Академический Документы
Профессиональный Документы
Культура Документы
Safety Precaution
WARNING
Service should not be attempted by anyone unfamiliar with the necessary precautions on this
monitor.
The followings are the necessary precautions to be observed before servicing.
1. When managing this monitor , cover with shield plate to avoid to scrach on LCD surface.
2. When replacing a chassis in the cabinet, always be certain that all the protective devices are
put back in place, such as nonmetallic control knobs, insulating covers, shields, isolation
resistor capacitor network etc.
3. Before returning the monitor to the customer, always perform an AC leakage current check
on the exposed metallic parts of the cabinet, such as signal connectors, terminals, screw
heads, metal overlays, control shafts etc, to be sure the monitor is safe to operate without
danger of electrical shock.
General Information
1. Description
This 17" LCD color display monitor is operated in R, G, B drive mode input.
2. Operating instructions
2-1. Front
Power Switch , Menu, Select, Down, Up, DPMS (Power) LED
2-2. Rear
Input connector (AC & Signal Cable)
2-3. OSD Controls
H/V Position, Clock Phase, Brightness, Contrast, Recall, Color Control, Language, Auto
Adjust, Miscellaneous, Audio control, Auto Color
3. Electrical Characteristic
3-1. Power Supply
AC/DC - Input Voltage : 90V~264V
Input Current : 1.0 A Max
Input Ferquency : 50 ~ 60Hz
- Output Voltage 12V/5V
Output Current 2A/1.5A
3-2. Video Input Signal
Level : 0.7 Vp-p analog signal(at 75 ohm termination to ground)
Polarity : Positive
3-3. Horizontal Synchronization Signal
Level : TTL High : 2.4V min
Low : 0.4V max
Polarity : - or +
Frequency : 31kHz ~ 80kHz
3-4. Vertical Synchronization Signal
Level : TTL High : 2.4V min
Low : 0.4V max
Polarity : - or +
Frequency : 56Hz ~ 75Hz
--1--
Control Description
Front View
Support Modes
H Frequency V Frequency H V Dot Clock
NO Resolution (Hz)
(kHz) Polarity Polarity (MHz)
1 720 x 400 31.5 70.1 0 1 28.322
2 640 x 480 31.5 59.9 0 0 25.175
3 640 x 480 37.5 75.0 0 0 31.500
4 800 x 600 37.9 60.3 1 1 40.000
5 800 x 600 46.9 75.0 1 1 49.500
6 1024 x 768 48.4 60.0 0 0 65.000
7 1024 x 768 56.5 70.1 0 0 75.000
8 1024 x 768 60.0 75.0 1 1 78.750
9 1280 x 1024 63.900 60.000 1 1 108.00
10 1280 x 1024 79.976 75.025 1 1 135.00
--2--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
255
700mV
254
4
3
2
1
0 0mV
• H-Sync • V-Sync
--3--
Video Input Terminal
A 15 Pin D-sub connector is used as the input signal connector
Pin and input signals are shown in the table below.
Pin Description
1 RED
2 GREEN
3 BLUE
4 GND
5 RETURN
6 RED GROUND
7 GREEN GROUND
8 BLUE GROUND
9 N.C
10 LOGIC GROUND
11 GROUND
12 SDA
13 H-SYNC(TTL)
14 V-SYNC(VCLK)
15 SCL
--4--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
LINE OUT
--5--
Theory of Operation
1. AC/DC INVERTER
Input voltage : DC 12V
Input current : 2.0A(Max)
Output current : 6.5mArms(TYP)
Frequency(switching) : 47KHz(Max)
Output power : 18W(TYP)
On/off control voltage : 5.0V
2. AC/DC ADATOR
This display device shall maintain the specified per formances in the range de scribed
below
Frequency : 50/60Hz
Voltage : 90 - 264Vac RMS
The following consumption requirments shall be met:
Power Consumption : 35W(typ)
Current consumption : < 1.0 Aac RMS
Output Specification:
output1 : 12V/2A
output2 : 5V/1.5A
3. Audio System
This monitor has a audio system including two micro loudspeakers.
Each of two micro loudspeakers has a 2W(Max) output power.
This system also supports a headphone(earphone) output.
- Auto Signal Input : < 600mVp-p(Max.)
- Auto Amplifiers
2W+2W Amplifier with DC Volume Control (for two micro loudspeakers)
RL=8 @THD=10% Vcc=14V (min. 10V, max. 18V)
Dual-Audio Power Amplifier (for a headphone output)
RL=32 @THD=10% Vcc=4.5V (min. 1.8V, max. 15V)
- Speaker
Micro Loudspeaker Spec.
Normal impedance 8 15% at 1.0V 1.5KHz
Resonance Freq. 550Hz +/- 110Hz at 1.0V
Freq. Range fo ~ 20KHz
Power Rating Normal 1.0W/Peak 2.0W
4. DPMS MODE
Signal Power Recovery LED
Status
H-Sync V-Sync Video Consumption Time Indicator
--6--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
1280x1024
H:63.9 V:60.0
V:60.0
BRIGHTNESS
BRIGHTNESS
Adjust the brightness of the screen.
CONTRAST
Adjust the contrast of the screen.
COLOR CONTROL
Color temperature affects the tint of the image. With lower color
temperatures the image turns reddish and with higher temperatures
bluish.
There are three color settings available: Bluish, Reddish or USER. With
the USER setting you can set individual values for red, green and blue.
POSITION
H POSITION
Adjusts the horizontal position of the entire screen image.
V POSITION
Adjusts the vertical position of the entire screen image.
--7--
CLOCK PHASE
PHASE
Adjust the noise of the screen image.
CLOCK
Adjust the horizontal size of the entire screen image.
MISCELLANEOUS
RECALL
Recall the saved color data.
OSD TIMER
You can set the displayed time of OSD Menu window on the screen by using this
adjustment.
OSD POSITION
Adjust the OSD menu's horizontal or vertical position on the screen.
AUTO COLOR
Optimum color setting is auto programmed for user’s convenience.
LANGUAGE
You can select the language in which adjustment menus are displayed.
The following languages are available : English, French, German, Italian,
Spanish, Swedish, Finnish, Danish, Portuguese, Dutch and Japanese or chinese.
AUDIO
VOLUME
Adjust the audio volume level.
AUDIO
This menu is used to choose audio on or off.
AUTO ADJUST
You can adjust the shape of screen automatically at the full screen pattern.
--8--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
Step 1. At first Display, a full screen, such as, Window's background or "H" character should
be achieved by using Editor (ex: Notepad. exe)
Step 2. Adjust the screen to the center of the Display(LCD), by using the top and bottom
display controls. (i.e.Using V-Position Adjust menu)
Step 3. Adjust the screen to the center of the Display(LCD), by using the right and left
display controls. (i.e.Using Clock and H-Position adjust menu)
Step 4. Adjust the Clock-phase until the "H" Character displays clear.
Step 5. Using the Contrast. Brightness, and Color Control menu, set the color to your
preference.
Step 6. When you finish the adjustment, you can save your settings by pressing on the menu
until the OSD screen has disappeared.
Factory Setting & EEPROM Initialization Method
Factory Setting Method
- Connect the signal cable and power cable to the LCD monitor.
- Press Power switch with pressed MENU key.(Menu key + Power key).
- Then, a User can change the factory setting value in OSD menu.
- Save changed value and Turn off the power s/w.
- Turn on the power, adjust the screen.
--9--
Specification
SIZE 17” Viewable diagonal
Dot Pitch 0.264mm
LCD Module
Brightness 300 cd/m2 (TYP)
Response Time 12m-sec (Typ)/8m-sec (Typ)
Operating 5 to 35 °C
Temperature
Storage - 5 to 45 °C
Operating 30 to 80%(Non-condensing)
Humidity
Storage 5 to 90%(Non-condensing)
unpacked 3.8Kg
Weight
packed 5.0Kg
--10--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
--11--
Critcal Parts Specification
1. LCD Module
LTM170EU-L11, HT17E13-100, HSD170ME13-A4, LTM170EU-L21 is
a A-SI TFT active martix color liquid crystal compising amorphous
silicon TFT attached to each signal elecrode, a driving circuit and a
backlight. a built-in backlight display area contains 1280x1024
pixels and can display full color (16.2M/16.7M colors)
Model L70S+/L70S+(Lift Stand) L72S, L72S(Lift Stand)
Signal system Digital RGB signals, Sync Digital RGB signals, Sync
Backlight Edge light Four colt cathode flurescrnt Four colt cathode flurescrnt
HT17E13-100(BoeHydis)
HSD170ME13-A4(haunstar)
--12--
L70S+/L70S+(Lift Stand),L72S/L72S(Lift Stand) Technical Service Manual
2) CONNECTIONS
Physical interface is described as for the connector on module.
These connectors are capable of accommodating the following signals and will be following
components
Manufacturer JST
3) Signal Pin
--13--
4) Signal Description
The module using a pair of LVDS receiver SN75LVDS82 (Texas Instruments) or compatible.
LVDS is a differential signal technology for LCD interface and high speed data transfer
device. Transmitter shall be SN75LVDS83(negative edge sampling)or compatible. The first
LVDS port(RxOxxx)transmots odd pixels while the second LVDS port(RxExxxx)transmits
even pixels.
PIN # SIGNAL NAME DESCRIPTION
1 RxO0- Negative LVDS differential data input (odd data)
2 RxO0+ Positive LVDS differential data input (odd data)
3 RxO1- Negative LVDS differential data input (odd data)
4 RxO1+ Positive LVDS differential data input (odd data)
5 RxO2- Negative LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)
6 RxO2+ Positive LVDS differential data input (odd data, H-Sync, V-Sync,DSPTMG)
7 GND Power Ground
8 RxOC- Negative LVDS differential clock input (odd clock)
9 RxOC+ Positive LVDS differential clock input (odd clock)
10 RxO3- Negative LVDS differential data input (odd data)
11 RxO3+ Positive LVDS differential data input (odd data)
12 RxE0- Negative LVDS differential data input (Even clock)
13 RxE0+ Positive LVDS differential data input (Even data)
14 GND Power Ground
15 RxE1- Positive LVDS differential data input (Even data)
16 RxE1+ Negative LVDS differential data input (Even data)
17 GND Power Ground
18 RxE2- Negative LVDS differential data input (Even data)
19 RxE2+ Positive LVDS differential data input (Even data)
20 RxEC- Negative LVDS differential clock input (Even clock)
21 RxEC+ Positive LVDS differential clock input (Even clock)
22 RxE3- Negative LVDS differential data input (Even data)
23 RxE3+ Positive LVDS differential data input (Even data)
24 GND Power Ground
25 NC -
26 NC -
27 NC -
28 POWER Power
29 POWER Power
30 POWER Power
Note : Input signals of odd and even clock shall be the same timing.
--14--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
MST7111A
--15--
--16--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
--17--
24LC08
A0 1 8 VCC A0 1 8 VCC
A1 2 24C08 7 WP A1 2 24C08 7 WP
or or
A2 3 24LC08 6 SCL A2 3 24LC08 6 SCL
VSS 4 5 SDA VSS 4 5 SDA
Dual-In-Line SO package
package (M8)
A0 1 8 VCC
A1 2 24C08 7 WP
or
A2 3 24LC08 6 SCL
VSS 4 5 SDA
TSSOP
Pin Name
A0, A1 N.C.
A2 Device Address inputs
Vss Ground
SDA Data I/O
SCL Clock input
WP Write Protect
Vcc + 5 V or + 3 V
NOTE: These are STRESS rating only. Appropriate conditions for operating these devices given elsewhere
may permanently damage the part. Prolonged exposure to maximum ratings may affect device reliability.
--18--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
DC ELECTRICAL CHARACTERISTICS
(Vcc =5V +/- 10% ,MTV24C08/24LC08° Vcc =3V +/- 10% ,24LC08)
F
MTV24C08/
24LC08
Symbol Parameter Conditions 24LC08 Units
Min Max Min Max
SCL = 100KHZ
ICC1 Operating Current
CMOS Input Levels
— 10 — 8 mA
(Program)
Operating Current SCL = 100KHZ
ICC2 (Read) CMOS Input Levels
— 2 — 2 mA
ISB Standby Current SCL = SDA = 0 V — 10 — 10 µA
IIL Input Leakage VIN = 0 V to VCC -1 +1 -1 +1 µA
IOL Output Leakage VOUT = 0 V to Vcc -1 +1 -1 +1 µA
VIL Input Low Voltage -0.1 0.8 -0.1 0.15 VCC V
VIH Input High Voltage 2 VCC +0.2 0.8VCC VCC+0.2 V
VOL1 Output Low Voltage IOL = 2.1mA TTL — 0.4 — 0.4 V
VOH1 Output High Voltage IOH = -400uA TTL 2.4 — 2.4 — V
VOL2 Output Low Voltage IOL = 10uA CMOS — 0.2 — 0.2 V
VOH2 Output High Voltage IOH = -10uA CMOS VCC-0.2 — VCC-0.2 — V
Programming Command
VLK VCC Lockout Voltage
Can Be Executed
Default — Default — V
AC ELECTRICAL CHARACTERISTICS
(Vcc =5V +/- 10% , MTV24C08° F Vcc =3V +/- 10% ,24LC08)
(Vcc =5V +/- 10% , MTV24C08 Fast Mode)
MTV24C08/ MTV24C08
Parameter Symbol 24LC08 (Fast Mode) Units
Min Max Min Max
Clock frequency Fscl 0 100 — 400 kHz
Clock high time Thigh 4000 — 600 — ns
Clock low time Tlow 4700 — 1200 — ns
SDA and SCL rise time Tr — 1000 — 300 ns
SDA and SCL fall time Tf — 300 — 300 ns
START condition hold time Thd:Sta 4000 — 600 — ns
START condition setup time Tsu:Sta 4700 — 600 — ns
Data input hold time Thd:Dat 0 — 0 — ns
Data input setup time Tsu:Dat 250 — 100 — ns
STOP condition setup time Tsu:Sto 4000 — 600 — ns
Output valid from clock Taa 300 3500 100 900 ns
Bus free time Tbuf 4700 — 1200 — ns
Data out hold time Tdh 300 — 50 — ns
Input filter spike suppression Tsp — 100 — 50 ns
(SDA and SCL pins)
Write cycle time Twr — 10 — 10 ms
--19--
CAPACITANCE TA= 25∞C , f=250KHZ
--20--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
RC1117
RC1117X2.5
1A Adjustable/Fixed Low Dropout Linear Regulator
Features Description
• Low dropout voltage The RC1117 and RC1117-2.5, -2.85, -3.3 and -5 are low
• Load regulation: 0.05% typical dropout three-terminal regulators with 1A output current
• Trimmed current limit capability. These devices have been optimized for low voltage
• On-chip thermal limiting where transient response and minimum input voltage are
• Standard SOT-223, TO-263, and TO-252 packages critical. The 2.85V version is designed specifically to be
• Three-terminal adjustable or fixed 2.5V, 2.85V, 3.3V, 5V used in Active Terminators for SCSI bus.
Typical Applications
RC1117
R2
24.9
VOUT = VREF(1 + R2/R1) + IAdj • R2
RC1117-2.85
VIN = 5V VIN
+VOUT
2.85V at 1A
+
10 F 22 F
GND
--21--
Pin Assignments
Tab is
VOUT
Tab is
Front View VOUT
3 IN
Tab is
VOUT 2 OUT
1 ADJ/GND
1 2 3 1 2 3
*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane., JA can vary from
30°C/W to more than 50°C/W. Other mounting techniques may provide better thermal resistance than 30°C/W.
--22--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
Electrical Characteristics
Operating Conditions: VIN 7V, TJ = 25°C unless otherwise specified.
The denotes specifications which apply over the specified operating temperature range.
--23--
RC1117-3.3
Features Description
• Low dropout voltage The RC1117 and RC1117-2.5, -2.85, -3.3 and -5 are low
• Load regulation: 0.05% typical dropout three-terminal regulators with 1A output current
• Trimmed current limit capability. These devices have been optimized for low voltage
• On-chip thermal limiting where transient response and minimum input voltage are
• Standard SOT-223, TO-263, and TO-252 packages critical. The 2.85V version is designed specifically to be
• Three-terminal adjustable or fixed 2.5V, 2.85V, 3.3V, 5V used in Active Terminators for SCSI bus.
Typical Applications
RC1117
R2
24.9
VOUT = VREF(1 + R2/R1) + IAdj • R2
RC1117-2.85
--24--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
Pin Assignments
Tab is
VOUT
Tab is
Front View VOUT
3 IN
Tab is
VOUT 2 OUT
1 ADJ/GND
1 2 3 1 2 3
*With package soldered to 0.5 square inch copper area over backside ground plane or internal power plane., JA can vary from
30°C/W to more than 50°C/W. Other mounting techniques may provide better thermal resistance than 30°C/W.
--25--
Electrical Characteristics
Operating Conditions: VIN 7V, TJ = 25°C unless otherwise specified.
The denotes specifications which apply over the specified operating temperature range.
--26--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
SI4435
PD- 93768A
Si4435DY
HEXFETÆ Power MOSFET
- Ultra Low On-Resistance A
1
- P-Channel MOSFET S
8
D
- Surface Mount 2 7
VDSS = -30V
S D
- Available in Tape & Reel 3 6
S D
G
4 5
D RDS(on) = 0.020Ω
T o p V ie w
Description
These P-channel HEXFETÆ Power MOSFETs from
International Rectifier utilize advanced processing
techniques to achieve the extremely low on-resistance per
silicon area. This benefit provides the designer with an
extremely efficient device for use in battery and load
management applications..
Thermal Resistance
Parameter Max. Units
o
RθJA Maximum Junction-to-AmbientÉ 50 C/W
--27--
Si4435DY
Electrical Characteristics @ TJ = 25∞C (unless otherwise specified)
Parameter Min. Typ. Max. Units Conditions
V(BR)DSS Drain-to-Source Breakdown Voltage -30 ñññ ñññ V V GS = 0V, ID = -250µA
∆V(BR)DSS/∆TJ Breakdown Voltage Temp. Coefficient ñññ -0.019 ñññ V/∞C Reference to 25∞C, D I = -1mA
ñññ 0.015 0.020 VGS = -10V, ID = -8.0A Ç
RDS(on) Static Drain-to-Source On-Resistance Ω
ñññ 0.026 0.035 VGS = -4.5V, ID = -5.0A Ç
VGS(th) Gate Threshold Voltage -1.0 ñññ ñññ V VDS = VGS, ID = -250µA
gfs Forward Transconductance ñññ 11 ñññ S VDS = -15V, ID = -8.0A
ñññ ñññ -10 VDS = -24V, VGS = 0V
IDSS Drain-to-Source Leakage Current µA
ñññ ñññ -10 VDS = -15V, VGS = 0V, TJ = 70∞C
Gate-to-Source Forward Leakage ñññ ñññ -100 VGS = -20V
IGSS nA
Gate-to-Source Reverse Leakage ñññ ñññ 100 VGS = 20V
Qg Total Gate Charge ñññ 40 60 ID = -4.6A
Qgs Gate-to-Source Charge ñññ 7.1 ñññ nC VDS = -15V
Qgd Gate-to-Drain ("Miller") Charge ñññ 8.0 ñññ VGS = -10V Ç
td(on) Turn-On Delay Time ñññ 16 24 VDD = -15V, VGS = -10V Ç
tr Rise Time ñññ 76 110 ID = -1.0A
ns
td(off) Turn-Off Delay Time ñññ 130 200 RG = 6.0Ω
tf Fall Time ñññ 90 140 R D = 15Ω
Ciss Input Capacitance ñññ 2320 ñññ VGS = 0V
Coss Output Capacitance ñññ 390 ñññ pF VDS = -15V
Crss Reverse Transfer Capacitance ñññ 270 ñññ É = 1.0kHz
VSD Diode Forward Voltage ñññ ñññ -1.2 V TJ = 25∞C, SI = -2.5A, VGS = 0V Ç
trr Reverse Recovery Time ñññ 34 51 ns TJ = 25∞C, FI = -2.5A
Qrr Reverse Recovery Charge ñññ 33 50 nC di/dt = -100A/µs Ç
Notes:
Å Repetitive rating; pulse width limited by É Surface mounted on FR-4 board, t ≤ 5sec.
max. junction temperature.
--28--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
TDA7496L
BLOCK DIAGRAM
VAROUT_R VS
7 15,16
GND 1,2,3,13,
18,19,20 VOLUME
9 1000µF
INR + 14
470nF 30K - OUTR
OP AMP
S1 ST-BY
+5V
11 STBY
MUTE/STBY S_GND
10K
PROTECTIONS
12 MUTE
60K 1µF +5V
VOLUME S2 MUTE
4
INL + 17 OUTL
470nF 30K -
1000µF
OP AMP
SVR 10
470µF 6 5
VOLUME VAROUT_L
+5V
D97AU596A
300K
100nF
--29--
ABSOLUTE MAXIMUM RATINGS
Symbol Parameter Value Unit
VS DC Supply Voltage 26 V
VIN Maximum Input Voltage 8 Vpp
Ptot Total Power Dissipation (Tcase = 60∞C) 6 W
Tamb Ambient Operating Temperature 0 to 70 ∞C
Tstg, Tj Storage and Junction Temperature -40 to 150 ∞C
V6 Volume CTRL DC voltage 7 V
PIN CONNECTION Rth with "on board" Square Heatsink vs. cop-
per area.
Rthj-a D97AU675
GND 1 20 GND (∞C/W) COPPER AREA 35µ
THICKNESS
GND 2 19 GND
GND 3 18 GND
60
INL 4 17 OUTL
VAROUT_L 5 16 VS
PC BOARD
VOLUME 6 15 VS 50
VAROUT_R 7 14 OUTR
N.C. 8 13 GND
40
INR 9 12 MUTE
SVR 10 11 STBY
D97AU597A 30
0 4 8 12 Area(cm2)
THERMAL DATA
Symbol Parameter Value Unit
Rth j-pins Thermal Resistance Junction-pins max. 15 ∞C/W
Rth j-amb (*) Thermal Resistance Junction-ambient max. 50 ∞C/W
(*) Mounted on PCB with no heatsink
ELECTRICAL CHARACTERISTICS (Refer to the test circuit VS = 14V; RL = 8Ω, Rg = 50Ω, Tamb = 25∞C).
Symbol Parameter Test Condition Min. Typ. Max. Unit
VS Supply Voltage Range 10 18 V
Iq Total Quiescent Current 25 50 mA
DCVOS Output DC Offset Referred to No Input Signal 200 mV
SVR Potenial
VO Quiescent Output Voltage 7 V
PO Output Power THD = 10%; RL = 8Ω; 1 .6 2 W
THD = 1%; RL = 8Ω; 1 .3 W
THD Total Harmonic Distortion GV = 30dB; PO = 1W; f = 1KHz; 0.4 %
Ipeak Output Peak Current (internally limited) 0.7 0.9 A
Vin Input Signal 2.8 Vrms
GV Closed Loop Gain Vol Ctrl > 4.5V 28.5 30 31.5 dB
GvLine Monitor Out Gain Vol Ctrl > 4.5V; Zload > 30KΩ -1.5 0 1.5 dB
AMin VOL Attenuation at Minimum Volume Vol Ctrl < 0.5V 80 dB
BW 0.6 MHz
--30--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
APPLICATION SUGGESTIONS
The recommended values of the external components are those shown on the application circuit of fig-
ure 1A. Different values can be used, the following table can help the designer.
SUGGESTION LARGER THAN SMALLER THAN
COMPONENT PURPOSE
VALUE SUGGESTION SUGGESTION
R1 300K Volume control Larger volume regulation Smaller volume regulation
circuit time time
R2 10K Mute time constant Larger mute on/off time Smaller mute on/off time
P1 50K Volume control
circuit
C1 1000µF Supply voltage Danger of oscillation
bypass
C2 470nF Input DC decoupling Lower low frequency cutoff Higher low frequency cutoff
C3 470nF Input DC decoupling Lower low frequency cutoff Higher low frequency cutoff
C4 470µF Ripple rejection Better SVR Worse SVR
C5 100nF Volume control time Larger volume regulation Smaller volume regulation
costant time time
C6 1000µF Output DC Lower low frequency cutoff Higher low frequency cutoff
decoupling
C7 1µF Mute time costant Larger mute on/off time Smaller mute on/off time
C8 1000µF Output DC Lower low frequency cutoff Higher low frequency cutoff
decoupling
C9 100nF Supply voltage Danger of oscillation
bypass
--31--
NCP1117/NCP1117
NCP1117, NCV1117
Features Tab
ω Output Current in Excess of 1.0 A DPAK
ω 1.2 V Maximum Dropout Voltage at 800 mA Over Temperature DT SUFFIX
1 CASE 369C
ω Fixed Output Voltages of 1.5 V, 1.8 V, 2.0 V, 2.5 V, 2.85 V, 3.3 V, 3 2
1 3
5.0 V, and 12 V (Top View)
ω Adjustable Output Voltage Option
ω No Minimum Load Requirement for Fixed Voltage Output Devices
ORDERING INFORMATION
ω Reference/Output Voltage Trimmed to +1.0% See detailed ordering and shipping information in the package
ω Current Limit, Safe Operating and Thermal Shutdown Protection dimensions section on pages 11 and 12 of this data sheet.
ω Operation to 20 V Input
ω NCV Prefix for Automotive and Other Applications Requiring Site DEVICE MARKING INFORMATION
See general marking information in the device marking
and Control Changes section on page 13 of this data sheet.
ω Pb-Free Packages are A vailable
Applications
ω Consumer and Industrial Equipment Point of Regulation
ω Active SCSI Termination for 2.85 V Version
ω Switching Power Supply Post Regulation
ω Hard Drive Controllers
ω Battery Chargers
TYPICAL APPLICATIONS
110
--32--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
NCP1117, NCV1117
MAXIMUM RATINGS
Rating Symbol Value Unit
Input Voltage (Note 1) Vin 20 V
Output Short Circuit Duration (Notes 2 and 3) - Infinite -
Power Dissipation and Thermal Characteristics
Case 318H (SOT-223)
Power Dissipation (Note 2) PD Internally Limited W
Thermal Resistance, Junction-to-Ambient, Minimum Size Pad R JA 160 5C/W
Thermal Resistance, Junction-to-Case R JC 15 5C/W
Case 369A (DPAK)
Power Dissipation (Note 2) PD Internally Limited W
Thermal Resistance, Junction-to-Ambient, Minimum Size Pad R JA 67 5C/W
Thermal Resistance, Junction-to-Case R JC 6.0 5C/W
Maximum Die Junction Temperature Range TJ -55 to 150 5C
Storage Temperature Range Tstg -65 to 150 5C
Operating Ambient Temperature Range TA 5C
NCP1117 0 to +125
NCV1117 -40 to +125
Maximum ratings are those values beyond which device damage can occur. Maximum ratings applied to the device are individual stress limit
values (not normal operating conditions) and are not valid simultaneously. If these limits are exceeded, device functional operation is not implied,
damage may occur and reliability may be affected.
1. This device series contains ESD protection and exceeds the following tests:
Human Body Model 2000 V per MIL-STD-883, Method 3015.
Machine Model Method 200 V.
2. Internal thermal shutdown protection limits the die temperature to approximately 1755C. Proper heatsinking is required to prevent activation.
The maximum package power dissipation is: TJ(max) TA
PD
R JA
3. The regulator output current must not exceed 1.0 A with Vin greater than 12 V.
--33--
NCP1117, NCV1117
ELECTRICAL CHARACTERISTICS (Cin = 10 F, Cout = 10 F, for typical value TA = 255C, for min and max values TA is the
operating ambient temperature range that applies unless otherwise noted. (Note 6)
--34--
L70S+/L70S+(Lift Stand),L72S,L72S(Lift Stand) Technical Service Manual
NCP1117, NCV1117
ELECTRICAL CHARACTERISTICS (Cin = 10 F, Cout = 10 F, for typical value TA = 255C, for min and max values TA is the
operating ambient temperature range that applies unless otherwise noted. (Note 7)
Quiescent Current IQ mA
1.5 V (Vin = 11.5 V) - 3.6 10
1.8 V (Vin = 11.8 V) - 4.2 10
2.0 V (Vin = 12 V) - 4.5 10
2.5 V (Vin = 10 V) - 5.2 10
2.85 V (Vin = 10 V) - 5.5 10
3.3 V (Vin = 15 V) - 6.0 10
5.0 V (Vin = 15 V) - 6.0 10
12 V (Vin = 20 V) - 6.0 10
Thermal Regulation (TA = 255C, 30 ms Pulse) - 0.01 0.1 %/W
Ripple Rejection (Vin-V out = 6.4 V, Iout = 500 mA, 10 Vpp 120 Hz Sinewave) RR dB
Adjustable 67 73 -
1.5 V 66 72 -
1.8 V 64 70 -
2.0 V 64 70 -
2.5 V 62 68 -
2.85 V 62 68 -
3.3 V 60 64 -
5.0 V 57 61 -
12 V 50 54 -
Adjustment Pin Current (Vin = 11.25 V, Iout = 800 mA) Iadj - 52 120 A
Adjust Pin Current Change Iadj - 0.4 5.0 A
(Vin-V out = 1.4 V to 10 V, Iout = 10 mA to 800 mA)
--35--
5 4 3 2 1
BLOCK DIAGRAM
MODEL NAME : L70S+, L72S
D D
14.318MHz
17"
Analog Scaler LCD
R. G. B PANEL
(MST 7111A) LVDS
C C
(TSU16AL)
POWER &
INVERTER
B
MCU B
24MHz
AUDIO SPK
A
HYUNDAI ImageQuest A
Title
<Title> L70S+, L72S
Size Document Number Rev
Custom<Doc> BLOCK DIAGRAM <RevCode>
Date: Monday, December 27, 2004 Sheet 1 of 1
5 4 3 2 1
L70SP, L70SP(Lift Stand) / L72S, L72S(Lift Stand)
6/ 1
NO LOCATION PART NUMBER DESCRIPTION REMARK
6/ 2
NO LOCATION PART NUMBER DESCRIPTION REMARK
6/ 3
NO LOCATION PART NUMBER DESCRIPTION REMARK
6/ 4
NO LOCATION PART NUMBER DESCRIPTION REMARK
6/ 5
NO LOCATION PART NUMBER DESCRIPTION REMARK
6/ 6
5 4 3 2 1
D D
VCC2.5VD
VCC12V VCC5V
TSU16AL(RC1117-1.8V)
VCC5V VCPU
U1
C2 RC1117S2.5T
47uF/16V
3 VIN VOUT 2
DIP_2.0P1
12V
1 C9 C10
5V C7 C8 GND
2
3 0.1uF/1608 47uF/16V
GND 47uF/16V 0.1uF/1608 1
4
5 On/Inverter
6 Adj/Backlite onBACKLITE
7 AdjBACKLITE GND
0V : MAX BRIGHTNESS GND
CON1 5V : MIN BRIGHTNESS
Board In Type GND GND GND
to
Inverter/power VCC3.3VD
VCC3.3V_AV
U3
RC1117S3.3T VCC3.3V_PL
3 2 VCC3.3VD_PL
C C3
VIN
GND
VOUT
C
C4
C17 C18
47uF/16V 0.1uF/1608 1
47uF/16V 0.1uF/1608
GND
GND
GND GND
GND
R4
VCC5V 1K
VLCD
onPANEL
ACTIVE LOW
U2
B 1
2
S
S
D
D
8
7 B
3 6 C11 C12
S D
4 G D 5
47uF/16V 0.1uF/1608
C13 C14 C15 SI4435 SO8
GND
HYUNDAI ImageQuest
A Title A
L70S+, L72S
D D
CN1
11 1 R8 C20 0.1uF/1608
RIN0
6 100
12 2 R11 C21 0.1uF/1608
GIN0
7 100
13 3 R14 C22 0.1uF/1608
BIN0
8 100
14 4 C23 open
SOG0
2
9 R21 R17 R18
15 5 D1 D2 D3 75 75 75 R19 C24 0.1uF/1608
GNDR0
10 100
KDS226 KDS226 KDS226
DSUB-15 R22 C28 0.1uF/1608
3
GNDG0
VCPU 100
ISP_DAT
ISP_CLK
R26 20
HSI R27 0
HSYNC0
VSI R28 R29 100
VSYNC0
C 0
R34 100
ST_DET0
C
D4 R35 R36
D5 D6
C30 open C31 4.7K
6.2V 220P
6.2V 6.2V 5P
D7 D8
6.2V 6.2V
B B
HYUNDAI ImageQuest
Title
A A
L70S+, L72S
Size Document Number Rev
VGA_INPUT
D 3.3VD_PL [TSU16AL(1.8V)] D
3.3V_PL 3.3VD 2.5VD
3.3V_AV 3.3V_DVI
VCC3.3VD
18
28
16
98
14
43
47
54
64
76
90
46
50
67
87
U4
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
AVDD
AVDD
VDDC
VDDC
VDDC
VDDC
AVDD_PLL
AVDD_PLL
AVDD_DVI
AVDD_DVI
0.1uF 0.1uF
Y1
AVSS_PLL
AVSS_PLL
AVSS_DVI
AVSS_DVI
14.318MHZ
GNDC
GNDC
GNDC
GNDC
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
GNDP
AVSS
AVSS
AVSS
AVSS
97 XOUT
C58
22pF
19
27
31
17
99
11
44
48
51
55
65
77
89
45
49
66
88
2
HYUNDAI ImageQuest
Title
A A
L70S+,L72S
VCPU
VCPU
D open
R40 R83
D
R42 4.7K
10K
C59
R43 0.1uF/1608
VOLUME
C60 8.2K VCPU
0.1uF
C63 C61 C62
22PF/1608 0.1uF/1608
C64 4.7uF/25V
47uF/16V R44
4.7K
Y2 R45
6
1M U5
24MHZ
9 34
VDD5
VDD3
XTAL1 PD.0 AdjBACKLITE
PD.1 35 R46
10 36 C66 VCPU
XTAL2 PD.2 200
VCPU 37 0.1uF/1608
C65 PD.3
22PF/1608 5 RESET PD.4 38
PD.5 39
1 PE.3 PD.6 40
R47 R49 R50
MUTE 2 PE.2 PD.7 43
10K 4.7K 4.7K
3 PE.1
ST-DET1 VCPU
4 PE.0 PB.6/SDA2 11
PB.5/SCL2 12
INT 16 INT0/PB.1 PB.4 13
14 R52 100
PB.3 onPANEL R53
PB.2 15 4.7k
R54 150 26 17 R55 100
PA0/SDA1 PB.0 HWRESET R58
R56 150 27 18 HFS
C 28
PA1/SCL1
PA.2
PC.7
PC.6 19 HCLK
22K
onBACKLITE C
3
R57 470 29 20 R61
PA.3 PC.5 HDATA 10K
R59 470 30 21 1 Q2
R60 PA.4 PC.4
470 31 22 C68 C67
R64 PA.5 PC.3
470 32 23 0.1uF/1608 0.1uF/1608
R65 PA.6 PC.2 TT2N3904D
2
470 33 24
PA.7 PC.1 VCPU
PC.0 25
R66 200 41
VSS
HSYNC0 R67 200 HIN R68 1K
42 VIN NC 44
VSYNC0
VCPU
R69 1K
WT61P4 PLCC
8
C69 C70
open 470pF/1608 C72
C71 open
8
7
6
5
open
RN1
4.7K VCPU
R70
1
2
3
4
750 R71
750
ISP_DAT C73 U6
ISP_CLK 0.1uF/1608 1 A0 VCC 8
2 A1 WP 7
3 6 R72 100
A2 SCL R73 100
4 GND SDA 5
24C08
B MENU 1
2
R3
R5
100
100
B
SELECT R6 100
DOWN 3
4 R7 100
UP
GND 5
6 LED_G
LED-G LED_O
LED-O 7
8 R9 100
PWR-SW
AUDIO/GL 9 L/GND
AUDIO/L 10 AUDIO/L
AUDIO/RG 11 R/GND
AUDIO/R 12 AUDIO/R
CN2 C1 C5 C16 C19 C25
0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
to KEY PAD
OPTION(ESD 대책)
HYUNDAI ImageQuest
Title
A L70S+, L72S A
D D
LVA[0..9]
LVA[0..9]
VLCD
CON4
1
2
3
4
5
6
LVA6 R90 0 RXE3+ 7
LVA7 R91 0 RXE3- 8
LVA8 R92 0 RXEC+ 9
LVA9 R93 0 RXEC- 10
LVA4 R94 0 RXE2+ 11
LVA5 R95 0 RXE2- 12
13
LVA2 R96 0 RXE1+ 14
LVA3 RXE1- 15
C R97 0
16
17
DUAL LVDS C
LVA0 R98 0 RXE0+
LVA1 R99 0 RXE0- 18
LVB6 R100 0 RXO3+ 19
LVB7 R101 0 RXO3- 20
LVB8 R102 0 RXOC+ 21
LVB9 R103 0 RXOC- 22
23
LVB4 R104 0 RXO2+ 24
LVB5 R105 0 RXO2- 25
LVB2 R106 RXO1+ 26
0
LVB3 R107 0 RXO1- 27
LVB0 R108 0 RXO0+ 28
LVB1 R109 0 RXO0- 29
30
CON30
LVB[0..9]
LVB[0..9]
B B
HYUNDAI ImageQuest
Title
A L70S+,L72S A
D D
VCC12V
VCC5V
3
C74
C75
R77
Q5 2
TT2N3904D MUTE
J1 R88 U7 10K
0.1uF
47uF/16V
1
1K
9 INR Vs 15
C C76 0.47UF C
TDA7496L Vs 16 R78
4 GND 150 J2
C77 0.47UF INL
R89 14
1K
OUTR C78
R/GND
1608/HB60 4 △
11 330uF/16V L10
STBY R80 1K AUDIO/R 3
VOLUME 6 VOLUME L11
AUDIOJACK 12 AUDIO/L 2
R79
1K C79
MUTE L/GND 1608/HB60
1
▽
GND OUTL 17
47uF/16V C80 330uF/16V 5
R84 R85 R81
270 270 7 VAROUT_R 150
GND 1 EARPHONE JACK
5 VAROUT_L GND 2
3 C83
GND 0.1uF R82 GND
GND GND 13
GND 10K
GND 18
GND 19
GND
10 SVR GND 20
GND
C84 GND
330/16V
B B
GND
A A
HYUNDAI ImageQuest
Title
L70S+,L72S
!" #
$
%
" &'
() *+
$
,- #
,
( ,- * ,
$
!,' "
.%&'/
$
A B C D E F G H I J K L
13
16
1 1
14
2 2
15
18
5 10
19
3 3
4
11
17
6
12
4 4
20
21
6 5001000666 SCREW SCR-MC,BIN+MC3X5 4
5 FRAME ASSY 1
0
4 LCD MODULE SEC 1
22
3 6220856 LENS LED PMMA 1
'05.01.11 '05.01.21
N
S EXPLODED VIEW 00
MDL
L70SP/L70DP
SHEET
SIZE
DWG NO. 1
REF A2
NO. LIFT 1
TAMP 031-2 A B C D E F G H I J K FILE NAME : EXPLODED VIEW
A B C D E F G H I J K L
1 1
14
15
24
2 25 2
13
16
17
12
3 11 3
10
19 18
5
6
'05.01.11 '05.01.21
N
S EXPLODED VIEW 00
MDL
L70SP/L70DP
SHEET
SIZE
DWG NO. 1
REF
NO.
A2 1
TAMP 031-2 A B C D E F G H I J K FILE NAME : EXPLODED VIEW