Академический Документы
Профессиональный Документы
Культура Документы
Electric Screwdrivers
GENERAL CATALOG
Selection Chart
Electric Screwdriver Controller/Counter
Page Series Model Features Starting Method Model Voltage
Bit Grounding
DLV7410A/7410HA/7420A Low Shock
ESD
100/115/220/
5-6 7400A Bit Grounding DLC1110 230/240 V AC
Low Shock
DLV7419A/7419HA/7429A
ESD
Clean Room
7104 DLV7124/7134/7144
Transformerless
Lever Start
DLV8124/8134/8144
8104 Transformerless
12 DLV8154
High Torque Push to Start
Transformerless
8204 DLV8224/8234/8244
High Speed
230 V AC
DLV7530/7540 Torque Reach Light
7500 Torque Reach Light Lever Start
DLV7550
High Torque DLC4511-GGB
13-14 DLV8530/8540 Torque Reach Light DLR1510-JE
8500 DLV8550
Torque Reach Light Push to Start
High Torque
7100 DLV7120/7130/7140 Transformerless
DLV7221 Transformerless
DLV7231/7241 High Speed Lever Start
7200 Transformerless
DLV7251
High Torque
Transformerless
15 8100
DLV8120/8130/8140
Transformerless
115 V AC
DLV8150
High Torque
DLV8221 Transformerless Push to Start
DLV8231/8241 High Speed
8200
Transformerless
DLV8251
High Torque
1
Selection Chart This chart is for reference only.
2
NITTO KOHKI's "Delvo" Electric Screwdrivers are high-quality tools for professional use, with
special emphasis on precise torque control and long life. They always apply just the correct
amount of torque with accurate and positive control at your fingertips. They are smooth and
shockless in operation, too. NITTO KOHKI's customer-oriented service system through our sales
agents ensures that you can use Delvo Electric Screwdrivers with a high degree of reliability.
Shockless
Sophisticated clutches and motor braking mechanism
reduce the shock at the end of the screw tightening
operation and causes less fatigue. Models for EU
DLV7410A/7419A/7410HA/7419HA/7420A/7429A-BME
Long Life DLV7313/7323/7333/7321/7331/7325/7335-CME/CKE
Motor brushes stand over a million tightening cycles. DLV7321/7331-BME/BKE
They can be replaced easily. DLV7319/7329/7339/7349-BME
DLC1213A-GG/GGB/GGU
High Speed
High-speed torque motors cut down screw tightening
time and enhance productivity.
Models for the People’s Republic of China
Safety Standards
DLV7321/7331-CMC
DLC1213-GC
Models with CE Marking (for the European Union) or DLV8124/8134/8144/8224/8234/8244/8154-MJC
CCC (for People’s Republic of China) are available. DLV8124/8134/8144/8224/8234/8244/8154-MKC
DLV7124/7134/7144-MJC
Quieter DLV7124/7134/7144-MKC
DLV5820C/5820HC/5840C
Compare Delvo with a conventional pneumatic DLV5720C/5720HC/5740C/5740HC/5750C
screwdriver, and you will hear the difference. DLC0350GC/0950GC
DLV30/45/70-M C series
DLV30/45/70-SPC(M C) series
DLR5040A-WC
3
Green Procurement
NITTO KOHKI has made every effort in environmental improvement schemes on a company-wide basis
through the implementation of ISO14001 to execute environmentally conscious business activities. As a part
of our ongoing commitment to improve the environment, we are also committed to exclude or reduce
restricted chemical substances in our products, as designated by the RoHS directives and Laws and
Regulations of Chemical Substances in Japan. For further details, please see the following:
4
DLV7400A series For Miniature Screws (1.0 - 2.6 mm)
Features
The light and compact body reduces operator fatigue
• Reduces shock applied to workpieces when fastening screws • The built-in coreless motor achieves reduced inertia
• ESD (electrostatic discharge) protection compliant with IEC61340-5-1 • Torque accuracy is within a top-ranked worldwide level
• Lightweight (Standard type 230 g, Clean room type 275 g) (Based on measurements at our laboratory)
• The Clean Room Type complies with Class 3 Clean Room Rating • Compliant with CE standards
• The controller can adjust speed • Use of the Screw Fastening Counter prevents human fastening
(Screw-fastening speed can be set to suit specific fastening conditions) errors and enhances accurate fastening control (No CE marking
• The controller provides a soft start function or CCC applied)
• The initial speed at screwdriver startup can therefore be slowed • Screw Fastening Counter Model DLR5640-WN works in conjunction
down, effectively preventing screw heads from being scratched with any dedicated SPC-type electric screwdrivers
series
DLV7410HA-BME DLV7420A-BME
DLV7400A
Specifications
Standard Type DLV7410A-BME DLV7410HA-BME DLV7420A-BME
Model
Clean Room Type DLV7419A-BME DLV7419HA-BME DLV7429A-BME
Starting Method Lever Start
Input Voltage 40 V DC
Electric Screwdriver
Input Voltage 100 V AC, 50/60 Hz 115 V AC, 50/60 Hz 220 V AC, 50/60 Hz 230 V AC, 50/60 Hz 240 V AC, 50/60 Hz 230 V AC, 50/60 Hz 240 V AC, 50/60 Hz
Control Function Soft Start, Speed Control, ESD Protected
Plug Shape Asia Asia UK Europe UK Europe UK
Mass (g) 900 2,300
*1: An optional cord is required to connect with this model.
Asia Europe UK
Plug Shape
Neither DLC1213A-GG nor DLC1213A-HE can be used with the DLV7400A series.
Standard Accessories
No. DLV7410A DLV7410HA DLV7420A DLV7419A DLV7419HA DLV7429A
No.0 × 1.8 × 44 1 1 - 1 1 -
Bit
No.0 × 2.5 × 44 1 1 1 1 1 1
No.1 × 4 × 44 - - 1 - - 1
Connection Cable DLW9070 1 1 1 1 1 1
Spring for Low Torque 1 1 - 1 1 -
Suspension Bail 1 1 1 1 1 1
Sleeve for Vacuum DLS2124 - - - 1 1 1
5
For Miniature Screws (1.0 - 2.6 mm)
High Torque
0.45
0.20 Spring 0.40
(black)
Bit Torque (Nm)
series
Shock Waveform Comparison Shock value
between the 7400A series and
Our conventional models
our conventional models
Peak shock value : 33 G
Value of shock applied to the workpiece as DLV7400A series
measured using acceleration pickup. Peak shock value : 8 G
DLV7400A
Time
External Dimensions
Optional Accessories
DLV7410A/7410HA/7420A-BME
165.5
Coupling
Torque Adjustment Ring Torque Adjustment Ring Cover
Forward/Reverse DLW5700 (TD02875)
Lock Nut Changeover Switch
36
Ø32
Ø8
13
Ø8 13.5
Power Lamp
Unit: mm
6
DLV5700 series For Miniature Screws (1.0 - 3.0 mm)
Features
For quality improvement and productivity enhancement
• Grounded bit installation mechanism
• Electro-static discharge (ESD) control
• Low-shock for tightening
(30 % less of standard models)
• Low swing bit mechanism
• Ergonomic design
• High-performance DC motor
• New clutch mechanism
DLV5720/5720H/5740 DLC0350 DLV5740H/5750 DLC0950
Specifications
Model DLV5720 DLV5720H DLV5740 DLV5740H DLV5750
Starting Method Lever Start
Input Voltage 40 V DC 36 V DC
Electric Screwdriver
2
Bit Type (mm)
11
ø4
Mass (g) 230 300
Model DLC0350E DLC0350F DLC0350G DLC0950E DLC0950G
Input Voltage 100 V AC, 50/60 Hz 115 V AC, 50/60 Hz 230 V AC, 50/60 Hz 100 V AC, 50/60 Hz 230 V AC, 50/60 Hz
Asia + Grounding wire U.S.A. UK Asia + Grounding wire
Controller
Plug Shape
DLV5700
Standard Accessories
No. DLV5720 DLV5720H DLV5740 DLV5740H DLV5750
No.0 × 1.8 × 44 1 -
Bit
No.0 × 2.5 × 44 1 1
No.1 × 4 × 44 - 1
Connection Cable
1 1
(1.5 m)DLW9081
Suspension Bail 1 1
Spring for Low Torque 1 -
Spring for
High Torque (black) 0.40 DLV5750 Sleeve Vacuum Pickup
0.15 0.35
DLP5300 (TD04342)
0.30
0.10 0.25 * Please see page 33 for details.
0.20
0.15 Torque Adjustment Ring Cover
0.05
0.04 Spring for 0.10 DLW5700 (TD02875)
0.02 Low Torque (silver) 0.05
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 This minimizes tampering or accidental turning
of the torque adjustment ring once the torque is set.
Torque Scale Torque Scale
External Dimensions
DLV5720/5720H/5740 DLV5740H/5750
188.5
Torque Adjustment Ring Torque Adjustment Ring
165.5 Lever switch 6.5
Holder clamp Holder clamp
Lever switch
38
ø32
36
ø32
7
DLV5800 series For Miniature Screws (1.0 - 2.6 mm)
Features
In response to the needs of cell production system
space-saving DELVO screwdrivers are released.
Controller is designed for emphasis on space-saving size and lightness.
• Clear disengagement of clutch (low-shock mechanism unavailable)
• Grounded bit installation mechanism
• ESD (electrostatic discharge) protection
• New lever is adopted
• Low swing bit mechanism
• Low voltage transless controller
DLC0250E
DLV5820/5820H/5840
DLC0350
Specifications
Model DLV5820 DLV5820H DLV5840 Model DLC0250E
series
Starting Method Lever Start Input Voltage 100 V AC, 50/60 Hz
Input Voltage 40 V DC Function Grounded Bit Installation Mechanism
Torque Adjustment Stepless Mass (g) 300
Torque (Nm) 0.02 - 0.2 0.15 - 0.4
Electric Screwdriver
U.S.A.
Controller
Free Speed (min-1) 750 1,000 600
Power Consumption (W) Approx. 10
Screw Size Machine Screw 1.0 - 2.3 1.6 - 2.6
(mm) Tapping Screw 1.0 - 2.0 1.4 - 2.3 Plug Shape
3.5
2
DLV5800
Grounding Bit Feature Equipped as standard
(black)
Optional Accessories 0.15 0.30
0.10 0.20
0.15
0.05 0.10
Sleeve Vacuum Pickup Spring for
0.04
DLP5300 (TD04342) Low Torque (silver)
0.02
* Please see page 33 for details.
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
Torque Scale Torque Scale
Torque Adjustment Ring Cover
DLW5700 (TD02875)
External Dimensions
108
DLV5820/5820H/5840 DLC0250E
Connection cable
1.5 m
Torque Adjustment 165.5
Ring
Lever switch
68
Holder clamp
DLC0250E
36
ø32
DLV5840
No.123456
Unit: mm
8
DLV7300 series For Miniature Screws (1.0 - 3.5 mm)
Features
• The dedicated controller realizes high-accuracy screw
tightening
• High repeatable torque accuracy
• The controller provides a soft start function. The initial
speed at screwdriver startup can therefore be slowed
down, effectively preventing screw heads from being
scratched.
• Variable speed adjustment enables to select optimum
screw tightening speed.
• DLV7325, DLV7335 meet Class 5*1 Clean Room
standards
*1: Based on Nitto's standard of measurement
DLV7313/7323/7333 DLV7321/7331 DLV7325/7335 DLC1213A
DLV7325-CKE DLV7335-CKE
Electric Screwdriver
3.5
as option. See page 31 for details Optional Accessories
2
23 6.35
ø7
DLW5500 (TD00333)
Model Features Input Voltage Control Function Plug Shape Mass(kg)
This minimizes tampering or accidental turning
DLC1213A-EN Standard 100 V AC, 50/60 Hz of the torque adjustment ring once the torque is set.
Asia
DLC1213A-FE*3 Standard 115 V AC, 50/60 Hz
DLC1213A-GE Standard 220 V AC, 50/60 Hz Soft start, UK
Controller
0.8
Asia Europe UK
Plug Shape
0.6 DLV
7321/7323/7325
0.4
No.1 × 4 × 44 - 1 - - 1 - -
No.1 × 7 × 50 - - - 1 - - -
No.2 × 4 × 44 - - 1 - - 1 - DLC1213A
No.2 × 4.5 × 50 - - - - - - 1 143 145
No.2 × 7 × 50 - - - 1 - - -
DLS2124 - - - - 1 - -
DLS2127 - - - - 1 1 -
Sleeve
Pilot
102
DLS2130 - - - - 1 1 - Lamp
DLS2134 - - - - - 1 -
DLS2135 - - - - - - 1
Receptacle Cord 2 m
Suspension Bail 1 Power Switch
Plug
Speed Adjustment Knob Soft-Start Adjustment Knob
External Dimensions
DLV7313/7323/7333 DLV7321/7331 DLV7325/7335/7319/7329/7339
DLV7313 : 215 DLV7323 / 7333 : 225 215 247
Forward / Reverse 36 Nozzle for Connection
Changeover Switch Lever Switch Lever Switch Vacuum Pump
ø32
ø32
ø30
ø34
40
Cord Cord
1.5 m 1.5 m
Torque Forward / Reverse Sleeve Forward / Reverse
ø40
ø40
Plug Torque
5
9
DLV7300-BME/BKE series For Miniature Screws (1.0 - 3.5 mm)
Features
Workpiece-conscious electric screwdrivers
• Statistic electricity buildup is prevented to protect workpieces
from electrostatic discharge
• Minimal impact in screw tightening protects workpieces from
damaging and enables stable screw tightening
• ESD (electrostatic discharge) protection compliant with
IEC61340-5-1
series
• Meet Class 5*1 or more Clean Room standards
*1: Based on Nitto’s standard of measurement
DLV7300-BME/BKE
ESD ESD / Low Shock
Bit Shank:ø4 mm DLV7321-BME*2 DLV7331-BME*2 DLV7319-BME*2 DLV7329-BME*2 DLV7339-BME DLV7349-BME*2
Model (for reference)
Bit Shank:Hex. 6.35 mm DLV7321-BKE DLV7331-BKE
1.2
Starting Method Lever Start DLV7349
Input Voltage 36 V DC
Torque Adjustment Stepless 1.0
Torque (Nm) 0.05 - 0.5 0.3 - 1.2 0.2 - 0.4 0.25 - 0.55 0.45 - 0.95 0.55 - 1.2
Electric Screwdriver
DLV
For BME
0.3 DLV7319
11
ø4
Torque Scale
Mass (g) 350 400
*2 : These models are made to order.
Static Electricity (V) 350 5 Handle Lever Switch Synthetic resin with carbon fiber
Handle
Surface Resistance ( ) more than 1013 104 Power Cable Anti-static material
Static Electricity (V) 350 2
Lever Switch * Measurement conditions (Temperature:22 ℃ Humidity:66 %)
Surface Resistance ( ) more than 1013 104
•
(1) Static electricity Earth the measurement equipment and measuring person.
Forward / Reverse Switch Static Electricity (V) 25 2 • Grip the screwdriver five times using Ansel Edmont electronic control glove.
No.1 × 4 × 44 1 - 1 - -
ø32
ø40
Power Cable
1.5 m
No.1 × 7 × 50 - - - - 1
Screw Suction Sleeve
No.2 × 4 × 44 - 1 - 1 - Forward/Reverse Changeover Switch
No.2 × 7 × 50 - - - - 1
DLS2124 1 - - - - DLC1213A- B
Sleeve
DLS2130 1 1 - - -
DLS2134 - 1 - - - Pilot
102
Lamp
Suspension Bail 1
Receptacle Power Switch Power Cable 2 m
Speed Control Volume Soft Start Adjustment Volume Unit: mm
10
DLV7000/8000 series For Miniature Screws (1.0 - 3.5 mm)
Features
100 / 115 V AC Direct Transformerless Precision Miniature Screw Type
• A built-in controller model saves space and facilitates layout change
• High repetitive torque accuracy
• Available with lever type (DLV7000 series) for each screw alignment
and push to start type (DLV8000 series) for rapid screw tightening
• The high-speed type (DLV7031/8031) available at 1,200 min-1 for
improving work efficiency (100 V AC only)
series
2
Bit Type (mm)
11
ø4
-
No.1 × 4 × 44 1 -
DLV7030
No.2 × 4 × 44 - 1 /8030
Suspension Bail 1
Bit Torque (Nm)
1.0 DLV7031
/8031
Optional Accessories
DLV8020
Torque Adjustment Ring Cover
0.5
DLW5300 (TD00332)
This minimizes tampering or accidental turning DLV7020
of the torque adjustment ring once the torque is set.
0
1 2 3 4 5 6 7
Torque Scale
External Dimensions
DLV7020/7030/7031 DLV8020/8030/8031
Cord 3 m Cord 3 m
Forward/Reverse Changeover Switch Forward/Reverse Changeover Switch
44
32
32
44
Lever Switch
240
236
Torque Adjustment Ring
Torque Adjustment Ring
Unit: mm
11
DLV7104/8104/8204 series For Machine Screws (2.6 - 6.0 mm)
Features
The most popular models have been redesigned
• Equipped with bit grounding mechanism
• Long-life cam is utilized
• The clear plastic torque adjustment ring cover minimizes
series
unintentional tampering of the preset torque
• The changeover switch enables operators to change forward/reverse
rotation with a single hand
• The ergonomically designed grip can be held tightly to resist
against tightening reaction force, resulting in reduced operator
fatigue
DLV7104/8104/8204
series
MKH MKH MKH MKH MKH MKH MKH MKH MKH MKH
Starting Method Lever Start Push to Start
Input Voltage 230 V AC, 50/60 Hz
Torque Adjustment Stepless
Torque (Nm) 0.25 - 0.75 0.5 - 1.7 1.2 - 3.0 0.25 - 0.75 0.5 - 1.7 1.2 - 3.0 2.0 - 4.5 0.35 - 0.7 0.5 - 1.7 1.2 - 3.0
Free Speed (min-1) 900 600 900 600 400 2,000 1,800 1,100
Power Consumption (W) 35 45
Screw Size Machine Screw 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 4.5 - 6.0 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0
(mm) Tapping Screw 2.3 - 3.0 2.3 - 3.5 3.0 - 4.0 2.3 - 3.0 2.3 - 3.5 3.0 - 4.0 4.5 - 5.0 2.3 - 3.0 2.3 - 3.5 3.0 - 4.0
Mass (g) 720 710 910 710
14
23 9 6.35
ø7
24 5
ø6
unit : mm
4.5 4.5
4.0 4.0
154
V8
Bit Torque (Nm)
3.5 3.5
DL
3.0 3.0
14 4
44/8 4
824
2.5 2.5
71 DLV
Standard Accessories 2.0 DLV 2.0
134 234
134/8
1.5 1.5
For MJE/MJH
• Bit No.1 × 6 × 70: 1 pc. • Spare Carbon Brush: 2 pcs.
DLV7 DLV8
• Bit No.2 × 6 × 70: 1 pc. • Suspension Bail: 1 pc. 1.0 1.0
DLV7124/8
124 DLV8224
0.5 0.5
• Bit No.1 × 7 × 75: 1 pc. • Spare Carbon Brush: 2 pcs.
For MKE/MKH 0 0
• Bit No.2 × 7 × 75: 1 pc. • Suspension Bail: 1 pc. 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9
• Bit No.2 × 7 × 75: 1 pc. • Spare Carbon Brush: 2 pcs. Torque Scale
For 8154-MKE/MKH
• Bit No.3 × 7 × 50: 1 pc. • Suspension Bail: 1 pc.
External Dimensions
DLV7124 / 7134 / 7144 DLV8124 / 8134 / 8144 / 8224 / 8234 / 8244 DLV8154
263 264 264
Changeover Changeover 51 134
Brush Holder Brush Holder
Switch Switch
ø39.5
Bit Cord 3 m
1
5
9
3
7
ø39.5
ø50
ø50
24
40
unit: mm
12
DLV7500/8500 series For Machine Screws (2.6 - 6.0 mm)
Features
Low vibration, low noise, and easy gripping in a compact design
• The easily visible torque reach light goes on when the set torque is reached
• The combination of an advanced clutch design and the auto-stop circuit assures torque accuracy
• The long life motor with a yoke made of advanced materials further assures a long service life
• Compliant with CE standard
• ESD (electrostatic discharge) protection compliant with IEC61340-5-1 (BKE models)
series
DLC4511-GGB
DLR1510-JE
Static Electricity (V) 350 5 Handle Lever Switch Synthetic resin with carbon fiber
Handle
Surface Resistance ( ) more than 1013 104 Connection Cable Anti-static material
Static Electricity (V) 350 2
Lever Switch * Measurement conditions (Temperature:22 ℃ Humidity:66 %)
Surface Resistance ( ) more than 1013 104
•
(1) Static electricity Earth the measurement equipment and measuring person.
Forward / Reverse Switch Static Electricity (V) 25 2 • Grip the screwdriver five times using Ansel Edmont electronic control glove.
No.2 × 7 × 75 1 1
No.3 × 7 × 50 - 1
Spare Carbon Brush 2
Connection Cable 1
Lever Switch Cord 3 m
Suspension Bail 1
DLV8500 series
257
ø39.5
55
ø50
Unit: mm
13
For Machine Screws (2.6 - 6.0 mm)
4.0
DLV7550/8550
Bit Torque (N m )
3.0
DLV7540/8540
2.0
series
1.0
DLV7530/8530
1 2 3 4 5
Torque Scale
Specifications
Model DLC4511-GGB DLR1510-JE
Stepless speed adjustment 80 - 100 % Screw counting: OK lamp and buzzer for notification
Soft start: adjustable time setting of slow speed (max. 3 sec.) Variable non-operation time
Function External output signals: start and torque up Setting protection by key lock switch
Electro-static discharge(ESD) control Setting by touch switch for easy operation
DLV7500/8500
External output signals: Start, Torque up, Count up & Cycle OK
Controller
Plug Shape
External Dimensions
DLC4511-GGB DLR1510-JE
Number
Setting/Counting,
Time Setting Display
Soft Start
OK
Adjustment
Volume
SPEED
MODE SELECTION (-)DOWN (+)UP RESET
HIGH
126
LOW
77.5
81.5
SOFT START
SLOW
SET
ÇR
QUICK
LOCK
ÇT
Receptacle
3 +
5 -
Power Swich
Receptacle
Key Lock Swich
Power Switch
Terminal Block
1 2 3 4 5
Output Terminal
1 2 3
Fuse Holder
R
Unit: mm
14
DLV7100/7200/8100/8200 115V series For Machine Screws (2.6 - 6.0 mm)
series
DLV7100/7200/8100/8200(115V)
DLV7100/ DLV8100/
7200 series 8200 series DLV7251 DLV8150/8251
Features
Long Time Selling, Reliable, and High Performance
• Transformerless space saving model built in automatic stop circuit • The high speed type DLV7200 / 8200 series enhances working
• Combination of unique clutch mechanism and automatic stop efficiency
circuit maintains high repetitive torque accuracy • The high torque type DLV7251 / 8150 / 8251 series is equipped
• The lever start type DLV7100 / 7200 series is suited for with a grip, which is useful for tightening big screws like 6 mm
temporarily tightening screws and tightening screws set at angles machine screws
• The DLV8100 / 8200 series is push to start type for continuous
screw tightening
Specifications Standard High Speed High Torque Standard High Torque High Speed High Torque
Bit Shank: DLV7120- DLV7130- DLV7140- DLV7221- DLV7231- DLV7241- DLV8120- DLV8130- DLV8140- DLV8150- DLV8221- DLV8231- DLV8241-
Hex. 5 mm FJE FJE FJE FJE FJE FJE FJE FJE FJE FJE FJE FJE FJE
Model
Bit Shank: DLV7120- DLV7130- DLV7140- DLV7221- DLV7231- DLV7241- DLV7251- DLV8120- DLV8130- DLV8140- DLV8150- DLV8221- DLV8231- DLV8241- DLV8251-
Electric Screwdriver
Hex. 6.35 mm FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE FKE
Starting Method Lever Start Push to Start
Input Voltage 115 V AC, 50/60 Hz
Torque Adjustment Stepless
Torque (Nm) 0.25 - 0.75 0.5 - 1.7 1.2 - 3.0 0.35 - 0.7 0.5 - 1.7 1.2 - 3.0 2.0 - 4.5 0.25 - 0.75 0.5 - 1.7 1.2 - 3.0 2.0 - 4.5 0.35 - 0.7 0.5 - 1.7 1.2 - 3.0 2.0 - 4.5
Free Speed (min ) 900
-1
900 600 1,800 1,800 1,100 700 900 900 600 400 1,800 1,800 1,100 700
Power Consumption (W) Approx. 35 Approx. 45 Approx. 35 Approx. 45
Screw Size Machine Screw 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 4.5 - 6.0 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 4.5 - 6.0 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 4.5 - 6.0
(mm) Tapping Screw 2.6 - 3.0 2.3 - 3.5 3.5 - 4.0 2.6 - 3.0 2.3 - 3.5 3.0 - 4.0 4.5 - 5.0 2.6 - 3.0 2.3 - 3.5 3.5 - 4.0 4.5 - 5.0 2.6 - 3.0 2.3 - 3.5 3.0 - 4.0 4.0 - 5.0
Mass (g) 700 700 890 690 890 690 890
For FJE For FKE Asia
Plug Shape
Bit Type (mm)
14
23 9 6.35
ø7
24 5
ø6
No. FJE FKE except DLV7251 / 8150 / 8251-FKE DLV7251 / 8150 / 8251-FKE
Bit Torque (Nm)
No.2 × 6 × 70 1 - - DLV
7130/7231/
No.2 × 7 × 75 - 1 1 8130/8231
No.3 × 7 × 50 - - 1
1.5
Spare Carbon Brush 2
DLV7120/
Suspension Bail 1 8120
DLV7221/8221
0
1 2 3 4 5 6 7 8 9
Torque Scale
External Dimensions
DLV7120/7130/7140/7221/7231/7241 DLV8120/8130/8140/8221/8231/8241
Lever Switch
265 266
79 134 52 79 134 52
40
ø39.5
ø39.5
Forward/Reverse
Suspension Bail Forward/Reverse Changeover Switch Changeover Switch
Cord 3 m
Changeover Switch
ø39.5
ø39.5
ø50
Cord 3 m Cord 3 m
Pistol Grip
140
24
24
Cross Section
40 40 Unit: mm
Cross Section
15
Multiple Controllers For DLV7300 series
Multiple Controllers
Model DLE3610A-EN
Input Voltage (Primary Side) 100 V AC, 50/60 Hz
Secondary Output 24 V AC, 50/60 Hz, 15 A
Capacity 360 VA
External Dimensions (mm) W190 × H134 × D188
U.S.A. DLE3610A AC Power Supply Scotch Lock
AC Input (Connecting terminal)
Plug Shape
15 m 15 m
Extension Cord
Mass (kg) 9 DLC2310 24 V AC
Accessories Two 15 m extension cords Controller Connection
Model DLC2310-CE / DLC2310-CN Cord DLV7313
Input Voltage (Primary Side) 24 V AC, 50/60 Hz Connection DLV7321 / 7331
Secondary Output 36 V DC, 2 A Terminal DLV7323 / 7333
External Dimensions (mm) W74 × H42 × D118 Max. 12 Max. 12 DLV7325 / 7335
Mass (kg) 0.36 Max. 24 Screwdrivers Screwdrivers
Two 0.5 m connection cords
Accessories and two scotch locks
(Connecting terminal)
Plug Shape
16
DLV02/12/16 series For Machine Screws (1.0 - 4.2 mm)
Features
Brushless motors are incorporated for maximum tool life
• Ergonomic grip offers greater operator comfort and
increased maneuverability
• Grounded bit system standard
• Clear plastic torque adjustment cover provided as standard
accessory (DLV02/12/16SL-CKE)
• ESD (electrostatic discharge) protection (DLV02/12/16SL-BKE)
• Compliant with CE standards
• Controllers feature an overload detection function. When an
overload is detected, the controller stops the screwdriver.
Operation can be resumed after the screwdriver is unloaded,
and the lever released (DLC16S)
• Universal input voltage from 100 to 240 V AC for easy
series
installation (DLC16S)
• Variable speed adjustment enables you to select optimum
screw tightening speed (DLC16S)
Specifications
Model Standard DLV02SL-CKE DLV12SL-CKE DLV16SL-CKE Model DLC16S-WGB
ESD DLV02SL-BKE DLV12SL-BKE DLV16SL-BKE Input Voltage 100 - 240 V AC, 50/60 Hz
Starting Method Lever Start Output Voltage 20 - 30 V DC
Input Voltage 20 - 30 V DC Function Speed Control
Controller
Electric Screwdriver
1.6
Standard Accessories 1.4
DLV16
Bit Torque (Nm)
0.4
DLV02
0.2
0
1 2 3 4 5 6 7 8 9 10
Torque Scale
External Dimensions
DLV02/12/16SL-CKE DLC16S-WGB
ø40
ø38
ø37
ø34
150 12.5
46.3
Torque Scale
65
Power Lamp
235.5
ø38
ø34
ø28
0
2
4
6
8
10
Torque Scale
Torque Adjustment Ring Cover
Lever
ø41
Bit
23.5 Foward/Reverse Changeover Switch 3.5 Suspension Bail
235.5
Unit: mm
17
DLV30/45/70 series For Machine Screws (2.6 - 8.0 mm)
Features
Eco-friendly electric screwdrivers with built-in brushless motors
in a transformerless profile
・Torque range from 0.4 to 7.0 Nm
・Speed range from 650 to 2,000 min-1
・Both the Lever Start and Push to Start types of models are avilable
・Equipped with a torque adjsutment ring cover
・Design confroms to the RoHS Directive and thus appeals to the
environmentally conscious user
・Models with CE marking are available
・Easily detachable Pistol Grip DLW2300 (TD00335) comes with the DLV30SL DLV30SP DLV45SL DLV70LP
unit as a standard accessory (DLV45/70 series)
Specifications
series
Low Speed Standard High Speed Low Speed Standard High Speed Low Speed Standard Low Speed
DLV30LL- DLV30SL- DLV30HL- DLV30LP- DLV30SP- DLV30HP-
MKG MKG MKG MKG MKG MKG DLV45LL- DLV45LP- DLV45SL- DLV45SP- DLV70LL- DLV70LP-
European Plug*1
DLV30LL- DLV30SL- DLV30HL- DLV30LP- DLV30SP- DLV30HP- MKG MKG MKG MKG MKG MKG
MJG MJG MJG MJG MJG MJG
Model
DLV30LL- DLV30SL- DLV30HL- DLV30LP- DLV30SP- DLV30HP-
Electric Screwdriver
MKE MKE MKE MKE MKE MKE DLV45LL- DLV45LP- DLV45SL- DLV45SP- DLV70LL- DLV70LP-
USA Plug
DLV30LL- DLV30SL- DLV30HL- DLV30LP- DLV30SP- DLV30HP- MKE MKE MKE MKE MKE MKE
MJE MJE MJE MJE MJE MJE
Starting Method Lever Start Push to start Lever Start Push to start Lever Start Push to start Lever Start Push to start
Free Speed (min-1) 650 1,200 2,000 650 1,200 2,000 650 1,200 650
Input Voltage 230 V AC, 50/60 Hz
Torque (Nm) Low Torque Spring* 3 0.4 - 1.6
2
2.0 - 4.5 3.8 - 7.0
High Torque Spring* 1.2 - 3.0
DLV30/45/70
Power Consumption (W) Approx. 45
Screw Size Machine Screw 2.6 - 5.0 4.5 - 6.0 6.0 - 8.0
(mm) Tapping Screw 2.5 - 4.0 4.0 - 5.0 4.5 - 6.0
Mass (g) 700 870 (with Pistol Grip)
For MKG/MKE For MJG/MJE
Bit Type (mm)
14
Torque Diagram (for reference)
23 9 6.35
ø7
24 5 8.0
ø6
DLV70
For MKG/MJG For MKE/MJE 7.0
Europe U.S.A.
Plug Shape
6.0
Bit Torque (Nm)
5.0 DLV45
4.0
*1 : MKG/MJG type has CE marking *2 : Standard Accessory *3 : Built-in. DLV30
3.0
Standard Accessories High Torque Spring
DLV30 series DLV45/70 series 2.0
No. MJG/MJE MKG/MKE MKG/MKE
No.2 × 6 × 70 1.0 DLV30
Bit
1 - -
No.2 × 7 × 75 - 1 1 Low Torque Spring
Suspension Bail 1 1 2 3 4 5 6 7 8 9
Low Torque Spring 1 - Torque Scale
External Dimensions
DLV30LL/30SL/30HL DLV30LP/30SP/30HP
Torque Adjustment Ring Torque Adjustment Ring
Cord(3 m) Cord(3 m)
Torque Scale Torque Scale
Bit Bit
1
5
9
1
5
9
3
7
3
7
ø39.5
ø39.5
Torque Ajustment
51
Torque Ajustment
51
Foward/Reverse Foward/Reverse
Ring Cover Ring Cover Changeover Switch
Changeover Switch
48.5
46.5
49.8
50
3
7
3
7
1
1
5
Foward/Reverse
46
46
ø39.5
51
51
276 274
50 48
50
140
40 40
unit: mm
18
DLV30/45/70-IKE series For Machine Screws (2.6 - 8.0 mm)
Features
Incorporates long-life brushless motors
• The newly designed clutch mechanism offers precise
torque repeatability over sustained periods of use
• Three series of screwdrivers: DLV30/45/70-IKE can be
operated by one standard control unit giving you wide
screw tightening torque coverage from 0.4 to 7.0 Nm
and maximum free speeds of 650, 1,200 or 2,000 min-1
• Compliant with CE
series
Specifications
Series DLV30 Series DLV45 Series DLV70 Series
Model Lever Start DLV30LL-IKE DLV30SL-IKE DLV30HL-IKE DLV45LL-IKE DLV45SL-IKE DLV70LL-IKE
Push to Start DLV30LP-IKE DLV30SP-IKE DLV30HP-IKE DLV45LP-IKE DLV45SP-IKE DLV70LP-IKE
Input Voltage 40 V DC
Low Torque Spring 0.4 - 1.6
Torque (Standard Accessory) 2.0 - 4.5 3.8 - 7.0
Adjustment (Nm)
Electric Screwdriver
0-2
*1Free Speed at Soft Start (min-1) 260 480 800 260 480 260
Screw Size (mm) Machine Screw 2.6 - 5.0 4.5 - 6.0 5.0 - 8.0
Tapping Screw 2.5 - 4.0 4.0 - 5.0 4.5 - 6.0
Mass (g) 720 870 (with Pistol Grip)
3.5 7.0
Bit Torque (Nm)
3.0 6.0
High Torque Spring
2.5 5.0 DLV70
2.0 4.0
DLV30
1.5 3.0
DLV45
1.0 2.0
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7
Torque scale Torque Scale
External Dimensions
DLV30LL/30SL/30HL-IKE DLV30LP/30SP/30HP-IKE
Torque Adjustment Ring Torque Adjustment Ring
Torque Scale Torque Scale
Bit Bit
1
5
9
1
5
9
3
7
3
7
Ø39.5
Torque Ajustment
Ø39.5
51
48.5
46.5
50
50
274 276
Lever Power cord(3 m) Power cord(3 m)
DLV45LL/45SL/70LL-IKE DLV45LP/45SP/70LP-IKE
Torque Adjustment Ring Torque Adjustment Ring
Bit Torque Scale Torque Scale
Bit
Ø42
Ø42
Torque Ajustment
Ø39.5
Foward/Reverse
46
Torque Ajustment
Ø39.5
46
Foward/Reverse
51
51
58.5 60.5
Lever
24
24
40 40 Unit: mm
19
DLR70S-WGB Screw Fastening Counter for DLV30/45/70-IKE series
Features
Enhanced versatility by combining controller and counter
• This model has a “Count Correction” function that does not count alien screws
with different length, refastened screws that were initially fastened sufficiently,
or incompletely fastened screws that were fastened in a slanting direction or
stopped fastening in midcourse
• “Count Back” function reverses the counting when a screw is unfastened
• Up to four different screw fastening programs can be stored in the internal
memory for a wide variety of assembly work
• Sequential screw tightening system (Link Function) can be built up with up to
10 screwdriver/controller sets connected in series
• Equipped with “Stepless Speed Adjustment” function and “Soft Start” function
• Universal input voltage from 100 to 240 V AC for convenient installation
DLR70S-WGB
sequence. Only when the first screw fastening is finished, can the next Output Voltage 40 V DC
screwdriver change from standby to ready. When the last fastening in the Speed Control Function 60 - 100 %
sequence is finished, the first screwdriver is once again ready and the Soft Start Function 0 - 2 sec.
sequence can be repeated again. Count 0 - 99
N.B. Up to 10 screwdriver/counter sets can be connected to the LINK.
Allowable Number of Screw
Fastening Programs 4
A B A B A B
F F F
OK / NG / LINK-OUT / TORQUE UP
C/M C/M C/M
SPEED
MAX
SOFT
START
QUICK
SPEED
MAX
SOFT
START
QUICK
SPEED
MAX
SOFT
START
QUICK
Output Signal
Mass (kg) 2.1
Size W × L × H (mm) 117 × 325 × 76
9 9 9
Europe
Plug shape
External Dimensions
117
Predicted fastening
Depth: 325
OK/NG judge LED indicator
time LED
Fastening count / External connection
Work set LED terminal block
indicator setting display
OK/NG COUNT
1 2 3 4 5 6 7 8 9 10 11 12 13 14
SCREW COUNTER
WORK TIMER
DRIVER
A B ON
76
20
DLC70S-WGB Controller for DLV30/45/70-IKE series
Features
Universal input voltage from 100 to 240 V AC for convenient installation
• The controller provides soft start function. The slow startup prevents
screw heads from possible damage caused by the disengaged bit.
• Stepless speed adjustment function widens the speed range from 390
to 2,000 min-1 for various applications
• The controller outputs: Start, torque-up and reverse is via a dry contact
method. These signals can be used for counting up tightened screws
and preventing screw tightening errors.
• Applying 24 V DC to the designated terminals on the controller brings
the screwdriver to an immediate stop in emergency cases
• Can be installed either horizontally or vertically
Specifications
Model DLC70S-WGB
DLC70S-WGB
1
-
+
POWER
OFF
ON
Size W × L × H (mm) 132 × 297 × 67
Bit Grounding Ready(With a 1M Ω resistor)
SLOW
LOW
SOFT START
SPEED
HIGH
QUICK
Europe
QUICK
HIGH
SOFT START
SPEED
Plug shape
LOW
SLOW
POWER
ON
POWER
OFF
ON
LOW HIGH QUICK SLOW
SPEED SOFT START
+
- 1 + OFF
2 -
External Dimensions
SEC:40V 1.4A
50/60Hz
PRI:100-240V�`
MODEL:DLC70S-WGB
PRODUCT:CONTROLLER
�EAlways use this tool indoors.
�EAlways use this hearing protection.
instruction manual.
�ETo reduce the risk of injury,user must read
MODELS:DLV30/45/70� � -IKE
following special ELECTRIC SCREWDRIVERS.
�EUse this CONTROLLER in combination with the
SER.No.
T 5A L
132
MADE IN JAPAN
Tokyo,146-8555,Japan
2-9-4,Nakaikegami,Ohta-ku,
NITTO KOHKI CO.,LTD.
TV06090 >PETP<
1 + OFF
2 -
21
DLV3100/3300 series For Miniature Screws & Machine Screws(1.0 - 6.0 mm)
Features
A Labor-Saving "delvo" for Automatic Assembly Robot
• Vibration-proof and shock-proof for long continuous screw tightening
• Torque-up signal output
• High repetitive torque accuracy
series
• DLV3128-EJN • DLV3138-EJN DLV3100 series DLV3300 series
• DLV3148-EJN • DLV3158-EJN
NOTE:The bit mounting is made in a specific way.
Torque (Nm) 0.05 - 0.5 0.3 - 1.2 0.25 - 0.7 0.5 - 1.5 1.2 - 3.0 2.0 - 4.5
Free Speed (min-1) 900 600 900 600 450
Power Consumption (W) Approx. 35 Approx. 45
DLV3100/3300
Screw Size Machine Screw 1.0 - 3.0 2.0 - 3.5 2.3 - 2.6 2.6 - 3.5 3.5 - 5.0 4.5 - 6.0
(mm) Tapping Screw 1.2 - 2.6 2.0 - 3.0 2.3 - 3.0 2.5 - 3.5 3.0 - 4.0 4.0 - 5.0
3.5
2
Model DLC3310
Controller
Screwdriver
External Dimensions
M26 × 1.5
DLV3321/3331 Left-hand thread
222
-0.01
ø28-0.05
ø35
ø30
ø35
10.5 26
83
RM12BPE-5PH(71)
(Hirose Electric
92 Co., Ltd.) RM12BPE-5S(71)
(Hirose Electric Co., Ltd.)
42
74
DLV3121/3131/3141/3151
107.5 9
20.7 38.3 SRCN2A13-3P
40.5 8 Brush Cap (Japan Aviation
54
Electronics
Industry. Ltd.)
ø39-0.05
ø32
ø5 2
ø39
ø34
0
Bit Holder
ø50
173
M41 × 1 277
Left-hand
thread Cord 2 m Unit: mm
22
DLV30/45/70 automation series For Machine Screws (2.6 - 8.0 mm)
Features
For automatic assembly robot
• Three series of screwdrivers can be mounted on the XY robot
• Automatic screw tightening achieves a labor-saving or unattended process
• Long-life brushless motors are incorporated in the electric screwdrivers
series
DLV30LAF-DJN DLV45LAF-DKN
A Vacuum Pickup is optional.
14 *1
Bit Type (mm)
23 9 6.35
ø7
24 5
ø6
*1 : DLV30 series is available upon request for use with 6.35 mm hex. shank bits.
Optional Accessories Torque Diagram (for reference)
8
3 7
High Torque Spring DLV70
6
Bit Torque (Nm)
5
2
DLV30 4 DLV45
3
1
2
Vacuum Pickup Part No. Vacuum Pump Low Torque Spring
DLP7400(M3/M4 screws) TD07285 Model DLP2530/2570 (Standard Accessory) 1
DLP7400 for high torque(M5/M6 screws) TD07286
1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7
Torque Scale Torque Scale
Screwdriver Cable Breakdown List
Power/Input Signal Cable Output Signal Cable
Color Details Color Details
Green Power input White Torque-up signal output
Yellow Power input Black Ground
Blue Bit earth
White Input signal common (Vcc)
Black Start signal input
Orange Forward signal input
Gray Reverse signal input
Power input voltage: 100 V AC
23
For Machine Screws (2.6 - 8.0 mm)
Power Input / Output Signal Schematic Diagram
series
5 - 24 V DC
Power Input
(100 V AC)
Bit Earth Vcc Reverse Forward Start Torque-Up Ground
(Green) (Yellow) (Blue) (White) (Gray) (Orange) (Black) (White) (Black)
5.1kΩ
DLV30/45/70 automation
Screwdriver Inside Screwdriver Inside
Caution
• Each input/output signal is insulated from a screwdriver’s internal circuit.
• Input signal rated range: Use in the range of voltage between 5 – 24 V DC (current 0.5 – 5 mA DC)
• Torque-up signal output maximum rating: Use in the range of voltage under 30 V DC and current 20 mA DC.
External Dimensions
DLV30LAN/SAN/HAN-DJN DLV45LAN/SAN-DKN DLV70LAN-DKN
51
51
3
7
3
7
1
5
9
1
5
Ø39.5
Ø39.5
50
50
274 274
Ø5
Ø4 Ø4
62
62
.5
.5
5.5 5.5
51
51
52
3
7
52
3
7
1
5
9
1
5
Ø39.5
Ø39.5
50
50
274 274
46.5 12 46.5 12
7 7
M41 × 1.0
M41 × 1.0
42 42
5.5 5.5
Thread part Thread part
Ø45
Ø45
51
51
3
7
3
7
1
5
1
5
9
Ø39.5
Ø39.5
50
50
274 274
Sleeve
32.3
Ø17
Ø14.5
Ø15
24
DLR5040A-WE Screw Fastening Counter
Features
For prevention of human fastening errors and enhanced fastening management accuracy
• Ideally suited for the assembly lines of vehicles and electrical equipment requiring reliable screw fastening
DLR5040A-WE/DLR5340-WE
• The controller receives signals from electric screwdrivers to provide highly reliable screw fastening control
• Count Return Function: When a screw is loosened, a reverse signal output from the electric screwdriver
reverses the count by one
• The Count Correction Function does not count elevated screws or double fastening
• Input voltage range from 100 to 240 V AC is acceptable in any part of the world
(The screwdrivers to be used in combination with the counter require input power supplies that
are written on the respective nameplate)
• Link Connection Function: You can build up a simple sequential screw tightening system by
connecting the DLR5040A-WE screw tightening counters in series without using any external
controller such as a programmable controller
• Driver Lock Function prevents unexpected start of screwdrivers Example of use together
with a sensor available in
• Compact and Lightweight (Compared with our conventional models decreased by 30 % in
the market
volume and by 38 % in mass)
• SPC type screwdrivers for DLR5040A-WE are designed on the basis of established
transformerless screwdrivers
Specifications Front and Rear Panels
Model DLR5040A-WE
Predicted fastening OK/NG judge LED indicator Power switch
Count 1 - 99 time LED Fuse(3 A)
Fastening count/ Connecting port for
Counting Method Count-up / Count-down Work set LED indicator setting display electric screwdriver AC inlet
Count Correction Function Count normal fastening only
Self Adjustable Timer Setting 0.01 to 0.99 sec. OK/NG COUNT
Work Detection Function Yes (1 terminal) / No
R
SCREW COUNTER
Features
Up to three sets screwdrivers can be connected to one counter
• Up to eight kinds of screw fastening conditions can be stored in internal memory
for a wide variety of assembly work
• Count-up signal outputs
• Space saving
• The Count Correction Function does not count elevated screws or double
fastening as fastening errors
• Count Return Function: When a screw is loosened, a reverse signal output from
the electric screwdriver reverses the count by one
ch
Front
SCREW COUNTER
�
WORK TIMER
60
F
Work Detection Function Yes (1 terminal) / No
C/M
�
DRIVER
�
Work Installation Timer Setting 0 to 9.5 sec.
V0L A B C
Screw Counter
1 2 3 4 5 6
External Outputs on Terminal Block Setup DIP switch External connection terminal block
OK / NG / COUNT-UP / DRIVER A/B/C
Jumpers for external power supply
Input Voltage 100 - 240 V AC, 50/60 Hz
External Dimensions (mm) 120 12.6
W150 × D120 × H60
Mass (kg) 0.62
Accessory : 2 m cord with UL three-prong plug. This product is for use outside Japan. Side
Unit: mm
25
Dedicated Screwdrivers for DLR5040A-WE and DLR5340-WE
(DLW2300:DLV7100/7200/
Free Speed (min-1) 900 650 1,200 900 650 1,200 8100/8200/30/45/70-SPC)
Power Consumption (W) Approx. 25 Approx. 30 Approx. 25 Approx. 30 • Suitable for horizontal operation
Screw Size Machine Screw 1.0 - 3.0 2.0 - 3.5 2.0 - 3.0 1.0 - 3.0 2.0 - 3.5 2.0 - 3.0
(mm) Tapping Screw 1.2 - 2.6 2.0 - 3.0 2.0 - 3.0 1.2 - 2.6 2.0 - 3.0 2.0 - 3.0
3.5 TD04061 SPC cord for
commercial power source
2
Bit Type (mm) (optional)
11
ø4
Dedicated
Screwdrivers Machine Screw(2.6 - 8.0 mm) Built-in brushless motor
DLV7120 DLV7130 DLV7140 DLV7251 DLV7241 DLV7231 DLV30LL DLV30SL DLV30HL DLV45LL DLV45SL DLV70LL
Lever Start --------
-SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC
Model
Push to Start DLV8120 DLV8130 DLV8140 DLV8150 DLV8251 DLV8241 DLV8231 DLV30LP DLV30SP DLV30HP DLV45LP DLV45SP DLV70LP
-SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC -SPC
Input Voltage 100 V AC, 50/60 Hz *
Torque Adjustment Stepless
Torque (Nm) 0.25 - 0.75 0.5 - 1.7 1.2 - 3.0 2.0 - 4.5 2.0 - 4.5 1.2 - 3.0 0.5 - 1.7 0.4 - 1.6/1.2 - 3.0 2.0 - 4.5 3.8 - 7.0
Electric Screwdriver
Free Speed (min-1) 1,000 700 450 700 1,200 2,000 650 1,200 2,000 650 1,200 650
Power Consumption (W) 35 45
Screw Size Machine Screw 2.6 - 3.0 2.6 - 4.0 3.5 - 5.0 4.5 - 6.0 4.5 - 6.0 3.5 - 5.0 2.6 - 4.0 2.6 - 5.0 4.5 - 6.0 5.0 - 8.0
(mm) Tapping Screw 2.3 - 3.0 2.5 - 3.5 3.0 - 4.0 4.0 - 5.0 4.0 - 5.0 3.0 - 4.0 2.5 - 3.5 2.5 - 4.0 4.0 - 5.0 4.5 - 6.0
14 14
24 5 24 5
ø6
ø6
23 9 6.35 23 9 6.35
ø7
ø7
Mass (g) 710(7100series)/670(8100series) 810 710(7200series)/670(8200series) 700 870 with pistol grip
Cord Length (m) 3 (with connector)
Bit Grounding Equipped as standard
*Please contact us for other voltage availabilities.
26
DLR5640-WN Screw Fastening Counter
Features
The self-adjustable timer function automatically assesses the time required to
complete fastening each screw and reflects it on the judging time setting
• Ideally suited for the assembly lines of vehicles and electrical equipment requiring reliable
screw fastening
• The controller receives signals from electric screwdrivers to provide highly reliable screw
fastening control
• Functions of the controller and counter are integrated into a single unit
• Count Return Function: When a screw is loosened, a reverse signal output from the electric
screwdriver reverses the count by one
• The self-adjustable timer function automatically assesses the time required to complete
tightening each screw and reflects it on the judging time setting
• The Count Correction Function does not count elevated screws or double fastening as
fastening errors
• External Count Function: To be available to various assembling jobs, the DLR5640 enables
counting of two kinds of parts (up to 9 counts each) in addition to the screw tightening counting.
These kinds of counting can be used together.
• Link Connection Function: You can build up a simple sequential screw tightening system by
connecting the DLR5640 screw tightening counters in series without using any external
controller such as a programmable controller
DLR5640-WN
Specifications
Model DLR5640-WN
Count 1 - 99
Counting Method Count-up / Count-down
Count Correction Function Count normal fastening only
Self Adjustable Timer Setting 0.01 to 0.99 sec.
Work Detection Function Yes (1 terminal) / No
External Count Input 2 terminals (PARTS A / PARTS B)
Work Installation Timer Setting 0 to 9.5 sec.
OK Output Timer Setting 0 to 9.5 sec.
NG Alarm ON(1) / ON(2) / OFF
OK Buzzer ON(1) / ON(2) / ON(3) / OFF
Count Return Function ON / OFF
Screw Counter
OK / NG judge
2 m Power cord with U.S.A plug LED indicator
Accessories Suspension bail (2 pcs.)
Work set
LED indicator Fastening count/
setting display
LINK Function (Commom to DLR5040A & DLR5640) Predicted
fastening time
When counters are connected and activated in the screw fastening LED
sequence as shown below, all screwdrivers are on standby except the first
one in the sequence. Only when the first screw fastening is finished, can the
Clear / memory key Function key
next screwdriver change from standby to ready. When the last fastening in
Down key Up key
the sequence is finished, the first screwdriver is once again ready and the
sequence can be repeated again.
N.B. Up to 10 screwdriver/counter sets can be connected to the LINK. External Jumpers for
connection external power Setup DIP switch
terminal block supply
The first The second The third
unit unit unit
AC inlet
Connecting port for
electric screwdriver Power switch
LINK-OUT LINK-IN LINK-OUT LINK-IN
27
Screwdrivers designed for Screw Fastening Counter
DLR5640-WN
DLR5640-WN
Specifications
Model DLV7410A-SPC DLV7410HA-SPC DLV7420A-SPC DLV7321-SPC DLV7331-SPC
Starting Method Lever Start
Torque Adjustment Stepless
Torque (Nm) 0.02 - 0.2 0.15 - 0.4 0.1 - 0.5 0.3 - 1.2
Free Speed (min-1) 500 - 750 700 - 1,000 450 - 600 300 - 1,000 200 - 700
Power Consumption (W) Approx. 10 Approx. 35
Screw Size Machine Screw 1.0 - 2.3 1.6 - 2.6 1.0 - 3.0 2.0 - 3.5
(mm) Tapping Screw 1.0 - 2.0 1.4 - 2.3 1.2 - 2.6 2.0 - 3.0
3.5
Bit Type 2
(mm)
11
ø4
Optional Accesories
28
DLT1173A/1673A/1973A series Torque Checker
Features
Maintaining high assembly quality with ease
• Measured data is stored even after the power is turned off,
DLT1173A/1673A/1973A series
TORQUE CHECKER
Click series
Uploading Program
DLT1973A
Specifications
Model DLT1173A DLT1673A DLT1973A
Measurement Range (N m ) 0.015 - 1.500 0.15 - 10.00 4.00 - 12.00
Within ± 0.5% (Full Scale) Within ± 0.5% (Full Scale)
Calibration Precision Within ± 0.5% (Full Scale)
For 0.2 Nm or less ± 1 digit For 2 Nm or less ± 1 digit
Display 4-digit digital display (Single-line) Data sampling : 1,000 times/sec. Display rate : 12 times/sec.
Measuring Unit kgf • cm, Nm, lbf • in (selectable)
Data Memory 800 pieces of data
Measuring Direction CW and CCW
Measuring Mode 3 modes : PD-TR-PP
Auto Power Off Power off if left untouched for 10 minutes
Torque Checker
Standard Accessories
DLT1173A DLT1673A DLT1973A
Joint/Bit Screw Joint Bit Joint Spring for Joint Soft Joint
Model DLW4430 DLW4360 DLW4660 DLW4000
Measuring (N m ) 0.15 - 1.5 0.15 - 6.5 0.15 - 1.5 4.0 - 12.0
29
Torque Checker
Optional Accessories
ModeI Model Part No. Shape Torque Range DLT1173A DLT1673A DLT1973A
DLW4330 TD03305 OD 4 mm type 0.015 to 0.25 N m
DLW4340 TD03306 OD 4 mm type 0.15 to 1.5 N m
Bit Joint
DLW4350 TD03307 Hex 5 and Hex 6.35 types 0.15 to 1.5 N m
DLW4360 TD03308 Hex 5 and Hex 6.35 types 0.15 to 6.5 N m
DLW4430 TD03309 screw type(Bit size No.1) 0.15 to 1.5 N m
Screw Joint
series
DLW4530*1 TD03310 screw type(Bit size No.2) 0.15 to 5 N m
Soft Joint DLW4000 TD04123 Hex 13 type
4.0 to 12.0 N m
Hard Joint DLW4040 TD04124 (Hex. head bolt)
Spring DLW4660 TV03826 Spring for DLW4340, 4350, 4430
: Standard accessories : Available as option : Unsupported
*1 DLW4530 must be used at 5 N m or less.
Hex 5 mm Hex 5 mm
TORQUE CHECKER
4 mm dia. Hex 6.35 mm Hex 6.35 mm
4 mm dia.
External Dimensions
• DLT1173A • DLT1673A
47 47
42 42
38.5 160 38.5 160
(7.5) 31.5 (7.5) 31.5
CAUTION CAUTION
• Don't use as impact load. • Don't use as impact load.
• Don't apply a torque exceeding the • Don't apply a torque exceeding the
permissible load(120% of max.torque). permissible load(120% of max.torque).
• Read all instructions. • Read all instructions.
DATA OUTPUT
CLEAR CLEAR
MEM/ MEM/
OUTPUT AVE MODE OUTPUT AVE MODE
OUTPUT
ANALOG
OUTPUT
ANALOG
• DLT1973A
48
43 200
39.5 160 20
32.5
103.5
112
86
GOOD NG UNIT
POWER PRG/
ON/OFF UP DOWN SET
RESET
DC IN
CLEAR
MEM/
OUTPUT AVE MODE
OUTPUT
ANALOG
6.5
unit: mm
30
Accessories
Tool Balancer Shaker Box Made of Anti-electrostatic Resin
DLW3602
DLW3402
DLW3802
TW-06R/1R RW-3/5
The screws will fall into the heads-up position for easier vacuum or
magnetic pickup.
The anti-electrostatic resin greatly reduces static buid-up and dust
attached to the shaker box.
Model DLW3402 DLW3602 DLW3802
Easy to adjust tension by using handle. Part No. TD04110 TD04111 TD04112
Model TW-06R TW-1R RW-3 RW-5 Hole Pitch (mm) 6 6 8
Capacity (kg) 0.2 - 0.6 0.5 - 1.5 1.0 - 3.0 2.5 - 5.0 Hole Depth (mm) 13.5 13.5 12.5
Stroke (m) 1.5 1.5 2 No. of Holes 273 273 160
Mass (kg) 0.3 0.3 0.7 0.9 Screw Size (mm) 1.7 - 2 2 - 2.6 3-4
DLW5201
Easy-to-attach grip suitable for horizontal operation. Provides a flange which enables the operator to apply axial
pressure through the heel of the hand.
31
Accessories
Torque Reaction Arm
Usage Example
Optional Cord
0.4 or 1.0 m
Curl Cord
Please inquire of the distributor for the price and minimum quantity on each optional cord.
Part No. Optional Cord Applied Models Length(m)
TD02826 5P to 6P Exchange Cord*1 0.1
TD02548 Extension Cord For 5P DLV7300 3.0
TD03159 Extension Cord For 6P 2.0
TD01882 Curl Cord 0.4
TD02820 Curl Cord DLV7500/8500 1.0
TD02438 Cord Connector DLW9100
Cord Connector
*1 : "5P to 6P Exchange Cord" is used to connect "5-prong Screwdriver"
to "6-prong Controller".
32
Sleeves and Vacuum Pickups
For DLV7400A/5700/5800/7300/7000/8000 series
Vacuum Pickup
DLP6500 (for DLV7000 and 8000 Series Electric Screwdrivers) DLP5300 (for DLV7400A / 5700 / 5800 Electric Screwdrivers)
DLP7100 (for DLV7313 Electric Screwdriver)
DLP7200 (designed for OD 4 mm Shank Bit for
DLV7323 / 7333 Electric Screwdrivers)
DLP7300 (designed for 6.35 mm Hex. Shank Bit for
DLV7323 / 7333 Electric Screwdrivers)
Sleeve
Sleeve
Standard Set
Vacuum Pickup DLP5300 DLP6500 DLP7100 DLP7200 DLP7300
(Part No.) (TD04342) (TD00343) (TD00345) (TD00346) (TD00347)
DLS2120 × 1 pc. DLS2124 × 1 pc. DLS2122 × 1 pc. DLS2123 × 1 pc. DLS2135 × 1 pc.
Accessories DLS2124 × 1 pc. DLS2127 × 1 pc. DLS2124 × 1 pc. DLS2124 × 1 pc.
DLS2130 × 1 pc. DLS2127 × 1 pc. DLS2127 × 1 pc.
Unit: mm
33
Sleeves and Vacuum Pickups
For DLV7100/7200/8100/8200- J series
Vacuum Pickup
DLP7000 (for DLV7100 / 7200 / 8100 / 8200- J Series Electric Screwdrivers)
Sleeve
Standard Set
Vacuum Pickup DLP7000
(Part No.) (TD00344)
DLS3223 × 1 pc.
Accessories
DLS3225 × 1 pc.
Unit: mm
Sleeve DLS3000 series (Metal) Sleeve Bit
Model Part No. ød øD L
DLS3222 TD00364 5.6 7 5 No.1 × 5 × 70
DLS3223 TD05024 6.1 9
34
ød
Phillips Head
DLS3225 TD00366
(No. × d × L)
7.1 9
L DLS3226 TD00367 4.6 7
DLS3227 TD00368 No.1 × 4 × 100
5.1 7 18
DLS3228 TD00369 5.6 7 No.1 × 5 × 100
65
DLS3229 TD00370 6.1 9 No.2 × 5 × 100
DLS3230 TD00371 6.4 9
No.2 × 6 × 100
DLS3231 TD00372 7.1 9
Vacuum Pickup
DLP7400
ØD
Sleeve
Ød
Phillips Head
ød øD L S Bit
L Model Part No. (No. × d × L)
mm mm mm mm
S No.1 × 7 × 75
DLS4220 TD08001 9.1 11 5 6
45 mm NK 35 No.2 × 7 × 75
DLS4221 TD08002 10.6 12.5 5.5 7 No.3 × 7 × 75
34
NK BIT
For DLV7400A/5700/5800/7300/ For DLV7100/7200/8100/8200/3100/
7000/8000/3300 series 30 series
3.5 24 5
ø4
2
11 14
OD 4 mm Shank Unit: mm
OD 5 mm Hex. Shank Unit: mm
Size Size
Model Part No. Dimensions Model Part No. Dimensions
No. × d × L No. × d × L
TD20009 44 TD20193 70
4
ø6
00 2
64 TD20194 100
d
TD20010 3.5 No.
ø4
TD20021 44 d TD20196 70 14
1.8 No. 1 5 30
TD20022 64 TD20197 100 24 5
Phillips
0 L
TD20029 44 20 11 TD20200 70
2.5
64 L NK31 TD20201
6
100
TD20030
Phillips
NK4D
d
TD20037 44 TD20210 70 No.
3 5
TD20038 64 TD20211 100 14
1 3.5 2 24 5
d
TD20039 44 TD20214 70 L
4 6
TD20040 64 No. TD20215 100
TD20047 44 11
2 4 L Model Part No. No. × L Dimensions
TD20048 64
TD20050 3 6 44 TD20224 70
1 X X-X'
Phillips TD20225 100 No.
Model Part No. W × T × L Dimensions NK16 TD20232 70
X' 14
TD20051 2 0.3 TD20233 2 100 L 5
3.5
ø4
TD20053 3 0.4 44
NK4DM
T
4 0.5
Model Part No. H × d × L Dimensions
TD20054 20 11
TD20055 5 0.65 L TD20254 2 4 70
ø6
d
Part No. H × L H 14
30
Model Part No. H × L Dimensions TD20256 2.5 L 24 5
Hexagon Head
ø6
70
TD20057 2 NK31X TD20260 4
Hexagon Head
3.5 H
ø4
ø6
d
TD20064 4 6 TD20274 6 10 4.5 70
D
TD20065 4.5 7 TD20276 70 H 14
44 7 11 5.5 25 5
24
Hex Socket
ø4
ø6
d
H 11 TD20282 70
D
L 10 16 8 14
TD20283 100 H 25
24
L 5
35
NK BIT
For DLV7500/8500/7100/7200/8100/
8200/02/12/16/30/45/70 series
9 6.35
Size
Model Part No. Dimensions
No. × d × L
TD20306 75
4
TD20307 100
d
No.
TD20308 50
TD20309 75 30
1 L
TD20310 100
TD20311 120
TD20312 150
TD20313 200
TD20319 50
Phillips
TD20320 75
NK35 TD20321 100
2 7
TD20322 120
d
No.
NK15 TD20363 75 12
TD20364 2 100 L
TD20366 150
TD20367 200
TD20371 75
TD20372 100
3
TD20374 150
TD20375 200
TD20379 7 0.9 75
T
TD20385 1.5 3 70
H
TD20388 2 15
Hexagon Head
L
Part No. H × L
NK35X TD20391 2.5
TD20394 3 70
TD20397 4 H
L
TD20400 5
50
TD20404 6
TD20443 100
TD20457 75
D
NK35BN TD20458
13 19 10
100 H 9
25 23 6.35
L
36
SAFETY GUIDE
Be sure to read and understand the following safety notations and all safety precautions.
WARNING
• Keep work area clean. Cluttered work areas and benches invite • Remove adjusting keys and wrenches. Form habit of checking to see
accidents and injuries. that keys and adjusting wrenches are removed from tools before
• Consider proper working environments for each tool carefully. Do not turning it on.
expose electric tools to extreme amounts of moisture or direct contact • Always avoid an unexpected start by having all power switches in the
with water or rain. Keep area well lit at all times to prevent hidden off position prior to attaching to a power supply. Never carry tools with
dangers and never operate the equipment near flammable liquids or in your finger on the on/off switch when the power is attached. Never plug
gaseous or explosive atmospheres. the cord into a receptacle while your finger is on the on/off switch.
• Prevent operators from electric shock. When using electric tools, • When the tool is used outdoors, use an electric extension cord or cable
prevent body contact with grounded surfaces (e.g. pipes and outer suitable for outdoor use.
frames of radiators, microwave ovens, and refrigerators, etc.). • Stay alert. Watch what you are doing. When using electric tools, take
• Keep all electric tools and power cords away from children and all good care of tool handling, working manner, and surrounding
unauthorized personnel. Also all visitors should be kept away from work conditions. Use common sense. Do not operate tool when you are tired.
area. • Check damaged parts. Before further use of the tool, an accessory or
• Properly store tools and accessories while not in use. They should be other part that is damaged should be carefully checked to determine
kept in a dry, locked-up location out of reach of children or that it will operate properly and perform its intended functions. Check
unauthorized personnel. for alignment of moving parts, binding of moving parts, breakage of
• Do not force tool. It will do the job better and more safely at the rate for parts, mounting, and any other conditions that may affect its operation.
which it was intended. When repairing or replacing parts, follow the directions of the
• Use the right electric power tool that can complete the job within its instruction manual. The part that is damaged should be properly
specifications. Do not attempt to adapt improper attachments or repaired or replaced by an authorized service facility unless otherwise
accessories to complete a job. Do not use the tool for other than what indicated elsewhere in this operation manual. Have defective switches
they were designed for. replaced by an authorized service facility. Do not use the tool if the
• Dress properly. Do not wear loose clothing and/or accessories. (gloves, switch cannot be turned on and off.
necklace etc.) They can be caught in moving parts. Non-skid footwear is • Use only recommended accessories and attachments as per tool
recommended in outdoor operation. Wear protecting hair covering to operator manual and “delvo” general catalog. Use of improper
contain long hair. accessories and attachments may result in an accident or serious injury.
• Always wear safety glasses during operation. Wear respiratory • Any repairs on the tool should be performed only by an authorized
protection when working in an environment where dust particles are service facility. Do not modify the tool that is complying with the safety
generated during operation. standard. If the repairman who has poor knowledge and skill repairs the
• Do not abuse cord. Never carry tool by cord or yank it to disconnect tool, the tool may not give a good performance and result in an
from receptacle. Keep cord from heat, oil, and sharp edges. increased risk of injury to the user.
• Use clamps or a vise to secure the work piece tightly and eliminate • The power source must be limited to the individual tools specifications
vibration. Never hold the work piece with your hands, keep both hands as stated on the nameplate or instruction manual. If used at a higher or
on the electric tool for increased productivity. lower voltage than indicated, it may cause failure and result in an
• Do not overreach. Keep proper footing and balance at all times. increased risk of injury to the user.
• Maintain tools with care. For safe and efficient work, use the proper bit • Before work operation carefully check if there are underground
and check it regularly. Do not use the bit with a worn out or deformed installations such as conduit, water pipe, and gas pipe, etc. If a tool
tip. When oiling and replacing parts, follow the instructions given by the should touch them, it might cause electric shock, electric leak, or gas
instruction manual. Inspect tool cords periodically and if damaged, have leak.
them replaced by an authorized service facility. Keep handles dry,clean, • Hold the tool body firmly so as not to be swung by it when using. If not,
and free from oil and grease. this may cause injury.
• Disconnect a tool or a controller when not in use, when repairing, or • Do not bring hand or face close to moving parts such as bit etc. when
when changing accessories and bits, etc. using. This may cause injury.
• When you have dropped the tool by mistake, carefully check the tool if
there is breakage, cracks or deformation. This may cause injury.
CAUTION
• Install bits or accessories securely in accordance with the operation • If the tool is overheating or functioning abnormally, stop using the
manual. Insufficient installation may cause injury. screwdriver immediately and inspect it to see whether any repairs are
• Whenever setting the torque, unplug the cable of the tools. Adjusting necessary. Otherwise this may cause failure or injury.
the torque setting during rotation may cause injury. • The electric screwdriver may overheat depending on the type of screw,
• When operating a tool at high places, check that there is no person type of screw-tightened material, or frequency of use. To avoid
under the places. Do not stumble over the cord nor drop the material or overheating, stop operating the screwdriver for a time or use several
tool body. This may cause injury. drivers in alteration. Overheating may reduce the life of the product or
• Never leave a tool running unattended on the working bench or floor. cause failure or injury.
Always turn the power switch or lever to the off position and disconnect • The fastening torque may vary depending on how the product is
from the power source when not in use. operated or held, the type of screw, and the fastening conditions. Use a
• Do not overload to the extent that the motor locks or the clutch torque wrench or similar tool to check that the fastening torque is
malfunctions. This may cause smoke, fire, failure or injury. appropriate.
37
38
Electric Screwdrivers
The logo for delvo is registered trademark or a trademark of Nitto Kohki Co., Ltd. in Japan,
the United States and/or certain other countries.
NITTO KOHKI AUSTRALIA PTY LTD NITTO KOHKI CO., LTD. INDIA LIAISON OFFICE
77 BRANDL STREET BRISBANE TECHNOLOGY PARK 3RD FLOOR, BUILDING NO.9-A DLF CYBER CITY, PHASE-III,
EIGHT MILE PLAINS QLD 4113, AUSTRALIA GURGAON, HARYANA 122002, INDIA
Tel : +61-7-3340-4600 Fax : +61-73340-4640 Tel : +91-124-454-5031 Fax : +65-6227-0192
www.nitto-australia.com.au
DISTRIBUTED BY
This catalog is printed using environmentally friendly paper and vegetable oil inks.
Specifications and designs are subject to change at any time without notice. Printed in Japan 15KV06- 1