Академический Документы
Профессиональный Документы
Культура Документы
Wiring Device-Kellems
Features
• T-weld construction prevents snags • Use factory support hardware or fabricate
• 5mm round wire minimum supports at the job site
• High load rating • Painted tray includes factory installed
masking to ensure proper grounding at
• Easy to cut and fabricate fittings in the field
splices; no need to remove paint
• 100% recycled steel during installation
• 2" x 4" mesh opening
Features
• T-weld construction prevents snags • Use factory support hardware or fabricate
• 5mm round wire minimum supports at the job site
• High load rating • Electroplated zinc galvanized (post plated)
made from cabon steel and plated to
• Easy to cut and fabricate fittings in the field
ASTM B 633, Type III, SC-1
• 2" x 4" mesh opening
.1969" Dia.
18" (457) • 116 37 9 9 HBT0818ZP
"Round" Wire Design W 20" (508) • 116 39 9 9 HBT0820ZP
Note: •UL Classified/cUL Classified as equipment ground conductor.
All dimensions are +/- 0.25".
*See page 13 for details.
See page 14 for wire fill and maximum load chart.
Features
• Flat shaped cross-wires provide significantly • Reduction in stress helps maintain Cat 6
more surface area to support weight and Cat 6A performance
of cables • Cuts and configures the same as round
• Flat ribs provide 400% more surface area wire tray
and reduce stress on cables by 60% • Uses the same splicing and mounting
• 100% recycled steel hardware as round wire tray
• 2" x 4" mesh opening
Features Applications
• Type 304L and 316S stainless steel • Food processing
• Meets ASTM A580 specifications • Wash down areas
• 4.5mm round wire minimum • Corrosive environments
• Stainless splice kits and ceiling supports • Outdoor installations
are available • Marine
Features
• T-weld construction prevents snags • Use factory support hardware or fabricate
• 5mm round wire on smaller sizes supports on the job site
• 100% recycled steel • 2” x 4” mesh opening
Tray Length
Tray Height Tray Width 24" (610) 48" (1,220) 72" (1,829)
Wire Diameter 2" Deep Tray 6" (152) HBTU020624 HBTU020648 HBTU020672
12" (305) HBTU021224 HBTU021248 HBTU021272
5mm 24" (610) HBTU022424 HBTU022448 HBTU022472
4" Deep Tray 6" (152) HBTU040624 HBTU040648 HBTU040672
.1969" Dia.
12" (305) HBTU041224 HBTU041248 HBTU041272
"Round" Wire Design 24" (610) HBTU042424 HBTU042448 HBTU042472
6" Deep Tray 6" (152) HBTU060624 HBTU060648 HBTU020672
12" (305) HBTU061224 HBTU061248 HBTU061272
24" (610) HBTU062424 HBTU062448 HBTU062472
8" Deep Tray 6" (152) — — —
12" (305) HBTU081224 HBTU081248 HBTU081272
20" (610) HBTU082024 HBTU082048 HBTU082072
Flat 24" (610) HBTU002424 — —
HBTU002424 Note: Tray UL Classified as equipment ground conductor.
2. Attach first tray with washer support and 4. Attach second tray
¼"-20 nut and bolt
90 Degree Radius
Tray Width Traditional Configuration Hubbell Pre-Formed Fittings Time Savings
2x8 7 Minutes 1 Minute 85%
4 x 12 20 Minutes 2 Minutes 90%
Tee
Tray Width Traditional Configuration Hubbell Pre-Formed Fittings Time Savings
4 x 12 8 Minutes, 45 seconds 2 Minutes, 30 seconds 70%
4 x 18 10 Minutes 2 Minutes, 30 seconds 74%
Intersection
Tray Width Traditional Configuration Hubbell Pre-Formed Fittings Time Savings
6 x 24 29 Minutes 4 Minutes, 45 seconds 83%
Features
• Labor and time savings • Steel pre-galvanized bases
• Consistent installations • Interlocking polymer side walls
• For round and flat tray • Splicing hardware included
No Splice supports reduces the number of splice kits required for tray installations.
No Splice Support*
Center Support Ceiling Support
Qty. per Qty. per
Tray Width Box Pre-Galvanized Black Powder Coat Box Pre-Galvanized Black Powder Coat
6" (152) 1 HBTNSCTRS6 HBTNSCTRS6BK - – –
8" (203) 1 HBTNSCTRS8 HBTNSCTRS8BK - – –
12" (305) 1 HBTNSCTRS12 HBTNSCTRS12BK 1 HBTNSCLGS12 HBTNSCLGS12BK Center Support
Supports**
Center Support Ceiling Support Trapeze Support
Qty. per Qty. per
Tray Width Box Pre-Galvanized Black Powder Coat Pre-Galvanized Black Powder Coat Box Zinc Plated Black Powder Coat
4" (102) 1 HBTCTRS4 HBTCTRS4BK – – 50 HBTTS HBTTSBK
6" (152) 1 HBTCTRS6 HBTCTRS6BK – – Attaches to the side of the tray;
8" (203) 1 HBTCTRS8 HBTCTRS8BK – – for tray sizes 16" wide and smaller;
use in pairs every 6 feet for 4" and
12" (305) 1 HBTCTRS12 HBTCTRS12BK HBTCLGS12 HBTCLGS12BK 6" trays; can be staggered every 5 feet.
16" (406) 1 HBTCTRS16 HBTCTRS16BK HBTCLGS16 HBTCLGS16BK
18" (457) 1 HBTCTRS18 HBTCTRS18BK HBTCLGS18 HBTCLGS18BK
20" (508) 1 HBTCTRS20 HBTCTRS20BK HBTCLGS20 HBTCLGS20BK
24" (610) 1 HBTCTRS24 HBTCTRS24BK HBTCLGS24 HBTCLGS24BK
Brackets**
L-Bracket C-Bracket Shelf Support
Qty. per
Tray Width Box Pre-Galvanized Black Powder Coat Pre-Galvanized Black Powder Coat Pre-Galvanized Black Powder Coat
4" (102) 1 HBTLB4 HBTLB4BK HBTCB4 HBTCB4BK HBTSS4 HBTSS4BK
6" (152) 1 HBTLB6 HBTLB6BK – – HBTSS6 HBTSS6BK
8" (203) 1 HBTLB8 HBTLB8BK HBTCB8 HBTCB8BK HBTSS8 HBTSS8BK
12" (305) 1 HBTLB12 HBTLB12BK HBTCB12 HBTCB12BK HBTSS12 HBTSS12BK
16" (406) 1 HBTLB16 HBTLB16BK – – HBTSS16 HBTSS16BK
18" (457) 1 HBTLB18 HBTLB18BK HBTCB18 HBTCB18BK HBTSS18 HBTSS18BK
20" (508) 1 HBTLB20 HBTLB20BK – – HBTSS20 HBTSS20BK
24" (610) 1 HBTLB24 HBTLB24BK – – HBTSS24 HBTSS24BK
Note: **Install every 6 feet.
Cutting Tool
Weight Qty. per
Description (Lb/each) Box Catalog Number
Manual offset angled cutting 6.0 1 HBTCUTTOOL
tool, 24" leveraged handle
2.01 ACCEPTABLE MANUFACTURES 3. Wire basket shall be made of high strength steel wires and
formed into a standard 2-inch by 4-inch wire mesh pattern
1. Manufacturer: Subject to compliance with these specifications
with intersecting wires welded together. All mesh sections
wire basket tray systems to be installed shall be Hubbell
must have at least one bottom longitudinal wire along entire
“HBT” series.
length of straight section.
4. Wire basket sizes shall conform to the following
2.02 WIRE TRAY SECTIONS AND COMPONENTS nominal criteria:
1. Provide wire basket of types and sizes indicated with all A. Straight sections shall be furnished in standard
required splicing and mounting hardware. Construct units 118" (3m) lengths.
with T-weld edges and smooth surfaces in compliance
B. Wire diameter shall be 0.195" (5mm) minimum on all
with applicable standards and with the following additional
mesh sections. Wire diameter shall be minimum size of
construction features.
4.5mm on stainless steel.
A. All straight section longitudinal wires shall be
C. Wire basket shall have a 2-inch usable loading depth by
constructed with a continuous top wire safety edge.
(4), (6), (8), (10), (12), (14), (16), (18), (20), (22), (24), (26),
Safety edge must be T-welded on all tray sizes.
(28), (30), (32) inches wide.
B. Wire basket cross-wire to be constructed with either flat
D. Wire basket shall have a 4-inch usable loading depth by
shaped wire design or with round wire design as directed
(4), (6), (8), (10), (12), (14), (16), (18), (20), (22), (24), (26),
by engineer.
(28) inches wide.
- Flat shaped cross wire design shall provide additional
surface area for cable weight support and to avoid E. Wire basket shall have a 6-inch usable loading depth by
pressure points and strain on cables. (8), (10), (12), (14), (16), (18), (20), (22), (24) inches wide.
- Round shaped cross wire design may be used in F. Wire basket shall have an 8-inch usable loading depth by
general purpose applications where cable weight and (8), (10), (12), (14), (16), (18), (20) inches wide.
strain are not concerns.
5. All fittings shall be field formed from straight sections in
2. Materials and Finishes: Material and finish specifications for accordance with manufacturer’s instructions.
Carbon Steel Wire and Pre-Galvanized steel wire are
as follows: 6. All Tray sections and splicing assemblies shall be UL/C-UL
Classified as an Equipment Ground Conductor (EGC).
A. Pre-galvanized Zinc: Straight section shall be made from
pre-galvanized steel meeting the minimum mechanical 7. Wire mesh basket tray supports shall be ceiling trapeze
properties of ASTM A 641. Material must be cleaned type, center support, trapeze clips, or wall brackets as
after fabrication to remove any soot, manufacturing manufactured by Hubbell.
residue/oils or metallic particles. 8. Special accessories shall be furnished as required to
B. Powder Coat: Straight sections shall be powder protect, support and install a wire basket support system.
coated black with an average paint thickness of 1.2mils
(30microns) to 3.0mils (75microns). Hubbell powder coat
product is masked at splice points to allow conductive
ground design; no field paint removal is required.
C. Stainless Steel: Straight sections and accessories shall
be made from AISI Type 304L, 316L Stainless Steel
(meeting the minimum mechanical properties of
ASTM A 580).
D. Electro-Plated Zinc Galvanized (Post Plated) Made from
Carbon Steel and plated to ASTM B 633, Type III, SC-1.
E. Hot Dip Galvanized: Plain steel (ASTM AS10) dip after
fabricated and formed. ASTM A123.
Wiring Device-Kellems
Cable Management
Online Resources
Delivery eTour
This interactive, virtual tour of a city takes
visitors through various commercial settings.
As users navigate their way through the virtual
city, the eTour demonstrates where and how
Hubbell Delivery Systems products can be
deployed in the floor, through the floor, on the
wall, on the surface and from floor to ceiling
and demonstrates solutions in these spaces. BIM Models
Visit www.hubbell-wiring.com to take the tour. Visit www.hubbell-wiring.com
or seek.autodesk.com to
download all Hubbell Wiring
device BIM Models.
Office
Data
Center
Delivery Systems
eLearning Course
This course familiarizes the
Product Page user with Hubbell Delivery
Systems, where they can be
Literature Support used, the broad offering and
Hubbell offers an extensive literature library for product support. proper applications.
Downloadable PDFs are available online at www.hubbell-wiring.com
under the Media tab.
Complete more projects, on-time, more profitably, Black Ivory Gray Office White White Clear Anodized
Aluminum
with Nobody
Hubbelldelivers
Pre-Wired Raceway
like Hubbell Systems…
Commercial Solutions www.hubbell-wiring.com
®
www.hubbell-wiring.com
Wiring Device-Kellems
Hubbell Wiring Device-Kellems • Hubbell Incorporated (Delaware) • 40 Waterview Drive • Shelton, CT 06484 • Phone (800) 288-6000 • FAX (800) 255-1031
Printed in U.S.A. Specifications subject to change without notice.
®
is a registered trademark of Hubbell Incorporated. WLBD012 10/16