Академический Документы
Профессиональный Документы
Культура Документы
DATA
NORTH AMERICA EUROPE ASIA EARTHMOVER TYRES
Michelin Tire Corporation Michelin Michelin Asia Ltd BRO
One Parkway South 23, place des Carmes Bât. A1 21/F, Capital Tower Beijing,
PO Box 19001 - Greenville, South 63040 Clermont-Ferrand Cedex 9 No. 6 Jia Jianguomenwai
Carolina 29602-9001 France Avenue, Chaoyang district,
USA Beijing 100022
Fax : + 33 (0)4 73 32 27 47
Fax : + 1 864 458 4609 Fax : + 86 10 8567 9920
www.michelin.com/earthmover
www.michelingeniecivil.com
F16354 - Tél. 04 73 73 25 25
www.michelinearthmover.com
2009 EDITION
TECHNICAL DATA EARTHMOVER TYRES
3
CONTENTS
TYRE CONSTRUCTION 10
EXPLANATIONS 12 to 15
- FOR WORKING MACHINES : COMPACT LOADERS, BACKHOES, AND TELESCOPIC HANDLERS 88 & 89
- FOR COMPACTORS 91
70 series
The H/S aspect ratio is approximately equal to 0.70
The section width is given in millimeters followed
70
by the number 70
e.g.: 555/70 R 24
65 series
The H/S aspect ratio is approximately equal to 0.65
The section width is given in inches or in millimeters
followed by the number 65.
e.g.: 35/65 R 33 750/65 R 25
Type A: Particularly resistant to cuts, tread tearing and abrasion at average speeds which are higher than those for A4 (above).
Type B4: Compromise solution between abrasion resistance and average speed on rough surfaces.
(available in sizes 49 inch rim diameter and above)
Type B: Higher resistance to internal heat generation on surfaces which are not particularly rough.
Type C4: For running on long cycles at high speeds on well maintained roads.
Type C: Very high resistance to high average speeds on long cycles run on well maintained roads..
TECHNICAL DATA EARTHMOVER TYRES
5
IDENTIFICATION OF EARTHMOVER TYRES
D
N SUPER D1
D2
External Ø
External Ø
R: Radial construction
Note that earthmover tyres have a Load Index / Speed Symbol (see example)
or one or several stars.
The type of tread rubber (A, A4, B, B4, C, C4) and the tread depth (SUPER, D1, D2) may also be shown.
TECHNICAL DATA EARTHMOVER TYRES
6
LOAD INDEX - SPEED SYMBOL
maximum load maximum load maximum load maximum load maximum load
LI LI LI LI LI
kg lb kg lb kg lb kg lb kg lb
120 1 400 3 090 150 3 350 7 390 180 8 000 17 640 210 19 000 41 890 240 45 000 99 210
121 1 450 3 200 151 3 450 7 610 181 8 250 18 190 211 19 500 43 000 241 46 250 101 960
122 1 500 3 310 152 3 550 7 830 182 8 500 18 740 212 20 000 44 100 242 47 500 104 720
123 1 550 3 420 153 3 650 8 050 183 8 750 19 290 213 20 600 45 420 243 48 750 107 470
124 1 600 3 530 154 3 750 8 270 184 9 000 19 840 214 21 200 46 750 244 50 000 110 250
125 1 650 3 640 155 3 875 8 540 185 9 250 20 390 215 21 800 48 070 245 51 500 113 540
126 1 700 3 750 156 4 000 8 820 186 9 500 20 940 216 22 400 49 390 246 53 000 117 950
127 1 750 3 860 157 4 125 9 090 187 9 750 21 500 217 23 000 50 700 247 54 500 120 150
128 1 800 3 970 158 4 250 9 370 188 10 000 22 050 218 23 600 52 040 248 56 000 123 480
129 1 850 4 080 159 4 375 9 650 189 10 300 22 710 219 24 300 53 580 249 58 000 127 890
130 1 900 4 190 160 4 500 9 920 190 10 600 23 370 220 25 000 55 120 250 60 000 132 300
131 1 950 4 300 161 4 625 10 200 191 10 900 24 030 221 25 750 56 780 251 61 500 135 580
132 2 000 4 410 162 4 750 10 470 192 11 200 24 690 222 26 500 58 430 252 63 000 138 890
133 2 060 4 540 163 4 875 10 750 193 11 500 25 360 223 27 250 60 070 253 65 000 143 300
134 2 120 4 670 164 5 000 11 020 194 11 800 26 020 224 28 000 61 740 254 67 000 147 710
135 2 180 4 810 165 5 150 11 350 195 12 150 26 790 225 29 000 63 940 255 69 000 152 120
136 2 240 4 940 166 5 300 11 690 196 12 500 27 560 226 30 000 66 150 256 71 000 156 530
137 2 300 5 070 167 5 450 12 020 197 12 850 28 330 227 30 750 67 790 257 73 000 160 930
138 2 360 5 200 168 5 600 12 350 198 13 200 29 100 228 31 500 69 460 258 75 000 165 340
139 2 430 5 360 169 5 800 12 790 199 13 600 29 990 229 32 500 71 660 259 77 500 170 660
140 2 500 5 510 170 6 000 13 230 200 14 000 30 870 230 33 500 73 870 260 80 000 176 400
141 2 575 5 680 171 6 150 13 560 201 14 500 31 970 231 34 500 76 070 261 82 500 181 880
142 2 650 5 840 172 6 300 13 890 202 15 000 33 070 232 35 500 78 280 262 85 000 187 390
143 2 725 6 010 173 6 500 14 330 203 15 500 34 180 233 36 500 80 480 263 87 500 192 900
144 2 800 6 170 174 6 700 14 770 204 16 000 35 280 234 37 500 82 690 264 90 000 198 450
145 2 900 6 390 175 6 900 15 210 205 16 500 36 380 235 38 750 85 430 265 92 500 203 920
146 3 000 6 610 176 7 100 15 650 206 17 000 37 480 236 40 000 88 200 266 95 000 209 440
147 3 075 6 780 177 7 300 16 090 207 17 500 38 590 237 41 250 90 940 267 97 500 214 950
148 3 150 6 950 178 7 500 16 530 208 18 000 39 690 238 42 500 93 710 268 100 000 220 500
149 3 250 7 170 179 7 750 17 090 209 18 500 40 790 239 43 750 96 470 269 103 000 227 370
SPEED SYMBOLS
The SPEED SYMBOL indicates the maximum speed at which the tyre can carry a load corresponding to its load index,
under specified conditions.
Symbol A2 A3 A4 A5 A6 A8 B C D E F G
speed (km/h) 10 15 20 25 30 40 50 60 65 70 80 90
speed (mph) 6 9 12 15 19 25 31 37 40 43 50 56
It is imperative:
- do not exceed the permited max. speed of the tyre
- do not exceed the permited max. distances in one hour indicated in the tables
of tyre's characteristic
- At the time of fitting , it is vital that the various markings be checked , in order to be certain that the tyre is suitable
for operation at the maximum allowed vehicle speed and load.
TECHNICAL DATA EARTHMOVER TYRES
7
MAXIMUM PLY RATING (PR) AND CORRESPONDING STAR (*)
MARKING ON MICHELIN RADIAL TYRES
(1) no corresponding PR in these sizes which are only made in radial construction.
Use code: C: Compactor Index: S: smooth (mine, hard ground) 4: rock (deep tread)
G: Grader 1: ribbed (smooth surfaces) 5: rock (extra deep tread)
E: Earthmoving 2: traction (regular) 7: “flotation” (work on yielding surfaces)
L: Loader and Bulldozer 3: rock (regular)
Standardized identification code
Michelin tread patterns to be equated with the codes opposite
Code Tread pattern Application
C1 SMOOTH COMPACTOR X LC
E1 RIBBED X RIB
E2 TRACTION XGC, X-CRANE AT, XLB, XMP, XMH (S), XS, XSNOPLUS Indice E, XVC
E3 ROCK TRANSPORT XAD 65, XADN, XHAD, XK, XMS, XTS, XR, XRDN, XDC, XDM
X-SUPER TERRAIN AD, XADT, X-HAUL, X-QUARRY (S), XDT, X-TRACTION RD (S)
E4 ROCK (deep tread) XRS, XZH, XHD1, XDM, XDR, XKD1,
E7 “FLOTATION” X RIB, XS
G1 RIBBED
G2 TRACTION XGLA2, XMPS, X SNOPLUS, XTLA
G3 ROCK GRADER XHA2, XHA, XHAD, XHF, XLD, XRA, XRDN
G4 ROCK (deep tread) XLD D1, XRD1
G5 ROCK (extra-deep tread) XLD D2
L2 TRACTION XGLA2, XMCL, XM27, XM37, XMPS, XSNOPLUS, XTLA
L3 ROCK XHA2, XHA, XHF, XLD, XKA, XR, XRDN, XZSL, STABIL’X XZSL
L4 ROCK (deep tread) LOADER XKD1, XLD D1, X MINE D1, XR D1
L5 ROCK (extra-deep tread) BULLDOZER XLD D2, X MINE D2, XR D2
L3S SMOOTH XSM DN
L4S SMOOTH (deep tread)
L5S SMOOTH (extra-deep tread) XSMD2+
MICHELIN complementary identification: T = Traction, R = Rock, V = speed, F = Flotation, P = Multi purpose, S/R = Smooth/Rock
e.g.: L3T “Rock tyre (L3; Standardized identification code) where traction is needed (T; Michelin code)”
TECHNICAL DATA EARTHMOVER TYRES
8
MICHELIN EARTHMOVER TYRE RANGE
XHA - XHF L3F XLD L3T XLD SUPER L3T XLDD1 - XLDD2 XRDN - XRD1 - XRD2
XHAD - XHD1 XAD 65-1 SUPER E3T XADN E3T /E3V X-SUPER TERRAIN AD E4T XADT E4T
The casing
The crown
is made up of several
is not stabilized.
criss-crossed plies.
Disadvantages:
- accelerated wear.
- less grip.
- increased fuel consumption.
Advantages:
- longer tyre life.
- better traction on all types
of surface.
- lower fuel consumption due to
lower rolling resistance.
- improved comfort.
- increased resistance
to punctures / flats.
- increased resistance to heating
TECHNICAL DATA EARTHMOVER TYRES
11
MICHELIN TYRE CHARACTERISTICS
CONTENTS
* The values of R’ and rolling circumference given for our tyres on the characteristic pages apply to nominal conditions of load
and pressure (corresponding to the gray square of the load data).
The dimensions shown in this documentation correspond with that indicated above and follow the existing standards (E.T.R.T.O., ...).
The dimensional data is given for information purposes only and may change. It cannot be used for any legal purposes.
The standardized dimensions shown are the “maximum in service”.
TECHNICAL DATA EARTHMOVER TYRES
13
CHARACTERISTICS OF MICHELIN EARTHMOVER TYRES
The economic load and pressure limits are shown highlighted in the load/pressure table.
Generally, these are the nominal conditions for the tyre as defined in International Standards.
Loaders:
Front Tipping This table is used when the only information available is that of the operating weight and tipping load of the loader.
Front Laden This table is used in priority. The loads come from the weighing of the loader or the axle weight given by the manufacturer.
The load/pressure table, using “10 km/h loaders" as a reference, is given in international standards
Rear Unladen This table is used when the weight of the rear axle of the unladen loader is known or when the rear axle weight is
given by the manufacturer.
Compactor:
10 and 15 km/h These tables are given according to the maximum work speeds of the compactors. In all cases, the indications and the
instructions provided by the manufacturer must be applied (Table indicating the pressure according to the work to
be carried out).
Transport machines: For underground transport machines, the table corresponds to a maximum speed of 10 km/h.
For different speeds, the load capacity is adapted by applying the coefficients defined by the international standards
(see table TRA 2007 4-25 below).
Maximum speed (km/h) of the machine Variation in load capacity (%)
static + 60
Creep 60m in 30mn + 30
4 + 15
10 0
15 - 13
25 - 20
> 25 #
# Consult the tyre manufacturers.
Skid Steer:
All axles This table which is used when the axle weight has been determined (by weighing or with the manufacturer's data).
Backhoes:
Cyclic This table is used for repeated movements over short distances (600 m maximum) at a maximum speed of 10 km/h.
10 km/h This table is used when the machine has been weighed, front axle bucket full.
20, 30 This table is used when the machine has been weighed, rear axle empty according to the maximum speed
and 40 km/h of the machine.
Excavators:
10, 20, 30 This table is used when the axle weight has been determined (by weighing or with the manufacturer's data).
and 40 km/h
Graders:
All axles This table is used when the axle weight has been determined (by weighing or with the manufacturer's data).
(maximum speed For different speeds, the load capacity will be adapted by applying the coefficients defined
of 40 km/h) by the international standards. (see table TRA 2007 4-27 below).
Speed of use (km/h) Variation in load capacity (%)
40 0
50 -9
60 -18
65 - 27
TECHNICAL DATA EARTHMOVER TYRES
15
CHARACTERISTICS OF MICHELIN EARTHMOVER TYRES
Transport (rigid dump trucks, trucks, …), Articulated dump trucks, Scrapers:
Standard This table is used when the work is carried out at load speeds up to 50 km/h.
This is standardised under the name “Transport 50 km/h”.
For different speeds, the load capacity will be adapted by applying the coefficients
defined by the international standards. (see table ETRTO 2008 E.7 below).
The greyed box indicates the nominal load of the tire.
70 km/h This table is used for the vehicles at speeds of up to 70 km/h (tyres of index speed E).
15"
7.50 R 15 Tube Type
5.5
6.0 - 15/16 J
XLC C1 218 780 254 198 770 338 2324 9 40 6.00S
123461 8,6 30,7 10 7,8 30,3 13,3 91,5 11,3 11 15x6.00
6.5
B6.5
5.5
6.0 - 15/16 J
XMINE D2 L5 6 230 840 385 2550 46 39 6.00S
123342 3,7 9,1 33,1 15,2 100,4 58 10 15x6.00
6.5
B6.5
8.25 R 15 Tube Type
6.0 15 K
XLC C1 -
241 846 281 233 824 374 2493 10 47 6.5
220510 15x7.50
9,5 33,3 11,1 9,2 32,4 14,7 98,1 12,6 12 B6.5
(8) 15x6.00
7.0
6.0 15 K
XMINE D2 L5 6 250 882 402 2680 48 47 6.5 -
15x7.50
123352 3,7 9,8 34,7 15,8 105,5 60,5 12 B6.5 15x6.00
7.0 15x6.00
14.5 R 15 Tubeless
10.50
XMINE D2 L5 6 380 894 408 2711 48 90 11.00BD - -
123101 3,7 15 35,2 16,1 106,7 60,5 24 11.0 -
11.50
400/80 R 15 (38x16 R 15) Tubeless
27x8.50 R 15 Tubeless
16.5"
10 R 16.5 Tubeless
STABIL'X XZSL L3 128A5 25 267 773 350 2335 20 60 - -
8.25
110546 15,5 10,5 30,4 13,8 91,9 25,2 16 -
12 R 16.5 Tubeless
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
10 km/h
6mph 1250 1400 1470 1540 1680 1830 1970 2120 2420 2725
XLC C1 C1 Compactors
15 km/h
7.50 R 15
1020 1135 1190 1250 1375 1500 1600 1700 1980 2180
9 mph
Front laden 1850 2000 2075 2150 2250 2400 2500 2650 2900 3150
XMINE D2 L5 L5 Loaders
Rear unladen 1475 1600 1650 1725 1800 1925 2000 2125 2325 2525
XMINE D2 L5 L5 Underground machines Front and Rear 1675 1800 1875 1925 2025 2150 2250 2375 2600 2825
10 km/h
6mph 1420 1580 1655 1730 1890 2050 2210 2370 2680 3000
XLC C1 C1 Compactors
15 km/h 1260 1400 1470 1540 1690 1830 1970 2110 2360
8.25 R 15
9 mph
Front laden 2000 2200 2300 2400 2550 2700 2850 3000 3300 3600
XMINE D2 L5 L5 Loaders
Rear unladen 1600 1750 1850 1925 2050 2150 2275 2400 2650 2875
XMINE D2 L5 L5 Underground machines Front and Rear 1800 1975 2075 2150 2300 2425 2575 2700 2975 3250
10.00 R 15
Front laden 2400 2600 2800 3000 3200 3350 3500 3700 3900 4300
XMINE D2 L5 L5 Loaders
Rear unladen 1925 2075 2250 2400 2550 2675 2800 2965 3125 3450
XMINE D2 L5 L5 Underground machines Front and Rear 2150 2350 2525 2700 2875 3025 3150 3325 3500 3875
bar 3 3,5 3,75 4 4,5 5 5,5 6 7 8
Utilisation
psi 44 51 54 58 65 73 80 87 102 116
350/65 R 15
Front laden 2400 2660 2790 2920 3150 3400 3570 3750 4200 4600
XMINE D2 L5 L5 Loaders
Rear unladen 1920 2128 2232 2336 2520 2720 2856 3000 3360 3680
XMINE D2 L5 L5 Underground machines Front and Rear 2160 2394 2511 2628 2835 3060 3213 3375 3780 4140
14.5 R 15
Front laden 2550 2850 2975 3100 3350 3600 3850 4100 4600 5100
XMINE D2 L5 L5 Loaders
Rear unladen 2050 2275 2375 2475 2675 2875 3075 3275 3675 4075
XMINE D2 L5 L5 Underground machines Front and Rear 2300 2575 2675 2800 3025 3250 3475 3700 4150 4600
400/80 R 15
Front laden 3300 3650 3825 400 4350 4700 5050 5400 6100 6600
XMINE D2 L5 L5 Loaders
Rear unladen 2650 2925 3050 3200 3475 3750 4050 4325 4875 5275
XMINE D2 L5 L5 Underground machines Front and Rear 2975 3275 3450 3600 3900 4225 4550 4850 5500 5950
bar 1,5 2 2,5 3 3,5 3,75
Utilisation
27x8.50 R 15
psi 22 29 36 44 51 54
STABIL'X XZSL L3 L3 Skid Steers Front and Rear 540 830 920 1100 1225 1285
STABIL'X XZSL L3 L3 Skid Steers Front and Rear 980 1170 1380 1570 1725 1800
12 R 16.5
STABIL'X XZSL L3 L3 Skid Steers Front and Rear 1425 1675 1875 2200 2450 2575
TECHNICAL DATA EARTHMOVER TYRES
18
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
18"
280/80 R 18 Tubeless
W8 - KLEBER 438
XMCL 132A8/130B 282 905 389 290 908 415 2708 28 90 W9
779803 11,1 35,6 15,3 11,4 35,7 16,3 106,6 35,3 24 W10 -
DW10
W10 - KLEBER 444
XZSL 151A2/139B 356 1015 345 995 445 2995 26 123 W10L
122999 14 40 13,6 39,2 17,5 117,9 32,8 32 W11 -
DW11
340/80 R 18 Tubeless
W10
11 SDC
XMCL 143A8/143B 343 1001 462 351 996 448 2959 30 141 11.00 - K057866
100054 13,5 39,4 18,2 13,8 39,2 17,6 116,5 37,8 37 W11 -
12 SDC
12
19.5"
18 R 19.5 Tubeless
20"
9.00 R 20 Tube Type
6.5 - B6.5
7.0T
7.0 -
XMINE D2 L5R * 6 277 1054 484 3203 51 98 20 M
B 7.0 A20
123382 3,7 10,9 41,5 19,1 126,1 64,3 26 7.33V 20x7.50
553004
B7.5
7.5
280/80 R 20 Tubeless
W8 - K171111
XMCL 133A8/133B 282 956 389 292 958 439 2860 29 97 W9
747442 11,1 37,6 15,3 11,5 37,7 17,3 112,6 36,5 26 W10 -
8.0
8.5
8.5V - 20 Q
XMINE D2 L5R 6 323 1174 535 3558 57 146 B 8.5
123392 3,7 12,7 46,2 21,1 140,1 71,8 39 8.50V 20x8.50
9.00V
9.0
TECHNICAL DATA EARTHMOVER TYRES
19
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
280/80 R 18
Cyclic 1170 1430 1700 1960 2220 2480 2740 3000
XMCL Backhoe loaders 30 km/h 1020 1210 1400 1580 1770 1950 2140
19mph
40 km/h 950 1120 1300 1475 1650 1825 2000
25mph
bar 1 1,6 1,9 2,7 3 3,2 3,5 3,8
Utilisation
psi 15 23 28 39 44 46 51 55
10 km/h
1510 1930 2130 2690 2900 3030 3240 3450
335/80 R 18
6mph
30 km/h 1210 1540 1710 2150 2320 2430 2590 2760
XZSL Backhoe loaders 19mph
40 km/h 1100 1410 1560 1960 2110 2220 2370 2520
25mph
50 km/h 1060 1360 1500 1890 2040 2140 2280 2430
31mph
bar 1,6 2 2,4 2,8 3,2 3,6 4 4,4
Utilisation
psi 23 29 35 41 46 52 58 64
340/80 R 18
Static 2450 3000 3540 4090 4630 5180 5720 6270
Cyclic 1600 1950 2310 2670 3020 3380 3730 4090
XMCL Backhoe loaders 30 km/h 1390 1650 1900 2160 2410 2660 2920
19mph
40 km/h 1320 1550 1780 2010 2240 2580 2725
25mph
10 km/h
6mph 3875 4170 4465 4760 5055 5345 5640 5935 6230 6525
18 R 19.5
20 km/h 3285 3570 3855 4140 4425 4710 4995 5280 5565 5850
XF * Wheeled Excavators 12mph
30 km/h 2835 3120 3405 3690 3975 4260 4545 4830 5115 5400
19mph
40 km/h 2115 2380 2645 2910 3175 3440 3705 3970 4235 4500
25mph
bar 3 4 5 6 7 8
Utilisation
20" psi 44 58 73 87 102 116
XMINE D2 * L5R L5R Underground machines Front and Rear 2700 3050 3400 3800 4150 4500
XMINE D2 L5R L5R Loaders Front laden 3400 4000 4600 5200 5800 6400
Rear unladen 2700 3200 3700 4150 4650 5100
XMINE D2 L5R L5R Underground machines Front and Rear 3050 3600 4150 4700 5200 5750
TECHNICAL DATA EARTHMOVER TYRES
20
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
20"
E20 Pilote (13/80 R 20) Tube Type
7.33V - 7.5
B 7.5 - 8.0
B8.0 - 8.0V
XLC C1 352 1069 391 322 1050 470 3160 12 140 8.00V - 8.5 B - 20 P
240750 13,9 42,1 15,4 12,7 41,3 18,5 124,4 15,1 37 B8.5 - 8.50V 20x8.50
9.00V - 10.0
- 10.00V
9.0
335/80 R 20 Tubeless
-
W10 KLEBER 444
XZSL 153A2/141B 356 1066 337 1068 476 3209 25 OR 6.6-20
11 SDC
792581 14 42 13,3 42 18,7 126,3 31,5 (R1681) -
11DC
553215
340/80 R 20 Tubeless
W10
11 SDC
XMCL 144A8/144B 343 1052 462 353 1047 476 3119 29 152 11.00 - KLEBER 664
948730 13,5 41,4 18,2 13,9 41,2 18,7 122,8 36,5 40 W11 -
12 SDC
12
14.00 R 20 Tubeless
375/75 R 20 Tubeless
-
W10 KLEBER 664
XZSL 155A2/143B 396 1092 395 1067 481 3219 29 162 OR 6.6-20
11 SDC
122989 15,6 43 15,6 42 18,9 126,7 36,5 43 (R1681) -
11DC
553215
380/75 R 20 Tubeless
11.0
XMCL 148A8/148B 380 1078 507 384 1072 481 3199 33 181 W11 - KLEBER 664
187752 15 42,4 20 15,1 42,2 18,9 125,9 41,6 48 12 -
W12
400/70 R 20 Tubeless
12
12 SDC - KLEBER 664
XMCL 149A8/149B 404 1068 536 412 1069 481 3177 33 187 13.00
474495 15,9 42 21,1 16,2 42,1 18,9 125,1 41,6 49 -
13SDC
14
405/70 R 20 Tubeless
W10
11DC -
XZSL 155A2/143B 452 1121 409 1102 492 3314 30 202 11 SDC KLEBER 664
OR 6.6-20
753584 17,8 44,1 16,1 43,4 19,4 130,5 37,8 53 12 DC (R1681) -
13 SDC 553215
13 DC
TECHNICAL DATA EARTHMOVER TYRES
21
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 3 4 5 6 7 8 8,5 9
Utilisation
20" psi 44 58 73 87 102 116 123 131
10 km/h
2520 3100 3660 4260 4840 5420 5710 6000
E20 Pilote
6mph
XLC C1 C1 Compactors
15 km/h 2240 2760 3260 3790 4310 4820 5000
9 mph
335/80 R 20
6mph
30 km/h 1280 1630 1810 2280 2450 2570 2740 2920
XZSL Backhoe loaders 19mph
40 km/h 1170 1490 1650 2080 2240 2340 2500 2660
25mph
50 km/h 1130 1440 1590 2010 2160 2260 2420 2575
31mph
bar 1,6 2 2,4 2,8 3,2 3,6 4 4,4
Utilisation
psi 23 29 35 41 46 52 58 64
340/80 R 20
Static 2520 3080 3640 4200 4760 5320 5880 6440
Cyclic 1640 2005 2370 2740 3105 3470 3835 4200
XMCL Backhoe loaders 30 km/h 1430 1690 1950 2210 2470 2735 3000
19mph
40 km/h 1360 1595 1830 2065 2300 2550 2800
25mph
bar 3 4 5 5,5 6 6,5 7 8 8,5
Utilisation
psi 44 58 73 80 87 94 102 116 123
14.00 R 20
Front laden 4140 4920 5690 6070 6460 6850 7230 8010
XMINE D2 L5R L5R Loaders
Rear unladen 2430 3100 3770 4100 4430 4770 5100 5770
XMINE D2 L5R L5R Underground machines Front and Rear 3480 4200 4920 5280 5640 6000 6360 7070 7793
bar 1 1,6 1,9 2,7 3 3,2 3,5 3,8
Utilisation
psi 15 23 28 39 44 46 51 55
10 km/h
1700 2160 2400 3020 3250 3410 3640 3880
375/75 R 20
6mph
30 km/h 1360 1730 1920 2420 2600 2730 2910 3100
XZSL Backhoe loaders 19mph
40 km/h 1240 1580 1750 2200 2370 2490 2660 2830
25mph
50 km/h 1190 1520 1690 2120 2290 2400 2560 2725
31mph
bar 1,6 2 2,4 2,8 3,2 3,6 4 4,4
Utilisation
psi 23 29 35 41 46 52 58 64
380/75 R 20
psi 23 29 35 41 46 52 55 58 64
Static 2930 3580 4230 4880 5530 6180 6505 6830 7480
Cyclic 1910 2330 2760 3180 3600 4030 4240 4450 4880
XMCL Backhoe loaders 30 km/h 1660 1960 2270 2570 2870 3180 3330 3480
19mph
40 km/h 1550 1825 2100 2375 2650 2950 3100 3250
25mph
bar 1 1,6 1,9 2,7 3 3,2 3,5 3,8
Utilisation
psi 15 23 28 39 44 46 51 55
10 km/h
6mph 1700 2160 2400 3020 3250 3410 3640 3880
405/70 R 20
20"
16.00 R 20 Tubeless
-
XZL E2 173G 70 466 1381 438 1343 615 4080 27 315 10.00W 20 V
123357 43,5 18,3 54,4 17,2 52,9 24,2 160,6 34 83 11.25 A20 20x10.00
553004
420/75 R 20 Tubeless
12 SDC
12 - KLEBER 829
XMCL 154A8/154B 418 1138 552 428 1138 509 3378 33 229 13 SDC
967201 16,5 44,8 21,7 16,9 44,8 20 133 41,6 61 -
13.00
14
425/75 R 20 Tubeless
11DC
11SDC -
W11 KLEBER 829
XZSL 167A2/155B 442 1172 434 1142 488 3390 29 240 OR 6.6-20
DW11
122979 17,4 46,1 17,1 45 19,2 133,5 36,5 63 (R1681) -
13SDC
13 DC 553215
W13
20.5"
525/65 R 20.5 Tubeless
24 R 20.5 Tubeless
21"
24 R 21 Tubeless
-
XZL E2 176G 608 1388 631 4200 21 WAM
18.00/1.5 OR 6.6-21
110257 23,9 54,6 24,8 165,4 17-20
553213
TECHNICAL DATA EARTHMOVER TYRES
23
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 2 3 4 5 6 7 8 8,5 9 10
Utilisation
20" psi 29 44 58 73 87 102 116 123 131 145
0 km/h
0mph 3580 4830 6125 7390 8660 9900 11200 12075 12950 14700
5 km/h 2850 3950 5000 6100 7200 8100 9250 9825 10400 11550
3mph
10 km/h 2750 3750 4750 5750 6700 7600 8700 9125 9550 10600
6mph
20 km/h 2500 3250 4250 5000 6000 6860 7600 8075 8550 9500
12mph
16.00 R 20
30 km/h 2250 3000 3750 4500 5250 6000 6860 7225 7590
XZL E2 E2 Cranes 19mph
40 km/h 2000 2750 3550 4250 5000 5750 6500 6830 7160
25mph
50 km/h 1950 2700 3500 4200 4900 5700 6350 6725 7100
31mph
65 km/h 1850 2650 3400 4150 4850 5550 6300 6650 7000
40mph
80 km/h 1800 2600 3350 4100 4800 5500 6250 6550 6850
50mph
90 km/h 1750 2550 3300 4050 4750 5450 6200 6500
56 mph
bar 1,6 2 2,4 2,8 3,2 3,6 4 4,4
Utilisation
psi 23 29 35 41 46 52 58 64
420/75 R 20
Static 3380 4130 4880 5630 6380 7130 7880 8630
Cyclic 2200 2690 3180 3670 4160 4650 5140 5630
XMCL Backhoe loaders 30 km/h 1920 2270 2620 2960 3310 3660 4010
19mph
40 km/h 1800 2120 2440 2755 3075 3410 3750
25mph
bar 1 1,6 1,9 2,7 3 3,2 3,5 3,8
Utilisation
psi 15 23 28 39 44 46 51 55
10 km/h
2390 3040 3370 4250 4570 4790 5120 5450
425/75 R 20
6mph
30 km/h 1910 2430 2700 3400 3660 3830 4100 4360
XZSL Backhoe loaders 19mph
40 km/h 1740 2220 2460 3100 3340 3500 3740 3980
25mph
50 km/h 1700 2160 2400 3020 3250 3410 3640 3875
31mph
bar 1 2 3 4 5 6 7 8
Utilisation
20.5" psi 15 29 44 58 73 87 102 116
525/65 R 20.5
Road in single 1450 2150 2850 3600 4300 5000 5750 6500
XS E7 E7 Desert conditions 80 km/h max. Track in single 1700 2600 3500 4450 5250
Sand in single 2300 3850 5250
bar 1 2 2,5 3 3,5 4 4,5 5 5,5 6
Utilisation
psi 15 29 36 44 51 58 65 73 80 87
24 R 20.5
Road in single 1950 2950 3450 4000 4500 5010 5520 6050 6575 7100
XS E7 E7 Desert conditions 80 km/h max. Track in single 2550 3650 4250 4750 5300 5850 6400 6750 7100
Sand in single 3500 5350 6400 7100
Road in single 1950 2950 3450 4000 4500 5010 5520 6050 6575 7100
24 R 21
XZL E2 E2 Desert conditions 80 km/h max. Track in single 2550 3650 4250 4750 5300 5850 6400 6750 7100
Sand in single 3500 5350 6400
TECHNICAL DATA EARTHMOVER TYRES
24
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
22.5"
15 R 22.5 Tubeless
XF * - 20 S
430 1132 387 1108 503 3353 25 200
255205 11.75
(8) 16,9 44,6 15,2 43,6 19,8 132 31,5 53 -
18 R 22.5 Tubeless
22.5 TAMD
XF * 507 1224 453 1188 543 3604 25 255 -
14.00 22.5 TD
255300 20 48,2 17,8 46,8 21,4 141,9 31,5 67
-
24"
12.00 R 24 Tube Type
7.33V
8.00V - 24 Q
XZH E3 *** 35 119 340 1285 378 321 1258 591 3857 30 171 8.0
123369 21,7 82 13,4 50,6 14,9 12,6 49,5 23,3 151,9 37,8 45 24/25x8.50
8.5
8.50V
13.00 R 24 Tubeless
-
XGL A2 L2 * TG 8.00 TG SDC KLEBER 703
16 360 1318 335 1296 570 3875 25 215 OR 2-25
123386 9.00/1.5 DC
(6, 10) 9,9 14,2 51,9 13,2 51 22,4 152,6 31,5 57 10.00 VA SDC HEUPO 13-24 DR
553201
TECHNICAL DATA EARTHMOVER TYRES
25
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
10 km/h
6mph 3660 3875 4085 4290 4510 4720 4935 5150
15 R 22.5
20 km/h 3130 3350 3560 3770 3990 4200 4410 4620
XF * Wheeled Excavators 12mph
30 km/h 2755 2970 3190 3400 3620 3830 4050 4265
19mph
40 km/h 2055 2270 2480 2695 2910 3125 3335 3550
25mph
bar 3 3,5 4 4,5 5 5,5 6 6,5 7 7,5
Utilisation
psi 44 51 58 65 73 80 87 94 102 109
10 km/h
4290 4575 4860 5150 5440 5725 6015 6300 6590 6875
18 R 22.5
6mph
20 km/h 3485 3770 4055 4340 4625 4910 5195 5480 5765 6050
XF * Wheeled Excavators 12mph
30 km/h 3035 3320 3605 3890 4175 4460 4745 5030 5315 5600
19mph
40 km/h 2045 2330 2620 2905 3190 3480 3765 4050 4340 4625
25mph
XZH *** E3 E3 Transport Standard 2700 2950 3200 3475 3750 4000 4250 4500 4650
12.00 R 24
bar 2 2,5 3 3,5 4 4,5 5 5,5 6 7
Utilisation
psi 29 36 44 51 58 65 73 80 87 102
Front tip.load 3900 4600 5200 5850 6550 7150 7800 8450 9100 10350
XSM D2+ L5S L5S Loaders Front laden 2300 2700 3050 3450 3850 4200 4600 4975 5350 6100
XMINE D2 L5R L5R
Rear unladen 1850 2150 2450 2750 3100 3350 3700 4000 4300 4900
XK A *** L3 L3
XSM D2+ L5S L5S Underground machines Front and Rear 2050 2450 2750 3100 3450 3800 4150 4475 4800 5500
XMINE D2 L5R L5R
13.00 R 24
XGL A2 * TG L2 L2 Loaders Front laden 2650 3100 3600 4050 4500 4950 5400
Rear unladen 2100 2500 2900 3250 3600 3950 4300
XGL A2 * TG L2 L2 Graders Front and Rear 1900 2225 2550 2900
TECHNICAL DATA EARTHMOVER TYRES
26
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
24"
14.00 R 24 Tube Type
9.00V
XL C C C1 400 1365 444 369 1336 603 4034 18 275 9.0 - 24/25 T
251930 15,7 53,7 17,5 14,5 52,6 23,7 158,8 22,7 73 10.0/2.0 13-24/25
10.00W
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
10 km/h
6mph 3500 4600 5690 6520 7340 7610 7880 8980 9520 10075
XL C C C1 C1 Compactors
15 km/h 3120 4090 5060 5760 6450
9 mph
bar 1 2 2,5 3 3,5 4 4,5 5 6 7
Utilisation
psi 15 29 36 44 51 58 65 73 87 102
Road in single 950 1600 1950 2300 2650 3000 3350 3650 4300 5000
Track in single 1100 1900 2300 2700 3100 3500 3900 4300
Sand in single 2250 3800 4300
XS E7 E7 Desert conditions 80 km/h max.
Road in twin 855 1440 1755 2070 2385 2700 3015 3285 3870 4500
Track in twin 990 1710 2070 2430 2790 3150 3510 3870
Sand in twin 2025 3420 3870
bar 4 5 5,5 6 6,5 7 8
Utilisation
psi 58 73 80 87 94 102 116
14.00 R 24
XK D1 A *** E4 E4
Front tip.load 5550 6400 7300 8150 9100 10050 10900 11750
XSNOPLUS * TG L2 L2 Loaders Front laden 3250 3750 4300 4800 5350 5900 6400 6900
XGL A2 * TG L2 L2
Rear unladen 2600 3000 3450 3850 4300 4700 5100 5500
XSNOPLUS * TG L2 L2
L2 Graders Front and Rear 2300 2725 3125 3550
XGL A2 * TG L2
TECHNICAL DATA EARTHMOVER TYRES
28
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
24"
385/95 R 24 Tube Type
10.00W - 24/25 T
X-CRANE AT 170F 80 409 1415 455 376 1361 632 4153 23 284 10.0
778245 49,7 16,1 55,7 17,9 14,8 53,6 24,9 163,5 29 75 13-24/25
11.25/1.3
16.00 R 24 Tubeless
XR B E3 - 24/25 VAM
35 204 480 1561 513 426 1482 672 4482 26 380
260436 11.25/2.5
(8) 21,7 140 18,9 61,5 20,2 16,8 58,3 26,5 176,5 32,8 100 14-24/25
16.00 R 24 Tubeless
-
XGL A2 L2 * TG 24/25 VD
16 474 1527 435 1500 651 4464 27 412 OR 2-25
123903 10.00 VA SDC
(6) 9,9 18,7 60,1 17,1 59,1 25,6 175,7 34 109 HEUPO 13-24 DR
553201
TECHNICAL DATA EARTHMOVER TYRES
29
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 5 6 7 8 9
Utilisation
24" psi 73 87 102 116 131
0 km/h
0mph 10250 11900 13500 15200 16200
5 km/h 7980 9135 10290 11445 12600
3mph
10 km/h 6840 7830 8820 9810 10800
6mph
15 km/h 6270 7180 8085 8995 9900
9 mph
20 km/h 5700 6525 7350 8175 9000
12mph
25 km/h 5130 5875 6615 7360 8100
15 mph
30 km/h
30 km/h
19mph 4860 5880 6460 7000 7800
40 km/h 4635 5610 6165 6675 7450
25mph
50 km/h 4410 5340 5865 6355 7100
31mph
385/95 R 24
65 km/h
XMH S E2T E2T 4020 4865 5345 5790 6450
Cranes 40mph
XSNOPLUS E2 E2 70 km/h 3740 4525 4970 538 6000
43mph
80 km/h 3086 3735 4100 4445 4950
50mph
90 km/h 2620 3170 3480 3770 4200
56 mph
100 km/h 2245 2715 2980 3230 3600
62 mph
bar 3 4 5 6 6,5 7 7,5 8 8,5
Utilisation
psi 44 58 73 87 94 102 109 116 123
15.00 R 24
10 km/h
6mph 5320 6540 7750 8965 9570 10180 10790 11390 12000
XLC C1 C1 Compactors 15 km/h 4740 5820 6900 7980 8520
9 mph
bar 4 4,5 5 5,5 6 6,5 7 8 8,5
Utilisation
psi 58 65 73 80 87 94 102 116 123
XR B E3 E3 Transport Standard 5000 5450 5900 6400 6850 7300 7550 8000 8250
16.00 R 24
24"
440/80 R 24 Tubeless
460/70 R 24 Tubeless
DW14L
14.00 - KLEBER 710
XMCL 159A8/159B 455 1254 609 467 1248 562 3709 36 291 DW15L
244268 17,9 49,4 24 18,4 49,1 22,1 146 45,4 77 -
16.00
DW16L
500/70 R 24 Tubeless
25"
13.00 R 25 Tubeless
-
XR B E3 *** 24/25 T
35 137 379 1342 421 335 1304 603 3973 22 215 8.50/1.3 OR 2-25
243320 21,7 94 14,9 52,8 16,6 13,2 51,3 23,7 156,4 27,7 57 10.00/1.5 HEUPO 24/25x8.50
(8)
553201
14.00 R 25 Tubeless
XMH E2T *** 50 232 409 1415 389 1361 634 4158 24 278
235951 31,1 159 16,1 55,7 15,3 53,6 25 163,7 30,2 73 - 24/25 TAM
XH D1 A E4 *** 22 102 650 4291 24/25 T
450 10.00/1.5 OR 2-25
123331 13,7 70 25,6 168,9
405 1467 17,7 380 1410 38 265 11.25/1.3 HEUPO 13-24/25
XH D1 A4 E4 *** 15,9 57,8 15 55,5 47,9 70
123545 18 84 649 4288 553201 13-24/25 S
(8) 11,2 58 25,6 168,8
385/95 R 25 Tubeless
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
440/80 R 24
Cyclic 2710 3320 3920 4520 5130 5730 6330 6940
XMCL Backhoe loaders 30 km/h 2370 2800 3230 3660 4090 4520 4950
19mph
40 km/h 2240 2650 3060 3465 3875 4250 4625
25mph
460/70 R 24
Cyclic 2570 3140 3710 4280 4850 5420 5990 6560
XMCL Backhoe loaders 30 km/h 2240 2650 3050 3460 3870 4270 4680
19mph
40 km/h 2120 2500 2885 3270 3650 4010 4375
25mph
500/70 R 24 - 164A8/164B
Static 4500 5500 6500 7500 8500 9500 10500 11500
Cyclic 2930 3590 4240 4890 5540 6200 6850 7500
XMCL Backhoe loaders 30 km/h 2560 3020 3490 3950 4420 4880 5350
19mph
40 km/h 2360 2800 3210 3685 4125 4560 5000
25mph
13.00 R 25
XR B *** E3 E3 Transport Standard 3150 3450 3800 4100 4300 4450 4875 5400
14.00 R 25
XMH *** E2T E2T
XH D1 A *** E4 E4 Transport Standard 3750 4100 4500 4850 5100 5250 5800 6350
XH D1 A4 *** E4 E4
bar 5 6 7 8 9
Utilisation
psi 73 87 102 116 131
30 km/h
19mph 4860 5880 6460 7000 7800
40 km/h 4635 5610 6165 6675 7450
25mph
385/95 R 25 170E
25"
385/95 R 25 Tubeless
-
OR 3-25 SULLA 24/25 TAM
9.50/1.7 CR 553200 24/25 T
X-CRANE AT 170F 80 409 1415 455 380 1365 634 4168 23 280 10.00/1.5
296917 49,7 16,1 55,7 17,9 15 53,7 25 164,1 29 74 13-24/25
11.25/1.3 OR 2-25 13-24/25 S
HEUPO
553201
15.5 R 25 Tubeless
395/80 R 25 Tubeless
-
XMP E3P 165E 50 180 434 1317 469 403 1270 579 3849 24 278 11.25/1.3 25 SAM
OR 2-25
123409 31,1 123 17,1 51,9 18,5 15,9 50 22,8 151,5 30,2 73 12.00/1.3 HEUPO 15-24/25
553201
16.00 R 25 Tubeless
-
XL B E2 177E 70 483 1549 518 422 1484 681 4509 29 350 11.00/1.7 CR 24/25 VAM
123481 43,5 19 61 20,4 16,6 58,4 26,8 177,5 36,5 92 11.25/2 OR 3-25 SULLA 14-24/25
553200
TECHNICAL DATA EARTHMOVER TYRES
33
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 5 6 7 8 9
Utilisation
25" psi 73 87 102 116 131
0 km/h
0mph 10250 11900 13500 15200 16200
5 km/h 7980 9135 10290 11445 12600
3mph
10 km/h 6840 7830 8820 9810 10800
6mph
15 km/h 6270 7180 8085 8995 9900
9 mph
20 km/h 5700 6525 7350 8175 9000
12mph
25 km/h 5130 5875 6615 7360 8100
15 mph
15.5 R 25
XMINE D2 * L5R L5R
Rear unladen 2950 3400 3850 4300 4650 5150
XMINE D2 * L5R L5R Underground machines Front and Rear 3350 3850 4300 4800 5200 5800
XTL A * L2 L2
XH A * L3 L3 Graders Front and Rear 2325 2650 3000
XMINE D2 * L5R L5R
bar 4 4,5 5 5,5 6 6,5 7
Utilisation
psi 58 65 73 80 87 94 102 395/80 R 25
XMP E3P E3P Transport Standard 3850 4150 4500 4650 4850 5000 5150
bar 2 3 4 5 6 7 8 9 10
Utilisation
psi 29 44 58 73 87 102 116 131 145
0 km/h
0mph 7200 9300 11300 13400 15400 17400 19400 20700 22600
5 km/h 5100 6550 7950 9450 10800 12300 13700 16700
3mph
10 km/h 4500 5800 7050 8350 9600 10900 12150 13400
6mph
20 km/h 3350 4450 5400 6400 7350 8300 9300 10250
16.00 R 25 - 445/95 R 25
12mph
30 km/h 2925 4100 5000 5850 6750 7650 8600 9500
19mph
40 km/h 2800 3900 4775 5600 6450 7300 8200 9050
XL B E2 E2 Cranes 25mph
50 km/h 2650 3725 4550 5300 6150 6950 7800 8600
31mph
65 km/h 2400 3375 4125 4850 5600 6350 7150 7800
40mph
70 km/h 2250 3150 3850 4500 5200 5900 6600 7300
43mph
80 km/h 1850 2600 3150 3700 4250 4850 5400 6000
50mph
90 km/h 1575 2200 2700 3150 3650 4150 4600 5100
56 mph
100 km/h 1350 1900 2300 2700 3120 3550 3950 4400
62 mph
TECHNICAL DATA EARTHMOVER TYRES
34
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
16.00 R 25 Tubeless
XR B E3 ** 35 204 426 1482 677 4495 26 350
261022 21,7 140 16,8 58,3 26,7 177 32,8 92
(8) 1561
61,5
XK B E3 ** 32 187 460 1502 688 4560 27
261110 19,9 128 18,1 59,1 27,1 179,5 34 -
XH D1 A4 E4 ** 480 518 11.25/2.0 24/25 VAM
18 105 1520 687 4658 43 OR 3-25 SULLA
123489 18,9 20,4 13.00/2.0 14-24/25
(8) 11,2 72 1623 462 59,8 27 183,4 54,2 380 553200
63,9 18,2 100
XH D1 A E4 ** 28 164 1540 696 4652 47
123350 17,4 112 60,6 27,4 183,1 59,2
X-QUARRY E4R ** 16 93 1561 437 1542 707 4683 48
692021 9,9 64 61,5 17,2 60,7 27,8 184,4 60,5
16.00 R 25 Tubeless
445/95 R 25 Tubeless
-
X-CRANE AT 174F 80 483 1549 518 442 1485 690 4532 25 380 11.00/1.7 CR 24/25 VAM
297069 49,7 19 61 20,4 17,4 58,5 27,2 178,4 31,5 100 11.25/2 OR 3-25 SULLA 14-24/25
553200
445/95 R 25 Tubeless
-
XSNOPLUS E2 177E 70 483 1549 518 447 1486 690 4535 25 380 11.00/1.7 CR 24/25 VAM
123857 43,5 19 61 20,4 17,6 58,5 27,2 178,5 31,5 100 11.25/2 OR 3-25 SULLA 14-24/25
553200
TECHNICAL DATA EARTHMOVER TYRES
35
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XR B ** E3 E3
XK B ** E3 E3 Transport Standard 5000 5450 5900 6400 6850 7300 7550 7750 8000
XH D1 A4 ** E4 E4
XH D1 A ** E4 E4
E4R 30 km/h
X-QUARRY ** E4R Quarry transport 5300 5800 6300 6800 7300 7800
19mph
16.00 R 25
bar 2 3 4 5 6 7
Utilisation
psi 29 44 58 73 87 102
Front tip.load 7650 9850 12000 14200 16300 18550
XMINE D2 L5R L5R Loaders Front laden 4500 5800 7050 8350 9600 10900
Rear unladen 3600 4650 5650 6700 7700 8700
XK A ** L3 L3
L5R Underground machines Front and Rear 4050 5200 6350 7500 8650 9800
XMINE D2 L5R
bar 5 6 7 8 9
Utilisation
psi 73 87 102 116 131
0 km/h
0mph 10675 12190 13700 15225 16750
5 km/h 8965 10240 11510 12780 14070
3mph
10 km/h 7685 8775 9665 10960 12060
6mph
12mph
30 km/h 2925 4100 5000 5850 6750 7650 8600 9500
19mph
40 km/h 2800 3900 4775 5600 6450 7300 8200 9050
XSNOPLUS E2 E2 Cranes 25mph
50 km/h 2650 3725 4550 5300 6150 6950 7800 8600
31mph
65 km/h 2400 3375 4125 4850 5600 6350 7150 7800
40mph
70 km/h 2250 3150 3850 4500 5200 5900 6600 7300
43mph
80 km/h 1850 2600 3150 3700 4250 4850 5400 6000
50mph
90 km/h 1575 2200 2700 3150 3650 4150 4600 5100
56 mph
100 km/h 1350 1900 2300 2700 3120 3550 3950 4400
62 mph
TECHNICAL DATA EARTHMOVER TYRES
36
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
17.5 R 25 Tubeless
17.5 R 25 Tubeless
445/80 R 25 Tubeless
-
OR 3-25 SULLA
XG C E2 170E 70 494 1404 534 438 1358 622 4123 28 340 14.00/1.5 553200 24/25 TAM
264520 43,5 19,4 55,3 21 17,2 53,5 24,5 162,3 35,3 90 14.00/1.7 CR 16-24/25
OR 2-25
HEUPO
553201
TECHNICAL DATA EARTHMOVER TYRES
37
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 2 3 4 5 6 7 8 9 10
Utilisation
25" psi 29 44 58 73 87 102 116 131 145
0 km/h
0mph 7300 9100 10900 12700 14300 16000
5 km/h 5150 6450 7700 9000 10200 11400
3mph
10 km/h 4550 5700 6800 7950 9000 10050
6mph
20 km/h 3300 4250 5150 6100 7050 7950
12mph
17.5 R 25 - 445/80 R 25
30 km/h 2725 3650 4600 5650 6750 7800
19mph
40 km/h
XL B E2 E2 2600 3475 4400 5400 6450 7450
Cranes 25mph
XG C E2 E2 50 km/h 2475 3300 4150 5150 6150 7100
31mph
65 km/h 2250 3000 3800 4650 5550 6450
40mph
70 km/h 2100 2800 3550 4350 5200 6000
43mph
80 km/h 1725 2300 2900 3600 4250 4950
50mph
90 km/h 1475 1975 2500 3050 3650 4200
56 mph
100 km/h 1250 1675 2150 2650 3150 3600
62 mph
bar 2 2,5 3 3,5 4 4,25 4,5
Utilisation
psi 29 36 44 51 58 62 65
XK A ** L3 L3
XSNOPLUS * TG L2T L2T Front tip.load 7300 8150 9100 10000 10900 11350 11750
XTL A * L2 L2
XH A * L3 L3 Loaders Front laden 4550 5100 5700 6250 6800 7100 7350
XR D1 A * L4R L4R
XLD D2 A * L5T L5T
XMINE D2 L5R L5R Rear unladen 3650 4100 4550 5000 5450 5700 5900
17.5 R 25
XSM D2+ L5S L5S
XK A ** L3 L3
XLD D2 A * L5T L5T Underground machines Front and Rear 4100 4600 5150 5650 6100 6400 6600
XMINE D2 L5R L5R
XSM D2+ L5S L5S
XSNOPLUS * TG L2T L2T
XTL A * L2 L2
XH A * L3 L3 Graders Front and Rear 2800 3250 3650
XR D1 A * L4R L4R
XLD D2 A * L5T L5T
bar 2 3 4 5 6 7
Utilisation
psi 29 44 58 73 87 102
0 km/h
0mph 7300 9100 10900 12700 14300 16000
5 km/h 5150 6450 7700 9000 10200 11400
3mph
10 km/h 4550 5700 6800 7950 9000 10050
6mph
20 km/h 3300 4250 5150 6100 7050 7950
445/80 R 25 - 17.5 R 25
12mph
30 km/h 2725 3650 4600 5650 6750 7800
19mph
40 km/h 2600 3475 4400 5400 6450 7450
XG C E2 E2 Cranes 25mph
50 km/h 2475 3300 4150 5150 6150 7100
31mph
65 km/h 2250 3000 3800 4650 5550 6450
40mph
70 km/h 2100 2800 3550 4350 5200 6000
43mph
80 km/h 1725 2300 2900 3600 4250 4950
50mph
90 km/h 1475 1975 2500 3050 3650 4200
56 mph
100 km/h 1250 1675 2150 2650 3150 3600
62 mph
TECHNICAL DATA EARTHMOVER TYRES
38
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
18.00 R 25 Tubeless
-
XS E7 553 1693 598 492 1600 722 4831 21 532 13.00/2.5 25 WAM
276450 21,8 66,7 23,5 19,4 63 28,4 190,2 26,5 141 15.00/2.5 OR 3-25 SULLA 16-24/25
553200
18.00 R 25 Tubeless
XR B E3 ** 35 259 493 1610 722 4849 28 545
270522 21,7 177 19,4 63,4 28,4 190,9 35,3 144
(8) 1693
XK B E3 ** 66,7
32 237 533 1630 736 4921 30
270630
(8) 19,9 162 21 64,2 29 193,7 37,8
XH D1 B E4 ** 30 222
123021 18,6 152
500 -
XH D1 A E4 ** 132 25 WAM
22 163 553 598 13.00/2.5
123031 525 762 5058 OR 3-25 SULLA
13,7 112 21,8 23,5 15.00/2.5 16-24/25
(8) 20,7 30 199,1 553200
XH D1 A4 E4 ** 18 133 1758 1668 47
123479
(8) 11,2 91 69,2 65,7 59,2
XK D1 B E4 ** 26 192
270660
(8) 16,2 132 530 764 5064 495
20,9 30,1 199,4 131
XK D1 A E4 ** 18 133
270680 11,2 91
18.00 R 25 Tubeless
18.00 R 25 Tubeless
XV C E2 183E -
50 284 551 1672 598 498 1610 743 4901 26 576 13.00/2.5 25 WAM
123993 OR 3-25 SULLA
31,1 195 21,7 65,8 23,5 19,6 63,4 29,3 193 32,8 152 15.00/2.5 16-24/25
(7) 553200
TECHNICAL DATA EARTHMOVER TYRES
39
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
Road in single 3250 3900 4500 5050 5600 6250 6850 8000
Track in single 3250 4050 4950 5750 6600
XS E7 E7 Desert conditions 65 km/h max. Sand in single 3600 5050 6350
Road in twin 2925 3510 4050 4545 5040 5625 6165 7200
Track in twin 2925 3645 4455 5175 5940
Sand in twin 3240 4545 5715
bar 4 4,25 4,5 5 6 7 7,5
Utilisation
psi 58 62 65 73 87 102 109
XR B ** E3 E3
XK B ** E3 E3
XH D1 B ** E4 E4
18.00 R 25
XK D1 B ** E4 E4 Transport Standard 6800 7100 7400 8000 9250 9850 10150
XH D1 A ** E4 E4
XH D1 A4 ** E4 E4
XK D1 A ** E4 E4
12mph
30 km/h 2730 3965 5200 6435 7670 8900 9520 10140 11375
19mph
40 km/h 2605 3782 4960 6140 7315 8500 9085 9670 10850
XV C E2 E2 Cranes 25mph
50 km/h 2480 3600 4720 5840 6960 8085 8695 9205 10325
31mph
65 km/h 2225 3235 4240 5245 6255 7260 7765 8270 9275
40mph
70 km/h 2100 3050 4000 4950 5900 6850 7325 7800 8750
43mph
80 km/h 1720 2500 3280 4060 4840 5615 6000 6390 7175
50mph
90 km/h 1470 2135 2800 3465 4130 4795 5125 5460 6125
56 mph
100 km/h 1260 1830 2400 2970 3540 4110 4395 4680 5250
62 mph
XV C E2 E2 Transport Standard 6800 8000 9250 9850 10150
TECHNICAL DATA EARTHMOVER TYRES
40
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
18.00 R 25 Tubeless
XV C E2 186E -
50 284 551 1672 598 496 1622 743 4925 26 563 13.00/2.5 25 WAM
123491 OR 3-25 SULLA
31,1 195 21,7 65,8 23,5 19,5 63,9 29,3 193,9 32,8 149 15.00/2.5 16-24/25
(8) 553200
505/95 R 25 Tubeless
10.0/2.0 -
XV C E2 183E 50 284 551 1672 587 498 1610 742 4922 26 576 25 WAM
13.00/2.5 OR 3-25 SULLA
565628 31,1 195 21,7 65,8 23,1 19,6 63,4 29,2 193,8 32,8 152 16-24/25
15.00/2.5 553200
20.5 R 25 Tubeless
-
588 1542 596 17.00/2.0 24/25 VAM
23,1 60,7 23,5 17.00/1.7 CR OR 3-25 SULLA 17-24/25
553200
XG C E2 179E
123691 70 522 1490 684 4528 31 508
(8) 43,5 20,6 58,7 26,9 178,3 39,1 134
TECHNICAL DATA EARTHMOVER TYRES
41
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
bar 2 3 4 5 6 7 7,5 8 9 10
Utilisation
25" psi 29 44 58 73 87 102 109 116 131 145
0 km/h
0mph 9900 12900 15900 18900 21600 24200 25250 26300 28800 31300
5 km/h 7000 9100 11200 13300 15300 17100 18050 19000 23200
3mph
10 km/h 6200 8050 9950 11800 13500 15150 16000 16850 18500
6mph
20 km/h 4450 6000 7350 8650 10000 11250 11950 12600 13900
12mph
505/95 R 25 - 18.00 R 25
9 mph
20 km/h 4450 6000 7350 8650 10000 11250 12600 13900
12mph
30 km/h 2730 3965 5200 6435 7670 8905 10140 11375
XV C E2 E2 Cranes 19mph
40 km/h 2605 3782 4960 6140 7315 8495 9670 10850
25mph
50 km/h 2480 3600 4720 5840 6960 8085 9205 10325
31mph
65 km/h 2225 3235 4240 5245 6255 7260 8270 9275
40mph
70 km/h 2100 3050 4000 4950 5900 6850 7800 8750
43mph
80 km/h 1720 2500 3280 4060 4840 5615 6390 7175
50mph
90 km/h 1470 2135 2800 3465 4130 4795 5460 6125
56 mph
100 km/h 1260 1830 2400 2970 3540 4110 4680 5250
62 mph
0 km/h
0mph 10000 12300 14600 17100 19400 21500
5 km/h 7050 8700 10300 12100 13700 15200
3mph
10 km/h 6250 7700 9150 10700 12150 13450
6mph
20 km/h 4500 5700 6900 8150 9350 10550
12mph
20.5 R 25 - 525/80 R 25
25"
20.5 R 25 Tubeless
XADN E3T ** 177B 28 528 1490 4484 36 474 -
123407 17,4 577 1561 20,8 58,7 667 176,5 45,4 125 24/25 VAM
17.00/2.0 OR 3-25 SULLA
XADT E4T ** 177B 22 22,7 61,5 527 1492 26,3 4489 44 455 17-24/25
123335 13,7 20,7 58,7 176,7 55,4 120 553200
XK A L3 ** 14 562 649 4425 28 485
263460 8,7 22,1 1482 25,6 174,2 35,3 128
XH A L3 * 16 527 58,3 646 4417 495
263451 9,9 20,7 25,4 173,9 131
1561
XSNOPLUS L2T * 16 61,5 534 1471 633 4364 31
123795 9,9 21 57,9 24,9 171,8 39,1 -
500
XTL A L2 * 132
16 532 1480 637 4391 OR 3-25 SULLA
123435
(5) 9,9 20,9 58,3 25,1 172,9 553200 24/25 VAM
577 17.00/2.0
XR D1 A L4 * 22,7 17.00/1.7 17-24/25
14 555 677 4585 43 485 OR 2-25
263402
(8) 8,7 21,9 26,7 180,5 54,2 128 HEUPO
XLD D2 A L5T * 10 534 1530 676 4582 72 427 553201
123325 6,2 1621 21 60,2 26,6 180,4 90,7 113
63,8
XMINE D2 L5R * 6 556 689 4616 74 447
266823 3,7 21,9 27,1 181,7 93,2 118
XSM D2+ L5S 6 534 1524 682 4587 78 410
123667 3,7 21 60 26,9 180,6 98,3 108
525/80 R 25 Tubeless
-
588 1542 17.00/2.0 24/25 VAM
23,1 60,7 17.00/1.7 CR OR 3-25 SULLA 17-24/25
553200
21.00 R 25 Tubeless
-
XS E7 1839 634 558 1750 767 5226 19 700 25 YBAM
15.00/3.0 OR 3-25 SULLA
276670 72,4 25 22 68,9 30,2 205,7 23,9 185 17-24/25
553200
21.00 R 25 Tubeless
XR B E3 ** 35 340 685 560 1738 786 5251 32
270800 -
(8)
21,7 233 634 1839 27 22 68,4 30,9 206,7 40,3 700 15.00/3.0 25 YBAM
25 72,4 185 17.00/3.0 OR 3-25 SULLA
XK A L3 ** 14 609 1768 800 5343 33 17-24/25
553200
270850 8,7 24 69,6 31,5 210,4 41,6
21.00 R 25 Tubeless
-
XK A L3 ** 14 634 1839 609 1768 800 5343 33 700 15.00/3.0 25 YBAM
270850 8,7 25 72,4 24 69,6 31,5 210,4 41,6 185 17.00/3.0 OR 3-25 SULLA 17-24/25
553200
TECHNICAL DATA EARTHMOVER TYRES
43
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XADN ** E3T E3T Articulated dumpers Standard 4750 5000 5250 5750 6000 6250 6800 7050 7300
XADT ** E4T E4T
XK A ** L3 L3
XSNOPLUS * L2T L2T Front tip.load 10000 10575 11150 12300 12800 13450 14650 15200 15850
XH A * L3 L3
XTL A * L2 L2 Loaders Front laden 6250 6615 6980 7700 8000 8400 9150 9500 9900
XR D1 A * L4 L4
XLD D2 A * L5T
20.5 R 25
L5T
XMINE D2 * L5R L5R Rear unladen 5000 5300 5600 6150 6400 6700 7300 7600 7900
XSM D2+ L5S L5S
XK A ** L3 L3
XLD D2 A * L5T L5T Underground machines Front and Rear 5650 5975 6300 6950 7200 7550 8250 8550 8900
XMINE D2 * L5R L5R
XSM D2+ L5S L5S
XTL A * L2 L2
XSNOPLUS * L2T L2T
XH A * L3 L3 Graders Front and Rear 3600 3857 4113 4625
XR D1 A * L4 L4
XLD D2 A * L5T L5T
bar 2 3 4 5 6 7
Utilisation
psi 29 44 58 73 87 102
0 km/h
0mph 10000 12300 14600 17100 19400 21500
5 km/h 7050 8700 10300 12100 13700 15200
3mph
10 km/h 6250 7700 9150 10700 12150 13450
6mph
20 km/h 4500 5700 6900 8150 9350 10550
525/80 R 25 - 20.5 R 25
12mph
30 km/h 3700 4950 6200 7500 8800 10100
19mph
40 km/h
XL B 3525 4700 5900 7150 8350 9600
Cranes 25mph
XG C E2 E2 50 km/h 3375 4475 5600 6800 7950 9150
31mph
65 km/h 3050 4075 5100 6150 7200 8300
40mph
70 km/h 2850 3800 4750 5750 6750 7750
43mph
80 km/h 2325 3125 3900 4725 5550 6350
50mph
90 km/h 2000 2650 3350 4050 4750 5450
56 mph
100 km/h 1700 2275 2850 3450 4050 4650
62 mph
bar 1 1,5 2 2,5 3 3,5 4 4,5 5 6
Utilisation
psi 15 22 29 36 44 51 58 65 73 87
Road in single 2500 3050 3750 4500 5250 6000 6650 7350 8050 9500
Track in single 2750 3750 4750 5800 6800 7800
Sand in single 4250 6000 7600
XS E7 E7 Desert conditions 65 km/h max.
Road in twin 2250 2745 3375 4050 4725 5400 6435 6615 7245 8550
Track in twin 2475 3375 4275 5220 6120 7020
Sand in twin 3825 5400 6840
bar 4 4,5 5 5,5 6 6,5 7 7,5 8
Utilisation
psi 58 65 73 80 87 94 102 109 116
21.00 R 25
XR B ** E3 E3 Transport Standard 8350 9100 9850 10600 11400 12150 12550 12925 13300
XK A ** L3 L3
bar 2 3 4 5 6 7 8
Utilisation
psi 29 44 58 73 87 102 116
XK A ** L3 L3 Underground machines Front and Rear 6600 8500 10400 12300 14250 15650 16600
TECHNICAL DATA EARTHMOVER TYRES
44
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
550/65 R 25 Tubeless
XTL A L2T * 16 540 603 4154 33 446
123316 -
9,9 21,3 23,7 163,5 41,6 118
(5, 8) 1400 OR 3-25 SULLA
55,1 553200 24/25 VAM
XLD 65 L3 L3T * 16 574 1371 549 602 4152 34 17.00/2.0
123570 9,9 22,6 54 21,6 23,7 163,5 42,8 17.00/1.7 17-24/25
450 OR 2-25
XLD 65 SUPER L3 SUPER L3T * 119 HEUPO
123168 14 546 1422 619 4236 41
8,7 21,5 56 24,4 166,8 51,7 553201
(7)
23.5 R 25 Tubeless
-
XL B E2 188E 70 677 1680 732 598 1619 738 4905 27 700 25 WAM
19.50/2.5 OR 3-25 SULLA
123474 43,5 26,7 66,1 28,8 23,5 63,7 29,1 193,1 34 185 18-24/25
553200
23.5 R 25 Tubeless
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XTL A * L2T L2T Front tip.load 7850 8575 9300 10700 11440 12150 13600 14320 15040 16480
XLD 65 L3 * L3T L3T Loaders Front laden 4900 5350 5800 6700 7150 7600 8500 8950 9400 10300
XLD 65 SUPER L3 * SUPER
550/65 R 25
SUPER L3T L3T Rear unladen 3925 4290 4650 5350 5720 6075 6800 7165 7525 8250
XTL A * L2T L2T
XLD 65 L3 * L3T L3T
SUPER Graders Front and Rear 2940 3210 3480 4020 4290 4560 5100
XLD 65 SUPER L3 *
SUPER L3T L3T
bar 2 3 4 5 6 7
Utilisation
psi 29 44 58 73 87 102
0 km/h
0mph 13000 16200 19400 23200 26400 29600
5 km/h 9150 11500 13700 16400 18600 20900
3mph
10 km/h 8100 10150 12150 14500 16500 18500
6mph
20 km/h 5850 7450 9050 10850 12500 14100
23.5 R 25 - 605/80 R 25
12mph
30 km/h 4750 6350 7950 9600 11300 13000
19mph
40 km/h 4550 6050 7550 9200 10800 12400
XL B E2 E2 Cranes 25mph
50 km/h 4325 5750 7200 8750 10300 11800
31mph
65 km/h 3925 5200 6550 7900 9300 10700
40mph
70 km/h 3660 4880 6100 7400 8700 10000
43mph
80 km/h 3000 4000 5000 6050 7150 8200
50mph
90 km/h 2550 3425 4250 5200 6100 7000
56 mph
100 km/h 2100 2925 3650 4400 5200 6000
62 mph
bar 2 2,5 3 3,25 3,5 4 4,5 5 5,5
Utilisation
psi 29 36 44 47 51 58 65 73 80
XK A ** L3 L3
XSNOPLUS * L2T L2T Front tip.load 12950 14550 16250 17050 17850 19450 21350
XTL A * L2 L2
XH A * L3 L3
XHA2 * L3 L3 Loaders Front laden 8100 9100 10150 10650 11150 12150 13350
23.5 R 25
XR D1 A * L4 L4
XLD D2 A * L5T L5T
XMINE D2 L5R L5R Rear unladen 6500 7300 8100 8500 8900 9700 10700
XSM D2+ L5S L5S
XK A ** L3 L3
XLD D2 A * L5T L5T Underground machines Front and Rear 7300 8200 9150 9600 10050 10950 12000
XMINE D2 L5R L5R
XSM D2+ L5S L5S
25"
600/65 R 25 Tubeless
17.00/1.7 -
XLD 65 L3 L3T * 16 636 1438 727 622 1429 618 4246 34 484 -
17.00/2.0 OR 3-25 SULLA
063799 9,9 25 56,6 28,6 24,5 56,3 24,3 167,2 42,8 128 -
19.50/2.5 553200
25/65 R 25 Tubeless
XR B E2 ** -
35 217 705 1554 762 623 1474 664 4450 28 560 19.50/2.0 -
283005 OR 3-25 SULLA
21,7 149 27,8 61,2 30 24,5 58 26,1 175,2 35,3 148 20.00/2.0 -
(8) 553200
650/65 R 25 Tubeless
-
XAD 65 SUPER E3T ** 180B 28 672 1505 630 1494 670 4500 40 595 19.50/2.5 -
840573 17,4 26,5 59,3 24,8 58,8 26,4 177,2 50,4 157 22.00/3.0 OR 3-25 SULLA -
553200
650/65 R 25 Tubeless
-
XLD 65 L3 L3T * 16 672 1505 634 1498 636 4422 37 596 -
19.50/2.5 OR 3-25 SULLA
123820 9,9 26,5 59,3 25 59 25 174,1 46,6 157 -
553200
26.5 R 25 Tubeless
-
XL B E2 195E 70 765 1819 827 670 1752 799 5307 30 860 25 YBAM
22.00/3.0 OR 3-25 SULLA
123484 43,5 30,1 71,6 32,6 26,4 69 31,5 208,9 37,8 227 18-24/25
553200
TECHNICAL DATA EARTHMOVER TYRES
47
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
600/65 R 25
XLD 65 L3 * L3T L3T Loaders Front laden 5650 6675 7700 8725 9750 10725 11700
Rear unladen 4520 5340 6160 6980 7800 8580 9360
XLD 65 L3 * L3T L3T Graders Front and Rear 3390 4005 4600
bar 2 2,5 3 3,25 3,5 4 4,5 5 5,5
Utilisation
psi 29 36 44 47 51 58 65 73 80
25/65 R 25
XR B ** E2 E2 Transport Standard 4950 5367 6100 6375 6650 7200 7750 8300 8600
SUPER
XAD 65 ** SUPER E3T Articulated dumpers Standard 5450 6300 7150 8000
E3T
650/65 R 25
bar 2 2,5 3 3,5 4 4,5 5
Utilisation
psi 29 36 44 51 58 65 73
Front tip.load 10800 12700 14600 16500 18400 20300 22200
XLD 65 L3 * L3T L3T Loaders Front laden 6700 7900 9100 10300 11500 12700 13900
Rear unladen 5400 6350 7300 8250 9200 10150 11100
XLD 65 L3 * L3T L3T Graders Front and Rear 4100 4800 5500 6200 6900 7600 8300
bar 2 3 4 5 6 7
Utilisation
psi 29 44 58 73 87 102
0 km/h
0mph 14900 19400 24000 27800 32000 36900
5 km/h 10500 13700 17000 19600 22600 26000
3mph
10 km/h 9300 12150 15000 17350 20000 23050
6mph
20 km/h 6850 9000 11150 13100 15150 17400
26.5 R 25 - 685/80 R 25
12mph
30 km/h 5850 7800 9750 11800 13800 15800
19mph
40 km/h 5600 7450 9300 11200 13100 15100
XL B E2 E2 Cranes 25mph
50 km/h 5300 7100 8850 10700 12500 14300
31mph
65 km/h 4825 6400 8050 9700 11300 13000
40mph
70 km/h 4500 6000 7500 9050 10600 12150
43mph
80 km/h 3700 4925 6150 7400 8700 9950
50mph
90 km/h 3150 4200 5250 6350 7400 8400
56 mph
100 km/h 2700 3600 4500 5450 6350 7300
62 mph
TECHNICAL DATA EARTHMOVER TYRES
48
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
26.5 R 25 Tubeless
XADN E3T ** 193B 28 670 1740 775 5228 41 900
123427 17,4 26,4 68,5 30,5 205,8 51,7 238
774
XADT E4T ** 193B 30,5 -
22 747 1839 676 1738 5221 52 910 22.00/3.0 IF 25 YBAM
123447 OR 3-25 SULLA
(8) 13,7 29,4 72,4 26,6 68,4 205,6 65,5 240 22.00/3.0 18-24/25
774 553200
X-SUPER TERRAIN AD E4T ** 193B 30,5
689443 24 724 680 1740 5225 54 862
(7) 14,9 28,5 26,8 68,5 205,7 68 228
26.5 R 25 Tubeless
29.5 R 25 Tubeless
-
XS SAND E7 ** 196E 833 1972 747 1820 810 5466 22 1200 25 YBAM
25.00/3.5 OR 3-25 SULLA
458236 32,8 77,6 29,4 71,7 31,9 215,2 27,7 317 19-25
553200
29.5 R 25 Tubeless
29.5 R 25 Tubeless
XADN E3T ** 200B 28 743 1850 817 5541 44 1180
123437 17,4 29,3 72,8 32,2 218,1 55,4 312
XADT E4T ** 200B -
22 833 1972 748 1860 5579 57 1080 25 YBAM
123457 25.00/3.5 OR 3-25 SULLA
(8) 13,7 32,8 77,6 29,4 73,2 219,6 71,8 285 19-25
825 553200
X-SUPER TERRAIN AD E4T ** 200B 32,5
111168 22 762 1858 5576 60 1120
(7) 13,7 30 73,1 219,5 75,6 296
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
26.5 R 25
XH A * L3 L3
XHA2 ** L3 L3
XSM DN L3S L3S Loaders Front laden 9300 10267 12150 12850 13600 15000 16150 17350 18500
XLD D1 A * L4R L4R
XLD D2 A * L5T L5T
XMINE D2 * L5R L5R Rear unladen 7450 8217 9700 10300 10900 12000 12900 13900 14800
XSM D2+ L5S L5S
XK A ** L3 L3
XSM DN L3S L3S
XLD D1 A * L4R L4R Underground machines Front and Rear 8350 9250 10950 11550 12250 13500 14550 15600 16650
XLD D2 A * L5T L5T
XMINE D2 * L5R L5R
XSM D2+ L5S L5S
XH A * L3 L3
L3 Graders Front and Rear 5400 6400 7500
XHA2 ** L3
bar 2 2,3 2,5 2,7 2,9 3,3 3,7 4,1 4,5 4,9
Utilisation
psi 29 33 36 39 42 48 54 60 65 71
Road in single 11000 12000 13000 14000
XS SAND ** E7 E7 Desert conditions 65 km/h max. Track in single 11000 12000 13000 14000
11000 12000 12500 13000 14000
29.5 R 25 - E
Sand in single
bar 2 2,5 3 3,25 3,5 4 4,5 5 5,5
Utilisation
psi 29 36 44 47 51 58 65 73 80
XK A ** L3 L3 Front tip.load 15600 17200 20450 21650 22800 25200 27250 29350 31350
XH A * L3 L3
XLD D1 A * L4R L4R Loaders Front laden 11150 12285 14600 15450 16300 18000 19450 20950 22400
XLD D2 A * L5T L5T
XMINE D2 L5R L5R Rear unladen 8900 9833 11700 12350 13050 14400 15550 16750 17900
XK A ** L3 L3
XLD D1 A * L4R L4R
L5T Underground machines Front and Rear 10050 11050 13150 13900 14650 16200 17500 18850 20150
XLD D2 A * L5T
XMINE D2 L5R L5R
TECHNICAL DATA EARTHMOVER TYRES
50
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
25"
750/65 R 25 Tubeless
22.00/3.0 -
XAD 65 SUPER E3T ** 190B 28 792 1639 738 1599 702 4777 43 810 -
24.00/3.0 OR 3-25 SULLA
123895 17,4 31,2 64,5 29,1 63 27,6 188,1 54,2 214 25.00/3.0 -
553200
750/65 R 25 Tubeless
-
XLD 65 L3 L3T * 16 792 1639 747 1591 683 4714 41 788 22.00/3.0 -
123940 9,9 31,2 64,5 29,4 62,6 26,9 185,6 51,7 208 24.00/3.0 OR 3-25 SULLA -
553200
850/65 R 25 Tubeless
25.00/3.5 -
XAD 65 SUPER E3T ** 196B 28 896 1773 811 1729 753 5150 47 1115 -
27.00/3.0 OR 3-25 SULLA
978610 17,4 35,3 69,8 31,9 68,1 29,6 202,8 59,2 295 27.00/3.5 -
553200
26"
480/80 R 26 Tubeless
XMCL 160A8/160B 479 1428 626 487 1422 636 4220 36 405 DW15L - KLEBER 716
719306 18,9 56,2 24,6 19,2 56 25 166,1 45,4 107 DW16L -
28"
440/80 R 28 Tubeless
XMCL 156A8/156B 441 1415 822 459 1410 641 4200 36 347 DW14L - KLEBER 822
316223 17,4 55,7 32,4 18,1 55,5 25,2 165,4 45,4 92 DW15L -
29"
26.5 R 29 Tubeless
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
SUPER
XAD 65 ** SUPER E3T Articulated dumpers Standard 7350 8400 8950 9500 10600
E3T
750/65 R 25
bar 2 2,5 3 3,25 3,5 4 4,5 5 5,5
Utilisation
psi 29 36 44 47 51 58 65 73 80
Front tip.load 11750 13600 15450 16375 17300 19150 21000 22850 24700
XLD 65 L3 * L3T L3T Loaders Front laden 8400 9720 11040 11700 12360 13680 15000 16320 17640
Rear unladen 6725 7775 8825 9365 9900 10950 12000 13050 14100
XLD 65 L3 * L3T L3T Graders Front and Rear 5040 5830 6620 7020 7420 8210
bar 2,75 3 3,25 3,5 3,75 4
Utilisation
psi 40 44 47 51 54 58
850/65 R 25
SUPER
XAD 65 ** SUPER E3T Articulated dumpers Standard 9500 10450 11175 11900 12500 13250
E3T
480/80 R 26 - 160A8/160B
Static 4900 5990 7080 8170 9260 10350
Cyclic 3200 3910 4620 5330 6040 6750
XMCL Backhoe loaders 30 km/h 2790 3300 3800 4310 4820
19mph
40 km/h 2575 3055 3540 4020 4500
25mph
440/80 R 28
Cyclic 2840 3470 4110 4740 5370 6000
XMCL Backhoe loaders 30 km/h 2480 2930 3380 3830 4280
19mph
40 km/h 2300 2725 3150 3575 4000
25mph
Front tip.load 15050 17075 19100 21200 23250 24250 25275 27300 29250
XK A ** L3 L3
26.5 R 29
Loaders Front laden 10750 12200 13650 15150 16600 17325 18050 19500 20900
XSM DN * L3S L3S
Rear unladen 8600 9750 10925 12125 13275 13850 14450 15600 16725
XK A ** L3 L3
L3S Underground machines Front and Rear 9700 11000 12300 13650 14950 15600 16250 17550 18800
XSM DN * L3S
TECHNICAL DATA EARTHMOVER TYRES
52
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
29"
29.5 R 29 Tubeless
XR B E3 ** 35 420 746 1956 862 5861 37 1290
274012 -
(8)
21,7 288 833 2126 29,4 77 33,9 230,7 46,6 341 24.00/3.5 29 YEAM1
32,8 83,7 25.00/3.5 OR 3-29
XTS E3T ** 29 348 765 1963 869 5884 43 1300 19-29
553202
708648 18 238 30,1 77,3 34,2 231,7 54,2 343
XK A L3 ** 14 793 1958 844 5812 38 1260
274110 8,7 31,2 77,1 33,2 228,8 47,9 333
2074
XH A L3 * 81,7
16 752 1954 839 5795 40 1245
123268
(8) 9,9 29,6 76,9 33 228,1 50,4 329
-
833 24.00/3.5 29 YEAM1
XLD D2 A L5T * 10 772 2004 864 5949 95 985
123279 6,2 32,8 30,4 78,9 34 234,2 119,7 260 25.00/3.5 OR 3-29 19-29
553202
XMINE D2 L5R 6 2126 795 2002 879 5983 100 990
274050 3,7 83,7 31,3 78,8 34,6 235,6 126 262
XSM D2+ L5S 6 770 1993 842 5872 112 1116
123697 3,7 30,3 78,5 33,1 231,2 141,1 295
30/65 R 29 Tubeless
XR DN A L3 * 16 1840 1742 753 5178 35 945
283103 9,9 72,4 68,6 29,6 203,9 44,1 250 -
(8) 846 788 22.00/3.0 -
XR D2 A L5 * 33,3 31 24.00/3.0 OR 3-29
10 1886 1782 784 5325 87 850 -
283104 553202
(8) 6,2 74,3 70,2 30,9 209,6 109,6 225
775/65 R 29 Tubeless
24.00/3.0 -
XAD 65 SUPER E3T ** 195B 28 809 1775 785 1759 779 5272 45 1050 -
24.00/3.5 OR 3-29
510085 17,4 31,9 69,9 30,9 69,3 30,7 207,6 56,7 277 -
25.00/3.5 553202
33.25 R 29 Tubeless
XR B E3 ** 35 518 835 2074 930 6245 40 1600
283910 -
21,7 355 938 2198 32,9 81,7 36,6 245,9 50,4 423 29 YEAM1
(8) 27.00/3.5 OR 3-29
36,9 86,5 19-29
XTS E3T ** 29 429 873 2068 923 6218 45 1640 553202
871916 18 294 34,4 81,4 36,3 244,8 56,7 433
875/65 R 29 Tubeless
27.00/3.0 -
XAD 65 SUPER E3T ** 203B 28 923 1909 883 1881 827 5623 51 1376 -
27.00/3.5 OR 3-29
086953 17,4 36,3 75,2 34,8 74,1 32,6 221,4 64,3 364 -
28.00/3.5 553202
TECHNICAL DATA EARTHMOVER TYRES
53
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XR B ** E3 E3 Scrapers Standard 9150 10325 11500 12650 13850 14425 15000 16150 16750
XTS ** E3T E3T
XK A ** L3 L3 Front tip.load 18350 20600 22800 25050 27300 28750 30150 33050 35300
29.5 R 29
XH A * L3 L3
XLD D2 A * L5T L5T Loaders Front laden 13100 14700 16300 17900 19500 20525 21550 23600 25200
XMINE D2 L5R L5R
XSM D2+ L5S L5S Rear unladen 10475 11750 13050 14325 15600 16425 17250 18875 20150
XK A ** L3 L3
XLD D2 A * L5T L5T Underground machines Front and Rear 11800 13250 14650 16100 17550 18450 19400 21250 22700
XMINE D2 L5R L5R
XSM D2+ L5S L5S
XLD D2 A * L5T L5T Graders Front and Rear 7850 8800 9800
Front tip.load 14000 16100 18200 20300 22400 23100 23800 25200 27600
30/65 R 29
XR DN A * L3 L3 Loaders Front laden 10000 11500 13000 14500 16000 16500 17000 18000 19700
XR D2 A * L5 L5
Rear unladen 8000 9200 10400 11600 12800 13200 13600 14400 15750
SUPER
XAD 65 ** SUPER E3T Articulated dumpers Standard 6900 8100 9350 10700 12150
E3T
775/65 R 29
Front tip.load 13300 15400 17500 19600 21700 22750 23800 25900
XLD 65 SUPER L3 SUPER Loaders Front laden 9500 11000 12500 14000 15500 16250 17000 18500
SUPER L3T L3T
Rear unladen 7600 8800 10000 11200 12400 13000 13600 14800
800/65 R 29
Front tip.load 14150 16500 18900 21300 23650 24500 26050 28400 30800
XLD 65 L3 * L3T L3T Loaders Front laden 10100 11800 13500 15200 16900 17500 18600 20300 22000
Rear unladen 8100 9450 10800 12150 13500 14000 14900 16250 17600
bar 2 2,5 3 3,5 4 4,25 4,5 5 5,5 6
Utilisation
psi 29 36 44 51 58 62 65 73 80 87
33.25 R 29
XR B ** E3 E3 Scrapers Standard 9500 11000 12500 14000 15500 16300 17000 18500 19250 20000
XTS ** E3T E3T
875/65 R 29
SUPER
XAD 65 ** SUPER E3T Articulated dumpers Standard 9100 10800 12500 14100 15500
E3T
TECHNICAL DATA EARTHMOVER TYRES
54
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
33"
18.00 R 33 Tubeless
XV C E2 ** 50 436 496 1820 822 26 640
271325 31,1 299 19,5 71,7 32,4 32,8 169
1896 5486
XR B E3 ** 74,6 216
35 305 490 1816 821 28 580
271220
(8) 21,7 209 19,3 71,5 32,3 35,3 153
X-HAUL E4P ** 30 495 1860 856 5657 49
205207 18,6 262 19,5 73,2 33,7 222,7 61,7
XDT B E4T ** 30 179 -
123733 18,6 553 598 33 VFAM
605 13.00/2.5 OR 3-33
XDT A E4T ** 21,8 23,5 160 16-33
22 192 494 1868 885 5745 54 553203
123713
(8) 13,7 132 1960 19,4 73,5 34,8 226,2 68
77,2
XDT A4 E4T ** 18 157
123723 11,2 108
X-QUARRY E4R ** 14 122 505 1873
123567 8,7 84 19,9 73,7 852 5670 62 600
X-QUARRY S E4R ** 19 166 511 1864 33,5 223,2 78,1 159
873291 11,8 114 20,1 73,4
21.00 R 33 Tubeless
-
X-HAUL S E4P ** 25 280 629 2042 685 550 1966 895 5955 53 820 33 VFAM
15.00/3.0 OR 3-33
612785 15,5 192 24,8 80,4 27 21,7 77,4 35,2 234,4 66,8 217 16-33
553203
33.5 R 33 Tubeless
XR B E3 ** -
35 560 944 2354 1020 846 2228 986 6685 40 1680 33/35 YEAM
283412 28.00/4.0 OR 3-33
(8) 21,7 384 37,2 92,7 40,2 33,3 87,7 38,8 263,2 50,4 444 20-33
553203
35/65 R 33 Tubeless
XR DN A L3 * 16 2124 911 2010 894 6036 38 1555
283500 9,9 83,6 35,9 79,1 35,2 237,6 47,9 411
XSM DN L3S 14 918 2012 887 6022 44 1544
123052 8,7 36,1 79,2 34,9 237,1 55,4 408
XLD D1 A L4R * 14 914 2056 883 6095 60 1550 -
123084 8,7 987 36 80,9 34,8 240 75,6 410 -
28.00/3.5 OR 3-33
XMINE D2 L5R * 6 38,9 2176 921 2050 904 6136 93 1350 -
123494 3,7 85,7 36,3 80,7 35,6 241,6 117,2 357 553203
XLD D2 A L5T * 10 914 2058 886 6106 1450
123343 6,2 36 81 34,9 240,4 97 383
XSM D2+ L5S 6 921 2050 905 6139 122,2 1350
123529 3,7 36,3 80,7 35,6 241,7 357
35/65 R 33 Tubeless
-
XLD D1 A L4R ** 14 987 2176 914 2056 899 6136 60 1550 -
28.00/3.5 OR 3-33
143231 8,7 38,9 85,7 36 80,9 35,4 241,6 75,6 410 -
553203
37.5 R 33 Tubeless
XR B E3 ** -
35 680 1057 2513 1142 953 2370 1057 7118 47 2310 -
283612 32.00/4.5 OR 3-33
(8) 21,7 466 41,6 98,9 45 37,5 93,3 41,6 280,2 59,2 610 -
553203
TECHNICAL DATA EARTHMOVER TYRES
55
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XV C ** E2 E2
XR B ** E3 E3
X-HAUL ** E4P E4P
XDT B ** E4T E4T Transport Standard 7950 8700 9400 10150 10900 11270 11650 12000
XDT A ** E4T E4T
XDT A4 ** E4T E4T
X-QUARRY S ** E4R E4R
18.00 R 33
E4R 30 km/h
X-QUARRY ** E4R Quarry transport 5600 7700 9350 10150 10900 11650 12400
19mph
21.00 R 33
X-HAUL S ** E4P E4P Transport Standard 9315 10250 11185 12125 13065 14000 14470
33.5 R 33
XR B ** E3 E3 Transport Standard 17000 18500 20000 20750 21500
Front laden 13740 14840 16090 17720 19000 21200 23000 24150 25300
35/65 R 33 *
XR DN A * L3 L3
XSM DN L3S L3S
XLD D1 A * L4R L4R Loaders
XMINE D2 * L5R L5R
XLD D2 A * L5T L5T
XSM D2+ L5S L5S
Rear unladen 10990 11872 12872 14176 15200 16960 18400 19320 20240
Front laden 16090 17720 19000 21200 23000 24300 25750 28000 28800 29600
XLD D1 A ** L4R L4R Loaders
Rear unladen 12870 14176 15200 16960 18400 19440 20600 22400 23040 23680
35"
21.00 R 35 Tubeless
XR B E3 ** 35 406 2093 568 1996 911 6017 32 840
271410 21,7 278 82,4 22,4 78,6 35,9 236,9 40,3 222
(8)
XK D1 A E4 ** 18 209 582 2047 6212 52
271440 11,2 143 22,9 80,6 244,6 65,5 -
XDT B E4T ** 30 348 634 685 937 900 15.00/3.0 -
123881 18,6 238 25 27 576 2062 36,9 6242 61 238 17.00/3.0 OR 3-35
2145 -
XDT A4 E4T ** 18 209 22,7 81,2 245,7 76,9 553204
84,4
123921 11,2 143
X-QUARRY E4R **
606710 14 122 582 2066 933 6329 68 880
(7) 8,7 84 22,9 81,3 36,7 249,2 85,7 232
21.00 R 35 Tubeless
-
XK D1 A E4 ** 18 209 634 2145 685 582 2047 937 6212 52 900 15.00/3.0 -
271440 11,2 143 25 84,4 27 22,9 80,6 36,9 244,6 65,5 238 17.00/3.0 OR 3-35 -
553204
24.00 R 35 Tubeless
29.5 R 35 Tubeless
XR B E3 ** 35 448 747 2114 946 6365 37 1400
283812 -
21,7 307 833 2226 29,4 83,2 37,2 250,6 46,6 370 25.00/3.5 33/35 YEAM
(8) OR 3-35
32,8 87,6 27.00/3.5 20-35
XTS E3T ** 29 371 777 2116 943 6539 45 1494 553204
631225 18 254 30,6 83,3 37,1 257,4 56,7 395
33.25 R 35 Tubeless
XR B E3 ** -
35 560 938 2350 835 2222 992 6682 40 1580 27.00/3.5 33/35 YEAM
284012 OR 3-35
21,7 384 36,9 92,5 32,9 87,5 39,1 263,1 50,4 417 29.00/3.5 20-35
(8) 553204
37.25 R 35 Tubeless
XR B E3 ** 35 661 929 1066 7146 2250
284251 21,7 453 36,6 42 281,3 594
(8) 2509 2370 47 -
1050 98,8 93,3 59,2 29.00/3.5 33/35 YEAM
XTS E3T ** 29 540 956 1067 7149 2400 OR 3-35
41,3 31.00/4.0 20-35
540244 18 370 37,6 42 281,5 634 553204
XRS B E4R ** 22 415 2572 947 2364 1063 7127 53 2250
123673 13,7 284 101,3 37,3 93,1 41,9 280,6 66,8 594
TECHNICAL DATA EARTHMOVER TYRES
57
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XR B ** E3 E3
XK D1 A ** E4 E4 Transport Standard 11450 12450 13500 14500 15000 15500
XDT B ** E4T E4T
XDT A4 ** E4T E4T
21.00 R 35
E4R 30 km/h
X-QUARRY ** E4R Quarry transport 12450 13500 14500 15000 15500
19mph
XK D1 A ** E4 E4 Underground machines Front and Rear 9250 10500 11750 13050 14300 15600 16850 18150 18775 19400
XV C ** E2 E2
XR B ** E3 E3
XK D1 B ** E4 E4
X-HAUL ** E4P E4P
XDT C4 ** E4T E4T Transport Standard 13950 15050 16300 17350 18500 19050 19625 20200
XDT B ** E4T E4T
XDT A ** E4T E4T
XDT A4 ** E4T E4T
24.00 R 35
X-QUARRY S ** E4R E4R
E4R 30 km/h
X-QUARRY ** E4R Quarry transport 12000 14500 16000 17250 18500 20000
19mph
XR B ** E3 E3
XTS ** E3T E3T Scrapers Standard 17950 18500 19350 20200 21900 23600 24450 25300
XRS B ** E4R E4R
TECHNICAL DATA EARTHMOVER TYRES
58
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
39"
37.5 R 39 Tubeless
XR B E3 ** 35 721 958 2524 1118 7567 47 2680
284410 21,7 494 37,7 99,4 44 297,9 59,2 708 -
(8) 1057 2665 -
32.00/4.5 OR 3-39
XRS B E4R ** 41,6 104,9 -
856011 22 453 976 2517 1130 7583 56 2624 553206
(7) 13,7 310 38,4 99,1 44,5 298,5 70,6 693
40.5/75 R 39 Tubeless
XMS B E3R ** 33 766 -
379296 20,5 525 1142 2758 998 2588 1151 7770 51 2940 -
32.00/4.5 OR 3-39
XMS A E3R ** 20 500 45 108,6 39,3 101,9 45,3 305,9 64,3 777 -
224334 12,4 342 553206
45/65 R 39 Tubeless
XLD D2 A L5T * 10 1102 2577 1086 7586 115 2760 -
123681 6,2 1269 2707 43,4 101,5 42,8 298,7 144,9 729 32.00/4.5 -
XMINE D2 L5R * 6 50 106,6 1099 2580 1110 7653 116 2712 36.00/4.5 OR 3-39 -
123305 3,7 43,3 101,6 43,7 301,3 146,1 717 553206
45"
45/65 R 45 Tubeless
XLD D1 A L4R * 14 1130 1156 7995 71 3330
123671 8,7 44,5 2700 45,5 314,8 89,4 880
XLD D2 A L5T * 10 1147 106,3 1157 7997 115
123641 6,2 45,2 45,6 314,8 144,9 3020 -
1269 2860 -
XMINE D2 L5R * 6 1159 2697 1163 8009 116 798 36.00/4.5 OR 9.8-45
50 112,6 -
123315 3,7 45,6 106,2 45,8 315,3 146,1 553214
XSM D2+ L5S
123769 6 1145 2737 1223 8347 120 3250
(8) 3,7 45,1 107,8 48,1 328,6 151,2 859
49"
24.00 R 49 Tubeless
XR B E3 ** 35 610 2582 644 2480 1133 7522 37 1500
280400 21,7 418 101,7 25,4 97,6 44,6 296,1 46,6 396
XDR B E4R ** 26 453
123235 16,2 310
XDR B4 E4R ** 22 384 657 2509 1144 7603 1420
123115 13,7 263 25,9 98,8 45 299,3 375 -
XDR A E4R ** 18 314 725 784 -
17.00/3.5 OR 3-49
123095 11,2 215 28,5 2634 30,9 68 -
XDT B E4T ** 30 523 103,7 85,7 553205
123793 18,6 358
XDT A E4T ** 22 384 645 2527 1156 7667 1500
123803 13,7 263 25,4 99,5 45,5 301,9 396
XDT A4 E4T ** 18 314
123823 11,2 215
TECHNICAL DATA EARTHMOVER TYRES
59
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
37.5 R 39
XR B ** E3 E3 Transport Standard 18100 20000 21900 22900 23850 25750 26700 27650
XRS B ** E4R E4R
40.5/75 R 39
XMS B ** E3R E3R Scrapers Standard 20200 22400 24600 25700 26800 29000 30100 31200
XMS A ** E3R E3R
45/65 R 39
Front laden 31130 35600 38530 40000 42000 45500 49000 52550
XLD D2 A * L5T L5T Loaders
XMINE D2 * L5R L5R
Rear unladen 24900 28500 30800 32000 33600 36400 39200 42050
Front laden 31000 35600 40200 42500 45000 49550 54200 58850 63500
45/65 R 45
XLD D1 A * L4R L4R
XLD D2 A * L5T L5T Loaders
XMINE D2 * L5R L5R
XSM D2+ L5S L5S
Rear unladen 24800 28500 32150 34000 36000 39650 43350 47100 50800
XR B ** E3 E3
XDT B ** E4T E4T 24.00 R 49
XDR B ** E4R E4R
XDT A ** E4T E4T Transport Standard 13900 15250 16550 17850 19200 20500 21800 22450 23100 23350
XDR B4 ** E4R E4R
XDR A ** E4R E4R
XDT A4 ** E4T E4T
TECHNICAL DATA EARTHMOVER TYRES
60
MICHELIN TYRE CHARACTERISTICS
COMMERCIAL Max. Standardized dimensions DIMENSIONAL CHARACTERISTICS (2)
Measuring Tubeless Tube Type
DESCRIPTION dist. TKPH maximum in service Michelin dimensions Rim
/ hour TMPH e D E e D R’ RC Tread depth Cap. Approved O-Ring Ref.
km (1) mm mm mm mm mm mm mm mm l Rims CAI Flap
Types (3) - (4) (4)
CAI (Part Number) Miles (4)
inches inches inches inches inches inches inches 32rd gallon
49"
27.00 R 49 Tubeless
XV C E2 ** 50 1090 745 2648 1170 7934 33 2060
280557 31,1 747 29,3 104,3 46,1 312,4 41,6 544
X-TRACTION S RD B E3T ** 35 763 2761
689287 21,7 523 108,7 734 2622 1191 7936 46 1903
X-TRACTION S RD A E3T ** 27 589 28,9 103,2 46,9 312,4 58 503
504986 16,8 403
XDT B E4T ** 30 654
123783 18,6 448
XDT A E4T ** 22 480 726 2696 1221 8151 74 1935
123763 13,7 329 28,6 106,1 48,1 320,9 93,2 511
XDT A4 E4T ** 18 392 -
123773 11,2 269 818 884 19.50/4.0 -
XDR B E4R ** 26 567 32,2 34,8 22.00/4.0 OR 3-49 -
123330 16,2 388 553205
XDR B4 E4R ** 22 480 2819 2694 1223 8152 76 1978
123210 13,7 329 111 106,1 48,1 320,9 95,7 523
XDR A E4R ** 18 392
123170 11,2 269 729
X-TRACTION RD B E4T ** 30 654 28,7
470320 18,6 448
X-TRACTION RD B4 E4T ** 26 567 2718 1226 8159 81 1915
166905 16,2 388 107 48,3 321,2 102 506
X-TRACTION RD A4 E4T ** 18 392
495676 11,2 269
51"
30.00 R 51 Tubeless
XV C E2 ** 50 1340 2970 833 2837 1251 8491 37 2607
284697 31,1 918 116,9 32,8 111,7 49,3 334,3 46,6 689
XDR B E4R ** 24 643 -
123151 14,9 440 914 988 -
22.00/4.5 OR 4-51
XDR B4 E4R ** 20 536 36 3033 38,9 835 2878 1291 8671 83 2490 -
123041 12,4 367 119,4 32,9 113,3 50,8 341,4 104,6 658 553210
XDR A E4R ** 16 429
123450 9,9 294
33.00 R 51 Tubeless
XDC C4 E3V ** 45 1395
645788 28 956
XDC B E3V ** 39 1209 889 2966 1332 8938 48
020166 24,2 828 35 116,8 52,4 351,9 60,5
XDC B4 E3V ** 34 1054
139019 21,1 722
XDT B E4T ** 30 930
123961 18,6 637
XDT B4 E4T ** 26 806
123843 16,2 552 911 3040 1365 9159 87 3090 -
XDT A E4T ** 22 682 992 3202 1073 35,9 119,7 53,7 360,6 109,6 816 -
24.00/5.0 OR 4-51
123971 13,7 467 39,1 126,1 42,2 -
XDT A4 E4T ** 18 558 553210
123981 11,2 382
XDR C4 E4R ** 27 837
839917 16,8 573
XDR B E4R ** 24 744
123411 14,9 510 907 3032 1353 9116 88 3000
XDR B4 E4R ** 20 620 35,7 119,4 53,3 358,9 110,9 793
123281 12,4 425
XDR A E4R ** 16 496
123161 9,9 340
TECHNICAL DATA EARTHMOVER TYRES
61
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
XV C ** E2
X-TRACTION S RD B
** E3T E2
X-TRACTION S RD A E3T
** E3T E3T
XDT B ** E4T E4T
27.00 R 49
XDT A ** E4T E4T
XDT A4 ** E4T E4T Transport Standard 16850 18550 20300 22050 24000 25500 27250 28100 29000 29850
XDR B ** E4R E4R
XDR B4 ** E4R E4R
XDR A ** E4R E4R
X-TRACTION RD B ** E4T E4T
X-TRACTION RD B4 E4T
** E4T E4T
X-TRACTION RD A4
** E4T
30.00 R 51
XV C ** E2 E2
XDR B ** E4R E4R Transport Standard 22100 24350 26650 28950 31200 33500 34650 35800
XDR B4 ** E4R E4R
XDR A ** E4R E4R
51"
36.00 R 51 Tubeless
XDC C4 E3V ** 40 1480
975610 24,9 1014
XDC B E3V ** 1008 3145 1376 9387 57
37 1369
320300 39,7 123,8 54,2 369,6 71,8
(7) 23 938
XDC B4 E3V ** 34 1258 -
1097 3338 1186 3980 -
448558 21,1 862 26.00/5.0 OR 4-51
43,2 131,4 46,7 1052 -
XDR B E4R ** 24 888 553210
123122 14,9 608
XDR B4 E4R ** 20 740 1011 3215 1430 9653 96
123002 12,4 507 39,8 126,6 56,3 380 120,9
XDR A E4R ** 16 592
123042 9,9 406
50/65 R 51 Tubeless
XMINE D2 SR L5R ** 6
970863 3,7 -
(7) 1410 3133 1524 1273 3073 1368 9228 116 4463 -
40.00/4.5 OR 4-51
XMINE D2 HR L5R ** 55,5 123,3 60 50,1 121 53,9 363,3 146,1 1179 -
523260 6 553210
(7) 3,7
57"
37.00 R 57 Tubeless
XDR C E4R ** 30 1272
396514 18,6 871
XDR C4 E4R ** 27 1145
123073 16,8 784
XDR B E4R ** 24 1018 1040 3456 1576 10645 98
123482 14,9 697 40,9 136,1 62 419,1 123,5 -
XDR B4 E4R ** 20 848 1118 3597 1219 27.00/6.0 -
123362 12,4 581 44 141,6 48 29.00/6.0 OR 4-57 -
XDR A E4R ** 16 678 553211
123242 9,9 464
XDM B E4T ** 24 1018
475323 14,9 697 1022 3453 1678 10725 99
XDM B4 E4T ** 20 848 40,2 135,9 66,1 422,2 124,7
725325 12,4 581
40.00 R 57 Tubeless
XDM C E3V ** 33 1584
150406 20,5 1085
XDM C4 E3V ** 30 1440
816612 18,6 986 1106 3497 1537 10452 64 5628
XDM B E3V ** 26 1248 43,5 137,7 60,5 411,5 80,6 1487
542825 16,2 855
XDM B4 E3V ** 22 1056 -
601458 13,7 723 29.00/6.0 -
1218 3766 1316 32.00/6.0 OR 4-57
XDR C E4R ** 30 1440 48 148,3 51,8 32.00/5.0 -
765274 18,6 986 553211
XDR C4 E4R ** 27 1296
123443 16,8 888 1121 3570 1569 10673 97
XDR B E4R ** 24 1152 44,1 140,6 61,8 420,2 122,2
123323 14,9 789
XDR B4 E4R ** 20 960
123193 12,4 658
50/80 R 57 Tubeless
XDR C4 E4R ** 26 1518
929814 16,2 1040
(7)
XDR B E4R ** -
22 1285 1342 3619 1562 1281 3624 1562 10758 94 6589 -
966177 34.00/6.0 OR 4-57
(7) 13,7 880 52,8 142,5 61,5 50,4 142,7 61,5 423,5 118,4 1741 -
553211
XDR B4 E4R **
310787 20 1168
(7) 12,4 800
TECHNICAL DATA EARTHMOVER TYRES
63
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
36.00 R 51
XDC B ** E3V E3V
XDC B4 ** E3V E3V Transport Standard 30450 33600 36800 39950 43100 46250 47850 49400 51000
XDR B ** E4R E4R
XDR B4 ** E4R E4R
XDR A ** E4R E4R
50/65 R 51
Front laden 46500 50500 54500 58500 62500 65000
XMINE D2 SR ** L5R L5R Loaders
XMINE D2 HR ** L5R L5R
Rear unladen 37200 40400 43600 46800 50000 52000
37.00 R 57
XDR B ** E4R E4R
XDR B4 ** E4R E4R Transport Standard 38550 42200 45800 49400 53000 54850 56650 58450
XDR A ** E4R E4R
XDM B ** E4T E4T
XDM B4 ** E4T E4T
57"
50/80 R 57 Tubeless
XDR C4 E4R ** 26 1394
929814 16,2 955
(7)
XDR B E4R ** -
22 1179 1342 3619 1562 1253 3625 1562 10758 94 6420 32.00/6.0 -
966177 OR 4-57
13,7 808 52,8 142,5 61,5 49,3 142,7 61,5 423,5 118,4 1696 34.00/6.0 -
(7) 553211
XDR B4 E4R **
310787 20 1072
(7) 12,4 734
50/90 R 57 Tubeless
XDR C4 E4R ** 28 1747
388084 17,4 1197 -
XDR B E4R ** 24 1498 1397 3609 1575 1260 3840 1696 11501 107 -
32.00/6.5 OR 4-57
894079 14,9 1026 55 142,1 62 49,6 151,2 66,8 452,8 134,8 -
XDR B4 E4R ** 20 1248 553211
289603 12,4 855
55/80 R 57 Tubeless
XMINE D2 LC L5R * 6
594400 3,7 -
XMINE D2 HR L5R * 6 1537 3784 1430 3740 1633 11154 119 7967 42.00/5.0 -
817367 3,7 60,5 149 56,3 147,2 64,3 439,1 149,9 2105 44.00/5.0 OR 4-57 -
XMINE D2 SR L5R * 6 553211
635563 3,7
60/80 R 57 Tubeless
XMINE D2 HR L5R * 6
114447 3,7
(7) -
XMINE D2 SR L5R * 6 1520 3949 1714 11750 118 10022 -
47.00/5.0 OR 4-57
964380 3,7 59,8 155,5 67,5 462,6 148,7 2648 -
XMINE D2 LC L5R * 553211
158276 6
(7) 3,7
63"
53/80 R 63 Tubeless
XK D1 C4 E4R ** 28 1837
123579 17,4 1258
XK D1 B E4R ** 24 1574
123569 14,9 1078 1330 3750 1630 11168 88
XK D1 B4 E4R ** 20 1312 52,4 147,6 64,2 439,7 110,9
123559 12,4 899 -
XK D1 A E4R ** 16 1050 1481 3846 1669 36.00/5.0 -
123539 9,9 719 58,3 151,4 65,7 38.00/5.0 OR 4-63 -
XDR B E4R ** 24 1574 553056
026549 14,9 1078
XDR B4 E4R ** 20 1312 1342 3776 1635 11227 105
881484 12,4 899 52,8 148,7 64,4 442 132,3
XDR A E4R ** 16 1050
983096 9,9 719
56/80 R 63 Tubeless
XDR C4 E4R ** 28 2150
282261 17,4 1473
XDR B E4R ** 24 1843
819341 14,9 1262 -
1764 1425 3998 1727 11876 105 9547 41.00/5.0 [6.0] -
XDR B4 E4R ** 20 1536 69,4 56,1 157,4 68 467,6 132,3 2522 41.00/5.0 [5.5] OR 4-63
380744 12,4 1052 -
553056
XDR A E4R **
741846 16 1229
(7) 9,9 842
TECHNICAL DATA EARTHMOVER TYRES
65
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
50/80 R 57 (32.00/6.0)
XDR C4 ** E4R E4R
XDR B ** E4R E4R Transport Standard 57820 62410 67000 69290 71590
XDR B4 ** E4R E4R
50/90 R 57
XDR C4 ** E4R E4R
XDR B ** E4R E4R Transport Standard 52850 57800 62750 67700 72650 75320 78000 80660
XDR B4 ** E4R E4R
55/80 R 57
Front laden 75000 80000 85000 90000 95000 100000 105000
XMINE D2 LC * L5R L5R
XMINE D2 SR * L5R L5R Loaders
XMINE D2 HR * L5R L5R
Rear unladen 60000 64000 68000 72000 76000 80000 84000
60/80 R 57
XMINE D2 HR * L5R L5R
XMINE D2 LC * L5R L5R Loaders
XMINE D2 SR * L5R L5R
Rear unladen 60000 66400 72800 79200 85600 92000 98400
XK D1 C4 ** E4R E4R
XK D1 B ** E4R E4R
53/80 R 63
XK D1 B4 ** E4R E4R
XK D1 A ** E4R E4R Transport Standard 59660 65240 70830 76410 82000 85010 86822 88030
XDR B ** E4R E4R
XDR B4 ** E4R E4R
XDR A ** E4R E4R
63"
59/80 R 63 Tubeless
XDR S C4 E4S ** 32 2535
784092 19,9 1736
(7)
XDR S B E4S ** 1501 11966 71
28 2218
364848 59,1 471,1 89,4
(7) 17,4 1519
XDR S B4 E4S ** 24 1901
524264
(7) 14,9 1302
-
XDR C4 E4R ** 1648 4143 1858 4028 1740 44.00/5.0 [6.0] -
28 2218 10160 OR 4-63
416440 64,9 163,1 73,1 158,6 68,5 44.00/5.0 [5.5] -
(7) 17,4 1519 2684 553056
XDR B E4R ** 24 1901
443800
(7) 14,9 1302 1503 11970 116
59,2 471,3 146,1
XDR B4 E4R ** 20 1584
037664
(7) 12,4 1085
XDR A E4R ** 16 1267
490159 9,9 868
TECHNICAL DATA EARTHMOVER TYRES
67
TYRE LOADS IN KG/LB - TYRE PRESSURES IN BAR/PSI
Identi-
fication
Tread Explanations on how to choose the tyre and to determine the inflation pressures
Size
code
type Refer to explanations and methods allowing to determine the inflation pressures (10)
(9)
59/80 R 63
XDR S B4 ** E4S E4S
XDR C4 ** E4R E4R Transport Standard 99000 102100 104000
XDR B ** E4R E4R
XDR B4 ** E4R E4R
XDR A ** E4R E4R
TECHNICAL DATA EARTHMOVER TYRES
68
NOTES
TECHNICAL DATA EARTHMOVER TYRES
69
COMPONENTS USED WITH MICHELIN EARTHMOVER TYRES AND RIMS
CONTENTS
Tubes 76 and 77
Flaps 76 and 77
Seals 78
Valves (*) 79 to 85
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
DW rim DEEP WELL 18 x DW 10 254 25.4 513 335/80 R 18
10.0 1.0 20.2
18 x DW 11 279.4 25.4 513 335/80 R 18
11.0 1.0 20.2
F 24 x DW 10 254 25.4 665 11.2 LR 24
10.0 1.0 26.2
H 24 x DW 12 304.8 25.4 665 14.9 R 24
12.0 1.0 26.2
(DEEP WELL)
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
W rim WIDE DROP CENTRE 24 x W 10 L (#) 254 21.6 658 11.2 LR 24
10.0 0.9 25.9
F 24 x W 12 304.8 25.4 665 14.9 R 24
12.0 1.0 26.2
24 x W 13 330.2 25.4 665 14.9 R 24
H 13.0 1.0 26.2 440/70 R 24
24 x W 9 228.6 25.4 665 11.2 LR 24
diameter
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
15° taper drop centre rims 16.5 x 8.25 209.5 12.7 445 10 R 16.5
(DC - Drop Centre) 8.2 0.5 17.5
16.5 x 9.75 247.7 12.7 445 12 R 16.5
F 9.8 0.5 17.5
19.5 x 14.00 355.5 12.7 521 18 R 19.5
H 14.0 0.5 20.5
20.5 x 16.00 406.5 12.7 546 525/65 R 20.5
A’ 16.0 0.5 21.5
diameter
425/75 R 20
20 x 12.00 DC 304.8 25.4 564 405/70 R 20 (16/70 R 20)
rim
{
9.0 1.5 27.0 14.00 R 24 * TG
24 x 10.00/1.5 254 38 686 395/80 R 24
10.0 1.5 27.0
24 x 11.25/1.3 286 33 676 395/80 R 24
11.3 1.3 26.6
25 x 12.00/1.3 305 33 701 15.5 R 25 * L2 - L3
see note page 99 12.0 1.3 27.6
25 x 13.00/1.4 330 36 707 15.5 R 25 * L2 - L3
13.0 1.4 27.8 17.5 R 25 * L2 - L3
25 x 14.00/1.3 355 33 701 17.5 R 25 * L2 - L3
14.0 1.3 27.6
25 x 14.00/1.5 355 38 711 17.5 R 25 * L2 - L3
14.0 1.5 28.0
5° taper semi drop centre rims 18 - 5.50 F SDC 139.7 22.2 462 7.50 - 18 none
(SDC - Semi Drop Centre) 5.5 0.9 18.2
24 - 8.00 TG SDC 203 35.5 685 13.00 R 24 * TG
8.0 1.4 27.0 14.00 R 24 * TG
24 - 10.00 VA SDC 254 43 700 13.00 R 24 * TG Heupo
10.0 1.7 27.6 14.00 R 24 * TG (OR 2-25)
16.00 R 24 * TG
diameter
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
5° taper bead seat rims 15 - 5.5 139.7 30.5 448 7.50 R 15
(advanced rim) 5.5 1.2 17.6
15 - 6.0 152.4 33 453 7.50 R 15
6.0 1.3 17.8 8.25 R 15
15 - 6.5 165.1 35.6 459 7.50 R 15 none
6.5 1.4 18.1 8.25 R 15
15 - 7.0 177.8 38 429 10.00 R 15
7.0 1.5 16.9 8.25 R 15
diameter
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
5° taper bead seat rims 25 - 10.00/2.0 254 51 737 505/85 R 25
(5 pieces) 10.0 2.0 29.0
25 - 11.25/2.0 (*) 284 51 737 14.00 R 25
11.2 2.0 29.0 16.00 R 25
445/95 R 25
25 - 13.00/2.0 330 51 737 16.00 R 25
13.0 2.0 29.0 445/95 R 25
diameter
F H A’
Rim
Rim types mm mm mm Tyre sizes O-ring
designation
inches inches inches
5° taper bead seat rims 39 - 32.00/4.5 813 114.5 1220 37.5 R 39
(5 pièces) 32.0 4.5 48.0 40.5/75 R 39 Fuodi
39 - 32.00/4.0 813 101.5 1194 40/65 R 39 (OR 3-39)
32.0 4.0 47.0
45 - 36.00/4.5 914 114.5 1372 45/65 R 45 Ref.. 1580
36.0 4.5 54.0 (OR 9.8-45)
49 - 13.00/2.7 330 70 1384 18.00 R 49
diameter
Tube +
Rim Valve type Flap Flap
Fits tyre sizes Tube reference Valve reference valve
diameter (#) reference CAI
CAI
15” 7.50 R 15 15/16 J 570 SC 101106 15x6.00 511268
15x6.00 511268
8.25 R 15 15 K 1221 DC 101126
15x7.50 084220
10.00 R 15 15 P 582 TC 510204
16” 11 LR 16 16 P 15 611 DR 101163 - -
18” 275/80 R 18 (10.5 R 18) KLEBER 438 TR 218A DR 171109 - -
335/80 R 18 (12.5 R 18) KLEBER 444 TR 218A DR 170025
19.5” 18 R 19.5 19.5/20.5 UD 1964 DR 101280 - -
20” 9.00 R 20 20x7.50 818874
20 M 1157 SC 101153
C 20 20x8.50 111005
10.00 R 20 20 N 1158 SC 101161 20x7.50 818874
11.00 R 20
20 P 1158 SC 101173 20x8.50 111005
E 20 Pilote
275/80 R 20 (10.5 R 20)
KLEBER 444 TR 218A DR 170025 - -
335/80 R 20 (12.5 R 20)
12.00 R 20 20 Q 1158 SC 101192 20x8.50 111005
14.00 R 20 20 Q 1158 SC 101192 20x10.0 004489
375/75 R 20 (14.5 R 20)
KLEBER 664 TR 218A DR 171112 - -
405/70 R 20 (14.5 R 20 & 16/70 R 20)
425/75 R 20 (16.5/75 R 20) KLEBER 829 TR 218A DR 751070 - -
16.00 R 20 20 V 576 SC 511937 20x10.00 004489
20.5” 525/65 R 20.5 19.5/20.5 UD 1964 DR 101280 - -
24 R 20.5 20.5 WAMD 1837 (TRJ650) SC 101331 - -
21” 24 R 21 21 WAM 1837 (TRJ650) SC 101333 17-20 551436
22.5” 15 R 22.5 20 S 582 TC 101221
22.5 TAMD 1837 (TRJ650) SC 101853 - -
18 R 22.5
22.5 TD 1964 DR 101863 - -
24” 10.00 R 24
KLEBER 690 TR 218A DR 170036 - -
11.2 R 24
12.00 R 24 24 Q 582 TC 101196 24/25x8.50 001444
13.00 R 24 sur jante DC et SDC
14.00 R 24 TG sur jante DC et SDC KLEBER 703 TR 218A DR 171114 13-24 DR 102902
14.9 R 24
13.00 R 24 sur jante DC et SDC
24 TD 577 SC 101244 13-24 DR 102902
14.00 R 24 TG sur jante DC et SDC
24/25” 14.00 R 24 sur jante plate
13-24/25 551600
15.00 R 24
24/25 T 752 SC 514503
13.00 R 25 24/25x8.50 001444
14.00 R 25 13-24/25 551600
14.00 R 24 sur jante plate
15.00 R 24 13-24/25 S 551601
14.00 R 25 24/25 T AM 1837 (TRJ650) SC 101781
17.5 R 25 16-24/25 551608
16.00 R 24 ** sur jante plate
14-24/25 551604
16.00 R 25 24/25 V AM 1837 (TRJ650) SC 101811
20.5 R 25 17-24/25 551610
16.00 R 24* sur jante SDC 24/25 VD 577 SC 101299 13-24 DR 102902
24/26” 16.9 LR 24
17.5 LR 24
19.5 LR 24 (710) KLEBER TR 218A DR 170042 - -
440/70 R 24 (17.5 LR 24)
500/70 R 24 (19.5 LR 24)
25” 15.5 R 25
25 S AM 1837 (TRJ650) SC 101771 15-24/25 551606
395/80 R 25
18.00 R 25 16-24/25 551608
25 W AM 1837 (TRJ650) SC 101871
23.5 R 25 18-24/25 551612
21.00 R 25 17-24/25 551610
25 YB AM 1837 (TRJ650) SC 101346
26.5 R 25 18-24/25 551612
29.5 R 25 19-25 (8) 102610
(#) DR = straight valve, SC = single bend valve, DC = double bend valve, TC = triple bend valve, see pages 79 to 82
TECHNICAL DATA EARTHMOVER TYRES
77
MICHELIN EARTHMOVER TUBES
Tube +
Rim Valve type Flap Flap
Fits tyre sizes Tube reference Valve reference valve
diameter (#) reference CAI
CAI
26” 18.4 R 26 KLEBER 716 TR 218A DR 170047 - -
28” 16.9 R 28
KLEBER 822 TR 218A DR 170149 - -
19.5 LR 28
29” 26.5 R 29 29 W AM 1837 (TRJ650) SC 101823 19-29 (8) 102620
29.5 R 29
29 YE AM1 1837 (TRJ650) SC 101803 19-29 (8) 102620
33.25 R 29
30” 16.9 R 30 KLEBER 754 170058
TR 218A DR - -
18.4 R 30 & 757 & 170060
33” 18.00 R 33 33 VF AM 1837 (TRJ650) SC 101321 16-33 551760
33.5 R 33 33/35 YE AM 1837 (TRJ650) SC 101833 20-33 551770
34” 18.4 R 34 KLEBER 823 TR 218A DR 170150 - -
35” 24.00 R 35 16-35 551800
29.5 R 35 33/35 YE AM 1837 (TRJS650) SC 101833
33.25 R 35 20-35 551808
37.25 R 35
(#) DR = straight valve, SC = single bend valve, DC = double bend valve, TC = triple bend valve, see pages 79 to 82
TUBE MARKINGS.
example1: 24/25 V AM example2: 25 YB AM
The first two numbers indicate the bead seat (rim) diameter of the tyre into which the tube can be fitted
(in the first example, the tube may be fitted in 24 and 25 inch tyres. In the second example, the tube may be fitted only in 25 inch tyres).
The first letter corresponds to the section width of the tube (internal width of the tyre).
This ranges from A to Z, with A being the smallest, and Z the largest (in the examples above, V and Y indicate that the tubes are designed
for fitting into tyres of relatively large section width).
Sometimes, a second letter provides additional information (example 2) B, E, F and H indicate intermediate widths.
The third and fourth letters are an indication of the valve type.
AM indicates that the tube is fitted with an American valve base: R1946 (TRA SP4000) and a valve stem R1837 (TRJ 650).
D would indicate that the valve is offset. T would indicate a tractor tube fitted with an air-water valve, type TR 218A.
Explanation on valves and valve bases are given on subsequent pages.
FLAP MARKINGS
example: 14-24/25
The first number indicates the total width of the flap when laid flat (includes height of edges), expressed in either mm or in inches.
In the example above, the width of the flap is 14 inches.
The second number indicates the rim diameter, or the tyre bead seat (rim) diameter in inches, with which the flap is to be used.
In this example, the flap may be used with 24 and 25 inch tyres.
Additional letters may be used to provide supplementary information.
For example, the significance of different letters is as follows: L - the edges are tapered,
B - the flap has a reinforcing boss around the valve hole, S - the flap is reinforced, D - offset hole valve.
TECHNICAL DATA EARTHMOVER TYRES
78
SEALS FOR MICHELIN EARTHMOVER TYRES AND RIMS
SEALS DESCRIPTION
O-RING:
Explanation of the sealing ring’s naming process:
- OR: Abbreviation of O Ring
- The second number is the nominal bead seat diameter, expressed in inches.
CORNER SEAL:
Explanation of the corner seal’s naming process:
- The letter indicates the profile of the seal
NOTE:
APPROVAL FOR USE OF CORNER SEALS MUST BE OBTAINED FROM MICHELIN.
TECHNICAL DATA EARTHMOVER TYRES
79
VALVES AND ASSOCIATED ACCESSORIES
FOR EARTHMOVER TYRES AND RIMS
VALVE MARKINGS
The valve is circular and is marked in accordance with ETRTO standards,
starting at the top of the valve, and in the following order:
- NAME (or trademark) of the valve manufacturer and his reference number.
- ETRTO reference number.
valve base
α1 Michelin ETRTO
A α1° α2° α3°
code designation
α3 582 V3-06-5 90 139 139
h
α2
A B C D
D C mm inches mm inches mm inches mm inches
B 20.5 0.81 131 5.16 49 1.93 62.5 2.46
TECHNICAL DATA EARTHMOVER TYRES
80
VALVES AND ASSOCIATED ACCESSORIES
FOR EARTHMOVER TYRES AND RIMS
100 mm
Tyre side
VALVAGE COMBINATION TYPE A4: Comprised of two TYPE A1 valves, both set at 100 mm from the rim edge,
to enable water filling.
Tyre side
Valve mounting
side
TECHNICAL DATA EARTHMOVER TYRES
81
VALVES AND ASSOCIATED ACCESSORIES
FOR EARTHMOVER TYRES AND RIMS
TRA ETRTO A B
α°
code designation mm inches mm inches
TR 618 A V5-01-1 47.5 1.87 - -
TR 621 A V5-02-1 39 1.54 76 2.99 115°
The original valve core holder
can be remplaced by the
TR 622 A V5-02-2 44.5 1.75 117 4.61 90°
ref.1139 TR 623 A V5-02-3 39 1.54 57 2.24 115°
STRAIGHT TR 618A Valves for 15.7 mm (0.6 inch) diameter hole
14 mm hexagon nut
Used with Type A2 rim contour or with SP2 base (may also replace TRJ 670).
TECHNICAL DATA EARTHMOVER TYRES
82
VALVES AND ASSOCIATED ACCESSORIES
FOR EARTHMOVER TYRES AND RIMS
A Rubber sleeve
A
α
B TRJ 693
TRJ 691
Rubber sleeve
A
α
h
TRJ 690
C D
B
VALVE BASE
ACTUAL VALVE AIR AND WATER AGRICULTURAL
(FITMENT WITH TUBE) TYPE VALVE BASE
Allows tyre to be water filled.
Valve with core holder 1139 and plastic nut ref. 1225.
16,6
CONTENTS
This is the only way that tyre pressures can be set accurately for optimum performance.
- use the tables ”Tyre loads and pressures” for TRANSPORT in the earthmover data book.
standard: for machines with a maximum speed between 30 and 60 km/h (19 and 37 mph).
Michelin X-QUARRY: When fitted with 16.00 R 25 X QUARRY, the distance run must not exceed 16 km (10 miles) in one hour.
When fitted with 18.00 R 33, 21.00 R 35 or 24.00 R 35 X QUARRY, the distance run must not exceed 14 km
(9 mph) in one hour.
If the machines are to be used under different speeds or conditions, apply the appropriate load/pressure table (see page 15).
- Specific use
In the case of slow speed use (<30 km/h), or where the cycle length is short (<3 km), cold tyre pressures
may be reduced by up to 10% for the given load in order to improve tyre life and damage resistance.
In the case of increased dynamic load (downhill laden, heavy braking, tight bends, etc), it is recommended
that front cold tyre pressures on rigid dump trucks and scrapers be increased by 10% so long as the maxi-
mum pressure indicated in the tables is not exceeded.
When the tyre is then subjected to important dynamic loading (for example for displacements on site at
maximum speeds higher than 50 km/h), the load will be gradually reduced according to the maximum speed
reached by the vehicle in any point of the operating cycle without change of pressure.
Exceeding this value is likely to result in reduction in tyre life and damage resistance.
example : for the 27.00 R 49, the nominal condition for standard use is 27250 kg at 6,5 bar
For travel speed on site of 65 km/h, the optimal performance would be 23980 kg
(that accounts for 12% of reduction) at 6,5 bar.
If it is not possible to weigh the machine determine the maximum load per tyre on each axle by calculation
or by using the machine manufacturer’s data.
Calculate the load per axle, then determine the tyre weight by
dividing the axle load by the number of tyres per axle.
TECHNICAL DATA EARTHMOVER TYRES
85
TYRES FOR TRANSPORT MACHINES
PROCEDURE FOR DETERMINING INFLATION PRESSURES
Calculate the load per axle, then determine the tyre weight by dividing the axle load by the number of tyres per axle.
III. MOTOR-SCRAPERS
The following data needs to be established:
- The Gross Vehicle Weight (total machine weight in the laden condition).
- The percentage load distribution by axle.
Calculate the load per axle then determine the tyre weight
by dividing the axle load by the number of tyres per axle.
Calculate the load per axle then determine the tyre weight
by dividing the axle load by the number of tyres per axle.
- calculate the load per tyre (in the case of a crane, divide the total weight by the number of axles, and divide by the number of tyre per axle).
Take into account any axle overload (for example: for cranes, overload due to counterweights).
- use the tables “Tyre loads and pressures” for CRANES to determine the tyre pressures.
- In the case of a use of tyres on special machines, please consult us
TECHNICAL DATA EARTHMOVER TYRES
86
TYRES FOR USE IN DESERTS AND SIMILAR CONDITIONS
These tyres are used on machines that are operated in special conditions, such as sand, desert regions, etc.
THE TREAD
The tyre tread is exceptionally broad and has been designed for use in sand. With its track-laying action, free from unwanted movement
within the tyre’s contact area with the ground, the top layer of sand or soil is not broken up. As a result the grip is improved and digging
in of the tyre is minimised.
The flexible casing minimises vibration and the damage which might be caused by driving on washboard (corrugated) surfaces
or bad tracks and is particularly resistant to this type of stress.
This type of casing allows relatively high speeds on roads.
- Secondly, there is a higher load limit for road service where flotation is not an issue.
INFLATION PRESSURE
Three different pressures are indicated. They depend upon the load per axle and working conditions:
- Road:
These pressures are to be applied when the vehicle runs on good roads. This means asphalt or compacted surfaces.
For these conditions the pressures have been calculated for a maximum speed of:
- 65 km/h (40 mph) for the sizes 14.00 R 24 XS, 18.00 R 25 XS TL, 21.00 R 25 XS TL and 21.00 R 25 X RIB TL
- 80 km/h (50 mph) for the sizes 525/65 R 20.5 XS TL, 24 R 20.5 XS TL, 24 R 21 X RIB TL.
- Track:
These pressures are recommended for driving on bad roads, washboard (corrugated surfaces) and gravel or desert surfaces.
For these conditions the pressures have been calculated for a maximum speed of:
- 50 km/h (30 mph) for sizes 14.00 R 24 XS, 18.00 R 25 XS TL, 21.00 R 25 XS TL and 21.00 R 25 X RIB TL
- 65 km/h (40 mph) for sizes 525/65 R 20.5 XS TL, 24 R 20.5 XS TL, 24 R 21 X RiB TL.
- Sand:
At these pressures the XS or X RIB are able to traverse the majority of sand banks.
For these conditions the pressures have been calculated for a maximum speed of:
- 15 km/h (9,3 mph) for sizes 14.00 R 24 XS, 18.00 R 25 XS TL, 21.00 R 25 XS TL and 21.00 R 25 X RIB TL
- 20 km/h (12,5 mph) for sizes 525/65 R 20.5 XS TL, 24 R 20.5 XS TL, 24 R 21 X RiB TL.
After using “sand” pressures, they must be adjusted to the correct pressure for subsequent conditions of use
(road or track).
TECHNICAL DATA EARTHMOVER TYRES
87
DETERMINING INFLATION PRESSURES FOR SURFACE LOADERS
IN REHANDLING, PRODUCTION, EXTRACTION AND FACE WORK
- use the tables “Tyre loads and pressures” for LOADERS to determine the pressure.
Front laden: for the laden front axle. (bucket full)
Rear unladen: for the unladen rear axle. (bucket empty)
It is in this state that the front tyres are most heavily laden.
- determine the maximum load / tyre on the front and rear axles.
Front Axle
The load on the front axle is equal to the total unladen weight of the machine
+ the tipping load. (tipping load is shown in the machine manufacturer’s data)
- use the tables “Tyre loads and pressures” for LOADERS in the earthmover data book under the heading:
Front Tip. load: “tipping load”
EXAMPLE CALCULATION:
For a loader with the following characteristics:
- Base pressures.
Chargeuse AV = 5,0 bar (73 psi)
Chargeuse AR = 2,5 bar (36 psi)
TECHNICAL DATA EARTHMOVER TYRES
88
DETERMINING INFLATION PRESSURES FOR SURFACE LOADERS
IN REHANDLING, PRODUCTION, EXTRACTION AND FACE WORK
IMPORTANT
The rule to determine pressures by calculation applies to loaders of standard specification and which have not been modified
for special use. The calculated pressures are the minimum for the loads and may be increased to obtain a desired level of
handling, or for particular applications, (but must remain within the published load/pressure table for the tyre size and type).
For a given load, it can be necessary to modify the pressure of the tyre in order to optimize the behavior of the loader
(need of more stability for example).
example for improved flotation, decrease front pressure by 0,5 bar (7 psi) (while not decreasing the pressure below 2.5 bar)
for improved stability, increase front pressure by 0,5 bar (7 psi) (without exceeding the authorized maximum pressure)
In case of long travel distances (ex: delivery of new machine, transfer from one site to another, etc.),specific precautions
need to be taken.
For all information, do not hesitate to consult your usual Michelin interlocutor
From a practical point of view, the maximum load on either of the two axles is approximately equal to 2/3 of the machine weight.
HOW TO PROCEED
COMPACT LOADERS
This is the only way whereby tyre pressures can be set accurately for optimum performance.
- determine the maximum load on each tyre on the front and rear axles.
Front axle
The front axle should be weighed with the bucket full and in the transport position.
- use the tables ”Tyre loads and pressures” for LOADER or BACKHOE LOADERS in the data book.
· use the 10 km/h table for the front axle laden (BACKHOE LOADERS)
· use the front laden table for the front axle laden (LOADER)
Rear axle (bucket empty)
The rear axle should be weighed with the bucket empty and in the transport position.
- use the tables “Tyre loads and pressures” for LOADER or BACKHOE LOADERS in the data book.
- use the load table that corresponds to the maximum speed for the rear axle unladen (from 10 to 65 km/h according to the cases)
(BACKHOE LOADERS)
· use the Rear unladen schedule for the rear axle laden (LOADER)
TECHNICAL DATA EARTHMOVER TYRES
89
TYRES FOR WORKING MACHINES COMPACT LOADERS,
BACKHOE LOADERS AND TELESCOPIC HANDLERS FITTED WITH INDUSTRIAL TYRES
BACKHOE LOADERS
- determine the maximum load on each tyre on the front and rear axles.
This is the only way whereby tyre pressures can be set accurately for optimum performance.
Front axle - the front axle should be weighed with the bucket full and in the transport position.
- use the tables “Tyre loads and pressures” for LOADER or BACKHOE LOADERS.
· use the 10 km/h schedule for the front axle laden (BACKHOE LOADERS)
· use the front laden schedule for the front axle laden (LOADER)
Rear axle (bucket empty) - the rear axle should be weighed with the bucket empty and in the transport position.
- use the tables “Tyre loads and pressures” for LOADER or BACKHOE LOADERS.
· use the load schedule that corresponds to the maximum speed for the rear axle unladen
(from 10 to 65 km/h according to the cases) (BACKHOE LOADERS)
· use the Rear unladen schedule for the rear axle laden (LOADER)
- “SIDE-SHIFT”
- the backhoe can be slid along the transversal axis on which it is mounted.
- in the transport position, the load across the rear axle is well distributed.
- “CENTRE POST”
- the backhoe is fixed at the centre, between the two rear wheels;
in the transport position the centre of gravity of the rear axle is offset.
This results in one of the rear tyres being more heavily loaded and the pressure
in it should be adjusted to correspond to the load.
TELESCOPIC HANDLERS
In the case of telescopic handlers the pressures recommended by the machine manufacturer should be used.
These pressures are determined by the machine manufacturer after conducting “Tilt Tests” for stability.
In the absence of machine manufacturer’s recommendation, apply the following pressures.
HOW TO PROCEED
As a general rule, the inflation pressure must never be lower than 2 bar (29 psi)
Should there be an obvious overload or a special need for flotation, or if in doubt:
- weigh the machine to find out the load on each axle or use the loads given by the machine manufacturer.
- use the tables “Tyre loads and pressure” for GRADERS.
For special work (example: sloping embankments), the inflation pressure should never be lower than 2.5 bar (36 psi).
TECHNICAL DATA EARTHMOVER TYRES
90
DETERMINING PRESSURES FOR SKID STEERS (STABIL’X XZSL TYRE)
STABIL’X XZSL TL
HOW TO PROCEED
- determine the maximum load on each tyre by weighing.
This is the only way that tyre pressures can be set accurately for optimum performance.
STL
If it is not possible to weigh the machine, calculate the load on each axle as follows:
Tipping load
1) Calculating the Rear axle load (unladen)
Rear axle load = Static Tipping Load x (l/L)
- use the tables “Tyre loads and pressures for” SKID STEER MACHINES AND COMPACT LOADERS
and apply the “load and carry table”.
- All tyres are inflated to the same pressure, corresponding to the most heavily laden tyre, to ensure good handling.
XF TL
HOW TO PROCEED
- determine the maximum load on each tyre. This is the only way that tyre pressures can be set accurately for optimum performance.
- use the tables “Tyre loads and pressures” for WHEELED EXCAVATORS - 30 km/h for site and for highway service.
At 10 km/h (6 mph) rough terrain pressures can be used where flotation/traction is a required.
However, the tyre pressures must be raised when the machine travels on the highway.
N.B.: Michelin can also offer fitments for machines fitted with truck size tyres in addition to tyres used in singles.
(Example: 8.25 R 20, 9.00 R 20, 10.00 R 20, 11.00 R 20, 12.00 R 20, etc.)
Please consult us for a recommendation.
TECHNICAL DATA EARTHMOVER TYRES
91
DETERMINING PRESSURES FOR COMPACTORS
XLC TYRE
HOW TO PROCEED
The choice of tyre and its working pressure depends on the material to be compacted, the type of work
to be carried out and the operating speed.
Please refer to the information and operating guidelines supplied by the machine manufacturer and use the tables
“Tyre loads and pressures” for COMPACTORS.
HOW TO PROCEED
There are no tyres made specifically for this type of machinery.
Tyres should be chosen according to their average speed capabilities in relation to those of the machine and their load capacity.
All these machines operate at 2 speeds: a “transport” or “travelling” speed and a “work” speed.
When moving at their “transport” speed, (up to 25km/h), the weight carried by the tyres is that of the machine alone.
Once the load per tyre has been determined, refer to the load/pressure table which corresponds best to the speed
at which the selected tyre is to be used.
example: - for a 14.00 R 24 XGLA2,
at a speed of 25 km/h, use the load/pressure table for ”Graders”,
at a speed of 10 km/h, use the load/pressure table for ”Loaders, front laden”.
- for a 18.00 R 25 XVC, use the load/pressure table for “Cranes” at the speed required.
When travelling at their “work” speed (between 1 to 3km/h), the total weight carried by the tyres includes that of the load as well as the
machine itself. Once the load per tyre has been determined, refer to the load/pressure table which corresponds best to the speed at which
the selected tyre is to be used.
example: - for a 14.00 R 24 XGLA2,
use the load/pressure table for “Loaders front tipping”.
- for a 18.00 R 25 XVC,
load/pressure table for “Cranes” at 2 or 5 km/h.
In each case, once the load per tyre has been determined, apply the higher pressure.
In most cases this will be the pressure recommended at “transport” speed.
TRAVELLING MACHINES:
For cold Planers and Stabiliser Mixers: load per axle on pneumatic tyres = 50% of machine weight.
For Pavers: load per axle on pneumatic tyres = 80% of machine weight / number of axles.
LOADED/WORKING MACHINES:
For cold Planers and Stabiliser Mixers: load per axle = 50% of machine weight + payload.
For Pavers: load per axle on pneumatic tyres = 30% machine weight+ maximum load of the container bin / number of axles.
TECHNICAL DATA EARTHMOVER TYRES
92
DETERMINING PRESSURE FOR UNDERGROUND MACHINES
I - TRANSPORT MACHINES
- determine the maximum load on each tyre of each axle, with the machine loaded
- by calculation, using the machine manufacturer’s data, or
- by weighing each tyre position with the machine loaded.
- use the tables “Tyre loads and pressures” for MINE TRANSPORT.
II - LOADERS
There are two methods of determining pressures for a loader.
The load distribution on the front axle of an underground loader is different from that of a surface loader.
The rules for calculating pressures for surface loaders are not applicable.
Use the loads for the Front axle given by the machine manufacturer.
The Qm calculation should theoretically be made for each tyre. However, in practice, specific tyre loads are not normally available and
therefore this leads to the assumption that each tyre on the same axle carries an equal load. When calculating the average load per tyre
on the front and the rear axles, the greatest value of Qm shall be used in TKPH (TMPH) calculation.
In most cases, on two-axle dump trucks, the distribution of the total load of the loaded vehicle (unladen weight + payload) corresponds to
33.3 % on the front axle (single tyres) and 66.7 % on the rear axle (twinned tyres).
When unladen, the front axle is almost always the heaviest.
Thus, the maximum Qm, will nearly always be on the front axle.
Of course, the analysis of the site (or at least, the collected information), weighings and machine characteristics, will provide
the information to define and check the load per tyre.
TECHNICAL DATA EARTHMOVER TYRES
94
TYRES FOR TRANSPORT MACHINES
TKPH (TMPH) METHOD
To obtain the real site TKPH (or TMPH), two more factors must be taken into account:
- the length of cycles exceeding 5 kilometres (or 3 miles)
- the ambient temperature.
The K2 coefficient to apply to the basic site TKPH (basic site TMPH) comes from:
K2 = Vm + [ 0,25* x (TA - TR) ] where Vm is the reference cycle average speed.
Vm TA is the ambient temperature
TR is the reference temperature (38° C or 100° F)
(*: use 0.086 instead of 0.25 when calculating basic site TMPH)
The ambient temperature of the site (TA) to be taken into account is ”the maximum temperature in the shade” during the hottest period.
For temperatures TA greater than 15° C (59° F), use the K2 coefficients shown on page 96.
For temperatures TA lower than 15° C (59° F), use the K2 coefficients shown in the shaded area of the table on page 96.
To sum up, for the real site TKPH (TMPH) calculation, proceed as follows:
- calculate the basic site TKPH (TMPH).
- calculate the correct for cycle length exceeding 5 kilometres (3 miles) by applying the K1 coefficient.
- calculate the correct for ambient temperatures not equal to 38° C (100° F) by applying the K2 coefficient.
Real site TKPH (or TMPH) = Basic site TKPH (or basic site TMPH) x K1 x K2
4 - COMPARISON OF THE TYRE TKPH (TMPH) AND REAL SITE TKPH (TMPH)
On the basis that the choice of tread pattern is made to meet the needs of traction, protection and speed there are 2 possibilities:
a) the tyre’s TKPH (TMPH) is greater than the real site TKPH (TMPH): the tyre is suitable for the application.
b) the tyre’s TKPH (TMPH) is below the real site TKPH (TMPH): the tyre is not suitable for the application.
- Unladen weight per tyre - Front; Qv: 64 = 32 tons 70,6 = 35 short tons
2 2
- Laden weight per tyre - Front; Qc: 301 x 33.3 ~ 50 tons 332 x 33.3 = 55 short tons
(33.3 % of GW on front axle). 2 x 100 2 x 100
- Unladen weight per tyre - Rear; Qv: 57 = 14 tons 62,8 = 15.5 short tons
4 4
- Laden weight per tyre Rear; Qc: 301 x 66.7 ~ 50 tons 332 x 66.7 = 55 short tons
(66.7 % of Gross Vehicle weight on rear axle). 4 x 100 4 x 100
Thus, the value for Qm to be used will be: 41 tons 45 short tons
b) Calculation of Vm
(distance covered per hour)
Vm = L 12 = 16 km in one hour 7.5 = 10 miles in one hour
H 0,75 0,75
d) Calculation of K1 coefficient
The round-trip being longer than 5 kilometres (3 miles), the K1 coefficient is 1.14 (as given in the table on page 96).
e) Calculation of K2 coefficient
The ambient temperature being different from 38° C (100° F), the K2 coefficient is:
K2 = Vm + [ 0,25* x (TA - TR) ]
Vm 16 + [0.25 (36 - 38)] = 0.969 10 + [0.086 (96.8 - 100)] = 0.972
(*: use 0.086 instead of 0.25 for TMPH) 16 10
The choice of tyre available for this site would be between B4 and B types.
Taking into account the abrasive haul roads, the recommendation would be the B4 type (see type definitions on page 04).
TECHNICAL DATA EARTHMOVER TYRES
96
SELECTING THE IDEAL TYRE FOR TRANSPORT MACHINES:
MAIN FACTORS TO BE CONSIDERED AND THE TKPH (TMPH) METHOD
K 1 Coefficients
L (km) L (ml) K1 L (km) L (ml) K1 L (km) L (ml) K1 L (km) L (ml) K1 L (km) L (ml) K1
11 6.8 1.13 21 13 1.19 31 19.3 1.21 41 25.5 1.23
12 7.4 1.14 22 13.7 1.19 32 19.9 1.21 42 26.1 1.23
13 8 1.15 23 14.3 1.20 33 20.5 1.22 43 26.7 1.23
14 8.7 1.16 24 14.9 1.20 34 21.1 1.22 44 27.3 1.23
5 3.1 1.00 15 9.3 1.16 25 15.5 1.20 35 21.7 1.22 45 28 1.23
6 3.7 1.04 16 9.9 1.17 26 16.2 1.20 36 22.4 1.22 46 28.6 1.23
7 4.3 1.06 17 10.6 1.17 27 16.8 1.21 37 23 1.22 47 29.2 1.23
8 5 1.09 18 11.2 1.18 28 17.4 1.21 38 23.6 1.22 48 29.8 1.23
9 5.6 1.10 19 11.8 1.18 29 18 1.21 39 24.2 1.22 49 30.4 1.23
10 6.2 1.12 20 12.4 1.19 30 18.6 1.21 40 25 1.22 50 31 1.23
L = Cycle length in kilometres and in miles.
K 2 Coefficients
Vm Ambient temperature
Km <15 °C 15 °C 17.5 °C 20 °C 22.5 °C 25 °C 27.5 °C 30 °C 32.5 °C 35 °C 37.5 °C 40 °C 42.5 °C 45 °C
(miles) <59 °F 59 °F 63.5 °F 68 °F 72.5 °F 77 °F 81.5 °F 86 °F 90.5 °F 95 °F 99.5 °F 104 °F 108.5 °F 113 °F
10 (6) 0.400 0.425 0.488 0.550 0.613 0.675 0.738 0.800 0.863 0.925 0.988 1.050 1.113 1.175
12 (7) 0.500 0.521 0.573 0.625 0.677 0.729 0.781 0.833 0.885 0.938 0.990 1.042 1.094 1.148
14 (9) 0.571 0.589 0.634 0.679 0.723 0.766 0.813 0.857 0.902 0.946 0.991 1.036 1.080 1.125
16 (10) 0.625 0.641 0.680 0.719 0.758 0.797 0.836 0.875 0.914 0.953 0.992 1.031 1.070 1.109
18 (11) 0.666 0.681 0.715 0.750 0.785 0.819 0.854 0.889 0.924 0.958 0.993 1.028 1.063 1.097
20 (12.5) 0.700 0.713 0.744 0.775 0.806 0.838 0.869 0.900 0.931 0.963 0.994 1.025 1.056 1.088
22 (14) 0.727 0.739 0.767 0.795 0.824 0.852 0.881 0.909 0.938 0.966 0.994 1.023 1.051 1.080
24 (15) 0.750 0.760 0.786 0.813 0.839 0.865 0.891 0.917 0.943 0.969 0.995 1.021 1.047 1.073
26 (16) 0.769 0.779 0.803 0.827 0.851 0.875 0.899 0.923 0.947 0.971 0.995 1.019 1.043 1.067
28 (17) 0.785 0.795 0.817 0.839 0.862 0.884 0.906 0.929 0.951 0.973 0.996 1.018 1.040 1.063
30 (19) 0.800 0.808 0.829 0.850 0.871 0.892 0.913 0.933 0.954 0.975 0.996 1.017 1.038 1.058
32 (20) 0.812 0.820 0.840 0.859 0.879 0.898 0.918 0.938 0.957 0.977 0.996 1.016 1.035 1.055
34 (21) 0.823 0.831 0.849 0.868 0.886 0.904 0.923 0.941 0.960 0.978 0.996 1.015 1.033 1.051
36 (22) 0.833 0.840 0.858 0.875 0.892 0.910 0.927 0.944 0.962 0.979 0.997 1.014 1.031 1.049
38 (24) 0.842 0.849 0.865 0.882 0.898 0.914 0.931 0.947 0.964 0.980 0.997 1.013 1.030 1.046
40 (25) 0.850 0.856 0.872 0.888 0.903 0.919 0.934 0.950 0.966 0.981 0.997 1.013 1.028 1.044
42 (26) 0.857 0.863 0.878 0.893 0.908 0.923 0.938 0.952 0.967 0.982 0.997 1.012 1.027 1.042
44 (27) 0.864 0.869 0.884 0.898 0.912 0.926 0.940 0.955 0.969 0.983 0.997 1.011 1.026 1.040
46 (28) 0.869 0.875 0.889 0.902 0.916 0.929 0.943 0.957 0.970 0.984 0.997 1.011 1.024 1.038
48 (29) 0.875 0.880 0.893 0.906 0.919 0.932 0.945 0.958 0.971 0.984 0.997 1.010 1.023 1.036
50 (31) 0.880 0.885 0.898 0.910 0.923 0.935 0.948 0.960 0.973 0.985 0.998 1.010 1.023 1.035
Vm = number of km (miles) covered per hour.
CONDITIONS OF USE
The range of Michelin industrial tyres has been specifically designed to equip industrial machines .
The sizes are specific to these machines and their work , the loads and speeds correspond to standardized figures .
Each time tyres need to be fitted to mechanical handling equipment , the following rules should be followed:
1°) When the tyre size exists in the industrial tyre range , the industrial tyre must be used .
2°) When the tyre size does not exist in the industrial tyre range, look for a tyre from other tyre ranges
(e.g.: Truck or Earthmover ) ensuring that the condition of use ( speed , load , kilometres in the hour...) are compatible
with the characteristics of the tyre chosen. This can result in certain tyres not being recommended for some uses.
3°) Use of earthmover or truck tyres in mechanical handling conditions follow different rules than those normally applied to these tyres
(speed, load, pressure).
In order to use these tyres in total safety consult Michelin earthmover department who are able to give you the best advice.
TECHNICAL DATA EARTHMOVER TYRES
98
ADVICE ON THE USE OF MICHELIN EARTHMOVER TYRES
Never exceed the inflation pressure for the wheel. (This may be lower than that for the tyre.)
Always ensure that the tyre is well positioned and seated on the rim before inflation to protect the tyre and fitter.
Please consult Michelin technical documentation for advice on inflation pressures and safety guidelines.
If in any doubt, please consult Michelin documents on FITTING AND REMOVING OF EARTHMOVER TYRES.
HANDLING
Poor handling of an unfitted tyre can cause it to be irreparably damaged.
In order to eliminate the risk of bead damage and the problems which could result, we strongly advise that:
1 - The tyre is not lifted directly on the bead with a crane hook.
2 - Flat straps be used (not steel slings or chains).
3 - The tyre be lifted under the tread and not on the beads when a fork lift truck is used.
4 - For all tubeless tyres supplied with bead protectors, the protector should be left in place until the tyre is about to be fitted.
(keep the protectors; they can be refitted when the tyre is temporarily removed for repair or retreading).
STORAGE
In order to avoid premature ageing and damage to tyres, they store them in a cool dry place indoors and away from direct sunlight.
- Tyres should be stored vertically on the roll, one against the other (avoid stacking).
- Tubes, flaps and sealing rings may be stocked in their original packing, or unwrapped, on clear racks, shelves or in containers,
providing that the surfaces in contact with the rubber are smooth to avoid tears, cuts or perforations and free from chemicals
which damage rubber.
TECHNICAL DATA EARTHMOVER TYRES
99
ADVICE ON THE USE OF EARTHMOVER TYRES
Ok No
NOTE: L3** (XKA), L4 (XRD1A) and L5 (XLDD2,* XMineD2, XSMD2+) tyres should only be fitted to multi piece rims.
They should not be fitted to single piece rims.
INFLATION PRESSURE
Appropriate tyre inflation pressure ensures:
- a good tyre/vehicle combination,
- maximum tyre life.
Use the correct pressure (see pages 84 to 92 “How to determine inflation pressure”).
In the absence of any practical advice on tyre loads, working conditions, etc, we can indicate basic working pressures
for most machines based on the machine manufacturer's data.
RECOMMENDATIONS: