Академический Документы
Профессиональный Документы
Культура Документы
com
Warranty.
A copy of the specific warranty terms applicable to your Raisecom product and replacement parts
can be obtained from Service Office.
All rights are reserved. No part of this document may be photocopied, reproduced, or translated to
another language without the prior written consent of Raisecom Technology Co., Ltd. The
information contained in this document is subject to change without notice.
Copyright Notices.
No part of this publication may be excerpted, reproduced, translated or utilized in any form or by any
means, electronic or mechanical, including photocopying and microfilm, without permission in
Writing from Raisecom Technology Co., Ltd.
Trademark Notices
Microsoft Corporation.
Contact Information
Technical Assistance Center
The Raisecom TAC is available to all customers who need technical assistance with a Raisecom
product, technology, or, solution. You can communicate with us through the following methods:
Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road,
Haidian District, Beijing 100085
Tel: +86-10-82883305
Fax: +86-10-82883056
You can access the most current Raisecom product information on the World Wide Web at the
following URL:
http://www.raisecom.com
Feedback
Comments and questions about how the RC001-1 device works are welcomed. Please review the
FAQ in the related manual, and if your question is not covered, send email by using the following
web page:
http://www.raisecom.com/en/xcontactus/contactus.htm.
If you have comments on the RC001-1 specification, instead of the web page above, please send
comments to:
export@raisecom.com
20080406 200709
General Safety Instructions
The following instructions serve as a general guide for the safe installation and operation of telecommunications
products. Additional instructions, if applicable, are included inside the manual.
Safety Symbols
This symbol may appear on the equipment or in the text. It indicates potential
safety hazards regarding product operation or maintenance to operator or service
personnel.
Danger of electric shock! Avoid any contact with the marked surface while the
product is energized or connected to outdoor telecommunication lines.
Protective earth: the marked lug or terminal should be connected to the building
protective earth bus.
Some products may be equipped with a laser diode. In such cases, a label with
the laser class and other warnings as applicable will be attached near the optical
transmitter. The laser warning symbol may be also attached.
Please observe the following precautions:
• Before turning on the chassis with optic module, make sure that the fiber optic
cable is intact and is connected to the transmitter.
• Do not attempt to adjust the laser drive current.
• Do not use broken or unterminated fiber-optic cables/connectors or look straight at the
laser beam.
• The use of optical devices with the equipment will increase eye hazard.
• Use of controls, adjustments or performing procedures other than those specified herein, may
result in hazardous radiation exposure.
ATTENTION: The laser beam may be invisible!
Always observe standard safety precautions during installation, operation and maintenance of this
product. Only qualified and authorized service personnel should carry out adjustment, maintenance
or repairs to this product. No installation, adjustment, maintenance or repairs should be performed by
either the operator or the user.
Before operating modules in the electricity conditions, please be noticed that optical modules shall
be connected with optical fiber wires or shield with optical module cover for fear that laser light
harms to operator’s eyes.
RC001-1 is a chassis specially designed for the application of telecommunication carriers, and major
customers in finance, electric power, petroleum industry, and etc. RC001-1 is a 1-slot chassis for 1
communication service module.
RC001-1 is a nonstandard stand-alone device and can be either placed on a table or be fixed on a
19-inch rack using angles specially designed for it. The chassis can adopt both AC and DC power
supply which provide great convenience for customers. Besides, the heat exhaustion design increases
the average smooth operation time of the chassis; the shielding design meets the requirements of
various electromagnetic compatibility indexes; and the steel structure gives the chassis good
durability which enables the chassis to operate in poor physical environment.
1
www.raisecom.com User Manual
RC001-1AC Single-slot, 220V AC 158 x 40 x 200 mm 176V AC ~ 264V AC, 0.5A, 50/60Hz
2
www.raisecom.com User Manual
Slot number: 1
or
DC – -72V DC ~ -36V DC
Ripple: ≤ 100mVp-p
3
www.raisecom.com User Manual
4
www.raisecom.com User Manual
Chapter 5 Installation
1. Fix a service module into RC001-1 and tighten the screws on the service module.
2. When adopting AC power supply, please connect one end of the power supply cable to the
power supply module on the front panel of RC001-1 and the other end to the power supply.
When adopting DC power supply, please correctly connect the power supply cable and ground
cable and then turn on the air switch.
3. Please check whether the power supply cable is well earthed and make sure that protection earth
is well connected with the grounding system.
RC8xx series fiber optic multiplexer Modular PDH multiplexer with 1 or 2 line of
E1 service
RCVS1000 series video fiber optic Single-channel video fiber optic multiplexers
multiplexer
5
Address: 2nd Floor, South Building of Rainbow Plaza, No.11 Shangdi Information Road,
Haidian District, Beijing Postcode: 100085 Tel: +86-10-82883305 Fax: +86-10-82883056
Email: export@raisecom.com http://www.raisecom.com