Академический Документы
Профессиональный Документы
Культура Документы
Installation guide
For your protection, carefully read these warnings and electrical codes, and the installation instructions
and instructions in their entirety before installing or provided in this document. This professional should
maintaining this equipment. These instructions do be familiar with the construction and operation of
not attempt to cover all installation and maintenance this product and any hazards involved. If not qualified,
Philips EvoKit LED 2x4 and 2x2 situations. If you do not understand these instructions
or if additional information is required, contact your
do not attempt installation. Contact a qualified
electrician.
local Philips representative. Retain these instructions 3 Remove belly pan. If remaining troffer height is 4 Disconnect host fixture ballast from mains.
for maintenance reference. limited, remove ballast.
This installation guide is only valid for the following Philips EvoKit models :
WARNING WARNING Notice
Products 2x4 Products 2x2 Make sure to remove packaging (except the LED
RISK OF FIRE, ELECTRIC SHOCK OR RISK OF PERSONAL INJURY
PERSONAL INJURY protection*), from EvoKit components before
This equipment may have sharp edges. Wear gloves installing.
Do not install in a damaged fixture. to prevent cuts or abrasions when removing from Do not install with total power input greater than
carton, handling and maintaining this equipment. power rating of original fixture.
Install the EvoKit only in NEMA type G or Type NFG When space in the troffer is limited, remove
t-grids with a minimum troffer depth of 3”. original ballast.
Before installation, turn power off. * Remove LED protection just before installing the
Diffuser (E) (see step 14).
WARNING WARNING
Installation of Side Panels (A)
EvoKit 2x4 P 36L xxW 835 2 0-10 7 G2 RISK OF FIRE OR ELECTRIC SHOCK RISK OF FIRE OR ELECTRIC SHOCK
2x2 P 23L 830 1 Mk10 To prevent wiring damage or abrasion, do not expose Luminaire wiring and electrical parts may be damaged For SpaceWise accessory, see Spacewise installation instructions.
2x4 P 32L 835 2 0-10 wiring to edges of sheet metal or other sharp objects. when drilling for installation of LED retrofit kit. Check
36L 840 2 STEP for enclosed wiring and components.
42L 5 Mk10
52L Notice
Do not use abrasive materials, glass cleaners or other solvents on cover plate or lens. To clean the faceplate, use
a mild soap solution. A
Set contains
A Side Panel Do not expose the product to substances and /or materials containing sulphur, chlorine or other halogen A
C B LED Panel compounds and to chemicals mentioned in below table.
2x
A C Troffer Label
D D Closing Panel Category Chemical Name
E Diffuser
Solvents Toluene, xylene, benzene, chloromethane, chloroform, ethyl acetate, butyl
acetate, acetone, MEK, MIBK 5 Install Side panels (A) in-between troffer and T-grid. 6 Slide Side Panel (A) outwards as far as possible.
B Acid HCl, H2SO 4, HNO3
Alkali KOH, NaOH, LiOH, Ca(OH)2
Oil Diesel oil, petroleum, hydro carbons
E
Caution Caution
This kit is designed for permanent installation in Do not make or alter any open holes in an enclosure
Tools required ordinary (Non-Hazardous) locations in accordance of wiring or electrical components during kit
with the National Electrical Code and all applicable installation except if specifically mentioned in these
local codes. Do not use in areas of limited ventilation installation guide.
or in high ambient enclosures.
WARNING
RISK OF PERSONAL INJURY
1 Turn power off and take out original cover. 2 Take out TL tubes. While installing the LED panel (B) and Closing Panel (D), make sure the electrical wiring is not clamped
between panels.
8 Push LED panel upward
into position so that the tabs 90o
2x
sits above the side panels (this W
may require a push up on the
ATTENTION tabs while pushing outward on 2
ESD SENSITIVE the side panels). Fixate panels 1 D
and establish ground by turning X
each fastener 90 degrees. m
90o 15 m
1 max.
Notice
Do not touch the LEDs with 12 Install Closing Panel (D) in-between troffer and 13 Fixate panels and establish ground by turning each 1 Secure 503441 (X) to the back side of LED Panel 2 Drill 1/2” hole in the LED Panel (B) for installation
hands or tooling! Touching T-grid. fastener 90 degrees. (B) using two screws (W). of LED/test switch on indicated area.
LEDs can lead to failure of
the product.
WARNING
RISK OF FIRE OR ELECTRIC SHOCK
Installation Troffer Label (C) While installing the LED panel (B) and Closing Panel (D), make sure the electrical wiring is not clamped between panels.
THIS LUMINAIRE HAS BEEN MODIFIED Remove LED protection Installation Diffuser (E)
FROM ITS ORIGINAL CONFIGURATION. Y violet
THIS LUMINAIRE WILL NO LONGER ACCEPT THE
ORIGINAL LAMPS STATED ON THE RELAMP LABEL. red/white 503441
WARNING EvoKit 0-10V wiring diagram EvoKit MK10 wiring diagram red/white
RISK OF PERSONAL INJURY
Proper grounding of EvoKit metal parts is required yellow white
to ensure personal safety.
0-10V Dimmer MK 10
Notice DIM+ Class 1 Wiring LINE 2 120V / 277V
Make new electrical connections to mains by DIM- } or Class 2 Circuit NEUTRAL
0-10VDC 5 Connect the yellow output wire from the 503441 6 Disconnect black wire and insert white/black
employing applicable connectors in accordance wire (Z) in the EvoKit driver.
to the EvoKit red/white wire connection block and
with the applicable federal, state and local laws, the yellow/black output wire from the 503441 (Z) to
regulations and electrical codes. 16a Optional: For connection EvoKit 0-10V input, use 16b Optional: For connection a dimmer to the EvoKit the EvoKit blue/white wire connection block.
indicated connections on the driver. Mark 10, use indicated connections on the driver.
7a RED
7a Emergency LED driver wiring
CONVERTER
ground in combination with 0-10V and
EvoKit STEP DIM wiring diagram
CONNECTOR RED
Notice WALL SWITCH JUMPER
MK 10 version.
ground HOT WHT/RED WIRE
Emergency
Use 18 AWG Solid Copper Wire Rated>=300V. Strip BLACK
Connect WHT/RED, BLACK and
Wire 3/8” LED
Driver WHITE (2x) wires (Z) as per the
ground In case the EvoKit MK10 277V is installed in COMMON WHITE
503441 wiring diagram.
ground combination with a dimmer, use a minimum of
STEP DIM
WHT/BLK LOAD
LINE S1 LINE 1 2 EvoKits MK10 277V per dimmer.
SELECT Connect the 503441 red to red as
S2 LINE 2 indicated in schematic (Z).
NEUTRAL
B B
BLACK AC DRIVER
10a Situation 1 Grounding: Screw grounding cable 10b Situation 2 Grounding: Connect to the incoming WHITE
from Led Panel (B) to original troffer if host fixture ground lead from conduit. 16c Optional: For connection STEP DIM, use indicated
ground connection is made trough host fixture. connections on the driver.
7b CONVERTER RED
7b Emergency LED driver wiring in
CONNECTOR RED combination with STEP version.
JUMPER
Mains connection Initial installation Philips Advance 503441 Emergency LED HOT BLACK
WIRE
Emergency
Driver (Sold separately) VIOLET VIOLET (+)
LED
11 Connect main cables and hide connected wires BROWN BROWN (-)
WHT/RED Driver
behind LED Panel (B). COMMON WHITE
If the Philips Advance 503441 Emergency LED Driver is to be installed into the EvoKit retrofit fixture, please follow WHT/BLK
BLUE
LOAD
SELECT
these instructions and the instructions provided with the Emergency driver. YEL/BLK
YELLOW
Installation Closing Panel (D) © 2013 Philips Lighting Company. Philips Lighting Company Philips Lighting
X A Division of Philips Electronics North 200 Franklin Square Drive 281 Hilmont Road
SpaceWise: B
efore installing the closing panel connect Spacewise. Y America Corporation. Somerset, NJ 08873 Markham, Ontario
See Spacewise installation instructions. All rights reserved. 1-800-555-0050 Canada, L6C 253
Printed in USA 9/14 1-800-555-0050
Components: Screws (W), Emergency LED driver (X), A Division of
Test switch (Y) Wiring harnass (Z). www.philips.com 443529060851 REV. C Philips Electronics Ltd.
20140519