Академический Документы
Профессиональный Документы
Культура Документы
TECHNICAL MANUAL
FOR
RADIO FREQUENCY WATTMETER
H E A D Q U A R T E R S , D E P A R T M E N T O F T H E A R M Y
JULY 1977
*TM 11-6625-257-24P
REPORTING OF ERRORS
You can improve this manual by recommending improvements using DA Form 2028-2 (Test)
located in the back of the manual. Simply tear out the self-addressed form, fill it out as shown on
the sample, fold it where shown, and drop it in the mail.
If there are no blank DA Form 20282 (Test) in the back of your manual, use the standard DA
Form 2028 (Recommended changes to Publications and Blank Forms) and forward to the
Commander, US Army Electronics Command, ATTN: DRSEL-MA-Q, Fort Monmouth, NJ 07703.
In either case a reply will be furnished direct to you.
Table of Contents
Illus
Page Figure
Section I. Introduction ........................................................................................................ 1
II. Repair parts list ................................................................................................. 5
Group 00 Radio Frequency Wattmeters TS-118A/AP ....................................................... 5 1-2
01 Cable assemblies ............................................................................................. 9 3
Section III. Special tools list (Not applicable)
IV. National stock number and part number index ................................................. 10
*This manual supersedes TM 11-6625-257-20P, 15 August 1973 and TM 11-6625-257-34P, 15 August 1973.
i
TM 11-6625-257-24P
SECTION I
INTRODUCTION
1. Scope b. Source, Maintenance, and Recoverability
This manual lists spares and repair parts; special tools; (SMR) Codes.
special test, measurement, and diagnostic equipment
(TMDE), and other special support equipment required (1) Source code. Source codes indicate the
for performance of organizational, direct support, and manner of acquiring support items for maintenance,
general support maintenance of the TS-118A/AP. It repair, or overhaul of end items. Source codes are
authorizes the requisitioning and issue of spares and entered in the first and second positions of the Uniform
repair parts as indicated by the source and maintenance SMR Code format as follows:
codes.
Code Definition
2. General PA — Item procured and stocked for anticipated or
This Repair Parts and Special Tools List is divided into known usage.
the following sections:
XD — A support item that is not stocked. When
a. Section II. Repair Parts List. A list of spares required, item will be procured through normal
and repair parts authorized for use in the performance of supply channels.
maintenance. The list also includes parts which must be NOTE
removed for replacement of the authorized parts. Parts Cannibalization or salvage may be
lists are composed of functional groups in numeric used as a source of supply for any
sequence, with the parts in each group listed in figure items source coded above except
and item number sequence. those coded XA and aircraft support
items as restricted by AR 700-42.
b. Section III. Special Tools List. Not applicable.
(2) Maintenance code. Maintenance codes
c. Section IV. National Stock Number and Part are assigned to indicate the levels of maintenance
Number Index. A list, in National item identification authorized to USE and REPAIR support items. The
number (NIIN) sequence, of all National stock numbers maintenance codes are entered in the third and fourth
(NSN) appearing in the listings, followed by a list, in positions of the Uniform SMR Code format as follows:
alphameric sequence, of all part numbers appearing in
the listings. National stock numbers and part numbers (a) The maintenance code entered in the
are cross-referenced to each illustration figure and item third position will indicate the lowest maintenance level
number appearance. authorized to remove, replace, and use the support item.
The maintenance code entered in the third position will
3. Explanation of Columns indicate one of the following levels of maintenance:
a. Illustration. This column is divided as follows:
(1) Figure number. Indicates the figure Code Application /Explanation
number of the illustration on which the item is shown. O—Support item is removed, replaced, used at the
(2) Item number. The number used to organizational level.
identify item called out in the illustration. H—Support item is removed, replaced, used at the
general support level.
1
TM 116625-257-24P
(i.e., all authorized maintenance functions). This performing the actual maintenance function. This
position will contain one of the following maintenance measure is expressed by a two-character alphabetical
codes: abbreviation (e.g., ea, in, pr, etc). When the unit of
measure differs from the unit of issue, the lowest unit of
Code Application/Explanation issue that will satisfy the required units of measure will
H—The lowest maintenance level capable of complete be requisitioned.
repair of the support item is the general support
level. h. Quantity Incorporated in Unit. Indicates the
Z—Nonrepairable. No repair is authorized. quantity of the item used in the breakout shown on the
illustration figure, which is prepared for a functional
(3) Recoverability code. Recoverability codes group, subfunctional group, or an assembly.
are assigned to support items to indicate the disposition
action on unserviceable items. The recoverability code is 4. Special Information
entered in the fifth position of the Uniform SMR Code
format as follows: The following publications pertain to the TS-118A/AP and
its components:
Recoverability
Codes Definition TM 11-1036A, Radio Frequency Wattmeter TS-118A/AP
Z—Nonreparable item. When unserviceable, condemn
and dispose at the level indicated in position 3. 5. How to Locate Repair Parts
H—Reparable item. When uneconomically reparable,
condemn and dispose at the general support a. When National stock number or part number is
level. unknown.
c. National Stock Number. Indicates the National (1) First. Using the table of contents,
stock number assigned to the item and will be used for determine the functional group within which the item
requisitioning purposes. belongs. This is necessary since illustrations are
prepared for functional groups and listings are divided
d. Part Number. Indicates the primary number into the same groups.
used by the manufacturer (individual, company, firm,
corporation, or Government activity), in which controls (2) Second. Find the illustration covering the
the design and characteristics of the item by means of its functional group to which the item belongs.
engineering drawings, specifications, standards, and
inspection requirements to identify an item or range of (3) Third. Identify the item on the illustration
items. and note the illustration figure and item number of the
item.
NOTE
When a stock numbered item is (4) Fourth. Using the Repair Parts Listing,
requisitioned, the repair part received find the figure and item number noted on the illustration.
may have a different part number
than the part being replaced. b. When National stock number or part number is
known.
e. Federal Supply Code for Manufacturer
(FSCM). The FSCM is a 5-digit numeric code listed in (1) First. Using the Index of National Stock
SB 70842 which is used to identify the manufacturer, Numbers and Part Numbers, find the pertinent National
distributor, or Government agency, etc. stock number or part number. This index is in NIIN
sequence followed by a list of part numbers in
f. Description. Indicates the Federal item name alphameric sequence, cross-referenced to the illustration
and, if required, a minimum description to identify the figure number and item number.
item.
2
TM 11-6625-257-24P
3
TM 11-6625-257-24P
4
SECTION II TM 11-6625-257-24P
5
TM 11-6625-257-24P
6/(7 BLANK)
TM 11-6625-257-24P
8
SECTION II TM 11-6625-257-24P
9
SECTION IV NATIONAL STOCK NUMBER AND PART NUMBER INDEX TM 11-6625-257-24P
10
TM 11-6625-257-24P
BERNARD, W. ROGERS
General, United States Army
Official: Chief of Staff
PAUL T. SMITH
Major General, United States Army
The Adjutant General
Distribution:
To be distributed in accordance with DA Form 12-51, Direct and General Support Maintenance requirements for AN/FRC-
28, AN/GRC-10, AN/GRC-9, AN/GRC-40, AN/GRC-19, AN/TRC-22, AN/TRC-28, AN/FRC-28.
PIN: 032534
This fine document...
I am not asking you for donations, fees or handouts. If you can, please
provide a link to liberatedmanuals.com, so that free manuals come up first in
search engines:
– Sincerely
Igor Chudov
http://igor.chudov.com/
– Chicago Machinery Movers