Академический Документы
Профессиональный Документы
Культура Документы
EIC-E-1003-0
■ Solenoid Controlled Pilot Operated Directional Valves
These valves are composed of a solenoid operated pilot valves and a pilot operated slave valve. When a solenoid is
energised the pilot valve directs the flow to move the spool of the slave valve, thus changing the direction of flow in
the hydraulic circuit.
■ Specifications
Max.
*1
Max. Min. *2 Max. T-Line Back Changeover
Max. Pilot Pressure Kgf/cm2 Frequency
Valve Max. Operating Required Mass
Model Numbers Pressure Cycles/min
Type Flow Pressure Pilot Pres. Kg
2 Kgf/cm2
L/min Kgf/cm Kgf/cm2
Ext. Drain Int. Drain AC DC R
(S)-DSHG-04-3C※-※-50 8.8
(S)-DSHG-04-2N※-※-50 300 315 250 8 210 160 120 120 120 8.8
(S)-DSHG-04-2B※-※-50 8.2
(S)-DSHG-06-3C※-※-51
Standard 12.7
Type
(S)-DSHG-06-2N※-※-51 250 8 120 120 120 12.7
500 315 210 160
(S)-DSHG-06-2B※-※-51 12.1
(S)-DSHG-06-3H※-※-51 210 10 110 110 110 13.5
(S)-DSHG-10-3C※-※-41
Shockless
Type 120 120 100 45.3
250
(S)-DSHG-10-2N※-※-41 100 100 100 45.3
1100 315 10 210 160
(S)-DSHG-10-2B※-※-41 44.7
210 60 60 50
(S)-DSHG-10-3H※-※-41 53.1
* 1. Maximum flow indicates a ceiling flow. As the ceiling flow
depends on the type of spool and operating condition, refer to the
list of Spool Functions on pages 375 to 377 for details.
* 2. Pilot pressure of internal pilot drain models must always exceed
tank line back pressure by a minimum required pilot pressure.
Drain Connection
Type of Electrical
Number of Valve
Pilot Connection
Design Number
Series Number
Position Valve
Spool-Spring
Spool Control
Special Two
Arrangement
Modification
Choke Valve
Special Seals
Conduit Con.
Spool Type
Valve Size
Offset Sol.
Coil Type
Positions
Type
2,4,
40,60,
C:
10,12
3 Spring --- ---
(3,5, R2:
Centred C1: *
6,*17, With
With C1
9,11) Stroke None:
None: With AC
2,4, Adjust- Terminal
Stan- A *2 Choke None: A100,
04 N: 40,6, None: ment, Box 50
dard (Omit if Inter- A120
No- 60,9, Exter- Both Type
Type not nal A200, L:
Spring 12 nal Ends
Required) C2: * Pilot A240
2 (3,7) *1 Drain N: (Omit
With C2 if not
DSH: 2,4, A *2 B *2 With Plug-in
F: Solenoid B: RA: Con- Required)
40,60, (Omit Choke
For Con- G: Spring With nector
10,12 if not
Phos- trolled Sub- Offset Stroke Type
(3,7) *1 Required) DC
phate Pilot plate Adjust-
2,4, D12,
Ester Operated Mount ment
40,60, C1C2: * D24
Type Direc- -ing C: Port”A”
10,12 With D100
Fluids tional 3 Spring --- End N1: 51
(3,5, C1&C2
Valve. Centred Plug-in
6 *17, Choke
S:
Shock-
06
N:
9,11)
2,4,
A *2
(Omit
E:
Exter-
nal
T:
Inter-
nal
RB:
With
AC→DC
Con-
*3 nector
with
---
E
(Omit Drain Stroke indica-
less if not Pilot R110,
■ Solenoid Ratings
Solenoid ratings of pilot valve are identical with those of standard
solenoid valve. Refer to relevant solenoid ratings described on the page below.
Pilot Valve Model Solenoid Rating described on
Model Numbers
Numbers The page below
(S-)DSHG-04
(S-)DSHG-06 DSG-01- ※※※-※-50 EIC-E-1001
Page No.349
(S-)DSHG-10
■ Sub-plates
Valve
Sub-plate Model Thread Approx.
Model
Numbers Size Mass Kg
Numbers
DHGM-04-2080 1/2 BSP.F 4.4
DSHG-04
DHGM-04X-2080 3/4 BSP.F 4.1
DHGM-06-5080 3/4 BSP.F
DSHG-06 8.5
DHGM-06X-5080 1 BSP.F
DHGM-10-4080 1-1/4 BSP.F
DSHG-10 21.5
DHGM-10X-4080 1-1/2 BSP.F
Sub-plates are available. Specify sub-plate model from the table above. When Sub-plates are not used, the
mounting surface should have a good machined finish.
■ Mounting Bolts
Mounting Bolt
Model Numbers Name Mounting Bolt Qty.
Ordering Code
M6 x 45 Lg. 2
DSHG-04 Soc. Hd. Cap. Screw BKDSHG-04-50
M10 x 50 Lg. 4
DSHG-06 Soc. Hd. Cap. Screw M12 x 60 Lg. 6 BKDSHG-06-51
DSHG-10 Soc. Hd. Cap. Screw M20 x 75 Lg. 6 BKDSHG-10-41
■ Options
Models with Pilot Choke Adjustment Models with Pilot Stroke Adjustment
(C1/C2/C1C2) (R2/RA/RB)
“C1” Models --- By turning the adjusting screw When the adjusting screw is screwed in, the
clockwise, main spool changeover main spool stroke becomes short and flow rate
speed by the pilot pressure can be reduces.
lowered. But centering speed of Graphic symbols (Ex. Spring Centered)
spring centered modes can not be “R2” Models
changed.
AB
a b
“C2” Models --- When the adjusting screw is turned
clockwise, main spool changeover Y PT
speed can be lowered and centering
speed of spring centered models “RA” Models
can be also lowered.
AB
a b
Y PT
Graphic symbols (Ex. Spring Centered)
“RB” Models
C2 Choke AB
a b
a b
C1 Choke Y PT
DSHG-04-3C60
"60" 300 300 300 300
"7"
S-DSHG-04-3C60
Two Positions
No-Spring Spring Offset
Graphic Symbol Maximum Flow Graphic Symbol Maximum Flow
Spool Type A B L/min. A B L/min.
a b b
100 160 250 315 100 160 250 315
Y P T
Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm² Y P T
Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm²
"2" (S-)DSHG-04-2N2 300 300 300 300 (S-)DSHG-04-2B2 300 300 300 300
"3" DSHG-04-2N3 300 300 300 300 DSHG-04-2B3 300 300 300 300
"4" (S-)DSHG-04-2N4 300 300 300 300 (S-)DSHG-04-2B4 300 300 300 300
"40" (S-)DSHG-04-2N40 300 300 300 300 (S-)DSHG-04-2B40 300 300 300 300
"7" DSHG-04-2N7 300 300 300 300 DSHG-04-2B7 300 300 300 300
Note:
1 Max. Flow described above shows value at pilot pressure more than 6 Kgf/cm2. A B
2 Max. Flow shows value at the condition of the flow as shown in right figure a b
P→A→B→T (or P→B→A→T). P T
Max. Flow differs according to hydraulic circuit, if port “A” or “B” is blocked.
Consult Yuken for such application.
3 For values in the double row, upper is maximum flow at pilot pressure 5Kgf/cm2.
(In case pressure centered model, pilot pressure is 5 Kgf/cm2),
lower is pilot pressure of 7 Kgf/cm2.
"3" DSHG-06-3C3 500 500 460 370 DSHG-06-3H3 500 500 500 500
"7" DSHG-06-3C7 500 500 450 360 DSHG-06-3H7 500 500 500 500
450 360
"9" DSHG-06-3C9 500 500 DSHG-06-3H9 500 500 500 500
500 500
410 310 460
"10" (S-)DSHG-06-3C10 500 500 (S-)DSHG-06-3H10 500 500 500
500 500 500
410 310 460
"11" DSHG-06-3C11 500 500 DSHG-06-3H11 500 500 500
500 500 500
410 310 460
"12" (S-)DSHG-06-3C12 500 500 (S-)DSHG-06-3H12 500 500 500
500 500 500
Two Positions
No-Spring Spring Offset
Graphic Symbol Maximum Flow Graphic Symbol Maximum Flow
Spool Type L/min L/min
A B A B
a b
100 160 250 315 b
100 160 250 315
Y P T Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm² Y P T Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm²
"2" (S-)DSHG-06-2N2 500 500 500 500 (S-)DSHG-06-2B2 500 500 500 500
"3" DSHG-06-2N3 500 500 500 500 DSHG-06-2B3 500 500 500 500
"4" (S-)DSHG-06-2N4 500 500 500 500 (S-)DSHG-06-2B4 500 500 500 500
"40" (S-)DSHG-06-2N40 500 500 500 500 (S-)DSHG-06-2B40 500 500 500 500
"7" DSHG-06-2N7 500 500 500 500 DSHG-06-2B7 500 500 500 500
1040
1100
Two Positions
No-Spring Spring Offset
Graphic Symbol Maximum Flow Graphic Symbol Maximum Flow
Spool Type L/min L/min
A B A B
a b
100 160 250 315 b
100 160 250 315
Y P T Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm² Y P T Kgf/cm² Kgf/cm² Kgf/cm² Kgf/cm²
"2" (S-)DSHG-10-2N2 1100 1100 1100 1100 (S-)DSHG-10-2B2 1100 1100 1100 1100
"3" DSHG-10-2N3 1100 1100 1100 1100 DSHG-10-2B3 1100 1100 1100 1100
"4" (S-)DSHG-10-2N4 1100 1100 1100 1100 (S-)DSHG-10-2B4 1100 1100 1100 1100
"40" (S-)DSHG-10-2N40 1100 1100 1100 1100 (S-)DSHG-10-2B40 1100 1100 1100 1100
"7" DSHG-10-2N7 1100 1100 1100 1100 DSHG-10-2B7 1100 1100 1100 1100
Note :
1 Relation between max. flow and pilot pressure is
Value in the single column is constant regardless of pilot pressure subject to pilot A B
pressure more than 10 Kgf/cm2. a b
2 P T
For values in the double row, upper is max. flow at pilot pressure 10 Kgf/cm . Lower is
pilot pressure of 15 Kgf/cm2.
2 Max. Flow shows value at the condition of the flow as shown in right figure
P→A→B→T (or P→B→A→T).
Max. Flow differs according to hydraulic circuit, if port “A” or “B” is Blocked,
consult Yuken for such application.
A B A B
b a
Y P T P T Y
Standard Offset Alternate Offset (“L”)
■ Valve with Centre Position and One Offset Position (Special Two Position Valve)
In addition to the standard two position valves as shown in the table on pages 375 to 377 two kinds of
valves are available with center position and either one of two offset positions.
Standard and alternate offset types use solenoid “b” and solenoid “a” respectively.
(Example) In case of spool Type “2”
Center Position
Sol. a energised Sol. b energised
A B
a b
Y P T
A B A B
b b
Y P T Y P T
"A" : (2B2A) "B" : (2B2B)
Model Numbers Standard Alternate Model Numbers Standard Alternate Model Numbers Standard
Offset Offset Offset Offset
Offset Type
Type Type Type Type
Y P T P T Y Y P T P T Y Y P T
10 10 10
■ Pressure Drop
Pressure drop curves based on viscosity of 35cSt and specify gravity of 0.850.
DSHG-04, S-DSHG-04
Kgf/cm² 1 2
Spool Pressure Drop Curve Numbers Spool Pressure Drop Curve Numbers
3 Type P→A B→T P→B A→T P→T Type P→A B→T P→B A→T P→T
12 4
2 5 (2) 4 (2) 5 (2) 6 (4) − 60 7 5 7 7 2
∆P
5
10 3 5 3 5 5 7 7 5 4 5 6 −
6
4 5 (2) 3 (3) 5 (2) 5 (5) − 9 5 4 5 6 −
Pressure Drop
8 7
40 5 (2) 4 (4) 5 (2) 6 (6) − 10 5 (2) 2 (2) 5 (2) 6 (4) −
6 5 7 4 5 5 5 11 6 4 5 6 −
6 5 (6) 3 (4) 5 (6) 6 (7) 1 (2) 12 5 (2) 4 (2) 5 (2) 5 (5) −
4
DSHG-06, S-DSHG-06
1
Kgf/cm² 2
20 3
E
∆P
4
16
12 6 Spool Pressure Drop Curve N umbers Spool Pressure D rop Curve Numbers
Type P→ A B→ T P→ B A→ T P→ T Type P→ A B→ T P→ B A → T P→ T
7
8
2 8 (6) 5 (1) 8 (6) 7 (2) − 60 5 (6) 5 (2) 6 (6) 7 ( 3) 3 ( 1)
8
3 6 4 6 7 6 7 6 4 6 7 −
4
4 8 (6) 5 (2) 8 (6) 7 (2) − 9 6 5 6 7 −
0 40 8 5 8 7 − 10 8 5 8 7 −
0 100 200 300 400 500 L/min 5 8 4 5 7 2 11 8 4 5 7 −
Flow Rate 6 5 1 5 4 3 12 8 5 8 7 −
DSHG-10, S-DSHG-10
1
Kgf/cm²
2
20 3 Spool Pressure Drop Curve Numbers Spool Pressure Drop Curve Numbers
∆P
4 Type P→A B→T P→B A→T P→T Type P→A B→T P→B A→T P→T
16 5 2 9 ( 8) 6 ( 3) 9 ( 8) 8 ( 4) − 60 8 ( 8 ) 5 ( 4 ) 8 ( 8 ) 5 ( 4 ) 3 ( 2 )
Pressure Drop
12 6 3 7 6 7 7 5 7 7 6 7 7 −
7 4 9 ( 8) 6 ( 5) 9 ( 8) 6 ( 6) − 9 7 6 7 7 −
8 8 40 9 6 9 8 − 10 9 5 9 8 −
5 9 6 8 6 1 11 9 6 8 7 −
4 9
6 5 3 5 4 2 12 9 7 9 6 −
0
0 200 400 600 800 1000 1100 L/min
Flow Rate
P' = P (G'/0.850)
Changeover Time
SOL "ON" : 3C SOL "ON" : 3C
SOL "OFF" : 3C SOL "OFF" : 3C
100 100
SOL "ON" : 2B
2N SOL "ON" : 2B
50 SOL "OFF" : 2B 50 SOL "OFF" : 2B
0 50 100 150 200 250 Kgf/cm² 0 50 100 150 200 250 Kgf/cm²
Pilot Pressure Pilot Pressure
DSHG-10
ms
250
Changeover Time
200
SOL "OFF" : 3C
150
SOL "ON" : 3C
2N SOL "ON" &
100 SOL "OFF" : 2B
50
DIMENSIONS IN
204 Pressure Port "P"
11 Dia. x Thru. MILLIMETRES
101.6 50.4 Pilot Pressure Port "X"
17.5 Dia. Spotface
4 Places 34 (For External Pilot Models only)
UKEN
Pilot Drain Port "Y"
(For External Drain Models Only)
69.8
72.9
91
34.9
Cylinder Port "A" 7 Dia. x Thru. Cylinder Port "B" EIC-E-1001 Page 357.
11 Dia. Spotface Cable Departure*
2 Places Cable Applicable:
210 Outside Dia. ------ 8-10mm
Conductor Area --- Not Exceeding 1.5mm²
97 56.5
27
39
64 Max.
Manual Actuator
192 Max.
Nut 22 Hex.
116
3 Dia.
35
181.3
Nut 27 Hex.
163
116
32
53.4
Mounting Surface Locating Pins
4
(O-Ring Furnished) 2 Places
Dimensions mm
118 Max.
Model Numbers
92.1
C D E F
※※※-A※-N/N1 39 53 202 27.5
46.1
(S-)DSHG-06-
(S-)DSHG-06-※※※-D※-N/N1 39 64 213 27.5
156
Cylinder Port "B"
Pilot Pressure Port "X"
(For External Pilot Models Only) Cylinder Port "A" Cable Departure
Cable Applicable :
Outside Dia. --- 8-10 mm
210
Conductor Area --- Not Exceeding 1.5 mm²
56.5
97 C
F
D
Nut 22 Hex.
E
137
41
(O-Ring Furnished)
Position of cable departure can be changed. For details, refer to DSG-01 valve on EIC-E-1001 Page 357.
Solenoid Controlled Pilot Operated Directional Valves
381
DIRECTIONAL CONTROLS
■ Terminal Box Type : (S-)DSHG-06- - -41
210 52
90 60 Space Needed to Remove 48
Solenoid-Each End
Electrical conduit
Manual
connection "C" Thd.
Actuator 6
(Both Ends)
Sol a Sol b
Dia. x Thru.
202.3
Nut 22
184
137
41
6
51.3
Mounting surface 6 Dia. Locating Pins
(O-Ring furnished) 2 Places
Dimensions mm
43
Model Numbers
158.8
C D E F
※※※-A※-N/N1
43
233.8
Cylinder Port "A" Cylinder Port "B"
Pilot Pressure Port "X"
(For External Pilot Model) Cable Departure
Cable Applicable :
105 Outside Dia. --- 8-10 mm
56.5 Conductor Area --- Not Exceeding 1.5 mm²
97 C F
D
E
200
45
(O-Ring Furnished)
Position of cable departure can be changed. For details, refer to DSG-01 valve on EIC-E-1001 Page 357.
Solenoid Controlled Pilot Operated Directional Valves
382
DIRECTIONAL CONTROLS
210 52
90 60 Space Needed to Remove
Solenoid-Each End 48
Electrical conduit
connection
Manual "C" Thd.
Actuator 6 (Both Ends)
M8 Thd.
Two Eye Dia. x Thru.
Bolts Nut 22
265.3
247
200
6 45
28.5
Mounting surface 6 Dia. Locating Pins
(O-Ring furnished) 2 Places
DIMENSIONS IN
MILLIMETRES E
OPTIONS Models with Pilot Choke valve
SOL a SOL b
LOCK
J
LOCK
E
F
H
Dimension mm
Model Numbers J
E F H
AC SOL DC SOL R SOL
(S-)DSHG-04-※※※-C1 145 -- 100 220 220 220
(S-)DSHG-04-※※※-C2 145 100 -- 220 220 220
(S-)DSHG-04-※※※-C1C2 185 140 100 260 260 260
(S-)DSHG-06-※※※-C1 177 -- 132 252 252 252
(S-)DSHG-06-※※※-C2 177 132 -- 252 252 252
(S-)DSHG-06-※※※-C1C2 217 172 132 292 292 292
(S-)DSHG-10-※※※-C1 240 -- 195 390 401 404
(S-)DSHG-10-※※※-C2 240 195 -- 315 315 315
(S-)DSHG-10-※※※-C1C2 280 235 195 355 355 355
SOL a SOL b
E
Fully Extended D
Stroke Adjustment Screw (Port "B" End )
Model Numbers C D E 13 Hex.
(S-)DSHG-04-※※※-R2 288 94 33
(S-)DSHG-06-※※※-R2 376 111 40
(S-)DSHG-10-※※※-R2 558 164.5 65
DIMENSIONS IN
MILLIMETRES
04
Sub Plate DHGM- -2080 Sub-plate
04X “C” Thd.
Model Numbers
DHGM-04-2080 1/2 BSP.F
DHGM-04X-2080 3/4 BSP.F
190
12 166
32.2 101.6 M10 Thd. x 21 Deep
76.7 4 Places 125
"C" Thd.
34 36 1 4 BSP.F Thd. 90
4 Places
18.3 20 2 Places 46
13.1
12
1.6
10.1
21.5
16
P
29
33
T
X
65
57.1
55.6
76
T
69.8
P
71.4
X
120
90
96
14.2
B Y Y B
A
A
11 Dia. x Thru. 50 58
6 Dia. 2 Places
17.5 Dia. Spotface 14.2 65.8 102
4 Places 17.5 Dia.
88.1 4 Places 137.5
130
3.6 Dia. x 5 Deep
2 Places M6 Thd. x 15 Deep
2 Places
06
DHGM- -5080
06X
1/4 BSP.F Thd. D
E
M12 Thd. x 24 Deep 4 Places F
204
12 180 6 Places 50 H
25 130.2 35 J
Y P T
Y
T W
92.1
P V
134
110
116
V
17.5
74.6
73.1
A W B A
11.9
X
46.1
B X
19.1
8.9
12.5 11 Dia. N
12
156 4 Places L
7 Dia. x 8 Deep "C" Thd.
24.5 Dia. 4 Places K
2 Places
4 Places
Sub-plate Dimensions mm
“C” Thd.
Model Numbers D E F H J K L N
DHGM-06-5080
DHGM-06X-5080
¾ BSP.F
1 BSP.F
151.2
155.2
137.7
148
102
106
54.4
50
30.6
25
125.8
130
78.2
74
42.5
32
E
※
DIMENSIONS IN
MILLIMETRES
10
DHGM- -4080
10X
306.5
20 266.5 7 Dia. x 8 Deep
2 Places
38 190.5
168.3 M20 Thd. x 34 Deep
147.6 6 Places
114.3 213
76.2 60 F
41.3 45 H "C" Thd.
4 Places
Y
Y P T
V
158.8
T P W
199
V
123.8
114.3
A B B A
79.4
X W
28.6
4 Places
Valve Types Pilot Pres. Port “X” Port “Y” Port “V” Port “W”
Used only on Used as drain port only
Solenoid
external pilot type on external drain type
Controlled
valves. valves.
Pilot Spring centered, No-spring,
Not used (plug is not required)
Operated Spring offset
To be plugged on To be plugged on *
Directional
internal pilot type internal pilot type
Valves
valves. valves.
Pilot Spring centered, No-spring, Used as pilot pres. Port
Operated
Used Not used (plug is not required)
Directional
Valves Spring offset Used pilot port drain port
Not used (plug
Not used Not used
Manually Operated Directional Valves Used is
(plug is not required) (plug is not required)
not required)
* As the thread is provided on the body, plug either port on the sub-plate or port on the body.
1/16-27 NPT
Removed For T P
T P
Internal Pilot
Models
1/16-27 NPT A B
T P
Removed for
Removed For Internal Pilot Models Internal
Drain Models
(S-)DSHG-06- - -51
(S-)DSHG-10- - -41
Removed for
Removed for Internal
Internal Drain Models
Pilot Models
Removed for
External
Drain Models