Sikaflex®-291i Multifunctional adhesive sealant for marine application
Technical Product Data
Chemical base 1-C polyurethane 1 White, grey, black, Colour (CQP 001-1) brown Cure mechanism Moisture-curing Density (uncured) (CQP 006-4) depending on colour 1.3 kg/l approx. Non-sag properties Good Application temperature ambient 10 - 40°C (50 - 105°F) 2 Tack free time (CQP 019-1) 60 min. approx. 2 Open time (CQP 526-1) 45 min. approx. Curing speed (CQP 049-1) (see diagram) Shrinkage (CQP 014-1) 2% approx. Shore A-hardness (CQP 023-1 / ISO 868) 40 approx. Tensile strength (CQP 036-1 / ISO 37) 1.8 MPa approx Industry
Elongation at break (CQP 036-1 / ISO 37) 700% approx.
Tear propagation resistance (CQP 045-1/ ISO 34) 7 N/mm approx Glass transition temperature (CQP 509 -1/ ISO 4663) -45°C (-50°F) approx. Service temperature (CQP 513-1) -40 - 90°C (-40 - 195°F) Short term 4 hours 120°C (250°F) 1 hour 140°C (285°F) Shelf life (storage below 25°C) (CQP 016-1) 12 months 1) 2) CQP= Corporate Quality Procedure 23°C / 50% r.h.
Description Product Benefits Areas of Application
® ® Sikaflex -291i is a non-sag 1-C - Wheelmark approved Sikaflex -291i is a multipurpose polyurethane sealant specifically - 1-C formulation product used in marine con- developed for the marine market, - Highly elastic structions. It is suitable for making which cures on exposure to - Low odour elastic, vibration-resistant joint atmospheric moisture and forms a - Non-corrosive seals, and can also be used for a ® durable elastomer. Sikaflex -291i - Can be over painted variety of interior and exterior ® meets in addition the low spread of - Bonds well to a wide variety of sealing applications. Sikaflex -291i flame requirements set out by the marine substrates bonds extremely well to the ma- International Maritime Organisation - Solvent free terials commonly used in marine (IMO). - Very low VOC construction like wood, metals, ® Sikaflex -291i is manufactured in metal primers and paint coatings accordance with the ISO (2-C systems), ceramic materials 9001 / 14001 quality assurance and plastics (GRP, etc.). ® system and with the responsible Sikaflex -291i must not be used to care program. seal plastics that are prone to stress cracking (e.g. PMMA, PC, etc.). This product is suitable for experi- enced professional users only. Test with actual substrates and conditions have to be performed to ensure adhesion and material compatibility. Sikaflex® -291i 1 / 2 Cure Mechanism Do not apply at temperatures Packaging Information ® below 10°C or above 40°C. The Sikaflex -291i cures by reaction Tube 100 ml with atmospheric moisture. At low optimum temperature for substrate and sealant is between 15°C and Cartridge 300 ml temperatures the water content of the air is generally lower and the 25°C. 400 ml Unipack curing reaction proceeds slower 600 ml Tooling and finishing (see diagram 1). Tooling and finishing must be carried out within the tack-free time Value Bases 12 Thickness of cure [mm] 23°C (73°F) / 50% r.h. of the sealant. We recommend the All technical data stated in this ® 10 use of Sika Tooling Agent N. Product Data Sheet are based on 8 Other finishing agents or lubricants laboratory tests. Actual measured must be tested for suitability / com- data may vary due to circumstan- 6 10°C (40°F) / 50% r.h. patibility. ces beyond our control. 4 Removal 2 ® Health and Safety Information Uncured Sikaflex -291i can be 0 removed from tools and equipment For information and advice re- 0 2 4 6 8 10 12 ® garding transportation, handling, Time [days] with Sika Remover-208 or an- other suitable solvent. Once cured, storage and disposal of chemical Diagram 1: Curing speed for Sikaflex -291i ® the material can only be removed products, users shall refer to the mechanically. actual Material Safety Data Sheets Chemical Resistance Hands and exposed skin should be containing physical, ecological, ® washed immediately using Sika ® toxicological and other safety-re- Sikaflex -291i is resistant to fresh lated data. water, seawater, and proprietary Handclean towels or a suitable aqueous cleaning agents; industrial hand cleanser and water. Do not use solvents! Legal Notes temporarily resistant to fuels, min- The information, and, in particular, the eral oils, vegetable and animal Overpaintability ® recommendations relating to the appli- fats; not resistant to organic acids, Sikaflex -291i can be overpainted cation and end-use of Sika products, concentrated mineral acids and with most conventional paint are given in good faith based on Sika's caustic solutions or solvents. systems. The paint must be tested current knowledge and experience of The above information is offered for compatibility by carrying out the products when properly stored, for general guidance only. Advice preliminary trials and the best handled and applied under normal on specific applications will be conditions in accordance with Sika's results are obtained if the sealant recommendations. In practice, the given on request. is allowed to cure fully first, differences in materials, substrates and especially in the case of baked actual site conditions are such that no Method of Application enamels. Please note that non warranty in respect of merchantability Surface preparation flexible paint systems may impair or of fitness for a particular purpose, the elasticity of the adhesive, nor any liability arising out of any legal Surfaces must be clean, dry and relationship whatsoever, can be in- free from grease, oil and dust. The impair joint movement and lead to ferred either from this information, or adhesion of the sealant can be cracking of the paint film. from any written recommendations, or improved by wiping the joint with PVC based paints and paints that from any other advice offered. The user ® dry by oxidation (oil or alkyd resin an appropriate Sika activating of the product must test the product’s ® based) are generally not suitable to suitability for the intended application agent and Sika Primer if required. ® overpaint Sikaflex -291i. and purpose. Sika reserves the right to Advice on specific applications is change the properties of its products. available from the Technical Ser- The proprietary rights of third parties vice Department of Sika Industry. Further Information must be observed. All orders are ac- Copies of the following publications cepted subject to our current terms of Application sale and delivery. Users must always Cut off the tip of the nozzle to suit are available on request: - Material Safety Data Sheets refer to the most recent issue of the joint width and apply the sealant local Product Data Sheet for the prod- with a suitable hand operated or - Sika Pre-Treatment Chart for uct concerned, copies of which will be compressed-air gun, taking care to Marine Applications supplied on request. avoid air entrapment. - General Guidelines Bonding and ® Sealing with Sikaflex
PT. Sika Indonesia Branches
Jl. Raya Cibinong- Bekasi km. 20 Jl. KIG Raya Utara Kav. 3-4 Jl. Serbaguna (simp. Jl. Veteran) Limusnunggal- Cileungsi Kawasan Industri Gresik Kompleks Pergudangan Brayan Trade Center Bogor 16820 – Indonesia Gresik, Indonesia No. 34 Tel. +62 21 8230025 Tlp.+62 (031) 3951633 Medan, Sumatera Utara 20239 Fax +62 21 8230026 Fax +62 (031) 3951632 Tel. +62 61 8446697 Website : idn.sika.com +62 61 8446997 e-mail: sikacare@id.sika.com Fax +62 61 8446698