Академический Документы
Профессиональный Документы
Культура Документы
HANGERS
Manufacturers of Vibration Control Products SPRING,
350 Rabro Drive 2101 W. Crescent Ave., Suite D RUBBER and
Hauppauge, NY 11788 Anaheim, CA 92801
631/348-0282 714/535-2727 COMBINATION
FAX 631/348-0279 FAX 714/535-5738
HANGERS
Info@Mason-Ind.com • www.Mason-Ind.com H-610-10.1 BULLETIN
The Series 30 design solved the short circuiting problem, but we were
still dealing with a design having poor high frequency control. The
elastomeric cup is a much improved washer that cannot short circuit,
but still a washer. The idea of placing a steel spring in series with a
DNHS Hanger Series 30N Hanger rubber hanger element started about 1957. Our DNHS Series was the
first improvement on early designs, and the 30N configuration was the
obvious advance on the DNHS as they incorporate the 30 degree swing
capacity. Series 30N are the top-of-the-line and recommended for all
highly critical locations where it is equally important to isolate both noise
and vibration.
UPPER UPPER &
H LDS RUBBER ROD BY LOWER
SPRING CUP OTHERS RODS BY
with a project- OTHERS
LRP ing bushing to 1/4"
prevent steel to (6mm)
steel contact. 1/4"
REX (6mm)
REX
Adjust nut
30° 30° to provide 30°
Adjust nut 1/4"(6mm)
D to provide Seismic Rebound washer
Precompression 1/4” Steel and Bonded clearance
Plate. Hangers (6mm) LDS Rubber after Seismic Rebound
Rod can swing are precom- Steel and Bonded
30° 30° before plate Washer holds hanger is
pressed to rated clearance precompression fully LDS Rubber
contacting load or assigned Washer limits
W resilient after and limits upward loaded.
load as required. hanger seismic motion. upward seismic
bushing. motion.
is fully Hangers are
STEEL DISK BONDED loaded. precompressed
TO LDS RUBBER to rated load or
assigned load as
1/4" Seismic required. Scale
(6mm) 1/2"
(13mm) Rebound indicates deflection.
Washer
Ratings & Dimensions for 1"(25mm) Deflection Spring Hangers (inches mm)
Spring Only Lower Max. Rod Vertical
Rated Rated Spring Rod Rod Exten- ‘G’ Ratings
Capacity Defl.† Constant Spring Free Penetration Dia. sion Com-
Type Size (lbs) (kg) (in) (mm) (lbs/in) (kg/mm) Color OD Height D H W LRP MRD REX Tension pression
X-12 12 5 1.25 32 10 0.18 Orange 10.0; 10.0;
X-23 23 10 1.30
33 18 0.30 Brown 10.0; 10.0;
X-33 33 15 1.10
28 30 0.54 Red 10.0; 10.0;
X-54 54 24 1.20
30 45 0.80 White 10.0; 10.0;
X-76 76 34 1.02
25 73 1.36 Black 11/2 21/2 21/2 41/4 27/8 31/2 3/8 13/4 10.0; 10.0;
X-113 113 51 1.00
25 113
2.04 Yellow 38 64 64 108 73 89 10 44 10.0; 7.6
30- X-130 130
59 1.00
25 130
2.36 Purple 10.0; 6.6
X-175 175 79 1.00
25 175
3.16 Silver 10.0; 4.9
X-210 210 95 1.00
25 210
3.80 Blue 9.0 4.1
A-12 12 5 1.00 25 12
0.20 Red 10.0; 10.0;
0.32 Gray 1 /4 1 /8 2 /4 5 /4 3 /4 3 /2
3 7 3 3 1 1 5/8 21/4
A-18 18 8 1.00 25 18 10.0; 10.0;
PC30- A-25 11 1.00
25 0.44 Orange 44 48 70 146 83 89 16 57
25 25 10.0; 10.0
19 1.18
A-41 41 30 35
0.63 Pink 10.0; 10.0;
25 1.14
A-56 56 30 49
0.83 Black 13/4 21/4 23/4 53/4 31/4 4 5/8 21/4 10.0; 10.0;
33 1.06
A-73 73 27 69
1.22 Tan 44 57 70 146 83 102 16 57 10.0; 10.0;
43 1.01
A-95 95 26 94
1.65 Green 10.0; 10.0;
PC30S- B-138 138 63 1.32 34 105
1.85 White 10.0; 10.0;
B-222 222 101 1.16
29 191
3.48 Blue 10.0; 6.6
B-278 278 126 1.09
28 255
4.50 Purple 23/8 27/8 4 71/4 43/4 41/4 5/8 21/4 10.0; 5.2
B-336 336 152 1.00
25 336
6.08 Silver 60 73 102 184 121 108 16 57 10.0; 4.3
B-410 410 186 1.07
27 385
6.89 Black 10.0; 3.6
B-540 540 245 1.00
25 540
9.80 Yellow 10.0; 2.7
RW30- C-630 630 286 1.13 29 558 9.86 Gray 10.0; 5.4
C-800 800 363 1.00
25 800 14.5 Orange 27/8 35/8 4 83/4 51/4 5 3/4 21/4 7.9 4.0
C-1010 1010 458 1.10
28 920 16.4 Green 73 92 102 222 132 127 19 70 6.3 3.1
C-1265 1265 574 1.00
25 1265
23.0 Red 5.0 2.5
D-1575 1575 714 1.23
31 1280
23.0 Pink 33/4 47/8 43/4 121/2 53/4 7 7/8 21/2 10.0; 6.0
D-2150 2150 975 1.03
26 2095
37.5 Purple 95 124 121 318 146 178 22 69 9.0 4.4
1 1 1 7 1
1252 1.00
F-2760 2760 50.1 Silver 4 /2 5 /8 6 12 6 /4 7 /8 2 /2
25 2760 5.0 4.3
114 130 152 305 159 178 22 64
†
All springs have additional travel to solid equal to 50% of Rated Deflection. ;
10.0 indicates a rating of 10 G’s or greater
4
MASON INDUSTRIES 30N, PC30N, PC30NS & RW30N
1"(25mm) DEFLECTION 30° SWING – X, A, B, C, D & F SPRING and DOUBLE DEFLECTION LDS HANGERS
30N FOR ROD ATTACHMENT UPPER & PC30N
TYPE 30N
PC30NS
TYPE 30N PRECOMPRESSED &
RW30N
TYPE 30N
LOWER PRECOMPRESSED SEISMIC RESTRAINT SEISMIC RESTRAINT
RODS BY
OTHERS Install with hanger box snug to 1/4" (6mm) Seismic LDS Rubber Washer,
UPPER ROD so washer is tight to overhead surface. Upper hanger element deflects
BY OTHERS under load, leaving space on top. Washer cushions upward seismic travel.
Clearance Seismic Rebound
not Critical Steel and Bonded
URP LDS Rubber
Washer
DOUBLE
H DEFLECTION
LDS ELEMENT UPPER ROD UPPER &
with projecting DEFLECTION BY OTHERS LOWER
bushing SCALE RODS BY
DEFLECTION OTHERS
SCALE
LRP LDS SPRING 1/4"
CUP with a (6mm)
projecting REX 1/4"
REX (6mm)
bushing to
prevent steel to 1/4"
steel contact. Adjust nut
30° (6mm) 30° to provide 30°
1/4"(6mm)
Adjust nut Seismic Rebound
to provide washer
D Steel and Bonded LDS clearance
Precompression 1/4” Rubber Washer holds Seismic Rebound
Plate. Hangers (6mm) after hanger Steel and
Rod can swing precompression and is fully
are precom- plate limits upward seismic Bonded LDS
30° before pressed to rated clearance loaded. Rubber Washer
contacting motion. Hangers are
30° load or assigned after precompressed to rated limits upward
resilient load as required. hanger seismic motion.
bushing. load or assigned load as
W is fully required. Scale indicates
loaded. deflection.
STEEL DISK BONDED Upper &
TO LDS RUBBER
Lower
1/4" Seismic
(6mm) 1/2"
(13mm) Rebound
Washer
Ratings & Dimensions for 1"(25mm) Deflection Spring and Double Deflection LDS Hangers (inches mm)
Spring Average REX– Rod Extension V
ertical
Rated Rated Constant†† Defl. Spring Only
LRP– Lower Rod Penetration URP– Upper Rod G Ratings
Capacity Defl. † MRD–
(lbs/in) LDS Spring Free Com-Max. Rod Diameter Penetration
Type Size (lbs) (kg) (in) (mm) (kg/mm) Rubber Color OD Height D H W LRP MRD REX URP Tension pression
X-12 12 5 1.45 37 10 0.18 Orange 10.0; 10.0;
X-23 23 10 1.50 38 18 0.30 Brown 10.0; 10.0;
X-33 33 15 1.30 33 30 0.54 Red 10.0; 10.0;
X-54 54 24 1.40 36 45 0.80 White 10.0; 10.0;
X-76 76 34 1.22 31 73 1.36 0.20 Black 11/2 21/2 21/2 51/2 27/8 31/4 3/8 21/4 13/4 10.0; 10.0;
X-113 113 51 1.20 30 113 2.04 5 Yellow 38 64 64 140 73 83 10 57 44 10.0; 6.7
30N- X-130 130
59 1.20 30 130 2.36 Purple 10.0; 5.8
X-175 175 79 1.20 30 175 3.16 Silver 10.0; 4.3
X-210 210 95 1.20 30 210 3.80 Blue 10.0; 3.6
A-12 12 5 1.35 34 12 0.20 Red 10.0; 10.0;
8 1.35 34 18 0.32 0.35 Gray 1 /4 1 /8 2 /4 6 /4 3 /4 3 /4
3 7 3 3 1 1 5/8 21/4 21/4
A-18 18 10.0; 10.0;
9 Orange 44 48 70 171 82 83 16 57 57
PC30N- A-25 25 11 1.35 34 25 0.44 10.0; 10.0;
3 0 N /c 619 1.53
A-41 41 1 0 * c39 35
h 10 m in
0.63 Pink 10.0; 10.0;
A-56 56 25 1.49 38 49 0.83 0.35 Black 13/4 21/4 23/4 63/4 31/4 35/8 5/8 21/4 21/4 10.0; 10.0;
A-73 73 33 1.41 36 69 1.22 9 Tan 44 57 70 171 82 92 16 57 57 10.0; 10.0;
A-95 95 43 1.36 35 94 1.65 Green 10.0; 10.0;
PC30NS- B-138 138 63 1.67 42 105 1.85 White 10.0; 10.0;
B-222 222 101 1.51 38 191 3.48 Blue 10.0; 7.3
B-278 278 126 1.44 37 255 4.50 0.35 Purple 23/8 27/8 4 63/4 43/4 33/4 5/8 21/4 23/4 10.0; 5.8
B-336 336 152 1.35 34 336 6.08 9 Silver 60 73 102 171 121 95 16 57 70 10.0; 4.8
B-410 410 186 1.42 36 385 6.89 Black 10.0; 4.0
B-540 540 245 1.35 34 540 9.80 Yellow 10.0; 3.0
RW30N- C-630 630 286 1.53 39 558 9.86 Gray 10.0; 3.2
C-800 800 363 1.40 36 800 14.5 0.40 Orange 27/8 35/8 43/4 9 51/4 5 3/4 21/2 3 10.0; 2.5
C-1010 1010 458 1.50 38 920 16.4 10 Green 73 92 121 229 133 127 19 64 76 10.0; 2.0
C-1265 1265 574 1.40 36 1265 23.0 Red 10.0; 1.6
714 1.63 41 1280 23.0 0.40 Pink
D-1575 1575 33/4 47/8 43/4 121/2 53/4 7 7/8 21/2 41/4 10.0; 6.0
975 1.43 36 2095 37.5 10 Purple 95 124 121 318 146 178 22 64 108 9.0; 4.4
D-2150 2150
1252 1.40 36 2760 50.1 0.40 Silver 4 /2 5 /8 6 14 /2 6 /4 7 /8 2 /2 5
1 1 1 1 7 1
F-2760 2760 5.0; 4.3
10 114 130 152 368 159 178 22 64 127
All springs have additional travel to solid equal to 50% of Rated Deflection. Hanger elements have straight line deflection curves. †includes double
deflection LDS element. ††applies to spring only. ;
10.0 indicates a rating of 10 G’s or greater 5
HS, PCHS, PCHSS & RWHS MASON INDUSTRIES
1"(25mm) Deflection X, A & B SPRING HANGERS
PCHS PCHSS RWHS
HS FOR ROD ATTACHMENT
TYPE HS
PRECOMPRESSED
TYPE HS PRECOMPRESSED
& SEISMIC RESTRAINT
TYPE HS
SEISMIC RESTRAINT
UPPER & LOWER UPPER ROD
RODS BY OTHERS BY OTHERS
BOLT TIGHT TO BOLT TIGHT TO
DEFLECTION STRUCTURE
SCALE STRUCTURE
UPPER
Clearance ROD BY
not Critical OTHERS
REINFORCE- Clearance UPPER &
MENT WHEN not LOWER RODS
H REQUIRED BY OTHERS
Critical
LDS RUBBER 1/4" DEFLECTION
SPRING CUP 2 Spring HS-2 (6mm) SCALE
LRP
with a projecting
bushing to 1/4" (6mm)
prevent steel REX
to steel
contact. Adjust nut
Adjust to provide
Precompression Seismic 1/4"(6mm)
nut to Rebound Steel
Plate. Hangers provide washer
are precom- and Bonded clearance Seismic
D 1/4”
LDS Rubber Rebound
pressed to rated (6mm) after
load or assigned Washer holds hanger is Steel and
plate precompres- Bonded
load as required. clearance fully
sion and limits loaded. LDS Rubber
W after upward seismic Washer limits
hanger motion. Hangers upward
STEEL DISK BONDED is fully are precom- seismic
TO LDS RUBBER loaded. pressed to rated motion.
4 Spring HS-4
1/4" Seismic load or assigned
(6mm) 1/2"
(13mm) Rebound load as required.
Washer Scale indicates
deflection.
Ratings & Dimensions for 1"(25mm) Deflection Spring Hangers (inches mm)
Spring Only Lower Max. Rod Vertical
Rated Rated Spring Spring Rod Rod Exten- ‘G’ Ratings
†
Capacity Defl. Constant Color/ Spring Free Penetration Dia. sion Com-
Type Size (lbs) (kg) (in) (mm) (lbs/in) (kg/mm) Stripe OD Height D H W LRP MRD REX Tension pression
X-12 12 5 1.25 32 10 0.18 Orange 10.0; 10.0;
X-23 23 10 1.30 33 18 0.30 Brown 10.0; 10.0;
X-33 33 15 1.10 28 30 0.54 Red 10.0; 10.0;
X-54 54 24 1.20 30 45 0.80 White 10.0; 10.0;
X-76 76 34 1.02 25 73 1.36 Black 11/2 21/2 21/2 41/4 27/8 31/2 3/8 13/4 10.0; 10.0;
X-113 113 51 1.00 25 113
2.04 Yellow 38 64 64 108 73 89 10 44 10.0; 7.6
X-130 130 59 1.00 25 130
2.36 Purple 10.0; 6.6
1" X-175 175 79 1.00 25 175
3.16 Silver 10.0; 4.9
25mm X-210 210 95 1.00 25 210 3.80 Blue 9.0 4.1
Defl. A-12 12 5 1.00 25 12 0.20 Red 10.0; 10.0;
13/4 17/8 23/4 53/4 31/4 31/2 5/8 21/4
A-18 18 8 1.00 25 18 0.32 Gray 10.0; 10.0;
0.44 Orange 44 48 70 146 83 89 16 57
A-25 25 11 1.00 25 25 10.0; 10.0;
A-41 41 19 1.18 30 35
0.63 Pink 10.0; 10.0;
A-56 56 25 1.14 30 49
0.83 Black 13/4 21/4 23/4 53/4 31/4 4 5/8 21/4 10.0; 10.0;
A-73 73 33 1.06 27 69
1.22 Tan 44 57 70 146 83 102 16 57 10.0; 10.0;
HS- A-95 95 43 1.01 26 94
1.65 Green 10.0; 10.0;
A-45 45 20 1.60 41 28 0.49 Blue 10.0; 10.0;
A-75 75 34 1.50 38 50 0.89 Orange 10.0; 10.0;
A-125 125 57 1.33 34 94 1.68 Brown 13/4 3 23/4 53/4 31/4 4 5/8 21/2 10.0; 10.0;
A-200 200 91 1.15 29 174 3.14 Black 44 76 70 146 83 102 16 64 10.0; 10.0;
PCHS- A-310 310 141 1.00 25 310 5.64 Yellow 10.0; 7.1
A-400 400 181 1.00 25 400
7.24 Green 10.0; 5.5
3 1 3 3 1 5 1
A-510 510 9.24 Red 1 /4 3 /8 2 /4 5 /4 3 /4 4 /8 2 /2
231 1.00 25 510 10.0; 4.3
44 79 70 146 83 102 16 64
3 3 3 3 1 5 1
A-625 625 11.3 White 1 /4 3 /8 2 /4 5 /4 3 /4 4 /8 2 /2
283 1.00 25 625 9.0 3.5
PCHSS- 44 86 70 146 83 102 16 64
B-65 65 29 2.10 53 31 0.55 Brown 10.0; 10.0;
B-85 85 39 2.10 53 40 0.74 White/Blk 10.0; 10.0;
B-115 115 52 2.00 51 57 1.02 Silver 10.0; 10.0;
1.33 Orange 2 /8 4
3 4 71/4 43/4 41/4 3/4 21/4
RWHS- B-150 150 68 2.00 51 75 10.0; 10.0;
60 102 102 184 121 108 19 57
B-280 280 127 1.60 41 174
3.10 Green 10.0; 5.4
B-450 450 204 1.31 33 344
6.18 Red 10.0; 3.3
B-750 750 340 1.12 28 670
12.1 White 10.0; 2.0
3 71/4 43/4 41/4 3/4 21/4
18.2 Blue 2 /8 4 4
454 1.00 25 1000
B-1000 1000 10.0; 1.5
60 102 102 184 121 108 14 57
6 †
All springs have additional travel to solid equal to 50% of the rated deflection. ;
10.0 indicates a rating of 10 G’s or greater
MASON INDUSTRIES HS, PCHS, PCHSS & RWHS
1"(25mm) DEFLECTION C AND MULTIPLE C SPRING HANGERS
Ratings & Dimensions for 1"(25mm) Deflection Spring Hangers (inches mm)
Spring Only Lower Max. Rod Vertical
Rated Rated Spring Rod Rod Exten- ‘G’ Ratings
†
Capacity Defl. Constant Spring Free Penetration Dia. sion Com-
Type Size (lbs) (kg) (in)(mm) (lbs/in) (kg/mm) Color OD Height D H W LRP MRD REX Tension pression
1-1000 1000 454 1.00 25 1000 18.2 Black 10.0; 3.2
1" 1-1350 1350 612 1.00 25 1350 24.5 Yellow 8.7 2.4
25mm 1-1750 1750 794 1.00 25 1750 31.8 Black* 6.7 1.8
2 7/8 41/8 4 83/4 51/4 5 7/8 21/4
Defl. 1-2100 2100 953 1.00 25 2100 38.1 Yellow* 5.6 1.5
73 105 102 222 133 127 22 57
1-2385 2385 1082 1.00 25 2385
43.3 Yellow** 5.0 1.4
1-2650 48.1 Red* 4.4 1.2
2650 1202 1.00 25 2650
HS- 1-2935 2935 1331 1.00 25 2935
53.2 Red** 4.0 1.1
2-2700 2700 1225 1.00 25 2700
49.0 Yellow 10.0; 3.0
63.5 Black* 2 /8 4 /8 9 10 5 /4 7 1 4 /4
7 1 1 1
PCHS- 2-3500 3500 1588 1.00 25 3500 10.0; 2.3
2-4200 76.2 Yellow* 73 105 229 254 133 178 25 108
4200 1905 1.00 25 4200 9.8 1.9
4-5400 5400 2449 1.00 25 5400
98.0 Yellow 10.0; 3.5
127.0 Black* 2 /8 4 /8 7 13 8 /8 7 1 /4 4 /2
7 1 7 1 1
PCHSS- 4-7000 7000 3175 1.00 25 7000 8.4 2.7
4-8400 152.4 Yellow* 73 105 178 330 225 178 32 114
8400 3810 1.00 25 8400 7.0 2.2
RWHS- 4-9540 9540 4327 1.00 25 9540 173.1 Yellow** 6.2 2.0
4-10600 10600 4808 1.00 25 10600 192.3 Red* 2 /8 4 /8 7 13 8 /8 7 1 /4 4 /2
7 1 7 1 1
5.5 1.8
73 105 178 330 225 178 32 114
4-11740 11740 5325 1.00 25 11740 213.0 Red** 5.0 1.6
†
All springs have additional travel to solid equal to 50% of the rated deflection. ;
10.0 indicates a rating of 10 G’s or greater
*with Red inner spring **with Green inner spring
Ratings & Dimensions for 1"(25mm) Deflection Spring and Double Deflection LDS Hangers (inches mm)
Average LRP– Lower Rod Penetration REX– Rod Extension Vertical
Spring Only
MRD– Max. Rod Diameter URP– Upper Rod
Rated Rated Spring Defl. Spring G Ratings
† ††
Capacity Defl. Constant LDS Color/
Free Penetration Com-
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Rubber Stripe OD Height D H W LRP MRD REX URP Tension pression
X-12 12 5 1.45 37 10 0.18 Orange 10.0; 10.0;
X-23 23 10 1.50 38 18 0.30 Brown 10.0; 10.0;
X-33 33 15 1.30 33 30 0.54 Red 10.0; 10.0;
9 . + * X-54 54 24 1.40 36 45 0.80 White 10.0; 10.0;
X-76 76 34 1.22 31 73 1.36 0.20 Black 11/2 21/2 21/2 51/2 27/8 31/4 3/8 13/4 13/4 10.0; 10.0;
1” X-113 113 51 1.20 30 113 2.04 5 Yellow 25 64 64 140 73 83 10 44 44 10.0; 6.7
25mm X-130 130 59 1.20 30 130 2.36 Purple 10.0; 5.8
79 1.20 30 175 3.16
Defl. X-175 175 Silver 10.0; 4.3
X-210 210 95 1.20 30 210 3.80 Blue 10.0; 3.6
5 1.35 34 12 0.20
A-12 12 Red 10.0; 10.0;
8 1.35 34 18 0.32 0.35 Gray 13/4 17/8 23/4 63/4 31/4 31/2 5/8 21/4 21/4 10.0; 10.0;
A-18 18
9 Orange 44 48 70 171 83 89 16 57 57 10.0; 10.0;
11 1.35 34 25 0.44
A-25 25
DNHS- A-41 19 1.53 39 35 0.63
41 Pink 10.0; 10.0;
A-56 56 25 1.49 38 49 0.83 0.35 Black 13/4 21/4 23/4 63/4 31/4 4 5/8 21/4 21/4 10.0; 10.0;
A-73 73 33 1.41 36 69 1.22 9 Tan 44 57 70 171 83 102 16 57 57 10.0; 10.0;
A-95 95 43 1.36 35 94 1.65 Green 10.0; 10.0;
A-45 45 20 1.95 50 28 0.49 Blue 10.0; 10.0;
PCDNHS- A-75 75 34 1.85 47 50 0.89 Orange 10.0; 10.0;
A-125 125 57 1.68 43 94 1.68 0.35 Brown 13/4 3 23/4 63/4 31/4 4 5/8 21/2 21/4 10.0; 10.0;
A-200 200 91 1.50 38 174 3.14 9 Black 44 76 70 171 83 102 16 64 57 10.0; 8.8
A-310 310 141 1.35 34 310 5.64 Yellow 10.0; 5.6
A-400 400 181 1.35 34 400 7.24 Green 10.0; 4.4
PCDNHSS- 0.35 Red 13/4 31/8 23/4 63/4 31/4 4 5/8 21/2 21/4
231 1.35 34 510 9.24
A-510 510 10.0; 3.4
9 44 79 70 171 83 102 16 64 57
0.35 3 3 3 3 1 5/8 21/2 21/4
283 1.35 34 625 11.3
A-625 625 White 1 /4 3 /8 2 /4 6 /4 3 /4 4 10.0; 2.8
9 44 86 70 171 83 102 16 64 57
B-65 65 29 2.45 62 31 0.55 Brown 10.0; 10.0;
RWDNHS- B-85 85 39 2.45 62 40 0.74 White/Blk 10.0; 10.0;
B-115 115 52 2.35 60 57 1.02 Silver 10.0; 10.0;
68 2.35 60 75 1.33 0.35 Orange 2 /8 4 4 9 4 /4 4 /4
3 3 1 3/4 21/4 3
B-150 150 10.0; 10.0;
9 Green 60 102 102 229 121 108 19 57 76 10.0; 8.2
B-280 280 127 1.95 50 174 3.10
B-450 450 204 1.66 42 344 6.18 Red 10.0; 5.1
B-750 750 340 1.47 37 670 12.1 White 10.0; 3.1
3 3 1 3/4 21/4 3
B-1000 1000 454 1.35 34 1000 18.2 0.35 Blue 2 /8 4 4 9 4 /4 4 /4 10.0; 2.3
9 60 102 102 229 121 108 19 57 76
All springs have additional travel to solid equal to 50% of Rated Deflection. LDS elements have straight line deflection curves.
8 †
includes double deflection LDS element. ††applies to spring only. ;10.0 indicates a rating of 10 G’s or greater
MASON INDUSTRIES DNHS, PCDNHS, PCDNHS & RWDNHS
1"(25mm) DEFLECTION C & MULTIPLE C SPRING and DOUBLE DEFLECTION LDS HANGERS
Ratings & Dimensions for 1" (25mm) Deflection Spring and Double Deflection LDS Hangers (inches mm)
Average LRP– Lower Rod Penetration REX– Rod Extension Vertical
Rated Rated Spring Defl. Spring Only
MRD– Max. Rod Diameter URP– Upper Rod G Ratings
† ††
Capacity Defl. Constant LDS Spring
Free Extension Com-
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Rubber Color OD Height D H W LRP MRD REX URP Tension pression
1-1000 1000 454 1.40 36 1000 18.2 Black 10.0; 7.3
1-1350 1350 612 1.40 36 1350 24.5 Yellow 10.0; 5.4
1" 1-1750 1750 794 1.40 36 1750 31.8 Black* 10.0; 4.2
2100 953 1.40 36 2100 38.1 0.40 Yellow* 2 /8 4 /8 4 11 5 /4 5 /8 2 /4 3 /4
7 1 1 7 1 1
25mm 1-2100 8.4 3.5
10 Yellow** 73 105 102 279 133 127 22 57 83
Defl. 1-2385 2385 1082 1.40 36 2385 43.3 7.4 3.1
1-2650 2650 1202 1.40 36 2650 48.1 Red* 6.6 2.8
DNHS- 1-2935 2935 1331 1.40 36 2935 53.2 Red** 6.0 2.5
2-2700 2700 1225 1.40 36 2700 49.0 Yellow 10.0; 4.5
3500 1588 1.40 36 3500 63.5 0.40 Black* 27/8 41/8 9 12 51/4 7 1 41/4 33/4 10.0; 3.5
PCDNHS- 2-3500
10 Yellow* 73 105 229 305 133 178 25 108 95 10.0; 2.9
2-4200 4200 1905 1.40 36 4200 76.2
PCDNHSS- 4-5400 5400 2449 1.40 36 5400 98.0 Yellow 10.0; 5.0
7000 3175 1.40 36 7000 127.0 0.40 Black* 27/8 41/8 7 15 87/8 7 11/4 41/2 6 8.4 3.9
4-7000
8400 3810 1.40 36 8400 152.4 10 Yellow* 73 105 178 381 225 178 32 114 152
4-8400 7.0 3.2
RWDNHS- 4-9540 9540 4327 1.40 36 9540 173.1 Yellow** 6.2 2.8
4-10600 10600 4808 1.40 36 10600 192.3 0.40 Red* 27/8 41/8 7 15 87/8 7 11/4 41/2 6 5.5 2.6
10 73 105 178 381 225 178 32 114 152
4-11740 11740 5325 1.40 36 11740 213.0 Red** 5.0 2.3
All springs have additional travel to solid equal to 50% of Rated Deflection. LDS elements have straight line deflection curves.
*with Red inner spring **with Green inner spring †
includes double deflection LDS element. ††applies to spring only.
10.0 indicates a rating of 10 G’s or greater
;
2"(51mm) DEFLECTION B, B2, C2 & MULTIPLE C2 SPRING and DOUBLE DEFLECTION LDS HANGERS
Ratings & Dimensions for 2"(51mm) Deflection Spring and Double Deflection LDS Hangers (inches mm)
Average LRP– Lower Rod Penetration REX– Rod Extension Vertical
Spring Only
MRD– Max. Rod Diameter URP– Upper Rod
Rated Rated Spring Defl. Spring G Ratings
† ††
Capacity Defl. Constant LDS Color/ Free Extension Com-
Type Size (lbs) (kg) (in) (mm) (lbs/in)(kg/mm) Rubber Stripe OD Height D H W LRP MRD REX URP Tension pression
B-20 20 9 2.75 70 8 0.15 Tan 10.0; 10.0;
B-26 26 12 2.53 64 12 0.22 White/Bl 10.0; 10.0;
B-35 35 16 2.55 65 16 0.29 Purple 10.0; 10.0;
B-50 50 23 2.55 65 24 0.41 0.35 White/Rd 23/8 4 4 9 43/4 51/8 3/4 21/4 3 10.0; 10.0;
2" B-65 65 29 2.45 62 31 0.55 9 Brown 60 102 102 229 121 130 19 57 76 10.0; 10.0;
51mm B-85 85 39 2.45 62 40 0.74 White/Blk 10.0; 10.0;
Defl. B-115 115 52 2.35 60 57 1.02 Silver 10.0; 10.0;
B-150 150 68 2.35 60 75 1.33 Orange 10.0; 10.0;
B2-210 210 95 2.47 63 99 1.76 Silver 10.0; 10.0;
B2-290 290 132 2.35 60 144 2.59 0.35 Blue 23/8 41/2 4 9 43/4 51/8 3/4 21/4 3 10.0; 8.0
B2-450‡ 450 204 2.35 60 224 4.00 9 Tan 60 114 102 229 121 130 19 57 76 10.0; 5.1
DNHS- B2-680‡ 680 308 2.35 60 340 6.04 Gray 10.0; 3.4
C2-125 125 57 2.90 74 50 0.89 Purple 10.0; 10.0;
C2-170 170 77 2.80 71 70 1.26 Brown 10.0; 10.0;
C2-210 210 95 2.70 69 90 1.64 Red 10.0; 10.0;
C2-260 260 118 2.60 66 120 2.11 White 10.0; 10.0;
PCDNHS- C2-330 330 150 2.40 61 165 2.94 Black 10.0 27/8 5 4 11 51/4 51/4 7/8 21/4 31/4 10.0; 10.0
; ;
277 2.40 61 305 5.43 10 Green 73 127 102 279 133 133 22 57 83 10.0; 10.0;
C2-610 610
C2-880‡ 880 399 2.40 61 440 7.82 Gray 10.0; 8.3
C2-1210‡ 1210 549 2.40 61 605 10.8 Silver 10.0; 6.0
PCDNHSS- C2-1540‡ 1540 699 2.40 61 770 13.7 Gray* 10.0; 4.7
C2-1870‡ 1870 848 2.40 61 935 16.6 Silver* 9.4 3.9
2-C2-2420‡ 2420 1098 2.40 61 1210 21.5 Silver 10.0 27/8 5 9 12 51/4 6 1 41/4 33/4 10.0; 5.1
;
2-C2-3080‡ 3080 1397 2.40 61 1540 27.4 0.40 Gray * 73 127 229 305 133 154 25 108 95 10.0; 4.0
RWDNHS- 2-C2-3740‡ 3740 1696 2.40 61 1870 33.3 10 Silver* 3.3
4-C2-3520‡ 3520 1597 2.40 61 1760 31.3 Gray 10.0; 7.7
4-C2-4840‡ 4840 2195 2.40 61 2480 43.0 0.40 Silver 27/8 5 7 15 87/8 8 11/4 41/2 6 10.0; 5.6
4-C2-6160‡ 6160 2794 2.40 61 3080 54.8 10 Gray* 73 127 178 381 225 203 32 114 152 9.5 4.4
4-C2-7480‡ 7480 3393 2.40 61 3740 66.5 Silver* 7.8 3.6
All springs without “‡" have additional travel to solid equal to 50% of Rated Deflection. LDS elements have straight line deflection curves.
*with Red inner spring ;
10.0 indicates a rating of 10 G’s or greater
†
includes double deflection LDS element. ††applies to spring only.
‡
Published ratings allow minimum 25% additional travel to solid. For a full 50% specified minimum use the following ratings:
Derated Derated Derated
Capacity Defl. Capacity Defl. Capacity Defl.
Size (Ibs) (kg) (in) (mm) Size (Ibs) (kg) (in) (mm) Size (Ibs) (kg) (in) (mm)
B2-450 410 186 1.83 46 C2-1870 1560 708 1.67 42 2-C2-3740 3120 1415 1.67 42
B2-680 565 256 1.66 42 2-C2-1760 1600 726 1.82 46 4-C2-4840 4040 1833 1.67 42
C2-880 800 363 1.82 46 2-C2-2420 2020 916 1.67 42 4-C2-6160 5145 2334 1.67 42
C2-1210 1010 458 1.67 42 2-C2-3080 2570 1166 1.67 42 4-C2-7480 6245 2833 1.67 42
C2-1540 1285 583 1.67 42 9
30N-100, PC30N-100, PC30NS-100 & RW30N-100 MASON INDUSTRIES
2"(51mm), 3"(76mm), 4"(102mm) & 5"(127mm) DEFLECTION 30° SWING - 100 SERIES SPRING and
DOUBLE DEFLECTION LDS HANGERS
D 1/4"
REX REX (6mm)
RW30N- 162 5100 2313 4.78 121 1155 20.8 0.40 Blue/Or 83/4 222 111/2 292 10 261/2 121/2 19 11/8 1 61/2 61/2
3 1 6.6 1.3
163 6500 2948 4.78 121 1485 26.6 10 Blue/Wh 8 /4 222 13 /4 337 254 673 318 483 29 25 165 165 5.2 1.1
164 8400 3810 4.78 121 1910 34.3 Blue/Sil 83/4 222 133/8 340 4.0 0.81
1 1 1 1
165 10800 4899 4.78 121 2455 44.4 0.40 Blue/Gy 93/8 238 141/8 359 10 28 12 /4 21 1 /8 1 6 /2 6 /2 4.0 0.6
10 254 711 311 533 29 25 165 165
122 5.71 145 50
174 270 0.89 Purple 6 152 97/8 251 10.0; 10.0;
145 5.71 145 60
175 320 1.70 0.40 Brown 6 152 101/16256 10.0; 10.0;
6 152 100/0 254 7 16 9 /4 12 /2 /4 /8 5 3 /4
1 1 3 5 1
168 5.71 145 70
176 370 1.25 10 Orange 10.0; 9.4
209 5.78 147 85
177 460 1.50 Green 6 152 101/2 267 178 406 235 318 19 16 127 83 10.0; 7.6
254 5.78 147 105
178 560 1.90 Red 6 152 103/4 273 10.0; 6.2
5" 179 670 304 5.78 147 125
2.20 White 63/4 171 111/16281 10.0; 10.0;
127mm 180 830 376 5.78 147 155
2.80 0.40 Blue 63/4 171 113/8 289 8 19 10 15 3/4 5/8 51/2 31/2 10.0; 10.0;
Defl. 181 1000
454 5.78 147 185
3.30 10 Black 63/4 171 111/8 283 203 483 254 381 19 16 140 89 10.0; 9.1
562 5.77 147 230
182 1240 4.10 Yellow 63/4 171 113/8 289 10.0; 7.3
30N- 183 1500 680 5.77 147 280 5.00 Gray 73/4 197 127/16316 10.0; 6.0
184 1830 830 5.77 147 340 6.10 0.40 Pink 73/4 197 117/8 302 9 21 111/4 17 7/8 3/4 6 31/2 10.0; 4.9
PC30N- 185 2230 1012 5.77 147 415
7.40 10 Silver 73/4 197 120/0 305 229 533 286 432 22 19 152 89 10.0; 4.0
186 2710 1229 5.77 147 505
9.00 Tan 73/4 197 123/4 324 9.0 3.3
PC30NS- 187 3300 1497 5.77 147 615
11.0 0.40 Blue/Or 83/4 222 123/4 324 10.0; 2.1
13.6 10 Blue/Rd 83/4 222 133/8 340 9 /2 26 /2 12 /4 19 /8 /8 6 6 /2
1 1 1 7 7 1
188 4100 1860 5.77 147 755 9.6 1.7
RW30N- 189 4900 2223 5.77 147 915 16.3 Blue/Wt 91/16 230 137/16341 241 673 311 483 22 22 152 165 8.0 1.4
2722 5.77 147 1120 20.0 0.40 Blue/Yel 91/2 241 145/8 371 10 28 121/4 21 11/8 1 61/2 61/2 7.3 1.1
190 6000
3311 5.77 147 1365 24.3 10 Blue/Sil 91/2 241 153/16386 254 711 311 533 29 25 165 165 6.0 0.85
191 7300
192 9000 4082 5.77 147 1670 29.9 0.40 Blue/Gy 101/4 260 155/8 397 101/2 30 131/4 23 11/8 1 61/2 61/2 3.7 0.6
193 11000 4990 5.77 147 2040 36.6 10 Blue/Tn 101/4 260 160/0 406 267 762 337 584 29 25 165 165 3.0 0.5
All springs have additional travel to solid equal to 50% of Rated Deflection. LDS elements have straight line deflection curves.
† ††
includes double deflection LDS element. applies to spring only. ;
10.0 indicates a rating of 10 G’s or greater.
11
1000 30N
3"(76mm) & 4"(102mm) DEFLECTION 30° SWING – LOW CAPACITY 1000 SERIES SPRING and
DOUBLE DEFLECTION LDS HANGERS
30N-1000 3" FOR ROD ATTACHMENT 30N-1000 4" FOR ROD ATTACHMENT
W
DOUBLE DEFLECTION DOUBLE
LDS RUBBER ELEMENT DEFLECTION
with projecting bushing LDS RUBBER
ELEMENT with
projecting
3/8"(10mm) Welded Nut under Spring bushing
Top Cup and a 3/8"(10mm) loose nut URP
URP above the Spring Top Cup to lock the UPPER &
Lower Rod in place. LOWER
UPPER & LOWER RODS BY
H RODS BY OTHERS H OTHERS
HES Hangers are installed at riser suspension points to control load shifts as
100% MOVEMENT the riser expands or contracts. If a 120 foot(37m) steel riser goes through 50% MOVEMENT
a temperature increase of 150°F(66°C), the piping will expand 1.4"(36mm).
If the piping had an anchor point in the basement, the piping bracket at VSG
GUIDES See
the 60’(18m) elevation and the top bracket would rise 0.7"(18mm) and Data Sheet
1.4"(36mm), respectively. This travel would transfer the entire piping weight to DS-510
the basement as the piping would lift off non-resilient support points. Standard
1"(25mm) deflection hangers would lose 70% of their load at the 60 foot(18m)
point and the complete load at the top of the run. Therefore, HES Hangers are
needed because of their higher initial deflection and travel capability. If HES
Hangers with 4"(102mm) initial deflection were selected, the hanger at the top
would lose only 35% of its load and the intermediate hanger only 18%. This
VSG
GUIDES See would substantially reduce the load shift to the basement anchor.
Data Sheet
DS-510 Special larger deflection hangers would be even more effective. In handling TYPE HES
this type of problem, it is preferable to anchor the riser at the center of the run. EXPANSION
HANGER
If this had been done in the piping problem described above, each end would
have expanded outward only 0.7"(18mm) instead of the 1.4"(36mm). The ADA ANCHORS See PIPE
TYPE HES upper hangers would have lost 18% of their load since the springs would be Data Sheet DS-510 BRACKET
EXPANSION unloaded the 0.7(18mm) of an inch.
HANGER
The springs in the hangers on the lower end of the piping would have been HOT COLD
compressed 0.7(18mm) of an inch thereby increasing their load by 18%. With
this loss and gain situation, the piping always remains balanced at the neutral
PIPE
BRACKET point.
EXAMPLE–
6"(152mm) Schedule 40 piping weighing 36 pound per foot(4.94kg/m) with
water. The run of 120 feet(37m) would weight a total of 4320 pounds (1960
kgs). If the piping is anchored at the center we might select support points
at the lower end, the 30 foot(9m) and 90 foot(27m) marks and at the top.
Therefore, we would have 4 locations or a total of 8 hangers supporting
504 pounds(229kg) each. The preliminary selection would be 8 HESB-
HOT 750 Hangers. The initial hanger deflection would be 540 pounds(245kg) VSG GUIDES
divided by the spring constant of 167 pound/inch(2.98 kg/mm) which equals
COLD 3.23"(82mm). The total spring deflection would be the initial deflection
ND LDS or SLRS plus the expansion travel or 3.23"(82mm) plus 0.7"(18mm) which equals
PIPE ANCHOR
ASSEMBLY 3.93"(100mm). The hanger must then be checked to see if this deflection is 50%
within the range of the selected hanger. Since the HES Hangers can over MOVEMENT
Floor capacity inade- travel the rated deflection by 40% the HESB-750 can travel 4.50(114mm)
quate for total load. X 1.4(36mm) or 6.30"(160mm). Therefore, the selection is correct. If this
number were smaller than the required 3.93(100mm) it would be necessary to
PIPE ANCHORED use the next larger hanger and check again. (Actually this hanger needed no PIPE ANCHORED
AT ONE END checking as the 4.50"(114mm) rated deflection already met the conditions). AT MID POINT
Piping installed at ambient temperature, expansion movement is directed away from the anchor at higher steam or water temperatures
and toward the anchor when chilled water is circulated. 13
IM HANGERS MASON INDUSTRIES
LDS
RUBBER
SPRING “RP"
CUP ROD
PENETRATION Pipe Trapeze Cradled Unit
STEEL CUP
Ratings & Dimensions for 1"(25mm) Deflection Simple Spring Hangers (inches mm)
Spring Only Bushing Cup Max.
Rated Rated Spring Outside Outside Rod Rod
Capacity Defl. Constant Spring Free Dia. Dia. Dia Penetration
Type Size (lbs) (kg) (in) (mm) (lbs/in) (kg/mm) Color OD Height BOD COD MRD RP
X-12 12 5 1.25 32 10 0.18 Orange
X-23 23 10 1.30
33 18 0.30 Brown
X-33 33 15 1.10
28 30 0.54 Red
X-54 54 24 1.20
30 45 0.80 White
X-76 76 34 1.02
25 73 1.36 Black 11/2 21/2 11/8 2 3/8 23/4
X-113 113 51 1.00
25 113
2.04 Yellow 38 64 29 51 10 69
X-130 130 59 1.00
25 130
2.36 Purple
X-175 175 79 1.00
25 175
3.16 Silver
X-210 210 95 1.00
25 210
3.80 Blue
A-12 12 5 1.00 25 12
0.20 Red
13/4 17/8 11/4 21/2 3/8 21/4
A-18 18 8 1.00 25 18
0.32 Gray
A-25 25 11 1.00 0.44 Orange 44 48 32 64 10 57
25 25
1” A-45 45 20 1.60 41 28 0.49 Blue
25mm A-75 75 34 1.50 38 50 0.89 Orange
Defl. A-125 125 57 1.33 34 94 1.68 Brown 13/4 3 11/4 21/2 1/2 33/8
A-200 200 91 1.15 29 174
3.14 Black 44 76 32 64 13 86
IM- A-310 310 141 1.00 25 310
5.64 Yellow
A-400 400 181 1.00 25 400
7.24 Green
13/4 31/8 11/4 21/2 1/2 31/2
231 1.00
A-510 510 25 510
9.24 Red
44 79 32 64 13 89
3 3 1 1 1/2 33/4
283 1.00
A-625 625 11.3 White 1 /4 3 /8 1 /4 2 /2
25 625
44 86 32 64 13 95
B-65 65 29 2.10 53 31 0.55 Brown
B-85 85 39 2.10 53 40 0.74 White/Blk
B-115 115 52 2.00 51 57 1.02 Silver
B-150 150 68 2.00 51 75 1.33 Orange
B-280 280 127 1.60 41 174 3.10 Green 23/8 4 17/8 31/8 3/4 5
B-450 450 204 1.31 33 344 6.18 Red 60 102 48 79 19 127
B-750 750 340 1.12 28 670 12.1 White
B-1000 1000 454 1.00 25 1000
18.2 Blue
B-1250 1250 567 1.00 25 1250
22.7 Gray
B-1650 1650 748 1.00 25 1650
29.9 Black
C-1000 1000 454 1.00 25 1000
18.2 Black
C-1350 1350 612 1.00 25 1350
24.5 Yellow
C-1750 1750 794 1.00 31.8 Black*
25 1750
27/8 41/8 23/8 35/8 3/4 5
C-2100 2100 953 1.00 38.1 Yellow*
25 2100
73 105 60 92 19 127
C-2385 43.3 Yellow**
2385 1082 1.00 25 2385
C-2650 48.1 Red*
2650 1202 1.00 25 2650
C-2935 53.2 Red**
2935 1331 1.00 25 2935
All springs have additional travel to solid equal to 50% of Rated Deflection.
14 *with Red inner spring **with Green inner spring
MASON INDUSTRIES IM, HD & RWHD
IM 2"(51mm) DEFLECTION B, B2, C2 & MULTIPLE C2 SIMPLE SPRING HANGERS
Ratings & Dimensions for 2"(51mm) Deflection Simple Spring Hangers (inches mm)
Spring Only Bushing Cup Max.
Rated Rated Spring Spring Outside Outside Rod Rod
Capacity Defl. Constant Color/ Spring Free Dia. Dia. Dia Penetration
Type Size (lbs) (kg) (in) (mm) (lbs/in) (kg/mm) Stripe OD Height BOD COD MRD RP ‡
Published ratings
allow minimum 25%
B-20 20 9 2.40 61 8 0.15 Tan additional travel to
B-26 26 12 2.18
55 12
0.22 White/Blue solid. For a full 50%
B-35 35 16 2.20
56 16
0.29 Purple specified minimum use
B-50 50 23 2.20
56 24
0.41 White/Red 23/8 4 17/8 31/8 3/4 47/8 the following ratings:
B-65 65 29 2.10
53 31
0.55 Brown
60 102 48 79 19 124 Derated
B-85 85 39 2.10
53 40
0.74 White/Black Capacity Defl.
B-115 115 52 2.00
51 57
1.02 Silver Size (Ibs) (in)
B-150 150 68 2.00
51 75
1.33 Orange
B2-450 410 1.83
B2-210 210 95 2.12 54 99 1.76 Silver B2-680 565 1.66
2" B2-290 290 132 2.00
51 144
2.59 Blue 23/8 41/2 17/8 31/8 3/4 53/8
C2-880 800 1.82
51mm B2-450‡ 450 204 2.00
51 224
4.00 Tan 60 114 48 79 19 137 C2-1210 1010 1.67
Defl. B2-680‡ 680 308 2.00
51 340
6.04 Gray C2-1540 1285 1.67
C2-125 125 57 2.50 64 50 0.89 Purple C2-1870 1560 1.67
IM- C2-170 170 77 2.40 61 70 1.26 Brown
C2-210 210 95 2.30 58 90 1.64 Red Derated
C2-260 260 118 2.20
56 120
2.11 White Capacity Defl.
Size (kg) (mm)
C2-330 330 150 2.00
51 165
2.94 Black
27/8 5 23/8 35/8 3/4 57/8
B2-450 186 46
C2-460 460 209 2.00
51 230
4.10 Blue
73 127 60 92 19 149 B2-680 256 42
C2-610 610 277 2.00
51 305
5.43 Green
C2-880‡ 880 399 2.00
51 440
7.83 Gray C2-880 363 46
‡
C2-1210 1210 549 2.00 51 605
10.8 Silver C2-1210 458 42
‡
C2-1540 1540 699 2.00 13.7 Gray*
51 770 C2-1540 583 42
C2-1870‡ 1870 848 2.00 16.6 Silver*
51 935 C2-1870 708 42
All springs without “‡" have additional travel to solid equal to 50% of Rated Deflection. *with Red inner spring
BOLT TIGHT TO
STRUCTURE
UPPER & LOWER
RODS BY OTHERS
UPPER &
DOUBLE DEFLECTION LOWER
H LDS RUBBER ELEMENT RODS BY
with a projecting bushing to OTHERS
prevent steel to steel contact.
LRP
1/4"(6mm)
H
LRP Seismic Rebound Steel Adjust nut to
and Bonded LDS provide 1/4"(6mm)
D washer clearance
Rubber Washer limits
D upward seismic motion. after hanger is
W SIZES HD fully loaded.
& HD-A STEEL DISK BONDED
SIZES HD-B thru DS W
TO LDS RUBBER
1/4" Seismic
(6mm) 1/2"
(13mm) Rebound
Ratings & Dimensions for LDS Hangers (inches mm) Washer
Rated Max Lower Max. Vertical
Size Capacity Rated Rod Rod G Ratings
(Color Duro- Range Defl† Penetration Dia. Com-
Type Mark) meter (Ibs) (mm) (in) (mm) D H W LRP MRD Tension pression
Green 40 Up to 35 Up to 16 0.20 5 13/4 44 21/4 57 17/8 48 11/4 32 3/8 10 10.0; 10.0;
White 60 35-75 16-34 0.20 5 10.0; 6.3
A-Black 30 Up to 45 Up to 20 0.35 9 10.0; 10.0;
A-Green 40 30-75 14-34 0.35 9 21/4 51 23/4 70 21/4 57 21/4 57 1/2 13 10.0; 8.5
HD- A-Red 50 60-125 27-573 0.35 9 10.0; 5.1
B-Red 50 Up to 235 Up to 107 0.40 10 10.0; 10.0;
B-White 60 180-380 82-1723 0.40 10 31/4 83 41/2 114 41/4 108 31/4 76 3/4 19 10.0; 6.7
RWHD- B-Yellow 70 320-650 145-295 0.40 10 10.0; 3.9
BS-Blue 70 500-1000 227-454 0.40 10 31/4 83 41/2 114 41/4 108 31/4 76 3/4 19 10.0; 2.3
CS-Blue 70 1000-2100 454-95333 0.40 10 31/4 83 51/4 127 41/4 108 31/4 83 7/8 22 9.0 1.2
DS-Blue 70 2100-4200 953-19053 0.40 10 41/4 102 61/4 159 43/4 121 31/4 83 7/8 22 5.0 1.0
†
includes double deflection LDS element. Hanger elements have straight line deflection curves. 10.0 indicates a rating of 10 G’s or greater.
;
15
WHR & W MASON INDUSTRIES
WHR 0.2"(5mm) DEFLECTION LDS CEILING HANGERS for Wire or Horizontal Attachment
All Metal Parts are Clearance for
Zinc Electroplated 3/16"(5mm) dia. NOTE –
Wire,Bolt, Nail or Tested to Failure at 1200 lbs.(544 kgs)
Screw
Projecting bushing
prevents metal to
metal contact.
For a complete presentation of Mason Ceiling Hangers, please refer to Bulletin CH-620 in the Architectural section.
4’-0" 4’-0"
1.2 m 1.2 m
Typical
Spacing
Secured by Wire Bolted to Ceiling Channel Bolted to Straps TYPE W as Ceiling Hangers
PRODUCT FINISHES
All standard products have a painted or powder coated finish unless otherwise indicated.
Springs are powder coated or zinc electroplated.
All hangers can be manufactured in stainless steel or hot dipped galvanized at additional
cost.
MASON INDUSTRIES, INC.
350 Rabro Drive,Hauppauge, NY 11788 • 631/348-0282 • FAX 631/348-0279
2101 W. Crescent Ave., Suite D • Anaheim, CA 92801 • 714/535-2727 • FAX 714/535-5738 Wu1606
16 Email info@Mason-Ind.com • Website www.Mason-Ind.com 6/16