Analog) .......................18
Parts List .............................................................................6 Circuit Diagram (Main Board: Digital) ........................20
Cautionary Notes
Before beginning the procedure, please read
through this document. The matters described may
differ according to the model.
No User Data
This product cannot save user data. Backing up user data during servicing is
not required.
Parts List
A component whose part code is ******** cannot be supplied as a service part
because one of the following reasons applies.
• Because it is supplied as an assembled part (under a different part code).
• Because a number of circuit boards are grouped together and supplied as
a single circuit board (under a different part code).
• Because supply is prohibited due to copyright restrictions.
• Because reissuance is restricted.
• Because the part is made to order (at current market price).
Circuit Diagram
In the circuit diagram, “NIU” is an abbreviation for “Not in Use,” and
“UnPop” is an abbreviation for “Unpopulated.” They both mean non-mounted
components. The circuit board and circuit board diagram show silk-screened
indications, but no components are mounted.
2
May. 2008 DD-7
Main Specifications
DD-7: Digital Delay
Input Impedance
1 MΩ
Weight
440 g / 1 lb (including battery)
Controls
* 0 dBu = 0.775 Vrms
Pedal switch
* In the interest of product improvement, the specifications and/or appearance of
E.LEVEL knob, F.BACK knob, D.TIME knob, MODE knob this unit are subject to change without prior notice.
Indicator
CHECK indicator
(Used for indication of TEMPO, HOLD, and to check battery)
Connectors
INPUT-A (MONO) jack, INPUT-B jack
OUTPUT-A (MONO) jack, OUTPUT-B jack
TEMPO/EXP jack, AC adaptor jack (DC 9 V)
Power Supply
DC 9 V:
Dry battery 6F22 (9 V) type (carbon)
Dry battery 6LR61 (9 V) type (alkaline)
AC Adaptor (PSA-series: optional)
Current Draw
55 mA (DC 9 V)
Expected battery life under continuous use:
Carbon: 1.5 hours
Alkaline: 6 hours
* These figures will vary depending on the actual conditions of use.
3
May. 2008 DD-7
Location of Controls
fig.panel.eps
4
May. 2008 DD-7
Exploded View
fig.bunkai.eps
10
b
11
a
a
7
b
6 d
2
12 1 9
5
c
8
5
May. 2008 DD-7
Parts List
fig.-part1-e.eps
NOTE: The parts marked # are new. (initial parts) The description "Q'TY" means a necessary number of the parts per one product.
CASING
22357305R0 BOTTOM BASE 1
22027851R0 BOTTOM COVER 1
# 75E593C0R0 CASE 1
# G2217798R0 PANEL PLATE 1
# 75E592T0R0 PEDAL 1
22357304R0 PEDAL PLATE 1
KNOB, BUTTON
# G2477127R0 ROUND KNOB D-CUT (BLUE/BLACK) 4
SWITCH
13129710R0 SWITCH(PUSH) JM-0404 1
PWB ASSY
# 75E593P0R1 MAIN SHEET ASSY 1
* This unit includes the following parts.
******** MAIN BOARD
******** VR BOARD
******** INPUT BOARD
******** CTL BOARD
******** LED BOARD
DIODE
F5029423R0 LED L-3VEGW 1
RESISTOR
F5399101R0 MTL.FILM RESISTOR 0J (1608TYPE) 12
# F5429516R0 MTL.FILM RESISTOR 1R0 J(1608TYPE) 12
POTENTIOMETER
F3279852R0 POTENTIOMETER RD901-20-15FW-B54-006 3
# F3229206R0 POTENTIOMETER RD901-20-15FW-B50K-08Q7 1
8CLIC
CONNECTOR
F3419102R0 BATTERY CONNECTOR 006P BATTERY SNAP 1
WIRING, CABLE
# F3487015R0 WIRING YELLOW 110X6EX6E (EXP) 1
H4009408R0 WIRING 1007 WHITE 85X6X3 1
# F3477063R0 WIRING RIBBON CABLE 6P X80MM 1
H4009498R1 WIRING 1P VIOLET L=160MM 1
# H4009305R0 WIRING ORANGE 100X3X6 (OUTPUT) 1
F3467053R0 WIRING 1007-26X3P L=65MM CONNECT X 1 1
# H4009610R0 WIRING GREY 100X3X6 (OUTPUT) 1
H4009499R1 WIRING 1P GREEN L=160MM 1
H4009597R0 WIRING 1007 BROWN 105X6X3 1
# H4009458R0 WIRING BLACK 45X6X6 (INPUT) 1
# F3467058R1 INPUT WIRING BOARD IN CONNECTOR 1
6
May. 2008 DD-7
SCREWS
H5039158R0 WASHER M9X14X0.5T NI 5
40125101 THUMB SCREW M3X10 FE ZC 1
40125134 NYLON WASHER 3X6X0.5 2
22137709R0 WASHER 9.6X14X1.0 1
# G2137403R0 WASHER HALF MOON SHAPE 1
H5019413R0 SCREW M3X10 BINDING MACHINE FEBC 2
H5029325R0 SCREW 3X6 B1FEBC 5
H5039205R0 TOOTH WASHER 9.1X13 5
H5039510R0 NUT M9X12X2T NI 5
H5039521R0 NUT M7 4
PACKING
G2627738R0 INNER BOX 1
# G2627793R0 PACKING CASE 1
MISCELLANEOUS
H2369451R0 LED SPACER LEDH-5 5MM 3P 1
G2537516R0 PSA CAUTION CE 9V N225 1
22177109R0 COIL SPRING 1
22267333R0 CUSHION 1
G2167301R0 INSULATING SHEET 1
22157702R0 PEDAL GUIDE BUSH 1
22257257R0 EARTH TERMINAL 2
ACCESSORIES (Standard)
# G6017474R0 OWNER’S MANUAL JAPANESE 1
# G2507366R0 OWNER’S MANUAL ENGLISH 1
# G2547154R0 MODE LABEL 1
# G2547160R0 APPLICATION LABEL 1
7
May. 2008 DD-7
3. Holding down the foot pedal and inserting a plug into the INPUT jack
makes the CHECK LED light up.
* Continue holding down the pedal until the LED goes dark.
After approximately 1 second the CHECK LED flashes, and the number
of flashes indicates the version.
1 flash: Ver. 1.00
2 flashes: Ver. 1.01
3 flashes: Ver. 1.02
8
May. 2008 DD-7
Test Mode
Items Required
• Oscillator x 2
• Oscilloscope x 1
• Noise meter x 2
• AC adaptor (PSA series device or 9 V DC power source) x 1
• Powered monitor x 2
• Expression pedal (EV-5) x 1
• 47-kΩ short plug x 2
Power
Supply
400Hz 400Hz
800mV 4.0V
Square Sine
9V
47kΩ
Dummy Plug
6.5V
EV-5
3. Holding down the foot pedal and inserting a plug into the INPUT jack makes the CHECK LED light up.
* Continue holding down the foot pedal until the LED goes dark.
After approximately 1 second the CHECK LED flashes, and the number of flashes indicates the version.
1 flash: Ver. 1.00
2 flashes: Ver. 1.01
flashes: Ver. 1.02
9
May. 2008 DD-7
Test Items 4. Adjust the E.LEVEL control to the 12 o’clock position. With the control
turned down counterclockwise all the way, turn it clockwise to the 12
1. VR Check (E.LEVEL) (p. 10) o’clock position, and verify that the CHECK LED goes dark. At the 12
2. VR Check (F.BACK) (p. 10) o’clock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
3. VR Check (D.TIME) (p. 11)
4. VR Check (MODE) (p. 12)
5. DA Check (EXP [Expression Pedal] Check) (p. 13)
6. DSP Through Check (INPUT B Check) (p. 14)
7. DSP Through Check (INPUT A Check) (p. 14)
8. DSP Through Check (OUTPUT A Check) (p. 15)
9. DSP Through Check (OUTPUT B Check) & CLIP Check (p. 15)
10. Residual Noise Check (p. 16)
11. Battery Operation Check (p. 16)
1. VR Check (E.LEVEL)
Make the connections shown below to the INPUT and OUTPUT jacks on the
DD-7, using the settings indicated.
INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p. 5. Turn the E.LEVEL control clockwise all the way. Verify that while the
INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p. control is being turned all the way clockwise from the 12 o’clock position,
OUTPUT A: Connect the oscilloscope. the CHECK LED stays dark. When the control has been turned clockwise
all the way, the LED lights up red.
OUTPUT B: Connect the oscilloscope.
fig.DD-7-wave-1.eps_75
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC.
1. Verify that the E.LEVEL control is turned down counterclockwise all the
way.
The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
2. VR Check (F.BACK)
Make the connections shown below to the INPUT and OUTPUT jacks on the
DD-7, using the settings indicated.
2. With the E.LEVEL control turned down counterclockwise all the way, INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p.
turn it clockwise to the 9 o’clock position. INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p.
Verify that the CHECK LED goes dark. OUTPUT A: Connect the oscilloscope.
3. Turning the control all the way counterclockwise again makes the OUTPUT B: Connect the oscilloscope.
CHECK LED light up red. Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC.
fig.DD-7-wave-2.eps_75
1. Verify that the F.BACK control is turned down counterclockwise all the
way.
The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
10
May. 2008 DD-7
2. With the F.BACK control turned down counterclockwise all the way, turn 3. VR Check (D.TIME)
it clockwise to the 9 o’clock position.
Verify that the CHECK LED goes dark. Make the connections shown below to the INPUT and OUTPUT jacks on the
DD-7, using the settings indicated.
3. Turning the control all the way counterclockwise again makes the
INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p.
CHECK LED light up red.
fig.DD-7-wave-2.eps_75
INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p.
OUTPUT A: Connect the oscilloscope.
OUTPUT B: Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC.
1. Verify that the D.TIME control is turned down counterclockwise all the
way.
The CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
4. Adjust the F.BACK control to the 12 o’clock position. With the control
turned down counterclockwise all the way, turn it clockwise to the 12
o’clock position, and verify that the CHECK LED goes dark. At the 12
o’clock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
2. With the D.TIME control turned down counterclockwise all the way, turn
it clockwise to the 9 o’clock position. Verify that the CHECK LED goes
dark.
3. Turning the control all the way counterclockwise again makes the
CHECK LED light up red.
fig.DD-7-wave-2.eps_75
5. Turn the F.BACK control clockwise all the way. Verify that while the
control is being turned all the way clockwise from the 12 o’clock position,
the CHECK LED stays dark. When the control has been turned clockwise
all the way, the LED lights up red.
fig.DD-7-wave-1.eps_75
4. Adjust the D.TIME control to the 12 o’clock position. With the control
turned down counterclockwise all the way, turn it clockwise to the 12
o’clock position, and verify that the CHECK LED goes dark. At the 12
o’clock position, the LED lights up red.
fig.DD-7-wave-3.eps_75
11
May. 2008 DD-7
5. Turn the D.TIME control clockwise all the way. Verify that while the 3. Adjust the MODE knob to the MODULATE position.
control is being turned all the way clockwise from the 12 o’clock position, Verify that waveforms like those shown in the figure below are output.
the CHECK LED stays dark. When the control has been turned clockwise The CHECK LED lights up orange.
all the way, the LED lights up red. fig.DD-7-wave-1.eps_75
fig.DD-7-wave-1.eps_75
12
May. 2008 DD-7
6. Adjust the MODE control to the 200 ms position. 5. DA Check (EXP [Expression Pedal]
Verify that waveform output stops.
The CHECK LED goes dark.
Check)
fig.DD-7-wave-2.eps_75 Make the connections shown below to the INPUT and OUTPUT jacks on the
DD-7, using the settings indicated.
INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p.
INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p.
OUTPUT A: Connect the oscilloscope.
OUTPUT B: Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC.
4. Depress the toe of the EV-5 pedal, and stop when the intermediate
position is reached.
Verify that the CHECK LED is lighted up green.
fig.DD-7-wave-3.eps_75
13
May. 2008 DD-7
5. Depress the toe of the EV-5 pedal all the way. 3. Insert the plug into the INPUT B jack.
Verify that the CHECK LED is lighted up red. Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75 fig.DD-7-wave-1.eps_75
INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p. INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p.
INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p. OUTPUT A: Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. 1. Adjust the MODE control to the 50 ms position.
1. Adjust the MODE control to the 200 ms position. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-1.eps_75
Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75
2. Disconnect the plug from the INPUT B jack. Verify that the CHECK LED lights up red.
fig.DD-7-wave-5.eps_75
Verify that the CHECK LED lights up green.
fig.DD-7-wave-4.eps_75
14
May. 2008 DD-7
3. Insert the plug into the INPUT A jack. 3. Insert the plug into the OUTPUT A jack.
Verify that the CHECK LED lights up orange. Verify that the CHECK LED goes dark.
fig.DD-7-wave-1.eps_75 fig.DD-7-wave-1.eps_75
8. DSP Through Check (OUTPUT A Check) 9. DSP Through Check (OUTPUT B Check)
Make the connections shown below to the INPUT and OUTPUT jacks on the & CLIP Check
DD-7, using the settings indicated.
Make the connections shown below to the INPUT and OUTPUT jacks on the
INPUT A: Input a rectangular wave at 400 Hz, 800 mVp-p. DD-7, using the settings indicated.
INPUT B: Input a rectangular wave at 400 Hz, 800 mVp-p. INPUT A: Input a sine wave at 400 Hz, 4.0 V p-p.
OUTPUT A: Connect the oscilloscope. INPUT B: Input a sine wave at 400 Hz, 4.0 V p-p.
OUTPUT B: Connect the oscilloscope. OUTPUT A: Connect the oscilloscope.
Set the oscilloscope to 500 mV/DIV, 1 ms/DIV, and coupling: DC. OUTPUT B: Connect the oscilloscope.
1. Adjust the MODE control to the HOLD position. Set the oscilloscope to 2.0 V/DIV, 1 ms/DIV, and coupling: DC.
Verify that the CHECK LED has gone dark. 1. Adjust the MODE knob to the MODULATE position.
fig.DD-7-wave-1.eps_75
Verify that the CHECK LED lights up orange.
Verify that the waveforms are not clipped.
fig.DD-7-wave-7.eps_75
15
May. 2008 DD-7
3. Insert the plug into the OUTPUT B jack. 6. Insert the plug into the OUTPUT B jack.
Verify that the CHECK LED lights up orange. Verify that the CHECK LED lights up orange.
fig.DD-7-wave-7.eps_75 fig.DD-7-wave-7.eps_75
4. Adjust the MODE knob to the ANALOG position. 7. Adjust the MODE control to the REVERSE position.
Verify that the CHECK LED lights up orange. Verify that the CHECK LED lights up orange.
Verify that the waveforms are not clipped. Verify that the waveforms are not clipped.
fig.DD-7-wave-7.eps_75 fig.DD-7-wave-7.eps_75
3. Detach the plugs from the INPUT A and INPUT B jacks and switch off
the power.
16
May. 2008 DD-7
17
May. 2008 DD-7
INPUT BOARD
PWB F2927058R0 4/6
1SS362FV(TPL3)
D6
UnPop AVCC C6 ; Unpop -> 10/10
1 2 TP26
ASSY 75E593P0R0
Q1
1 R61; Unpop
R70; 0
-> 39k
-> 39k
6 BRN 60mm AGND
3
2
2SK880-GR(TE85R,F)
INPUT A
7 TP65 3
8 TP2 R70
4 R30 C77
1 39k
3 YEL 70mm 10k
1
2 TP76 1uF
TP30 2 _BYPASS_A
1
D (0.5%)
JK1 TP31 1 C6 R61 1 3
2LJ-650NHW00 10uF 10V 39k IC4
UnPop
R57
R19
NJM4558M(TE1)
10k
IN_REFV
1M
SHASSIS TP8
AVREF
6
7 TP67
8
R42
TP70 AGND
4 TP83
INPUT B
2SK880-GR(TE85R,F)
SHASSIS C5 39k IC4
AGND 1SS362FV(TPL3) 10uF 10V NJM4558M(TE1) C133
TP68 UnPop
AVREF
AVCC 68pF
TP79 1 2
BLK 45mm C13; 10(3216) -> 10/10
VDD
8
C14; 10(3216) -> 10/10
TP28 2 R49 C24
0.1uF
C15; 10(3216) -> 10/10
AGND
C34
GRN 60mm C18; 10(3216) -> 10/10
TP73 3 IC4 C64; 1u -> 10/10 22k 220
VEE
R25 TP51 NJM4558M(TE1) D (0.5%)
4
C78
Q2
10k
1
ORG 70mm 1uF R81
TP66 TP60 56k
AGND R48
22k D (0.5%)
D (0.5%)
TP39 D (0.5%) 2
R59
R28
10k
IN_REFV
1M
C59 A+3.3
AVCC 47pF TP27
2 3
D (0.5%) 10V C18 AVREF
R52 R45 10uF 10V
AGND 10uF C23 22k 22k 2
C15
IC5
C8 2200pF D (0.5%) D (0.5%) NJM4558M
R21
10uF 10V
R43
R1
10k
IN_REFV 2
10
0
1
DA_A
10uF 10V
TP37 R82 3 C7
56k 100uF 4V C127
D (0.5%) IC1 C9
D (0.5%)
NJM2115V(TE1)
0.1uF
R20
C43
12k
R50 C22
R100 C31 C45
5
4
C2 C58 AGND 0.1uF 0.1uF AGND 22k 2200
AGND UnPop 47pF TP12 D (0.5%)
10uF 10V 10V TP33
VD
VA
R51 R46 2 19 R79
10uF C21
2200pF D 22k 2 22k LIN LOUT R47 56k
C10 (0.5%) C13 D (0.5%) 22k D (0.5%)
D+3.3 10uF 10V 6 D (0.5%)
R80 _AD_B 7 1 20 DA_B 6
A+3.3 56k 5 RIN ROUT 7
13 8 5
D (0.5%) IC1 <2F5> SD_DA SDTI SDTO 2
AVREF
R92 C14 IC5
D (0.5%) D (0.5%)
0 16 MCLK
<2E5> BCK
10k
BCLK SD_AD
10uF 10V
7 <2F5> A
TP11 6 DEM1
C41 0.1uF
DEM0
C11
VDD
8
D (0.5%)D (0.5%)
0.1uF
17 18
<2C7> CODEC_PDN
C29
R22
PDN VCOM
C27 0.1uF
AVREF
R23
2
10k
VEE VDD
10k
12
8
C37 0.1uF
C64 10uF 10V
11 CKS3
VEE
IC1 10 CKS2
C32 0.1uF
NJM2115V(TE1)
4
C4 9 CKS1
10uF 10V AGND
VSS
CKS0
R101
4
12k
D+3.3 AGND IC6
D1 AK4552VTP
3
1SS362FV(TPL3)
2 1 C3
AGND
TP49 C38 10uF 10V
3
R16
0.1uF
22k
C130 TP4
R15 0.1uF AGND DGND
1k TP4
D2 C129
1SS362FV(TPL3) 0.1uF AVCC AVCC
DTC114TUAT106
DTC114TUAT106
2 1 1
C128
Battery 006P 0.1uF R7
3
R5
R13
56k
56k
22k
C66 0.047uF
C67 0.047uF
IN_A_DET <2C7> Q6 ; Unpop -> DTC114TUAT106
IN_B_DET R58
Q6
Q8
<2C7> R7 ; Unpop -> 56k R53
3
R11 1 R58; Unpop -> 1M
1 1
1M
1k 1M
2SC4116-GR(TE85R,F)
2
TP23
TP43
TP52
TP24
TP64
1
C49 0.1uF
5
100uF
TP74 4
C57
16V
C55 FB_1.5
47uF 10V FB_3.3 <G10>
10uF 10V
0.1uF
D13
0.1uF
C30
GS1G <G10>
C42
C74
BLU 70mm
TP80
D14
AGND 4 Digital 3.28->3.13
R38
Connect to SHASSIS
D (0.5%)D (0.5%)
1 TP35
R93
R75
2.2k
TER1
0
EARTHTERMINAL TP1
D (0.5%)
10k D (0 5%)
1
27k D (0.5%)
27k D (0.5%)
R95
47k
R96
TER2 TP45
18k
C53 1000pF
C51 1000pF
R83
R18
2SC4117-GR(TE85L,F)
D (0.5%)
3 2
R72
R74
R31
D (0.5%)
47k
470pF 47k
560
C40 0.1uF
R44
22k
R94
47k
C54
10uF 10V
470pF
C52
C50
2 47uF 10V
C73
R3
39k
LED BOARD
3
TP3 1 D15
PWB F2927058R0 3/6 UDZS TE-17 9.1B DGND
Q17
2
R17 22k
<2C7>
TP48 22k TP40
Q19
2SA1586-GR(TE85R,F)
R91
UnPop
UnPop
39k
R98
R97
RIBBONCABLE 3P
18
May. 2008 DD-7
fig.d-main-analog.eps@R
2SK879-Y(TE85L,F)
C17; Unpop -> 10u(3216) TP44
D9 ; Unpop -> 1SS387
Q12; Unpop -> 2SK879-Y C61
R64; Unpop -> 39k 68pF
1 R35; Unpop -> 470k
R68
TP21 39k
TP22 OUTPUT A
Q12
1
C76
2 10uF 16V TP81 GRY 100mm JK5
R64 1 2 HTJ-064-14D
C62 22pF
1 C17 1 1 39k 2 1 3 IC3 3
10uF R85 1
3
NJM4558M(TE1)
R35
470k
1k TP69
R90
BRN 105mm
AVREF
100k
1 AVREF
D9 SHASSIS
1SS387(TPH3,F)
TP32
TP55
AGND
_DA_A
R63 2 1
C16 39k Q9
AVREF
TP36 10uF
3
R33
2SK879-Y(TE85L,F)
470k
D10
1SS387(TPH3,F)
4
00pF
TP14
C75 OUTPUT B
Q11 10uF 16V R88 WHT 85mm JK6
UnPop TP82 2 HTJ-064-14D
1 3
1k 1
2 1
R89
R66
100k
TP25 TP72
(TE1) D8 C60
UnPop 68pF
AGND
TP46 R67
39k
Q13
2SK879-Y(TE85L,F)
6
7
22pF
R65 2 1 5
C20
1SS387(TPH3,F)
39k IC3
10uF
3
R32
0pF NJM4558M(TE1)
470k
TP53 AVREF
D11
C63
AVREF
TP10
C19
10uF TP5
_DA_B
R69 AVCC
5 39k 2 1
558M(TE1) Q10
3
R34
2SK879-Y(TE85L,F)
470k
AVREF
VEE VDD
C35 0.1uF
8
AVCC D7
1SS387(TPH3,F) IC3
NJM4558M(TE1)
NJM4558M(TE1)
4
VEE VDD
AGND
IC5
D
D5 D+3.3
1SS362FV(TPL3)
1 1 2
TP13 TP15
TP16
3
TP29
R9
AVCC AVCC
22k
DTC114TUAT106
DTC114TUAT106
AVCC
UnPop
R4
R10
56k
R2
56k
R6
1k
C65 0.047uF
0.047uF
UnPop
D3
C69 UnPop
1SS362FV(TPL3)
Q7
Q4
Q5
1 UnPop 1 1M 1 1M
DGND
3
C68
R12
2
22k
<2C7> OUT_A_DET
DGND AGND OUT_B_DET
DGND AGND DGND AGND <2C7> R14
1k
TP34
PVCC
Q14
C56 QS5U27TR(PB FREE)
18
3
15 D+1.5
16 FB1
TP62
INV1 C44
13 0.1uF
2
C70 DTC1 12
3
4 8 FB_1.5
R29 NON2 PVCC2 9 <F6>
19 OUT2
TP50
100uF 4V
D (0.5%)
0.1uF
C25
D (0.5%)
R77
SEL1 D+3.3
R26
R99
56
TP57
15k
2
2
3
3 RT 1
R41
CT 10 TP47
PGND
0
14 L1
4
SCP
5
ELL6SH151M
17 DGND FB_3.3
GND
VREF <F6>
TP56
100uF 4V
0.1uF
Q15
C39
C26
C48 IC2
C72 QS5U27TR(PB FREE)
20
0.1uF BD9851EFV-E2
TP63 470pF Q15
QS5U27TR(PB FREE)
C28 R27
0.1uF 10k D (0.5%) DGND
DGND
3
1 RST_DCDC <2B4>
Q3
2
DTC114TUAT106
19
May. 2008 DD-7
TP95
TC7W04FK(TE85L/F)
PWB F2927058R0 5/6 IC10
ASSY 75E593P0R0 TC7W04FK(TE85L/F)
RESET 1 7 6 2 TP
10k
10k
10k
10k
<E5> C87
JK4 100uF 4V
HTJ-064-12DS 3
2 TP109 YEL 110mm 3 5 RST_DCDC
R114
R120
R115
R119
3 <1H7> 8 A2 2
1 A1
VCC 1 C121 0.1uF
TP116 GRY 110mm IC10 A0
TC7W04FK(TE85L/F) C122 5 C91 0.1uF
D+3.3 0.1uF 4 SDA 6 C109 0.1uF
SHASSIS VSS SCL 7 WP_USER
WP <E5> C101 0.1uF
TP102
IC12 C112 0.1uF
HN58X2402SFPIBEZ
GND VCC
8
C119 0.1uF
C116 IC10 3 C104 0.1uF
TP99
TP96
0.1uF TC7W04FK(TE85L/F) 8 NC 2
PWB F2927058R0 2/6 VCC A1 1 C103 0.1uF
4
VR BOARD ASSY 75E593P0R0 C105
0.1uF
A0
SDA
5 SDA <C8>
C107
C114
0.1uF
0.1uF
4 6 SCL <C8>
DGND VSS SCL 7 WP_PROG C110 0.1uF
_DVREF WP <C8> C98 0.1uF
IC8
9
HN58X24512FPIE TP106
DGND
ADRESS->USER;1010001/PROG;1010X00
3
VR1
RD901F-20-15FW-B50K-006 DGND
2 E.LEVEL D+3.3 79
DVREF D17 80 SCL
1
1SS362FV(TPL3) SDA
2 1
TP117 102
D16 TP119 103 DCK
3
1SS362FV(TPL3) TP121 104 DMS
TP122 105 DDI
R136
3
VR2 2 1
R105
4.7k
TP118 106 DDO
470k
RD901F-20-15FW-B50K-006 ESC+3.3 _DRST
R103 DVREF TP87
3
2 F.BACK R133 R134 10 84
DGND
1
VR3 94
TP101
AVREF
TP103
TP104
TP98
TP89
TP88
RD901F-20-15FW-B50K-006 DVREF C85 R132 R135 R107
C88 93
10uF 10V 4.7k 4.7k
2 D.TIME 0 92 AIN7
10uF DGND DGREF
1
1 1 91 AIN6
2 2 90 AIN5
3 3 89 AIN4
4 4 88 AIN3
3
VR4 5 5 87 AIN2
RD901F-20-15FW-B50K-08Q7 6 6 86 AIN1
AIN0
0.01uF
0.01uF
0.01uF
0.01uF
TP100
DGND ESC+1.5
2 MODE(8click)
0.1uF
CN4 RIBBON CABLE 6P CN3 R102
C124 1000pF
1
C82
C80
C83
C81
_DGREF R108 0 AGND1
TP97
139
XIN
2
D+3.3 C125
PVCC DGREF 22pF
X1 140
1
DGND XOUT
C126 ESB16.9344F16D35F
R104
56k
22pF 98
1 R131 99 TMODE
TP84
5 4 0 137 TMC2
VDD VOUT 142 _TRST
SUB
3 1 143 SMC
2 R124 GND ER C123
UnPop
AMC
R131; 15K (MF) -> 0
UnPop
81
C12
DGND
2
<1E5> PWM/S
BYPASS_B_MUTE 118
1 8 <1F5> _SYNC
2 7 110
<1D5> MCK 3 6 111 MCK/T
<1D5> BCK LRCK 4 5 107 BCK/T
<1D5> RA8 LRCK/
SD_DA 112
<1D5> SD_AD 100 113 SD7/T
<1D6> 116 SD6/T
117 SD5/T
<1F5> BYPS_A_TO_B_MUTE SD4/T
20
May. 2008 DD-7
fig.d-main-digital.eps@R
D+3.3 D+1.5
FBMA-10-160808-601T
FBMA-10-160808-601T
L6
ESC+3.3
86
L5
ESC+1.5
TP91 C86
100uF 4V
C113 0.1uF
C117 0.1uF
C118 0.1uF
C94 0.1uF
C100 0.1uF
C108 0.1uF
C96 0.1uF
9
17
26
34
49
61
82
96
114
122
132
144
36
41
55
72
101
108
141
DGND
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
EVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
IVDD
For UPDATE
121 DA_B_MUTE ESC+3.3
_CS4/SD0/TRR0/P80 68 <1F5> CN5
_CS3/P63 69 1 UnPop
_CS1/SPICS/P62
124
A23/_SYNC/TRS7/P97 125
<B5> SDA
<B5> SCL
2
3
4
SW BOARD
IN_B_DET 5 ESC+3.3
A22/TRS6/P96 126 IN_A_DET <1E4> 6 PWB F2927058R0 6/6
A21/TRS5/P95 127 OUT_B_DET <1E4> <B5> WP_PROG ASSY 75E593P0R0
A20/TRS4/P94 128 OUT_A_DET <1E8>
A19/TRS3/P93 129 LED_CHK_GRN <1E8>
R126
DGND
100k
AD13/SPIDI/P55 57
C79
AD11/BUCK/P53 59
R118 10k
AD10/BULCK/P52 60
AD9/BUDO1/P51 63
AD8/P50
1
43 EA(7)
AD7/P47 44 EA(6) DGND
AD6/P46 45 EA(5) TP111,TP114
AD5/P45 46 EA(4)
AD4/P44 47 EA(3)
5 AD3/P43 48 EA(2)
AD2/P42 51 EA(1)
AD1/P41 52 EA(0)
AD0/P40
5
R117 10k
R123 10k
10k
10k
10k
10k
64
ALE/P67 65
R116
R121
R122
R113
_CRD/P66 66
_CWR/P65 67
_WAIT/P64
120 DA_A_MUTE DGND S_ED(0:7)
INT2/SD1/TRR1/P81 78
INT1 <1E5>
1
0 22 4 5 S_EA(9)
EA13/_CRD/P10 24 3 6 RA3 S_EA(12)
EA12/_WAIT/P22 21 2 7 47 S_EA(8) 53 S_ED(7)
EA11/ALE/P11 28 1 8 S_EA(10) S_EA(12) 20 DQ15 51 S_ED(6)
EA10/_CS1/P20 23 S_EA(13) 21 BA0 DQ14 50 S_ED(5)
EA9/_CWR/P23 25 36 BA1 DQ13 48 S_ED(4)
EA8/_CS3/P21 29 EA(7) 4 5 S_EA(7) S_EA(11) 35 NC DQ12 47 S_ED(3)
EA7/AD15/P37 31 EA(6) 3 6 RA4 S_EA(0) S_EA(10) 22 A11 DQ11 45 S_ED(2)
T EA6/AD13/P35 33 EA(5) 2 7 47 S_EA(6) S_EA(9) 34 A10/AP DQ10 44 S_ED(1)
EA5/AD11/P33 39 EA(4) 1 8 S_EA(1) S_EA(8) 33 A9 DQ9 42 S_ED(0) D+3.3
EA4/AD9/P31 40 EA(3) S_EA(7) 32 A8 DQ8 13 S_ED(0)
P61 EA3/AD8/P30 38 EA(2) 4 5 S_EA(5) S_EA(6) 31 A7 DQ7 11 S_ED(1)
P60 EA2/AD10/P32 32 EA(1) 3 6 RA6 S_EA(2) S_EA(5) 30 A6 DQ6 10 S_ED(2)
P76 EA1/AD12/P34 30 EA(0) 2 7 47 S_EA(4) S_EA(4) 29 A5 DQ5 8 S_ED(3)
P75 EA0/AD14/P36 1 8 S_EA(3) S_EA(3) 26 A4 DQ4 7 S_ED(4)
S_EA(2) 25 A3 DQ3 5 S_ED(5) L4
2 4 5 S_ED(7) S_EA(1) 24 A2 DQ2 4 S_ED(6)
S_EA(0:13)
ED5/P05 5 47 2 7 S_ED(5)
D2/TRR2/P82 ED4/INT2/P04 6 1 8 S_ED(4)
4 5 S_ED(3) 19 27 TP93
ED3/_CS6/P03 7 RA2 3 6 S_ED(2) 18 _CS VDD 14
ED2/_CS4/P02 8 47 2 7 S_ED(1) 17 _RAS VDD 1
/SD3/TRR3/P83 ED1/A23/P01 11 11 88 S_ED(0) 16 _CAS VDD 49
ED0/A22/P00 S_EA(13) 39 _WE VDDQ 43
RCKI/P71 2 7 S_EA(11) 15 UDQM VDDQ 9
C92 0.1uF
C120 0.1uF
C106 0.1uF
C97 0.1uF
C99 0.1uF
C102 0.1uF
C95 0.1uF
IGND
IGND
IGND
IGND
IGND
IGND
47 4 5 VSS 28
VSS
IC7
115
123
100
109
138
IC9
10
18
27
35
50
62
83
97
37
42
73
UPD800402GJ-211-UEN-A(ESC) K4S641632K-UC75000
1
DGND
1
DGND TER3 C132
UnPop UnPop
1
TER4 C131
Connect to SHASSIS UnPop UnPop
DGND
21
May. 2008 DD-7
22
May. 2008 DD-7
23
May. 2008 DD-7
MEMO