Академический Документы
Профессиональный Документы
Культура Документы
5
Company: Page: 1
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
Specifier's comments:
1 Input data
Anchor type and diameter: HIT-HY 200 + Rebar G30 10M
Effective embedment depth: hef,act = 226 mm (hef,limit = - mm)
Material: G30.18 Gr. 400
Evaluation Service Report: ESR-3187
Issued I Valid: -|-
Proof: Design method CSA A23.3-14 / Chem.
Stand-off installation: - (Recommended plate thickness: not calculated)
Profile:
Base material: cracked concrete, fc' = 17.24 N/mm2; h = 10,668 mm, Temp. short/long: 20/20 °C
Installation: hammer drilled hole, Installation condition: Dry, Installation direction: vertical downward
Reinforcement: tension: condition B, shear: condition B; no supplemental splitting reinforcement present
edge reinforcement: none or < 15M bar
R
- The anchor calculation is based on a rigid anchor plate assumption.
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.8.5
Company: Page: 2
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
3 Tension load
Load Nf [kN] Capacity Nr [kN] Utilization bN = Nf/Nr Status
Steel Strength* 34.000 32.130 106 not recommended
Bond Strength** 34.000 13.504 252 not recommended
Sustained Tension Load Bond Strength* N/A N/A N/A N/A
Concrete Breakout Strength** 34.000 8.098 420 not recommended
* anchor having the highest loading **anchor group (anchors in tension)
Variables
n Ase,N [mm2] futa [N/mm2]
1 100 540.00
Calculations
Ns,uta [kN]
54.000
Results
Ns,uta [kN] fs R Nsar [kN] Nfa [kN]
54.000 0.850 0.700 32.130 34.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.8.5
Company: Page: 3
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
Nar = (AA ) y
Na
Na0
ed,Na y cp,Na Nbar CSA A23.3-14 Eq. D.20
Nar ≥ Nfa CSA A23.3-14 Table D.1
ANa = see CSA A23.3-14, Part D.6.5.1, Fig. D.11
ANa0 = (2 cNa)2 CSA A23.3-14 Eq. D.22
cNa = 10 da √t uncr
7.60
CSA A23.3-14 Eq. D.23
( )
1
y ec,Na = e' ≤ 1.0 CSA A23.3-14 Eq. D.25
1+ N
cNa
y ed,Na = 0.7 + 0.3 ( )
ca,min
cNa
≤ 1.0 CSA A23.3-14 Eq. D.27
y cp,Na = MAX ( )
ca,min cNa
,
cac cac
≤ 1.0 CSA A23.3-14 Eq. D.29
Nbar = l a f c t r p da hef R CSA A23.3-14 Eq. D.24
Variables
2 2
t uncr [N/mm ] da [mm] hef [mm] ca,min [mm] aoverhead t cr [N/mm ]
10.80 11 226 57 1.000 7.40
e'1,N [mm] e'2,N [mm] cac [mm] la
0 0 357 1.000
Calculations
cNa [mm] ANa [mm2] ANa0 [mm2] y ed,Na
135 30,713 72,582 0.827
y ec1,Na y ec2,Na y cp,Na
1.000 1.000 1.000
Results
fc R Nbar [kN] Nar [kN] Nfa [kN]
0.650 1.000 38.591 13.504 34.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.8.5
Company: Page: 4
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
Ncbr = (AA ) y
Nc
Nc0
ed,N y c,N y cp,N Nbr CSA A23.3-14 Eq. D.3
Ncbr ≥ Nfa CSA A23.3-14 Table D.1
ANc see CSA A23.3-14, Part D.6.2.1, Fig. D.7
ANc0 = 9 h2ef CSA A23.3-14 Eq. D.5
( )
1
y ec,N = 2 e'N ≤ 1.0 CSA A23.3-14 Eq. D.8
1+
3 hef
y ed,N = 0.7 + 0.3 ( ca,min
1.5hef )
≤ 1.0 CSA A23.3-14 Eq. D.11
y cp,N = MAX (
ca,min 1.5hef
cac
,
cac )
≤ 1.0 CSA A23.3-14 Eq. D.13
1.5
Nbr = kc f c l a √fc hef R
'
CSA A23.3-14 Eq. D.6
Variables
hef [mm] e'1,N [mm] e'2,N [mm] ca,min [mm] y c,N
226 0 0 57 1.000
Calculations
ANc [mm2] ANc0 [mm2] y ec1,N y ec2,N y ed,N y cp,N
77,292 459,684 1.000 1.000 0.750 1.000
Results
fc R Nbr [kN] Ncbr [kN] Nfa [kN]
0.650 1.000 64.181 8.098 34.000
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.8.5
Company: Page: 5
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
4 Shear load
Load Vf [kN] Capacity Vr [kN] Utilization bV = Vf/Vr Status
Steel Strength* N/A N/A N/A N/A
Steel failure (with lever arm)* N/A N/A N/A N/A
Pryout Strength (Bond Strength controls)* N/A N/A N/A N/A
Concrete edge failure in direction ** N/A N/A N/A N/A
* anchor having the highest loading **anchor group (relevant anchors)
5 Warnings
• The anchor design methods in PROFIS Anchor require rigid anchor plates per current regulations (ETAG 001/Annex C, EOTA TR029, etc.). This
means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor plate is assumed to be
sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Anchor calculates the minimum required anchor plate
thickness with FEM to limit the stress of the anchor plate based on the assumptions explained above. The proof if the rigid anchor plate
assumption is valid is not carried out by PROFIS Anchor. Input data and results must be checked for agreement with the existing conditions and
for plausibility!
• Condition A applies when supplementary reinforcement is used. The R factor is increased for non-steel Design Strengths except Pullout Strength
and Pryout strength. Condition B applies when supplementary reinforcement is not used and for Pullout Strength and Pryout Strength. Refer to
your local standard.
• Checking the transfer of loads into the base material is required in accordance with CSA A23.3!
• Installation of Hilti adhesive anchor systems shall be performed by personnel trained to install Hilti adhesive anchors. CSA A23.3-14 Annex D,
Clause D.10.1
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
www.hilti.ca Profis Anchor 2.8.5
Company: Page: 6
Specifier: Project:
Address: Sub-Project I Pos. No.:
Phone I Fax: | Date: 2019-10-30
E-Mail:
6 Installation data
Anchor plate, steel: - Anchor type and diameter: HIT-HY 200 + Rebar G30 10M
Profile: - Installation torque: -
Hole diameter in the fixture: - Hole diameter in the base material: 14 mm
Plate thickness (input): - Hole depth in the base material: 226 mm
Recommended plate thickness: - Minimum thickness of the base material: 256 mm
Drilling method: Hammer drilled
Cleaning: Compressed air cleaning of the drilled hole according to
instructions for use is required
Input data and results must be checked for agreement with the existing conditions and for plausibility!
PROFIS Anchor ( c ) 2003-2009 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan