Академический Документы
Профессиональный Документы
Культура Документы
CONSTRUCTION FEATUBES
Ballast Housing-The die cast aluminum housing provides a glare control and cutoff of the light pattern and also secures an
counterbalanced mounting, excellent heatdissipation, and optional internally installed concentric louver assembly. The
ease of maintenance. The pivotal axis and mounting location lens is clear, tlat, heat-resistant and tempered, high strength
of the trunnion (yoke) attachment allows even distribution of glass. The hinged stainless steel lens frame and one-piece
the assemblies' wejght, lor maximum counterbalance with a silicone rubber gasket is secured to the reflector with captive
minimurn of lifting force, throughout the unit's full aiming range. stainless stee{ hardware to ensure a fully sealed optical
The ballast and capacitor mounting arrangement provide system. An optionai heavy duty housing can be supplied for
maximum heat conductivity to the outer surfaces of the maximum ref lector protection.
housing for cooler operation of all electrical components. A lndex and Mounting-All units are equipped with a vertical
weatherprool and thermally controlled cable strain relief degree calibrated quadrant plate and repositioning device. A
connector allows use of 75'C rated cords. All luminaires are single index bolt seats quadrant plate and provides a positive
equipped with three foot length #14 AWG/3 conductor type reposilioning stop, returning luminaire to original aiming angle.
SOW-A cord. A rear housing cover, held in place by (4) captive A .250" thick steel trunnion (yoke) bracket is secured by two
stainless steel screws, can be hinged to fully expose all pivot locking bolts. Optional crossarm mounting fitting with
electrical components for visual inspection or maintenance, horizontal degree scale or a 2" pipe slipfitter assembly is
and is completely removable if necessary. A .125" thick available. All integral models have built-in visual aiming sights.
aluminum mounting bridge is provided on all remote models in
lieu of the integral ballast housing. An aluminum wiring and Lampholders-Enciosed glazed porcelain socket with spring
splice box, pre-wired with 3'length cord, is included. The loaded, nickel-plated center contact and reinforced lamp grip
prewired junction box is designed to provide cooler operation screw shell. An optiional lamp grip device, factory installed, is
and use of 75"C temperature rated cord. Junction box will also also available to increase lamp grip and centering support of
serve as handle ro pivot ruminaire during aining process. the glass envelope.
Socket Housing-A unique die cast aluminum socket Finish-Ballast socket housings and trunnion have a gray
housing is attached to ballast housing at three points. A half baked-on paint tinish.
inch air space separation minimizes any heat transfer between Lamp-Accommodates the following H.l.D. sources: Metal
socket housing and ballast components. Each socket housing Halide-1000W and 1500W; High Pressure Sodium-1000W
is equipped with a permanently sealed breather to stabilize lntegral Ballast Starting rated to 20'F. l\.4etal Halideand
atmospheric pressure changes during heatjng and cooling High Pressure Sodium ballasts are HPF constant wattage
cycles of the luminaire. All air displacement is filtered and free autotransformer (CWA) type. High Pressure Sodium ballasts
of any pollutants that would normally contaminate the optical utilize an electronic starter circuit.
assembly.
Optical Assembly-21 " diameter reflectors are anodized to
provide NEl./A Type 2,3,4,5 or 6 beam spreads. The reflectors
are spun aluminum, end punched and sphero-parabolic
shapes. The retlector lace is extended with a 2" engraved
J.H.SPAI.'LUNG
Subsidiary ol Kidde lnc.
811
ISOFOOTCAN DLE CU RVES (ronrzorurar)
LUl,4lNAlRE SERIES: CNll-1 000-i,4-1 5 LU|\illNAlRE SERIES: CNll-1 000-HPS-1 5
LAIMP: 1000W METAL HALIDE (CLEAR) LAMP: 1000W HIGH PRESSURE SODIUM
RATED LUTMENS: 100,000 RATED LUI'.4ENS: 1 30,000
DISTANCE : DISTANCE
RATIO = RATIO
MOUNTING HEIGHT MOUNTING HEIGHT
This rcpott has been prcparcd in accotdance with IES guides on testing procedures. lt is representative af luminaires tested under standardized and
stabilized laborctoty conditions. Vatious operating factos can cause differences between laboralary data and actualfield performance.
ACCESSORY GROUP:
The following accessor es rirust be ordered separate y:
983