Академический Документы
Профессиональный Документы
Культура Документы
53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 1
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
Specifier's comments:
1 Anchor Design
1.1 Input data
Anchor plate
CBFEM
: lx x ly x t = 250.0 mm x 250.0 mm x 12.0 mm;
Profile: Advance UKB, 127 x 76 x 13; (L x W x T x FT) = 127.0 mm x 76.0 mm x 4.0 mm x 7.6 mm
Base material: cracked concrete, C25/30, fc,cyl = 25.00 N/mm ; h = 250.0 mm
2
CBFEM
- The anchor calculation is based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
1
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 2
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
1 2
Anchor forces are calculated based on a component-based Finite Element Method (CBFEM)
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
2
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 3
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
NRk,s
NEd ≤ NRd,s = EN 1992-4, Table 7.1
gM,s
NRk,c
NEd ≤ NRd,c = EN 1992-4, Table 7.1
gM,c
0 Ac,N
NRk,c = NRk,c · 0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · ≤ 1.00 EN 1992-4, Eq. (7.4)
ccr,N
1
y ec1,N = ≤ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eN,1
scr,N )
1
y ec2,N = ≤ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eN,2
scr,N )
y M,N =1 EN 1992-4, Eq. (7.7)
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] fc,cyl [N/mm ]
67,275 38,025 97.5 195.0 25.00
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
3
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 4
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
VRk,s
VEd ≤ VRd,s = EN 1992-4, Table 7.2
gM,s
0
VRk,s = k7 · VRk,s EN 1992-4, Eq. (7.35)
0
VRk,s [kN] k7 VRk,s [kN] gM,s VRd,s [kN] VEd [kN]
54.500 1.000 54.500 1.250 43.600 0.197
VRk,cp
VEd ≤ VRd,cp = EN 1992-4, Table 7.2
gM,c,p
VRk,cp = k8 · NRk,c EN 1992-4, Eq. (7.39a)
0 A
NRk,c = NRk,c · c,N
0
· y s,N · y re,N · y ec1,N · y ec2,N · y M,N EN 1992-4, Eq. (7.1)
Ac,N
0 1,5
NRk,c = k1 · √fck · hef EN 1992-4, Eq. (7.2)
0
Ac,N = scr,N · scr,N EN 1992-4, Eq. (7.3)
c
y s,N = 0.7 + 0.3 · ≤ 1.00 EN 1992-4, Eq. (7.4)
ccr,N
1
y ec1,N = ≤ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,1
scr,N )
1
y ec2,N = ≤ 1.00 EN 1992-4, Eq. (7.6)
1+ ( 2 · eV,2
scr,N )
y M,N =1 EN 1992-4, Eq. (7.7)
2 0 2 2
Ac,N [mm ] Ac,N [mm ] ccr,N [mm] scr,N [mm] k8 fc,cyl [N/mm ]
119,025 38,025 97.5 195.0 3.410 25.00
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
4
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 5
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
a a
bN + bV ≤ 1.0
Concrete failure
1.6 Warnings
• The anchor design methods in PROFIS Engineering require rigid anchor plates as per current regulations (ETAG 001/Annex C, EOTA
TR029, etc.). This means load re-distribution on the anchors due to elastic deformations of the anchor plate are not considered - the anchor
plate is assumed to be sufficiently stiff, in order not to be deformed when subjected to the design loading. PROFIS Engineering calculates
the minimum required anchor plate thickness with CBFEM to limit the stress of the anchor plate based on the assumptions explained above.
The proof if the rigid base plate assumption is valid is not carried out by PROFIS Engineering. Input data and results must be checked for
agreement with the existing conditions and for plausibility!
• Checking the transfer of loads into the base material is required in accordance with EN 1992-4, Annex A!
• Attention! In case of compressive anchor forces a buckling check as well as the proof of the local load transfer into and within the base
material (incl. punching) has to be done separately.
• The design is only valid if the clearance hole in the fixture is not larger than the value given in Table 6.1 of EN 1992-4! For larger diameters
of the clearance hole see section 6.2.2 of EN 1992-4!
• The accessory list in this report is for the information of the user only. In any case, the instructions for use provided with the product have to
be followed to ensure a proper installation.
• For the determination of the y re,v (concrete edge failure) a concrete cover of the edge reinforcement c = 30 mm is assumed
• The anchor design methods in PROFIS Engineering require rigid anchor plates, as per current regulations (AS 5216:2018, ETAG 001/Annex
C, EOTA TR029 etc.). This means that the anchor plate should be sufficiently rigid to prevent load re-distribution to the anchors due to
elastic/plastic displacements. The user accepts that the anchor plate is considered close to rigid by engineering judgment."
• The characteristic bond resistances depend on the return period (service life in years): 50
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
5
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 6
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
Hilti HST3 stud anchor with 78 mm embedment, M16 hef1, Steel galvanized, installation per ETA-98/0001
y
125.0 125.0
50.0
3 4
125.0
150.0
x
125.0
1 2
50.0
Coordinates Anchor mm
Anchor x y c-x c+x c-y c+y
1 -75.0 -75.0 - - - -
2 75.0 -75.0 - - - -
3 -75.0 75.0 - - - -
4 75.0 75.0 - - - -
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
6
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 7
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
7
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 8
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
N
Stand-off installation: eb = 0.0 mm (No stand-off); t = 12.0 mm
Profile: 127 x 76 x 13; (L x W x T x FT) = 127.0 mm x 76.0 mm x 4.0 mm x 7.6 mm
IO
Material: S 235;fy = 235.00 N/mm²; εlim = 5.00%
Eccentricity x: 0.0 mm
Eccentricity y: 0.0 mm
Base material: Cracked concrete; C25/30; fc,cyl = 25.00 N/mm²; h = 250.0 mm; E = 31,000.00 N/mm²; G = 12,916.67
RS
N/mm²; v = 0.20
Welds (profile to anchor plate): Type of redistribution: Plastic
Material: S 235
Mesh size: Number of elements on edge: 8
Min. size of element: 10.0 mm
VE
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
8
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 9
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
2.2 Summary
Description Profile Anchor plate Concrete [%]
sEd [N/mm²] ePl [%] sEd [N/mm²] ePl [%] Hole bearing [%]
1 Combination 1 503.90 127.92 237.87 1.37 1 105
2.3 Anchor plate classification
Results below are displayed for the decisive load combinations: Combination 1
Anchor tension forces Equivalent rigid anchor plate (CBFEM) Component-based Finite Element Method
(CBFEM) anchor plate design
Anchor 1 9.995 kN -0.005 kN
Anchor 2 9.995 kN -0.005 kN
Anchor 3 26.777 kN 41.188 kN
N
Anchor 4 26.777 kN 41.214 kN
User accepted to consider the selected anchor plate as rigid by his/her engineering judgement. This means the anchor design guidelines can
IO
be applied. RS
VE
L
IA
TR
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
9
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 10
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
2.4 Profile/Stiffeners/Plate
Profile and stiffeners are verified at the level of the steel to concrete connection. The connection design does not replace the steel design for
critical cross sections, which should be performed outside of PROFIS Engineering.
Results
Part Load Material sEd [N/mm²] ePl [%] fy [N/mm²] gM0 fy/gM0 elim [%] Status
combination [N/mm²]
Plate Combination S 235 237.87 1.37 235.00 1.00 235.00 5.00 OK
1
N
Profile Combination S 235 503.90 127.92 235.00 1.00 235.00 5.00 NOT OK
1
Profile Combination S 235 503.90 127.92 235.00 1.00 235.00 5.00 NOT OK
IO
1
Profile Combination S 235 259.34 11.58 235.00 1.00 235.00 5.00 NOT OK
1
RS
2.4.1.1 Equivalent stress
Results below are displayed for the decisive load combination: 1 - Combination 1
VE
235.00 N/mm²
L
IA
TR
0.00 N/mm²
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
10
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 11
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
5.00%
N
IO
RS
VE
0.00%
2.4.2 Hole bearing
Decisive load combination: 1 - Combination 1
L
Equations
k1 ab fu d t
Fb,Rd =
gM2
TR
VEd
Utilization =
Fb,Rd
Variables
k1 ab fu [N/mm²] d [mm] t [mm] gM2
Anchor 1 2.50 0.93 360.00 16.0 12.0 1.25
Anchor 2 2.50 0.93 360.00 16.0 12.0 1.25
Anchor 3 2.50 1.00 360.00 16.0 12.0 1.25
Anchor 4 2.50 1.00 360.00 16.0 12.0 1.25
Results
VEd [kN] Fb,Rd [kN] Utilization [%] Status
Anchor 1 0.129 128.013 1 OK
Anchor 2 0.129 128.028 1 OK
Anchor 3 0.196 138.240 1 OK
Anchor 4 0.197 138.240 1 OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
11
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 12
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
2.5 Concrete
Decisive load combination: 1 - Combination 1
According to EN1992-1-1 section 6.7(4), the concrete should have sufficient reinforcement to take into account the tensile forces that develop
due to the fixture attachment. The definition of the reinforcement in the concrete is out of scope of PROFIS Engineering.
N
IO
RS
VE
L
0.00 N/mm²
IA
2.5.2 Verification of compression in concrete under the anchor plate around the profile as per EN1992-1 section 6.7 and EN1993-1-8,
section 6.2.5
Equations
TR
fjd
bj kj acc fck
=
gc
N
s = A
eff
Utilization =
s
fjd
Variables
N [kN] Aeff [mm²] bj kj acc fck [N/mm²] gc
85.349 2,427 0.67 3.00 1.00 25.00 1.50
Results
s [N/mm²] fjd [N/mm²] Utilization [%] Status
35.17 33.50 105 NOT OK
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
12
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 13
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
N
fy Yield strength
gc Service factor - SP 16, Table 41
IO
gM0 Steel safety factor gamma M0
gM2 Steel safety factor gamma M2
k1 Factor for edge distance and bolt spacing perpendicular to the direction of load transfer - EN 1993-1-8 - Table 3.4
RS
kj Concentration factor
N Resulting compression force
s Average stress in concrete
sEd Equivalent stress
t Thickness of the anchor plate
VE
2.7 Warnings
● By using the CBFEM calculation functionality of PROFIS Engineering you may act outside the applicable design codes and your specified
anchor plate may not behave rigid. Please, validate the results with a professional designer and/or structural engineer to ensure suitability
L
Please note that no simple replacement of the anchor is possible as the anchor stiffness has a major impact on the load distribution
results.
TR
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
13
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 14
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
3 Summary of results
Design of the anchor plate, anchor, welds and other elements are based on CBFEM (component based finite element method) and Eurocode
regulations.
Load combination Max. utilization Status
Anchors Combination 1 347% NOT OK
Anchor plate Combination 1 100% OK
Concrete Combination 1 105% NOT OK
Profile Combination 1 215% NOT OK
N
IO
RS
VE
L
IA
TR
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
14
Hilti PROFIS Engineering 3.0.53
www.hilti.group/content/hilti/CP/XX/en/non-transactional/light-pages/middle-east.html
Company: Page: 15
Address: Specifier:
Phone I Fax: | E-Mail:
Design: Concrete - Jan 5, 2020 Date: 1/5/2020
Fastening point:
N
Software in each case by carrying out manual updates via the Hilti Website. Hilti will not be liable for consequences, such as the recovery
of lost or damaged data or programs, arising from a culpable breach of duty by you.
IO
RS
VE
L
IA
TR
Input data and results must be checked for conformity with the existing conditions and for plausibility!
PROFIS Engineering ( c ) 2003-2019 Hilti AG, FL-9494 Schaan Hilti is a registered Trademark of Hilti AG, Schaan
15