Академический Документы
Профессиональный Документы
Культура Документы
PART –A
2. Why do we choose the Q point at the center of the load line? (2)
3. Name the two techniques used in the stability of the q point .explain.? (2)
4. Define stability factor &Give the expression for stability factor? (2)
16. Why the operating point is selected at the Centre of the active region? (2)
25. What are the advantages of double tuned over single tuned? (2)
PART –B
1. Draw the circuit of a common source FET amplifier & explain its operation? (16)
Obtain its AC equivalent circuit & drive the expression for voltage gain? (16)
of them. (16)
6. i) What is meant by bias stability? What factors affect BJT biasing? (8)
ii)With the help of neat diagram explain the voltage divider biasing method for JFET
(8)
ii) Draw the circuit diagram of self-bias circuit using CE configuration and explain
8. Draw the small signal hybrid model of CE amplifier and derive the expression for
its
UNIT II
PART –A
4. If the rise time of a BJT is 35 nano seconds, what is the bandwidth that can be
PART –B
1. Derive the expression for the CE short circuit current gain of transistor at high
frequency (16)
2. i)What is the effect of Cb’e on the input circuit of a BJT amplifier at High
frequencies? (8)
ii)Derive the equation for gm which gives the relation between gm, Ic and
temperature. (8)
4. i) Define fα,fβ and fT and state the relation between fβ and fT (8)
5. Define unity gain frequency. Obtain the necessary relation using transistor
frequency response. (16)
6. Using hybrid π model for CE amplifier. Derive an expression for its short circuit
UNIT III
UNTUNED AMPLIFIERS
PART A
PART –B
1. Describe in detail about the different types of distortions occur in amplifier?(16)
3. With the neat sketch describe the principle of operation of RC coupled amplifier?
(16)
4. Explain the operation of low frequency response CE amplifier and also discuss
5. Draw the equivalent circuit of cascaded CE stage and also derive an expression
UNIT IV
PART –A
1. What is feed back and what are feed back amplifiers? (2)
3. What are the advantages and disadvantages of negative feed back? (2)
8. Give the expression for the frequency of oscillations in an op-amp sine wave
oscillator? (2)
9. What are the conditions for sustained oscillator or what is Backhouse criterion?(2)
17. Give the topology of current amplifier with current shunt feedback? (2)
19. What is the minimum value of hfe for the oscillations in transistorized RC
PART –B
ii) Find the value of inductor in the Colpitts oscillator if c1=0.2μf, c2=0.02μf
And the frequency of the oscillator is 10 kHz. .Find the required gain for
Oscillator? (6)
ii) Determine the voltage gain, input and output amplifier with feedback for
Voltage series feedback having A =-100, Ri=10kΩ, Ro=20 kΩ and β= -0.1 (8)
6. With a neat circuit diagram explain the working of RC phase shift oscillator.
7. With a neat circuit diagram explain the working of Wien bridge phase shift
8. With the topologies compare the four types of negative feedback amplifier?(16)
9. Draw and explain the Colpitts oscillator circuit and determine the frequency of
oscillator? (16)
UNIT V
PART –A
2. Define conversion efficiency of a power amplifier. What is its value for class C
9. What is the advantage of using the output transformer for a class A amplifier? (2)
PART –B
2. Prove that the maximum efficiency of class B amplifier is 78.5%. and that of Class
A
3. Draw the circuit of push pull class B power amplifier coupled using transformers
and
explain the operation. Prove that all the even harmonics get eliminated. What is the
4. i) Compare class A, class B and class C power amplifier in their performance and
efficiency. (10)
5. What is the difference between a voltage amplifier and a power amplifier? (16)
amplifier? (16)
7. With the help of neat diagram. Explain the characteristics of class A amplifier and
also derive an expression for its efficiency and figure of merit. (16)