Вы находитесь на странице: 1из 235

LATEST PRE-BOARD EXAM COMPILATION

ENGINEERING SCIENCES AND ALLIED SUBJECTS


AUGUST 2012 – JULY 2018

WITH QUESTION AND SOLUTION

RIZAL TECHNOLOGICAL UNIVERSITY


MAY 2019
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

TABLE OF CONTENTS

ESAS PRE-BOARD EXAM JULY 2018........................................................................... 2

ESAS PRE-BOARD EXAM MARCH 2018 .................................................................... 17

ESAS PRE-BOARD EXAM AUGUST 2017 .................................................................. 33

ESAS PRE-BOARD EXAM MARCH 2017 .................................................................... 49

ESAS PRE-BOARD EXAM AUGUST 2016 .................................................................. 62

ESAS PRE-BOARD EXAM MARCH 2016 .................................................................... 81

ESAS PRE-BOARD EXAM AUGUST 2015 .................................................................. 95

ESAS PRE-BOARD EXAM MARCH 2015 .................................................................. 115

ESAS PRE-BOARD EXAM AUGUST 2014 ................................................................ 132

ESAS PRE-BOARD EXAM MARCH 2014 .................................................................. 146

ESAS PRE-BOARD EXAM AUGUST 2013 ................................................................ 167

ESAS PRE-BOARD EXAM MARCH 2013 .................................................................. 190

ESAS PRE-BOARD EXAM AUGUST 2012 ................................................................ 213


REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM JULY 2018

1. Mr. Juan dela Cruz drives 120 km at 100km/h and 120 km at 90 km/h. What is the
average speed of Mr. dela Cruz on this trip in km/h?
A. 93.5 B. 94.7 C. 85.8 D. 82.3

Solution:

120 + 120
𝐴𝑣𝑒. 𝑠𝑝𝑒𝑒𝑑 = 𝑑𝑖𝑠𝑡𝑎𝑛𝑐𝑒⁄𝑡𝑖𝑚𝑒 = = 𝟗𝟒. 𝟕
120 120
100 + 90

2. In a spreadsheet (EXCEL), the number in cell A2 is set to 2. Then cell B2 is set to


A2 x 4 / $A$2, where $ indicates the absolute cell address. This formula is copied
into cells C2 and D2. What is the value shown in cell D2?
A. 8 B. 2 C. 4 D. 16
Solution:
A2 x 4 / $A$2 B2 x 4 / $A$2 C2 x 4 / $A$2
2 4 4
4∗2= 4 4∗2= 8 8 ∗ 2 = 𝟏𝟔

3. What is the MOST nearly effective annual interest rate on a loan if the nominal
interest rate is 9% per year compounded quarterly?
A. 9.52% B. 9.84% C. 9.68% D. 9.31%
Solution:
𝑟 0.09
𝐸𝑅𝐼 = (1 + )𝑚 – 1 = (1 + )4 – 1 = 0.0931 𝑥 100% = 𝟗. 𝟑𝟏%
𝑚 4
4. Find the amount of P30,000 at 6% simple interest after 5 years.
A. P39,000 B. P40,000 C. P41,000 D. P42,000
Solution:
𝐹 = 𝑃 ( 1 + 𝑖𝑛) = 30,000 (1 + 0.06𝑥5) = 𝑷𝟑𝟗, 𝟎𝟎𝟎

5. A bar of uniform cross section is subject to a uniaxial tension and develops a strain
in the direction of the force 1/800. Calculate the change of volume per unit volume.
Assume µ= 1/3.
A. 1/2400 (inc) B. 1/2400 (dec) C. 1/1200 (inc) D. 1/1200 (dec)

2
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

∆𝑣
= ∈ 𝑎𝑥𝑖𝑎𝑙 (1 − 2𝜇)
𝑣
∆𝑣 1 1 𝟏
= (1 − 2 ∗ = (𝒊𝒏𝒄)
𝑣 1800 3 𝟐𝟒𝟎𝟎

6. A bank is advertising 9.5 percent account that yield 9.84 percent annually. Find how
often interest is compounded.
A. Monthly B. Bimonthly C. Quarterly D. Annually

7. Defects seen by optical or electron microscope.


A. alteration B. aberration C. atomization D. deformation

8. NGCP warns ___________ alert if tropical disturbance is expected to make a


landfall within 24hrs.
A. yellow B. blue C. red D. weather disturbance

9. What is work-in process classified as


A. an asset B. a liability C. an expense D. owner’s equity

10. It state that if two bodies are in thermal equilibrium with a third body, they are also in
thermal equilibrium with each other.
A. first law of thermodynamics C. third law of thermodynamics
B. zeroth law of thermodynamics D. second law of thermodynamics

11. The circuit conductors between the final overcurrent device protecting the circuit and
the outlet(s).
A. Feeder C. Branch Circuit
B. Service lateral D. Service conductor

12. The term “thermodynamics” comes from the Greek words “Therme” and “Dynamis”
which means
A. heat, power C. heat, transfer
B. heat, motion D. heat, energy

3
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
13. If a refrigerator uses 1.5kJ to cool a 1kJ input. What was the heat transferred to the
kitchen?
A. 1kJ B. 2kJ C. 0.5kJ D. 2.5kJ

Solution:
𝑤 = 𝑄𝐻 – 𝑄𝐿
𝑄𝐻 = 𝑤 + 𝑄𝐿 = 1.5 + 1 = 𝟐. 𝟓𝒌𝑱

14. A mass m is released at a height h, using conservation of energy, find the final
velocity of the mass as it hits the ground.
A. v = gh B. v= gh/ 2 C. v= √𝟐𝒈𝒉 D. v= √𝑔ℎ

15. A conducting connections, whether intentional or accidental, between an electrical


circuit or equipment and the earth, or to some conducting body that serves in place
of the earth.
A. Grounded B. Ground C. Short D. Fault

16. An essential part of a large dam and provides an efficient and safe means of
releasing flow of water that exceeds the design capacity of the reservoir.
A. spillway B. weir C. culverts D. standpipe

17. The maximum bending moment in a simple supported beam of span L and carrying
a concentrated load “W” is
A. WL B. WL/ 2 C. WL/ 4 D. 2WL

18. MS-DOS is a type of?


A. system software C. application software
B. operating system D. system architecture

19. (111) base 2 + (111) base 2 = ( ) base 2.


A. 11011 B. 11101 C. 11110 D. 11100

Solution:
1112 + 1112 = ________2
1112
+1112
111102

4
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
20. The ampacity of the fuse should be 125% of the continuous load current is covered
by
A. installation design C. manufacturing design
B. wiring design D. construction design

21. Steel that are used for axles, gears and similar parts requiring medium to high
hardness and high strength are known as
A. Low- carbon steels C. High-carbon steels
B. Medium-carbon steels D. Very high-carbon steel

22. What will you do when you install a new heat sink?
A. Insert thermal compound between processor and system board.
B. Apply isopropyl alcohol between processor and heat sink.
C. Insert thermal compound between processor and heat sink.
D. Apply isopropyl alcohol between processor and system board.

23. Assuming i= annual rate of return, n= number of years, F= future worth, and
P= present worth, what is the future worth of a present amount P(F/P, I, n).
A. P( 1+ i)n B. P( 1+ i)n-1 C. P( 1+ i)-n D. P( 1+ i)i

24. Which of the following statements is not correct?

A. A nominal rate of 12% per annum compounded quarterly is the same as (12%) +
4 = 3% per quarter.
B. One dollar compounded quarterly at 3% for n years has a worth of (1.03) 4n
dollars.
C. Compounding quarterly at a nominal rate of 12% per year is equivalent to
compounding annually at a rate of 12.55%.
D. Effective rate of return in choices (A) through (C) is the difference between
12.55% and 12%.

25. XYZ Corporation is applying for a short term loan. In reviewing XYZ Corporation’s
financial records, bank ABC finds a current ratio of 2.0, an acid test ratio of 0.5, and
an account receivable period of 70 days. What should the banker do?

I. suggest that XYZ Corporation lower its inventories


II. suggest that XYZ Corporation be more aggressive in collecting on its invoices
A.I only B. II only C. either I or II D. both I or II
26. The ideal, reversible Carnot cycle involve four basic processes. What type of

5
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
processes are they?
A. all isothermal C. two adiabatic and two isentropic
B. all adiabatic D. two isothermal and two isentropic

27. What is the value of A after this program segment is performed?

A= 0
DO 77 I = 1, 4
77 A= A + I

A. 4 B. 5 C. 8 D. 10
Solution:
I= 0 A=0
A= A + I= 0+1 = 1
I= 2 A=1
A= A + I= 1+2 = 3
I=3 A=3
A= A + I= 3+3= 6
I=4 A=6
A= A + I= 6+4= 10
28. Formula for calcium chloride
A. CaCl2 B. Ca2Cl C. CaCl D. CaCl3

29. Sec.18 (b) of Art. III of RA 7920: Examination and Registration. Qualifications of
Applicants for Registered Master Electricians, states that an applicant is at least be
___ years of age.
A. 23 B. 22 C. 21 D. 18

30. Sec. 17 (b) of Art. III of RA 7920: Examination and Registration. Qualifications of
Applicants for Registered Electrical Engineers, states that an applicant is at least be
___ years of age.
A. 21 B. 23 C. 24 D. 25

31. Find MW of HNO3 in g/mole.


A. 72 B. 61 C. 73 D. 63

Solution:

𝐻 = 1𝑥1 = 1

6
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑁 = 14 𝑥 1 = 14
𝑂3 = 16 𝑥 3 = 48
1 + 14 + 48 = 𝟔𝟑
32. What is the chemical formula of Sulfuric acid?
A. HSO4 B. H2SO4 C. H3SO2 D. HSO2

33. 1KB is how many bytes?


A. 1000 B. 1024 C. 1012 D. 1048

34. What is the unit of strain?


A. Pa B. unit less C. N-m D. N-m/s

35. Which of the following is an example of an integrity violation of e-commerce


security?
A. A Website is not actually operated by the entity the customer behaves in to be
B. A merchant uses customer information in a manner not intended by the customer
C. A customer denies that he or she is the person who placed the order
D. An unauthorized person intercepts an online communication and changes
its content

36. What is the physical appearance of sodium chloride?


A. Silver metal B. White crystal C. Yellowish Gas D. White metal

37. What is the oxidation number of Cr in the dichromate ion (Cr2O2)-2 ?


A. -1 B. 0 C. 2.5 D. 6

Solution:
2𝑥 + (−14) = −2

∴𝑿 = 𝟔

38. A software that is commonly known as firmware.


A. OS B. Cache Memory C. BIOS D. IO

39. Pulverized fuel is used for


A. Better burning C. More calorific value
B. Less radiation loss D. Medium sized units

40. An unknown fuel has a mass density of 805 kg/m3. Find its specific gravity.
A. 0.805 B. 1.242 C. 1.610 D. 0.621

7
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝜌 805 𝒌𝒈
𝑆. 𝐺 = = = 𝟎. 𝟖𝟎𝟓
𝜌𝐻2𝑂 1000 𝒎𝟑

41. Which of the following is a variable renewable source of energy?


A. Hydro-power C. Biomass Energy
B. Geothermal Energy D. Solar Energy

42. Which of the following is a conventional source of energy?


A. Coal B. Solar C. Wind D. Tidal

43. In cold working of metals


A. close dimensional tolerance cannot be maintained
B. poor surface finish is obtained
C. recrystallization temperature for steel is reduced
D. strength and hardness of steel is increased

44. An object is dropped from an original height h hitting the ground with velocity v. How
much greater will speed hitting the ground be if the object is dropped from a height 4
times the original height?
A. 4 times B. 2 times C. √2 times D. 16 times

Solution:

𝑉𝑓 = 𝑉𝑜 + 2𝑔ℎ

𝑉2 = 2𝑔ℎ

𝑉22 2𝑔 ℎ
= 2𝑔2 ℎ2
𝑣12 1 1

𝑉22 8
=2=4
𝑣12

𝑉22
√ = √4
𝑣12

𝑉2
=2
𝑉1

𝑽𝟐 = 𝟐𝑽𝟏

45. An inventor clams to extract 100 kJ of energy from 30°C sea water and generate 7
kJ of heat while rejecting 93 kJ to a 10°C stratum. The scheme fails because;

8
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. The temperature of the sea water is too low C. It violates the first law
B. It is perpetual-motion machine D. It violates the second law

46. The second period contains how many elements?


A. 2 B. 4 C. 6 D.8

47. An isentropic process:


A. is adiabatic and reversible C. is adiabatic but may not be reversible
B. is reversible but may not be adiabatic D. is always reversible

48. A driver fills an 18.9 L can with gasoline at 15.0°C right up to the top. He forgets to
replace the cap and leave the can in the back of his truck. The temperature climbs to
30.0°C by 1 PM. How much gasoline spills out of the can? Assume a coefficient of
linear expansion of steel to be 12x10-5 K-1 and the coefficient of volumetric
expansion of gasoline to be 950 x 10-6 K-1.
A. 0.62 L B. 0.26 L C. 0.27 L D. 0.72 L

Solution:

49. My Johnson borrows $ 100,000 at 10% effective annual interest. He must pay back
the loam over 30 years with uniform monthly payments due on the first day of each
month. What does Mr. Johnson pay each month?
A. $839 B. $846 C. $870 D. $884

Solution:

𝑖 12
𝑖 + 1 = (1 + )
12
𝑖 12
1.10 = (1 + )
12

𝑖
= 0.007974
12

𝑇𝑜𝑡𝑎𝑙 𝑛𝑢𝑚𝑏𝑒𝑟 𝑜𝑓 𝑝𝑎𝑦𝑚𝑒𝑛𝑡𝑠 = 12(30) = 360

𝐵𝑜𝑟𝑟𝑜𝑤𝑒𝑑 𝑚𝑜𝑛𝑒𝑦 = 𝐴 + 𝑃

𝐴[(1 + 0.007974)359 − 1]
100,000 = 𝐴 +
(1 + 0.007974)359 (0.007974)

𝐴 = 839

9
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
50. Air has a specific heat of 1 kJ /kg-K. If BTU of energy is added to 100 g of air, what
is the change in air temperature?
A. 10.0°C B. 21.1°C C. 44.1°C D. 88.2°C

Solution:

𝑄 = 𝑚𝐶𝛥𝑇
𝑄 2.11
𝛥𝑇 = = (0.1)(1) = 𝟐𝟏. 𝟏°𝑪
𝑚𝐶

51. A pump has an efficiency of 65%. It is driven by a 0.75 horsepower motor. The
pump produced a pressure rise of 120 Pa in water. What is the required flow rate?
A. 3.03 m3/s B. 4.04 m3/s C. 4.55 m3/s D. 4.66 m3/s

Solution:
𝑃𝑜𝑢𝑡 = 𝜂𝑃𝑖𝑛 = (0.65)(0.75 𝑥 746 ) = 363.675 𝑊

𝑃𝑜𝑢𝑡 = 𝑄𝛾ℎ 𝑏𝑢𝑡 𝛾ℎ = 𝑃

𝑃𝑜𝑢𝑡 = 𝑄𝑃

𝑃𝑜𝑢𝑡 363.675
𝑄= = = 𝟑. 𝟎𝟑 𝒎𝟑/𝒔
𝑃 120

52. What is the tensile load if a ½” x 4” x 12” steel tie rod experience an 80°F
temperature decrease from the no stress temperature?
A. 92,346 lb B. 47,120 lb C. 31,200 lb D. 52,130 lb

Solution:
𝑁𝑜𝑡𝑒: 𝑛𝑜 𝑠𝑡𝑟𝑒𝑠𝑠 𝑑𝑢𝑒 𝑡𝑜 𝑡𝑒𝑛𝑠𝑖𝑙𝑒

𝑃
𝛼 (∆𝑇) =
𝐴𝐸

𝑃
6.5𝑥10−6 (80) = 1
( 𝑥4)(30𝑥106 )
2

𝑷 = 𝟑𝟏, 𝟐𝟎𝟎 𝒍𝒃

53. The rate of return for a ₱10,000 investment that will yield ₱ 1,000 per year for 20
years is closest to
A. 2% B. 4% C. 8% D. 16%

Solution:

10
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
(1+𝑖)𝑛 −1
𝑃 = 𝐴[ ]
𝑖(1+𝑖)𝑛

(1+𝑖)20 −1
10,000 = 1000 [ ]
𝑖(1+𝑖)20

𝑖 = 0.0775 𝑥 100% = 𝟖%

54. The overall energy program formulated and updated yearly by the DOE and
submitted to Congress pursuant to R.A. 7638.
A. Power Development Plan (PDP) C. Philippine Electrical Code (PEC)
B. Philippine Energy Plan (PEP) D. Preliminary Project Planning Data (PPPD)

55. The work of a polytrophic (n=1.21) compression of air (Cp/Cv = 1.4) in a system with
moving boundary from P1= 15 psia, V1=1.0 cu.ft. to P2=150 psia, V2=0.15 cu.ft. is.
A. 1080 ft-lb B. 5150 ft-lb C. 6882 ft-lb D. 2700 ft-lb

Solution:
𝑷 𝟐 𝑽𝟐 − 𝑷 𝟏 𝑽𝟏
𝑾=
𝟏−𝒏
𝟏𝟓𝟎(𝟏𝟒𝟒)(𝟎.𝟏𝟓)−(𝟏𝟓𝒙𝟏𝟒𝟒)(𝟏)
𝑾= 𝟏−𝟏.𝟐𝟏

𝑾 = 𝟓𝟏𝟒𝟐. 𝟖𝟔 𝒇𝒕 − 𝒍𝒃 ≈ 𝟓𝟏𝟓𝟎 𝒇𝒕 − 𝒍𝒃
56. One Newton is equivalent to
A. 105 dyne B. 106 dyne C. 107 dyne D. 108 dyne

57. An adiabatic process with no work done is


A. isometric B. throttling C. isobaric D. polytropic

58. Article IV Rule __________. Requirements form examination as a REE.


A. 14 B. 15 C. 16 D. 17

59. The phenomenon known as corrosion in metals is by nature


A. chemical B. organic C. electrochemical D. electrical

60. A force causing a rise in liquid in tubes of small diameter.


A. cohesion B. surface tension C. capillarity D. adhesion

61. Also known as PRC Renewal Law.


A. RA 8189 B. RA 8981 C. RA 7920 D. RA 184

62. A price tag of ₱1,200 is payable in 60 days but if paid within 30 days it will have a 3
percent discount. Find the rate of interest.

11
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 36.33 percent B. 36.12 percent C. 37.66 percent D. 37.11 percent

Solution:
𝐼 = 𝑃𝑖𝑛

30
(1200)(0.03) = 1200 (1 − 0.03) (𝑖) (360)

𝑰 = 𝟑𝟕. 𝟏𝟏 %

63. A projectile leaves a velocity of 50 m/s at an angle of 30 degrees with the horizontal.
Find the maximum height that it could reach.
A. 28.46 m B. 31.86 m C. 41.26 m D. 51.26 m

Solution:
2
(𝑉𝑜𝑆𝑖𝑛𝜃)
𝐻 = 2𝑔

((50)(𝑆𝑖𝑛30))2
𝐻 =
2(9.81)

𝑯 = 𝟑𝟏. 𝟖𝟔 𝒎

64. The majority of the rocks in the Earth’s crust are:


A. igneous B. metamorphic C. Sedimentary D. volcanic

65. The zone of the atmospheric in which weather occurs is known as the
A. ionosphere B. mesosphere C. troposphere D. stratosphere

66. What is another term for modulus of elasticity?


A. Bulk modulus C. Constant of elongation
B. Shear strain D. Young’s modulus

67. What do you call earth and stone mixed with the iron oxide?
A. Hematite B. Magnetite C. Grangue D. Ore

68. Which light contains wavelengths of all or nearly colors?


A. White Light B. Laser C. X-ray D.Gamma rays

69. A 10-mm diameter brass rod has a modulus of elasticity of E=100 GPa. If it is 4 m
long and subjected to an axial tensile load of 6KN, determine its elongation.
A. 3.06mm B. 3.60m C. 2.34mm D. 2.43mm

12
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝜌𝐿
𝑆 =
𝐴𝐸
(6𝑥103 )(4)
𝑆 = 𝜋 10 2
( )( ) (100𝑥109 )
4 1000

𝑺 = 𝟑. 𝟎𝟔 𝒎𝒎
70. RA 7920, Rule 2(n), defining ?
A. DECS B. Syllabi C. Board D. CHED

71. What rules are included in article V of RA 7920?


A. RULE 11 to 20 B. RULE 28 to 34 C.RULE 21 to 27 D.RULE1 to 20

72. In the case of a regenerative gas turbine engine, which of the following is false?
A. The regenerator improves the efficiency of the engine
B. The amount of energy required during combustion is less than that required in a
similar gas turbine if the power is constant.
C. The exit temperature of the regenerator is higher than the inlet temperature of the
compressor.
D. There is no heat rejected to the atmosphere in a regenerative gas turbine
engine.

73. When exposed to the atmosphere, which of the following liquids is coldest?
A. Oxygen B. Argon C. Nitrogen D. Helium

74. What is the temperature rating of a TW insulated conductor?


A. 60 deg C B. 75 deg C C. 90 deg C D. 100 deg C

75. The brain of any computer system is


A. ALU B. Memory C. CPU D.Control Unit

76. Electrical symbol represented by a solid line


A. intercom wiring B. telephone wiring C. conduit D.service entrance

77. A storage system for small amounts of data is


A. magnetic card B.magnetic tape C.Punched card D.Optical mark reader

78. The place where buyers and sellers come together


A. Market B. Business center C.Recreation center D.Buy and sell section

79. Which is most common language used in web designing ?


A. C B. C++ C. PHP D. HTML

13
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
80. Device used to pull wire through the conduit.
A. straps B. fish tape C. wire tongs D. puller

81. Which of the following elements are stored in oil to prevent explosions?
A. Lithium B. actinium C. ytterbium D.strontium

82. How long in nearest years) will it take money to quadruple if it earns 7%
compounded semi-annually?
A. 20 B. 18 C. 21 D. 19

Solution:
𝑖
𝐹 = 𝑃 (1 + 𝑚)𝑚𝑛

𝐹 = 4𝑃
0.07 4𝑛
4𝑃 = 𝑃 (1 + )
4

𝑵 = 𝟐𝟎 𝒚𝒆𝒂𝒓𝒔
83. If P5,000 shall accumulate for 10 years at 8% quarterly, then what is the copound
interest at the end of 10 years?
A. P6,080.40 B. 6,020.40 C. P6,040.20 D. P6,060.20

Solution:

𝐼 = 𝐹– 𝑃
0.08 10(4)
𝐼 = 5,000 (1 + ) − 5,000
4

𝑰 = 𝑷𝟔, 𝟎𝟒𝟎. 𝟐𝟎
84. A soild wooden cube , 30.0 cm on each edge, can be totally submerged in water if it
is pushed downward with a force of 54.0 N. what is the density of the wood?
A. 600 kg/m3 B. 700 kg/m3 C. 800 kg/m3 D. 900kg/m3

Solution:
𝛴 𝐹𝑦 = 0
𝑊 + 𝑇 – 𝐹𝑏 = 0
𝑊 + 𝑇 = 𝐹𝑏
𝑤 = 𝑚𝑔 , 𝐹𝑏 = ᵧ 𝑉𝑑
𝑚 (9.81) + 54 = 9.81 𝑥 103(0.3)3
𝑚 = 21.495 𝑘𝑔

14
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑚
𝜌=
𝑣
21.495
𝜌=
(0.3)3
𝒌𝒈
𝝆 = 𝟕𝟗𝟔. 𝟏𝟑
𝒎𝟑
85. An ideal gas has a volume of exactly 1 liter at 1. 00 atm and -20 degree C. To how
many atmosphers pressure must it be subjected to be compressed to 0.500 liter
when the temperature is 40 degree C?
A. 2.47 atm B. 2.74 atm C. 3,92 atm D. 2.39 atm

Solution:
𝑷 𝟏 𝑽𝟏 𝑷 𝟐 𝑽𝟐
=
𝑻𝟏 𝑻𝟐
(𝟏)(𝟏) 𝟐𝑷 (𝟎.𝟓)
(−𝟐𝟎+𝟐𝟕𝟑)
= (𝟒𝟎+𝟐𝟕𝟑)

∴ 𝑷𝟐 = 𝟐𝟕𝟎𝟎 𝒇𝒕 − 𝒍𝒃

86. For dwelling unit, the demand factor for the first 3000 volt-amperes of load is
A. 95% B. 85% C. 100% D. 80%

87. Gold with 79 protons has an atomic number of


A. 52 B. 57 C. 67 D. 79

88. An Electrical Engineer shall give ______to the engineering work of the person to
whom the credit is legally due.
A. loyalty B. advise C. honor D. credit

89. An establishment or a system for the production and modification of electric energy is
an _______.
A. Electric supply B. Electric system C. Substation D.Electric plant

90. Which element melts in your hand like chocolate bar?


A. krypton B. tantalum C. strontium D. cesium

91. BCD is
A. Binary Coded Decimal B. Bit Coded Decimal
C. Binary coded digit D. Bit Coded Digit

92. Which of the following is Charle's Law?


A. V=k x 1/P B. P1/T1=P2/T2 C. PV=mRT D. V/T=k

15
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
JULY 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

93. EPIRA is RA _____.


A. 184 B. 9136 C. 9163 D. 7920

94. Installations underground or in concrete slabs or masonry in direct contact with the
earth.
A. wet location B. dry location C.damp location D.moist location

95. The continuity equation is an expression of


A. conservation of mass C. conservation of momentum
B. conservation of energy D.conservationof angular momentum

96. If you place your hand underneath, but not touching , a kettle of hot water, you
mainly feel the presence of heat from
A. conducting B. convection C. radiation D.all of these

97. a ball is thrown straight up into air,. Ignore air resistance. While the ball is in the air
its acceleration
A. Increases B. is zero C. remains constant D. decreases

98. When a vapor condenses to a liquid,


A. its internal energy increases
B. its temperature rises
C. its temperature falls
D. it gives off internal energy

99. What is true about the polytropic exponent, for a perfect gas undergoing an isobaric
process?
A. n > 0 B. n < 0 C. n --> D. n = 0

100. In molecules of the same composition, what are the variations of atomic
arrangements known as?
A. polymers B.monomers C. isomers D.crystal systems

16
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM MARCH 2018

1. Maximum distance for support for rigid metallic conduits


A. 2000 mm B. 2500 mm C. 3000 mm D. 3500 mm

2. What is the factor (A/P, 1%,n)?


A. Uniform series present worth factor C. sinking fund factor
B. Uniform series compound factor D. Capital recovery factor

3. A process in which pressure is constant.


A. Isobaric B. Isochoric C. Isometric D. Isothermal

4. The present worth of all depreciation over the economic life of the item is called
A. Maintenance C. depreciation recovery
B. capital recovery D. annuity

5. Using an allowable shearing stress of 30 MPa, design a solid steel shaft to transmit
9kw at speed of 1200 rpm.
A. 32 mm B. 23 mm C. 46mm D. 64 mm

Solution:
2πNT
P= 60

2π(1200)(T)
9000 = 60

T= 71.62 N-m
16T
𝑇𝑠 = πD³

16(71.62)
30000000 = = , 𝑫 = 𝟐𝟑𝒎𝒎
πD3

6. EPIRA Is RA________________.
A. 184 B. 9136 C.9163 D.7920

7. The number 1010 base 2 is equivalent to decimal number_______.


A. 6 B. 10 C. 8 D. 12

Solution:

𝟏 𝟎 𝟏 𝟎
↓ ↓ ↓ ↓

17
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝟖 𝟒 𝟐 𝟏
∴ 8 + 2 = 𝟏𝟎

What is the value of 11101110 base 2 to base 8?


A. 356 B. 365 C. 653 D. 635

Solution:

Group by 3 numbers starting to right side

11 / 101 / 110

21 / 421 / 421 =

2+1=3 4+1 = 5 4+2 =6

Therefore 356

8. An asset is purchased for P 120,000,00. Its estimated life is 10 years, after which it
will be sold for P 12,000,00. Find the depreciation for the second year using SOYD
method.
A. P 17,673 B. 17,637 C. P 18,236 D.18, 326

Solution:
𝑅𝑒𝑣𝑒𝑟𝑠𝑒 𝐷𝑖𝑔𝑖𝑡𝑠
𝑑𝑒𝑝𝑟𝑒𝑐𝑖𝑎𝑡𝑖𝑜𝑛 = 𝐹𝐶 − 𝑆𝑉 ( )
𝑆𝑢𝑚 𝑜𝑓 𝑡ℎ𝑒 𝐷𝑖𝑔𝑖𝑡𝑠

10 − 2 + 1
𝑑𝑒𝑝𝑟𝑒𝑐𝑖𝑎𝑡𝑜𝑛 = 120000 – 12000 ( )
55

𝒅𝒆𝒑𝒓𝒆𝒄𝒊𝒂𝒕𝒊𝒐𝒏 = 𝟏𝟕𝟔𝟕𝟐. 𝟕𝟑 = 𝟏𝟕𝟔𝟕𝟑

9. A student will receive P 3,000 at the beginning of each 3 months for 4 years. What is
the sum of this annuity of the end of the 4th year if the interest rate is 6%
compounded quarterly?

A. P 45,604 B. P 54,604 C. P 64.620 D. P 46, 690

Solution:

0.06 𝑥
∑16
1 3000 (1 + ) = 𝟓𝟒𝟔𝟎𝟒
4

18
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
11. A wire or cable carrying current, supported by poles, tower and other structure, but
not including vertical or lateral connecting wires.
A. Transmission line B. Line conductor C. Conductor D. Lateral conductor

12. According to RA. 7920 the members of the BSEE shall hold office for a term of
_______ years from the date of appointment or until their successors shall have
been appointed and qualified.
A. 6 B. 4 C.3 D. 5

13. A equipment cost P10,000 with a salvage value of P500 at the end of 10 years.
Calculate the annual depreciation cost by sinking fund method at 4% interest.
A. 791.26 B. 729.28 C. 854.62 D. 896.48

Solution:

(𝐶𝑜−𝑆𝑉)(𝑖)
d=
(1+𝑖)2 −1

(10000−500).04)
𝑑=
(1+.04)2 −1

𝐝 = 𝟕𝟗𝟏. 𝟐𝟔

14. When a part is constrained to move when heated, ot develops


A. Principal stress B. Tensile stress C. Compressive stress D. Shear stress

15. Newton's first law is often referred to as which of the following?


A. The law of straight-line motion C. The law of inertia
B. The law of momentum D. F = ma

16. The object that has momentum must also have


A. Acceleration B. Impulse C. Kinetic Energy D. Potential Energy

17. The maximum strain energy stored in a body without permanent deformation is
known as
A. Impact energy C. Resilience
B. Proof resilience D. Modulus of Resilience

18. A surveyors steel tape with a cross sectional area of 2.5 sq. mm must be stretched
with a pull of 70 N when n use. If the modulus of elasticity of the steel is 207 GPa.
What is the elongation in the 30 m tape?

19
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 4.06 mm B. 6.40 mm C. 3.02 mm D. 2.30 mm
Solution:

PL
ȣ=
𝐴𝐸

(70)(30)
ȣ=
(2.5)(1/1000)2(207x109)

ȣ = 4.06 mm

19. The phenomenon of melting under pressure and freezing again when the pressure is
reduced is known as
A. Sublimation B. Condensation C. Deposition D. Regelation

20. Falling drops of water become spherical due to


A. Capellarity B. Viscosity C. Surface tension D. Compressibility

21. A tank contains oil sp. gr = 0.80, gasoline sp. gr = 0.90 and seawater sp. gr = 1.03. If
the depths of the liquids are 0.5m, 0.8m, and 1m for oil, gasoline and sea water,
respectively. Find the pressure at a depth of 1.8m.
A. 21.092 kPa C. 16.04 kPa
B. 10.104 kPa D. 18.86 kPa

Solution:

P = pgh
𝑃 = 0.8(998)(0.5)(9.8) + 0.9(998)(0.8)(9.8) + 1.03(998)(0.5)(9.8)
𝑷 = 𝟏𝟔. 𝟎𝟒 𝒌𝑷𝒂

22. A pressure gage measure 50 kPa vacuum in a system. What is the absolute
pressure, if the atmospheric pressure is 101 kPa?
A. 51,000 C. 53,000
B. 52,000 D. 55,000

Solution:

𝑃𝑎𝑏𝑠 = 𝑃𝑎𝑡𝑚 − 𝑃𝑣𝑎𝑐𝑢𝑢𝑚


= 101𝑘𝑃𝑎 − 50𝑘𝑃𝑎
= 𝟓𝟏, 𝟎𝟎𝟎 𝑷𝒂

23. Which of the following engines is less efficient?


A. gas turbine B. diesel engine C. Carnot engine D. gasoline engine

20
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

24. A steel rod of circular cross-section is to carry a tensile load of 30,000 lbs. The
allowable working stress in shear for the rod is 8,000 psi. Find the required diameter
for the rod.
A. 1.093 in C. 2.185 in
B. 3.09 in D. 1.545 in

Solution:
𝑷
𝝈=
𝑨
30000
=𝜋
(𝑑 2 )
4
𝒅 = 𝟐. 𝟏𝟖𝟓 𝒊𝒏

25. A bar under tension is called a


A. strut B. beam C. shaft D. tie

26. A man paid a 10% down payment of P2,000,000 for a house and lot and agreed to
pay the balance on monthly installments for 5 years at an interests rate of 15%
compounded monthly. What is the monthly installment in pesos?
A. 44,528.34 B. 42,821.87 C. 43,625.92 D. 45,365.78

Solution:

𝑃 = 2,000,000 − 200,000

A[(1 + i)n − 1]
P=
(1 + 𝑖)𝑛 − 1
0.15 5(12)
A [(1 + 12 ) − 1]
1,800,000 =
0.15 5(12) 0.15
(1 + 12 ) ( 12 )
𝑨 = 𝟒𝟐, 𝟖𝟐𝟏. 𝟖𝟕

27. Conductors from the service point to the service disconnecting means
A. Feeder B. Service Lateral C. Service Conductor D. Branch Circuit

28. A market situation where there are few sellers and few buyers
A. oligopoly C. bilateral oligopoly
B. oligopsony D. bilateral oligopsony

21
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
29. When a sound wave goes from air to water, the quantity that remains unchanged is
it’s
A. speed B. amplitude C. frequency D. wavelength

30. The index of refraction of benzene is 1.5. The speed of light in benzene is
A. 1.5 x 10^8 m/s B. 2 x 10^8 m/s C. 3 x 10^8 m/s D. 4.5 x 10^8 m/s

Solution:
𝑐
𝑣=
𝑛
3𝑥108
=
1.5
𝒗 = 𝟐𝒙𝟏𝟎𝟖 𝒎/𝒔

31. In how many years will P100 000earned as compound interest of P50 000 if the
interest rate is 9% compounded quarterly?
A. 3.5 B. 4.5 C. 5.56 D. 2.11

Solution:
50000 = 100000 (1 + (0.09)(𝑁))
∴ 𝟒. 𝟓𝟓

32. A fluid said to be ideal if it is


A. incompressible C. viscous and incompressible
B. inviscous D. inviscous and incompressible

33. The current in ampere that the conductor can carry continuously under the
conductor of use without exceeding its temperature rating.
A. Maximum current C. Ampacity
B. Continous current D. Rated Current

34. A farmer selling eggs 50 pesos a dozen gain 20%. If he sell the eggs at the same
price after the cost of the eggs by 12.5%. How much his new gain in percent?
A. 6.89 B. 6.67 C. 6.58 D. 6.12

Solution:

50 = 𝑋 𝑥 0.20 = 250
250 𝑥 0.125 = 31
(50 −31)
= 𝟔. 𝟏𝟐
31

35. A loan of P5000 is made for a period of 15 months, at a simple interest of 15%, what
future amount is due at the end of the loan period?
A. P5937.5 B. P5870.3 C. P5712.40 D. P5690.12

22
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

𝐹 = 𝑃(1 + 𝑛𝑖)
15
𝐹 = 5000(1 + (12)(0.15)
𝑭 = 𝟓𝟗𝟑𝟕. 𝟓

36. Mr. Bacani borrowed money from the bank. He received from the bank P1842 and
promise to repay P2000 at the end of 10mos, determine the rate of simple interest.
A. 12.19% B. 12.03% C. 11.54% D. 10.29

Solution:

𝐹 = 𝑃(1 + 𝑛𝑖)
10
2000 = 1842(1 + (12)(𝑖)
𝑰 = 𝟏𝟎. 𝟐𝟗

37. What rate of interest compound annually is the same as the rate of interest of 8%
compounded quarterly?
A. 8.07% B. 8.12% C. 8.16% D. 8.24%

Solution:
𝑟 0.06 4
(1 + 2) 2 − 1 = (1 + ) −1
4
∴ 𝟖. 𝟐𝟒%

38. The second period contains how many elements?


A. 2 B. 4 C. 6 D. 8

39. Mercury carnot wet a glass tube, this due to


A. cohesion B. Adhesion C. Surface tension D. viscosity

40. An amount of P1000 becomes P1608.44 after 4years compounded bimonthly. Find
the nominal rate.
A. 11.69% B. 12.00% C. 12.08% D. 12.32

Solution:
4
1608.44 = 1000 (1 + (𝑟/(60))0.91
∴ 𝟏𝟏. 𝟖𝟗%

41. What is the shortcut key to reach the end of the document?
A. End B. Ctrl + End C. Shift + End D. Home

23
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

42. What refers to a system in which there is flow of mass across its boundaries?
A. Open system B. Closed system
C. Isolated system D. Steady flow system

43. A rubber ball is dropped from a height of 2 m. if there is no loss of velocity after
rebounding, the ball will rise to a height of
A. 2 m B. 1 m C. 3 m D. 4 m

44. Device that takes data from user and convert it into form that can be easily
understandable by computer is
A. storage device B. output device
C. input device D. pointing device

45. How long will it take money to double itself if invested at 5% compounded annually?
A. 13.7 years B. 14.7 years C. 14.2 years D.15.3 years

Solution:

𝐹 = 𝑃(1 + 𝑖)𝑛
𝑇𝑜 𝑑𝑜𝑢𝑏𝑙𝑒 𝑡ℎ𝑒 𝑚𝑜𝑛𝑒𝑦, 𝐹 = 2𝑃
2𝑃 = 𝑃 (1 + 𝑖)𝑛
2 = (1 + 0.05)𝑛
𝑇𝑎𝑘𝑒 𝑙𝑜𝑔 𝑜𝑛 𝑏𝑜𝑡ℎ 𝑠𝑖𝑑𝑒𝑠
log 2 = 𝑛 log 1.05
log 2
𝑛 = log 1.05
𝒏 = 𝟏𝟒. 𝟐 𝒚𝒆𝒂𝒓𝒔

46. If a computer in a network accesses resources that are shared by other computers it
is called a
A. server B. client C. receiver D. sender

47. What annuity is required over 12 years to equate with a future amount of P20, 000?
Assume i = 6% annually
A. P1, 290.34 B. P1, 185.54
C. P1, 107.34 D. P1, 205.74

Solution:

(𝟏+𝒊)𝒏 −𝟏
𝐹=𝐴 [ ]
𝒊
(1+0.06)12 −1
20,000 = 𝐴 [ ]
0.06
𝑨 = 𝑷𝟏, 𝟏𝟖𝟓. 𝟓𝟒

24
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
48. A baseball is thrown in a horizontal plane following a parabolic path with an initial
velocity of 100 m/s at an angle 30° above horizontal. Solve the distance from the
throwing point that the ball attains its original level.
A. 890 m B. 883 m C. 858 m D. 820 m

Solution:
2𝑉 sin 𝜃
𝑅 = (cos 𝜃) ( )
𝑔
2(100)(sin 30)
= (cos 30) ( ) = 𝟖𝟖𝟐. 𝟕 𝒐𝒓 𝟖𝟖𝟑 𝒎
𝟗.𝟖𝟏

49. The property of a fluid which enables it to resist tensile stress is known as
A. compressibility B. surface tension
C. cohesion D. adhesion

50. The ratio of the lateral strain to the linear strains is


A. modulus elasticity B. modulus of rigidity
C. bulk modulus D. Poisson’s ratio

51. A uniform series payment occurring at equal interval of time is called


A. Annuity B. Amortization C. Depreciation D. Bond

52. A train whose speed is 60 mph rounds a curve whose radius of curvature is 484 ft.
What is its acceleration?
A. 12 ft/sec 2 B. 𝟏𝟔 𝐟𝐭/𝐬𝐞𝐜 𝟐 C. 14 ft/sec 2 D. 10 ft/sec 2

Solution:
1.61 𝑘𝑚 1000 𝑚 3.28 𝑓𝑡 1 ℎ𝑜𝑢𝑟 𝑓𝑡
𝑣 = 60 𝑚𝑖𝑙𝑒𝑠⁄ℎ𝑜𝑢𝑟 × 1 𝑚 × 1 𝑘𝑚 × 1 𝑚 × 3600 𝑠𝑒𝑐𝑠 = 88.013 ⁄𝑠𝑒𝑐
𝑓𝑡 2
2 (88.013 ) 𝒇𝒕
𝑎 = 𝑣 ⁄𝑟 = 𝑠𝑒𝑐 ⁄
484 𝑓𝑡 = 1𝟔 ⁄𝒔𝒆𝒄𝟐

53. The process of diffusion into the other through a semi-permeable membrane is
called
A. viscosity B. osmosis C. surface tension D. diffusivity

54. What refers to the need, want or desire for a product backed by the money to
purchase it?
A. Supply B. Demand C. Product D. Good

55. Is the worth of property as shown in the accounting records


A. Scrap Value B. Book Value C. Fair Value D. Use Value

56. How much should you put into a 7.9% savings account in order to have $175,000 in
63 years?
A. $1,541.55 B. $1,454.41 C. $1,342.21 D. $1,356.32
25
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:
𝐹 175,000
𝑃= = (1+0.079)63 = $𝟏, 𝟒𝟓𝟒. 𝟒𝟏
(1+𝑖)𝑛

57. The branch of mechanics that deals with bodies in motions is known as
A. statics B. dynamics C. kinetics D. kinematics

58. An escalator raises a 100 kg bucket of sand in 10 m in 1 minute. Determine the total
amount of work done during the process.
A. 9800 J B. 32200 J C. 102 J D. 98 J

Solution:

1𝑘𝑔 = 9.81 𝑁𝑒𝑤𝑡𝑜𝑛


100 𝑘𝑔 × 9.8 𝑁 × 10 𝑚 = 𝟗𝟖𝟎𝟎 𝑱

59. The energy absorbed in a body, when it is strained within the elastic limits, is known
as
A. Strain energy B. Resilience C. Proof resilience D. Modulus of resilience

60. A side (2 in.) of a square bar is loaded in tension by a force of 12 kips. Determine
the normal stress in ksi in the square bar.
A. 5.5 B. 6 C. 2.6 D. 3

Solution:

𝑏 = 2 𝑖𝑛
𝐹 = 12 𝑘𝑖𝑝𝑠
𝐹 12
𝑆 = 𝐴 = 2×2 = 𝟑 𝒌𝒔𝒊

61. The simple mathematical statement of the relationship between elastic stress and
strain stress is proportional to strain. What is this law?
A. Boyle′ s law B. 𝐇𝐨𝐨𝐤𝐞′ 𝐬 𝐥𝐚𝐰 C. Charles′ s law D. Gas law

62. The first law of Thermodynamics is based on which of the following principles?
A. Conservation of mass
B. 𝐂𝐨𝐧𝐬𝐞𝐫𝐯𝐚𝐭𝐢𝐨𝐧 𝐨𝐟 𝐞𝐧𝐞𝐫𝐠𝐲
C. Action and reaction
D.The entropy − temperature relationship

63. Stationary waves are also called


A. static waves C. progressive waves
B. 𝐬𝐭𝐚𝐧𝐝𝐢𝐧𝐠 𝐰𝐚𝐯𝐞𝐬 D.all of these

26
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

64. Top of window which displays program’s name consist of


A. menu bar B. thumbnail C. dialog box D. title bar

65. A quantity of gas occupies 1.2 cu. Ft. at STP. The gas is allowed to expand to 1.5
cu. Ft. and at 15 psia. What is the new temperature?
A. 700 deg R B. 627.6 deg R C. 640 deg R D. 590 deg R

Solution:

𝑃1 𝑉1 𝑃2 𝑉2
=
𝑇1 𝑇2
@ 𝑆𝑇𝑃
𝑇 = 0℃ = 32℉ = 492°𝑅
𝑃 = 1 𝑎𝑡𝑚 = 14.7 𝑝𝑠𝑖

14.7 𝑝𝑠𝑖 15 𝑝𝑠𝑖 (1.5𝑓𝑡 3 )


=
492°𝑅 𝑇2
𝑻𝟐 = 𝟔𝟐𝟕. 𝟔 °𝑹

66. What is force per unit area?


A. work B. energy C. 𝐩𝐫𝐞𝐬𝐬𝐮𝐫𝐞 D. power

67. In a hydraulic press, the small cylinder has a diameter of 8 cm, while the larger
piston has a diameter of 22 cm. If a force of 600 N is applied t the small piston, what
is the force on the larger piston neglecting friction?
A. 3.5 kN B. 4.5 kN C. 5.5 kN D. 6.6 Kn

Solution:
𝐹
Ρ=
𝐴
𝜋𝒹 2
A=
4
𝑃𝑆 = 𝑃𝐿
𝐹𝑆 𝐹
= 𝐴𝐿
𝐴𝑆 𝐿

600 𝑁 𝐹𝐿
𝜋 = 𝜋
(80 ∗ 80) (22 ∗ 22)
4 4

𝐹𝐿 = 𝟒. 𝟓𝐤𝐍

68. Which of the following metallic element has a meaning “heavy stone”?
A. Titanium B. Iron C. Cobalt D. Tungsten

27
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

69. Formula for Calcium chloride.


A. CaCl2 B. Ca2Cl C. CaCl D. CaCl3

70. What is the principle behind fiber optics?


A. Reflection B. Refraction C. Diffraction D. Dispersion

71. When work done in moving a particle round a closed loop in a field is zero, forces in
field are called
A. Zero forces B. Non-conservative forces
C. Conservative forces D. Viscous forces

72. What is the critical angle, in degree, of the incidence for a ray of light passing from
the glass into water? Assume index of refraction for glass = 1.54 and index of
refraction of water = 1.33
A. 59.7 B. 45.8 C. 67.4 D. 50.9

Solution:
𝑛𝑔𝑙𝑎𝑠𝑠 sin 𝜃𝑔𝑙𝑎𝑠𝑠 = 𝑛𝑤𝑎𝑡𝑒𝑟 sin 𝜃𝑤𝑎𝑡𝑒𝑟
𝑡𝑜 𝑠𝑜𝑙𝑣𝑒 𝑓𝑜𝑟 𝑡ℎ𝑒 𝑐𝑟𝑖𝑡𝑖𝑐𝑎𝑙 𝑎𝑛𝑔𝑙𝑒 ( 𝜃𝑔𝑙𝑎𝑠𝑠 → 𝜃𝑐𝑟𝑖𝑡𝑖𝑐𝑎𝑙 )𝑡ℎ𝑒𝑛; 𝜃𝑤𝑎𝑡𝑒𝑟 = 90°
𝑛𝑤𝑎𝑡𝑒𝑟
sin 𝜃𝑐𝑟𝑖𝑡𝑖𝑐𝑎𝑙 = (sin 𝜃𝑤𝑎𝑡𝑒𝑟 )
𝑛𝑔𝑙𝑎𝑠𝑠
1.33
sin 𝜃𝑐𝑟𝑖𝑡𝑖𝑐𝑎𝑙 = (sin 90)
1.54
𝜽𝒄𝒓𝒊𝒕𝒊𝒄𝒂𝒍 = 𝟓𝟗. 𝟕 °

73. How much oxygen is required to convert 11.24 g of cadmium to 12.84 g cadmium
oxide?
A. 1.06 g B. 1.60 g C. 42.06 g D. 24.08 g

Solution:

12.84 𝑔 𝐶𝑑𝑂
−11.24 𝑔 𝐶𝑑
∴ 𝟏. 𝟔𝟎 𝒈 𝑶

74. An archer aims his bow upwards and pulls the string of his arrow with a force of 80N.
The strings make an angle of 25 degrees with vertical. Find the tension in the string
A. 88 N B. 44 N C. 22 N D. 33 N

Solution:
2 (𝑇) cos 𝜃 = 𝑇1
2 (𝑇) cos 25 = 80 𝑁
𝑻 = 𝟒𝟒. 𝟏𝟑 ≅ 𝟒𝟒 𝑵

28
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
75. Which of the following is used in thermal power plant?
A. Brayton Cycle B. Reversed Carnot Cycle
C. Rankine Cycle D. Otto Cycle

76. It requires Q of the heat to make a cup of coffee. How much energy is needed to
make 3 cups of coffee?
A. 3 Q B. 2 Q C. Q D. 4 Q

77. For shear stress, What is the constant of proportionality?


A. Shark Modulus B. Shape Modulus C. Shear Modulus D. Shout Modulus

78. While Young’s Modulus ‘E’ relates to change in length and bulk modulus ‘K’ relates
to change in volume modulus of rigidity ‘G’ relates to change in
A. Weight B. density C. shape D. temperature

79. What do you call a framework composed of members joined at their ends to form a
rigid structure?
A. Machine B. Truss C. Joist D. Purlin

80. If a 1/3 hp pump runs for 20 minutes, What is the energy used?
A. 0.06 ergs B. 0.25KN C. 0.30 MJ D. 0.11 kWhr

Solution:
1
𝐺𝑖𝑣𝑒𝑛: 𝑃 = 𝐻𝑃 , 𝑡 = 20 𝑚𝑖𝑛𝑢𝑡𝑒𝑠
3
1 746 𝑤𝑎𝑡𝑡𝑠 60 𝑠𝑒𝑐
𝑊 = 𝑃𝑡 = ( 𝐻𝑝 𝑥 ) (20 min 𝑥 )
3 1 ℎ𝑝 1 𝑚𝑖𝑛
𝑾 = 𝟎. 𝟐𝟗𝟖𝟑 𝑴𝑱 ≅ 𝟎. 𝟑𝟎 𝑴𝑱

81. Car travelled 20 m/s south in 3 min, 25 m/s east in 2 min and 30 m/s northeast in 1
min. Find the average speed in 6 min.
A. 15.31 m/s B. 13.51 m/s C. 32.33 m/s D. 23.33 m/s

Solution:

distance travelled
Average speed =
time elapsed
(20)(3)(60) + (25)(2)(60) + (30)(1)(60)
Average speed = = 𝟐𝟑. 𝟑𝟑 𝐦/𝐬
(6)(60)

82. Car travelled 20 m/s south in 3 min, 25 m/s east in 2 min and 30 m/s northeast in 1
min. Find the average velocity in 6 min.
A. 15.31 m/s B. 13.51 m/s C. 32.33 m/s D. 23.33 m/s

29
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

displacement
Average velocity =
time elapsed
√(3600 − 1800cos45)2 + (3000 + 1800cos45)2
Average speed = = 𝟏𝟑. 𝟓𝟏 𝐦/𝐬
(6)(60)

83. It is the sum of the internal energy and PV.


A. entropy B. enthalpy C. energy D. Electric field

84. Two sky divers jump at the same time and want to play catch. Where should one
aim if he wants the other to catch it?
A. below
B. above because balls falls faster
C. Above because ball falls slower
D. Straight because there’s no air resistance

85. The temperature when water vapour of the air begins to condense.
A. boiling point B. Freezing point C. Critical point D.dew point

86. What is the temperature rating of THHN Insulation?


A. 60 deg C B. 90 deg C C. 85 deg C D. 75 deg C

87. An aluminum tube (G=28 GPa) has an outer diameter of 100 mm and an inner
diameter of 50 mm. When twisted by a torque T, the tube develops a maximum
shearing strain of 650 x 10^-6. What is the magnitude of the applied torque T?
A. 4250 N-m B. 4900 N-m C. 3350 N-m D. 3800 N-m

Solution:

16 𝑇𝐷
𝜏= (𝐷 4 −𝑑4 )𝜋
𝛾
𝜀= ; 𝛾 = (6.50 𝑥10−6 )(28 𝑥109 ) = 18. 2 𝑀𝑃𝑎
𝐺

100
16 𝑇 (1000)
18. 2 𝑀𝑃𝑎 =
100 4 50 4
𝜋 (1000) − (1000)

∴ 𝑻 = 𝟑𝟑𝟓𝟎 𝑵 − 𝒎

30
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
88. Which of the following is spreadsheet software?
A. Microsoft word B. Notepad C. Microsoft excel D. PowerPoint

89. ________ is a way of writing the operating code so they may be easily translated
into machine code or direct computer instruction.
A. basic language B. Fortran C. Pascal D. Assembly language

90. In a manometer, the pressure is measured by balancing it by


A. spring weight
B. Dead weight
C. Column of liquid
D. Leverage pressure

91. A square steel bar is 2 inches on a side and 10 inches long. It is loaded by an axial
tensile force of 40,000 lb. If E = 30 x 10 6 psi and µ= 0.3, determine the change of
volume per unit volume.
A. 0.000133 B. 0.00133 C. 0.000122 D. 0.00122

Solution:
𝚫𝑽 𝑷
= (𝟏 − 𝟐𝝁)
𝐕 𝑨𝑬

𝚫𝑽 40,000
= (1 − 2(0.3))
𝐕 22 (30𝑥106 )

𝚫𝑽
∴ = 𝟎. 𝟎𝟎𝟎𝟏𝟑𝟑
𝐕

92. A solid cube of aluminum is 2.00 cm on each edge. The density of aluminum is 2700
kg/cu. m. Find the mass of the cube.
A. 26.1 g B. 21.5 g C. 32.4 g D. 34.2 g

Solution:
𝑚
ρ= ; Vcube = 0.023 = 8 x 10-6 m3
𝑣

𝑘𝑔
m = ρv = (2700 𝑐𝑢.𝑚. ) (8 x 10-6 m3) = 0.0216 kg (1000g/kg) = 21.5 g

93. Which of the follow impurity in cast iron makes it hard and brittle?
A. Silicon B. Sulfur C. Manganese D. Phosphorus

94. The property of a material by virtue of which it can be beaten or rated into plates is
called

31
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2018
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Malleability B. Ductility C. Plasticity D. Elasticity

95. The temperature of a body is 50 deg F. Find the temperarture in K


A. 10 B. 263 C. 283 D. 510

Solution:
5 5
˚C = 9 (F -32) = 9 (50 – 32) = 10 ˚C

K = ˚C + 273 = 263 K

96. The coefficient of static friction for steel on ice is 0.1. The force needed to set 70-kg
skater in motion is
A. 0.1 N B. 0.7 N C. 7 N D. 70 N

Solution:

F = µW = (0.1) (70kg) = 7 N

97. What is the term used to describe the moving of software from another computer to
your own computer?
A. Surfing B. Downloading C. Uploading D. Accessing

98. At what point is the applied force minimal in opening hinge door?
A. near the hinge B. farthest the hinge C. at the center D. anywhere

99. The colour of stars depend on


A. distance B. temperature C. atmospheric pressure D. pollutants of air

100. Which device is used to measure the wavelength of X-rays?


A. Framing square C. Manometer
B. Spectrometer D. SWR meter

32
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM AUGUST 2017

1. The thermodynamics statement of the conservation of energy of a system is the


A. first law B. second law C. third law D. zeroth law

2. For REE board examination, the passing general average is _____ provided there is
no grade below _____ in any of the subjects.
A. 75 percent, 50 percent C. 70 percent, 50 percent
B. 75 percent, 60 percent D. 70 percent, 60 percent

3. Sec. 23 of Art III of RA 7920 Issuance of Certificate of Registration. The professional


is required to renew license every _____ years upon payment of registration fees.
A. 1 B. 2 C. 3 D. 4

4. Find the amount of P30,000 at 6 percent simple interest after 5 years.

Solution:

𝐹 = 𝑃 (1 + 𝑖𝑛)

𝐹 = 30,000[1 + 0.06(5)] = 𝟑𝟗, 𝟎𝟎𝟎

5. What is the shortcut key to reach the end of the document?


A. End B. Ctrl+End C. Shift+End D.Home

6. According to RA 7920 the members of the BEE shall hold office for a term of ____
years from the date of appointment or until their successors shall have been
appointed or qualified.
A. 6 B. 4 C. 3 D. 5

7. What refers to a system in which there is flow of mass across its boundaries?
A. Open System C. Isolated system
B. Closed system D. Steady flow system

8. BIOS stands for


A. Basic Input Output Society C. Base Input Output Society
B. Basic Input Output System D. Base Input Output System

9. An investment of $350,000 is made to be allowed by payments of $200,000 each


year for three years. What is the annual rate of return on investment for this
payment?

Solution:
1−(1+𝑖)−𝑛
𝑃 = 𝐴( )
𝑖

33
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
1−(1+𝑖)−3
350,000 = 200,000 ( )
𝑖

𝒊 = 𝟑𝟐. 𝟕 %
10. What device is used to measure fluid velocity as well the velocity of fluid inside a
pipe?
A. Barometer B. Hydrometer C. Pilot tube D. Pilot tube

11. Bernouli’s equation is an expression of


A. conversation of mass C. conservation of momentum
B. conversation of energy D. conservation of mass and energy

12. Motors must be labelled with the following nameplate rating, manufacturer’s name
and etc. This is:
A. manufacturing rule C. wiring design rule
B. construction rule D. Installation rule

13. A bar of uniform cross section is subject to uniaxial tension and develops a strain in
the direction of the force 1/800. Calculate the change of volume per unit volume.
Assume u = 1/3.

Solution:
≜𝑉 𝑃 𝑃
= ( 1 − 2𝑢) ; 𝐴 = 𝑆
𝑣 𝐴𝐸
≜𝑉 1 1
= 800 (1 − 2 (3))
𝑣
≜𝑽 𝟏
= 𝟐𝟒𝟎𝟎 𝑻𝒆𝒏𝒔𝒊𝒐𝒏 𝑫𝒆𝒄𝒓𝒆𝒂𝒔𝒊𝒏𝒈
𝒗

14. Partially protected locations under canopies, marquees, roofed open porches, and
like locations, and interior locations subject to moderate degrees of moisture.
A. Wet location B. Dry location C. Damp location D. Moist location

15. What is the minimum age for a person to become a member of the Board of
Electrical Engineering?
A. 30 B. 35 C. 40 D. 45

16. The president of an engineering firm wishes to give each of his 50 employees a
holiday bonus of P10,000. How much should he invest monthly for a year at 12
percent nominal interest rate to be able to give that bonus?

Solution:
1−(1+𝑖)−𝑛
𝑃 = 𝐴( ) (1 + 𝑖)−𝑚
𝑖
0.12 −12
1−(1+ ) 0.12 −12
12
50(10000) = 𝐴 ( 0.12 )(1 + )
12
12

34
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑨 = 𝟑𝟗, 𝟒𝟐𝟒. 𝟑𝟗
17. When an object exerts a force on another object, the second object exerts on the
first a force of the same magnitude but in the opposite direction. This law is known
as:
A. Newton’s First law of Motion C. Equipment Grounding Conductor
B. Newton’s Second law of Motion D. Grounding Electrode Conductor

18. A system or circuit conductor that is intentionally grounded.


A. Grounded Conductor C. Equipment Grounding Conductor
B. Grounding Conductor D. Grounding Electrode Conductor

19. Fastest internet connection for home users nowadays.


A. DSL B. Dial-up C. FTTH D. Broadband wireless

20. Which of these elements has the highest atomic numbers?


A. Titanium B. Uranium C. Radium D. Plutonium

21. Concurrent forces are those forces whose line of action


A. meet at one point C. meet on the same plane
B. lie on the same line D. none of these

22. A couple produces


A. combined translator and rotational motion C. translator motion
B. rotational motion D. none of these

23. The rate of doing work is known as


A. Power B. potential energy C. kinetic energy D. none of these

24. A rubber ball is dropped from a height of 2m. If there is no loss of velocity after
rebounding, the ball will rise to a height of

Solution:
Velocity = Constant
ℎ0 = ℎ𝑓

∴ 𝟐𝒎

25. The condition of equilibrium or motion of a rigid body remains unchanged if a force
acting at a given point of the rigid body is replaced by a force of same magnitude
and direction, but acting at a different point provided that the two force have same
line of action. This statement is known as _____________.

35
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. PappusProspositions C. Parallelogram Law
B. Principle of Transmissibility D. Varignon’s Theorem

26. A baseball is thrown in horizontal plane following a parabolic path with an initial
velocity of 100 m/s at an angle 30 deg. above horizontal. Solve the distance from the
throwing point that the ball attains its original level.

Solution:
𝑚
𝑉𝑜 = 100 𝑠

𝜃𝑜 = 30𝑜
𝑉𝑜 2 𝑠𝑖𝑛Ѳ𝑜 (100)2 𝑠𝑖𝑛(2𝑥30)
𝑅 = = = 𝟖𝟖𝟑𝒎
𝑔 9.81
27. The property of a material which allows it to be drawn into a smaller section is called
A. Plasticity B. Ductility C. Elasticity D. Malleability

28. When a body is subjected to three mutually perpendicular stresses, of equal


intensity, the ratio of direct stress to the corresponding volumetric strain is known as
A. Young’s modulus C. Bulk Modulus
B. Modulus of Rigidity D. Poisson’s ratio

29. A diagram which show the variations of the axial for all sections of the span of a
beam, is called
A. Bending moment diagram C. Thrust diagram
B. Shear force diagram D. Stress diagram

30. The ratio of the lateral strain to the linear strains is


A. modulus of elasticity C. bulk modulus
B. modulus of rigidity D. Poisson’s ratio

31. What is an annuity?


A. the future worth of a present amount
B. an annual repayment of a clan
C. a series of uniform amounts over a period of time
D. the present, worth of a future amount

32. Which of the following closely related to d’Alembert’s theorem?


A. Newton’s first law of motion C. Newton’s third law of motion
B. Newton’s second law of motion D. Bernouli’s theorem

36
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
33. Accumulate P6,000 at the end of 12 years at an interest rate of 10 percent.
Solution:
𝐹 = 𝑃 (1 + 𝑖)𝑛
𝐹 = 6000 (1 + 0.10)12
∴ 𝑭 = 𝟏𝟖, 𝟖𝟑𝟎. 𝟓𝟕
34. A train whose speed is 60 mph rounds a curve whose radius of curvature is 484ft.
What is its acceleration?

Solution:
5280 𝑓𝑡
𝑉 = 60 𝑚𝑝ℎ 𝑥
3600 𝑠𝑒𝑐
𝑓𝑡
𝑣2 (88 𝑠𝑒𝑐 )2 𝒇𝒕
𝑎 = = = 𝟏𝟔
𝑟 484 𝑓𝑡 𝒔𝒆𝒄𝟐

35. Find the maximum shearing stress in a steel shaft of 2” in diameter which transmits
200 horsepower at 875 rpm.

Solution:

2𝜋𝑁𝑇 200(44760)
𝐻𝑃 = ;𝑇 = = 1628.29 𝑁 − 𝑚
44760 2𝜋(875)
100 𝑐𝑚 1 𝑖𝑛 1 𝑙𝑏
𝑇 = 1628.29 𝑁 − 𝑚 𝑥 𝑥 𝑥 = 14405.82 𝑙𝑏 − 𝑖𝑛
1𝑚 2.54 𝑐𝑚 4.45 𝑁
16 𝑇𝑚𝑎𝑥 16 ( 14405.82)𝑙𝑏−𝑖𝑛
𝑆𝑠𝑚𝑎𝑥 = =
𝜋𝐷 3 𝜋(2)3

𝑺𝒔𝒎𝒂𝒙 = 𝟗𝟏𝟕𝟏 ≈ 𝟗𝟏𝟔𝟗. 𝟖 𝒑𝒔𝒊


36. It state that if two bodies are in thermal equilibrium with a third body, they are also in
thermal equilibrium with each other.
A. first law of thermodynamics C. third law of thermodynamics
B. zeroth law of thermodynamics D. second law of thermodynamics

37. A fluid mass of 1500 kg occupies 2 cu. m. Its specific gravity is nearest
Solution:
𝑚 1500 𝑘𝑔 𝑘𝑔
𝑃𝑥 = = = 750
𝑣 2 𝑚3 𝑚3
𝑘𝑔
𝑃𝑥 750
𝑚3
Sg = 𝑃 = 𝑘𝑔 = 0.75
ℎ2𝑜 1000 3
𝑚

37
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
38. The opposite of alkali.
A. Acid B. Base C. Fluid D. Substance

39. The viscosity of fluid varies with


A. temperature C. density
B. pressure D. temperature and pressure

40. The New Electrical Engineering Law 7320 originated from House Bill No. ______ &
Senate Bill No. ______.
A. 11063 & 1766 B. 11063 & 1870 C. 11070 & 1871 D. 11070 & 1875

41. The Implementing Rules and Regulations (IRR) of RA 7920 was approved under
Board Resolution No. ____ series of 1995.
A. 16 B. 18 C. 22 D. 24

42. The first metal used by man was


A. Iron B. Copper C. Gold D. Bronze

43. Article II of Code of Ethics for Electrical Engineers contains:


A. SEC. 1 to 8 B. SEC. 1 to 6 C. SEC. 1 to 9 D. SEC. 1 to 7

44. Article IV, Rule _____ Requirements for examination as a REE.


A. 14 B. 15 C. 16 D. 17

45. Compute the value of the shear modulus G of steel whose modulus of elasticity E is
200 GPa and Poisson’s ratio u is 0.30
A. 72,456 MPa B. 76,923 MPa C. 79,698 MPa D. 82,400 MPa

Solution:
𝐸 200 𝑥 109
𝐺 = = = 𝟕𝟔, 𝟗𝟐𝟑 𝑴𝑷𝒂
2 + 2𝜇 2 + 2(0.3)
46. A type of annuity where the payments are made at the start of each period,
beginning from the first period
A. Ordinary annuity C. Deferred annuity
B. Annuity due D. Perpetuity

47. In electrochemistry oxidation is a loss of ____________.


A. electron B. proton C. Ion D. anode

48. The cycle generally used for gas turbines is


A. Rankine cycle B. Carnote cycle C. Otto cycle D. Brayton cycle

38
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
49. A Carnot engine operates between 800 K and 200 K. If t absorb 8 kJ of h at in each
cycle, the work it does per cycle is

Solution:
𝑄𝑛𝑒𝑡 𝑇𝑙
𝑛= = 1−
𝑊𝑛𝑒𝑡 𝑇ℎ
𝑄𝑛𝑒𝑡 200 𝐾
𝑛= =1−
8 𝑘𝐽 800 𝐾
𝑸𝒏𝒆𝒕 = 𝟔𝒌𝑱
50. An object weighs 100lb in air and 25 lb in fresh water. Its volume in cubic feet is
closest to

Solution:

BF = 𝑊𝑎𝑖𝑟 − 𝑊𝑎𝑖𝑟 = 100 - 25 = 75 lbs


𝑙𝑏
BF = 𝛿 𝑉𝐵 ; 75 lbs = 62.4 𝑓𝑡 3 (𝑉𝐵 )

𝑽𝑩 = 𝟏. 𝟐 𝒇𝒕𝟑
51. What is PDC stands for in EPIRA?
A. Philippine Distribution Commission C. Philippine Distribution Committee
B. Philippine Distribution Code D. Philippine Distribution Coordination

52. Add (10011) base 2 to (25) base 8. Express the answer in base 16
Solution:
100112 + 0101012 = 101000
100112 + 258 = 𝟐𝟖𝟏𝟔
53. The color of zinc is:
A. greyish white B. greenish white C. bluish white D. yellowish white

54. Which of the following computer language is used for artificial intelligence?
A. FORTAN B. PROLOG C. C D. COBOL

55. The maximum moment induced in a simply supported beam of 20 foot span, by a
5,000 pound load at midspan is

Solution:

𝑊𝐿 5000 𝑙𝑏 (20𝑓𝑡)
m= 4
= 4
= 25,000 lb-ft

39
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
56. A helical spring is made by wrapping steel wire 20mm diameter around a forming
cylinder 150mm in diameter. Compute the number of turns required to permit an
elongation of 100mm without exceeding a shearing stress of 140 MPa. Use G = 83
GPa.
A. 12.18 B. 18.12 C. 13.83 D. 18.33

Solution:

0.15+0.02
R= = 0.085m
2

16 𝑃𝑅 0.5
𝑆𝑠𝑚𝑎𝑥 = 4
(1 + )
𝜋𝑑 𝑚
16 𝑃(0.085) 0.5
140 𝑥 106 = (1 + )
𝜋(0.02)2 2(0.085)
0.02
P = 2443.46
64𝑃𝑅 3 𝑛
𝛿=
𝐺𝑑 4
64(2443.46)(0.85)3 𝑛
0.1 =
(83 𝑥 109 )(0.02)4
n = 13.83
57. What is that maximum deflection, in cm, of a simply supported, 6m long steel beam
with a 5 cm x 5 cm cross-section if it has 2000 N load at the midpoint?
A. 6.35 B. 7.02 C. 7.63 D. 8.23

Solution:

58. During an isentropic expansion of air, the volume triples, if the initial temperature is
200 deg. C1 find T2 in deg C.

Solution:
𝑇2 𝑉
= (𝑉1 )𝑘−1 , 𝑘𝑎𝑖𝑟 =1.4
𝑇1 2

𝑇2 + 273 𝑉1
= ( )1.4−1
200 + 273 1𝑉1
𝑇2 = 𝟑𝟐𝒐 𝑪
59. A certain water faucet has 7 gmp flow rate. How many minutes can it fill a cubic
meter drum?

40
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:
𝑣 3.785𝐿 𝑚3
𝑄 = 𝑡 ; Q = 7gpm x 𝑥
𝑔 1000𝐿

𝑚3
𝑡=
𝑚3
9.26495 𝑚𝑖𝑛

∴ 𝒕 = 𝟑𝟕. 𝟕𝟒 𝒎𝒊𝒏𝒔
60. The atmospheric pressure at sea level is
A. 103 kN/m^2 C. 760 mm of mercury
B. 10.3 m of water D. all of these

61. Property of a fluid by which its own molecules are attracted is called
A. Adhesion B. Cohesion C. Viscosity D. Compressibility

62. If a 1/3 hp pump runs for 20 minutes what is the energy used?
A. 0.06 ergs B. 0.25 kN C. 0.30 MJ D. 0.11 kWhr

Solution:
1 746 𝑊 60 𝑠𝑒𝑐𝑠
𝐻𝑃 𝑥 20 𝑚𝑖𝑛𝑠 𝑥 𝑥 = 𝟎. 𝟑𝟎 𝑴𝑱
3 𝐻𝑃 𝑚𝑖𝑛𝑠

63. At an annual rate of return of 8 percent, what is the future worth of $100 at the end
of four years?
A. $ 130 B. $ 132 C. $ 135 D. $ 136
Solution:
𝐹 = 𝑃(1 + 𝑖)𝑛
𝐹 = 100(1 + 0.08)4
F = 136
64. Structural steal elements subjected to torsion develop
A. tensile stress C. shearing stress
B. compressive stress D. bending stress

65. You deposit $1000 into a 9 percent account today. At the end of two years, you will
deposit another $3000. In five years you plan a $4000 purchase. How much is left in
the account one year after the purchase?
A. $925 B. $1424 C. $1552 D.1691
Solution:
𝐹𝑇 = 𝐹1 + 𝐹2 − 𝐹3

41
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

𝐹𝑇 = [(1000(1 + 0.09))) (1 + 0.09)5 + 3000(1 + 0.09)3 ] − 4000

𝐹𝑇 = 𝟏𝟓𝟔𝟐 ≈ 𝟏𝟓𝟓𝟐

66. In flow process, neglecting KE and PE changes - ∫ 𝑉𝑑𝑃 represents which item
A. heat transfer C. closed system work
B. shaft work D. flow energy

67. If you borrow money from your friend with, simple interest of 12 percent, find the
present worth of P20,000 which is due at the end of nine months
A. P18,992.08 B. P18,782.18 C. P18,348.62 D. P18,120.45

Solution:
𝐼 = 𝑃(1 + 𝑖𝑛)
9 −1
𝑃 = 2000(1 + 0.12( ))
12
P = 18,348.62
68. A car starts from rest and moves with a constant acceleration of 6 m/s^2. What is the
speed of the car after 4 seconds?
A. 18 m/s B. 24 m/s C. 35 m/s D. 64 m/s
Solution:
𝑣
𝑎 =
𝑠
𝑚 𝒎
𝑣 = (6 2 )(4𝑠) = 𝟐𝟒
𝑠 𝒔

69. Which of the following is spreadsheet software?


A. Microsoft Word B. Notepad C. Microsoft Excel D. Power Point

70. A load of P5,000 is made for a period of 15 months, at a simple interest rate of 15
percent, what future amount is due at the end of the loan period?
A. P5,937.50 B. P5,873.20 C. P5,712.40 D. P5,690.12

Solution:
15
𝐼 = 𝑃(1 + 𝑖𝑛) = 5000(1 + 0.15( )) = 𝟓, 𝟗𝟑𝟕. 𝟓𝟎
12
71. Waves in a lake are 5.00 m in length and pass an anchored boat 1.25 s apart. The
speed of the wave is
A. 0.25 m/s B. 4.00 m/s C. 6.25 m/s D. 5.75 m/s

42
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝑑 5𝑚 𝒎
𝑉 = = 1.2𝑠 = 𝟒. 𝟎𝟎
𝑡 𝒔

72. Before starting any installation work, alteration, repair or extension any electrical
system, what type of permit is needed?
A. Building permit B. Working permit C. Electrical permit D. Mayor’s permit

73. A computer __________ is self-replicating computer program.


A. Viruses B. Worms C. Spyware D. Malware

74. Oxygen boils at -183 deg C. This temperature is


A. -215 deg F B. -297 deg F C. -329 deg F D. -361 deg F
Solution:
9 𝑜
𝐹 = ( 𝐶 + 32)
5
9
𝐹 = ( −187 + 32) = −𝟐𝟗𝟕. 𝟒𝒐 𝑭
5
75. 3.0 lbm of air are contained at 25 psia and 100 deg F. what is the volume of the
container?
A. 10.7 𝑓𝑡 3 B. 14.7 𝑓𝑡 3 C. 15 𝑓𝑡 3 D. 24.9 𝒇𝒕𝟑
Solution:

𝑝𝑉 = 𝑚𝑅𝑇
𝑙𝑏𝑓 12 𝑖𝑛 2 𝑓𝑡 − 𝑙𝑏𝑓
25 2 𝑥 ( ) (𝑣) = 3 𝑙𝑏𝑚 (53.34 )(460 + 100)𝑜 𝑅
𝑖𝑛 1 𝑓𝑡 𝑙𝑏𝑚𝑜 𝑅
𝑽 = 𝟐𝟒. 𝟗 𝒇𝒕𝟑
76. A 3.0-kg object is initially at rest. It then receives an impulse of 15 Ns. after the
impulse, the object has

A. a speed of 45 m/s.
B. a momentum of magnitude 5.0kgm/s
C. a speed of 7.5 m/s.
D. a momentum of magnitude 15kgm/s
Impulse = momentum

77. A glass of ice water is filled to the brim with water, the ice cubes stick up above the
water surface. After the ice melts, which is true?
A. The water level is below the top of the glass.
B. The water level is at the top of the glass but no water has spilled.

43
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
C. some water has spilled over the side of the glass.
D. Impossible to say without knowing the initial densities of the water and ice.

78. A cyclist’s average metabolic rate during a workout is 500 W. if the cyclist wishes to
expand at least 300 kcal of energy, how long must the cyclist exercise at this rate?
A. 0.6min B. 3.6 min C. 36.0 min D. 41.9 min
Solution:
𝑊
=
𝑃
300 𝑘𝐶𝑎𝑙 1 𝑘𝑊ℎ 60 𝑚𝑖𝑛𝑠
𝑡 = 𝑥 𝑥
500 𝑥 10−3 𝑘𝑊 860 𝑘𝐶𝑎𝑙 1 ℎ𝑟
𝒕 = 𝟒𝟏. 𝟗 𝒎𝒊𝒏

79. A force of 10 N is applied to one end of a 10 in diameter circular rod. Calculate the
stress.
A. 0.15 kPa B. 0.10 kPa C. 0.20 kPA D. 0.05 kPa
Solution:

𝑃
𝑆 =
𝐴
10 𝑁
𝑆 =
2.54 𝑚
𝜋(10 𝑖𝑛 𝑥 100 )2
4

𝑺 = 𝟎. 𝟐 𝒌𝑷𝒂
80. Battery acid is the common name for
A. formic acid B. hydrochloric acid C. nitric acid D. sulphuric acid

81. For school buildings, the general lighting load is _____ VA per square meters.
A. 24 B. 28 C. 16 D. 8

82. Calculate the volume at STP of 26.7 g of oxygen gas.


A. 17.8L B. 87.1L C. 18.7L D. 78.1L
Solution:
𝑉 = 𝑚𝑅𝑇 = 𝑛𝑅𝑇 @ 𝑠𝑡𝑝 𝑃 = 1 𝑎𝑡𝑚 𝑇 = 0𝑜 𝐶
26.7 𝑔 𝐽
(101.325 𝑘𝑃𝑎)(𝑉) = ( ) (8.314 𝑜
) (0 + 273𝑜 𝐾)
2 𝑥 10 𝑚𝑜𝑙 𝑅

44
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
1000 𝐿
𝑉 = 0.0187 𝑚3 𝑥 = 𝟏𝟖. 𝟕 𝑳
𝑚3

83. Sec. 34 of Art. IV: Sundry Provision Relative to Practice of Electrical Engineering
states that _________.
A. Personnel required
B. Preparations of plans, supervision of installation, application of PEC code
C. Practice not allowed for firms and corporations
D. Prohibitions in the Practice of Electrical Engineering

84. An iron plate 2 cm thick has a cross-section of 5,000 sq. cm. One face is at 150 deg
C, and the other is at 140 deg C. How much heat passes through the plate each
second? For iron, 𝑘𝑇 = 80 W/m-K.
A. 20 kJ/s B. 16 kJ/s C. 27 kJ/s D. 36 kJ/s
Solution:
∆𝑄 ∆𝑇 𝑚2
= 𝐾𝑇 𝐴 ( ) = 80 (5000 𝑐𝑚2 𝑥 )
∆𝑡 𝑡ℎ 1002 𝑐𝑚2
∆𝑸 𝒌𝑱
= 𝟐𝟎
∆𝒕 𝒔

85. Determine the moment of inertia of a circle of diameter 5 in about a diameter.


A. 30.4 𝒊𝒏𝟒 B. 61.4 𝑖𝑛4 C. 15.35 𝑖𝑛4 D. 46.02 𝑖𝑛4
Solution:
𝜋𝑑 4 𝜋(5 𝑖𝑛)4
𝐼 = = = 𝟑𝟎. 𝟒 𝒊𝒏𝟒
64 64
86. RA 7920 Rule 2(d) defining?
A.CHED B. Commission C. Board of EE D. TESDA

87. Which wave requires a medium for transmission?


A. light B. Infrared C. radio D. sound

88. A machine has an initial cost of P50,000.00 and a salvage value of P10,000.00 after
10 years. What is the book value after 5 years using straight line depreciation?
A. P35,000.00 B. P25,000.00 C. P15,000.00 D. P30,000.00
Solution:
𝐶𝑜 − 𝐶𝑙 50,000 − 10,000
𝑑 = = = 4,000
𝐿 10
𝐷𝑛 = 𝑛𝑑 = 5(4,000) = 20,000
𝐶5 = 𝐶𝑜 − 𝐷𝑛 = 50,000 − 20,000 = 𝟑𝟎, 𝟎𝟎𝟎

45
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
89. If the atomic weight of magnesium is 24.3 g/mol,calculate how many magnesium
atoms does 5 g represent?
A.1.24x10^23 atoms C. 3.44x10^23atoms
B.1.76x10^23atoms D. 2.76x10^23atoms
Solution:
5𝑔
𝑛 𝑔
24.3
𝑀𝑎𝑔𝑛𝑒𝑠𝑖𝑢𝑚 𝐴𝑡𝑜𝑚𝑠 = 𝑀𝑊 = 𝑚𝑜𝑙 = 𝟏. 𝟐𝟒 𝒙 𝟏𝟎𝟐𝟑 𝒂𝒕𝒐𝒎𝒔
𝑃𝑟𝑜𝑡𝑜𝑛 1.673 𝑥 10−24 𝑔

90. What annuity is required over12 years to equate with a future amount of P 20,000?
Assume I=6 % annually
A. P1,290.34 B. P1,185.54 C. P1,107.54 D. P1,205.74
Solution:
(1 + 𝑖)𝑛 − 1 −1
= 𝐹( )
𝑖
(1 + 0.06)12 − 1 −1
𝐴 = 20,000 ( ) = 𝟏, 𝟏𝟖𝟓. 𝟓𝟒
0.06
91. The iron that has been cooled quickly from a molten state is known as
A. Blue cast iron B. Pink Cast Iron C. Brown Cast Iron D. White cast iron

92. What is the speed of sound through a compressed water (100kpa),If it's volume
decreased by 0.007 % of it's original volume?
A.1244.55m/s B. 1414.23m/s C. 1195.23m/s D. 1395.11 m/s
Solution:

∆𝑃 100 𝑥 103
𝐾 √ ∆𝑉 √ 0.007 𝒎
= √ = 𝑉 = 100 = 𝟏𝟏𝟗𝟓. 𝟐𝟑
𝑃 𝑃 1000 𝒔

93. What does the prefix Tera refers to?


A. 10^12 B.10^15 C. 10^-12 D. 10^-15

94. What is the minimum diameter of solid steel shaft that will not twist through more
than 3 degrees in na 6m lengthwhen subjected to a torque of 14kN-m?
A.0.216m B. 0.018m C. 0.118m D. 0.034m
Solution:
𝑇𝐿
=
𝐽𝐺

46
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝜋𝐷4
𝐽 =
32
𝜋 𝜋
𝜃 = 3𝑜 𝑥 =
180𝑜 60
𝜋 (14 𝑥 103 )(6)
=
60 𝜋𝐷4
( 32 )(83 𝑥 109 )

𝑫 = 𝟎. 𝟏𝟏𝟖𝟒𝟓

95. What is PSALM in EPIRA strand for?


A. Private sector Assets and Liabilities Management
B. Private section Assets and Liabilities Management
C. Power sector Assets and Liabilities Management
D. Power section Assets and Liabilities Management

96. What is molarity of the solution if 150g of KCI is dissolved in water to make 800ml
solution?
A. 2.51 moles/L B. 2.25 moles/L C. 2.87 moles/L D. 1.53 moles/L
Solution:
𝐾 − 40 𝑥 1
𝐶𝑙 − 35 𝑥 1
𝑔
75 𝑚𝑜𝑙
𝑚 150 𝑔
MW = ;𝑛 = 𝑔 = 2 𝑚𝑜𝑙
𝑛 75
𝑚𝑜𝑙

𝑛 2 𝑚𝑜𝑙 𝒎𝒐𝒍
MR = = = 2.5
𝐿 800 𝑥 10−3 𝐿 𝑳

97. Article V of Code of ethics stated that:


This code shall take effect upon approval by the __________ and after (15) days
following it's publication in the Official Gazette.
A.Commission B. PRC C. IIEE. D. CHED

98. What is the temperature rating of THHN insulation?


A. 60degC B. 90 deg C C. 85 deg C D. 75 deg C

99. A turbine starts from rest to 180 rpm in 6 min at a constant acceleration. Find the
number of revolution that it makes within the elapse time.

47
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 550 B. 540 C. 630 D. 500

Solution:
𝑟𝑒𝑣
80 𝑥 6 𝑚𝑖𝑛 = 1080 𝑟𝑒𝑣
𝑚𝑖𝑛
0 + 6
∆𝑡 = = 3 𝑚𝑖𝑛𝑠
2
𝑟𝑒𝑣
180 𝑥 3 𝑚𝑖𝑛 = 𝟓𝟒𝟎 𝒓𝒆𝒗
𝑚𝑖𝑛

100. A nozzle with a 2cm diameter outlet is attached to a 10 cm diameter hose. If


the exit velocity is 50 m/s, the force of the water on the nozzle is nearest.
A. 9050N B. 7500 N C. 2420 N D.750 N

Solution:
𝑣2
𝐹 = 𝛿𝐴ℎ = 𝛿𝐴
2𝑔
𝜋(0.12 − 0.022 ) (502 ) − (2)2
𝐹 = ( 9800)( )( )
4 2(9.8)
𝑭 = 𝟗𝟒𝟏𝟗 𝑵 ≈ 𝟗𝟎𝟓𝟎 𝑵

48
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM MARCH 2017

1. The executive officer of the Board of Electrical Engineering is _______.


A. PRC Commissioner C. Civil Service Comission
B.Chairman of the Board of EE D. IIEE President

2. The differential of the shear stress equation is which ones of the following
A. load on the beam C. bending moment of the beam
B.tensile strength of the beam D. slope of the elastic curve

3. The differential of the shear stress equation is which ones of the following
A. load on the beam C. bending moment of the beam
B. tensile strength of the beam D. slope of the elastic curve

4. The conductor used to connect the grounding electrode to the equipment grounding
conductor, to grounded conductor, or to both, of the circuit at the equipment or at
the source of a separated derived system.
A. Grounded Conductor C.Equipment Grounding Conductor
B. Grounding Conductor D. GroundingElectrode Conductor

5. Motors must be labelled with the following: nameplate rating, manufacturer’s name
and etc.
A. manufacturing rule C. wiring design rule
B. construction rule D. installation

6. Which of the following is not a part of the requirements to take RME?


A. Take 1-year electrician’s course and 3-years apprenticeship
B. Take 2-year electrician’s course and 2-years apprenticeship
C. Take 3-years of BSEE with apprenticeship
D. Graduate BSEE

7. What is the primary purpose of PEC?


A. to serve as guide for the untrained personell
B. is to conserve electrical energy
C. is the practical safeguarding of persons and property
D. to serve as manual guide for design

8. The process of outsmarting the search engine.


A. Google Fooling C. Search Engine Optimization
B. Rank Enhancement D. Search Engine Hacking

9. The Board of Electrical Engineering is composed of one chairman and how many
members?
A. 2 B. 3 C.4 D. 5

49
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
10. Process of posting latitude and longitude to pictures and images.

A. Prodcasting B.Geotagging C.Flagging D. Posting

11. A price tag of P1450 is paid in 70 days, but if paid within 35 days it will have a 5
percent discount. Find the rate of interest.
A. 52.3% B. 69.20% C. 54.13% D. 59.7%

Solution:

𝐷𝑖𝑠𝑐𝑜𝑢𝑛𝑡 = 0.05(14500) = 72.50


𝐼 = 𝑃𝑟𝑡
35
72.50 = 1377.5 (𝑟) ( )
360
∴ 𝑹 = 𝟎. 𝟓𝟒𝟏𝟑 𝒐𝒓 𝟓𝟒. 𝟏𝟑

12. You are standing on a bathroom scale in an elevator. In which of these situations
must then be the same as when the elevator is at rest?
A. Moving up at constant speed C. Moving down with increasing speed
B. Moving up with increasing speed D. In free fall (after elevator cable)

13. Which one is the portion of an instruction cycle where the instruction is sent from
memory to register?
A. load B. Accumulate C. execute D. fetch

14. For REE board examination, the passing general average is 70 percent provided
there is no ________ in any of the 3 subjects.
A. 50 percent B. 60 percent C. 65 percent D. 40 percent

15. What is the weight percent of mathematics subjects?


A. 40 B. 30 C. 45 D. 25

16. A beam with rectangular cross-section with breadth of 20cm. Determine the depth
of the beam if the maximum shearing stress in the beam is 30 kg/cm2 and Vmax=
10,000 kg.
A. 25 cm B. 23 cm C. 20 cm D. 30 cm

Solution:
𝐹
𝐴𝑚𝑎𝑥 = (1.5) ( )
𝑏𝑑
10,000 𝑘𝑔
30𝑘𝑔/𝑐𝑚^2 = (1.5) ( 20 𝑘𝑔 )
∴ 𝑫 = 𝟐𝟓𝒄𝒎

50
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
17. What percentage of the human body will float in fresh water? Average density of
human body is 980 kg/cu. m.
A. 98 B. 2 C. 96 D. 4

Solution:
𝑃 980
%𝑔𝑎𝑔𝑒 = 𝑃𝐻20 − ℎ𝑢𝑚𝑎𝑛𝑏𝑜𝑑𝑦 = 1000 −
𝑃𝐻 20 1000
∴ %𝒈𝒂𝒈𝒆 = 𝟐
18. A bank is advertising 9.5 percent account that yield 9.84 percent account that yield
9.84 percent annually. Find how often interest is compounded.
A. Monthly B. Bimonthly C. Quarterly D. Annually

Solution:

19. What is work-in-process classified as?


A. an asset B. a liability C. an expense D. owner’s equity

20. What is the formula for a straight-line-depreciation rate?

𝟏𝟎𝟎 % − 𝐩𝐞𝐫𝐜𝐞𝐧𝐭 𝐧𝐞𝐭 𝐬𝐚𝐥𝐯𝐚𝐠𝐞 𝐯𝐚𝐥𝐮𝐞


𝐀.
𝒆𝒔𝒕𝒊𝒎𝒂𝒕𝒆𝒅 𝒔𝒆𝒓𝒗𝒊𝒄𝒆 𝒍𝒊𝒇𝒆

percent net salvage value


B.
𝑒𝑠𝑡𝑖𝑚𝑎𝑡𝑒𝑑 𝑠𝑒𝑟𝑣𝑖𝑐𝑒 𝑙𝑖𝑓𝑒
100 percent net salvage value
C.
𝑒𝑠𝑡𝑖𝑚𝑎𝑡𝑒𝑑 𝑠𝑒𝑟𝑣𝑖𝑐𝑒 𝑙𝑖𝑓𝑒

average net salvage value


D.
𝑒𝑠𝑡𝑖𝑚𝑎𝑡𝑒𝑑 𝑠𝑒𝑟𝑣𝑖𝑐𝑒 𝑙𝑖𝑓𝑒

21. HTTP.// is an identifier that appears at the beginning of most Web page. What does
HTTP stands for?
A. Hypertext Time Protocol C. Hypertext Transmission Process
B. Hypertime Text Protocol D. Hypertext Transfer Protocol

22. For a fluid, viscosity is defined as the constant of proportionality between shear
stress and what other variable?
A. the spatial derivative of velocity C. the time derivative of density
B. the time derivative of pressure D. the spatial derivative of density

23. You need P40,000 per year for four years to go to college. Your father invested
P50,000 in a 7 period account for your education when you were born. If you
withdraw the P40,000 at the end of your 17th,18th,19th , and 20th years, how much
money will be left in the account at the end of your 21styear?
A. P17,000 B. P25,000 C. P34,000 D. P40,000

51
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝑃17 = 50,000(1 + 0.07)17 − 40,000
𝑃18 = 𝑃17 (1 + 0.07) − 40,000
𝑃19 = 𝑃18 (1 + 0.07) − 40,000
𝑃20 = 𝑃19 (1 + 0.07) − 40,000
𝑃20 = 15,886.50
𝑃21 = 15,886.50(1 + 0.07)
∴ 𝑷𝟐𝟏 = 𝟏𝟔, 𝟗𝟗𝟖. 𝟓𝟔

24. A loan of P4,000 is made for a period of 16 months at a simple discount rate of 7
percent, what future amount is due at the end of the loan period?
A. P3,635.18 B. P3,598.57 C.P4446.22 D.P4411.76

Solution:

𝑃 = 4000
𝑑 = 7%
𝑛 = 16 𝑚𝑜𝑛𝑡ℎ𝑠
𝑖 =?
𝐹 =?
𝐹 = 𝑃 × (1 + 𝑖𝑛)
𝑑 16
𝐹 = 𝑃 × [1 + ( ) ( )]
1 − 𝑑 12
. 07 16
𝐹 = 4000 × [1 + ( ) ( )]
1 − .07 12

𝑭 = 𝟒, 𝟒𝟎𝟏. 𝟒𝟑 𝒐𝒓 𝟒, 𝟒𝟏𝟏. 𝟕𝟔

25. The thermodynamic statement of the conservation of energy of the system is the
A. first law B. second law C. third law D. zeroth law

26. In sizing of wire, this is:


A. manufacturing rule C. wiring design rule
B. construction rule D. installation rule

27. Express a pressure gage reading of 35 psi in absolute kPa?


A. 218 B. 182 C. 341 D. 314

Solution:
𝑃𝑔 = 35 𝑝𝑠𝑖
𝑃𝑎𝑏𝑠 = 𝑃𝑔 + 14.7𝑝𝑠𝑖
𝑃𝑎𝑏𝑠 = 35𝑝𝑠𝑖 + 14.7𝑝𝑠𝑖
𝑃𝑎𝑏𝑠 = 49.7𝑝𝑠𝑖
101.3𝑘𝑃𝑎
𝑃𝑎𝑏𝑠 = 49.7𝑝𝑠𝑖 ×
14.7𝑝𝑠𝑖

52
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑷𝒂𝒃𝒔 = 𝟑𝟒𝟏𝒌𝑷𝒂

28. Find the value of J in the program:


I= 1
J= 0
15 J= J**2 + I**2 IF (I.EQ.3) GO TO 16
I=I + 1
GO TO 15
16 CONTINUE

A. 34 B. 9 C. 40 D. 15

29. Galvanized steel are products coated with ______.


A. Carbon B. Sulfur C. Zinc D.Nickel

30. Which of the following materials is not viscoelastic material?


A. Glass B. Rubber C. Metal D.Plastic

31. Which is the study of heat and transformation of energy?


A. Thermodynamics B. Thermophysics
C. Thermoplastic D. Thermochemistry

32. Which of the following may be the Poisson’s ratio of material?


A. 0.52 B. 0.56 C. 0.63 D. 0.35

33. A property of a material which it can be rolled a wire?


A. Ductility B. Malleability C. Lustre D. Elasticity

34. What is a measure of the average speed with which accounts receivable are
collected?
A. Current Ratio B. Quick Ratio
C. Acid test ratio D. Receivable turnover

35. What do you call the ratio of income to owner’s equity?


A. return of investment B. gross margin
C. rate of return D. interest expense

36. What is the minimum height of the track of a roller coaster such that it can go
around a loop without off or going off the track?
1 𝟓 1
A. h= 2r B. h=𝟐r C. h = r D. h = 4r

37. What is the old Electrical Engineering Law?


A. RA 814 B. RA 184 C. RA 9136 D. RA 7920

38. What is another term for “acid-test ratio”?

53
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Current Ratio B. Quick Ratio
C. Profit Margin Ratio D. Price-earning model

39. A line ground system, the white conductor that carries current in normal operation
is?
A. neutral B. ground C. grounding conductor D. grounding elec

40. A 4-wire system has a high-leg voltage that is indicated by a wire of color ______.
A. black B. orange C. brown D. red

41. What are considered as the “building blocks” for engineering materials?
A. Atoms B. Elements C. Matters D. Compounds

42. Which of the following is not a structural class of steels?


A. tool and die C. carbon
B. high strength, low strength carbon D. stainless

43. Defects seen by optical or electron microscope


A. alteration B. aberration C. atomization D. deformation

44. Which is not a programming language in web development?


A. XMLB. Elements B. FORTRAN C. HTML D. Javascript

45. Which is not used in programming application?


A. C B. Java C. Oracle D. Visual Basic

46. What size in AWG should the wire be for 70 A overcurrent protection device?
A. 8 B.6 C. 4 D. 3

47. In the wiring of PEC 2009, what is the version of National Electrical Code that was
patterned to?
A. 2008 B.2005 C. 2001 D. 2002

48. A 50-kg metal cylinder, 2.0m long and with each end of area 25 sq. cm.
stands vertically on one. What pressure does the cylinder exert on the floor?
A. 98.1 kPa B. 784.8 kPa C. 392.4 kPa D. 196.2 kPa

Solution:
𝑓𝑜𝑟𝑐𝑒
Stress = 𝑎𝑟𝑒𝑎
50(9.81)
Stress = 11𝑚
(25 𝑥 )
100 𝑐𝑚
Stress = 196.2 Kpa

49. A cylinder weighs 150 lbf. Its cross-sectional area is 40 square inches. When the
cylinder stands on one end, what pressure does the cylinder on the floor?

54
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 52 kPa B. 26 kPa C. 14.1 kPa D. 63.2 kPa

Solution:
4.448 𝑁
𝐹 = 150𝑙𝑏𝑓 𝑥 𝐹 = 667.2 𝑁
11𝑙𝑏𝑓
𝑠𝑡𝑟𝑒𝑠𝑠
Stress = 𝑎𝑟𝑒𝑎
667.2
Stress = 2.54 2 1 2
40 𝑥 ( ) ( )
1 100
∴ 𝑺𝒕𝒓𝒆𝒔𝒔 = 𝟐𝟓𝟖𝟓𝟒. 𝟎𝟓𝟏𝟕𝟏 𝒐𝒓 𝟐𝟔 𝑲𝑷𝒂

50. After installing a new modem and router to a computer, what is the order of tuning
on?
A.Computer,Modem,Router B.Router, Modem,Computer
C.Modem,Computer,Router D.Modem,Router,Computer

51. A steel bar is 12m long @ -3.57 degree Celsius, what is the increase in
Length whrn the bar is heated to 5 degree Celsius the linear expansion for Steel α is
12 x 10^-6 degre Celsius
A.1.25cm B.1.25mm C.2.5cm 2.5mm

Solution:

𝜹 = 𝐿𝐶∆𝑡
𝜹 = 12(12𝑥10−6 )(5 + 3.57)
𝛿 = 𝟏. 𝟐𝟓 𝒎𝒎
52. Which of the following is the process that cannot found in a carnot engine cycle?
A.Isobaric Expansion B.Adiabatic compression
C.Adiabatic expansion D.Isothermal expansion

53. What is the branch circuit rating for hermetic motor 80 A?


A.80 B.92 C.100 D.120

54. The largest solid conductor for raceway is


A. 8 mm2 B. 5.5 mm2 C. 14mm2 D. 3.5 mm2

55. To consider as continuous load


A. 3 hours and more C. 5 hours or more
B. 4 hours and more D. 6 hours or more

56. How many branch circuits in 55 kVA load, with 220 v and 20 A branch circuit?
A. 12 B. 13 C. 14 D. 15

57. Find the specific volume of water with density of 1,000 kg/m3
A. 0.004 m3/kg C. 0.001 m3/kg

55
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
B. 0.002 m3/kg D. 0.003 m3/kg

58. NGCP warns _________ alert if tropical disturbance within 24 hours.


A. yellow C. red
B. blue D. weather disturbance

59. In computing, what is a tape drive?


A. a data storing device C. a pointing device
B. an OCR device D. a multimedia device

60. If the velocity of the flow in a 20 cm radius hose in a 1.2 m/s, what is the output
velocity in a 0.5 cm radius issuing from a nozzle attached at the end of the pipe?
A. 0.192 m/s B. 4.8 m/s C. 0.3 m/s D. 0.075 m/s

Solution:
𝑄1 = 𝑄2
𝐴1 𝑉1 = 𝐴2 𝑉2
𝜋 𝜋
(20)2 (1.2) = (50)2 (𝑉2 )
4 4
𝒎
𝑉2 = 𝟎. 𝟏𝟗𝟐
𝒔𝟐
61. Find the capacitance of the plates of a parallel-plate capacitor with an area of 40 sq.
cm. and 10 mm apart 𝜀o= 8.854 x 10-12 F/m.
A. 3.54 B. 35.4 C. 2.21 D. 22.1

Solution:
𝑸 𝐴
𝑪=𝑽=ε=ℎ
𝐶 = (8.854x10 − 12)(40
10
)
∴ 𝑪 = 𝟑. 𝟓𝟒𝟏𝟔𝒙𝟏𝟎 − 𝟏𝟏𝑭

62. The continuous current must not exceed ______ of the rating of the conductor?
A. 60 percent B. 70 percent C. 80 percent D. 90 percent

63. If a man’s body in a bathtub with 1,200 kg water loses heat at 4.2 x 10 6 J/hr. If the
initial temperature of water is 20oC, what will be its temperature after 1 hour?
A. 100 B. 120 C. 90 D. 70

Solution:
𝑘𝑔 L−atm.
64. Find the density of UFa (M = 352.02 𝑘𝑚𝑜𝑙) at 25oC and 1 atm. R* = 0.0821 𝑚𝑜𝑙−𝐾
A. 14.4 g/L B. 171.5 g/L C. 2.05 g/L D. 24.6 g/L

Solution:
𝑃𝑉 = 𝑚𝑅𝑇

56
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑘𝑔
𝑇 = 25𝑜𝐶 𝑀 = 352.02
𝑘𝑚𝑜𝑙
𝐿 − 𝑎𝑡𝑚.
𝑅 ∗ = 0.0821
𝑚𝑜𝑙 − 𝐾
𝐿 − 𝑎𝑡𝑚
0.0821
𝑅= 𝑚𝑜𝑙 − 𝐾 × 1000𝑔
𝑘𝑔 1𝑘𝑔
352.02
𝑘𝑚𝑜𝑙
𝑅 = 0.233 × 10 − 3 𝐿 − 𝑎𝑡𝑚⁄𝑘𝑔 − 𝑘

𝑚 𝑃
𝜌= =
𝑉 𝑅𝑇
1𝑎𝑡𝑚
𝜌=
𝐿 − 𝑎𝑡𝑚
(0.233 ) (25 + 275)𝐾
𝑔−𝑘
𝒈
∴ 𝝆 = 𝟏𝟒. 𝟒
𝑳
65. A motorcycle moves at a constant speed of v = 12 m/sec around a curved road of a
radius r= 100 m. What is the magnitude and general direction of the motorcycle’s
acceleration?
A. 1.4 m/s2 towards the center of the curvature
B. 1.4 m/s2 away from the center of curvature
C.1.1 m/s2 towards the center of curvature
D.1.1 m/s2 away from the center of the curvature

Solution:
𝒎
𝑽𝟐 (𝟏𝟐 )𝟐
𝒔
a= 𝒓 = = 1.44m/s2
𝟏𝟎𝟎𝒎

66. A flywheel with a moment of inertia of 2 kg-m3 is applied a torque of 5 N-m. If it


starts from rest, what is the speed of the flywheel, in rpm, after 5 seconds?
A. 29.67 B.119.36 C. 59/78 D. 92.76

Solution:
𝝉 = 𝒍𝒂
𝜏 5 𝑁−𝑚
𝑎= = = 2.5𝑟𝑎𝑑/𝑠 2
𝑙 2𝑘𝑔−𝑚3
at T=5 sec
60
𝑟𝑎𝑑 𝑟𝑎𝑑 𝑟𝑝𝑚
2𝜋
𝑺𝒑𝒆𝒆𝒅 = (2.5 ) (5𝑠𝑒𝑐) = 12.5 ∗ 1𝑟𝑎𝑑 = 𝟏𝟏𝟗. 𝟑𝟔 𝒓𝒑𝒎
𝑠2 𝑠
𝑠
67. _____________ is an act of sending e-mails or creating web pages that are
designed to collect an individual’s online bank, credit card or other login
information?
A. Malware B. Hacking C. Cracking` D. Phishing

57
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

68. The original amount of money invested, borrowed, or deposit


A. Interest B. Principal C. Funds D. Stock

69. The interest rate of return of a project that involves an initial investment with
subsequent positive cash flows is 18 percent. Four companies considering the
project. Given the following respective minimum attractive rates of return (MARR),
which company will be most likely to accept the project?
Company MARR
1. 12 percent
2. 14 percent
3. 18 percent
4. 19 percent
A. company A B. Company B C. Company C D. Company D

70. What is the amount of P12,800 in 4 years at 5 percent compounded quarterly?


A. P15,641.59 B.P15,614.59 C. P15,461.59 D. P15,146.95

Solution:

𝑁𝑜𝑚𝑖𝑛𝑎𝑙 𝑅𝑎𝑡𝑒 𝐼𝑛𝑡𝑒𝑟𝑒𝑠𝑡 0.05


𝑖= = = 0.0125
𝑀 4
𝐹 = 𝑃(1 + 𝑖)𝑛
𝐹 = 12800(1 +0.0125)16 = P15,614.59

71. A diagram drawn to help visualize and simplify problem having diverse receipts and
disbursement
A. Budget C.year-end-convention
B. investment D. Cash-flow

72. A loan of P5,000 is made for a period of 15 months, at a simple interest rate of 15
percent, what future amount is due at the end of the loan period?
A. P5,712.40 B. P5,690.12 C.P5,937.50 D. P5,873.20

Solution:
𝐹 = 𝑃 (1 + 𝑖𝑛)

= 5000[1 + (0.15)( )]
∴ 𝑭 = 𝑷𝟓, 𝟗𝟑𝟕. 𝟓𝟎

73. 3.0 lbm of air are contained at 25 psia and 100 deg F. Given that R air= 53.35 ft-
lbf/lbm-oR, what is the volume of the container?
A. 10.7 cu. ft. B. 14.7 cu. ft. C. 15 cu. ft. D. 24.9 cu. ft.
Solution:

58
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
74. Which of the following relations defines enthalpy?
A. h= u + 𝜌 B. h = u + 𝝆𝑽 C. h = u + 𝜌 D. h =𝜌𝑉+ T

75. What refers to chemically combined elements with definite proportions of the
component elements?
A. Mixture B. Molecules C. Compound D. Alloy

76. Which of the following cannot be a property of a gas?


A. Density B. Pressure C. Viscosity D. Temperature

77. The relationship between the extension of a spring and the force required to
produce the extension
A. F= ma B. F =𝜇𝑁 C. F= 𝑚𝑣 2 D. F = kx

78. The place where buyers and sellers are together.


A. Density B. Pressure C. Viscosity D. Temperature

79. The linear portion of the stress-strain diagram of steel is known as the
A. modulus of elongation C. Irreversible range
B. Plastic range D. elastic range

80. For which of the following is the Program-Evaluation and Review Technique
(PERT) not used?
A. construction projects C. preparation of bids and proposals
B. computer programming assignments D. queueing problems

81. In any collision, which of the following is conserved


A. kinetic energy B. velocity C. momentum D.potential energy

82. What is another term for modulus of elasticity?


A. Bulk modulus C. Constant of elongation
B. B. Shear strain D. Young’s Modulus

83. Which of the following is added to the drinking water distribution system for a
disfunction?
A. Soda ash B. Chlorine C. Lime D. Iodine

84. An enclosed channel designed expressly for holding wires, cables, or busbars with
additional functional permitted by the Philippine Electrical Code.
A. Duct B. Raceway C. Cable Tray D. Tube

85. Sec. 23 of Art. III of RA 7920: Issuance of Certificates of Registration. The


professional is required to review license every ___ years upon payment of
registration fees.
A. 1 B. 2 C. 3 D. 4

59
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS

86. A man borrowed P2,000 from a bank and promised to pay the amount for one year.
He received only the amount of P1,920 after the bank collected an advance interest
of P80.00. What is the rate of discount?
A. 4.17 B. 4.00 C.3.67 D. 4.50

Solution:

𝐹 = 𝑃(1 + 𝑖𝑛) ; 2,000 = 1920(1 + 𝑖(1)) ; 𝑖 = 0.0417


1 1
𝑹𝒂𝒕𝒆 𝒐𝒇 𝒅𝒊𝒔𝒄𝒐𝒖𝒏𝒕 = 1 − =1− = 𝟒%
1+𝑖 1 + .0417
87. Service conductors made up in the form of a cable
A. Service cable C. Service Drop
B. Service Raceways D. Service Lateral

88. For hospitals, a general lighting load of ___ VA/m2 shall be used.
A. 12 B. 24 C. 8 D. 16

89. A method of identifying the location of a given data record by its name.
A. Tracking B. Linker C. Signature D. Hashing

90. Dalisay Corporation’s gross margin is 45 percent of sales. Operating expenses such
as sales and administrations are 15 percent of sales. Dalisay is in 40 percent tax
bracket. What percent of sales is their profit after taxes?
A. 18 B. 5 C. 24 D. 0

Solution:

𝑃𝑒𝑟𝑐𝑒𝑛𝑡 𝑜𝑓 𝑠𝑎𝑙𝑒𝑠 𝑎𝑓𝑡𝑒𝑟 𝑝𝑟𝑜𝑓𝑖𝑡 𝑡𝑎𝑥𝑒𝑠 = (𝐺𝑟𝑜𝑠𝑠 𝑚𝑎𝑟𝑔𝑖𝑛 %)𝑥(% 𝑡𝑎𝑥 𝑏𝑟𝑎𝑐𝑘𝑒𝑡)
∴ 𝑷𝒆𝒓𝒄𝒆𝒏𝒕 𝒐𝒇 𝒔𝒂𝒍𝒆𝒔 𝒂𝒇𝒕𝒆𝒓 𝒑𝒓𝒐𝒇𝒊𝒕 𝒕𝒂𝒙𝒆𝒔 = (. 45)𝑥(. 40) = 𝟏𝟖%

91. Sec. 14(a) (iii) of Article III. Examination and Registration, states that prior to
commencing of work, the foreign professional shall secure special permit from the
______.
A.Commission B. IIEE C. PDEA D.Bureau of Immigration

92. The Professional Regulation Commission (PRC) was created under


A. PD 223 B. PD 29 C. EO 223 D. EO 59

93. A car dealer advertises the sale of a car model for a cash price of P280,000. If
purchased on installment the regular downpayment of 15 percent and balance
payable in 15 equal monthly installments at an interest rate of 1.5 percent per
month. How much will be required monthly payments?
A. P15,783.90 B. P15,632.11 C.P15,289.12 D. P15,185.78

60
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2017
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

94. The ratio of Cp and Cv is called


A. isothermal index B. Adiabatic index
C. Hypebeast index D. None of these

95. Which of the following is the opposite of elasticity?


A. rigidity B. malleability C. ductility D.plasticity

96. If 1/3 hp pump runs for 20 minutes, what is the energy used?
A. 0.06 erg B. 0.25 kw C. 0.30 MJ D. 0.11 kW-h

Solution:

1
𝑃= 𝑥 746 = 248.67
3
60𝑠𝑒𝑐
𝑡 = 2𝑂 𝑚𝑖𝑛𝑠 𝑥 = 1200𝑠𝑒𝑐
1 𝑚𝑖𝑛
𝐽 = 𝑊𝑡 = 248.67 𝑥 1200 = 𝟎. 𝟑𝟎 𝑴𝑱

97. What is the area under the curve on a temperature-entropy diagram?


A. Heat B. Work C. Entropy D. Volume

98. Which of the following refrigerant is highly toxic and flammable?


A. NH2 B. CO2 C. CO3 D. R-12

99. Oxygen is converted into ozone by


A. great heat B. high pressure C. electric discharge D. all of these

100. What rules are included in Article IV of RA 7920?


A. Rule 1 to 10 B. Rule 11 to 20 C. Rule 21 to 27 D. Rule 28 to 34

61
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM AUGUST 2016

1. Which location may be temporarily subjected to dampness or wetness?


A. Dry B. Damp C. Moist D. Wet

2. A train running at 60kph decelerated at 2.5m/min 2 for 12minutes. Find the distance
travelled in km within the period.
A.1.182 B.11.82 C.1.812 D.2.182

Solution:

Uniform Acceleration Formula


𝑺 = 𝑽𝐨(𝒕) ± 𝟏/𝟐𝒂(𝒕)2
60𝑘𝑚 1000𝑚 60,000𝑚 1ℎ𝑟 1000𝑚
𝑉𝑜 = 𝑥 = 𝑥 =
ℎ𝑟 1𝑘𝑚 ℎ𝑟 60 𝑚𝑖𝑛𝑠 𝑚𝑖𝑛𝑠
1000𝑚 1
=( ) (12min) − (2.5 𝑚/ min) (12min)2 = 𝟏𝟏. 𝟖𝟐𝟎 𝒌𝒎
min 2
3. Which of the following is very reactive in its pure form?
A. Na B. He C. HCl D. CO2

4. Which of the following is an instruction that causes data to be brought from memory
into an accumulator register?
A. LOAD B. LOOP C. FETCH D. JUMP

5. Installations underground or in concrete slabs or masonry in direct contact with earth.


A. Wet location B. Dry Location C. Damp Location D. Moist Location

6. MS-WORD is a type of?


A. System Software B. Operating System
C. Application Software D. System Software

7. What is CD-ROM?
A. Compact Disk Read Only Memory C. Compact Data Read Only Memory
B. Compatible Disk Read Only Memory D. Compatible Data Read Only Memory

8. What is the weight percentage of electrical engineering professional subjects?


A. 40 B. 35 C. 45 D. 25

9. In an ideal gas, both pressure and temperature increases to thrice the original
temperature respectively, if the original volume is Vo, then the new volume is,
A.2Vo B.Vo C.Vo/2 D.4Vo
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

𝑃𝑜𝑉𝑜 𝑃𝑓𝑉𝑓 𝑃𝑜𝑉𝑜 3𝑃𝑜𝑉𝑓 3𝑃𝑜𝑡𝑜 𝑉𝑓


= => = => = 𝑉𝑜 => 𝑽𝒇 = 𝑽𝒐
𝑡𝑜 𝑡𝑓 𝑡𝑜 3𝑡𝑜 3𝑃𝑜𝑡𝑜

10. What is the interest of P 8,600 after 4 years at 12 percent simple interest rate?
A.P 4,161 B.P 4,116 C.P 4,218 D.P 4,128

Solution:

𝐹 = 𝑃𝑖𝑛
𝐹 = (8,600)(12%)(4)
∴ 𝑭 = 𝑷 𝟒, 𝟏𝟐𝟖
11. First law of thermodynamics is also known as:
A. Conservation of Heat C. Conservation of Energy
B. Heat Transfer D. Utilization Energy

Explanation:
The first law, also known as Law of Conservation of Energy, states that
energy cannot be created or destroyed in an isolated system. The second law of
thermodynamics states that the entropy of any isolated system always
increases.The third law of thermodynamics states that the entropy of a system
approaches a constant value as the temperature approaches absolute zero.

12. Find the equivalent value of a 2μF and 4μF capacitors is connected in parallel and
in series with a 3μF capacitor.
A.3μF B. 2μF C.4μF D.5μ

Solution:

𝐶𝑝𝑎𝑟𝑎𝑙𝑙𝑒𝑙 = (2) + (4) = 6


(6)(3)
𝐶𝑡 = = 𝟐𝝁𝑭
(6) + (3)

13. How do you measure the voltage of a circuit element?


A. Voltmeter in series with the element
B. Voltmeter in parallel with the element
C. Ammeter in parallel with the element
D. Ammeter in series with the element

63
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Explanation:

A voltmeter is a device used to measure the potential difference “Between Two


Points”. In order to measure the potential between two points, we have NO WAY
around except to connect it in Parallel.

A voltmeter is a device of having high resistance. So, if we connect it in Series, it


would hinder the current flow in the circuit hence Open Circuit results. That’s why
we do not connect it in Series.

14. What is the most common reinforcement for polymer composites?


A. Boron B. Ceramic C. Graphite D. Glass Fiber

Explanation:

Glass fibers reinforced polymer composites have been prepared by various


manufacturing technology and are widely used for various applications. Nowadays, it
has been used in electronics, aviation and automobile application etc. Glass fibers are
having excellent properties like high strength, flexibility, stiffness and resistance to
chemical harm.

15. A process in pressure is constant?


A. Isobaric B, Isochoric C. Isometric D. Isothermal

Explanation:

An isobaric process is a thermodynamic process in which


the pressure remains constant. This is usually obtained by allowing the volume to
expand or contract in such a way to neutralize any pressure changes that would be
caused by heat transfer.

16. Section 40 of article IV of RA 7920 is the Penalty Clause, states that any person
who shall violate any of the provisions of this Act shall be guilty of misdemeanor and
shall, upon conviction, be sentenced to a fine of not less than __________ nor more
than P50, 000 or imprisonment for a period not less than 6 months nor more than 5
years or both at the discretion of the court.
A.P 10,000 B.P 15,000 C.P 25,000 D.P 30,000

17. According to RA 7920 the members of the BEE shall hold office for a term of
______ year from the date of appointment or until their successors shall have been
appointed and qualified.
A.6 B.4 C.3 D.5

18. Which doesn’t have electric charge?

64
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Proton B. Electron C. Molecule D. Neutron

Explanation:
The neutron is a subatomic particle, symbol n or n 0 , with no net electric
charge and a mass slightly larger than that of a proton.

19. May is declared as the electrical safety month virtue of ______ signed by Pres.
Benigno Aquino III last June 27, 2011 for the reason of informing the public of the real
reason of faulty electrical wiring.
A. RA 7920 C. Proclamation No. 183
B. Proclamation No. 193 D. RA 184

20. What is the maximum efficiency engine operated from a high temperature reservoir
to a low temperature reservoir?
A. Carnot B. Otto C. Ericson D. Bell-Coleman

Explanation:

The most efficient heat engine cycle is the Carnot Cycle, consisting of two
isothermal processes and two adiabatic processes. The Carnot cycle can be
thought of as the most efficient heat engine cycle allowed by physical laws.

21. EPIRA is RA 9136 which means_____________.


A. Electric Power Installation Reform Act
B. Energy Power Isolation Reform Act
C. Electric Power Industry Reform Act
D. Energy Power Institution Reliability Act

22. EPIRA is RA ____________.


A.184 B. 9136 C.9163 D.7920

23. A man pushes a 50-kg refrigerator at a distance of 15m. If the coefficient of friction
is 0.4, what is the work done by the man? Use g=9.8m/sec2.
A. 2490 J B. 7530 J C. 2940 J D. 7350 J

Solution:

𝐹𝑟 = 𝜇𝑁
𝐹𝑟 = 𝜇 𝑥 𝑚 𝑥 𝑔 𝑥 𝑑
𝑊 = (50)(9.8)(15)(0.4)
∴ 𝑾 = 𝟐𝟗𝟒𝟎 𝑱

65
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
24. A mass m is released at a height h, using conservation of energy, find the final
velocity of the mass as it hits the ground.
A. v=gh B. v=gh/2 C. v=√2gh D. v= √gh

Solution:

𝑉𝑓 2 = 𝑉𝑜2 + 2𝑔ℎ
𝑉0 = 0

∴ 𝑽𝒇 = √𝟐𝒈𝒉
25. A reservoir dam holds an 8.00-km2 lake behind it. Just behind the lake is 12.0m
deep. What is water pressure at a point 3.0m down from the lake’s surface?
A. 27 B. 29 C. 25 D. 24

Solution:

𝐴𝑠𝑠𝑢𝑚𝑒 𝑡ℎ𝑒 𝑝𝑟𝑒𝑠𝑠𝑢𝑟𝑒 𝑎𝑡 𝑡ℎ𝑒 𝑠𝑢𝑟𝑓𝑎𝑐𝑒 𝑖𝑠 1 𝑎𝑡𝑚


𝑇ℎ𝑒𝑟𝑒𝑓𝑜𝑟𝑒,
𝑃 = 𝑝𝑔ℎ
𝑃 = (1)(9.8)(3.0) = 𝟐𝟗. 𝟒 ≈ 𝟐𝟗
26. Conservation of _______________is used in collision, Explosion and the like.
A. mass B. energy C. momentum D. heat

Explanation:
In collision, we are using the law of conservation of momentum with the formula:

𝑚1 𝑣1 +𝑚2 𝑣2 = 𝑚1 𝑣′1 + 𝑚2 𝑣′2

27. The deflection beam is


A. directly proportional to the modulus of elasticity and moment of inertia.
B. inversely proportional to the modulus of elasticity and the length of the beam
cubed
C. inversely proportional to the modulus of elasticity and moment of inertia
D. directly proportional to the load imposed and inversely proportional to the length
squared

28. A copper column of annular cross-section has an outer diameter of 15 feet, and is
subjected to a force of 45 kips. The allowable compressive stress is 300 lbf/ft².
What should be the inner diameter?
A. 3.52 ft B. 5.03ft C. 4.59ft D. 5.83ft

Solution:

66
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

𝑃
𝑆=
𝐴
𝑃
𝑆=𝜋
2 2
4 (𝐷 − 𝑑 )
45,000
300 = 𝜋
(152 − 𝑑 2 )
4
∴ 𝒅 = 𝟓. 𝟖𝟑 𝒇𝒕
29. How many moles are there in 21.58 g of chloroform (CHCI3)
A. 0.1608 B. 0.1806 C. 5.5352 D.5.5252

Solution:

𝑀𝑊 𝑜𝑓 𝐶𝐻𝐶𝑙3 = 119.35 𝑔/𝑚𝑜𝑙


𝑔 21.58
𝑀𝑜𝑙𝑒𝑠 = = = 𝟎. 𝟏𝟖𝟎𝟖 ≈ 𝟎. 𝟏𝟖𝟎𝟔 𝒎𝒐𝒍𝒆𝒔
𝑀. 𝑤 119.35

30. What is the system program used to translate directly an assembly language to
machine language called
A. Compiler B. Debugger C. Interpreter D. Assembler

31. A machine is under consideration for investment. The cost of machine is P25,000.
Each of year it operates, the machine will generate a saving of P15,000. Given an
effective annual interest of 18%, what is the discount payback period, in year, on the
investment of the machine?
A. 1.566 B. 2.233 C. 2.155 D. 2.607

Solution:
(𝟏 + 𝐢)𝐧 − 𝟏
𝐏 = 𝐀( )
𝒊(𝟏 + 𝒊)𝒏
(1 + 18%)𝑛 − 1
25000 = 15000 ( )
18%(1 + 18%)𝑛
𝒏 = 𝟐. 𝟏𝟓𝟓 𝒚𝒓𝒔.
32. What best defines annuity?
A. a series of equal payments occurring at equal periods of time
B. First payment does not begin until some later date.
C. value of the stock as stated on the stock certificate.

67
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
D. difference between the present value and the worth of money at some time in the
future.

33. What interest rate compounded monthly in equivalent to an invest rate of 9%


compounded quarterly?
A. 9.10% B. 9% C. 9.31% D. 8.93%

Solution:

𝐸𝑅𝐼 = 𝐸𝑅𝐼
𝑟 𝑚 𝑟 𝑚
(1 + ) = (1 + )
𝑚 𝑚
𝑟 12 9% 4
(1 + ) = (1 + )
12 4
𝒓 = 𝟎. 𝟎𝟖𝟗𝟑 𝒙 𝟏𝟎𝟎 = 𝟖. 𝟗𝟑%

34. A 20-m long extension cord made of 35 mm² THWG conductor has across-section of
0.033 cm². What is the resistance of the cord? (p= 1.7x10 raise to -8 Ω-m)
A. 0.281 Ω B. 0.218 Ω C. 0.130 Ω D. 0.103 Ω

Solution:

𝑝𝑙 1𝑚
𝑅= 𝐴 = 0.033𝑐𝑚2 𝑥 1002 𝑐𝑚 = 3.3 𝑥10−6 𝑚
𝐴

(1.7𝑥10−8 )(20)
𝑅= = 𝟎. 𝟏𝟎𝟑Ω
3.3𝑥10−6

35. A bike worth P10, 000 is discounted now at 10%. Four months later and bike is sold
with 15% discount. How much the bike sold?
A. P 9,000 B. P 8,000 C. P 7,650 D.8, 750

Solution:

𝑃 = 10,000 (0.10) = 9,000


𝑃 = 9,000 (0.15) = 1350
𝑃 = 9000 − 1350 = 𝑷 𝟕, 𝟔𝟓𝟎
36. Accumulate P6, 000 at the end of 12years at the interest rate of 10%.
A. P 1,931.34 B. P18, 830.57
C. 1,911.78 D. P18, 635.09

68
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝐹 = 𝑃 (1 + 𝑖)𝑛
𝐹 = 6,000 (1 + 0.1)12
∴ 𝑭 = 𝑷 𝟏𝟖, 𝟖𝟑𝟎. 𝟓𝟕
37. Find the value P100 at the end of 2years at an interest rate of 8% compounded
quarterly.
A. 116.64 B. 116.99 C. 117.17 D. 117.29

Solution:

𝐹 = 𝑃 (1 + 𝑖)𝑛
8% 2(4)
𝐹 = 100 (1 + )
4
∴ 𝑭 = 𝟏𝟏𝟕. 𝟏𝟔𝟓

38. Mr. Cruz borrowed P12, 000 at an interest rate of 10% per annum. Find the lump
sum that he will pay at the end of 4 years?
A. P 17,569.57 B. 8,196.16 C. 19,326.12 D. 7,451.06

Solution:

𝐹 = 𝑃 (1 + 𝑖)𝑛
𝐹 = 12,000(1 + 10%)4 = 𝑷 𝟏𝟕, 𝟓𝟔𝟗. 𝟐
39. Find the initial deposit if you want to accumulate P12, 000 at the end of 6years with
an interest rate of 12%.
A. P 6,079.57 B. 6, 309.12
C. 2,918.71 D. 3,328.92

Solution:

𝐹 = 𝑃 (1 + 𝑖)𝑛
𝐹 = 12,000 (1 + 12%)6 = 𝑷 𝟔, 𝟎𝟕𝟗. 𝟓𝟕
40. A truck accelerate from rest 120kph in 2 s. Find the average acceleration in m/s².
A. 16.67 B. 60 C. 33.33 D. 8.33

Solution:

1 𝑚
120,000𝑥 = 13.3333
3600 𝑠𝑒𝑐𝑠

69
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑉𝑜 − 𝑉𝑓 13.333
𝑎= = = 𝟏𝟔. 𝟔𝟔𝟕 𝒎/𝒔𝟐
𝑡 2𝑠𝑒𝑐
41. A side (2 in) of a square is loaded in tension by force of 12kips. Determine the
normal stress in ksi in the rate of interest.
A. 5.5 B. 6 C. 2.6 D. 3

Solution:

𝑃
𝑆=
𝐴
12
𝑆= = 𝟑𝒌𝒔𝒊
2𝑥2
42. A price tag of P1, 450 is paid in 70 days, but if paid within 35 days, it will have 5%
discount. Find the rate of interest.
A. 52 percent B. 54 percent C. 57 percent D. 36 percent

Solution:
𝐷𝑖𝑠𝑐𝑜𝑢𝑛𝑡𝑒𝑑 = 1450 − 1450(0.05) = 𝑃 1377.5
𝐼 = 𝑃𝑖𝑛
35
72.5 = 1377.5(𝑖) ( )
365
𝒊 = 𝟎. 𝟓𝟒 𝒐𝒓 𝟓𝟒%
43. A price tag of P1, 450 is paid in 70days, but if paid within 35days, it will have a 5%
discount. Find the rate of interest.
A. 52 percent B. 54 percent C. 57 percent D. 36 percent

Solution:
𝐷𝑖𝑠𝑐𝑜𝑢𝑛𝑡𝑒𝑑 = 1450 − 1450(0.05) = 𝑃 1377.5
𝐼 = 𝑃𝑖𝑛
35
72.5 = 1377.5(𝑖) ( )
365
𝒊 = 𝟎. 𝟓𝟒 𝒐𝒓 𝟓𝟒%
44. The change that the system undergoes from one equilibrium state to another is
known as ____________.
A. path B. process C. enthalpy change D. Entropy change

70
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
45. What is the entropy of pure substance at the temperature of absolute zero?
A. unity B. zero C. infinity D. undefined

46. Find the amount of P30, 000 at 15% per annum after 2years.
A. P39, 675 B. P 22,685 C. P 34,500 D. 30,000

Solution:

𝐹 = 𝑃 (1 + 𝑖)𝑛
𝐹 = 30,000 ( 1 + 15%)2 = 𝑷 𝟑𝟗, 𝟔𝟕𝟓
47. Find the amount of P30, 000 at 6% simple interest after 5 years.
A. P39, 000 B. P40, 000 C. P41, 000 D.P42, 000

Solution:

𝐹 = 𝑃(1 + 𝑖𝑛)

𝐹 = 30,000(1 + (6%)(5)) = P 39,000

48. What is the amount of heat needed to turn 1kg of substance at its melting point from
the solid to the liquid state?
A. Heat of fusion B. Heat of vaporization
C. Heat of condensation D. Heat of fission

49. What is the value of 11101110 base 2 to base 8?


A. 356 B. 365 C. 653 D. 635

Solution:

11 101 1102 = 3 5 6 8
50. A sports car is traveling at 50kph when it applies full brakes. It travels 15 ft. before
coming to a full stop. If it now travels at 150kph and applies brakes the same way,
how far does it travel before it stop?
A. 15ft B. 26ft C. 45ft D. 135 ft.

Solution:

50𝑘𝑚 1000𝑚 3.28𝑓𝑡 𝑓𝑡


𝑥 𝑥 = 164,000
ℎ𝑟 1𝑘𝑚 1𝑚 ℎ𝑟

71
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
150𝑘𝑚 1000𝑚 3.28𝑓𝑡 𝑓𝑡
𝑥 𝑥 = 492,000
ℎ𝑟 1𝑘𝑚 1𝑚 ℎ𝑟
𝑉 2 = 𝑉𝑜2 − 2𝑎𝑆
02 = (164)2 − 2(𝑎)(15)
896.53𝑥103 𝑓𝑡
𝑎=
ℎ𝑟 2
𝑉 = 𝑉𝑜 − 𝑎𝑡
0 = 492 − (896.53)(t)
𝑡 = 0.549 ℎ𝑟
1 1
𝑆 = 𝑉𝑜𝑡 − (𝑎)(𝑡)2 = (492)(0.549) − (896.53)(0.549)2
2 2
𝑺 = 𝟏𝟑𝟓 𝒇𝒕
51. The center of gravity of a log, 10 ft. long and weighing 100 lb., is 4 ft. from one end
of the log. It is to be carried by two men. If one is at the heavy end, how far from the
other end does the second man have to hold the log if each is to carry 50 lb.?
A. 2 ft. B. 4 ft. C. 5 ft. D. 6 ft.

Solution:

4 (100) – 50 (10 – x) = 0
400 – 500 + 50x = 0
50x = 100
X= 2ft
52. For rectangular section of breadth “b” and depth “h” the section modulus is given by:
A. z = bh3/12 B. z = bh3/6 C. z = bh2/12 D. z = bh2/6

53. Ideal fluid has:


A. no surface tension
B. no surface tension, no viscosity
C. no surface tension, no viscosity and no compressibility
D. surface tension, viscosity and compressibility

54. A thin hollow sphere of radius 10 in. and thickness 0.1 in. is subjected to an internal
pressure of 100 psig. The maximum normal stress on an element of the sphere is
A. 5,000 psi B. 10,000 psi C. 25,000 psi D. 20,000 psi

Solution:

72
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
S = PD / 2T
S= (100) (10) / 2(0.1) = 5000 psi
55. The area of the shear diagram of a beam between any two points on the beam is
equal to the
A. Change in shear between the two points
B.Total shear beyond the two points
C. Average moment between two points
D. Change in moment between two points

56. Carbon dioxide “snow” from a fire extinguisher puts out a fire because it
A. lowers the kindling temperature of the material
B. displaces the supply of oxygen
C. raises the kindling temperature of the material
D. cools the material below its kindling temperature

57. The rocks generally used for roofing, is


A. granite B. basalt C. slate D. trap

58. During a refrigeration cycle, heat is rejected in a:


A. evaporator B. condenser
C. compressor D. expansion valve

59. A 20-g piece of aluminum (c = 0.21 cal/g-deg C) at 90 deg C is dropped into a cavity
in a large block of ice at 0 deg C. How much ice does the aluminum melt?
A. 6.3 g B. 3.6 g C. 7.4 g D. 4.7 g

Solution:
𝑄 = 𝑚𝐶𝛥𝑇 = (20) (0.21) (90 − 0) = 378
𝑄 378
𝑄 = 𝑚𝐿; 𝑚 = = = 𝟒. 𝟕𝟐𝟓 𝒈
𝐿 80

60. Stainless steel resists corrosion due to


A. carbon B. sulfur C. chromium D. vanadium

61. A baseball is thrown with an initial velocity of 100 m/s at an angle of 30 degrees
above the horizontal. How far from the throwing point will the baseball attain its
original level?
A. 799 m B. 977 m C. 884 m D. 848 m

Solution:

Vo = 100 m/s; Ɵ = 30

73
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Vo 2 sin 2 Ɵ (100)2 sin(2 x 30)
R= = = 884 m
g 9.81

62. A solid steel shaft 8 ft long is to transmit a torque of 20,000 ft-lb. The shear modulus
of the material is 12 x 106 psi, and the allowable stress is 10,000 psi. Compute the
angle of twist between the two ends of the shaft
A.1.39 degrees B. 1.93 degrees C. 1.48 degrees D. 1.84 degrees

Solution:

16T 1.44x106 lb 16(20,000)


S= ; =
πD3 ft 2 π(D)4
D = 0.4135 ft
πD4 π(0.4135)4
J= = = 2.87x10−3
32 32
TL (20,000)(8)
θ= =
JG (2.87x10−3 )(1.728x109 )
𝛉 = 𝟏. 𝟖𝟒𝟖 ≅ 𝟏. 𝟖𝟒

63. The density of nitrogen is 1.25 kg/m3 at STP. Determine the density of nitrogen at 42
deg C and 730 mm of mercury.
A. 1.04 kg/m3 B. 1.40 kg/m3 C. 0.96 kg/m3 D. 0.69 kg/m3

Solution:

P1 P2 m
=
ρ1 T1 ρ2 T1

760 730
=
1.25(273) ρ2 (315)

𝛒𝟐 = 𝟏. 𝟎𝟒 𝐤𝐠/𝐦𝟑

64. Air having an initial pressure of 1 atm, temperature of 80 deg F, and volume of 28.6
cu. ft. is compressed isentropically in a nonflow process to a final pressure of 120
psia. The final volume in cu. ft. is nearest to
A. 15.5 B. 12.1 C. 6.2 D. 3.7

Solution:

P1 = 1 atm

74
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
1 𝑎𝑡𝑚
𝑃2 = 120 𝑝𝑠𝑖𝑎 𝑥 ( ) = 8.1633 𝑎𝑡𝑚
14.7 𝑝𝑠𝑖𝑎
V1 = 28.6 ft³
𝑃1 𝑉1𝑘 = 𝑃2 𝑉2𝑘
(1)(28.6) 1.4 = (8.1633)(𝑉2) 1.4
𝑽𝒔 = 𝟔. 𝟐 𝒄𝒖. 𝒇𝒕

65. For churches, a general lighting load of _______ VA/m2 shall be used.
A. 12 B. 4 C. 8 D. 2

66. The number 1010 base 2 is equivalent to decimal number _________.


A. 6 B. 10 C. 8 D. 12

67. Absolute reference in a spreadsheet is used by inserting a ________ sign before the
column and row. This is used for data reference in another cell.
A. period B. dollar C. semi-column D. hyphen

68. A pressure gage measure 20 kPa vacuum in a system. What is the absolute
pressure, if the atmospheric pressure is 101 kPa?
A. 121 kPa B. 51 kPa C. 81 kPa D. 91 kPa

Solution:
𝑃𝑔𝑎𝑔𝑒𝑣𝑎𝑐𝑢𝑢𝑚 = −20 𝑘𝑃𝑎
𝑃𝑎𝑡𝑚 = 101 𝑘𝑃𝑎
𝑃𝑎𝑏𝑠 = 𝑃𝑔𝑎𝑔𝑒 + 𝑃𝑎𝑡𝑚 = 101 + (−20) = 𝟖𝟏𝒌𝑷𝒂

69. Earth’s surface is part of the


A. asthenosphere B. Lithosphere
C. benthosphere D. troposphere

70. This refers to energy-consuming equipment including motors, heaters, furnaces,


light sources and other devices which utilize electric energy, for any purpose.
A. Industrial Plant C. Processing Plant
B. Utilization Equipment D. Transformer

71. An aircraft in level flight is said to make a standard turn when it makes a complete
turn in two minutes. What is the banking angle in standard turn if velocity is 400 fps?
A. 24 deg B. 33 deg C. 48 deg D. 55 deg

Solution:

2𝜋 2𝜋 𝜋
𝜔= = =
𝑇 2min(60seconds) 60

75
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑣 400
r= = 𝜋 = 7639.44 𝑓𝑡
𝜔
60
𝜔2 𝑟
𝜃 = 𝑡𝑎𝑛-1( ) = 𝟑𝟑 𝒅𝒆𝒈
𝑔
72. A pilot tube is used to measure:
A. discharge B. velocity of fluid
C. total energy of the fluid D. all of these

73. The discharge through a 75-mm diameter orifice at the bottom of a large tank was
measured be 1734 liters in 1 minute. If the head over the orifice remains constant at
5.5m, compute the coefficient of discharge.
A. 0.84 B. 0.63 C. 0.78 D. 0.98

Solution:
𝑄 = 𝐶𝑑𝐴√2𝑔ℎ

𝑙 1𝑚3 1𝑚𝑖𝑛
𝑄 (1734 )( 3 )( )
𝑚𝑖𝑛𝑢𝑡𝑒 10 𝑙 60𝑠𝑒𝑐𝑜𝑛𝑑𝑠
𝐶𝑑 = = 𝜋 75
𝐴√2𝑔ℎ ( 4 )(1000)²√(2)(9.81)(5.5)
𝑪𝒅 = 𝟎. 𝟔𝟑

74. An aluminum rod of initial length 10 cm is stretched to a length of 15 cm. Later, the
same rod is compressed to 12 cm. The true strain is nearest
A. 0.75 B. 0.16 C. 0.18 D. 0.20

Solution:

𝐿𝑖 12
Ԑ = ln( ) = ln ( ) = 𝟎. 𝟏𝟖
𝐿𝑜 10

75. When a pressure of 2.0 MPA is applied to a sample of kerosene, it contracts by 0.15
percent. The bulk modulus of kerosene is
A. 1.6 GPA B. 1.8 GPA C. 1.3 GPA D. 1.1 GPA

Solution:

𝛥𝑃 (2)(106)
Mk = = = 𝟏. 𝟑𝑮𝑷𝑨
𝛥𝑉/𝑉 (0.15)

76. Which group of the periodic table is known as the alkali metals?
A. Group 1 B. Group 2 C. Group 3 D. Group 4

77. Which law states “Entropy of all perfect crystalline solids is zero at absolute zero
temperature”?

76
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Zeroth Law of thermodynamics C. Second Law of thermodynamics
B. First Law of thermodynamics D. Third Law of thermodynamics

78. In galvanized iron, a lining on iron is provided with:


A. Sn B. Zn C. Cu D. Al

79. A metal cube, 2.00 cm on each side, has a density of 6600 kg/m³. Find its apparent
mass when it is totally submerged in water.
A.58.2 g B. 52.8 g C. 48.4 g D. 44.8 g

Solution:
V = edge3 = (0.02)3 = 0.000008m3
W = ρgV = (6,600)(9.81)(0.000008) = 0.517968 N
W’ = ρ’gV = (1,000)(9.81)(0.000008) = 0.07848 N
App. W = 0.517968 – 0.07848 = 0.439 N
𝐴𝑝𝑝 𝑊
App mass = = 0.0484 𝑘𝑔 = 𝟒𝟖. 𝟒𝒈
𝑔

80. Determine the moment of inertia of an equilateral triangle 6 in on a side about an


axis through its side.
A. 70.1 in ⁴ B. 23.4 in ⁴ C. 35 in ⁴ D. 46.8 in ⁴

Solution:

𝑏ℎ³ 6(3√3)³
Ix = = = 𝟕𝟎. 𝟏𝟒𝟖 𝒊𝒏4
12 12

81. (U + PV) is a quantity called


A. Flow energy B. shaft work C. entropy D. enthalpy

82. A 3HP refrigerator or heat pump operates between 0 deg F and 100 deg F. The
maximum theoretical heat that can be transferred from the cold reservoir is nearest 0
A.7,600 BTU/hr B. 13,000 BTU/hr C. 23,000 BTU/hr D.35,000 BTU/h

83. A department store changes one and one-half percent interest per month on credit
purchases. This is equivalent to a nominal annual interest rate of
A. 15 percent B. 18 percent C. 19.6 percent D. 21 percent

Solution:
𝑟
𝑖= 𝑟 = 0.18 𝑥 100
𝑚

77
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑟 = 𝑖𝑚
𝑟 = (0.015)(12)
𝒓 = 𝟏𝟖%
84. The element that is practically insoluble in solid is known as
A. Lead B. Brass C. Boron D. Neon

85. The present worth of an obligation of P100, 000 due in 10 years if money is worth 9
percent is nearest to
A. P100,000 B. P90,000 C. P75,000 D. P45,000

Solution:

𝑃 = 𝐹 (1 + 𝑖)−𝑛
𝑃 = 100,000 (1 + 0.09)−10
𝑷 = 𝟒𝟐, 𝟐𝟒𝟏. 𝟎𝟖 ~ 𝟒𝟓, 𝟎𝟎𝟎
86. A company deposits P1, 000,000 every year for ten years in a bank. The
company makes no deposits during subsequent five years. If the bank pays 8
percent interest, the amount in the account at the end of 15 years is nearest to
A. P10,000,000 B. P15,000,000 C. P21,200,000 D. P 25,200,000

Solution:

(1+𝑖 )𝑛 −1
𝐹 =𝐴[ ] 𝐹 = 𝑃 (1 + 𝑖𝑛)
𝑖

(1+0.08)10 −1
𝐹 = 1𝑀 [ ] 𝐹 = 14.49 𝑀 [1 + (0.08)(5) ]
0.08

𝐹 = 14.49 𝑀 𝑭 = 𝟐𝟎. 𝟐𝟖 𝑴 ~ 𝟐𝟏. 𝟐 𝑴

87. What do you call materials that do not conduct electric current?
A. Conductor B. Insulator C. Semi-conductor D. Intrinsic Material

88. A branch of physical science which deals with the state of rest or motion of bodies
under the action of forces.
A. Mechanics B. Kinetics C. Kinematics D. Statics

89. A wire or cable carrying electric current, supported by poles, tower of other
structures, but not including vertical or lateral connecting wires.

78
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Transmission Line C. Conductor
B. Line Conductor D. Lateral Conductor

90. What refers to the value of an asset which is disinterested third party, different from
the buyer and seller, will determine in order to establish a price acceptable to both
parties?
A. Book value B. Market value C. Fair value D. Franchise value

91. A general term covering on assembly or assemblies of devices for switching,


interrupting, controlling, metering of electric power.
A. Enclosure B. Switchgear
C. Switchboard D. Panel board

92. In air conditioning of aircrafts, using air as refrigerant, the cycle used is:
A. Reversed Joule Cycle C. Reverse Brayton Cycle
B. Reversed Carnot Cycle D. Reverse Otto Cycle

93. What present sum would need to be put in savings account now to provide P10, 000
annual withdrawals for the next 50 years, if interest is 6 percent?
A. P175.620 B. P157,620 C. P262,490 D. P226,490

Solution:

1 1
F = A ((1 + i) n − = 10,000 ((1+0.06) 50 – ) = P2, 903,359.046
𝑖 0.06
𝐹 2,903,359.046
P= = = P157,620
(1+𝑖)𝑛 (1+0.06)50

94. A 600N object is to be given an acceleration of 0.70m/s 2. How large an unbalanced


force must act upon it?
A. 43 N B. 34 N C. 93 N D. 39N

Solution:

𝑤 600
F= 𝑥𝑎= 𝑥 0.70 = 43N
𝑔 9.81

95. The 160 lb. man stands on a spring scale resting on the floor of an elevator. Find the
scale reading if the elevator accelerates upward at 8ft/s2
A. 160 lb. B. 130 lb. C. 220 lb. D. 200 lb.

Solution:

79
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑚 160
𝑥 (𝑎 + 𝑔) = (32.2 + 8)
𝑔 32.2

= 𝟏𝟗𝟗. 𝟕𝟓 ≈ 𝟐𝟎𝟎𝐥𝐛𝐬.
96. Find the elongation in cm of a straight bar 12m long due to its own weight if hung.
The value of modulus of elasticity of the material is unknown. However, it is known
that the modulus of rigidity is 88 GPA. Poisson’s ratio is 0.25 and density of 0.0086
kg/cm³.
A. 0.0266 cm B. 0.0662 cm
C. 0.00266 cm D. 0.00662 cm

Solution:

𝑝𝑔𝐿2
δ= 2𝐸

0086𝑘𝑔 1003 𝑐𝑚
𝑥 = 8600𝑘𝑔/𝑚3
𝑐𝑚3 1𝑚3

𝐸 = 2𝐺(1 + 𝜇)
𝐸 = 2(88𝑥109 )(1 + 0.25)
𝐸 = 2.2𝑥1011
(8600)(9.81)(12)2
δ=
2(2.2𝑥1011 )
𝛅 = 𝟐. 𝟕𝟔𝟏𝟎𝟔𝐱𝟏𝟎−𝟓 𝒙 𝟏𝟎𝟎 = 𝟎. 𝟎𝟎𝟐𝟕𝟔 ≈ 𝟎. 𝟎𝟎𝟐𝟔𝟔𝒄𝒎

97. The second period contains how many elements


A. 2 B. 4 C. 6 D. 8

98. Mercury cannot wet a glass tube. That is due to:


A. Cohesion B. adhesion C. surface tension D. viscosity

99. Water falling from a height of 120 ft. at the rate of 100 drives a turbine that is directly
connected to an electric generator. The generator rotates at 120 rpm. If the total
resisting torque due to friction and other losses is 250lb-ft and the water leaves the
turbine blades with a velocity of 15fps, the horsepower developed by the generator
is nearest to
A. 207 B.214 C. 221 D. 228

100. How many atoms are there per unit cell of a BCC structure?
A. 1 B.2 C. 3 D. 4

80
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM MARCH 2016

19. Which of the following is Charle’s law?


1 P1 P2 𝐕
A. V = k x𝑃 B. T1 = T2 C. PV = mRT D. 𝐓= k

20. Which of the following is the ideal gas law?


V P1 P2 1
𝐴. T = k B. T1 = T2 C. PV = mRT D. V = k x𝑃

21. FTTH means _________.


A. Flexible To The House C. Fiber To The House
B.FlexibleTo The Home D. Fiber To The House

22. A device used in Thermal power plant to reduce air pollution?


A. Pulverizer B. Precipitator C. Disulfurizer D. Chimney

23. What are elements that have properties intermediate between metals and
nonmetals?
A. Gases B. Solids C. Metalloids D. Liquids

24. What is the primary purpose of PEC?


A. to serve as guide for the untrained personnel
B. is to conserve electrical energy
C. is the practical safeguarding of persons and property
D.to serve as manual guide for design

25. The primary winding of a step-up transformer 240/6000 V has 150 turns. The
secondary winding has many turns?
A. 3750 B. 4000 C. 3500 D. 4250

Solution:
(150)(6000)
Secondary Winding = 240

𝑆𝑒𝑐𝑜𝑛𝑑𝑎𝑟𝑦 𝑊𝑖𝑛𝑑𝑖𝑛𝑔 = 𝟑𝟕𝟓𝟎 𝒕𝒖𝒓𝒏𝒔

26. What is the effective annual interest rate on a loan if the nominal interest rate is 12
percent per compounded quarterly?
A. 11.75 percent C. 12.25 percent
B. 12 percent D. 12.55 percent
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝑟
ER = (1 + 𝑚)𝑚 − 1

0.12 4
ER = (1 + ) −1
4

ER = 0.1255 x 100
𝑬𝑹 = 𝟏𝟐. 𝟓𝟓%

27. An investment of $350,000 in made to be followed by payments of $200,000 each


year for three years is the annual rate of return on investment for this payment?
A. 15 percent B. 32.7 percent C. 41.7 percent D. 57.1 percent

Solution:
(1+𝑖)𝑛
P =𝐴 [𝑖( 1+𝑖)𝑛 ]

(1+𝑖)3
350000 = 200000 [𝑖( 1+𝑖)3 ]

𝑖 = 0.327 𝑥 100

𝒊 = 𝟑𝟐. 𝟕%

28. Vertical clearance from ground. Service-drop conductors where not in excess of 600
volts, nominal shall the minimum clearance from final grade of _______ over
residential property and driveways, and commercial areas not subject to truck traffic
where the voltage does not exceed 300 volts to ground.
A. 3100 mm B. 3700 mm C. 4600 mm D. 5500 mm

Solution:

Not exceed 300V to ground


From NEC 3.7m (12)
3.7m × 1000mm
= 1m

∴ 𝟑𝟕𝟎𝟎𝒎𝒎
29. When the circuit breakers are installed in enclosed switchboards, they are usually
derated to a percentage. What is this percentage?
A. 60 percent B. 50 percent C. 80 percent D. 70 percent

Solution:
82
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Circuit Breaker = 80% standard allow extra 25% capacity for


Continuous load to make 100%.

30. A user has to download 800 KB file using 28.8 kmodem. How long will the file be
downloaded?
A. 3.2 min B. 3.6 min C. 3.7 min D. 3.9 min

Solution:

28.8 kmodem = 28.8 kbps= 3.6 kBps


800kB
T =3.6kBps
= 222.222𝑠𝑒𝑐 = 𝟑. 𝟕 𝒎𝒊𝒏

31. Vinegar is solution of H2O and what acid?


A. sulfuric acid B. acetic acid C. phosphoric acid D. nitric acid

32. What is the other term for storing data in a memory?


A. reading B. loading C. memorizing D. writing

33. What is the common input device?


A. speaker B. keyboard C. mouse D. LCD

34. Subtract (1010) base 2 from (20) base 8. Express the answer in decimal
A. 7 B. 5 C. 4 D. 6

Solution:

20 base 8 = 10000
10000 – 1010 = 0 / 1 / 1 /0
84 2 1 = 6 in decimal
35. The ability of the surface of material to reflect light is called
A. creep B. malleability C. lustre D. ductility

36. The mole is a basic unit of measurement in chemistry. Which of the following is not
equal so or the same as one mole of the substance indicated?
A. 22.4 liters of nitrogen gas as STP
B. 6.02x1023 oxygen molecules

83
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
C. 1 g of hydrogen atoms
D. 16 g of oxygen molecules

37. The plates of a parallel-plate capacitor are 10 cm square and 1.0 mm apart. Find its
capacitance
A. 78 pF B. 98 pF C. 87 pF D. 89 pF

Solution:

C=kA/D
K = 8.854 x10−12
A =10x10−2m
D = 1.0x10−3
(8.854x10^−12)(10x10^−2)
C= (1.0x10−3)

𝑪 = 𝟖𝟗𝒑𝑭

38. The process of outsmarting the search engine.


A. Google Fooling C. Search Engine Optimization
B. Rank Enhancement D. Search Engine Hacking

39. A particle is moving with its acceleration parallel to velocity. What is the direction of
the particles?
A. circle B. linear C. parabolic D. never

40. Find the depth of the water having a pressure of 1.01x105kPa at the bottom
(pH2O = 1000 kg/cu. m.)
A. 12,400 m B. 9,800 m C. 10,300 m D. 11,200 m

Solution:

= (1.01𝑥105 )𝑥103
ℎ = = 𝟏𝟎, 𝟑𝟎𝟔. 𝟏𝟐𝟐 𝒎
(1000)(9.8)

41. A device produces 37.5 J per cycle. There is one power stroke per cycle. Calculate
the power output device is run at 45 rpm?
A. 14.063 W B. 4.69 W C. 27.56 W D. 28.125 W

Solution:

84
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑃 = 37.5 (45)(1/60)
∴ 𝑷 = 𝟐𝟖. 𝟏𝟐𝟓 𝑾
42. The velocity of the object changes from 30 mph to 90 mph. Find the ratio of the
kinetic energy.
A. 9 B. √3 C. 6 D. √6

Solution:
1
KE = 𝑚𝑣 2
2

Assuming a constant mass of 1kg


1
KE1 = (2)(1kg)(30)2 = 450
1
KE2 = (2)(1kg)(90)2 = 4050

4050
𝑅𝑎𝑡𝑖𝑜 𝑜𝑓 𝑘𝑖𝑛𝑒𝑡𝑖𝑐 𝑒𝑛𝑒𝑟𝑔𝑦 𝑜𝑓 𝑉1 𝑎𝑛𝑑 𝑉2 = 𝐾𝐸2 /𝐾𝐸1 = = 𝟗
450
43. What do you call the kind of wire used to bind the service drop to the service point?
A. Joint wire B. Splice wire C. Tie wire D. None of these

44. What device used to measure fluid velocity as well the velocity of fluid inside a
pipe?
A. Barometer B. Pivot Tube C. Hydrometer D. Thermometer

45. The board of Electrical Engineering is composed of one chairman and how many
members?
A. 2 B. 3 C. 4 D. 5

46. The term “Thermodynamics” comes from the Greek words “Therme” and
“Dynamis” which means?
A. heat, power B. heat, motion C. heat, transfer D. heat, energy
47. An object moving in a circle at a constant speed has an acceleration that is
A. in the direction of motion C. away from the center of the circle
B. toward the center of the circle D. zero

48. Which of the following is the basic equation of accounting?


A. Assets = Liability + owner’s equity
B. Liability = Assets + owner’s equity

85
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
C. Owner’s equity = Assets + liability
D. Owner’s equit = Liability + Assets

49. You are standing on a bathroom scale in an elevator, in which of these situation
must the same as when the elevator is at rest?
A. Moving up at constant speed
B. Moving up with increasing speed
C. Moving down with increasing speed
D. in free fall (after the elevator cable has snapped)

50. A steel rod of circular cross-section of diameter d = 1.25 in. is to carry a tensile load
P = 5 maximum sheering stress in the rod.
A. 4.07 ksi B. 2.04 ksi C. 5.43 ksi D. 1.27
ksi
Solution:

𝑃 𝑃
S= =𝜋
𝐴 (𝑑)2
4

5
S= 𝜋
(𝑑)2
4

𝑆 = 𝟒. 𝟎𝟕 𝒌𝒔𝒊

51. What is another term for “acid-test ratio”?


A. Quick Ratio C. Current Ratio
B. Price-earnings Ratio D. Profit margin ratio

52. What is the force per unit area?


A. work B. energy C. pressure D.power

53. What principle behind in a hydraulic brake of the automobile?


A. Archimedes Principle C. Stoke’s Principle
B. Bernoulli’s Principle D. Pascal’s Principle

54. The measure of randomness or disorder is known as the ________.


A. entropy B. enthalpy C. energy D. power

55. Applicants for registered master electrical’s examination must be at least _____
years of age.

86
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 18 B. 19 C. 20 D. 21

56. Which of the following is not a part of the requirements to take free examination?
A. he is citizen of the Philippines
B. He is at least twenty-one (21) years of age
C. He is good reputation with low morale values
D. He has not been finally convicted by the court of an offense involving moral
turpitude

57. If you leave the refrigerator door open and the refrigerator runs continuously, the
kitchen will
A. get cooler C. get warmer
B. remain as the same temperature D. get warmer or colder

58. If a refrigerator uses 1.5 KJ to cool a 1 KJ input. What was the heat transferred to
the kitchen?
A. 1 kJ B. 2 kJ C. 0.5 kJ D. 2.5 Kj

Solution:

∆U=U2-U1
∆U=1.5KJ -1KJ
∆𝑼 = 𝟎. 𝟓 𝑲𝑱
59. Find the amount of money you have to deposit in order to accumulate P1,500 per
quarter for interest rate of 12% compounded quarterly.
A. P4,958.71 B. P4,598.71 C. P34,672.16 D. P36,

Solution:

N= 10 years
0.12 −10(4)
1−(1+ )
4
P=1500 | 0.12 |
4

∴ 𝑷 = 𝑷 𝟑𝟒, 𝟔𝟕𝟐. 𝟏𝟔

60. Find the equivalent annual rate of interest of 8% compounded quarterly.


A. 8.42% B. 8.24% C. 6.46% D. 6.64%

Solution:

87
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑟 𝑚 𝑟
(1 + ) − 1 = (1 + )𝑚 − 1
𝑚 𝑚
𝑟 0.88 4
(1 + )1 − 1 = (1 + ) −1
1 4
1 + r = 1.0824

r = 1.0824 – 1

r = 0.0824 x 100

𝒓 = 𝟖. 𝟐𝟒%

61. Find the equivalent quarter interest of 8.5% annual rate.


A. 8.42% B. 8.24% C. 2.12% D. 2.06%

Solution:
𝑟 𝑟
(1 + 𝑚)𝑚 − 1 = (1 + 𝑚)𝑚 − 1

𝑟 0.085 1
(1 + 1)4 − 1 = (1 + ) −1
1

𝑟 4
(1 + 4) = √1.085

r = 4 (1.021 – 1)
r = 0.0824 x 100
𝒓 = 𝟖. 𝟐𝟒%

62. A motorcycle is moving in a semi-circular hill with 10-m radius of curvature. What
should be the velocity to prevent airbourne?
A. 10.2 m/sec B. 6.3 m/sec C. 8.7 m/sec D. 9.9 m/sec

63. Process of posting latitude and longitude to picture and images.


A. Podcasting B. Geotagging C. Flagging D. Posting

64. An escalator raises a 100 kg bucket of sand 10 m in 1 minute. Determine the total
amount during the process.
A. 9800 B. 32200 C. 102 D. 98

Solution:

88
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Energy = Force X distance
m
(100 kg) (9.8 𝑠2 ) (10 m)

∴ 𝟗𝟖𝟎𝟎 𝑵 − 𝒎 𝒐𝒓 𝑱𝒐𝒖𝒍𝒆

65. A price tag of P1450 is paid in 70 days, but if paid within 35 days it will have a 5
percent discount. What is the rate of interest?
A. 52 percent B. 15 percent C. 54 percent D. 36 percent

Solution:

i= d/1-d
(5%)
i= (1−5%)

𝒊 = 𝟓𝟐%

66. An ice with mass of 0.9 kg is freely floating in water. Find the buoyant force
experience by the
A. 7.8 N B. 8.82 N C. 10.2 N D. 9.64 N

Solution:

Fb = pgV
Fb = mg
m
Fb = (0.9) (9.8 𝑠2 )
Fb = 8.82

67. The process of detecting. Locating and correcting logic errors in a program
A. compiling B. reading C. deteting D. debugging

68. In any collision, which of the following is conserved.


A. kinetic energy B. velocity C. momentum D. potential

69. A manometer is used to measure?


A. positive pressure C. atmospheric pressure
B. negative pressure D. positive as well as negative pressure

70. The maximum bending moment in a cantilever of span L carrying a U.D.L of


intensity w per unit length is.
A. wL2 B. wL2/2 C. 2 wL2 D. wL2/8

89
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

71. The process of mixing clay, water and other ingredients to make brick is known as
A. kneading B. moulding C. pugging D. dying

72. Jeff regularly buys 16 gallons of gas, but the gas station has installed new pumps
that are measured in liters. How many liters of gas (rounded off to a whole number)
should he ask for?
A. 95 B. 59 C. 86 D. 68

Solution:
16gal x 3.785lit
= 1gal

=60.56
∴ 𝟓𝟗 𝒍𝒊𝒕.
73. One Newton is equivalent to
A. 106 dyne B. 107 dyne C. 108 dyne D. 109 dyne

74. Otto cycle is also known as


A. Constant pressure cycle C. Constant temperature cycle
B. Constant volume cycle D. Constant entropy cycle

75. What is the most common alloying ingredient in copper?


A. Iron B. Zinc C. Lithium D. Magnesium

76. A car going 85 kph on a straight road is brought uniformly to a stop in 10 s. How far
does the car travel during that time?
A. 90 m B. 100 m C. 120 m D. 110 m

Solution:

𝑉𝑜+𝑉𝑓
S= (𝑡)
2

Vo = 0
85 𝑘𝑚 1000𝑚 1ℎ𝑟 1𝑚𝑖𝑛 𝑚
Vf = 𝑥 𝑥 60 𝑚𝑖𝑛𝑠. 𝑥 60 𝑠𝑒𝑐𝑠 = 23.61
ℎ𝑟 1𝑘𝑚 𝑠

0 + 23.61
𝑆 = 𝑥10 = 𝟏𝟏𝟖. 𝟎𝟓 ≈ 𝟏𝟐𝟎𝒎
2

90
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
77. Which of the following conductors is not applicable on wet locations?
A. Type THHN B. Type THW C. Type RHW D. Type THWN

78. Which characteristic of a wave changes as the wave travels across a boundary
between two different m
A. frequency B. period C. phase D. speed

79. For office building, a general lighting load of ____ VA/m 2 shall be used.
A. 12 B. 16 C. 24 D. 28

80. The platter of the hard drive of a computer rotates at 7200 rpm. If the reading head
of the drive is 3.00 cm from the rotation axis, what is the linear speed of the point on
the platter just below it?
A. 22.6 m/s B. 26.2 m/s C. 18.9 m/s D. 19.8 m/s

Solution:

7200𝑟𝑒𝑣 1 𝑚𝑖𝑛 2𝜋𝑟𝑎𝑑 3𝑥10−2 𝒎


𝐿𝑖𝑛𝑒𝑎𝑟 𝑆𝑝𝑒𝑒𝑑 = 𝑥 𝑥 𝑥 = 𝟐𝟐. 𝟔
𝑚𝑖𝑛 60 𝑠𝑒𝑐𝑠 1 𝑟𝑒𝑣 1 𝑟𝑎𝑑 𝒔

81. A market situation where there is only one seller with many buyers.
A. Monopoly B. Monopsony C. Oligopoly D.Oligopsoly

82. Study of motion with reference to the force which causes the motion is.
A. kinematics B. kinetics C. statics D. dynamics

83. A man who won P300, 000 in a lottery decided to place 50 percent of his winnings
in a college education of his son. If the money earn 14 percent a year compounded
quarterly, how man have at the end of 10 years, when his will starting his college
education?
A. P593, 467.98 C. P593, 888.96
B. P682, 456.96 D. P375, 958.

Solution:

𝑟
𝐹 = 𝑃 (1 + 𝑚)𝑛
0.14 10(4)
𝐹 = 150,000 (1 + ) = 𝑷𝟓𝟗𝟑, 𝟖𝟖𝟖. 𝟗𝟔
4

91
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
84. In RA 7920, section 23 of article III: Issuance of Certificates of Registration. The v
bprofessional is renew licence every _______ years upon payment of registration
fees.
A. 1 B. 2 C. 3 D. 6

85. Water flows from a reservoir with an elevation of 25 m out a short pipe that contains
a turbine power. The exit is at an elevation of 5 m. If the flow rate is 0.01 m 3/s, the
maximum power output is.
A. 1960 W B. 2430 W C. 2560 W D. 3480 W

Solution:

P = γQH

KN m³
P = (9.81 m³ ) (0.01 ) (25m - 5m)
s
∴ 𝑷 = 𝟏𝟗𝟔𝟐 𝑾 𝒐𝒓 𝟏𝟗𝟔𝟎 𝑾

86. It is the ratio of the ultimate stress to the allowable stress.


A. proportionally constant B. strain C. bulk modulus D. factor of

87. What is the entropy of a pure substance at a temperature of absolute zero?


A. Unity B. Zero C. Infinity D. Undefined

88. Which of the following closely related to d’Alembert’s theorem?


A. Newton’s first law of motion C. Newton’s third law of motion
B. Newton’s second law of motionD. Bernoulli’s theorem

89. What is the energy equivalent of a mass of 1 kilogram?


A. 4.5 x 1016 J B. 9 x 1016 J C. 4.5 x 1012 J D. 9 x 1012
J
90. What element is known as the lightest metal?
A. Aluminium B. Manganese C. Magnesium D. Lithium

91. The area of the shear diagram of a beam between any two points on the beam is
equal to the
A. change in shear between the two points.
B. total shear beyond the two points.
C. change in moment between the two points.
D. change in deflection between the two points.

92. Which element is the best conductor of electricity?

92
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. gold B. silver C. copper D. aluminium

93. An automobile uses 100 hp to move at a uniform speed of 60 mph. What is the
thrust force provided by the engine?
A. 530 lbf B. 625 lbf C. 1100 lbf D. 1800 lbf

Solution:

𝑷=𝑭𝒙𝑽
5280 𝑓𝑡⁄
100(550) = 𝐹 𝑥 [60 𝑥 ] 𝑠
3600

∴ 𝑭 = 𝟔𝟐𝟓 𝒍𝒃 − 𝒇𝒕

94. Litmus paper changes from blue to red when a solution tested is
A. a blue dye B. an acid C. a red dye D. a base

95. RA 9136 has four sectors, which of the following is not included?
A. system operation B. supply C. distribution D. generation

96. The radius of gyration of a circular section of diameter d is:


A. d/16 B. d/4 C. d D. d/2

97. Enthalpy of an ideal gas is a function only of

A. internal energy C. the product of pressure and specific volume


B. pressure D. temperature

98. A homogeneous round bar of diameter D, length L, and total weight W is hung
vertically from one end. If the modulus of elasticity, what is the tota; elongation of
the bar?
A. B. C. D.

99. A heavy brass plumb-bob suspended from a 38-inch cord was observed to have
a natural period of osci of about two seconds if pulled 24 inches to one side and
then allowed to spring freely. If an astronaut repeat this experiment on the moon
where the gravitational attraction is approximately 1/6 th that of the observed
period would be:
A. 0.33 second B. 0.82 second C. 4.90 seconds D. 12 seconds

Solution:

93
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2016
ENGINEERING SCIENCES AND ALLIED SUBJECTS

100. It is the claim of anyone to ownership.


proprietorship B. liability C. equity D. assets

94
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM AUGUST 2015

1. An iceberg has a density of 917 kg/m3. If it floats in freshwater, what percent of


iceberg’s volume will be visible?
A. 91.7% B. 8.3% C. 93.1% D. 6.9%

Solution:

917 𝑘𝑚/𝑚3
% 𝑣𝑖𝑠𝑖𝑏𝑙𝑒 = 1 − 1000 𝑘𝑔/𝑚3
% 𝑣𝑖𝑠𝑖𝑏𝑙𝑒 = 𝟖. 𝟑%

2. An iceberg has a density of 917 kg/m3. If it floats in freshwater, what percent of


iceberg’s volume is submerged?
A. 91.7% B. 8.3% C. 93.1% D. 6.9%

Solution:
917 𝑘𝑚/𝑚3
% submerged = 1 - 1000 𝑘𝑔/𝑚3
∴ 𝟗𝟏. 𝟕%

3. Commercially used pressure measuring device is


A. Bourdon tube gauge C. Kelvin gauge
B. Manometer D. Barometer

4. In thermodynamics we focus our attention on which forms of energy?


A. kinetic B. potential C. internal D. total

5. The purpose of copper steel alloying is to increase


A. atmospheric corrosion resistance C. corrosion resistance
B. hardness and strength D. deoxidation

6. The abbreviation for binary digit


A. bid B. bin C. bit D. byte

7. A carwash area is classified as


A. Wet location C. Damp location
B. Dry location D. Moist location
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
8. Installations underground or in concrete slabs or masonry in direct contact with the
earth.
A. Wet location C. Damp location
B. Dry location D. Moist location
9. What impurity in steel can cause “red shortness” which means the steel becomes
unworkable at high temperature?
A. Sulfur C. Manganese
B. Silicon D. Phosphorus

10. A system or circuit conductor that is intentionally grounded.


A. Grounding Conductor C. Grounding Electrode Conductor
B. Grounded Conductor D. Grounding Equipment

11. A conducting connections, whether intentional or accidental, between an electric


circuit or equipment and the earth, or to some conducting body that serves in place
of the earth.
A. Grounded B. Ground C. Short D. Fault

12. Aluminum can be added to steel to produce


A. killed steel B. dead steel C. live steel D. first steel

13. Which of the following is an alkaline earth metal?


A. Ba B. Ti C. Li D. Na

14. The second law of thermodynamics can be stated as:


I. Heat flows spontaneously from a hot object to a cold one, but not the reverse;
II. Natural processes tend to move toward a state of greater disorder or greater
entropy
A. I only B II only C. I and II D. Neither I nor II

15. Structural steel elements subjected torsion develop


A. tensile stress C. shearing stress
B. compressive stress D. bending stress

16. Formula of kinetic energy:


A. v2/2m B. mv2/2 C. 2mv2 D. mgh

17. The three moment equation may be used to analyze


A. a continuous beam C. a step tapered column
B. a beam loaded at the third points D. a three element composite beam

96
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
18. An essential part of a large dam and provides an efficient and safe means of
releasing flow of water that exceeds the design capacity of the reservoir.
A. spillway B. weir C. culverts D. standpipe

19. An open system first law should be utilized for all of the following except:
A. nozzle
B. turbine
C. a piston-cylinder device with no inlet/exhaust valves
D. a compressor

20. The property that characterizes a material’s ability to be drawn into wire is its
A. tensile strength C. ductility
B. thermal conductivity D. fatigue endurance limit

21. You need P40,000 per year for four years to go to college. Your father invested
P50,000 in a 7% account for your education when you were born. If you withdraw
the P40,000 at the end of your 17th, 18th, 19th, and 20th years, how much money will
be left in the account at the end of your 21st year?
A. P17,000 B. P25,000 C. P34,000 D. P40,000

Solution:

At condition 1:
P = P50,000
i = 0.07
n = 21
At condition 2:
P = P40,000
i = 0.07
n=4
( 1 + 0.07)4 − 1
= 50,000( 1 + 0.07)21 – 40,000 [ ] (1 + 0.07)
0.07
∴ 𝑷𝟏𝟔, 𝟗𝟗𝟖. 𝟓𝟔 ≈ 𝑷𝟏𝟕, 𝟎𝟎𝟎

22. What do you call a system in which there is a flow of matter through the boundary?
This system usually encloses the device that involves mass flow, such as
compressor, turbine, or nozzle.
A. Closed system
B. Open system
C. Isolated system

97
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
D. All of these

23. What system in which there is no exchange of matter with the surrounding or mass
does not cross its boundaries?
A. Closed system
B. Open system
C. Isolated system
D. Non flow system

24. Find the present worth if interest after 3 years and 6 months is P900 at simple
interest rate of 4% per annum.
A. P6,429 B. P6,249 C. P6,117 D. P6,171

Solution:
𝐼 = 𝑃𝑖𝑛
900 = 𝑃 (0.04) (3.5)
𝑃 = 𝑷𝟔𝟒𝟐𝟖. 𝟓𝟕 ≈ 𝑷𝟔𝟒𝟐𝟗

25. Which of the following is not a function of computer?


A. understanding B. processing C. controlling D. inputting

26. Change in enthalpy occurs at constant _________.


A. pressure B. volume C. temperature D. entropy

27. The first law of thermodynamics is based on which of the following principles?
A. Conservation of mass C. Action and reaction
B. Conservation of energy D. The entropy-temperature relationship

28. Impulse type turbine named after his creator.


A. Pelton B. Kaplan C. Francis D. Propeller

29. In flow chart, what is the symbol used in decision making?


A. oval B. rectangle C. diamond D. square

30. Which of the following is not a fundamental rule in PEC?


A. Construction Rule C. Installation Rule
B. Wiring Rule D. Manufacturing Rule

31. Reversed Joule cycle is also known as


A. Ranking Cycle

98
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
B. Sterling Cycle
C. Brayton Cycle
D. Bell-Coleman Cycle

32. Also known as PRC Renewal Law


A. R.A. 8189 B. R.A. 8981 C. R.A. 7920 D. R.A. 7918

33. 111 + 110 = __________?


A. 1100 B. 1110 C. 1101 D. 1011

Solution:

111
+ 110
1101

34. 1A9B is __________ in decimal?


A. 6812 B. 6811 C. 6810 D. 6809

Solution:

1A9B
11 x 160 =11
9 x 161 = 144

10 x 162 = 2560
1 x 163 = 4096
681110

35. What is the final temperature of the mixture if 128g of cold water at 3° C is mix with
289g of hot water at 91° C?
A. 72° C B. 62° C C. 78° C D. 64° C

Solution:

Q gained = Q loss
M1C∆T = M2C∆T
M1C (T mix – T1) = -M2C (T mix – T2)
(128g) (1) (T mix – 3) = -(289g) (1) (T mix – 91)
𝑻 𝒎𝒊𝒙 = 𝟔𝟑. 𝟗𝟖° 𝑪 ≈ 𝟔𝟒° 𝑪

99
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
36. In piston-cylinder arrangement if weight of 15,000 N located at bigger piston of A =
0.1 sq. m., what is the force exerted in a smaller piston with A = 0.002 sq. m.?
A. 200 N B. 400 N C. 300 N D. 150 N

Solution:

𝐹1 𝐹2
=
𝐴1 𝐴2

15,000 𝑁 𝐹2
=
0.1 𝑚2 0.002 𝑚2

𝐹2 = 𝟑𝟎𝟎𝑵

37. ASCII means


A. American Standard Code for Information Output
B. American Standard Code for Input Information
C. American Standard Capacity for Information Input
D. American Standard Code for Information Interchange

38. WWW stands for


A. World Wide War C. World Wide Wrestling
B. World Wide Web D. World Wide Workers

39. ALU stands for


A. Arithmetic Logic Unit C. Arithmetic Logic User
B. Arithmetic Logical Unit D. Arithmetic Logical User

40. The simple mathematical statement of the relationship between elastic stress and
strain: stress is proportional to strain. What is this law?
A. Boyle’s Law B. Hooke’s law C. Charle’s Law D. Gas Law

41. 1 kwhr is how many kilojoules?


A. 360 B. 3600 C. 1000 D. 100

42. Given a spring with a spring constant of 60 N/m. What is the work done in
compressing by 4.2cm?
A.0.02 J B. 0.06 J C. 0.03 J D. 0.05 J

Solution:

100
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑁
𝐾 = 60
𝑚
1𝑚
𝑋 = 4.2 𝑐𝑚 𝑥 = 0.042 𝑐𝑚
100𝑐𝑚
𝐾𝐸 = ½ (60) (0.042𝑐𝑚)2
𝑲𝑬 = 𝟎. 𝟎𝟓𝟐𝟗𝟐 𝑱 ≈ 𝟎. 𝟎𝟓 𝑱

43. Find the required diameter of steel member if the tensile design load is 6,000
pounds. Assume a safety factor of 5 based on an ultimate strength of 65,000 lbf/sq.
in.
A. 0.98 in B. 0.86 in C. 0.77 in D. 0.69 in

Solution:

𝑆 𝑢𝑙𝑡𝑖𝑚𝑎𝑡𝑒
SF = 𝑆 𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒
65,000
5 = 𝑆 𝑎𝑙𝑙𝑜𝑤𝑎𝑏𝑙𝑒
S allowable = 13,000 lbf/in2
𝑃
𝑆 = 𝐴
6,000
13,000 = 𝜋(𝑑)2
4
𝒅 = 𝟎. 𝟕𝟕 𝒊𝒏

44. A rocket with an ejection of 2200 m/s is ejecting 1 percent of its mass per second.
What is the initial acceleration?
A. 24 m/s2 B. 22 m/s2 C. 20 m/s2 D. 12 m/s2

Solution:
𝑑𝑚
𝑣
𝑑𝑡
a= -g
𝑚
= 2200 (0.01) – 9.81
𝒎
𝑎 = 𝟏𝟐. 𝟏𝟗
𝒔𝟐

45. Given impulse of 500 N·s. If a mass of housing is 1400 kg and released a mass of
1000 kg, what is the velocity of separation?
A. 0.1429 B. 0.8571 C. 0.1786 D. 1.25

Solution:

𝐹∆𝑡 = 𝑚∆𝑉
500 𝑁 · 𝑆 = 𝑚𝐻 (𝑉2𝐻 – 𝑉)

101
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
500 𝑁 · 𝑆 = 1400 𝑘𝑔 (𝑉2𝐻 – 𝑉) 𝑒𝑞. 1
−500 𝑁 · 𝑆 = 𝑚𝑅 (𝑉2𝑅 – 𝑉)
−500 𝑁 · 𝑆 = 1000 𝑘𝑔 (𝑉2𝑅 – 𝑉) 𝑒𝑞. 2
Solving eq. 1 and eq. 2
𝑉2𝐻 – 𝑉2𝑅 = 𝟎. 𝟖𝟓𝟕𝟏

46. With initial price of P3,000, with 7 percent discount, how much is the discount price?
A. P250 B. P220 C. P200 D. P210

Solution:

𝐷𝑝 = 3000 𝑥 0.07
𝑫𝒑 = 𝑷𝟐𝟏𝟎

47. A price of P1,500 is payable for 70 days, but it has 5 percent discount if paid within
35 days. What is the annual interest rate?
A. 52% B. 15% C. 54% D. 36%

Solution:

𝐹 = 0.95𝐹 (1 + 𝑖𝑛)
35
1500 = 0.95 (1500) (1 = 𝑖 ( ))
360
𝑖 = 𝟎. 𝟓𝟒𝟏𝟑 𝒐𝒓 𝟓𝟒. 𝟏𝟑%

48. An empty glass was initially place with a cube ice. A water was filled into a glass
such that the ice at the tip of the glass. What will happen after the ice melts?
A. cannot be determine since no density of ice and water are given
B. some spilled
C. some spilled on the side of the glass
D. nothing spilled

49. An object is placed 3 feet from the center of a horizontally rotating platform. The
coefficient of friction is 0.30. The object will begin to slide off when the platform
spend is nearest to:
A. 12 rpm B. 17 rpm C. 22 rpm D. 33 rpm

Solution:

ƩFv = 0

102
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
N-𝜔 = 0
N = 𝜔 = mg
ƩFH = MaH = Map
µN = Mar
V2 = µgr
(𝜔r)2 = µgr
𝜔2 r2 = µgr
µ𝑔
𝜔2 = 𝑟
µ𝑔
𝜔 =√𝑟
(0.30)(32.2)
=√ 3
𝑟𝑎𝑑 1 𝑟𝑒𝑣 60 𝑠𝑒𝑐
𝜔 = 1.79 x 2𝜋 𝑟𝑎𝑑 x
𝑠𝑒𝑐 1 𝑚𝑖𝑛
𝝎 = 𝟏𝟕. 𝟎𝟗 𝒓𝒆𝒗/𝒎𝒊𝒏 ≈ 𝟏𝟕 𝒓𝒑𝒎

50. Regnault’s law relates to


A. Internal Energy B. Specific Heat C. Specific Volume D. Entropy

51. Dual Combustion cycle is used in:


A. Petrol Engine B. Diesel Engine C. Steam Engine D. Gas Turbine

52. In a Throttling process


A. There is no work done C. There is no change in enthalpy
B. There is no heat transfer D. All of these

53. For some interest rate i and some number of interest periods n, the uniform series
capital recovery factor is 0.0854 and the sinking fund factor is 0.0404. The interest
rate i must be
A. 3.5 percent B. 4.5 percent C. 6 percent D. 8 percent

Solution:

𝑆𝐹 + 𝑖 = 𝐶𝑅𝐹
0.0404 + 𝑖 = 0.0854
𝑖 = 0.0854 – 0.0404
𝑖 = 0.045 𝑥 100
𝒊 = 𝟒. 𝟓%

54. A 60-inch diameter steel pipe, 3/8-inch-thick, carries water under a pressure head of
550 feet. Determine the hoop stress in the steel.

103
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 4,760 psi B. 38,080 psi C. 9,520 psi D. 19,040 psi

Solution:

P = gh
𝑃𝐷
S = 2𝑇
1
(62.4)(550)(60) ( )
144
S= 3
2( )
8
𝑺 = 𝟏𝟗, 𝟎𝟔𝟔. 𝟔𝟔𝟕 𝒑𝒔𝒊

55. If two objects have the same momentum, but different masses, which of these is
possible?
A. the one with less mass has more kinetic energy
B. the one with more mass requires more impulse to bring it to that momentum from
rest
C. the same work is done to each to accelerate it from rest
D. they have the same velocity

56. The present worth of an obligation of $10,000 due in 10 years if money is worth 9
percent is nearest to
A. $10,000 B. $9,000 C. $7,500 D. $4,500

Solution:

𝐹 = 10,000 (1 + 0.09)2
𝑭 = 𝟒, 𝟐𝟐𝟒. 𝟏𝟏

57. The wheel of an automobile spinning at 180 rpm begins to experience a 10 rad/s 2
angular acceleration. What is the angular velocity of the wheel after 5 seconds?
A. 230 rpm B. 275 rpm C. 477 rpm D. 657 rpm

Solution:

60
𝜔 = 180 + (10) (5) (2𝜋)
𝝎 = 𝟔𝟓𝟕. 𝟒𝟔 𝒓𝒑𝒎

58. Which of the following is not a ductile metal?


A. Aluminum B. Copper C. Mild Steel D. Lead

104
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
59. As a person moves closer to a plane mirror, the size of the image formed by the
mirror
A. remains the same C. gets smaller
B. gets larger D. increases, then decreases

60. A manufacturing company buys a machine for P500,000. It estimates the machine’s
useful life is 20 years and that it can be sold for P50,000. Using straight line
depreciation, what is the annual depreciation charge?
A. P20,000 B. P22,500 C. P25,000 D. P27,500

Solution:
(𝑐𝑜𝑠𝑡 − 𝑠𝑎𝑙𝑣𝑎𝑔𝑒 𝑣𝑎𝑙𝑢𝑒)
𝑑=
𝑢𝑠𝑒𝑓𝑢𝑙 𝑙𝑖𝑓𝑒

(500,000−50,000)
𝑑= 20

∴ 𝒅 = 𝑷 𝟐𝟐, 𝟓𝟎𝟎
61. What is the new volume of 20 liters of gas at STP which experience a pressure
increase of 2 atm and temperature increase of 75 degrees?
A. 12.75 liters B. 25.5 liters C. 17 liters D. 8.5 liters

Solution:

𝑃1𝑉1 𝑃2𝑉2
= 𝑇2
𝑇1
1 (20) 3 (𝑉2)
=
273 348
𝑽𝟐 = 𝟖. 𝟓 𝑳

62. A piece of property is purchased for P100,000 and yields P10,000 yearly profit. If the
property is sold after five years, what is the minimum price to break-even, with
interest at 6 percent?
A. P50,000 B. P65,540 C. P77,430 D. P83,140

Solution:

𝐹1 = 100,000 (1 + 0.06)5 = 133,822.56

(1. 𝑜6)5 − 1
𝐹2 = 10,000 [ ] = 56,370.93
0.06

105
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐹 = 𝐹1 – 𝐹2 = = 133,822.5578 − 56,370.9296
𝑭 = 𝟕𝟕, 𝟒𝟓𝟏. 𝟔𝟐𝟖𝟐

63. The executive officer of the Board of Electrical Engineering is __________.


A. PRC Commissioner C. Civil Service Commission
B. Chairman of the Board of EE D. IIEE President

64. The pressure head of an oil of sp. gravity 0.75, corresponding to a pressure head of
6 m of water will be
A. 9 m B. 4.5 m C. 8 m D. 6 m

Solution:
6
𝑃𝑟𝑒𝑠𝑠𝑢𝑟𝑒 𝐻𝑒𝑎𝑑 = =𝟖𝒎
0.75

65. 65. If the speed of light in a vacuum is c, then the speed of light of light in a medium
with an index of refraction of 2 will be
A. c/2 B. 2c C. c/4 D. 4c

Solution:
𝑐
𝐼𝑛𝑑𝑒𝑥 𝑟𝑒𝑓𝑟𝑎𝑐𝑡𝑖𝑜𝑛: 𝑛 = 𝑣
𝑐
2=
𝑣
𝑐
𝑣=
2

66. The number of neutrons in an atom with an atomic number of 26 and a mass
number of 56 is
A. 26 B. 56 C. 30 D. 82

Solution:

𝑀𝑎𝑠𝑠 𝑛𝑢𝑚𝑏𝑒𝑟 – 𝐴𝑡𝑜𝑚𝑖𝑐 𝑛𝑢𝑚𝑏𝑒𝑟


56 − 26 = 𝟑𝟎

67. The radius of gyration of a circular section of diameter d is:


A. d/2 B. d/4 C. d D. d/8

68. Water flows radially outwards from a circular shower head through the side of a
cylinder 2 mm high and 25 cm in diameter, with an average velocity of 2 m/s. What
is the flow rate?

106
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 3.14 liters/s B. 3.41 liters/s C. 0.314 liters/s D. 1.0 liters/s

Solution:

69. The ozone layer exists primarily in what section of the atmosphere?
A. Troposphere
B. Stratosphere
C. Mesosphere
D. Ionosphere

70. The majority of the rocks in the Earth’s crust are:


A. igneous B. metamorphic C. sedimentary D. basalt

71. What element is added to copper to make it extremely hard?


A. Silicon B. Aluminum C. Lead D. Zinc

72. The maximum bending movement in a simple supported beam of span L and
carrying a central concentrated load “W” is
A. WL B. WL/2 C. WL/4 D. 2WL

73. An object orbits the star in an elliptical orbit. The distance at aphelion is 2a and the
distance at perihelion is a. Determine the ratio of the object’s speed at perihelion to
that at aphelion.
A. 2 B. √2 C. 1 D. 4

Solution:

At aphelion and at perihelion, the velocity is perpendicular to the radial


line, that is, theta = 90°. Using the conservation of angular momentum that is
implied by Kepler's second Law - equal areas are swept out in equal time.
1
𝐿= 𝑟𝑣 ∗ 𝑠𝑖𝑛𝜃
2
Therefore

𝑟𝑝 ∗ 𝑣𝑝 = 𝑟𝑎 ∗ 𝑣𝑎
(2𝑎)𝑣𝑝 = (𝑎)𝑣𝑎

107
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
where the subscripts p and a refer to perihelion and aphelion, respectively. The
ratio the velocity perihelion to the velocity at aphelion is
𝑣𝑝 𝑟𝑎
=
𝑣𝑎 𝑟𝑝
𝑣𝑝 2𝑎
= =𝟐
𝑣𝑎 𝑎
74. The most abundant element in the universe is
A. He B. C C. H D. O

75. It is the payment for the use of borrowed money.


A. load B. interest C. maturity value D. principal

76. For an orifice, head above the orifice is 4 m, and C C = 0.6. Then the actual velocity
of flow through the orifice will be:
A. 5.32 m/s B. 8.96 m/s C. 12.56 m/s D. 16.32 m/s

Solution:

𝑉 = 𝐶𝐶 √2𝑔ℎ
𝑉 = 0.6 √2 (9.81)(4)
𝑽 = 𝟓. 𝟑𝟐 𝒎/𝒔
77. The mass of air in a room 3 x 5 x 20 is known to be 350 kg. Determine the specific
weight.
A. 11.45 N/cu.m. B. 11.54 N/cu.m. C. 12.63 N/cu.m. D. 12.36 N/cu.m.

Solution:

𝑚 350 𝑘𝑔
P= = 300 𝑚3
𝑣
7
p = 6 kg/m3
y= 7
pg = ( ) (9.81)
6
𝒚 = 𝟏𝟏. 𝟒𝟒𝟓 𝑵/𝒎𝟑

78. An electrical engineer wishes to accumulate a total of P10,000,000 in a saving


account at the end of 10 years. If the bank pays only 4 percent compounded
quarterly, what should be the initial deposit?
A. P6.76 M B. P6.72 M C. P6.17 M D. P 6.18 M

108
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

0.04
(1+ )−1
4
P = 10,000,000 [ 0.04 ]
4
𝑷 = 𝟔, 𝟕𝟏𝟔, 𝟓𝟑𝟏. 𝟑𝟖𝟗

79. A debt of P10,000 with 10% interest compounded semi-annually is to be amortized


by semi-annual payments over the next 5 years. The first due in 6 months.
Determine the semi-annual payment.
A. P1,295.05 B. P1,264.05 C. P1,682.80 D. P1,534.80

Solution:

0.1 −2(5)
(1+ ) −1
2
A = 10,000 [ 0.1 ]

2

𝑨 = 𝟏, 𝟐𝟗𝟓. 𝟎𝟓

80. The brass wire has a triangular cross-section, 2 mm on a side. If the yield stress for
brass is 205 MPa, determine the maximum torque to which it can be subjected so
that the wire will not yield.
A. 0.82 N-m B. 0.082 N-m C. 0.95 N-m D. 0.095 N-m

Solution:
20𝑇
S max = 𝑎3
3
(205𝑥106 )(2𝑥10−6 )
T= 20
𝑻 = 𝟎. 𝟎𝟖𝟐 𝑵 · 𝒎

81. Determine the maximum horsepower a solid steel shaft 50 mm in diameter can
transmit at 4 rev/sec if the working stress in shear is 90 MPa.
A. 35.5 kW B. 64.6 kW C. 55.3 kW D. 33.5 Kw

Solution:

16𝑇
S = 𝜋 (50𝑥10−3 )3
T = 2,208.93 N·m
2𝜋𝑁𝑇 2𝜋 (4𝑥60)(2,208.93)
P= =
60 60
𝑷 = 𝟓𝟓. 𝟓 𝑲𝑾

109
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
82. A person throws a stone upward at an angle of 30degrees to the horizontal. It lands
173.2 ft. measured horizontally and 6 ft. below the person’s arm measured vertically.
Determine the time of flight.
A.1.838 s B. 2.563 s C. 3.642 s D. 4.258 s

Solution:

𝑥2𝑔
−𝑦 = 𝑥𝑡𝑎𝑛(Ɵ) − 2𝑉𝑜 3 𝑐𝑜𝑠2 30
(173.2)2 (32.2)
−6 = (173.2)𝑡𝑎𝑛(30) − 2𝑉𝑜 2 𝑐𝑜𝑠2 30
𝑉𝑜 = 77.94 𝑓𝑡/𝑠

Therefore:
173.2 = (77.94)𝑐𝑜𝑠(30)𝑡
𝒕 = 𝟐. 𝟓𝟔𝟔 𝒔𝒆𝒄

83. Determine the elongation in a helical steel spring composed of 20 turns of 20 mm


diameter wire on a man radius of 80 mm when the spring is supporting a load of 2
kN. Use G = 83GPa.
A.94.8 mm B. 98.7 mm C. 89.6 mm D. 86.8 mm

Solution:

64𝑃𝑅 3 𝑛
Elongation = 𝐺𝑑^4
64 (2𝑥103 )(80𝑥10−3 ) (20)
Elongation = (83𝑥109 )(20𝑥20−3 )4
𝑬𝒍𝒐𝒏𝒈𝒂𝒕𝒊𝒐𝒏 = 𝟗𝟖. 𝟔𝟗 𝒎𝒎

84. A car travels 100 miles to city A in 2 hours, and then travels 200 miles to city B in 3
hours. What is the average speed of the car for the trip?
A. 45 mph B. 58.3 mph C. 60 mph D. 66.7 mph

Solution:

100+200
Ave. speed = 2+3
𝑨𝒗𝒆. 𝒔𝒑𝒆𝒆𝒅 = 𝟔𝟎 𝒎𝒑𝒉

85. Determine the maximum deflection of a 3 cm x 24 cm rectangular aluminum beam, 5


m long, if a concentrated load of 800 N acts downward at its midpoint.
A. 0.28 m B. 0.36 m C. 0.18 m D. 0.10 m

110
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

𝑆1+𝑆2
Vave = 𝑇1+𝑇2

100+200
Vave = 2+3
𝑽𝒂𝒗𝒆 = 𝟔𝟎 𝒎𝒊𝒍𝒆𝒔/𝒉𝒓

86. The Hooke’s law holds good within


A. yield point B. elastic limit C. plastic limit D. Euler’s limit

87. A force of 40 N is needed to set a 10-kg steel box moving across a wooden floor.
The coefficient of static friction is
A. 0.08 B. 0.25 C. 0.4 D. 2.5

Solution:

F = µN
F = µmg
𝐹 40
µ = 𝑚𝑔 = 10 (9.81)
µ = 𝟎. 𝟒

88. The Pauli Exclusion Principle states that


A. any atoms with a free s orbital can form bonds
B. no two atoms can occupy the same orbital unless their spins are different
C. two atoms can occupy the same orbital unless their spins are different
D. atoms of the same configuration do not change

89. What mass in grams of solute is needed to prepare 3.50 L of 0.400 M NaOH?
A. 54 B. 56 C. 52 D. 58

Solution:

NaOH
1x1 =1
1 x 16 = 16
1 x 23 = 23
40g/mole
0.400 = m/40
3.5

111
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝒎 = 𝟓𝟔 𝒈𝒓𝒂𝒎𝒔

90. The speed with which a liquid escapes from a vessel through an orifice is given by
A. Archimedes’ Principle C. Bernoulli’s Theorem
B. Torricelli’s Theorem D. Flow equation

91. A refrigerator gives off 3 J heat for every joule of mechanical energy input. Its
coefficient of performance is
A. 1 B. 2 C. 3 D. 4

Solution:

W = QH - QL
QL = Q H – W
QL = 3J – 1J
QL = 2J
𝑄𝐿 2𝐽
𝐶. 𝑂. 𝑃. = = = 𝟐
𝑊 1𝐽

92. What is Article II of Code of Ethics for Electrical Engineers?


A. Relations with Client and Employer C. Professional Life
B. Relations with Fellow Engineers D. Penal Provisions

93. The minimum diameter of a longitudinal bar in a column is


A. 6 mm B. 8 mm C. 12 mm D. 16 mm

94. RA 7920, Rule 2(o) defining?


A. IIEE B. DECS C. CHED D. TESDA

95. Which of the following is the poorest conductor of electricity?


A. Carbon B. Silver C. Steel D. Aluminum

96. Who invented the barometer?


A. Torricelli B. Avogadro C. Rutherford D. Becquerel

97. 97. Calculate the nitrogen pressure in a mixture of 0.500 mol of oxygen and 0.750
mol of nitrogen with a total pressure of 40.0 kPa.
A.8 kPa B. 16 kPa C. 24 kPa D. 40 kPa

112
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

𝜂𝑁2
PN2 = 𝜂𝑁2+ 𝜂𝑜2 x P total
0.750
PN2 = 0.750+0.50 x 40 kPa
𝑷𝑵𝟐 = 𝟐𝟒 𝒌𝑷𝒂

98. During polytropic process 10 lb of an ideal gas, whose R = 40 ft-lbf / lbm-deg R and
Cp = 0.25 BTU / lb-deg R changes state from 20 psia and 40 deg F to 120 psia and
340 deg F. Determine ∆U.
A. 585.6 BTU B. 595.5 BTU C. 750.6 BTU D. 780.5 BTU

Solution:

Cp = Cv + R
Cv = Cp – R
1 𝐵𝑇𝑈
Cv = 0.25 – (−40 778 𝑓𝑡.𝑙𝑏𝑓)
Cv = 0.1986
∆U = mCv∆T
∆U = 10 (0.1986) (340-40)
∆𝑼 = 𝟓𝟗𝟓. 𝟖 𝑩𝑻𝑼

99. What is the pH of a 0.014 M Ca(OH)2 solution?


A. 1.55 B. 1.85 C. 12.15 D. 12.45

Solution:

2 (0.014) = 0.028
-Log (0.028) = 1.55
PN = 14 – 1.55
𝑷𝑵 = 𝟏𝟐. 𝟒𝟓

100. A metal plate 4.00 mm thick has a temperature difference of 32.0 deg C between
its faces. It transmits 200 kcal/h through an area of 5.00 sq. cm. Calculate the
thermal conductivity of this metal in W/m-K.
A. 85.5 B. 58.5 C. 68.5 D.86.5

Solution:

113
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑘𝐴𝑡∆𝑇
Q= 𝑑
𝑄 𝑘𝐴∆𝑇
=
𝑡 𝑑
1 2 1𝐾
𝑘[5 𝑥 ( ) ](32 𝐶 𝑥
100 1𝑐
(200 Kcal/hrs) (4186 J / Kcal) (1hr/3600s) = 4 𝑥 10 ̄³
𝐽 𝑘(5 𝑥 10−4 )(32)
232. 56 𝑆 = (4 𝑥 10−3 )
𝒌 = 𝟓𝟖. 𝟏𝟒 𝑾/𝒎 – 𝑲

114
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM MARCH 2015

1. Partially protected locations under canopies, marquees, roofed open porches, and
like locations, and in locations subject to moderate degrees of moisture, such as
some basements, some barns, and some cold storage warehouses.
A. Dry B. Damp C. Moist D. Wet

2. A location not normally subjects to dampness or wetness. A location classifies as


_______ may be temporary subject to dampness or wetness, as in the case of a
building under construction.
A. Dry B. Damp C. Moist D. Wet

3. Combination of laminar and turbulent flow


A. Critical B. Continuous C. Laminar D. Turbulent

4. A system or circuit conductor that is intentionally grounded,


A. Grounding conductor C. Grounding electrode conductor
B. Grounded conductor D. Grounding equipment

5. Most common pressure measuring device use today


A. Bourdon tube gauge C. Kelvin gauge
B. Manometer D. Barometer

6. Poisson’s Ratio is the ratio of the


A. Unit lateral deformation to the unit longitudinal deformation
B. Unit stress to unit strain
C. Elastic limit to proportional limit
D. Shear strain to compressive strain

7. Which is not covered by thermodynamics?


A. Utilization of energy C. Transfer of energy
B. Transformation of energy D. Storage of energy

8. What is the SI unit of mass?


A. Newton B. Kilogram C. Slug D. Pound

9. What is the SI unit of length?


A. Meter B. Centimeter C. Feet D. Inches

10. The differential of the shear equation is which one of the following?
A. Load on the beam C. Bending moment of the beam
B. Tensile strength of the beam D. Slope of the elastic curve

115
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
11. Under very slow deformation and high temperature, if it is possible to have some
plastic flow in crystal at a shear stress lower than the critical shear stress. What is
this phenomenon called?
A. Slip B. Twinning C. Creep D. Bending
12. Which of the following elements and compounds is unstable and its pure form?
A. Sodium (Na) C. Carbon Dioxide (CO2)
B. Helium (He) D. Neon (Ne)
13. BIOS stands for
A. Basic Input Output Society C. Base Input Output Society
B. Basic Input Output System D. Base Input Output System
14. 14. Mandarin Bank advertise 9.5% account that yields 9.84% Annually. Find how
often interest is compounded
A. Monthly B. Bimonthly C. Quarterly D. Annually
Solution:
0.095 𝟒
(1+ ) – 1 = 9.84 %
𝟒
Therefore, it is quarterly.
15. The minimum diameter of a steel ground electrode is
A. 10 mm B. 12 mm C. 14 mm D. 16 mm
16. The branch of mechanics that deals with bodies in motion is known as __________.
A. Statics B. Dynamics C. Kinetics D. Annually
17. Bernoulli’s equation is based on
A. The second law of motion C. The conservation of momentum
B. The third law of motion D. The conservation of energy
18. Pluto travels from perihelion to aphelion. What is the work done by gravity in Pluto?
A. Zero C. Positive
B. Negative D. Undetermined

19. Carnot cycle is maximum efficiency in __________ engine.


A. Steam B. Gas C. Reversible D. Well lubricated

20. It is the interest earned by the principal which is added to the principal will also earn
an interest for the succeeding periods.
A. Compound interest C. Discount
B. Simple interest D. Interest rate

21. An ice with mass of 0.9 kg ids freely floating in water. Find the buoyant force
experienced by the ice.
A. 7.8 N B. 8.82 N C. 10.2 N D. 9.64 N

Solution:

116
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
m
BF = mg = (0.9kg) (9.81 ) = 𝟖. 𝟖𝟐𝟗𝐍
s2
22. What refers to the case hardening process by which the carbon content of the steel
near the surface of the part is increased?
A. Carburizing C. Normalizing
B. Annealing D. Mar tempering

23. If two balls are thrown with the same initial velocity, with one ball is thrown 20
degrees above horizontal and the other is thrown horizontally. Neglecting air
resistance, which ball will hit the ground with the greatest speed?
A. The ones thrown horizontally
B. The ones thrown 20 degrees’ angle
C. Both balls will land in the same velocity
D. Lack of data

24. If an automobile wheel 32 in diameter rotates at 800 r/min, what is the speed of the
car in mph?
A. 12.1 B. 24.2 C. 76.2 D. 152. 4

Solution:

d = 32”
w = 800 rev/min
v =?
v = rw
v
w=
r
𝑟𝑒𝑣 2𝜋 𝑟𝑎𝑑 1𝑚𝑖𝑛
𝑤 = (800 )( )( ) = 83.78𝑟𝑎𝑑/𝑠𝑒𝑐
𝑚𝑖𝑛 1𝑟𝑒𝑣 60𝑠𝑒𝑐
1ft
d = 32in ( ) = 2.67ft
12in
d 2.67
v = rw = ( ) w = ( ) (83.78)
z 2
ft 1mi 3600s
v = (111.71 ) ( )) ( ) = 𝟕𝟔. 𝟐 𝐦𝐢/𝐡𝐫
s 5280ft 1hr

25. MS-DOS is a type of?


A. System software
B. Operating system
C. Application software
D. System architecture

26. MS-WORD is a type of


A. System software C. Application software
B. Operating system D. System architecture

117
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
27. What is CD-ROM?
A. Compact Disk Read Only Memory
B. Compatible Disk Read Only Memory
C. Compact Data Read Only Memory
D. Compatible Data Read Only Memory

28. What is the octal equivalent of the hexadecimal number EE?


A. 356 B. 365 C. 653 D. 635

Solution:

EE16 = 111011102
11|101|110 = 3568

29. (III) base 2 + (III) base 2 = (_____) base 2.


A. 11011 B. 11101 C. 1110 D. 11100

Solution:

111
+111
11102

30. The second law of thermodynamics can be stated as:


I-Heat flows spontaneously from a hot object to a cold one, but not the reverse;
II-Natural processes tend to move toward a state of greater disorder or greater
entropy.
A. I only B. II only C. I and II D. Neither I/II

31. Who is not a member of the board EE


A. Francis V. Mapile C. Gregorio T. Cayetano
B. Fortunato C. Leynes D. Jaime V. Mendoza

32. For REE board examination, the passing general average is 70% provided there is
no grade below ____ in any of the 3 subjects.
A. 50 % B. 60% C. 65% D. 40%

33. What is the weight percentage of electrical engineering professional subjects?


A. 40 B. 35 C. 45 D. 25

34. In an ideal gas, both pressure and temperature increases to twice the original
pressure and temperature respectively. If the original volume is Vo, then the new
volume is
A. 2Vo B. Vo C. Vo/2 D. 4Vo

118
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
35. What is the interest of P 8,600 after 4 years at 12% simple interest rate?
A. P 4,161 B. P 4,116 C. P 4,218 D. P 4, 128

Solution:

I = P(i x n)
I = 8,600 (0.12 x 4)
I = 4,128

36. The ampacity of the fuse should be 125% of the continues load current is covered by
A. Installation design C. Manufacturing design
B. Wiring design D. Construction design

37. Generators and motors should be dust proof is covered by class III,
A. Installation design C. Wiring design
B. Manufacturing design D. Constructional design

38. In thermodynamics we focus our attention on which form of energy?


A. Kinetic B. Potential C. Internal D. Total

39. A beam with rectangular cross-section with breadth of20cm. Determine the depth of
the beam if the maximum shearing stress in beam is 30kg/cm^2 and Vmax = 10,000
kg.
A. 25 cm B. 23 cm C. 20 cm D. 30 cm

Solution:

3𝑉
𝜏= 2𝐴

3(10,000)
30 = 2(20(𝐷))
𝑫 = 𝟐𝟓 𝒄𝒎

40. What is the coal that has been previously burned in an oxygen-poor environment?
A. Tuyere B. Coke C. Diamond D. Hematite

41. What is the most common reinforcement for polymer composites?


A. Boron B. Ceramic C. Graphite D. Grass fiber

42. What is the principle behind fiber optics?


A. Reflection B. Refraction C. Diffraction D. Dispersion

43. A conductor used to connect equipment or the grounded circuit of a wiring system to
a grounding electrodes.
119
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Grounding Conductor
B. Grounded Conductor
C. Grounding Electrode Conductor
D. Grounding Equipment

44. A loan of P 4,000 is made for a period of 16 months at a simple discount rate of 7%,
what future amount is due at the end of the loan period?
A. P 4,373.33 B. P 4,301.08 C. P 4,401.43 D. P 4,411.76

Solution:
𝐷𝑖𝑠𝑐𝑜𝑢𝑛𝑡 𝐷
𝑑= =
𝑃𝑟𝑖𝑛𝑐𝑖𝑝𝑎𝑙 𝑃
𝐷 = 𝑃𝑑
𝐷 = 4000(0.0933)
𝑑 = 𝑑𝑛 𝐷 = 373.33
16
𝑑 = (0.07) ( )
12 𝐹 =𝐷+𝑃
𝑑 = 0.0933
𝐹 = 373.33 + 4000
𝑭 = 𝟒𝟑𝟕𝟑. 𝟑𝟑

45. When magma rocks cool, these rocks are called


A. Granite
B. Sedimentary rocks
C. Igneous rocks
D. Metamorphic rockS

46. The conductor used to connect the grounding electrode to the equipment grounding
conductor to the grounded conductor, or to both, of the circuit at the service
equipment or at the source of a separately derived system.
A. Grounding Conductor
B. Grounded Conductor
C. Grounding Electrode Conductor
D. Grounding Equipment

47. A device intended for the protection of the personnel that functions to de-energize a
circuit or portion thereof within an established period of time when a current to
ground exceeds some predetermined value that is less than that required to operate
the overcurrent protective device of the supply circuit.
A. Grounding Conductor
B. Grounding-Fault Circuit Interrupter
C. Grounding Conductor Equipment
D. Ground-Fault Protection of Equipment

120
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
48. A 40-kg boy walks on a 60-kg log with the speed of 1.5 m/s. What is the speed of the
log with respect to the shore?
A. 1 m/s B. 0.36 m/s C. 0.4 m/s D. 0.8 m/s

49. The maximum bending moment of a beam simply supported at both end and subject
to a total load W uniformly distributed over its length L is expressed by the formula.
A. WL/8 B. WL2/8 C. WL/2 D. WL/4

50. What is the form of the moment diagram of a beam supported at both ends and
carrying a uniformly distributed load?
A. Triangle B. Hyperbola C. Parabola D. Rectangle

51. A byte is composed of how many bits?


A. 2 B. 4 C. 6 D. 8

52. What percentage of the human body will float in fresh water? Average density of
human body is 980 kg/ cu. M
A. 98 B. 2 C. 96 D. 4

53. A gas in the atmosphere that traps sun’s UV rays.


A. Oxygen B. Helium C. Ozone D. Water vapor

54. Adiabatic process is?


A. No heat transfer C. Irreversible
B. Reversible D. Constant pressure

55. P 5,000 will become how much after one year at a simple interest rate of 15%?
A. P 5,850.00 B. P 5,750.00 C P 5,980.00 ` D. P 5,680.00
Solution:
F = P(1 + i) = 5000(1 + 0.15) = 5750
56. The equipment grounding conductor of a branch circuit shall be identified by what
color?
A. Green B. Black C. White D. Gray
57. In bathtub and shower areas no part of cord-connected fixtures, lighting track,
pendants or ceiling suspended (paddle) fans shall be located within a zone
measured _______ horizontally and ________ vertically from the top of the bathtub
rim or shower stall threshold.
A.1000mm, 3000mm
B. 600mm, 3000mm
C. 900mm, 2400mm
D. 800mm, 2500mm

121
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
58. What is the maximum operating temperature of type UF conductor?
A. 75 deg C B. 90 deg C C. 60 deg C D. 110 deg

59. Find the present worth with a total interest of P 5000 after two years at simple
interest rate of 6.25%.
A. P 35,000 B. P 25,000 C P 50,000 D. P 40,000
Solution:
𝐼 5000
I = Pin; P = 𝑖𝑛 = (0.0625)(2) = 40,000

60. Find the future amount of P 12,000 after 12 years with an interest rate of 9%
compounded annually.
A. P 33,752 B. P 34,896 C. P 32,649 D. P 31,625
Solution:

F = P (1 + i) 𝑛 = 12000(1 + 0.09)12 = 33752

61. Find the future amount of P 12,000 after 12 years with an interest rate of 9%
compounded semi-annually.
A. P 33,272 B. P 34,426 C. 34,512 D. 36,186
Solution:

P = ₱ 12,000 n =12 years m = 2 i = 9%

r 9
i   4.5%
m 2
F  P1  i 
n*m

F  12,0001  0.045
2*12

₱ 34,512

62. What is the temperature in deg C of 2 liters of water at 30 deg C after 500 calories of
heat have been added?
A. 35.70 B. 38 C. 30.25 D. 39.75
Solution:

m = 2L T = 30oC Q = 500cal

Q = mC∆t ; 500

2000*(TH – 30oC) = 30.25oC


122
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
63. A light pass from glass to water. If the index of refraction for glass is 1.54 and for
water is 1.33, compute the critical angle for this light to pass to glass.
A. 59.7 deg B. 45. 8 deg C. 67.4 deg D. 50.9 deg
Solution:

IRC =1.54 IRW = 1.33

IRw
sin  
IRc
 IRw 
  sin 1  
 IRc 
 1.33 
  sin 1  
 1.54 

𝜭 = 𝟓𝟗. 𝟕𝟑°

64. What is the corresponding rate of interest for 18% simple discount rate?
A. 20.85% B. 23.72% C. 22.64% D. 21.95%
Solution:

d = 18%

d
i
1 d
18%
i
1  18%

𝒊 = 𝟐𝟏. 𝟗𝟓%

65. Structural steel elements subjected to torsion develop


A. Tensile stress C. Shearing stress
B. Compressive stress D. Bending stress

66. A 300-g object slides 80cm along a horizontal tabletop. How much work is done in
overcoming friction between the object and the table if the coefficient of kinetic
friction is 0.20?
A. +0.74 J B. -0.74 J C. +0.47 J D. -0.47 J
Solution:

m = 300g = 0.3 kg kf = 0.2 L= 80 cm = 0.8m

𝑊 = 0.3 ∗ 9.81 = 2.943𝑁

123
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

𝑊 = 2.943 ∗ 0.8 ∗ 0.2𝑐𝑜𝑠(180𝑜)

𝑾 = −𝟎. 𝟒𝟕 𝑱

67. Compute the rational KE of a 25-kg wheel rotating at 6.0 rev/s if the radius of
gyration og the wheel is 22 cm.
A. 0.68 k J B. 0.86 k J C. 0.93 k J D. 0.39 k J

Solution:

m = 25 kg Ø = 6rev/sec r = 22 cm
2  6rev 2rad 
KE  25* 0.22  
1
* 
2  sec 1rev 
𝑲𝑬 = 𝟎. 𝟖𝟔 𝒌𝑱
68. The chief source of energy in the world today is
A. Coal B. Oil C. Natural gas D. Uranium

69. Which element is present in all organic compounds?


A. Oxygen B. Carbon C. Nitrogen D. Phosphorus

70. A substance that, when added to a solution, makes changing the pH of the solution
more difficult.
A. Catalyst B. Solute C. Solvent D. Butter

71. An object that has momentum must also have


A. Acceleration C. Kinetic Energy
B. Impulse D. Potential Energy

72. At the highest or lowest point of the moment diagram


A. Maximum shear occur C. Maximum moment is twice the shear
B. Shear is zero D. Shear is negative

73. An asset is purchased for 120000 pesos. It is estimated life is 10 years, after which it
will be sold for 12000. Find the depreciation for the second year using the sum-of-
the-years-digit method.
A. P18,400 B. P18,200 C. P17,673 D. P17,763
Solution:
(10+1)
Sum of years = 10 2

= 55
9
𝐷2 = (120000 − 12000)( ) = 𝟏𝟕𝟔𝟕𝟑
55
124
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
74. The chemical shorthand name for molybdenum is
A. Mo B. Mb C. Md D. Mn

75. Formula for magnesium nitrite


A. Mg2(NO2)2 B. Mg(NO2) C. Mg(NO2)2 D. Mg2 (NO2)3

76. A force causing a rise of liquid in tubes of small diameter


A. Cohesion B. Surface tension C. Capillarity D. Adhesion

77. In RA 9136, what is SGC stands for


A. Successor Generating Company
B. Successor Generation Company
C. Special Generating Company
D. Special Generation Company

78. In RA 9236, what is CREM stands for


A. Competitive Retail Electricity Market
B. Competitor Retail Electricity Market
C. Competitive Retail Energy Market
D. Competitor Retail Energy Market

79. During the takeoff roll, a Boeing 747 jumbo jet is accelerating at 4 m/sec^2. If it
requires 40 secs to reach takeoff speed, determine the takeoff speed.
A. 110 m/sec B. 120 m/sec C. 140 m/sec D. 160m/sec
Solution:

𝑉𝑡 = 𝑉𝑜 + 𝑎 ∗ 𝑡

𝑉𝑡 = 0 + (4) ∗ (40) = 𝟏𝟔𝟎𝒎/𝒔𝟐

80. If $ 10,000 is borrowed now at 6% interest, how much will remain to be paid after a $
3,000 payments is made four years from now?
A. $ 9,625 B. $ 9,725 C. $ 9,400 D. $ 9,835
Solution:

𝐹 = 𝑃(1 + 𝑖)𝑛 = 10,000(1 + 0.06)4 – 3,000 = $ 𝟗, 𝟔𝟐𝟒. 𝟕𝟕

81. A Carnot engine operates between reservoirs at 20 deg C and 200 deg C. If 10Kw of
power is produced, the rejected heat rate is nearest:
A. 26.3 k J/s B. 20.2 k J/s C. 16.3 k J/s D. 12 k J/s
Solution:
𝑄 𝑇𝐿
=
𝑃 𝑇𝐻−𝑇𝐶

125
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Q/(10*103)
20+273
=(200+273)−(20+273)

Q = 16.3 kJ

82. Calculate the molarity of a solution of a 0.0150 mol of NaCl in 50.0 g of water if the
solution has a density of 1.02 g/Ml.
A. 0.306 M B. 0.301 M C. 0.603 M D. 0.103 M
Solution:

0.015
=
0.015 × 48
⟦50 + 1000 × 1.02⟧

=0.301M

83. Article II of Code of Ethics for Electrical Engineers contains


A. SEC. 1 to 8 B. SEC. 1 to 7 C. SEC. 1 to 6 D. SEC. 1 to 9

84. Article IV, Rule ___. Requirements for examination as a REE


A. 14 B. 15 C. 16 D. 17

85. A man paid a 10% down payment of P 2,000,000 for a house and lot and agreed to
pay the balance on monthly installments for 5 years at an interest rate of 15%
compound monthly. What is the monthly installment in pesos?
A. 44,528.34 B. 42,821.87 C. 43,625.92 D. 45,825.65
Solution:

n = 5 years

r = 15%

m = 12

PTOT = 2,000,000
0.15
i= 12

= 1.25%

PDOWN = 2,000,000×0.1 = 200,000

P = 2,000,000 – 200,000 = 1,800,000

126
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
(1.25%)(1+0.0125)12(5)
A=⌊ (1+0.0125)12(5) −1

= ₱ 42,821.87

86. An automobile travelling at a speed of 30mph accelerates uniformly to a speed of


6omph in 10 sec. How far does the automobile travel during the time of
acceleration?
A. 880 ft. B. 660 ft. C. 770 ft. D. 990 ft.
Solution:

Vo = 30mph

Vf = 60mph

t = 60sec

5280𝑓𝑡 1ℎ𝑟
𝑉𝑜 = ( 30𝑚𝑖𝑙𝑒𝑠/ℎ𝑟)( )( ) = 44𝑓𝑡/𝑠
1𝑚𝑖𝑙𝑒 3600sec
5280𝑓𝑡 1ℎ𝑟
𝑉𝑓 = ( 60𝑚𝑖𝑙𝑒𝑠/ℎ𝑟 )( )( ) = 88𝑓𝑡/𝑠
𝑚𝑖𝑙𝑒 3600sec
88 + 44
𝑆 = ⌊ ⌋ × 10
2

∴ 𝑺 = 𝟔𝟔𝟎

87. During an isentropic expansion of air, the volume triples. If the initial temperature is
200 deg C, find T2 in deg C.
A. 32 B. 28 C. 16 D. 8
Solution:

11.4−1
(200 + 273) ( )= 304.8K
3

=304.8- 273

=32

88. If the pressure in a tank of oil (sp gr. = 0.80) is 400kPa, what is the equivalent head
in meters of water?
A. 50.97 B. 40.77 C. 59.70 D. 47.70
Solution:

127
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

400
𝐻𝑤 = = 𝟒𝟎. 𝟕𝟕
9.81
89. How many grams are these in 0.01 mole of Na2SO4?
A. 7.1 g B. 14.2 g C. 9.6 g D.1.42g
Solution:

0.01 mole

Na2SO4

Na = 23

S=32

O = 16

= [(23 ∗ 2) + 32 + (16 ∗ 4)] ∗ 0.01

∴ 𝟏. 𝟒𝟐𝒈

90. What rules are included in Article V of RA 7920?


A. RULE 1 to 10n B. RULE 11 to 20 C. RULE 21 to 27 D. RULE 28 to 34

91. What is the static head corresponding to a flow velocity of 10 ft/sec?


A. 1.55 ft B. 1.75 ft C. 2.05 ft D. 2.25 ft
Solution:

10𝑓𝑡
𝑉= 𝑠𝑒𝑐

(10)2
𝑉ℎ = = 𝟏. 𝟓𝟓𝒇𝒕
2(32.2)

92. Water flows through a long 0.5 in inside dimeter hose at 3gpm. Water velocity in fps
is nearest to:
A. 1 B. 5 C. 10 D. 20
Solution:

𝐷 = 0.5 𝑖𝑛, 𝑄 = 3 𝑔𝑝𝑚, 𝑟 = 0.0208𝑓𝑡

3.6𝑔𝑎𝑙 1𝑚𝑖𝑛 0.05𝑔𝑎𝑙 1𝑓𝑡 3 0.00668𝑓𝑡 3


𝑄= ∗ = ∗ =
𝑚𝑖𝑛 60𝑠𝑒𝑐 𝑠𝑒𝑐 7.480 𝑠
𝐴 = 𝜋(0.0208)2 = 1.3635 ∗ 10−3 𝑓𝑡 2
128
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS

0.00668
𝑣= = 𝟒. 𝟗𝟎𝟐 𝒇𝒑𝒔
1.3635 ∗ 10−3
93. A high velocity flow of gas at 800 ft/sec possesses kinetic energy nearest to which of
the following?
A. 1.03 BTU/lb B. 4.10 BTU/lb C. 9.95 BTU/lb D.12.8BTU/lb
Solution:

800𝑓𝑡
𝑣=
𝑠𝑒𝑐
1 1 8002 𝐽
𝐾𝐸 = ∗ 𝑚 ∗ 𝑣2 = ∗ = 9937.9
2 2 32.2 𝑙𝑏
𝐽 1𝐵𝑇𝑈 𝐾𝐸 𝑩𝑻𝑼
9937.9 ∗ ; = 𝟏𝟐. 𝟕𝟕
𝑙𝑏 778𝐽 𝑊 𝒍𝒃

94. How many months at an interest of 1 percent per month does money have to be
invested before it will double in value?
A. 59 B. 62 C. 70 D. 76\
Solution:

2 = 1(1+0.01)n ; n = 69.67 months

95. The phenomenon of melting under pressure and freezing again when the pressure is
reduced is known as
A. Sublimation B. Condensation C. Deposition D. Regelation

96. A single rivet is used to join two plates. If the diameter of the rivet is 20mm and the
load P is 30 k N, what is the average shearing stress developed in the rivet?
A. 61.95 MPa B. 165.2 MPa C. 41.3 MPa D. 82.6 MPa
Solution:

𝐷𝑟 = 21.5 𝑚𝑚; 𝑃 = 30,000 𝑁


𝑟 = 10.75 𝑚𝑚 = 0.01075 𝑚
𝐴 = 𝜋 ∗ (0.01075)2 = 3.63 ∗ 10−4 𝑚2
30 ∗ 1003
𝑆= = 𝟖𝟐. 𝟔 𝑴𝑷𝒂
3.63 ∗ 10−4

97. If a solid circular shaft of 1.25 in diameter is subject to a torque of 2500 lb-in causing
an angle of twist of 3.12 degrees in a 5 ft. length, determine the shear modulus of a
material.
129
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 10.6x10^6 psi B. 12.8x10^6 psi C. 11.5x10^6 psi D.9.3x10^6psi
Solution:

180°
𝜃 = 3.12° ∗ = 0.0544 𝑟𝑎𝑑
𝜋𝑟𝑎𝑑
(2500) ∗ (5𝑓𝑡 ∗ 12)
𝜃= = 𝟏𝟏. 𝟓 ∗ 𝟏𝟎𝟔 𝒑𝒔𝒊
(0.0544 ∗ 0.2397)

98. Which of the following cycle is used in vapor cycle power plant?
A. Brayton cycle B. Rankine Cycle C. Diesel cycle D. Ericson cycle

99. A simply supported beam of length 10 ft and rectangular cross section 1 in x 3 in


carries a uniform load of 200lb/ft. The beam is titanium, type Ti-5Al-2.55n, having a
yield strength of 115,000 psi and E = 16x10^6 psi.
A. 1.25 in B. 2.85 IN C. 1.00 in D. 2.05 in
Solution:

200𝑙𝑏
𝐿 = 10𝑓𝑡 ; 𝐴 = 1 𝑖𝑛 ∗ 3 𝑖𝑛; 𝑁 = ; 𝑌𝑠 = 115,000 𝑝𝑠𝑖; 𝐸 = 16 ∗ 106 𝑝𝑠𝑖
𝑓𝑡

5 ∗ (200) ∗ (10 ∗ 12)4


= = 𝟏. 𝟐𝟓 𝒊𝒏
3 2
384 ∗ (16 ∗ 106 ) ∗ (12)

100. What is the centripetal force required to cause a 3200-pound car to go around a
curve of 880-ft radius at a speed of 60mph?
A. 990 lb B. 880 lb C. 770 lb D.1100lb
Solution:

𝑚 = 3200 𝑙𝑏; 𝑟 = 880 𝑓𝑡; 𝑣 = 60 𝑚𝑝ℎ


3200
𝑊= = 99.38
32.2

(3200) ∗ (88)2
𝐹𝑐𝑝 = = 𝟖𝟕𝟒. 𝟓𝟑𝟏 𝒍𝒃
(32.2) ∗ (880)

130
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2015
ENGINEERING SCIENCES AND ALLIED SUBJECTS
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM AUGUST 2014

1. Determine the force necessary to accelerate a mass of 20 lbm. at a rate of 60


ft/sec^2 vertically upward.
A. 37.3 lbf B. 57.3 lbf C. 73.3 lbf D. 75.3 lbf

Solution:

𝐚 𝟔𝟎
𝐅 = 𝐦 (𝟏 + ) = 𝟐𝟎 (𝟏 + ) = 𝟓𝟕. 𝟐𝟔𝟕 𝐥𝐛𝐟
𝐠 𝟑𝟐. 𝟐

2. Momentum is closely related to


A. kinetic energy B. potential energy C. impulse D. power

3. In thermodynamics we focus our attention in which form of energy?


A. kinetic B. potential C. internal D. total

4. A machine an initial cost of P 50,000.00 and a salvage value of P 10,000.00 after 10


years. What is the book value after 5 years using straight line depreciation?
A. P 35,000.00 B. P 25,000.00
C. P 15,000.00 D.P 30,000.00

Solution:

𝟓(𝟓𝟎, 𝟎𝟎𝟎 − 𝟏𝟎, 𝟎𝟎𝟎)


𝐃𝐧 = = 𝐏𝟐𝟎, 𝟎𝟎𝟎
𝟏𝟎
𝐂𝐧 = 𝟓𝟎, 𝟎𝟎𝟎 − 𝟐𝟎, 𝟎𝟎𝟎 = 𝐏𝟑𝟎, 𝟎𝟎𝟎𝟎

5. An iceberg has a density of 917 kg/m^3. If float in fresh water, what percent of
iceberg’s volume will be viible?
A. 91.7% B. 8.3% C. 93.1% D. 6.9%

Solution:

𝟗𝟏𝟕
𝐕𝐝𝐢𝐬𝐩𝐥𝐚𝐜𝐞𝐝 = 𝐕 = 𝟎. 𝟗𝟏𝟕 𝐕𝐢𝐜𝐞𝐛𝐞𝐫𝐠
𝟏𝟎𝟎𝟎 𝐢𝐜𝐞𝐛𝐞𝐫𝐠
𝐕𝐞𝐱𝐩𝐨𝐬𝐞𝐝 = (𝟏 − 𝟎. 𝟗𝟏𝟕)𝐕𝐢𝐜𝐞𝐛𝐞𝐫𝐠 = 𝟎. 𝟎𝟖𝟑 = 𝟖. 𝟑%

6. The element that is practically insoluble in solid copper is known as


A. Lead B. Brass C. Boron D. Neon

𝒌𝒈
7. The standard pressure in meters of ammonia (𝝆 = 𝟔𝟎𝟎 𝒎𝟑 ) is:
A. 17 B. 19 C. 23 D. 31

8. A law which states that in a present fluid, the pressure exerted on it anywhere gets
transmitted in all directions.
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. Archimedes’ Law C. Darcy’s
B. Stoke’s Law D. Pascal’s Law

9. Steels that are used for axles, gears and similar parts requiring medium to high
hardness and high strength are known as
A. Low-carbon steels C. High-carbon steels
B. Medium-carbon steels D. Very high-carbon steels

10. The maximum moment induced in a simply supported beam of 20 foot span, by a
2,000 pound load at midspan is
A. 1,500 ft-lbs B. 15,000 ft-lbs
C. 30,000 ft-lbs D. 10,000 ft-lbs

Solution:
𝐏𝐋 (𝟐𝟎)(𝟐,𝟎𝟎𝟎)
𝐌𝐦𝐚𝐱 = = = 𝟏𝟎, 𝟎𝟎𝟎 𝐟𝐭 − 𝐥𝐛𝐬
𝟒 𝟒

11. A boy throws a ball with negligible air resistance. What happen to its acceleration?
A. Remains constant
B. Decelerate when the ball is going up and accelerated when going down
C. Increases
D. Decreases

12. Which is not a programming language?


A. FORTRAN B. LOTUS C. PASCAL D. COBOL
13. The units of joules can be converted to which of the following?
A. Pa-m^2 B. N-kg C. Pa/m^2 D. Pa-m^3

Solution:
𝐍 𝐍 𝐍
(𝐏𝐚 = 𝐦𝟐 ) 𝐦𝟑 ; 𝐏𝐚(𝐦𝟑 ) = 𝐦 ; 𝐉 = 𝐦 = 𝐏𝐚 − 𝐦𝟑

14. When two bodies isolated from other environment, are in thermal equilibrium with a
third body, the two are in thermal equilibrium with each other. What do you call does
statement?
A. Zeroth Law of Thermodynamics
B. First Law of Thermodynamics
C. Second Law of Thermodynamics
D. Third Law of Thermodynamics

15. It is a mixture of two or more non-volatile liquids in which separation takes place very
slowly.
A. suspension B. solution C. colloids D. emulsion

16. The purpose of copper in steel alloying is to increase


A. Atmospheric corrosion resistance
133
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
B. Hardness and strength
C. Corrosion resistance
D. Deoxidation

17. The unit lighting for a dwelling unit expressed in watts per square meter shall be
A. 8 watts B. 16 watts C. 24 watts D. 40 watts

18. A certain dam with height h and width w. Find force.


A. F=0.5 pgh B. F=pgh
C. F=pgw^2h D. F=pgwh^2

19. The study of mechanics of fluids which deals with velocities and streamlines without
considering forces or energy
A. kinematics B. hydrostatics C. hydrodynamics D. hydrology

20. A carnot refrigerator requires 10 kW to remove 20 kJ/s from a 20 deg C reservoir.


What is 𝑻𝑯 ?
A. 440 K B. 400 K C. 360 K D. 340 K

21. A beam with a rectangular cross-seciton with breath of 20 cm. Determine the depth
of the beam if the maximum shearing stress is 30 kg/cm^2 and Vmax = 10,000 kg.
A. 25 cm B. 23 cm D. 20 cm D. 30 cm

Solution:

𝟐𝟎 𝟏𝟎, 𝟎𝟎𝟎
𝐡= ( ) = 𝟎. 𝟐𝟓 𝐜𝐦
𝟑𝟎 𝟐𝟔, 𝟔𝟔𝟔. 𝟔𝟕

22. (14) base 10 = ( ) base 2


A. 1100 B. 1011 C. 1110 D. 1001

Solution:

2 14 0
2 7 1
2 3 1
1

∴ 𝟏𝟏𝟏𝟎𝟐

23. BIOS stands for


A. Basic Input Output Society
B. Basic Input Output System
C. Base Input Output Society
D. Base Input Output System

134
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
24. If you borrowed P 10,000 from a bank with 18% interest per annum. What is the total
amount to be paid after one year?
A. P 11,800 B. 12, 800 C. P 5,400 D. P 6,400

Solution:
𝐅 = 𝐏(𝟏 + 𝐢)𝐧 = 𝟏𝟎, 𝟎𝟎𝟎(𝟏 + 𝟎. 𝟏𝟖)𝟏 = 𝐏 𝟏𝟏, 𝟖𝟎𝟎

25. When will an amount be tripled with an interest of 11.56%


A. 9.80 years B. 10.04 years
C. 10.54 years D. 11.03 years

Solution:

𝐅 = 𝐏(𝟏 + 𝐢)𝐧 = 𝟑𝐏
𝟑𝐏 = 𝐏(𝟏 + 𝟎. 𝟏𝟏𝟓𝟔)𝐧
𝐥𝐧 𝟑 𝐧𝐥𝐧𝟏. 𝟏𝟏𝟓𝟔
= ; 𝐧 = 𝟏𝟎. 𝟎𝟒𝟑 𝐲𝐫𝐬
𝐥𝐧 𝟏. 𝟏𝟏𝟓𝟔 𝐥𝐧𝟏. 𝟏𝟏𝟓𝟔
26. What is the S.I. unit of pressure?
A. Dyne-cm B. Pascal C. Bar D. kg/cm^2

27. 1+1 in binary is


A. 2 B. 11 C. 10 D. 110

Solution:

𝟏𝟐
𝐈𝟐 +
𝟏𝟎𝟐

28. What is the form of momentum diagram of beam supported of both ends without
external load?
A. Triangle B. Linear C. Circular D. Parabola
B.
29. What is the smallest unit of information handled by a computer?
A. Bit B. Byte C. Cell D. Character

30. A byte is composed of how many bits?


A. 2 B. 4 C. 6 D. 8

31. Determine the length of the shortest 2mm diameter bronze wire which can be
twisted through two complete turns without exceeding a shearing stress of 70 MPa.
Use G=35 Gpa.
A. 5640 mm B. 5460 mm C. 6380 mm D. 6280 mm

Solution:

135
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐓𝐋 𝐓𝐋 𝟏𝟔𝐓 𝟏𝟔𝐓
𝛉= ; 𝟒𝛑 = ; 𝛔= 𝟑
; 𝟕𝟎𝐱𝟏𝟎𝟔 = ; 𝐓 = 𝟎. 𝟏𝟎𝟗𝟗𝟔𝐍 − 𝐦
𝐉𝛉 𝐉𝐆 𝛑𝐃 𝛑(𝟐𝐱𝟏𝟎−𝟑 )𝟑
(𝟎. 𝟏𝟎𝟗𝟗𝟔)𝐋
𝟒𝛑 = 𝛑
(𝟐𝐱𝟏𝟎−𝟑 )𝟒 (𝟑𝟓𝐱𝟏𝟎𝟗 )
𝟑𝟐
𝑳 = 𝟔𝟐𝟖𝟐. 𝟒 𝒎𝒎

32. In thermodynamics our attention is focused on which form of energy?


A. Kinetic Energy B. Internal Energy
C. Potential Energy D. Total Energy

33. If the pressure in a tank of oil (S.G.=0.80 ) is 400 kPa, what is the equivalent head in
meters of water?
A. 50.97 B. 40.77 C. 30.87 D. 60.57

Solution:
𝑯𝒘𝒂𝒕𝒆𝒓 = (𝑺𝒐𝒊𝒍 )(𝑯𝒐𝒊𝒍 )
𝝆 𝝆 𝟒𝟎𝟎
𝑯𝒘𝒂𝒕𝒆𝒓 = 𝜸 = 𝑺 𝜸 = 𝟎.𝟖𝟎(𝟗.𝟖𝟏) = 𝟓𝟎. 𝟗𝟕 𝒎
𝒐𝒊𝒍 𝒐𝒊𝒍 𝒘𝒂𝒕𝒆𝒓
𝑯𝒘 = (𝑺𝒐𝒊𝒍 )(𝑯𝒐𝒊𝒍 ) = (𝟎. 𝟖)(𝟓𝟎. 𝟗𝟕 𝒎)
∴ 𝑯𝒘 = 𝟒𝟎. 𝟕𝟕
34. A loan that is discharged or repaid by a uniform series of payments extending over
its duration is said to be
A. funded B. depreciated
C. amortized D. bonded

35. Which of the following engines is the most efficient?


A. gasoline engine B. diesel engine
C. gas turbine D. carnot engine

36. A branch of hydraulics which deals with the study of pure motion in liquids.
A. hydrology B. hydrokinetics
C. hydrostatic D. hydrodynamics

37. When exposed to the atmosphere, which of the following liquids is coldest?
A. Oxygen B. nitrogen C. hydrogen D. helium
38. A company deposits $ 1000 every year for ten years in a bank. The company makes
no deposits during the subsequent five years. If the bank pays 8% interest. The
amount in the account at the end of 15 years is nearest to
A. $ 10,800 B. $15,000 C. $ 16,200 D. $ 21,200

Solution:

𝟏−(𝟏+𝐢)−𝐧 𝟏−(𝟏+𝟎.𝟎𝟖)−𝟏𝟎
𝐏 = 𝐀[ ] (𝟏 + 𝐢)𝐦 = 𝟏𝟎𝟎𝟎 [ ] (𝟏 + 𝟎. 𝟎𝟖)𝟏𝟓 = 𝐏 𝟐𝟏, 𝟐𝟖𝟓. 𝟓𝟏
𝐢 𝟎.𝟎𝟖

39. The abbreviation for a binary digit.

136
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. bid B. bin C. bit D. byte

40. For REE board examination, the passing general average is 70% provided there is
no grade below ____ in of the 3 subjects.
A. 50% B. 60% C. 65% D. 40%

41. A steel support must connect two 30,000 pound tensile loads separated by 200
inches. The maximum allowable stress is 10,000 psi and the maximum allowable
elongation is 0.02 inch. What is the required area? (E= 30x10^6 psi)
A. 10 sq. in. B. 20 sq. in. C. 30 sq. in. D. 40 sq. in.

Solution:

𝐏𝐋 𝐏𝐋 𝟑𝟎𝟎𝟎𝟎(𝟐𝟎𝟎)
𝛅= ; 𝐀= = = 𝟏𝟎 𝐢𝐧𝟐
𝐀𝐄 𝛅𝐄 𝟎. 𝟎𝟐(𝟑𝟎𝐱𝟏𝟎𝟔 )

42. Newton’s first law is of the referred to as which of the following?


A. The law of straight-line method
B. The law of momentum
C. The law of inertia
D. F = ma

43. If $ 10,000 is borrowed now at 6% interest, how much will remain to be paid after a
$3,000 payment is made four years from now?
A. $9,400 B. $7,000 C. $9,725 D. $9,625

Solution:
𝑭 = 𝑷 (𝟏 + 𝒊)𝒏 − 𝑰
𝑭 = 𝟏𝟎, 𝟎𝟎𝟎(𝟏 + 𝟎. 𝟎𝟔)𝟒 − 𝟑𝟎𝟎𝟎
∴ 𝑭 = 𝟗, 𝟔𝟐𝟓

44. A ball is thrown so that it just clears a 3 m fence 18 m away. If it left the hand 1.5 m
above the ground and at an angle of 60 degrees with the horizontal, what was the
initial velocity of the ball?
A. 16.44 m/s B. 14.64 m/s C. 12.24 m/s D. 21.24 m/s

Solution:
𝟏
𝑹𝒂𝒏𝒈𝒆 = 𝑽𝒐 𝐜𝐨𝐬 𝜽 𝒕 𝒉 = 𝒉𝒐 + 𝑽𝒐 𝐬𝐢𝐧 𝜽 𝒕 + 𝟐 𝒈𝒕𝟐
𝟏
𝟏𝟖 = 𝑽𝒐 𝐜𝐨𝐬 𝟔𝟎 𝒕 𝟏𝟔𝟓 = 𝟏𝟓 + 𝟑𝟏. 𝟏𝟕𝟕 − (𝟗. 𝟖𝟏)𝒕𝟐
𝟐
𝑽𝒐 𝒕 = 𝟑𝟔 𝒎 𝒕𝟐 = 𝟔. 𝟎𝟓 ; 𝒕 = 𝟐. 𝟒𝟔𝟎
𝑽𝒐 𝐬𝐢𝐧 𝟔𝟎 𝒕 = 𝑽𝒐 𝐬𝐢𝐧 𝟔𝟎 𝑽𝒐 𝒕 = 𝟑𝟔 𝒎
𝟑𝟔 𝒎
𝑽𝒐 𝐬𝐢𝐧 𝜽 𝒕 = 𝟑𝟏. 𝟏𝟕𝟕 𝒎 𝑽𝒐 = 𝟐.𝟒𝟔𝟎 = 𝟏𝟒. 𝟔𝟑𝟒 𝒎⁄𝒔

45. Determine the moment of inertia of an equilateral triangle 6 in on a side about an


axis through its centroidal and parallel to the base.
137
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 32.4ln^4 B. 23.4 in^4 C. 64.8 in^4 D. 46.8 in^4

Solution:
𝒉𝟐 = 𝟔𝟐 − 𝟑𝟐
𝟑
𝒉 = √𝟑𝒊𝒏
𝟑 𝟑
𝒃𝒉𝟑 𝟔( √𝟑𝒊𝒏)
𝑰𝑪 = =
𝟑𝟔 𝟑𝟔
∴ 𝑰𝑪 = 𝟐𝟑. 𝟒 𝒊 𝒏𝟒

46. A market condition where there are two buyers and two sellers is called______
A. Duopoly C. bilateral oligopoly
B. duopsony D. bilateral duopoly

47. A person buys a piece of property for P100,000 downpayment and ten deferred
semi-annual payments of P8,000 each starting three years from now. What is the
present value of the investment if the rate of interest is 12% compounded semi-
annually?
A. P144,000 B. P192,000 C. P148,500 D. P185,000

Solution:
𝑨[(𝟏+𝒊)𝒏 −𝟏]
𝑷𝟏 = (𝟏+𝒊)𝒏 𝒊
𝟖𝟎𝟎𝟎[(𝟏+𝟎.𝟎𝟔)𝟏𝟎 −𝟏]
𝑷𝟏 = (𝟏+𝟎.𝟎𝟔)𝟏𝟎 (𝟎.𝟎𝟔)
= 𝟓𝟖, 𝟖𝟖𝟎. 𝟔𝟗
𝑷𝟏 = 𝑷𝟐 ((𝟏 + 𝒊)𝒏 )
𝟓𝟖, 𝟖𝟖𝟎. 𝟔𝟗 = 𝑷𝟐 ((𝟏 + 𝟎. 𝟎𝟔)𝟓 )
𝑷𝟐 = 𝟒𝟑, 𝟗𝟗𝟗. 𝟎𝟕𝟔

𝑻𝒐𝒕𝒂𝒍 𝒂𝒎𝒐𝒖𝒏𝒕 = 𝟏𝟎𝟎, 𝟎𝟎𝟎 + 𝑷𝒂

𝑻𝒐𝒕𝒂𝒍 𝒂𝒎𝒐𝒖𝒏𝒕 = 𝟏𝟎𝟎, 𝟎𝟎𝟎 + 𝟒𝟑, 𝟗𝟗𝟗. 𝟎𝟕𝟔 = 𝟏𝟒𝟒, 𝟎𝟎𝟎

48. If a flea can jump straight up to a height of 0.440 m, what is its initial speed as it
leaves the ground?
A. 2.89 B. 2.98 C. 2.94 D. 2.49

Solution:
𝐯 = √𝟐𝐠𝐡 = √𝟐(𝟗. 𝟖𝟏)(𝟎. 𝟒𝟒𝟎) = 𝟐. 𝟗𝟑𝟖 𝐦/𝐬

49. An electric fan is turned off, and its angular velocity decreases uniformly from 500
rpm to 200 rpm in 4.0 s. Find the number of revolutions made by the motor in the 4-s
interval.
A. 43. 2 rev B. 52.3 rev C. 32.2 rev D. 23.3 rev

Solution:

138
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝝎𝒛 = 𝝎𝒐𝒛 + 𝝎𝒓𝒕

(𝟐𝟎𝟎 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) = (𝟓𝟎𝟎 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) + 𝒂𝒛 (𝟒. 𝟎𝟎𝟓)


𝟏 𝒎𝒊𝒏 𝟏 𝒎𝒊𝒏
(𝟐𝟎𝟎 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) ( ) = (𝟓𝟎𝟎 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) (𝟔𝟎 𝒔𝒆𝒄) + 𝒂𝒛 (𝟒. 𝟎𝟎𝟓)
𝟔𝟎 𝒔𝒆𝒄

𝟏 𝒎𝒊𝒏
(𝟑. 𝟑𝟑 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) = (𝟖. 𝟑𝟑 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 ) ( ) + 𝒂𝒛 (𝟒. 𝟎𝟎𝟓)
𝟔𝟎 𝒔𝒆𝒄

𝒂𝒛 = 𝟏. 𝟐𝟓 𝒓𝒆𝒗 − 𝒔𝒆𝒄−𝟏
𝟏
𝜽 − 𝜽𝟎 = 𝒂𝒛𝒐 𝒕 + 𝒂𝟐 𝒕𝟐
𝟐

𝟏
𝜽 − 𝜽𝟎 = (𝟖. 𝟑𝟑 𝒓𝒆𝒗 − 𝒎𝒊𝒏−𝟏 )(𝟒. 𝟎𝟎𝟓) + (𝟏. 𝟐𝟓 𝒓𝒆𝒗 − 𝒔𝒆𝒄−𝟏 )(𝟒. 𝟎𝟎𝟓)
𝟐

∴ 𝜽 = 𝟐𝟑. 𝟑 𝒓𝒆𝒗

50. Calculate the polar moment of inertia J of a 75 mm-diameter solid circular shaft.
A. 𝟑. 𝟏𝐀. 𝐱𝟏𝟎𝟔 𝐦𝐦𝟒 B. 𝟏. 𝟑𝐱𝟏𝟎𝟔 𝐦𝐦𝟒
C. 𝟐. 𝟏𝐱𝟏𝟎𝟔 𝐦𝐦𝟒 D. 𝟏. 𝟐𝐱𝟏𝟎𝟔 𝐦𝐦𝟒

Solution:
𝛑𝐃𝟒 𝛑(𝟕𝟓)𝟐
𝐉= = = 𝟑. 𝟏𝟎𝟔𝐱𝟏𝟎^𝟔𝐦𝐦^𝟒
𝟑𝟐 𝟑𝟐

51. The theoretical velocity generated by a 10-foot hydraulic head is


A. 12.2 ft/sec B. 17.9 ft/sec C. 25.4 ft/sec D. 29.2 ft/sec

52. The element that was discovered between calcium and titanium is ____________
A. Silicon B. Scandium C. Molybdenum D. Potassium

53. A tank has a gauge pressure of 500 mmHg vacuum. Find the pressure in kPa
gauge? Use a conversion factor from mmHg to Pa (Pascal = N/sq. m.) is 133.4
A. 66.7 kPa B. 70 kPa C. -66.7 kPa D. -70 kPa

Solution:
𝟏𝟎𝟏.𝟑𝟐𝟓 𝐤𝐏𝐚
−𝟓𝟎𝟎 𝐦𝐦𝐇𝐠 𝐱 = −𝟔𝟔. 𝟔𝟔 𝐤𝐏𝐚
𝟕𝟔𝟎 𝐦𝐦𝐇𝐠

54. Which gate is formed by inverting the output of the AND gate?
A. NAND gate B. OR gate C. NOR gate D. None of these

55. Any equipment which produces, modifies, regulates, or controls the supply of electric
energy is the___________________________
A. “Electric Supply Equipment C. ”Substation”
B. “Transformer” D. “Generator Set”

139
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
56. RA 7920, Rule 2 (d) defining?
A. CHED B. Commission C. Board of EE D. TESDA

57. What is the article V of Code of Ethics for Electrical Engineers?


A. Professional Life C. Effectivity
B. Penal Provisions D. Relations with Client and Employer

58. The best method used to refine gold metal is


A. Bassemerization C. Distillation
B. Oxidation D. Electrolysis
A
59. The force required to start a mass of 50 kg moving across a rough surface is 343 N.
What is the coefficient of starting friction?
A. 0.70 B. 0.80 C. 1 D. 0

Solution:
𝐅 𝟑𝟒𝟑 𝐦
𝐅 = 𝐦𝐚; 𝐚 = = = 𝟔. 𝟖𝟔 𝟐
𝐦 𝟓𝟎 𝐬
𝐚 𝟔. 𝟖𝟔
𝛍= = = 𝟎. 𝟕𝟎
𝐠 𝟗. 𝟖𝟏

60. An object that has momentum must also have


A. Acceleration B. impulse C. kinetic energy D. potential energy

61. The Hooke’s law hold good within


A. Yield point B. elastic limit C. plastic limit D. Euler’s limit

62. At 6%, find the capitalized cost of a bridge whose cost is P 250M and the life is 20
years, if the bridge must be partially paid at a cost of P 100M at the end of each 20
years.
A.P 295.31M C. P 264.82 M
B. P 259.31 M D. P 248.82 M

Solution:

𝐎𝐌 𝐑𝐂 − 𝐒𝐕 𝟏𝟎𝟎 − 𝟎
𝐤 = 𝐅𝐂 + + 𝐧
= 𝟐𝟓𝟎 + 𝟎 + = 𝐏𝟐𝟗𝟓. 𝟑𝟎𝟖𝐌
𝐢 (𝟏 + 𝐢) − 𝟏 (𝟏 + 𝟎. 𝟎𝟔)𝟏𝟎 − 𝟏

63. Two 100-mm diameter are connected by means of two flanges with 20-mm diameter
bolts equally spaced on a circle of 20 cm diameter. If the maximum shear in the
shaft due to torque is not to exceed 80 Mpa and average shear strength of the bolts
is not to be exceed 60 MPa for the same torque, determine the number of bolts
required.
A. 7 B. 8 C. 9 D. 10

Solution:
140
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝟏𝟔𝑻
𝝉 = 𝝅𝑫𝟑
𝟏𝟔𝑻
𝟖𝟎𝒙𝟏𝟎𝟔 = 𝟏𝟎𝟎 𝟑
𝝅( )
𝟏𝟎𝟎𝟎
𝑻 = 𝟓𝟎𝟎𝟎𝝅𝑵 ∙ 𝒎
𝑻 = 𝑹𝑨𝑩𝒐𝒍𝒕𝒔 𝑵𝝉
𝟐𝟎 𝝅 𝟐
𝟓𝟎𝟎𝟎𝝅 = ( ) ( ) (𝟐𝟎⁄𝟏𝟎𝟎𝟎) (𝑵)(𝟔𝟎𝒙𝟏𝟎𝟔 )
(𝟐𝟎)(𝟏𝟎𝟎) 𝟒
𝑵 = 𝟖. 𝟑𝟑𝟑 → 𝒎𝒖𝒔𝒕 𝒃𝒆 𝒂𝒏 𝒉𝒊𝒈𝒉𝒆𝒓 𝒊𝒏𝒕𝒆𝒈𝒆𝒓
∴𝑵=𝟗
64. A spring whose force constant is k is cut in half. Each of the new springs has a force
constant of
A. k/2 B. k C. 2k D. 4k

65. Light scattered perpendicularly to an incident beam is partly


A. diffracted B. polarized C. monochromatic D. coherent

66. RA 9136 has four sectors, which of the following is not included?
A. supply C. generation
B. distribution D. system operation

67. (100) base 10+(111) base 2 = (___) base 8.


A. 151 B. 153 C. 145 D. 105

68. Galvanized steel product s are coated with ______________.


A. Carbon B. Sulfur C. Zinc D. Nickel

69. What is PDC stands for EPIRA?


A. Philippine Distribution Commision C. Philippine Distribution Committee
B. Philippine Distribution Code D. Philippine Distribution Coordination

70. It is the term used to describe the complete process of bringing a new product or
service to market.
A. Design C. Sales encouragement
B. Sourcing D. Product development

71. The following forces act on an object: 10 N to the north, 20 N to the southeast, and
5N to the west. The magnitude of their resultant is.
A. 5N B. 10N C. 13N D. 23N

Solution:
𝒇𝒐𝒓 𝑺𝒐𝒖𝒕𝒉 𝑫𝒊𝒓𝒆𝒄𝒕𝒊𝒐𝒏:
𝒀𝒂𝒙𝒊𝒔 = 𝟏𝟎 − 𝟐𝟎 𝐜𝐨𝐬 𝟒𝟓° = 𝟒. 𝟏𝟒𝟐
𝒇𝒐𝒓 𝑬𝒂𝒔𝒕 𝑫𝒊𝒓𝒆𝒄𝒕𝒊𝒐𝒏:
𝑿𝒂𝒙𝒊𝒔 = 𝟐𝟎 𝐜𝐨𝐬 𝟒𝟓° − 𝟓 = 𝟗. 𝟏𝟒𝟐

141
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑼𝒔𝒊𝒏𝒈 𝑷𝒚𝒕𝒉𝒂𝒈𝒐𝒓𝒆𝒂𝒏𝒔 𝒕𝒐 𝒔𝒐𝒍𝒗𝒆 𝒇𝒐𝒓 𝑹:
𝑹 = √𝑿𝟐 + 𝒀𝟐
𝑹 = √𝟗. 𝟏𝟒𝟐𝟐 + 𝟒. 𝟏𝟒𝟐𝟐 = 𝟏𝟎. 𝟎𝟑𝑵 ≈ 𝟏𝟎𝑵
72. A car undergoes a constant acceleration of 6.0 m/s^2 starting from rest. In the first
second it travels
A. 3m B. 6m C. 18m D. 36m

Solution:
𝟏
𝑺 = 𝑽𝑶 + 𝟐 𝒂𝒕𝟐
𝒎 𝟏 𝒎
𝑺 = (𝟎 ) (𝟏 𝒔𝒆𝒄) + 𝟐 (𝟔 ) (𝟏𝒔)𝟐
𝒔 𝒔𝟐
∴ 𝑺 = 𝟑. 𝟎 𝒎

73. The mass of 8 lb of pineapples is


A. 0.25 slug B. 0.5 slug C. 4 slugs D. 256 slugs

Solution:
𝟏𝐤𝐠 𝟏 𝐬𝐥𝐮𝐠
𝟖 𝐥𝐛 𝐱 𝐱 = 𝟎. 𝟐𝟒𝟗 𝐬𝐥𝐮𝐠
𝟐. 𝟐𝐥𝐛 𝟏𝟒. 𝟓𝟗 𝐤𝐠

74. The amount of work a 0.60-kW electric drill can do in 1.0 min is
A. 0.6 J B. 0.6 kJ C. 36 J D. 36 Kj

Solution:
𝐖 = 𝐏𝐭 𝐭 = 𝟏 𝐦𝐢𝐧 = 𝟔𝟎 𝐬
𝐉
𝐖 = 𝟎. 𝟔𝟎𝐱𝟏𝟎𝟑 𝐱𝟔𝟎 𝐬 = 𝟑𝟔𝟎𝐱𝟏𝟎𝟑 𝐉
𝐬

75. A 5 kg cart accelerates at 3 m/s^2 for 4 seconds. Aafter this time, what is its kinetic
energy?
A. 22.5 J B. 180 J C. 720 J D. 360 J

Solution:
𝐦
𝐕𝐟 = 𝐚𝐭 = (𝟑)(𝟒) = 𝟏𝟐
𝐬
𝟏 𝟏
𝐊𝐄 = 𝐦𝐯 𝟐 = (𝟓)(𝟏𝟐)𝟐 = 𝟑𝟔𝟎 𝐉
𝟐 𝟐

76. The thermodynamic statement of the conservation of energy of a system is the


A. first law B. second law C. third law D. zeroth law

77. What is the new volume of 20 liters of gas at STP which experiences a pressure
increased of 2 atm and temperature increases of 75 deg C?
A. 6.8 liters B. 8.5 liters C. 7.9 liters D. 5.6 liters

Solution:
142
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐏𝟏 𝐕𝟏 𝐏𝟐 𝐕𝟐 𝐏𝟏 𝐕𝟏 𝐓𝟐 (𝟏 𝐚𝐭𝐦)(𝟐𝟎𝐋)(𝟕𝟓 + 𝟐𝟕𝟑°𝐊)
= ; 𝐕𝟐 = = = 𝟖. 𝟒𝟗𝟖 𝐥𝐢𝐭𝐞𝐫𝐬
𝐓𝟏 𝐓𝟐 𝐓𝟏 𝐏𝟐 (𝟐𝟕𝟑°𝐊)(𝟏 + 𝟐𝐚𝐭𝐦)

78. A carwash area is classifies as


A. Wet location B. dry location C. damp location D. moist location

79. Motors must be labeled with the following nameplate rating, manufacturer’s name
and etc. This is
A. Manufacturing rule C. Wiring design rule
B. Construction rule D. installation rule

80. In sizing of wire, this is:


A. Manufacturing rule C. Wiring design rule
B. Construction rule D. installation rule

81. “Heavy water” has a mass of


A. 12 B. 18 C. 20 D. 36

82. The first period contains how many electrons?


A. 2 B. 4 C. 6 D. 8

83. Which of the following would be considered a system rather than a control volume?
A. A pump B. A tire C. A pressure cooker D. A turbine

84. How many grams are there in 0.01 mole of 𝑵𝒂𝟐 𝑺𝑶𝟒 ?
A. 7.1 g B. 14.2 g C. 9.6 g D. 1.42 g

Solution:
𝑵𝒂 = 𝟐𝟐. 𝟗𝟖𝟗𝟕𝟕𝟎 (𝟐) = 𝟒𝟓. 𝟗𝟕𝟗𝟓𝟒
𝑺 = 𝟑𝟐. 𝟎𝟔𝟓 (𝟏) = 𝟑𝟐. 𝟎𝟔𝟓
𝑶 = 𝟏𝟓. 𝟗𝟗𝟗𝟒 (𝟒) = 𝟔𝟑. 𝟗𝟗𝟕𝟔
𝒈
𝒈𝒓𝒂𝒎𝒔 = 𝟏𝟒𝟐. 𝟎𝟒𝟐𝟏𝟒 ⁄𝒎𝒐𝒍 𝒙 𝟎. 𝟎𝟏 𝒎𝒐𝒍 = 𝟏. 𝟒𝟐 𝒈

85. A capillary tube of internal radius 0.25 mm is dipped into water of surface tension 72
dynes/cm. How high does the water rise in the tube?
A. 5.46 cm B. 5.88 cm C.5.36 cm D. 5.97 cm

Solution:
𝟕𝟐𝐝𝐲𝐧𝐞𝐬 𝟏𝟎−𝟓 𝐍 𝟏𝟎𝟎 𝐜𝐦
𝟒( )( )( )
𝐜𝐦 𝟏 𝐝𝐲𝐧𝐞 𝟏𝐦
𝐡= = 𝟎. 𝟎𝟓𝟖𝟕 𝐦 𝐨𝐫 𝟓. 𝟖𝟕 𝐜𝐦
𝟗𝟖𝟏𝟎(𝟓𝐱𝟏𝟎−𝟒 )

86. The particle inside the nucleus is called


A. Nucleic B. Nuclons C. Nucleons D. nuclei

143
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
87. What is the change in entropy of a gas if the temperature increases from 100 K to
101 K when heat is added and the volume is kept constant?
A. 0.250 J/mole-K B. 0.125 J/mole-K
C. 0.375 J/mole-K D. 0.025 J/mole-K

Solution:
𝟏𝟎𝟏 𝑱
𝑺 = 𝟏𝟐. 𝟓𝟕 𝒍𝒏 (𝟏𝟎𝟎) = 𝟎. 𝟏𝟐𝟓 ⁄𝒎𝒐𝒍 ∙ 𝑲

88. What is the molarity of the solution if 150 g of KCI is dissolved in water to make 800
ml of solution?
A. 2.51 M B. 2.25 M C. 2.87 M D. 1.53 M

Solution:
𝟏 𝒎𝒐𝒍𝒆 𝑲𝑪𝑳
(𝟏𝟓𝟎 𝒈 ) ( ) = 𝟐. 𝟎𝟏 𝒎𝒐𝒍𝒆 𝑲𝑪𝑳
𝟕𝟒.𝟓𝟓 𝑮
𝟏𝟎𝟑 𝒎𝒍 𝟐.𝟎𝟏 𝒎𝒐𝒍𝒆 𝑲𝑪𝑳
(𝟏. 𝟎 𝑳) ( )( ) = 𝟐. 𝟓𝟏 𝑴
𝟏𝑳 𝟖𝟎𝟎 𝒎𝒍

89. A combine 9.3’ of water, 6.5’ of oil (SG = 0.71), and 5.0’ of air at 26 psig and 70 deg
F. What is the absolute pressure at the bottom of the container?
A. 47.637 psia B. 46.377 psia C. 43.767 psia D. 46.737 psia

Solution:
𝑷𝑻 = 𝑷𝟏 + 𝑷𝟐 + 𝑷𝟑 + ⋯ 𝑷𝑵
𝑷𝑻 = 𝜸𝟏 𝒉𝟏 + 𝜸𝟐 𝒉𝟐 + 𝑷𝟑
𝟔. 𝟓 𝟗. 𝟑 𝟏𝟎𝟏. 𝟑𝟐𝟓
𝑷𝑻 = (𝟗. 𝟖𝟏) ( ) (𝟎. 𝟕𝟏) + 𝟗. 𝟖𝟏 ( ) + 𝟐𝟔 [ ]
𝟑. 𝟖 𝟑. 𝟐𝟖𝟎𝟖 𝟏𝟒. 𝟕
𝑷𝒈 = 𝟐𝟐𝟎. 𝟖𝟐 𝒌𝑷𝒂𝒈
𝑷𝒂𝒃𝒔 = 𝑷𝒈 + 𝑷𝒂𝒕𝒎
𝑷𝒂𝒃𝒔 = 𝟐𝟐𝟎. 𝟖𝟐 + 𝟏𝟎𝟏. 𝟑𝟐𝟓
𝑷𝒂𝒃𝒔 = 𝟑𝟐𝟐. 𝟏𝟒𝟕 𝒌𝑷𝒂𝒂

𝟏𝟒. 𝟕 𝑷𝒔𝒊𝒂
𝑷𝒂𝒃𝒔 = 𝟐𝟐𝟎. 𝟖𝟐 + 𝟏𝟎𝟏. 𝟑𝟐𝟓𝟑𝟐𝟐. 𝟏𝟒𝟕 𝒌𝑷𝒂𝒂 ( )
𝟏𝟎𝟏. 𝟑𝟐𝟓 𝒌𝑷𝒂𝒂
𝑷𝒂𝒃𝒔 = 𝟒𝟔. 𝟕𝟑𝟔 𝒑𝒔𝒊𝒂

90. Give the formula for magnesium carbonate


A. 𝐌𝐀. 𝐠𝐂𝐎𝟑 B. 𝐌𝐠𝐂𝐎𝟐 C. 𝐌𝐠𝐂𝐎 D. 𝐌𝐠 𝟐 𝐂𝐎𝟑
B.
91. Cables for 220 kV lines are invariably?
A. Mica insulated C. Paper insulated
B. Compressed oil or compress gas D. Rubber insulated

92. What group of steels are high-carbon, high-chromium tools steels suitable for cold
working applications?
A. Group A B. Group D C. Group H D. Group M
144
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS

93. Which of the following phenomenon cannot take place with sound waves?
A. Interference B. Polarization C. Diffraction D. Reflection

94. The ore from which iron is obtained is


A. Sphalerite B. Bauxite C. Taconite D. Chalocite

95. The Electrical Engineer shall have observe such system of_______ principles and
values as a set of dynamic standards to guide his conduct and way of life. It is his
duty to practice profession according to ethics.
A. Dignity B. Moral C. Basic D. Engineering

96. What is the energy of a photon of wavelength 0.1 nanometer?


A. 2.2x10^-42 J B. 9.8x10^-26 J
C. 6.62x10^-24 J D. 1.99x10^-15 J

Solution:
𝐜 𝟑𝐱𝟏𝟎𝟖
𝐟= = = 𝟑𝐱𝟏𝟎𝟖 ; 𝐄 = 𝐡𝐟 = 𝟔. 𝟔𝟑𝐱𝟏𝟎−𝟑𝟒 (𝟑𝐱𝟏𝟎𝟖 ) = 𝟏. 𝟗𝟖𝟗𝐱𝟏𝟎−𝟏𝟓
𝛌 𝟏𝐱𝟏𝟎−𝟗

97. The division 11000 base 2 + 100 base 2 gives ____


A. 120 B. 110 C. 108 D. 90

98. In RA7920, what rule is the date and place of exam


A. 9 B. 12 C. 10 D. 11

99. How many atoms are there per unit cell for a face-centered cubic structured?
A. 1 B. 2 C. 3 D. 4

100. What is the most undesirable of all elements commonly found in steels?
A. Phosphorus B. Manganese C. Silicon D. Sulfur

145
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
ESAS PRE-BOARD EXAM MARCH 2014

1. Determine the modulus resilience for malleable cast iron E= 165 GPa, normal
stress= 230MPa.
A. 160.7 B. 170.6 C. 280.5 D. 250.8
Solution:
𝑠𝑡𝑟𝑒𝑠𝑠2
R = 𝑒𝑙𝑎𝑠𝑡𝑖𝑐𝑖𝑡𝑦

230𝑀𝑝𝑎2
R=
2(165 𝐺𝑝𝑎)

∴ 𝑹 = 𝟏𝟔𝟎. 𝟕
2. How much oxygen is required to convert 11.24g of cadmium to 12.84g cadmium
oxide.
A. 1.06g B. 1.60g C. 42.06g D. 24.08g
Solution:

𝑀𝑜𝑥𝑦𝑔𝑒𝑛 = 𝑀𝑐𝑎𝑑𝑚𝑖𝑢𝑚 𝑜𝑥𝑖𝑑𝑒 − 𝑀𝑐𝑎𝑑𝑚𝑖𝑢𝑚


𝑀𝑜𝑥𝑦𝑔𝑒𝑛 = 12.84𝑔 − 11.24𝑔
∴ 𝑴𝒐𝒙𝒚𝒈𝒆𝒏 = 𝟏. 𝟔𝟎𝒈

3. The reaction of 6.54g of zinc and 3.2g of oxygen produces 9.74g of zinc oxide, the
only compound of these elements. How much zinc oxide would be produced if 6.54g
of zinc and 5g of oxygen were mixed and allowed to react?
A. 11.54g B. 9.74g C. 1.54g D. 3.34g
Solution:

𝑀 = 𝑀𝑧𝑖𝑛𝑐 + 𝑀𝑜𝑥𝑦𝑔𝑒𝑛
𝑀 = 6.54𝑔 + 3.2𝑔
∴ 𝑴 = 𝟗. 𝟕𝟒𝒈

4. Calculate the number of moles of solute contained in 3.00L of 4.00 M solution?


A. 0.75 B. 1.33 C. 10.0 D. 12.0
Solution:

𝑁 = 𝑉 𝑥 𝑀𝑊
𝑁 = 3𝐿 𝑥 4𝑚
∴ 𝑵 = 𝟏𝟐
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
5. The minimum size of copper equipment grounding conductor required for equipment
connected to a 40 ampere branch circuit is?
A. 14 sq.mm B. 5.5 sq. mm C. 8.0 sq.mm D. 22 sq. mm

6. A single grounding electrode is permitted when resistance to ground as stated in the


PEC is:
A. 30 ohms or less C. 25 ohms or less
B. 30 ohms or more D. 25 ohms or more

7. Find the pressure experienced by a scuba diver at a depth of 40m in a salt


seawater?
A. 404kPa B. 44.0kPa C. 4.04kPa D. 440kPa
Solution:

𝐹 = 𝑝𝑔ℎ
𝐹 = (1.03)(9810)(40)
∴ 𝑭 = 𝟒𝟎𝟒. 𝟏𝟕𝟐𝑲𝒑𝒂

8. Given 30 mmHg abs. Find the gauge pressure in kPa


A. -98kPa B. 98kPa C. -89kPa D. 89kPa
Solution:

𝑃𝑔𝑎𝑢𝑔𝑒 = 𝑃𝑎𝑏𝑠 − 𝑃𝑎𝑡𝑚


101.325 𝐾𝑝𝑎
𝑃𝑔𝑎𝑢𝑔𝑒 = (30𝑚𝑚 𝐻𝑔 𝑥 ) – 101.325 𝐾𝑝𝑎
760 𝑚𝑚 𝐻𝑔
∴ 𝑷𝒈𝒂𝒖𝒈𝒆 = −𝟗𝟖 𝑲𝒑𝒂

9. A marble rolling with the speed of 20 cm/s, rolls at the edge of a table that is 60cm
high, how far horizontally, from the table edge does the ball strike the floor.
A. 5.9cm B. 6.4cm C. 8.1cm D. 7.2cm
Solution:

𝐸𝑞𝑢𝑎𝑡𝑖𝑜𝑛 𝑜𝑓 𝑇𝑟𝑎𝑗𝑒𝑐𝑡𝑜𝑟𝑦
−𝑔𝑋 2
−𝑦 =
2𝑣𝑜2
−981𝑋 2
−80 =
2𝑣𝑜2
∴ 𝑿 = 𝟖. 𝟏𝒄𝒎
10. An interest rate is quoted as being 1.5% per month and compound monthly. What is
the effective annal interest rate?
147
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 18.12% B. 19.56% C. 1.51% D. 16.95%
Solution:

𝐸𝑅𝐼𝑚𝑜𝑛𝑡ℎ𝑙𝑦 = 𝐸𝑅𝐼𝑎𝑛𝑛𝑢𝑎𝑙𝑙𝑦
(1 + 0.015)12 – 1 = (1 + 𝑖)1 – 1
∴ 𝒊 = 𝟏𝟗. 𝟓𝟔 %
11. This principle states that “Where the velocity of the fluid is high, the pressure is low,
and where the velocity is low, the pressure is high”.
A. Archimedes Principle C. Flow Principle
B.Toriceilli’s Principle D. Bernouili’s Principle

12. What is the chemical formula for Sulfur Trioxide


A. S3O2 B. S2O C. S2O3 D. SO3

13. In how many years will the investment to double in value at 5% interest rate?
A.. 2 B. 4 C. 20 D.40
Solution:

. 𝐹 = 𝑃 ( 1 + 𝑖𝑛 )
2 = 1 ( 1 + 0.05𝑛 )
∴ 𝒏 = 𝟐𝟎 𝒚𝒓𝒔.
14. An archer his bow upward and pulls the string of his arrow with a force of 80N. the
string makes and angle of 25 degrees with the vertical. Find the tension of the string.
A.88N B. 44N C. 22N D.33N
Solution:
𝐹
2
𝑇= cos 𝜃
80
2
𝑇= cos 25
𝑻 = 𝟒𝟒 𝑵

15. It requires Q of heat to make of coffee. How much energy is needed to make 3 cups
of coffee?
A. 3 Q B. 2 Q C. Q D. 4 Q

Solution:

148
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑄𝑇 = 𝑄1 + 𝑄2 + 𝑄3
∴ 𝑸𝑻 = 𝟑𝑸

16. Car travelled 20m/s south in 3min, 25 m/s east in 2min 30m/s northeast in 1min.
Find the average speed in 6min?
A.15.31m/s B. 13.51 m/s C. 32.33 m/s D. 23.33 m/s
Solution:

𝑆𝑎𝑣𝑒. = 𝑑⁄𝑡

(30)(3)(60) + (25)(2)(60) + (30)(10)(60)


(6)(60)
∴ 𝑺𝒂𝒗𝒆. = 𝟐𝟑. 𝟑𝟑 𝒎/𝒔.
17. Car travelled 20m/s south in 3min, 25 m/s east in 2min 30m/s northeast in 1min.
Find the average velocity in 6min?
A.15.31m/s B. 13.51 m/s C. 32.33 m/s D. 23.33 m/s
Solution:

𝑉𝑎𝑣𝑒. = 𝑑⁄𝑡

(20∟-90)(3)(60)+(25)(2)(6)+(30∟45)(1)(60)
(6)(60)
∴ 𝑽𝒂𝒗𝒆. = 𝟏𝟑. 𝟓𝟏 𝒎/𝒔
18. Find the maximum and minimum sum of the vectors A and B with magnitude 12 and
8, respectively.
A.20 and 10 B. 20 and 4 C. 12 and 8 D. 12 and 4
Solution:

𝑀𝑎𝑥. = 12 + 8 = 𝟐𝟎
𝑀𝑖𝑛. = 12 – 8 = 𝟒
19. Calculate the pH value of 8.0 M HCI
A. 0.903 B. -0.903 C. 0.309 D. -0.309
Solution:

𝑃𝐻 = − log(𝐻)
𝑃𝐻 = − log(8)
𝑷𝑯 = −. 𝟗𝟎𝟑
149
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS

20. Calculate the molarity of a 250-ml solution containing 80.0 mmol of solute.
A. 0.320M B. 0.230M C. 0.820M D. 0.280M
Solution:

𝑀 = 80/250
∴ 𝟎. 𝟑𝟐 𝑴𝒐𝒍𝒆
21. The charge of aluminum atom in the aluminum foil is:
A. 0 B. +1 C. +2 D. +3

22. What is CPE in RA 7920 stands for?


A. Continuous Professional Educatio C. Continuous Professional Educator
B. Continuing Professional EducationD.ContinuingProfessional Educator

23. What is PSALM in EPIRA stands for.


A.PrivateSectorAssetsandLiabilitiesManagement
B. Private Section Assets and Liabilities Management
C. Power Sector Assets and Liabilities Management
D. Power Section Assets and Liabilities Management

24. A deposit of P10,000 is made in the bank account that pays 8% interest
compounded annually. How much money will be in the account after one year?
A.P10,600 B. P10,700 C. P10,800 D. P10.600

Solution:
𝐹 = 𝑃 ( 1 + 𝑖 )𝑛 = 10,000(1 + 0.08)1
∴ 𝑭 = 𝟏𝟎, 𝟖𝟎𝟎

25. It is the sum of the internal energy and PV


A. entropy B. enthalpy C. energy D.electric field
26. A boy and his sledge weighs m, on an inclined surface with angle of inclination of
phi. And coefficient friction of u. What is the frictional force?
A. mgsinphi B. mgcosphi C. 𝜇mgsinphi D. 𝝁mgcosphi

27. Two sky divers jump at the same time and want to play catch. Where should one
aim if he wants the other catch it?
A. below C. above because ball falls slower
B. above because ball falls faster D. straight because there’s no air resistance

150
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
28. Which of the following is not part of this requirements to take RME?
A. Taken 1-year electrician course and 3-years appreniceship
B. Taken 2-year electrician course and 2-years appreniceship
C. Taken 3-year electrician course and 1-years appreniceship
D. Graduate of BSEE

29. Which of the following is non-renewable energy?


A. nuclear B. wind C. solar D. geothermal

30. What is JCPC is EPIRA stands for?


A. Joint Congressional Power Committee
B. Joint Congress Power Committee
C. Joint Congressional Power Commission
D. Joint Congress Power Commission

31. What is PEMC is EPIRA stands for?


A. Philippine Electricity Market Commission
B. Philippine Electricity Market Company
C. Philippine Electricity Market Committee
D. Philippine Electricity Market Corporation

32. A reinforced concrete column 250mm in diameter is designed to carry an axial


compressive load of 400kN. Using allowable stresses for concrete of 6MPa and
stands for steel of 120MPa, find the required area of stresses of reinforcing steel.
Assume Ec= 14Gpa and Es= 200Gpa. .
A.1728 sq.mm B. 1323 sq.mm C. 1636 sq.mm D.1448 M2

Solution:

Ɣ𝑐 = Ɣ𝑠 Ɣ𝑐 = Ɣ𝑠
𝑆𝐿 𝑆𝐿
=
𝐸 𝐸
6𝑀 𝑆𝑠
=
14 𝐺𝑃𝑎 200 𝐺𝑃𝑎
𝑆𝑠 = 85. 71 𝑀𝑃𝑎

𝑆 = 𝑃⁄𝐴
𝜋
𝐴𝑐 + 𝐴𝑠 =
4(250 𝑥10−3 )2

151
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝜋
𝐴𝑐 = − 𝐴𝑠
4(250 𝑥10−3 )2
𝑆𝑐𝐴𝑐 + 𝑆𝑠𝐴𝑠 = 400,000
(6𝑀)(𝜋/4 × 250 × 10 − 3 ) – 𝐴𝑠) = (85.71𝑀)𝐴𝑠 = 𝟒𝟎𝟎, 𝟎𝟎𝟎
A = 1.323×10-3m2×10002mm2
1m2
∴ 𝑨 = 𝟏𝟑𝟐𝟑. 𝟐𝟒𝒎𝒎𝟐
33. An aluminum tube (G = 28 GPa) has an outer diameter of 100mm and an inner
diameter of 60mm. when twisted by a torque T, the tube develops a maximum
normal straim of 650 x 10-6. What is the magnitude of the applied torque T?
A. 8500 N-m. B. 5600 N-m C. 6700 N-m D. 7600 N-m

Solution:
𝟏𝟔𝑻𝑫
𝝉= 𝝅(𝑫𝟒 −𝒅𝟒 )
𝜏 = 𝐸𝜀
𝜏 = 70𝑥109 (65𝑥10−6 )
𝜏 = 45.5 𝑥106
100
16𝑇 (1000)
45.5 𝑥106 =
100 4 60 4
𝜋 ((1000) − (1000) )
∴ 𝑻 = 𝟕𝟕𝟕𝟔. 𝟎𝟕 𝑵 − 𝒎 ≈ 𝟕𝟔𝟎𝟎𝑵 − 𝒎

34. What is TSC in EPIRA stands for?


A. Transition Supplier Contract
B TransitionSupplyContract
C. TransitionSupplierCommission
D. Transition Supply Commission

35. The rate of change of shear strain in fluid is:


A. Shear rate B. pressure rate C. stress rate D. strain rate

36. If a twisting moment of 10,000 lb-in is impressed upon a 1-3/4 in diameter shaft,
what is the angle of twist In a 4ft length of the shaft? The material is steel which is
G= 12 x 106 psi.
A. 0.0543 rad B. 0.0435 rad C. 0.0235 rad D. 0.0325 rad

Solution:

152
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝛾 = (10,000)(12)
𝜋/4(1 − 3/4)4(12 × 104)
∴ 𝟎. 𝟎𝟒𝟑𝒓𝒂𝒅
37. A square steel bar is 2 inches on a side and 10 inches long. It is loaded by an axial
tensile force of 40000 lb. if E = 30x10 6 psi and 𝜇 = 0.3, determine the change of
volume per unit volume.
A. 0.000133 B. 0.00133 C. 0.000122 D. 0.00122

Solution:

𝚫𝑽 𝑷
= 𝑨𝑬 (𝟏 − 𝟐𝝁)
𝐕
Δ𝑉 40,000
= 2 (1 − 2(0.3))
V 2 (30𝑥106 )
𝚫𝑽
∴ = 𝟎. 𝟎𝟎𝟎𝟏𝟑𝟑
𝐕
38. A car moving at 30 m/s slows uniformly to speed of 10 m/s in a time of 5.0s.
Determine the distance of moves in the third second.
A. 10m B. 15m C. 20m D. 30m

Solution:

𝑉𝑓 = 𝑉𝑜 + 𝑎𝑡
1 = 0 + 𝑎(5)
𝑎 = −4𝑚/𝑠
1
𝑆3 = 𝑉𝑜𝑡 +
2𝑎𝑡 2
𝑆3 = 7(3) + ½(−4)(3)2
𝑆3 = 72
𝑆2 = (30)(2) + ½(−4)(2)2
𝑆2 = 52
𝑺𝟐𝟑 = 72 – 52 = 𝟐𝟎𝒎
39. In RA 7920, under the Penalty Clause, The fine shall be:
A. not less than P60,000 C.notlessthanP20,000
B. not less than P50,000 D. not less than P10,000

153
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
40. A solid cube of aluminum is 2.00cm on each edge. The density of aluminum is 2700
kg/cu.m. Find the mass of the cube?
A. 26.1g B. 21.6g C. 32.4g D. 34.2g
Solution:

𝑀𝑎𝑠𝑠 = 𝑣𝑜𝑙𝑢𝑚𝑒 𝑥 𝑑𝑒𝑛𝑠𝑖𝑡𝑦


= (8𝑥106) (2700 𝑘𝑔/𝑚3)
∴ 𝟐𝟏. 𝟔 𝒈
41. Calculate the force due to the pressure acting of the 1-m diameter horizontal hatch
of a submarine submerged 600m below the surface.
A. 4.62 x 10^8N B. 4.62 x 10^5 N C. 4.26 x 10^8 N D.4.26x 10^5
Solution:

𝐹 = 𝛾ℎ𝐴
𝜋
𝐹 = (9.81 𝑥103 )(600) ( 4 ) (1)2

𝑭 = 𝟒. 𝟐𝟔 𝒙𝟏𝟎𝟖 𝑵
42. The temperature of a body is 50 deg F. find the temperature in K.
A. 10 B. 263 C. 283 D. 510
Solution:
𝟓
(℉ − 𝟑𝟐) ∗ + 𝟐𝟕𝟑 = 𝑲
𝟗

5
(50 ℉ − 32) ∗ + 273
9
∴ 𝑲 = 𝟐𝟖𝟑
43. Determine the force necessary to accelerate a mass of 20 lbm, at a rate of 60
ft/sq.sec vertically upward.
A.37.3 lbf B. 57.3 lbf C. 73.3 lbf D. 75.3 lbf
Solution:
60
𝐹 = (20)(1 + 32.2)

∴ 𝑭 = 𝟓𝟑. 𝟑𝒍𝒃𝒇
44. In thermodynamics our attention is focused on which form of energy.
A. Kenetic energy B. internal enegy C. Potential energy D.Total energy

154
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
45. Energy is added to a piston-cylinder arrangement, and the piston is withdrawn in
such a wa that are quantity PV remains constant. The insist pressure and volume
are 200kPa and 2 cu.m, respectively. If the final pressure is 100kPa, Calculate the
work done by the gas on the piston.
A. 428kJ B. 482kJ C. 287kJ D. 277Kj

Solution:
𝑃
𝑊 = 𝑃1 𝑉1 𝑙𝑛 (𝑃1 )
2

200
𝑊 = (200)(2) ln (100)

𝑾 = 𝟐𝟕𝟕 𝒌𝑱

46. The shaft drives in an automobile delivers 100 N-m of torque as it rotates 3000 rpm.
Calculate the horsepower delivered ?
A. 46.2Hp B. 84.6Hp C. 42.1Hp D. 86.4Hp
Solution:
2𝜋𝑁𝑇 (2𝜋)(3000)(100)
𝐻𝑃 = =
60 60
∴ 𝑯𝑷 = 𝟒𝟐. 𝟏𝟏 𝒉𝒑
47. A 0.75Hp motor acts for 8.0s on an initially non-rotating wheel having a moment of
inertia of 2kg-sq.m, Find the angular speed developed in the wheel, assuming no
losses.
A. 67 rad/s B. 76 rad/s C. 89 rad/s D. 98 rad/s
Solution:

𝑊𝑜𝑟𝑘 𝑑𝑜𝑛𝑒 𝑏𝑦 𝑚𝑜𝑡𝑜𝑟 𝑖𝑛 8.0 𝑠 = 𝐾𝐸 𝑜𝑓 𝑤ℎ𝑒𝑒𝑙 𝑎𝑓𝑡𝑒𝑟 8.0 𝑠


1
(𝑝𝑜𝑤𝑒𝑟) 𝑥 (𝑡𝑖𝑚𝑒) = 2 (𝐼)(𝜔)²

(0.75 ℎ𝑝)(746 𝑊/ℎ𝑝)(0.8 𝑠) = 1/2(2.0 𝑘𝑔. 𝑚^2)(𝜔)²


∴ 𝝎 = 𝟔𝟕 𝒓𝒂𝒅/𝒔
48. The length of free conductors at outlets and switch point for splices and connection
of fixture and develops must be at least
A. 80mm B. 100mm C. 120mm D. 150mm

155
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
49. It is the process of determining the value or worth of a physical property for specific
reason.
A. investment B. valuation C. economy D. depletion

50. How high would water rise in the pipes of a building if the water pressure gauge
show the pressure at the ground floor to be at 270kPa?
A. 28.9m B. 29.8m C. 27.5m D. 25.7m
Solution:
270𝑘𝑃𝑎
𝑍 =
9.81𝑚/𝑠
∴ 𝒁 = 𝟐𝟕. 𝟓 𝒎
51. An annuity where the payments are made at the beginning of each period.
A. ordinary annuity B. deferred annuity C. annuity due D. perpetuity

52. The air in the cylinder of the air compressor is compressed from 100kPa to 10MPa.
Estimate the final temperature required if the air is initially at 100 degree celsius.
A. 37300K B. 33700K C. 1930K D. 1390K
Solution:
𝑷𝟏 𝑷𝟐
= 𝑻𝟐
𝑻𝟏

𝟏𝟎𝟎𝒙𝟏𝟎𝟑 𝟏𝟎𝟎+𝟐𝟕𝟑
=
𝟏𝟎𝒙𝟏𝟎𝟔 𝑻𝟐

𝑻𝟐 = 𝟑𝟕𝟑𝟎𝟎𝑲
53. What is the minimum diameter of a solid steel shaft that will not twist through more
than 3 deg in 6-m length, when subjected to a torque of 14Kn-m?
A. 0.500m B. 0.125m C. 0.118m D. 0.220m
Solution:

Ɵ = 𝑇𝐿⁄ 𝜋𝐷4
( 32 )(𝐺)

(14000)(6)
3 = ⁄ 𝜋𝐷4
( 32 )(83𝑥109 )

∴ 𝑫 = 𝟎. 𝟏𝟏𝟖 𝒎

156
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
54. Sec 17(b) of Art lll: Examination and Registration, Qualifications of applicants for
Registered Electrical Engineer, states that an applicant is at least be ___ years of
age.
A. 21 B. 23 C. 24 D. 25

55. The number 1000 base 2 is equivalent to decimal number ____.


A. 1000 B. 16 C.8 D. 4

56. A tank of volume 590 liters contains oxygen at 20 deg C and 5.0 atm pressure.
Calculate the mass of horizontal component of its velocity will be
A. 3.9kg B.9.3kg C.2.8kg D.6,2kg
Solution:

(5)(101.325𝐾𝑃𝑎)(590/1000) = 𝑚(251.9)(20 + 273)


𝑚 = 3.79 = 𝟑. 𝟗𝒌𝒈

57. A ball is thrown at a 30 degrees angle above the horizontal with a speed of 10ft/s.
After 0.50s the horizontal component of its velocity will be
A. 9ft/s B.10ft/s C.12ft/s D.19ft/s
Solution:
2𝑉𝑠𝑖𝑛α
𝑡=
𝑔
2𝑉𝑠𝑖𝑛30
0.5 =
20
∴ 𝑽 = 𝟏𝟎 𝒇𝒕/𝒔𝒆𝒄
58. The machine that is employed for converting the energy of flow in a pipeline into
mechanical work is called
A. turbine B. pump C. nozzle D. motor

59. What is decimal value equivalent of the binary number 101.1101?


A. 5.8031 B. 5.8531 C. 5.8021 D. 5.8125
Solution:

𝑁 = 1𝑥10−1 + 1𝑥10−2 + 0𝑥10−3 + 1𝑥10−4


𝑁 = 0.8125
𝑁 = 5 + 0.8125
∴ 𝑵 = 𝟓. 𝟖𝟏𝟐𝟓

157
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
60. The coefficient of static friction for steel on ice is 0.1. the force needed to set a 70-kg
skater in motion is about.
A. 0.1N B. 0.7N C. 7N D. 70N
Solution:

𝐹 = 70(9.81)(0.1)

𝐹 = 68.67𝑁
∴ 𝑭 = 𝟕𝟎𝑵
61. A 3.2-lb stone at the end of a string 2.0 ft long is whirled in a vertical circle. The
tension in the string is 5.0-lb when the stone is set at the top of the circle. The
stone’s velocity when is
A. 1.8ft/s B. 6.0ft/s C. 10ft/s D. 12.6ft/s
Solution:
𝑚𝑉 2
𝑇= 𝑟

3.2 𝑉2 𝒇𝒕⁄
5 = [32.2] [ 2 ] = 𝟏𝟎 𝒔
62. The equivalent grounding conductor of a branch circuit shall be identified by what
color?
A. red with green stripe B. white C. black and yellow D.greenand yellow

63. A car that travels at 40kph for 2.0hrs, at 50kph for 1.0hr, and at 2 kph for 0.50 hr,
has an average speed of
A. 31pkh B. 40kph C. 45kph D. 55kph
Solution:
𝐷1(𝑇1) + 𝐷2(𝑇2) + 𝐷3(𝑇3)
𝐴𝑆 =
𝑇1 + 𝑇2 + 𝑇3

(40𝑥2) + (50𝑥1) + (2𝑥. 5)


𝐴𝑆 =
2 + 1 + .5
𝑨𝑺 = 𝟒𝟎 𝒌𝒑𝒉
64. A copper bar is 1,0m long at 20 deg C. at what temperature will it be shorter by 1.0
min?
A. -17 deg C B. -39 deg C C. -59 deg C D. -79 deg C
Solution:

(−1𝑥10 − 3) = (16.5𝑥10 − 6)(1)(𝑇 − 20)


158
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑇 = −40.6 𝑑𝑒𝑔 𝐶
∴ 𝑻 = −𝟑𝟗 𝒅𝒆𝒈 𝑪

65. A ball thrown horizontally from the roof of a building 45.0m tall and lands 24.0m from
the base. What was the ball’s initial speed.
A. 60g B. 75g C. 120g D. 200g
Solution:

𝑄 = 𝑚𝑐 𝑇
𝑄𝑟 = 𝑄𝑙
𝑚(40 − 100) = (300)(0 − 40)
∴ 𝒎 = 𝟐𝟎𝟎𝒈

66. The most important element that controls the physical properties of steel is.
A. silicon B. tungsten C. manganese D. carbon

67. A heat pump delivers 20,000 kJ/hr of heat with a 1.39 kW input. Calculate the COP.
A. 2 B. 3 C. 4 D. 5
Solution:
Q
COP =
P
20000
COP =
1.39x3600
∴ 𝑪𝑶𝑷 = 𝟒

68. Spark plug makes use of which of the following materials for insulation?
A. porcelain B. asbestos C. slate D. glass

69. A ball is thrown horizontally from the roof of a building 45.0m tall and lands 24.0m
from the base, What is was the ball’s initial speed?
A. 6.32m/s B. 4.43m/s C. 8.68m/s D. 7.92m/s
Solution:

x = x0+ Vot y = yo+ Vot+ ½ ayt2


x = 0 + Vot 0 = yo + 0 + ½ ayt2
x=Vot 0 = yo + ½ ayt2

x −2yo
Vo = t=√
t 𝑎𝑦
159
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
24 −2(45)
Vo = t=√
3.0304 −9.81

∴ 𝑽𝒐 = 𝟕. 𝟗𝟐 𝒎/𝒔 t = 3.0304s

70. In electrochemistry, oxidation is a loss of _________.


A. electron B. proton C. ion D. anode

71. What is the maximum operating temperature of a THWN conductor?


A. 60 deg C B. 75 deg C C. 90 deg C D. 110 deg C

72. Cash money and credit necessary to establish and operate on enterprises.
A. capital B. funds C. assets D. liabilities

73. What is the form of the moment diagram of a beam supported at both ends and
carrying a uniform distributed load.
A. triangle B. hyperbola C. parabola D. rectangle

74. Every object continues in its state of rest, or of uniform velocity in a straight line, as
long as no net force acts on it, this statement is in the accordance ti
A. newton first law of motion C. newton’s third law of motion
B. newton’s second law of motion D. all of these

75. When a pressure of 2.0 MPa is applied to a sample of kerosene, it contracts by


0.15%. the bulk modulus of kerosene is:
A. 1.8GPa B. 1.1GPa C. 1.6GPa D. 1.3GPa
Solution:
𝑃
𝛽= ∆𝑉
𝑉

2𝑥106
𝛽= = 𝟏. 𝟖 𝑮𝑷𝒂
0.15%
76. P 12.000 is borrowed now at 12% interest. The first payment P4,000 and is made 3
years from now, The balance of debt is immediately after the payment is:
A. P4,000 B. P8,000 C. P12,000 D. P12,860
Solution:

𝐹 = (12,000)(1 + 0.12)3
𝐹 = 16859.136
𝐵𝑎𝑙𝑎𝑛𝑐𝑒 = 𝐹 − 𝑃1
160
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐵𝑎𝑙𝑎𝑛𝑐𝑒 = 16859.136 − 4000
∴ 𝑩𝒂𝒍𝒂𝒏𝒄𝒆 = 𝑷𝟏𝟐𝟖𝟓𝟗. 𝟏𝟑𝟔 ≈ 𝟏𝟐, 𝟖𝟔𝟎. 𝟎𝟎

77. The first period contains how many elements.


A. 2 B. 4 C. 6 D. 8

78. Any equipment which produces, modifies, regulates, or controls the supply of
electric energy is the “______________”
A. Electric Supply Equipment C. Substation
B. Transformer D. Generator Set

79. If ṩ10,000 is borrowed now at interest of 6%, how much will remain to be paid after a
ṩ3,000 payment is made four years from now?
A. ṩ9,400 B. ṩ7,000 C. ṩ9.625 D.ṩ9,725
Solution:

𝐹 = (10000)(1 + 0.06)4
𝐹 = 12624.77
𝐵𝑎𝑙𝑎𝑛𝑐𝑒 = 12624.77 − 3000
∴ 𝑩𝒂𝒍𝒂𝒏𝒄𝒆 = 𝟗. 𝟔𝟐𝟓

80. Compute the average speed of water in a pipe having an inside diameter of 5.0cm
and delivering 2.5cu.m of water per hour.
A. 0.28m/s B. 0.96m/s C. 0.35m/s D. 0.85m/s
Solution:

𝐵𝑦 𝑢𝑛𝑖𝑡 𝑎𝑛𝑎𝑙𝑦𝑠𝑖𝑠
25
[ ]
(60)(60)
𝐴𝑉 =
𝜋 5 2
[(4) (100) ]

∴ 𝑨𝑽 = 𝟎. 𝟑𝟓 𝒎⁄𝒔

81. The theoretical head in m, required to push water through a 3-cm round orifice at
15m/s is closest to
A. 11.5 B. 12.7 C. 13.4 D. 1.5

82. A machine an initial cost of P50,000.00 and a salvage value of P10,000.00 after 10
years. What is the book value after 5 years using straight line depreciation?
161
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. P35,000.00 B. P25,000.00 C. P15,000.00 D. P30,000.00
Solution:
(𝐶𝑜−𝐶𝑙)
𝐶𝑛 = 𝐶𝑜 − 𝑛[ ]
𝐿

𝐶𝑛 = 50,000
(50,000 − 10,000)
−5 [ ]
10
∴ 𝑪𝒏 = 𝑷𝟑𝟎, 𝟎𝟎𝟎. 𝟎𝟎

83. A 20-kg piston rests on a sample of a gas in a cylinder 10cm radius. The absolute
pressure of the gas is?
A. 0.0064bar B. 0.062bar C. 1.019bar D. 1.075bar
Solution:

84. An annuity of ṩ5600 is paid each year for 10 years. The payment is made at year
end. If the interest rate is 10%, what is the present worth of the 10 payments?
A. ṩ14526 B. ṩ89247 C. ṩ56000 D. ṩ34110
Solution:
{(1+0.10)10 −1}
𝑃 = 5600[ ]
(0.10)(1+0.10)10
∴ 𝑷 = 𝟑𝟒𝟏𝟏𝟎

85. Calculate the volume at STP of 26.7g of oxygen gas.


A. 17.8L B. 87.1L C. 18.7L D. 78.1L
Solution:
1𝑘𝑔 259.90𝐽
(101.325𝑥103 )𝑉 = (26.7𝑔) (1000𝑔) ( ) (273)
𝑘𝑔۰𝐾
1000𝐿
𝑉 = 0.018697𝑚3 ( )
1𝑚3
∴ 𝑽 = 𝟏𝟖. 𝟕𝑳

86. A baseball bat strikes a ball with a force of 30-N. if the ball was in contact with the
bat fir 1/10 of a second. What impulse did the ball receive?
A. 3 N-s B. 6 N-s C. 9 N-s D. 12 N-s
Solution:
1
. 𝐹 = 𝑓𝑡 = (30) (10)

162
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
∴ 𝑭 = 𝟑𝑵

87. The minimum size of conductors to be used for lighting purposes is:
A. 1.5 sq.mm B. 1.25 sq.mm C. 1.75 sq.mm D. 2.0 sq.mm
88. A forces of 10-N is applied to one end of a 10 in diameter circular rod. Calculale the
stress.
A. 0.15kPa B. 0.10kPa C. 0.20kPa D. 0.05kPa
Solution:
10
𝑆= 𝜋 2.54𝑐𝑚 1𝑚 2
[( )(10𝑖𝑛 𝑥 𝑥( ) )]
4 1 𝑖𝑛 100𝑐𝑚

∴ 𝑺 = 𝟎. 𝟐𝟎𝑲𝑷𝒂

89. Calculate the molality of a solution containing 0.500 mol of solute in 250g of solvent.
A. 1.50m B. 2.00m C. 2.50m D. 3.00m
Solution:

𝑀 = 0.5/(250/1000) = 𝟐 𝒎

90. The president of a growing engineering firm wishes to give each of 50 employees a
holiday bonus, how much is needed to invest monthly for a year at 12% nominal rate
compounded monthly, so that each employee will receive P1000 bonus?
A. P3942.44 B. P3271.22 C. P3600.12 D. P3080.32
Solution:
𝑛𝑡 12
𝑟 0.12
𝐴[(1+( )) −1] 𝐴[(1+( )) −1]
𝑛 12
𝑟 ; (50)(1 × 103 ) = 0.12
𝑛 12
∴ 𝑨 = 𝑷𝟑𝟗𝟒𝟐. 𝟒𝟒

91. A hallow shaft has an inner diameter of 0.035m and an outer diameter of 0.06m.
compute the torque if the shear stress is not to exceed 120MPa.
A. 4500 N-m B. 4100 N-m C. 4300 N-m D. 4150 N-m

Solution:
𝟏𝟔𝑻𝑫
Ԏs== 𝝅(𝑫𝟒 −𝒅𝟒 )
16𝑇(0.06)
120𝑀𝑃𝑎 = 𝜋(0.064 −0.0354 )
∴ 𝑻 = 𝟒𝟓𝟎𝟎 𝑵 − 𝒎
163
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
92. What mass in grams of solute is needed to prepare 3.50L of 0.400M NaOH?
A. 54 B. 56 C. 52 D. 58
Solution:

Na = 23g/mol
O = 16g/mol
H = 1g/mol
𝒎𝒐𝒍𝒆𝒔 𝒐𝒇 𝒔𝒐𝒍𝒖𝒕𝒆
M = 𝑳𝒊𝒕𝒆𝒓 𝒐𝒇 𝒔𝒐𝒍𝒖𝒕𝒊𝒐𝒏
0.400 𝑚𝑜𝑙𝑒 𝑥
= [ ] / 3.5𝐿
𝐿 (23 + 16 + 1)𝑔/𝑚𝑜𝑙
𝒙 = 𝟓𝟔 𝒈𝒓𝒂𝒎𝒔
93. What load in lb, must be applied to a 1-in round steel bar 8ft long (E=30x10^6 psi) to
stretch a the bar 0.05in?
A. 7200 B. 9800 C. 8600 D. 12250

Solution:
𝑷𝑳
δ = 𝑨𝑬
𝑃(8×12)
0.05 = 𝜋 6
( )(1)2(30×10 )
4
∴ 𝑷 = 𝟏𝟐𝟐𝟓𝟎𝒍𝒃
94. A gas expands by 1.0L at a constant pressure of 2.0 bars, During the expansion
500J of heat is added . find the change in the internal energy?
A. 300J B. 200J C. 400J D. 100J
Solution:

1L*bar = 100 Joules


Q = ΔU + W
ΔU = Q – W
100 Joules
ΔU = 500J – (1L*2 bar) ( )
1L∗bar
∴ 𝜟𝑼 = 𝟑𝟎𝟎𝑱
95. A man expects to receive P20,000 in 10 years. if interest is computed at 6% interest
compounded quarterly, how much is it worth today?
A. P11,025.25 B. P11,035.25 C. P11,045.25D. P11,055.25
Solution:
𝒏𝒕
𝒓
𝑭 = 𝑷 (𝟏 + (𝒏))

164
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
0.06
20,000 = 𝑃(1 + ( )^10𝑥4
4
∴ 𝑷 = 𝑷𝟏𝟏, 𝟎𝟐𝟓. 𝟐𝟓

96. A sharp edge orifice will be required to produce a discharge of 35liters/sec of water
under a head of 3m. the required diameter is nearest to, when C-0.596.
A. 125mm B. 100mm C. 75mm D. 50mm

97. LED displays represents


A. Loop Emitter Decoder C. Long Emission Disc
B. Light Emitting Diode D. Logic Electrostatic Diode

98. What velocity in m/s did an airplane take off from a landing field that has run 500m if
it starts from rest, moves the constant acceleration and makes the run in 30sec?.
A. 33.33 B. 45.15 C. 56.67 D. 66.67
Solution:
(𝑽𝒇+𝑽𝒐)(𝒕)
.𝑺 = 𝟐
(𝑉𝑓+0)(30)
500 = 2
∴ 𝑽𝒇 = 𝟑𝟑. 𝟑𝟑 𝒎/𝒔

99. A 600 N object is to be given an acceleration of 0.70m/sq.sec. How large an


unbalanced force must act upon it?
A. 39 N B. 93 N C. 43 N D. 34 N
Solution:
𝒘𝒂
𝑭= 𝒈
600(0.70)
𝐹= 9.81
∴ 𝑭 = 𝟒𝟑 𝑵
100. A car has wheels of radius of 30cm. if starts from rest and accelerates uniformly
to a speed of 15m/s in a time of 8.0s. find the number or rotations one wheel makes
in this time.
A. 36 B. 32 C. 26 D. 2
Solution:
(𝑽𝒇+𝑽𝒐)(𝒕)
𝑺= 𝟐
(15+0)(8)
𝑆= 2
S = 60 m
165
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2014
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑺
𝑵=𝑪
60
N= 𝟑𝟎
𝟐𝜫( )
𝟏𝟎𝟎
∴ 𝑵 = 𝟑𝟐

166
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
ESAS PRE-BOARD EXAM AUGUST 2013

1. A barrel will rupture when the gauge pressure within it reaches 350 kPa. It is
attached to the lower end of a vertical pipe, with the pipe and the barrel with oil (ρ =
890kg/cu.m.). How long can the pipe be if the barrel is not rupture?
A. 39.2m B. 40.1m C. 41.6m D. 36.4m

Solution:
𝑷 = 𝜸𝑾(𝑺. 𝑮)
890
35 𝑘𝑃𝑎 = (9.81𝑥103 ) (1000) (ℎ)
∴ 𝒉 = 𝟒𝟎. 𝟏 𝒎

2. When a submarine dives to depth of 120m, to how large a total pressure is its
exterior surface subjected? The density of seawater is about 1.03 g/cu.cm.
A. 2.64MPa B. 1.22MPa C. 1.31Mpa D. 1.62MPa

Solution:

1 𝑏𝑎𝑟 𝑖𝑠 𝑎𝑏𝑜𝑢𝑡 100 000 𝑃𝑎𝑠𝑐𝑎𝑙 𝑜𝑟 1𝑥105


𝑃 = 𝑃𝑏 + (𝑃𝑜)(𝑔)(ℎ)
5
1.03𝑥103 𝑔 𝑚
𝑃 = 1𝑥10 𝑃𝑎 + ( 3
) (9.8 ) (120𝑚)
𝑐𝑚 𝑠
𝑷 = 𝟏. 𝟑𝟏𝑴𝒑𝒂
3. A vertical test tube has 2 cm of oil (ρ= 0.8 g/cu. cm.) floating on 8.0 cm of water.
What is the pressure at the bottom of the tube due to the fluid in it.
A. 0.94kPa B. 0.69kPa C 0.68kPa. D. 0.78kPa

Solution:

𝑃1 = 𝑝𝑔ℎ
= (800 𝑘𝑔/𝑚)(9.81 𝑚/ 𝑠2)(2𝑥10 − 2)
𝑃1 = 156.96
𝑃2 = (9810 𝑚/𝑠2)(8𝑥10 − 2)
𝑃2 = 784.8
𝑃𝑇 = 𝑃1 + 𝑃2
= 156.96 + 784.8
𝑃𝑇 = 941.76 𝑃𝑎 𝑜𝑟 𝟎. 𝟗𝟒𝟏𝟕𝟔 𝒌𝑷𝒂

4. A side (2 in) of a square bar is loaded in tension by a force of 12 kips. Determine the
normal stress in ksl in the square bar.
A. 5.5 B.6 C. 2.6 D. 3

Solution:
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A = (2)(2) = 4 in2
𝑃
S=𝐴
12
= 4
∴𝑺=𝟑
5. What is the chemical formula of ammonia?
A. NH4 B. NH3 C. N2H3 D. N3H2

6. What is the empirical formula for C2H6.


A.CH3 B. C2H C. CH2 .D. C3H2

7. Maximum Distance for support of rigid metallic conduits.


A. 2000mm B. 2500mm C. 3000mm D3500mm

8. The minimum diameter of a steel ground electrode is.


A. 10mm B. 12mm C. 14mm D. 16mm

9. What is the maximum height an arrow can achieved when shot with initial velocity of
100m,/s.
A. 418.96m B. 481.95m C. 590.68m D. 509.6m

Solution:
1
𝑉𝑓 – 𝑉𝑜 = −𝑔𝑡 ℎ = 𝑉𝑜𝑡 − − 2 𝑔𝑡 2
1
0 − 100 = −9.81(𝑡) ℎ = 100(10.19) − (9.81)(10.19)2
2

𝑡 = 10.19 ∴ 𝒉 = 𝟓𝟎𝟗. 𝟔 𝒎
10. A ball struck by a bat fly in a perfect vertical direction after being hit by a battler.
A fan observes that it reaches its peak at a time t= 3s. Find its maximum height.
A. 43.195m B. 44.145m C. 52.286m D. 58.264m

Solution:
𝑆 = 𝑉𝑂 𝑡 − 1⁄2 𝑔𝑡 2
𝑉𝑓 2 = 𝑉𝑂 2 ± 2𝑔𝑠
@ 𝑝𝑒𝑎𝑘

𝑉𝑂 = √2𝑔𝑠

1
𝑆 = √2𝑔𝑠(3) − 𝑔(3)2
2
168
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
1
𝑆 = √2(9.81)(𝑠)(3) − (9.81)(3)2
2

∴ 𝑺 = 𝟒𝟒. 𝟏𝟒𝟓

11. What is a substance that speeds up chemical reaction without itself undergoing a
chemical change?
A.Ingredients B. Reactants C.Solvent D.Catalyst

12. If escaping ammonia gas can be smelled across a room in 5.00 minutes, how long
would it take to smell chlorine gas under identical conditions?
A.8.6min B.9.3min C.10.2min D.11.4min

Solution:

𝑀𝑊2/𝑀𝑊1 = (𝑡2/𝑡1)
𝒕𝟐 = 𝟏𝟎. 𝟐𝒎𝒊𝒏
13. A spring with constant of 500 N/m stretched 100mm. How much force is exerted and
how much work. Is done?
A.50 N, 25 J B.5 N, 2.5 J C.5 N, 25 J D.50 N, 2.5 J

Solution:

𝐹 = 𝑆𝑡𝑟𝑒𝑠𝑠 × 𝐴𝑟𝑒𝑎
= (500𝑁/𝑚)(100 × 10^ − 3𝑚)
𝑭 = 𝟓𝟎𝑵
14. In EPIRA, what does OARC stands for?
A.Open Access and Retail Competitors
B.Open Access and Retail Competition
C.Open Access and Retailing Competitors
D.Open Access and Retailing Competition

15. A software that is commonly known as firmware.


A.OS B.Cache memory C.BIOS D.IO

16. What is the minimum lighting load required by PEC for an office measuring 20m by
25m?
A.6000 VA B.7000 VA C.12000 VA D.14000 VA

17. What is the risk is operating a restaurant?

169
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. safe B. neutral C. ambivalent D. risky

18. What is the factor name for the formula (1+i)-n?


A.Uniform gradient future worth C.Single payment present worth
B.Capital recovery D.Single payment compound amount

19. At what point is the applied force minimal in opening a hinge door?
A.near the hinge C.at the center
B.farthest the hinge D.anywhere

20. What do you call negative gage pressure?


A. vacuum B. negative gage C. negative vacuum D. pressure head

21. Common cause of failure of termination of cable.


A. Splicing C.penciling of insulation
B.Clearances D.none of these

22. What is the acid concentration of Nitric acid, HN03 with pH value of -0.55?
A.2.33 M B.4.55 M C.5.33 M D.3.55 M

Solution:

𝑀𝑜𝑙𝑎𝑟𝑖𝑡𝑦 = 𝑎𝑐𝑖𝑑 𝐶𝑜𝑛𝑐𝑒𝑛𝑡𝑟𝑎𝑡𝑖𝑜𝑛


𝑆𝑖𝑛𝑐𝑒 𝐻𝑁𝑂3 𝑖𝑠 𝑎 𝑠𝑡𝑟𝑜𝑛𝑔 𝐴𝑐𝑖𝑑 (𝐻+) 𝑜𝑟 𝑚𝑜𝑙𝑎𝑟𝑖𝑡𝑦
𝐹𝑜𝑟𝑚𝑢𝑙𝑎: 𝑝𝐻 = −𝑙𝑜𝑔(𝐻+)
−0.55 = −𝑙𝑜𝑔(𝐻+)
𝑯+ = 𝟑. 𝟓𝟒𝟖𝟏𝟑𝑴 𝒐𝒓 𝟑. 𝟓𝟓𝑴
23. A projectile is fired at the top of a building at an angle of 20 degrees below the
horizontal. If the muzzle velocity of the projectile is 8 m/s, how high is the building if
the projectile reaches the ground after 3 s?
A.35.94m B.48.89m C.52.35m D.23.62m

Solution:

𝑦 = 𝑉0 sin 𝜃 𝑡 − 1⁄2 𝑔𝑡 2
𝑦 = (8 sin 20)(3) − 1⁄2 (9.81)(3)2
𝒚 = 𝟑𝟓. 𝟗𝟒 𝒎

170
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
24. Two steel plates are joined by using four-10mm rivets. What is the minimum force
that can be applied at these plates without exceeding an allowable shearing stress
of 125 MPa?
A.9.82kN B.39.27kN C.78.54kN D.92.63Kn

Solution:

𝑃
𝜏= 𝐴
𝑃
125𝑥106 = 𝜋 10 2
; 𝑷 = 𝟑𝟗. 𝟐𝟕 𝑲𝑵
4 ( )
4 1000

25. What power in kW is supplied to a 12.0-hp motor having an efficiency of 90.0


percent when it is delivering its full rated output?
A.10.72 B.10.27 C.9.95 D.9.59

Solution:

𝐹𝑜𝑟𝑚𝑢𝑙𝑎 = 𝑛% = 𝑃𝑜𝑢𝑡/𝑃𝑖𝑛 𝑥100


90 = 12𝑥746/𝑃𝑖𝑛 𝑥100
𝑃𝑖𝑛 = 𝟗𝟗𝟒𝟔. 𝟔𝟔𝟔 𝑾 𝒐𝒓 𝟗. 𝟗𝟓 𝑲𝑾
26. A certain water faucet has 7 gpm flow rate. How many minutes can it fill a cubic
meter drum?
A.43.8 B.46.2 C.32.2 D.37.7

Solution:

𝐶𝑜𝑛𝑣𝑒𝑟𝑠𝑖𝑜𝑛 1 𝑔𝑎𝑙 = 0.00379 𝑚3


(1 𝑚^3)/7𝑔𝑝𝑚 𝑥 (1 𝑔𝑎𝑙)/(0.00379 𝑚^3 ) = 𝟑𝟕. 𝟔𝟗𝟑𝟏𝟕𝟓 𝒎𝒊𝒏
27. What is the accumulated amount of P 500 after 6 months, with interest rate 3% per
month?
A.P 597.03 B.P 579.03 C.P 492.05 D.P 429.05
Solution:

𝐴 = (𝑅 + 1)𝑛 𝑥 𝑃
𝐴 = (0.03 + 1)6 𝑥 500 = 𝟓𝟗𝟕. 𝟎𝟑
28. Two equal forces act on a body. F1 being due north and F2 duel east. To have a
net force of zero, at what direction should F3 act?
A.SE B.NE C.SW D.NW
171
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

29. A newly hired electrical engineer is considering the purchase of a motor as his
service vehicle. Package 1: monthly installment of P1, 400.00 at 1% interest rate
effective monthly for 5years and Package 2: Lump sum payment of P68, 000.00
now. He chose package 2, for his option, is he forfeited or not bu how much?
A.P5, 062 loss B.P23, 417 loss C.P23, 417 gain D.P5, 062 gain

Solution:

𝑃𝑉 𝑜𝑓 𝐴𝑛𝑛𝑢𝑖𝑡𝑦 = 𝑃((1 − (1 + 𝑟)^(−𝑛))/𝑟)


𝑃𝑉 𝑜𝑓 𝐴𝑛𝑛𝑢𝑖𝑡𝑦 = 1,400((1 − (1 + 0.01)^(−60))/0.01)
= 62937.05377 – 68000
𝑷𝑽 𝒐𝒇 𝑨𝒏𝒏𝒖𝒊𝒕𝒚 = 𝟓𝟎𝟔𝟐. 𝟗𝟒 𝒍𝒐𝒔𝒔
30. A businessman owes $ 5, 000 cash via his credit card. He can repay this amount at
$100.00 per month paying an interest of 18% compounded monthly. How many
months will these payments be?
A.96 B.93 C.90 D.87

Solution:

𝑃𝑉 𝑜𝑓 𝐴𝑛𝑛𝑢𝑖𝑡𝑦 = 𝑃((1 − (1 + 𝑟)^(−𝑛))/𝑟)


5000 = 100 [(1 − (1 + 0.18/12 )^(−𝑛))/(0.18/12)]
𝒏 = 𝟗𝟑. 𝟏𝟏
31. A thin-walled spherical shell contains a liquid, if it undergoes a thermal coefficient of
linear expansion 𝛼 and subjected to a temperature change of ∆𝑇. What is the ration
of change in volume ∆𝑉 to the original volume V?
A. ∆𝑇/3𝛼 B. 3𝜶∆T C. 3∆𝑇/𝛼 D. 3𝛼T/2

32. Two blocks of wood of 50mm wide and 20mm thick are glued together are shown in
the figure. Using the free body diagram concept, determine the shear load and from
it the shearing in the glued joint if P = 6000 N.

172
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. 3 MPa B. 3.2 MPa C. 2.0 MPa D.2.8 MPa
Solution:
𝐹 6000
𝜎𝑠 = = = 𝟐 𝑴𝑷𝒂
𝐴 (50 𝑋 60)

33. Calculate the word done by a piston if the 2 cu. m. volume of air is tripled while the
temperature is maintained at 40 deg C. The initial pressure is 400kPa.
A. 879 kJ B. 897 kJ C. 766 kJ D. 786 kJ

Solution:

𝑉
𝑊 = 𝑃1 𝑉1 𝑙𝑛 [ 2 ]
𝑉1
3𝑉
𝑊 = (400)(2) ln [ 𝑉 1 ]
1
𝑾 = 𝟖𝟕𝟗 𝒌𝑱

34. An automobile is traveling at 25 m/s. it takes 0.3 s to supply the brakes after which
the deceleration is 6.0 m/s^2. How far does the automobile travel in meters, before it
stops?
A. 40 B. 45 C. 50 D. 60
Solution:

𝑆𝑇 = 𝑆1 + 𝑆2
𝑉𝑓 2 −𝑉𝑜 2
𝑆= 2𝑎

252
𝑆𝑇 = (25)(0.3) +
(2)(6)
𝑺𝑻 = 𝟓𝟗. 𝟓𝟖 𝒎

35. The amount of lateral strain in a tension member can be calculated using
A. the bulk modulus B. Poisson’s ratio C. the yield stress D. Hooke’s law

36. It is the price a buyer is willing to pay a willing seller for the stock.
A. Bond value B. Scrap value C. Market value D. Stock value

37. Your perfectly reliable friend, Marie, asks for a loan and promises to pay back $ 150
two years from now. If the minimum interest rate you will accept is 8%. What is the
minimum amount you will loan him?
A. $ 119 B. $ 126 C. $ 129 D. $ 139

Solution:
173
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑃 = 𝐹(1 − 𝑖)−𝑛
𝑃 = 150 (1 − 0.07)−2
𝐏 = $ 𝟏𝟐𝟖. 𝟔 𝐨𝐫 $ 𝟏𝟐𝟗
38. Find the allowable load, in kN, on a 2-cm dia. 1-m long, steel rod if its elongation
cannot exceed 0.1 cm.
A. 35 B. 45 C. 55 D. 66

Solution:

𝑃𝐿
𝛿 = 𝐴𝐸
1 𝑃(1)
=
100 𝜋 2 2
(200𝑥109 )
4 (100)
𝑷 = 𝟔𝟑 𝒌𝑵 ≈ 𝟔𝟔𝒌𝑵

39. A cold tire has a volume of 0.03 cu. m. at -10 deg C and 180 kPa gage. If the
pressure and temperature increase to 210 kPa gage and 30 deg C, find the final
volume in cu. m.
A. 0.0304 B. 0.0308 C, 0.0312 D. 0.0316

Solution:

𝑃1 𝑉1 𝑃2 𝑉2
=
𝑇1 𝑇2

(180 + 101.325)(0.03) (210 + 101.325)(𝑉2 )


=
−10 + 273 30 + 273
𝟑
𝑽𝟐 = 𝟎. 𝟎𝟑𝟏𝟐 𝒎

40. The minimum size of a copper equipment grounding conductor required for
equipment connected to a 40 ampere circuit.

A. 5.5 sq. mm. B. 8.0 sq. mm. C. 14 sq. mm. D. 22 sq. mm.
41. A pressure of 500 kPa applied to 2 cu, m. of liquid results in a volume change of
0.004cu m. the bulk modulus in MPa, is.
A.2.5 B.25 C.250 D.2500

Solution:

174
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Δ𝑡𝑒𝑚𝑝𝑒𝑟𝑎𝑡𝑢𝑟𝑒
𝐵= 𝑥 𝑣𝑜𝑙𝑢𝑚𝑒
Δ𝑣𝑜𝑙𝑢𝑚𝑒

500 𝑘𝑃𝑎
𝐵= 3
𝑥 2 m3
0.004 m
𝑩 = 𝟐𝟓𝟎 𝑴𝑷𝒂
42. A single grounding electrode is permitted when the resistance to ground does not
exceed.
A.5 ohms B.10ohms C.15ohms D.25ohms

43. An object weighs 100 N in air and 25 N when submerged in water. Its specific gravity
is.
A.1.11 B.1.22 C.1.33 D.1.44
Solution:

100𝑁 − 25𝑁 = 75𝑁 𝑜𝑓 𝑤𝑎𝑡𝑒𝑟


7.65 𝑘𝑔
𝑉= = 7.65 𝑥10−3
1000 kg/ m3

1333.33
𝑆𝑔 = = 𝟏. 𝟑𝟑
1000 kg/ m3

44. A steel cube is subjected to a hydraulic pressure of 1.5 MPa. Because of this
pressure the volume decreases to give a dilatation of -10-5. The young’s modulus of
the material is 200 GPa. Determine the bulk modulus.
A.190GPa B.200GPa C.150GPa D.160GPa

Solution:
1.5 𝑥106
−10−5 = 200(109 ) (1 − 2𝜇)

𝜇 = 0.278
𝜏 200
𝛽= =
3(1 − 2𝜇) 3(1 − 2(0.278))

𝜷 = 𝟏𝟓𝟎 𝑮𝑷𝒂
45. the most important element that controls the physical properties of steel is
A. Silicon B. Tungsten C. Manganese D. Carbon

46. A cantilever beam 10ft long is subjected to a uniformly distributed load of 1500 lb.
per ft. of length. The allowable working stress in either tension or compression is
175
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
20,000 psi. If the cross-section is to be rectangular, determine the height if the height
is to be twice as great as the width.
A.4.62in B.9.24in C.4.06in D.8.12in

Solution:

47. The work of polytrophic (n=1.21) compression of air (C2/C1=1.4) in a system with
moving boundary from P1=15 psia, V1=1.0 cu. ft. to P2150 psia, V2=0.15 cu. ft. is?
A.6862 ft-lb B.1080 ft-lb C.2700 ft-lb D.5150 ft-lb

Solution:
𝑷𝟐 𝑽𝟐 −𝑷𝟏 𝑽𝟏
𝑾= 𝟏−𝒏
(150)(144)(0.15) − (15)(144)(1)
𝑊=
1 − 1.21
∴ 𝑾 = 𝟓𝟏𝟒𝟐. 𝟖𝟔 𝒇𝒕 − 𝒍𝒃

48. How much should you put into a 10% savings account in order to have P10, 000 in
five years?
A.P6, 210.00 B.P7, 000.00 C.P7, 209.00 D.P8, 200

Solution:

𝑖 = 10%, 𝑛 = 5 𝑦𝑟𝑠. , 𝐹 = 𝑃10000


10000 = 𝑋 (1 + .10)5
𝑋 = 𝑷𝟔, 𝟐𝟎𝟗. 𝟐𝟏𝟑𝟐𝟑𝟏 ≈ 𝑷𝟔, 𝟐𝟏𝟎. 𝟎𝟎
49. Gross profit, sales less cost of goods sold, as a percentage of sales is called:
A.ROI ratio B. Profit margin C. gross margin D. Price earnings

50. _____________is regarded as father of computers.


A. Pascal B. John Napler C. Charles Babbage D. Abacus

51. At what angle above the horizontal must the sun be in order that sunlight reflected
from the surface of a calm body of water shall be completely polarized?
A. 60 deg B. 30 deg C. 63 deg D. 37 deg

Solution:
𝑛2
𝑡𝑎𝑛𝜃 = 𝑛1

176
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑛2 = 1.0
𝑛1 = 1.33
1.0
𝜃 = 𝐴𝑟𝑐𝑡𝑎𝑛 1.33

𝜃 = 36.93 deg 𝑜𝑟 𝟑𝟕 𝒅𝒆𝒈


52. In electrochemistry, oxidation is a loss of _____________.
A. ion B. electron C. proton D. anode

53. How many moles of hydrogen atoms are present in 2,000 moles of ammonia?
A. 2 B. 3 C. 6 D.8

Solution:

2000 𝑥 3 = 𝟔𝒎𝒐𝒍𝒆𝒔
54. How long will it take to sink an open and empty vessel 4 m x 4 m x 2m high, with a
draft of 1.6 m, when 85 mm Ф dia, hole at it bottom is opened C= 0.75.
A. 135 sec B. 268 sec C. 311 sec D. 220 sec

Solution:

𝐴𝑟𝑒𝑎 𝑜𝑓 𝑡𝑎𝑛𝑘 = 4𝑚 𝑥 4𝑚 = 16 𝑠𝑞. 𝑚


𝜋
𝐴𝑟𝑒𝑎 𝑜𝑓 ℎ𝑜𝑙𝑒 = (.085)2 = 5.67𝑥10−3 𝑠𝑞. 𝑚
4

ℎ2 = 2𝑚, ℎ1 = 1𝑚
𝐶 = .75
2𝐴𝑡𝑎𝑛𝑘
𝑡 = 𝐶𝐴ℎ𝑜𝑙𝑒(√2𝑔) (√ℎ2 − √ℎ1)

2(16)
𝑡= (√2 − √1.6) = 𝟐𝟔𝟖 𝒔𝒆𝒄
(.75)(5.67𝑥10−3 (√2(9.81)

55. If a disturbance is parallel to the direction of travel of a wave, the wave is classified
as
A. longitudinal B. electromagnetic C. transverse D. torsional

56. If an amount invested five years ago has doubled, what is the annual interest rate?
A. 15% B. 12% C. 10% D. 6%

Solution:

𝑃=𝑃

177
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐹 = 2𝑃
𝑛=5
𝐹 = 𝑃(1 + 𝑖)𝑛
2𝑃 = 𝑃(1 + 𝑖)5
𝑖 = 0.148 𝑜𝑟 . 𝟏𝟓
57. Write the correct formula for ammonium sulfate.
𝐴. 𝐴𝐼3 𝑆𝑂4 𝐵. 𝐴𝐼2 𝑆𝑂4 𝐶. 𝐴𝐼3 (𝑆𝑂4 ) 2 𝑫. 𝑨𝑰𝟐 (𝑺𝑶𝟒 ) 𝟑

58. A man paid 10% down payment of 200,000 for a house and lot and agreed to pay
the balance on monthly installments for 5 years at an interest rate of 15%
compounded monthly. What is the monthly installment in pesos?
A. 44,628.33 B. 42,281.87 C.43, 625.92 D.45, 325.62

Solution:

𝐵𝑎𝑙𝑎𝑛𝑐𝑒 = 200000𝑥9 = 1800000


𝐹 = 𝑃(1 + 𝑖)𝑛
.15 5𝑥12
𝐹 = 1800000 (1 + 12 ) = 3792926.42
𝑖
𝐹 = 𝐴[(1+𝑖)𝑛−1]

.15
12
𝐹 = 1800000 [ .15 5𝑥12
] = 𝟒𝟐𝟖𝟐𝟏. 𝟖𝟕
(1+ ) −1
12

59. Energy is added to a piston-cylinder arrangement, and the piston is withdrawn in


such a way that the quantity PV remains constant. The initial pressure and volume
are 200 kPa, calculate the work done by the gas on the piston.
A. 277 kJ B. 288 kJ C. 399 kJ D. 322 kJ

Solution:

𝑃1 = 200 𝑘𝑃𝑎, 𝑃2 = 100 𝑘𝑃𝑎, 𝑉1 = 2 𝑐𝑢. 𝑚


𝑃
𝑊 = 𝑃1 𝑉1 𝑙𝑛 𝑃2
1

200
𝑊 = (200)(2)𝑙𝑛 100 = 277258 𝑃𝑎 𝑜𝑟 𝟐𝟕𝟕 𝒌𝑷𝒂

60. Calculate the volume occupied by 0.151 mol of 𝐶𝐼2 at 100 deg C and 73.7 kPa.
A. 3.56 L B. 6.35 L C. 4.28 L D. 5.82 L
178
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:

𝑃𝑉 = 𝑛𝑅𝑇
𝑛𝑅𝑇
𝑉= 𝑃
(.151)(8.21)(100+273)
𝑉= = 6.35−3 𝑐𝑢. 𝑚
73.7𝑥1000
1000𝐿
𝑉 = 6.35−3 𝑐𝑢. 𝑚 𝑥 = 𝟔. 𝟑𝟓𝑳
1 𝑐𝑢.𝑚

61. A 500 N body initially at rest is acted upon for 9 seconds by a variable force F =100
(sq rt of t), and also by a variable resisting force F=30 – t during that time. What is its
velocity at the end of 9 seconds?
A. 22.68 m/sec B. 24.82 m/sec C. 30.78 m/sec D.36.76 m/sec
Solution:

𝐹1 = 100 √𝑡

𝑓2 = 30 – 𝑡

F−F2
𝑉= g
w

1800−229.5
𝑉= (9.8)
500

∴ 𝑽 = 𝟑𝟎. 𝟕𝟖 𝒎/𝒔𝒆𝒄

62. A refrigerator is rated at COP of 4. The refrigerated space that it cools requires a
peak cooling rate of 30,000 kJ/h. What size of electrical motor (rated in horsepower)
is required for the refrigerator?
A. 1.968 hp B. 4.624 hp C. 1.937 hp D. 2.793 hp

Solution:
𝑘𝐽 1ℎ𝑟
𝑃 = 30,000 ℎ𝑟. × 3600 𝑠𝑒𝑐

𝑃 = 8.333 𝑘𝑊

p 8.333 kw .746 hp
𝑃 = COP = ×
4 1kw

179
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑷 = 𝟐. 𝟕𝟑𝟗 𝑯𝒑

63. A simply supported wooden beam 4 m span is 100 mm wide by 200 mm deep. It
carries a load of 1.5 kN/m run over its entire spam. Taking E as 8 x 10^3 MPa, find
the central deflection of the beam.
A. 9.375 mm B. 9.735 mm C. 8.325 mm D. 8.235 mm
Solution:

5WL⁴
𝛿=
384EI
Bhᵌ (0.1)(0.2)ᵌ
𝐼= 𝐼=
12 12

I = 6.67×10 ‫־‬⁵

5(1.5×10ᵌ)(4)⁴
𝛿= 5
384(8×10⁹)(6.67×10‫) ־‬

𝜹 = 𝟗. 𝟑𝟕𝟓𝒎𝒎

64. A baseball is thrown with an initial velocity of 100 m/s at an angle of 30 degrees
above the horizontal. How far from the throwing point will the baseball attain its
original level?
A.878 m B. 890 m C. 884m D. 862 m

Solution:
Vo²sin2θ 100²sin(60)
𝑅= =
g 9.8

𝑹 = 𝟖𝟖𝟒 𝒎

65. A ladder 3.0 m long and weighing 200 N has its center of gravity 1.2 m from the
bottom. At its top end is a 50 N weight. Compute the work required to raise the
ladder from a horizontal position on the ground to a vertical position.
A. 0.24 kJ B. 0.39 kJ C. 0.15 kJ D. 0.63 Kj

Solution:

∑𝑀 = 0

𝑊 = 200(1.2) + 50(3) = 𝟎. 𝟑𝟗 𝑲𝑱
180
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
66. The viscosity of fluid varies with
A. temperature C. density
B. pressure D. temperature and pressure

67. Water at 20 deg C will rise, in a clean 1-mm dla glass tube, a distance, in cm, of
A. 1 B.2 C. 3 D. 4

Solution:
4Ϭcosθ
ℎ= Ϭ= 0.0736 @ 20 deg C
ρdg

4(.0736)cos(0)
ℎ = 1000(.001)(9.81)

𝒉 = 𝟑 𝒄𝒎

68. A wheel of mass 6.0 kg and radius of gyration 40 cm is rotating at 300 rpm. Find its
rotational KE.
A. 0.26 kJ B. 0.62 kJ C. 0.78 kJ D. 0.47 kJ

Solution:
1
𝐾𝐸 = 2MV²

300(2л×40)
𝑉= = 4л m/sec
60

𝐾𝐸 = ½(6)(4л)²

𝑲𝑬 = 𝟎. 𝟒𝟕 𝑲𝑱

69. Which of the following is NOT a vector quantity?


A. displacement C. speed
B. acceleration D. momentum

70. A car has wheels of radius 30 cm. It starts from rest and accelerates uniformly to a
speed of 15 m/s in a tire of 8.0 s. Find the number of rotations one wheel make in
this time.
A. 42 rev B. 34 rev C. 36 rev D. 32 rev

Solution:
S
𝑛=C S= ½(15)(8)

S= 60
181
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
60
𝑛=
2л(0.3)

𝒏 = 𝟑𝟐 𝒓𝒆𝒗.

71. The viscosity of a fluid with specific gravity 1.3 is measured to be 0.0034 N-s/sq. m.
Its kinematic viscosity in (sq.m.)/s, is
A. 2.6 x 10^-6 B. 4.4 x 10^-6 C. 5.8 x 10^-6 D. 7.2 x 10^-6
Solution:
V
𝐾𝑉 =
𝑆. 𝐺(1000)
0.0034
𝐾𝑉 =
1.3(1000)
= 𝟐. 𝟔 × 𝟏𝟎‫־‬⁶ m²/sec
72. A copper bar, 70 mm diameter and 1.5 m long has to bear a shock of 40MPa. Find
the change in length. E=110 GPa.
A. 0.455 mm B. 0.545 mm C. 0.345 mm D. 0.654 mm
Solution:
P
𝐹=A

P = (40×10⁶)(л/4)(70×10‫־‬ᵌ)²
P = 49,000л
PL (49000л)(1.5)
ẟ = AE = л/4(76×10ᵌ)²(40×10⁹)

ẟ = 𝟎. 𝟓𝟒𝟓 𝒎𝒎
73. A rubber band has an unstretched length of 180 mm. If it is stretched around a pole
having a diameter of 60 mm, determine the average normal strain in the band.
A. 0.0427 B. 0.0236 C.0.0263 D.0.0472

Solution:
ẟL
𝜀=
𝐿

60л−180
𝜀=
180

𝜠 = 𝟎. 𝟎𝟒𝟕𝟐

74. A device used to keep moisture from passing through the system is called:

182
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. trap B. aerator C. humidifier D. dehydrator

75. A stone of mass 00 grams is wired in a horizontal circle at the end of a cord 100 cm
long. If the tension in the cord is 2.5 newtons, what is the speed of the stone?
A. 3 m/s B. 4 m/s C. 5 m/s D. 6 m/s

Solution:
√𝐹𝑟
𝑉=
√𝑚

√(2.5)(1)
𝑉=
√0.1

𝑽 = 𝟓 𝒎/𝒔𝒆𝒄

76. The maintenance costs associated with a machine are $2,000 per year for the first
ten years, and $1,000 per year thereafter. The machine has an infinite life. If interest
is 10%, what is the present worth of the annual disbursements?
A. $16,145 B. $19,678 C. $21,200 D. $92,136

Solution:
F A[1−(1+i)‫־‬ⁿ]
𝑃 = i (1 + 𝑖)‫־‬ⁿ + i

1000 2000[1−(1+0.1)‫־‬¹°]
𝑃 = 0.1(1+0.1)¹° + 0.1

𝑷 = $𝟏𝟔, 𝟏𝟒𝟓

77. A railway gun whose mass is 70,000 kg fires a 500-kg artillery shell at an angle of 45
degrees and with a muzzle velocity of 200 m/sec. Calculate the recoil velocity of the
gun.
A. -3 m/s B. -4 m/s C. -1 m/s D. -2 m/s

Solution:
𝑚2𝑣2𝑐𝑜𝑠𝜃
𝑉1 =
m1 + m2

(500)(200)𝑐𝑜𝑠(45)
𝑉1 =
(500) + (70,000)

𝑉1= 1 m/sec (direction to the left)

183
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
= −𝟏 𝒎/𝒔𝒆𝒄

78. A square steel bar 50 mm on a side and 1 m long is subject to an axial tensile force
of 250 kN. Determine the decrease in the lateral dimensions due to this load.
Consider E=200 GPa and µ= 0.3.
A. 5.7 x 10^-3 mm B. 7.5 x 10^-3 mm
C. 6.5 x 10^-3 mm D. 6.7 x 10^-3 mm

Solution:
PuD
ẟᵈ =
AE
(250×10ᵌ)(0.3)(0.05)
ẟᵈ =
(50×10‫־‬ᵌ)²(200×10⁹)

ẟᵈ = 𝟕. 𝟓 × 𝟏𝟎‫־‬ᵌ 𝒎𝒎
79. It is a process of mixing water with air either by spraying water or diffusing air
through it.
A. aeration B. coagulation
C. infiltration D. evaporation

80. A pipe 60 cm in length is connected at the end by a nozzle and the total energy
produce in the nozzle is 250 cm. Compute the velocity of the jet.
A. 90 m/s B. 80 m/s C. 60 m/s D. 70 m/s

Solution:

1𝑚
𝐿 = 60 𝑐𝑚 𝑥 = 0.6 𝑚
100 𝑐𝑚
1𝑚
𝑁 = 250 𝑐𝑚 𝑥 = 2.5 𝑚
100 𝑐𝑚
𝑉2
𝑒𝑛𝑒𝑟𝑔𝑦 = 2𝑔
𝑉2
250 = 2(9.81)
𝒎
∴ 𝑽𝟐 = 𝟕𝟎. 𝟔𝟑
𝒔
81. A drill press is purchased for $10,000 and has an estimated life of twelve years. The
salvage value at the end of twelve years is estimated to be $1,300. Using general
straight-line depreciation, compute the book value of the drill press at the end of
eight years.
A. $ 1,200 B. $3,333 C. $3,475 D. $ 4, 200

Solution:

184
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑪𝒐 − 𝑪𝒏
𝒅= 𝒏
10,000− 1300
𝑑= 12
𝑑 = 725
𝑫𝒎 = 𝒎𝒅
𝐷𝑚 = (8)(725)
𝐷𝑚 = 5800
𝐶𝑚 = 𝐶𝑂 − 𝐷𝑚
𝐶𝑚 = 10,000 − 5800
∴ 𝑪𝒎 = 𝟒𝟐𝟎𝟎

82. It is required to transmit 70 hp from a turbine by a solid circular shaft turning at 200
r/min. If the allowable shearing stress is 7,000 lb/sw in., determine the required shaft
diameter.
A. 3.13 in B. 2.52 in C. 1.12 in D. 2.12 in

Solution:

2𝜋𝑁𝑇
𝐷= 33,000
70(33,000)
𝑇= = 1838.24
2𝜋(200)
16𝑇
𝑆=
𝜋𝑑 3
16(1838.24)
7000 =
𝜋𝑑 3
𝒅 = 𝟏. 𝟏𝟐 𝒊𝒏

83. What is the friction factor for fully developed flow in a circular pipe where Reynolds
number is 1000?
A. 0.08 B. 0.054 C. 0.8 D. 0.064

Solution:

64 64
𝒇= = = 𝟎. 𝟎𝟔𝟒
𝑅𝑒 1,000

84. A manufacturing firm wishes to give each 80 employees a holiday bonus. How mch
is needed to invest monthly for a year at 12% nominal interest rate compounded, so
that each employee will receive a P2, 000 bonus?
A. P 12,615.80 B. P 12, 516.80 C. P 12,611.80 D.P 12,510.80

Solution:

185
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
0.12
𝑖= = 0.01
12
𝑛 = 12
𝐹 = 80(2000) = 160,000
𝐴[(1 + 𝑖)𝑛 − 1]
𝐹=
𝑖
𝐴[(1 + 0.01)12 − 1]
160,000 =
0.01
𝑨 = 𝟏𝟐, 𝟔𝟏𝟓. 𝟖𝟎
85. A tank contains of oil sp. Gr. = 0.80, gasoline and sp. Gr. = 0.90 and sea water sp.
Gr. =1.03. If the depths of the liquids are 0.5 m, 0.8 m, and 1 m for oil, gasoline and
sea water respectively. Find the pressure at a depth of 1.8 m.
A. 10.104 Kpa B. 16.04 kPa C. 21.092 kPa D. 24.089 kPa

Solution:

𝑷𝟐 = 𝑷𝟏 + 𝜺𝜸𝒉
𝑃2 = 0.80 (9.81)(0.5) + (0.90)(9.81)(0.8) + (1.03)(9.81)(0.5)
𝑷𝟐 = 𝟏𝟔. 𝟎𝟒 𝒌𝑷𝒂
86. An asset was purchased for P100, 000 and retired at the end of 15 years with a
salvage value of P 4,000. The annual operating cost was P 18,000. Determine the
capitalized cost of the asset based on an interest rate of 8%.
A. 369,195 B. P396,195 C. P468,285 D. P 486,285

Solution:

𝑪𝑪 = 𝑪𝟎 + 𝑨
𝐶𝐶 = 100,000 + (18,000 𝑥 15)
𝑪𝑪 = 𝟑𝟕𝟎, 𝟎𝟎𝟎 ≈ 𝟑𝟔𝟗, 𝟏𝟗𝟓

87. Car A has a mass of 1000 kg and a speed of 60 km/h and car B has a mass of 2,000
kg and a speed of 30 km/h. The kinetic energy of car A is
A. half that of car B C. twice that of car B
B. equal to that of car B D. four times of that car B

Solution:
1
𝐾𝐸 = 𝑚𝑣 2
2

186
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
1
𝐶𝑎𝑟 𝐴 = (1000)(60)2 = 𝟏, 𝟖𝟎𝟎, 𝟎𝟎𝟎 𝐉
2
1
𝐶𝑎𝑟 𝐵 = (2000)(30)2 = 𝟗𝟎𝟎, 𝟎𝟎𝟎 𝐉
2
𝑨𝒏𝒔𝒘𝒆𝒓: 𝑻𝒉𝒆 𝒌𝒊𝒏𝒆𝒕𝒊𝒄 𝒆𝒏𝒆𝒓𝒈𝒚 𝒐𝒇 𝒄𝒂𝒓 𝑨 𝒊𝒔 𝒕𝒘𝒊𝒄𝒆𝒆 𝒕𝒉𝒂𝒕 𝒐𝒇 𝒄𝒂𝒓 𝑩

88. A temperature of 100 deg F is almost exactly


A. 38 deg C B. 56 deg C C. 122 deg C D. 212 deg C

Solution:
5
𝑇𝑐 = (100 deg 𝐹 − 32) x = 𝟑𝟕. 𝟕𝟕𝟖 𝐝𝐞𝐠 𝑪
9
89. Battery acid is the is the common name for
A. formic acid B. hydrochloric acid C. nitric acid D. sulfuric acid

90. Which of the following engines is normally the least efficient?


A. gasoline engine C. gas turbine
B. diesel engine D.Carnot engine

91. Electrical symbol represented by a broken line


A. Open wiring B. Circuit homerun
C. Underground wiring D. Emergency wiring

92. Which of the following is not a unit of power?


A. joule-second C. newton-meter per second
B. watt D. horsepower

93. Which of the following is not a unit of power?


A. joule-second C. newton-meter per second
B. watt D. horsepower

94. RA 7920, Rule 2 (d) defining?


A. CHED B. Commission
C. Board of EE D. TESDA

95. Neglecting the change of gravity with elevation, estimate the speed of a satellite
must have to orbit the earth at an elevation of 100 km. Earth’s radius =6,4oo km.
A. 4,000 B. 6,000 C. 8,000 D. 10,000

Solution:

𝑉 = √𝐹𝑑
187
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

𝑉 = √(9,810)(6400 + 100)

𝑽 = 𝟕𝟗𝟖𝟓. 𝟑𝟎 ≈ 𝟖, 𝟎𝟎𝟎

96. Which of the following sizes of fuse is NOT standard?


A. 60 A B. 45 A. C. 125A D. 75A

97. The maximum allowable shear stress in a 10-cm diameter shaft is 140 mPa. What
maximum torque, in N-m, can be applied?
A. 27,500 B. 21,400 C. 19,300 D. 17,100

Solution:
Ꝭ(л𝐷ᵌ)
𝑇= 16

(140 × 10⁶)(л)(0.1)ᵌ
𝑇=
16

𝑻 = 𝟐𝟕, 𝟓𝟎𝟎 𝑵 − 𝒎

98. What is the temperature rating of THHN insulation?


A. 60 deg C B. 90 deg C C. 85 deg C D. 75 deg C

99. Compute the maximum possible efficiency of a heat engine operating between
temperature limits of 100 deg C and 400 deg C.
A. 44.6% B. 46.8% C. 75% D. 95%

Solution:
𝑇𝐻−𝑇𝐿 400−100
𝑒𝑓𝑓 = = 400+273 × 100%
𝑇𝐻

eff = 44.6 %

100. In a car which is decelerating, a plumb line hanging from the roof maintains a
constant angle of 30 degrees with the vertical. What is the acceleration value?
A. 17.82 ft/sec^2 C. 55.43 ft/sec^2
B. 18.47 ft/sect^2 D. 54.32 ft/sec^2

Solution:

𝑎= 𝑟

188
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

𝒕𝑎𝑛 𝜃 = 𝑔𝑟

a = gtanθ
a = 32.2 (tan 30)
a = 18.59 ft/sec²

189
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
ESAS PRE-BOARD EXAM MARCH 2013

1. The reservoir dam holds an 800-km2 lake behind it. Just behind the dam the lake is
12.0m deep. What is the water pressure of the base of the dam?
A. 29 kPa B. 118 KP C. 89 KPa D. 147 KPa

Solution:

𝑃 = (1000𝐾𝑔/𝑚3)(9.81𝑚/𝑠2)(12𝑚)
𝑃 = 117.7 𝑜𝑟 𝟏𝟏𝟖𝒌𝑷𝒂

2. A skier starts from rest and slides 9.0m down a slope in 3.0s in what time after
starting will the skier a speed of 24m/s? Assume that the acceleration is constant.
A. 12 s B. 1.1s C. 10s D. 9s
Solution:
2(9) 24
𝐴= = 2𝑚/𝑠2 𝑡 = = 𝟏𝟐𝒔𝒆𝒄.
32 2

3. A certain town receives its water directly from a water tower. If the top of the water in
tower is 26.0m above the tower faucet in the house. What should be the water
temperature of the faucet? (neglect the effects of the other water users).
A. 255 KPa B. 265 KPa C. 245 KPa D. 295 KPa
Solution:
𝑃 = (1000) (9.81) (26)
∴ 𝑷 = 𝟐𝟓𝟓. 𝟎𝟔 𝒌𝑷𝒂
4. A type of annuity where the payments are made at the start of each period,
beginning from the first period.
A. Annuity due B. Ordinary Annuity
C. Perpetuity D. Deferred Annuity

5. Two masses m1 = 5kg and m2 = 10kg have velocities v1 = 2 m/sec in the x direction
and v2 = 4 m/sec in the y direction. They collide and stick together. What is their final
velocity after collision?
A. 2.560 m/sec B. 2.850 m/sec
C. 2.750 m/sec D. 3.825 m/sec

Solution:
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
6. If 4.88 g of a gas occupies 2.75L at 103kPa and 22 deg C, calculate the molar mass.
A.24.1 g/mol B. 42.1 g/mol C. 21.4 g/mol D. 12.4 g/mol

Solution:
𝑅
𝑃𝑉 = 𝑚 𝑚𝑤 𝑇
3.75 4.88 8.3144
(101.325) (1000) = 1000 ( ) (22 + 273)
𝑚𝑤

𝒈
𝒎𝒘 = 𝟒𝟐. 𝟏
𝒎𝒐𝒍
7. Oil flows through a 4.0m inside diameter pipe at an average speed of 2.5m/s. Find
the flow in cu. M of water per hour.
A. 2.1x10-3 cu. m/s B. 4.1x10-3cu. m/s
C. 1.10x10-3cu m/s D. 2.1x10-3 cu m/s

Solution:
𝑵𝒐𝒕𝒆: 𝑻𝒓𝒐𝒖𝒃𝒍𝒆𝒔𝒉𝒐𝒐𝒕 𝒑𝒓𝒐𝒃𝒍𝒆𝒎

8. Calculate the number of moles in 4L of a gas mixture at 25 deg C if the total


pressure is 0.995 atm.
A. 0.35mol B. 0.163 mol C. 0.153 mol D. 0.135 mol

Solution:
𝑷𝑽 = 𝒏𝑹𝑻
(0.995)(4) = 𝑛(0.0821)(25 + 273)
∴ 𝒏 = 𝟎. 𝟏𝟔𝟑 𝒎𝒐𝒍
9. Compute the average speed of water in pipe having an inside diameter of 5.0 cm
and delivering 2.5 cu. M of water per hour.
A. 0.35 m/s B 0.20 m/s C. 0.40 m/s D. 0.25 m/s

Solution:
𝑸 = 𝑨𝑽
𝑚3 1 ℎ𝑟 𝜋 5 2
(2 )( )= ( 𝑖𝑛) 𝑉
ℎ𝑟 3600 𝑠𝑒𝑐 4 100

∴ 𝑽 = 𝟎. 𝟑𝟓 𝒎⁄𝒔

191
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
10. The product of force and the time during which it acts is knows as:
A. Momentum B. impact C. impulse D. work

11. Formula of calcium chloride


A. CaCl2 B. Ca2Cl C. CaCl D. CaCl3

12. After how many years will an investment triple 10% per annum, net of deductions,
compounded quarterly?
A. 12.11 B. 11.12 C. 10.16 D. 9.20
Solution:
10%
3 = (1+ 4
)4(𝑛) ; 𝑁 = 𝟏𝟏. 𝟏𝟐𝒚𝒓𝒔

13. What is the branch circuit demand for 12 KW range and 5 KW cooktop?
A. 8 B. 11 C. 10 D. 15

14. Compute the least acceleration with which a 45-kg woman can slide down a rope if
the rope can withstand a tension of only 300N.
A. 9.8 m/s2 B. 16.47 m/s2 C. 1.55 m/s2 D. 3.1m / s2

Solution:
141
441 – 300 = 141𝑁; 𝐴 = = 𝟑. 𝟏 𝒎/𝒔𝟐
45
15. An elevator is pulled by cable at constant speed. The tension in the cable is equal to
A. The weight B. twice the weight
C. thrice the weight D. half the weight

16. P150,000 was invested at 5% compounded monthly, tax free for 10years and 3
months. How much was the capital plus earnings at the end of the period?
A. P250,152 C.P280,348
B. P240,196 D. P360,224

Solution:
5%
𝐹 = 150𝑘 (1 + )2(10.25) = 𝟐𝟓𝟎, 𝟏𝟓𝟐. 𝟒𝟐𝟔
12
17. In a hydraulic press, the small cylinder has a diameter of 8cm, while the larger piston
of the diameter of 22cm, if the force of 600N is applied to the small piston, what is
the force on the larger piston neglecting friction?
A. 3.5KN B. 4.5 KN C. 5.5 KN D. 6.5 KN

192
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

600𝑁/(𝜋/4 (80 ∗ 80) ) = ( 𝑋)/(𝜋/(4(22 ∗ 22)))𝑋


= 4537.5 𝑜𝑟 𝟒. 𝟓𝒌𝑵
18. A baseball is thrown with an initial velocity of 100m/s at the angle of 30 degrees
above the horizontal. How far from the throwing point will the baseball attain its
original level?
A. 788m B. 862m C. 884m D. 766m

Solution:
100𝑠𝑖𝑛30
𝑡= = 10.2 𝑠𝑒𝑐𝑠
9.81
𝑥 = 100 𝑐𝑜𝑠30 10.25 = 𝟖𝟖𝟑. 𝟑
19. Branch circuit larger than ________ ampere shall supply only non-lighting outlet
load.
A. 20 B. 50 C. 15 D. 3

20. Calculate the concentration of a 500-ml solution containing 1.71 mol of solute.
A. 2. 29 M B. 2.92 M C. 4.32 M D. 3.42 M

21. A 1 cu. M tank is filled with a gas at room temperature 20 deg C and a pressure of
100 kPa. How much in there if the gas is propane with R = 0.18855?
A. 1.809 B. 26.515 C. 1.942 D. 2062

Solution:
Using the Ideal Gas Law formula: 𝑃𝑉 = 𝑚𝑅𝑇 , then derived to form the equation:

𝑃𝑉
𝑚=
𝑅𝑇

(100) 𝑥 (1)
𝑚= (0.18855) 𝑥 (20+273)

𝒎 = 𝟏. 𝟖𝟏𝟎 𝒈𝒓𝒂𝒎𝒔 (𝒏𝒆𝒂𝒓𝒆𝒔𝒕)

22. A carnot engine operates between reservoirs at 20 deg C and 200 deg C if 10KW of
power is produced, the rejected heat rate is nearest.
A. 26.3 kJ/s B. 20.2 kJ/s C. 16.3 kJ/s D. 12 kJ/s

Solution:

193
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑇𝐿
𝑈𝑠𝑖𝑛𝑔 𝑡ℎ𝑒 𝐶𝑎𝑟𝑛𝑜𝑡 𝐸𝑓𝑓𝑖𝑐𝑖𝑒𝑛𝑐𝑦 𝑓𝑜𝑟𝑚𝑢𝑙𝑎: Ƞ = (1 − ) ∗ 100%
𝑇𝐻

Ƞ = (1 − 𝑇_𝐿/𝑇_𝐻 ) ∗ 100%

𝑁𝑜𝑡𝑒: 𝑇 𝑚𝑢𝑠𝑡 𝑎𝑙𝑤𝑎𝑦𝑠 𝑒𝑥𝑝𝑟𝑒𝑠𝑠𝑒𝑑 𝑖𝑛 𝑎𝑏𝑠𝑜𝑙𝑢𝑡𝑒 𝑡𝑒𝑚𝑝𝑒𝑟𝑎𝑡𝑢𝑟𝑒 𝑠𝑐𝑎𝑙𝑒 (𝑅 𝑜𝑟 𝐾)

𝑇𝐿 = (20 ℃ + 273) = 293 𝐾

𝑇𝐻 = (200 ℃ + 273) = 473 𝐾

293
Ƞ = (1 − ) ∗ 100%
473

Ƞ = 38.05 %

𝑊 10 𝑥 103
𝑄= = = 26,281.21 𝑊
Ƞ 0.3805

𝑄𝐻 = 𝑄𝑇 − 𝑄𝐿

𝑄𝐻 = 26,281.21 − 10,000

𝒌𝑱
𝑸𝑯 = 𝟏𝟔, 𝟐𝟖𝟏. 𝟐𝟏 𝒐𝒓 𝟏𝟔. 𝟐𝟖 𝒌𝑾 𝒐𝒓 (𝒏𝒆𝒂𝒓𝒆𝒔𝒕)
𝒔

𝑊𝑜𝑟𝑘 (𝑊) 𝑖𝑛 𝐽𝑜𝑢𝑙𝑒𝑠


𝑁𝑜𝑡𝑒: 𝑃𝑜𝑤𝑒𝑟 (𝑃) = 𝑡𝑖𝑚𝑒 (𝑡) 𝑖𝑛 𝑠𝑒𝑐𝑜𝑛𝑑𝑠

23. Oil with specific gravity of 0.80 is 0.91m deep in an open tank which in otherwise
fixed with water. If the tank is 3.05 m deep, what is the temperature in kPa, at the
bottom of the tank?
A. 21.80 B. 27.89 C. 28.10 D. 23.45

Solution:
𝑘𝑔
𝜌𝐻2 𝑂 = 1000 𝑚3

𝜌𝑜𝑖𝑙 = (𝑆. 𝐺𝑜𝑖𝑙 ) 𝑥 (𝜌𝐻2 𝑂 )

𝑘𝑔
𝜌𝑜𝑖𝑙 = (0.80) 𝑥 (1000) = 800 𝑚3

To get the pressure of H2O and oil use the formula: 𝑃 = 𝜌𝑔ℎ

𝑃𝐻2 𝑂 = (1000) 𝑥 (9.81) 𝑥 (2.14) = 20,993.4 𝑃𝑎

194
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑃𝑜𝑖𝑙 = (800) 𝑥 (9.81) 𝑥 (0.91) = 7,141.68 𝑃𝑎

To get the pressure of the bottom, use the formula: 𝑃𝑏𝑜𝑡𝑡𝑜𝑚 = 𝑃𝐻2 𝑂 + 𝑃𝑜𝑖𝑙

𝑃𝑏𝑜𝑡𝑡𝑜𝑚 = 20,993.4 𝑃𝑎 + 7,141.68 𝑃𝑎

𝑷𝒃𝒐𝒕𝒕𝒐𝒎 = 𝟐𝟖. 𝟏𝟒 ≈ 𝟐𝟖. 𝟏𝟎 𝐤𝐏𝐚

24. A man expects to receive P20,000 in 10 years. If the interest is computed at 6%


compounded quarterly, how much is it worth today?
A. P11,025.25 B. P11,035.25
C. P11,045.25 D. P11,055.25

Solution:

𝑟 −𝑚𝑛
Using the formula: 𝑃 = 𝐹 (1 + 𝑚)

0.06 −(4𝑥10)
𝑃 = 20,000 (1 + )
4

∴ 𝑷 = 𝑷𝟏𝟏, 𝟎𝟐𝟓. 𝟐𝟓

25. How many grams are represented in 2.50 mol of H2O?


A. 45 B. 21.7 C. 43.9 D. 32.7

Solution:

First, get the MW or the molecular weight, multiply the atomic weight each
element to their subscript then get the sum. Using the periodic table, the atomic
of H is 1 and O is 16

𝐻2 = 2 𝑥 1 = 2

𝑂 = 1 𝑥 16 = 16

𝑀𝑊 = 18 𝑔𝑟𝑎𝑚/𝑚𝑜𝑙𝑒

Using the formula: 𝑚 = 𝑛 𝑥 𝑀𝑊

𝑚 = (2.50) 𝑥 (18)

𝒎 = 𝟒𝟓 𝒈𝒓𝒂𝒎𝒔

195
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
26. The standard atmospheric pressure in meters of atmospheric is (ρ = 600 kg/ cu. M)
is.
A. 19m B. 31m C. 23m D. 17m
Solution:

𝜌𝐻𝑔
𝑎𝑡𝑚𝑁𝐻3 𝑖𝑛 𝑚𝑒𝑡𝑒𝑟𝑠 = 𝑎𝑡𝑚𝐻𝑔 𝑥 (𝜌 )
𝑁𝐻3

𝑘𝑔
𝑁𝑜𝑡𝑒: 𝜌𝐻𝑔 = 13,600 𝑚3 , 𝑎𝑡𝑚𝐻𝑔 = 0.760 𝑚 𝐻𝑔

13,600
𝑎𝑡𝑚𝑁𝐻3 𝑖𝑛 𝑚𝑒𝑡𝑒𝑟𝑠 = 0.760 𝑥 ( )
600

𝒂𝒕𝒎𝑵𝑯𝟑 𝒊𝒏 𝒎𝒆𝒕𝒆𝒓𝒔 = 𝟏𝟕. 𝟐𝟐 ≈ 𝟏𝟕 𝒎

27. A side (2 in) of a square bar is loaded in tension by a force of 12kips. Determine the
normal stress in ksi in the square bar.
A. 5.5 B. 6 C. 2.6 D. 3
Solution:
𝐹
Using the stress formula: 𝜎 =
𝐴

12,000
𝜎=
4

𝝈 = 𝟑 𝒌𝒔𝒊

28. What is the accumulated amount of five-year annuity paying P6,000 at the end of
each year, with interest rate at 15% compounded annually?
A. P 40,519.21 B. P40,681.29
C. P40,545.29 D. 40,329.10

Solution:
(1+𝑖)𝑛 −1
Using the formula: 𝐹 = 𝐴 [ ]
𝑖

(1+0.15)5 −1
𝐹 = 6000 [ ]
0.15

∴ 𝑭 = 𝑷𝟒𝟎, 𝟒𝟓𝟒. 𝟐𝟗

29. Calculate the strain of for a chance in length = 0.038 cm and a length of 1.90m.
A. 0.000217 B. 0.00020 C. 0.020526 D. 0.000211
Solution:
196
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝛿
𝑈𝑠𝑖𝑛𝑔 𝑡ℎ𝑒 𝑠𝑡𝑟𝑎𝑖𝑛 𝑓𝑜𝑟𝑚𝑢𝑙𝑎: ∈ = 𝐿

𝐶𝑜𝑛𝑣𝑒𝑟𝑡 0.038 𝑐𝑚 𝑡𝑜 𝑚 = 0.00038 𝑚

0.00038
∈=
1.90

∴∈ = 𝟐𝒙𝟏𝟎𝟒 𝒐𝒓 𝟎. 𝟎𝟎𝟎𝟐𝟎

30. A 1.0 slug mass has a kinetic energy of 1.0 ft-lb when its speed is
A. 0.25 ft/s B. 1.0 ft/s C. 1.4 ft/s D. 6 ft/s

Solution:

1 2𝐾𝐸
𝑈𝑠𝑖𝑛𝑔 𝑡ℎ𝑒 𝑓𝑜𝑟𝑚𝑢𝑙𝑎: 𝐾𝐸 = 𝑚𝑣 2 𝑡ℎ𝑒𝑛 𝑑𝑒𝑟𝑖𝑣𝑒 𝑡𝑜 𝑓𝑜𝑟𝑚 𝑡ℎ𝑒 𝑒𝑞𝑢𝑎𝑡𝑖𝑜𝑛: 𝑣 = √
2 𝑚

2𝑥1
𝑣= √ 1

𝒇𝒕
∴ 𝒗 = 𝟏. 𝟒 𝒔

31. How much pressure is needed to raise water to the top of the building which is 1250
ft high?
A. 562 lb/sq. in B. 426 lb/sq. in
C. 542 lb/sq. in D. 462 lb/sq. in

Solution:
𝑙𝑏 𝒍𝒃
𝑃 = (1000)(9.81)(381) = 3.74𝑀𝑃𝑎 𝑡𝑜 2
= 𝟓𝟒𝟐 𝟐
𝑚 𝒊𝒏
32. The following forces act on an object 10 N to the north 20 N to the southeast and 5
N to the west. The magnitude of their resultant is.
A. 5 N B. 10 N C. 13 N D. 23 N

Solution:
𝐹 = |10∠90 + 20 ∠ − 45 + 90 ∠135|
𝑭 = 𝟏𝟎. 𝟔𝟐 𝑵
33. If 200 cc. of a gas weighs 0.266 g at S.T.P. what is its molecular weight?
A. 10 B. 20 C. 30 D. 40

197
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Solution:
𝑆𝑇𝑃 = 22.4𝐿
1
(22.4𝐿 ) ( ) (0.268) = 𝟑𝟎. 𝟑𝟏𝟔
0.20
34. A machine costing P1,800,000 has a life of 8 years. Using straight line method, the
total depreciation at the end of 4th yr. is P800,000. Determine the salvage value of
the machine/
A. P150,000 B. P250,000
C. P300,000 D. P200,000

Solution:
4 ∗ 1.8𝑀 − 𝐶𝑛
800𝐾 =
8
∴ 𝐶𝑛 = 𝟐𝟎𝟎, 𝟎𝟎𝟎
35. The density of zinc is 455 lb/ cu. Ft. find the mass in grams of 9.00 cc of zinc.
A. 65.6 B. 56.5 C. 46.5 D. 85.6
Solution:
𝑙𝑏 𝑘𝑔
𝑃 = 465 3
= 7288.4 2 ; 𝑉 = 9𝐶𝐶 𝑡𝑜 0.009 𝐾𝑔
𝑓𝑡 𝑚
𝑋
7288.4 = ; 𝑋 = 𝟔𝟓. 𝟔
0.009

36. Energy is added to 5kg air with paddle wheel so that ∆T = 100 deg C while P =
constant in an insulated container. The paddle wheel work is
A. 500 kJ B. 423 kJ C. 400 kJ D. 363 Kj

Solution:
𝑚𝑅 ∆𝑇
𝑊=
1−𝐾
5(0.2867)(100)
𝑊= 1−1.4

𝑾 = 𝟑𝟓𝟖 𝑲𝑱
37. Prefix 105 is
A. Pico B. atto C. peta D. Fernto

198
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
38. If the density of the gas is 0.003 slugs per cubic foot, what is the specific weight of
the gas?
A. 9.04 N/cu. M B. 15.2 N/cu .m
C. 76.3 N/cu. M D. 96.2 N/ cu. M

Solution:
14.59 1 𝑵
= (0.008) ( )( )2 = 𝟏𝟓. 𝟐 𝟑
1 0.304 𝒎
39. Which of the following refer to the diffusion of a solvent into a stronger solution in an
attempt to equalize the two concentrations?
A. Purification B. electrolysis
C. osmosis D. hydrolysis

40. If a 1/3 horsepower pump runs for 20 minutes, what is the energy used?
A. 0.06 ergs B. 0.25 KW
C. 0.30 MJ D. 0.11 KW-hr

Solution:
1
(3 𝐻𝑝)(746W) = 249W
249KW (1200) = 0.3MJ

41. What is the pressure of 4.87 grams’ hydrogen from that occupy 6.6 liters at 12 deg
C?
A. 8.65 atm B. 9.64 atm C. 8.31 atm D. 9.84 atm

Solution:
𝑚𝑅𝑇
𝑃= 𝑉
8.3144
(4.87 𝑥10−3 )( )(12+273)
2
𝑃= 6.6
1000

1 𝑎𝑡𝑚
𝑃 = 842. 01 𝐾𝑃𝑎 (101.325 𝐾𝑃𝑎)

𝑷 = 𝟖. 𝟑𝟏 𝒂𝒕𝒎
42. What is the frequency of oscillation of a body if its mass m is 0.015 kg and k is 0.5
N/m?
A. 0.51 Hz B. 0.66 Hz
C. 0.78 Hz D 0.92 Hz

199
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

0.5
𝑊 = √ = 5.77𝑟𝑎𝑑/𝑠
0.015
5.77
∴𝐹 = = 𝟎. 𝟗𝟏𝟖
2𝑝𝑖
43. A measure of how it emits radiant energy in comparison with a blackbody at the
same temperature.
A. Absorptivity B. reflectivity
C. emissivity D. conductivity

44. A solid wooden cube 30.0 cm on each edge can be totally submerged in water if it is
pushed downward with a force of 54 N. What is the density of the wood
A.900 kg/cu. M B. 800 kg/cu.
C. 700 kg/cu. M D. 600 kg/cu.

Solution:
𝑊 + 𝑇 − 𝐹𝑏 = 0
𝑊 + 𝑇 = 𝐹𝑏
𝑤 = 𝑚𝑔 ; 𝐹𝑏 = 𝛾𝑉𝑑
𝑚(9,81) + 54 = 9.81𝑥103 (3)3
𝑚 = 21.495 𝑘𝑔
𝜌 = 𝑚⁄𝑣
21.495 𝑘𝑔 𝒌𝒈 𝒌𝒈
𝝆= ⁄(0.3)3 = 𝟕𝟗𝟔. 𝟏𝟑 ≈ 𝟖𝟎𝟎 𝒎𝟑
𝒎𝟑

45. Find the magnitude of the resultant of two 10-lb forces applied at the same point
when the angle between them is 130 degrees.
A. 7.8 lbs. B. 18.1 lbs. C. 19.5 lbs. D. 8.5lbs

Solution:
10 < 130 + 10 < 0 = 3.57 + 𝑗7.66 = 𝟖. 𝟒𝟓 < 𝟔𝟓
46. The shaft of a motor turns at a constant 3000 rpm, in 40s it turns through
A. 2,000 rad B. 6,283 rad
C. 12,000 rad D. 12,566 rad

200
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
𝑅𝐴𝐷 = 𝑅𝑃𝑆 (𝑡𝑖𝑚𝑒)(2𝜋)
3000
𝑅𝐴𝐷 = ( ) (40)(2𝜋)
60

𝑹𝑨𝑫 = 𝟏𝟐𝟓𝟔𝟔 𝒓𝒂𝒅


47. A lbm at 200 deg F iron (C =0.1 BTU /lbm – def F) are dropped into a gallon of 40
deg F of water. What is the final temperature of the mixture?
A. 55.21 deg F B. 48.12 deg F
C. 38.92 deg F D. 43.74 deg F

Solution:
−𝑄𝐿𝑂𝑆𝑇 = 𝑄𝐺𝐴𝐼𝑁𝐸𝐷
(2)(0.1)(𝑡2 − 200) = (3.785)(2.205)(40 − 𝑡2 )
𝒕𝟐 = 𝟒𝟑. 𝟕𝟒℃
48. A rubber band has an un stretched length of 180mm. if it is stretched around a pole
having a diameter of 60 mm, determine the average normal strain in the band.
A. 0.0427 B. 0.0236 C. 0.0253 D. 0.47

Solution:
Δ𝑙
𝜀= L

Δ𝑙 = 𝐿𝑠𝑡𝑟𝑒𝑡𝑐ℎ − 𝐿𝑢𝑛𝑠𝑡𝑟𝑒𝑡𝑐ℎ
Δ𝑙 = 𝜋𝐷 − 𝐿
Δ𝑙 = 𝜋(60) − 180 = 8.5 𝑚𝑚
8.5 mm
𝜺= = 𝟎. 𝟒𝟕
180 mm
49. In a certain process 500 cal. Of heat are supplied to a system and at the same time
100 joules of work are done. What is the increases in the internal energy of the
system?
A. 546.8 cal B. 476.1 cal
C. 427.6 cal D. 523.9 cal

Solution:
∆𝑈 = 𝑄 + 𝑊
100
∆𝑈 = 500 + 4.186
201
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
∆𝑼 = 𝟓𝟐𝟑. 𝟗 𝒄𝒂𝒍
50. Convert 10110111 (base 2) to the base 10 equivalent
A.42.25 B. 45.75 C. 48.68 D. 52.35

51. An employee obtained a load of P10,000 at a rate of 6% compounded annually in


order to build a house. How much must he pay monthly to amortize the loan within a
period of 10 years?
A. P120.42 B. P110.22
C. P105.75 D. P115.64

Solution:
𝑃
=𝐴
1 − (1 + 𝑖)−𝑛
[ ]
𝑖
𝑃 10000
𝐴 = 1−(1+𝑖)−𝑛 = 1−(1+0.06)−(12)(10) =
[ ] 12
𝑖 [ 0.06 ]
12
𝑨 = ₱ 110.02 = 𝐁.

52. Convert the base 10 integer 432 to its base 16 equivalent.


A. 1B0 B. 1FC C. 2A3 D. 1420

Solution:
432 ÷ 16 = 27 𝑟 0
27 ÷ 16 = 1 𝑟 𝐵
1 ÷ 16 = 0 𝑟 1
43210 1B016

53. Convert 110 deg. F to deg. C.


A. 43.33 B. 42.22 C. 40.23 D. 46.32

Solution:
5
𝐶 = (110 − 32)
9
∴ 𝑪 = 𝟒𝟑. 𝟑𝟑

54. At the end of each of the next ten years, a payment of $200 is due. At an interest
rate of 6%, what is the present worth of the payments?
A. $27 B. $200 C. $1472 D.$2000

202
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
1 − (1 + 0.06)−10
𝑃 = 200( ) ; 𝑷 = 𝟏𝟒𝟕𝟐
0.06
55. What is the most nearly the resulting pressure when 400 g of air at 103.6 kPa ad 93
deg. C is heated at constant volume to 427 deg. C?
A. 918 kPa B. 198 kPa
C. 819 kPa D. 189 kPa
Solution:
(103600)(700)
𝑃2 = 𝑷𝟐 = 𝟏𝟗𝟖. 𝟏𝟒𝟐𝟏 𝒌𝑷𝒂
(386)

56. What is the speed of light through a water whose index of refraction is 1.33?
A. 1.8 x 10^8 m/s B. 2.26 x 10^8 m/s
C. 2.51 x 10^8 m/s D. 2.79 x 10^8 m/s

Solution:
300000000
𝑣 =
1.33
∴ 𝒗 = 𝟐. 𝟐𝟔 𝒙 𝟏𝟎𝟖 𝒎/𝒔

57. A square steel bar 50mm on a side and 1m long is subject to an axial tensile force of
250 Kn. Determine the decrease in the lateral dimension due to this load. Consider
E = 200 GPa and µ = 0.3.
A. 0.0057 mm B. 0.0075 mm
C. 0.0065 mm D.0.0067 mm

Solution:

(250𝑥103 )(1000)
𝛿=( )(0.3); 𝜹 = 𝟎. 𝟎𝟎𝟕𝟓
50 9
(1000)(200𝑥10 )

58. Determine the maximum shearing stress in a 4-in-diameter solid shaft carrying a
torque of 228, 000 lb-in.
A. 18,000 lb/sq. in B. 17,000 lb/sq. in C. 16,000 lb/sq. in D.19,000 lb/sq. in
Solution:

203
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS

16(228,000)
𝑆𝑠 = ; 𝑺𝒔 = 𝟏𝟖, 𝟏𝟒𝟑. 𝟔𝟔𝟑𝟓𝟏
𝜋(4)3

59. A square steel bar is 50 mm on a side and 250 mm long. It is loaded by an axial
tensile force of 200 Kn. If E = 200 GPa and µ = 0.3, determine the change of volume
per unit volume.
A. 0.0016 B. 0.000016 C. 0.00016 D. 0.016

Solution:

∆𝑉 200000
= (1 − 2 (0.3))
𝑉 (0.0025)(200𝑥109 )
𝚫𝑽
∴ = 𝟎. 𝟎𝟎𝟎𝟏𝟔
𝐕
\
60. Calculate the mass of nitrogen at 150 K and 2 MPa contained to 0.2 cu. M.
A. 10.2 kg B. 8.98 kg C. 6.23 kg D. 2.13 kg

Solution:
(2000000)(0.2 𝑚3 )
m=
(
8.314
)(150)
;
28

m = 𝟏𝟎. 𝟐 𝒌𝒈 = A.

61. A solid circular shaft is required to transmit 200 kW while turning at 1.5 rev/s. The
allowable shearing stress is 42 MPa. Find the required shaft diameter.
A. 148 mm B. 138 mm C. 126 mm D. 156 mm

Solution:

𝑟𝑒𝑣 𝑠
2𝜋𝑇((1.5 𝑠 ) (60 𝑚))
200 = ; 𝑇 = 21220.65908
60
16(21220.65908)
𝐷3 = ; 𝑫 = 𝟏𝟑𝟖
𝜋(42𝑥106 )
62. What is the temperature rating of a TW insulated conductor?
A.60 deg. C B. 75 deg. C
C. 90 deg. C D. 100 deg. C

63. Find the maximum shearing stress, in MPa, of a simply supported 6 m long beam
with a 5 x 5 cm cross section if it has 2000 N load at the midpoint.
204
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A.0.6 B. 0.9 C. 1.2 D. 1.6

Solution:

1000
𝑆𝑠 = ; 𝑺𝒔 = 𝟎. 𝟔
(50)(50)

64. A graphical device used to convert a truth table to its corresponding logic circuit in a
simple, orderly process.
A. State Table B. State Diagram
C. Karnaugh Map D. Truth Table

65. The members of the board shall hold the office for a term of ___ years from the date
of appointment or until their successors shall have been appointed and qualified.
A. 4 B. 6 C. 3 D. 5

66. Air having an initial pressure Pi = 14 psia, temperature Ti = 80 deg. F, and volume Vi
= 29 cu. Ft. is compressed isentropically in a nonflow process to a final pressure Pf
= 120 psia. The final temperature in deg. F, is nearest to
A. 815 B. 540 C. 370 D.200

Solution:

120 1.4−1
T2=(80+460)( 14 ) 1.4 − 460; T2=53.65 ≈540

67. Calculate the increase in volume per unit volume of a thin-walled steel circular
cylinder closed at both ends and subjected to a uniform internal pressure of 0.5
MPa. The wall thickness is 1.5 mm, the radius 350 mm and µ = 1/3. Consider E =
200 GPa.
A. 10^-4 B. 10^-5 C. 10^-6 D. 10^-3

Solution:

Δ𝑉 𝑃
= 𝐴𝐸 (1 − 2𝜇)
V

Δ𝑉 600𝑥106 1
= (200)(9) (1 − 2 (3))
V
𝚫𝑽
= 𝟏𝟎−𝟑
𝐕

205
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
68. A parachutist relies on air resistance (mainly on her parachute) to decrease her
downward velocity. If she and her parachute have a mass of 55.0 kg, and air
resistance exerts a force of 620 N upward, what is her acceleration?
A. 3.68 m/s^2 B. 0.79 m/s^2
C. 2.58 m/s^2 D. 1.47 m/s^2

Solution:

𝐹 = 𝑚𝑎
620 = (55)𝑎
𝑎 = 11.27

𝑎 𝑇 = 𝑎 − 𝑎𝑔
𝑎 𝑇 = 11.27 − 9.81
𝒎
𝒂𝑻 = 𝟏. 𝟒𝟔 𝟐
𝒔

69. Define WESM?


A. Wholesale Electrical Spot Market
B. Wholesale Electrical Supply Market
C. Wholesale Electricity Spot Market
D. Wholesale Electricity Supply Market

70. The section modulus in cu. m., about the central axis of a 10 cm by 25 cm beam on
edge is closest to
A. 721 B. 984 C. 1080 D. 1042

Solution:
(25)(103 )
= ; = 1041.66
24
71. All the powers of the TRANSCO shall be vested in and exercised by a Board of
Directors. Who will be the ex officio Chairman of the Board?
A. Sec. of the Dept. of Energy (DOE)
B. Sec. of the Dept. of Finance (DOF)
C. Secretary of DENR
D. President of TRANSCO

72. At least how many receptacle outlets shall be installed in the bathroom?
A. One B. Two C. Three D. Four

206
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
73. Two blocks if masses m1 = 2 kg and m2 = 4 kg on ta frictionless horizontal surface
are in contact with each other. A force F = 6 N is applied to block (mass m1). How
large a force does m1 exert on m2.?
A. 2N B. 3N C. 4N D.6N

Solution:
𝐹 = 𝑚𝑎
𝑚
6 = (2 + 4)𝑎 ; 𝑎 = 1 𝑠
𝐹2 = 𝑚2 𝑎
𝐹2 = 4(1)
𝑭𝟐 = 𝟒 𝑵
74. A man loans P187,400 from the bank with interest at 5% compounded annually. He
agrees to pay his obligations by paying 8 equal annual payments, the first being due
at the end of 10 years. Find the annual payments.
A. P43,600.10 B. P43,489.47
C. P44,263.91 D. P44,980.56

Solution:

(1+𝑖)𝑛 −1
𝑃=𝐴 [ (1+𝑖)𝑛 𝑖
] [1 + 𝑖]𝑛+1
(1+0.05)8 −1
187, 400 = 𝐴 [(1+0.05)8 (0.05)] [1 + (0.05)]−10+1

𝑨 = 𝑷𝟒𝟒, 𝟗𝟖𝟎. 𝟓𝟔
75. When an object exerts force on another object, the second object exerts on the first
a force of the same magnitude but in opposite direction. This statement is in
accordance to
A. Newton’s First Law of Motions
B. Newton’s First Second of Motions
C. Newton’s Third Law of Motions
D. All of these
76. A barrel weighing 250 lb is suspended by a rope 30 ft long. What horizontal force is
a necessary to hold the barrel sideways 5 hr from the vertical?
A. 92.46 lb B. 94.62 lb C. 24.62 D. 42.26 lb
Solution:

77. What is the moment of inertia with respect to the axis of rotation of a thin circular
disk of a turntable used by a DJ if the mass of the disk is 70 grams and its radius is
1.5 in?
A. 4.73x10^-6 kg-m^2 C.10.16x10^-5 kg-m^2
207
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
B. 9.45x10^-5 kg-m^2 D. 5.06x10^-5 kg-m^2

Solution:
1𝑘𝑔 1𝑓𝑡 1𝑚 2
= (70𝑔𝑥 )(1.15𝑖𝑛𝑥 𝑥 )
1000𝑔 12𝑖𝑛 3.28𝑓𝑡
1.0166𝑥10−4
= = 𝟓. 𝟎𝟖𝟑𝒙𝟏𝟎−𝟓
2

78. If Php 100,000 is invested at 12% interest, compounded monthly, the first year
interest is nearest to
A. Php 12,000 B. Php 12,350
C. Php 12,700 D. Php 12,850

Solution:

0.12 12
𝐹 = 100,000(1 + ) ; 𝐹 = 112682.508
12
𝐼 = 𝐹 − 𝑃 = 112,682.503 – 100,000 = 𝟏𝟐, 𝟔𝟖𝟐. 𝟓𝟎𝟑

79. Determine the modulus of residence (kJ/cu.m) for malleable cast from iron. E = 165
GPa, normal stress = 230 MPa.
A. 160.7 B. 170.6 C. 280.5 D. 250.8

80. A particle traveling on a curve path has a velocity of 36m/s and a normal
acceleration of 18m/s^2 at a certain point. The radius of curvature of the path at the
point is.
A. 56 m B. 59 m C.63 m D.72 m

Solution:

𝐶𝐹 = 36(18) = 648
36(36)2
648 = ; 𝑹 = 𝟕𝟐
𝑅
81. In 1906 an original painting of Picasso has a market price of $ 600.00 and in1995 its
price has increased to $ 29,000,000.00. What is the rate of interest of the painting?
A. 10.9% B. 12.9%
C. 9.9% D.11.9%
Solution:

208
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
29,000,000
600 = 1995−1906 ; 𝐼 = 𝟏𝟐. 𝟗%
(1+𝑖)
82. The Moody diagram is used in fluid mechanics to obtain
A. The drag coefficient C.the friction factor
B. The Stroudal number D.the pressure coefficient

83. A surveyor’s steel tape 30 m long has a cross-section of 6mm by 1mm. Determine
the elongation when the entire tape is stretched and held taut by a force of 50 N.
The modulus of elasticity is 200 GFs.
A. 2.50 mm B. 0.75 mm C. 1.75 mm D. 1.25 mm

Solution:
50(30)
𝛿 = ; 𝛿 = 𝟏. 𝟐𝟓𝒎𝒎
6(200)
84. A height of 5 ft 8 in is equivalent to
A. 173 cm B. 177 cm C. 207 cm D. 223 cm
Solution:
12𝑖𝑛 2.54𝑐𝑚
5.66𝑓𝑡 𝑥 ( )( ) = 𝟏𝟕𝟐. 𝟕 𝒄𝒎
1𝑓𝑡 1𝑖𝑛
85. A wave has a frequency of 2.9 Hz and a velocity of 3.0 m/s. The distance covered by
the wave in 5.0 s is
A. 30 m B. 15 m C. 7.5 m D. 6.0 m

Solution:

𝑑 = (3.0𝑚/𝑠)(5.0𝑠)
∴ 𝒅 = 𝟏𝟓𝒎
86. A car that travels at 40 kph for 2.0 hours at 50 kph for 1.0 hour, and at 20 kph for
0.05 hour, has an average speed of
A. 31 kph B. 40 kph C. 45 kph D. 55 kph
Solution:
40 + 50 + 20
𝐴𝑠 = ; 𝑨𝒔 = 𝟑𝟔. 𝟔𝟕 ≈ 𝟒𝟎𝒌𝒑𝒉
3
87. The coils of D. C. motor starter are wound with wire of
A. Copper B. manganin C. kanthal D. Nicrome

88. How much external work is done by an ideal gas expanding from a volume of 3.0
liters to a volume of 30.0 liters against a constant pressure of 2.0 atrn?
209
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A. -10.5 kJ B. +10.5 kJ C. -5.5 kJ D. +5.5 kJ
Solution:
30 − 3
𝑃𝑑𝑣 = 101.325(2)( )𝑷𝒅𝒗 = 𝟓. 𝟒𝟕𝒌𝑱
1000
89. Gasoline has a specific gravity of 0.68. One liter of gasoline weighs
A. 0.68 N B. 1.4 N C. 6.7 N D.8.6N

Solution:
𝑆𝑝𝑒𝑐𝑖𝑓𝑖𝑐 𝐺𝑟𝑎𝑣𝑖𝑡𝑦 = (𝑆𝐺 𝑒𝑎𝑟𝑡ℎ 𝑥 𝑆𝐺 𝑔𝑎𝑠𝑜𝑙𝑖𝑛𝑒)
𝑆𝑔 = 9.81(0.68)
∴ 𝑺𝒈 = 𝟔. 𝟔𝟕𝑵

90. The chemical shorthand for molybednum is


A. Mo B. Mb C. Md D. Mn

91. Which two metals combine to give galvanized metal?


A. Lead and tin B. zinc and iron
C. tin and iron D. zinc and tin

92. A mass of oxygen occupies 0.0200 cu.m. at atmospheric pressure, 101 kPa and 5.0
deg C. Determine its volume if its pressure n increased to 108 kPa while its
temperature is change to 30.0 deg C.
A. 0.023 cu.m. C.0.0204cu.m
B. 0.23 cu.m. . D. 0.204 cu.m.
Solution:

(101(0.0200))/(5 + 273) = (108(𝑉_(2)))/(30 + 273) ; 𝑽𝟐 = 𝟎. 𝟎𝟐𝟎𝟒


93. At 10% per year interest rate, $ 500 now is equivalent to how much three years
hence?
A. $ 556.50 B. $ 628.50 C. $ 685.50 D. $ 682.50

Solution:

𝐹 = 500(1 + 0.10)3
∴ 𝑭 = 𝟔𝟖𝟓. 𝟓
94. The pressure of a gas is directly proportional to the Kelvin temperature in
A. Boyle’s law B. Gay-Lussac’s law
C. Boyd’s law D. Charles’ Law

210
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
95. A projectile with a mass 0.01 kg has a muzzle velocity of 1,000 m/s when fired from
a riffle weighing 5 kg. The recoil velocity of the rifle is
A. 0.1 m/s C.5m/s
B. 2 m/s D. 50 m/s
Solution:

𝑚1 𝑉1 = 𝑚2 𝑉2
(0.01)(1000) = (5)(𝑉2 )
𝑽𝟐 = 𝟐 𝒎⁄ 𝟐
𝒔
96. A spaceship orbits the Moon at a height of 20,000 m. assuming it to be subject only
to the gravitational pull of the Moon, find the time it takes for one orbit. For the Moon,
m = 7.34 x 10^22 kg and r = 1.738 x 10^6 m.
A. 95 min C.210min
B. 85 min D. 110 min
Solution:

97. An iron plate 2 cm thick has a cross of 5,000 sq. cm. One face is at 150 deg. C and
the other is at 140 deg. C. How much heat passes through the plate each second?
For iron, kt = 80 W/m-K.
A. 20 kJ/s B. 16 kJ/s C. 27 kJ/s D. 36 kJ/s

Solution:

𝐾𝐴∆𝑇
𝑄= 𝑋
5000
80[ ][150−40]
1002
𝑄= 2
( )
100

𝑲𝑱
𝑸 = 𝟐𝟎
𝒔
98. The only force acting on a 5.0 kg object has components F = 20 N and Ft = 30 N.
Find the magnitude of the acceleration of the object.
A. 4.0 m/s^2 B.6.0 m/s^2
C. 7.2 m/s^2 D. 10.5 m/s^2

Solution:

𝐹 = 𝑚𝑎
𝐹 = |20 + 30∠90|
211
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
MARCH 2013
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝐹 = 36.06
36.06 = (5)(𝑎)
𝒎
𝒂 = 𝟕. 𝟐 𝟐
𝒔
99. If the pressure in a tank of oil (spr. gr. = 0.80) is 400 kPa, what is the equivalent
head in meters of water.
A. 50. 97 B. 40.77 C. 59.70 D. 47.70

Solution:
400
= ; = 𝟒𝟎. 𝟕𝟕
9.81
100. A piston allows air to expand from 6 MPs to 200 kPa. The initial volume and
temperature are 500 cu.m. and 800 deg C. If the temperature is held constant,
calculate the heat transfer.
A. 10.20 kJ B. 12. 60 kJ C. 9.62 kJ D. 8.46 Kj
Solution:
200
𝑄 = 6(300)𝑙𝑛( )
6
∴ 𝑸 = 𝟏𝟎. 𝟓𝟏𝟗𝟔𝒌𝑱 ≈ 𝟏𝟎. 𝟐𝟎𝒌𝑱

212
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ESAS PRE-BOARD EXAM AUGUST 2012

1. In how many years will the investment to double in value at 5% simple interest rate?
A. 2 B. 4 C. 20 D. 40

Solution:
2P=P(1+0.05n)
P=P; F=2P n=20 years
F=P(1+in)

2. A machine cost $75,000 after 1 year. If the rate of interest is 18% compounded
annually, what is its price now?
A. $63,955.23 C. $65,933.23
B. $63,559.32 D. $65,339.32

Solution:
F=75,000 i=0.18 or 18% n=1(annually)
-n -1
P=F(1+i) = 75,000(1+0.18) =$ 63,669.32

3. A soccer player kicks the rock horizontally off a cliff 40m high. Then hears the splash
of water 3s after. Find the initial velocity of the rock. Assume the speed of sound =
343m/s
A. 17.89 m/s B. 9.91 m/s C. 9.30 m/s D. 10.56 m/s

Solution:

trock+tsound = 3sec.
Y=40m
For trock:
1
y= gt2 x=√48.022 -402 =26.56m
2
2y 2(40) x=Vo cosθtr
tr =√ =√ = 2.86 sec 26.56
g 9.81 Vo = = 9.29 m/s
2.86
ts =3-2.86=0.144 sec
dsound =(343)(0.14)=48.02 m

A man on the moon pushes a 10-kg box using a 100 N-force. What is the acceleration
of the box? Assume amoon= 1.67 m/s^2. Ignore

A. 15 m/s^2 B. 20 m/s^2 C. 40 m/s^2 D. 10 m/s^⁶

Solution:
213
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
𝑚
F = 100N m =10kg amoon= 1.67 𝑠2
F=ma
F 100 𝒎
a= = = 10 𝟐
m 10 𝒔

5. The external pressure applied to a confined fluid increases the pressure of every
point in the fluid by an amount equal to the external pressure. This is known as
A. Pascal's principle C. Torricelli's Theorem
B. Archimedes principle D. Bernoulli's Theorem

Explanation:

Pascal’s principle, also called Pascal’s law, in fluid (gas or liquid)


mechanics, statement that, in a fluid at rest in a closed container,
a pressure change in one part is transmitted without loss to every portion of the
fluid and to the walls of the container. The principle was first enunciated by the
French scientist Blaise Pascal.
Archimedes' principle states that the upward buoyant force that is exerted
on a body immersed in a fluid, whether fully or partially submerged, is equal to
the weight of the fluid that the body displaces and acts in the upward direction at
the center of mass of the displaced fluid.
Torricelli's law, also known as Torricelli's theorem, is a theorem in fluid
dynamics relating the speed of fluid flowing out of an orifice to the height of fluid
above the opening.
Bernoulli, the theorem states, in effect, that the total mechanical
energy of the flowing fluid, comprising the energy associated with fluid pressure,
the gravitational potential energy of elevation, and the kinetic energy of fluid
motion, remains constant.

6. A year ago, Dennis invests $900 then a year after he gets an annual return of
$1100. What is the interest rate?
A. 11.11% B. 22.22% C. 10.55% D. 12.22%

Solution:

P=$900 Annual return = $1,100


F=P
900(1+i) = 1,100(1+i)-1
1

i = 0.1055×100
i = 10.55%
7. Maximum distances between busway supports.
A. 1000 mm B. 1500 mm C. 1800 mm D. 2000 mm

214
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
8. Calculate the molarity of a solution after 1.70 L of 2.06 M solution is diluted to 2.50 L.
A. 1.40 M B. 2.08 M C. 0.883 M D. 3.42 M

Solution:
𝑚𝑜𝑙𝑒𝑠 𝑜𝑓 𝑠𝑜𝑙𝑢𝑡𝑒
Molarity = 𝑙𝑖𝑡𝑒𝑟𝑠 𝑜𝑓 𝑠𝑜𝑙𝑢𝑡𝑖𝑜𝑛
x
2.06= ; x= 3.502 L/mol
1.70
3.502
M= = 1.4M
2.50
9. Which of the following holds true for any given material?
A. 1/3 ≥ G/E ≥ 1/2 C. 1/3> G/E ≥ 1/2
B. 1/2 > G/E > 1/3 D. 1/2 ≥ G/E ≥ 1/3

10. A reservoir dam holds an 8.00-km^2 lake behind it. Just behind the dam, the lake is
12.0m deep. What is the water pressure at a point 3.0m down the from the lake’s
surface?
A. 27 B. 29 C. 25 D. 24

Solution:

P = γh
P = ρgh =(1)(9.81)(3) = 29.4 ≈ 29kPa

11. What is the tensile load if a ½” x 4” x 12’ steel the rod experiences an 80 deg F
temperature decrease from the no stress temperature?
A. 9,850 lb. B. 15,600 lb. C. 31,200 lb. D. 62,400 lb.

Solution:

δ=αL(∆t)
PL
δ=
AE
Equate the two formulas
PL
αL(∆t)=
AE
(∆t)αAE= P
6.5×10-6 lb
∆t = (80°F); α= ( ) ; 𝐴 = (.5in)(4in); 𝐸 = (30×106 2 )
°F in

6.5×10-6 lb
(80°F) ( ) (.5in)(4in) (30×106 2 ) = P
°F in
215
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
P=31200 lb

12. What charge has the elements belong to the group 2?


A. 2 B. 1 C. -2 D. -1

Explanation:
Group I (alkali metals) carry a +1 charge,
Group II (alkaline earths) carry a +2,
Group VII (halogens) carry -1, and
Group VIII (noble gases) carry a 0 charge. Metal ions
may have other charges or oxidation states

13. What does UPS mean?


A. Uninterrupting Portable Supply
B. Uninterruptable Power Supply
C. Uninterrupting Power Supply
D. Uninterruptable Portable Supply

14. An electric motor lifts a 10-kg mass 100 m in 10s. The power developed by the
motor is
A. 9.8 W B. 98 W C. 980 W D. 9,800 W

Solution:

m=10kg

w = mg = (10)( 9.8 ) = 98N


𝑤𝑜𝑟𝑘
power = 𝑡𝑖𝑚𝑒

(10)(9.81)(100)
Power = = 980W
10
15. Which device could be used to determine whether a substance is radioactive?
A. a Van de Graaff generator C. a cyclotron
B. a Geiger counter D. a linear accelerator

Explanation:

A Geiger counter is an instrument used for detecting and measuring


ionizing radiation. Also known as a Geiger–Mueller counter, it is widely used in
applications such as radiation dosimetry, radiological protection, experimental
physics, and the nuclear industry.

216
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
A linear particle accelerator is a type of particle accelerator that
accelerates charged subatomic particles or ions to a high speed by subjecting
them to a series of oscillating electric potentials along a linear beamline.
A Cyclotron is an apparatus in which charged atomic and subatomic
particles are accelerated by an alternating electric field while following an
outward spiral or circular path in a magnetic field.
A Van de Graaff generator is an electrostatic generator which uses a
moving belt to accumulate electric charge on a hollow metal globe on the top of
an insulated column, creating very high electric potentials.

16. For a 20-amp receptacle connected to 20-amp branch circuit supplying two or more
outlets, the total cord-and-plug may not exceed which of the following sizes:
A. 20 amps C. 30 amps
B. 15 amps D. none of these

17. What is the pH value of a solution with acetic acid concentration of 3.0 x 10^-6 M?
A. 12.72 B. 14.28 C. 5.523 D. 3.472

Solution:

pH = - log(M)
pH = - log(3×10-6 ) = 5.523

18. What is the mass number of an atom with 9 protons, 11 neutrons, and 9 electrons?
A. 9 B. 18 C. 20 D. 29

Solution:

Mass number = number of electron + number of neutrons


mass number = 9 + 11 = 20

19. Which is not a standard overcurrent protection device rating?


A. 50 B. 1500 C. 225 D. 110

20. It is responsible for the procurement and administration of funds with the view of
achieving the objectives of business.
A. Capital B. Budget C. Finance D. Funds

21. An impulse of 30 N∙s is applied to a 5-kg mass. If the mass had a speed of 100
m/sec before the impulse, its speed after the impulse could be
A. 250 m/s B. 106 m/s C. 6.00 m/s D. 0 m/s
217
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
P=30 N∙s m=5kg Vo=100 m/sec
P= mv = m(Vf – Vo)
30 = (5)(Vf - 100)
Vf = 106 m/s
22. The sun is directly overhead of the eagle. The eagle dives at 50 m/s at an angle of
30 degrees below the horizontal. What is the velocity of the shadow?
A. 43.3 m/s B. 34.3 m/s C. 25.o m/s D. 52.0 m/s

Solution:
𝑚
Vo = 50 θ=30°
𝑠
Vox = Vo cosθ
Vox = (50) cos(30)
𝒎
Vox = 43.3
𝒔
23. A device used to measure atmospheric pressure is called
A. Manometer C. Pycnometer
B. Barometer D. Hydrometer

Explanation:

A barometer is a scientific instrument used to measure air pressure.


Pressure tendency can forecast short term changes in the weather.
A Manometer is a device to measure pressures.
A gas pycnometer is a laboratory device used for measuring the density—
or, more accurately, the volume—of solids, be they regularly shaped, porous or
non-porous, monolithic, powdered, granular or in some way comminuted,
employing some method of gas displacement and the volume: pressure
relationship known as Boyle's Law.
A hydrometer is an instrument used for measuring the relative density of
liquids based on the concept of buoyancy
24. A bar of uniform cross section is subject to uniaxial tension and develops a strain in
the direction of the force of 1/800. Calculate the change of volume per unit volume.
Assume μ = 1/3
A. 1/2400 (inc) C. 1/1200 (inc)
B. 1/2400 (dec) D.1/1200 (dec)

Solution:

∆V P 1
= =
V AE 800
∆V 1 1
= [1-2 ( )]
V 800 3
218
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
∆V 1
= (increased)
V 2400

25. When a submarine dives a depth of 120 m, to how large a total pressure is its
exterior surface subjected? The density of seawater is 1.03 g/cc.
A. 1.41 MPa B. 1.21 MPa C. 1.31 MPa D. 1.11 MPa

Solution:

h=120m density of seawater = 1.03 g/cc.


1.03g 1 kg (100cm)3 kg
= × × = 1,030
cm3 1000g (1m)3 m3
where:P=ρgh
PT =Patm +P
PT =101.325×103 Pa+(1030)(9.81)(120)
PT =1.31MPa

26. Air enters a turbine at 5 kg/s at a velocity of 20 m/s at a temperature of 200 K and
exits at a velocity of 500 m/s. What is the power (kW) due to change in kinetic
energy?
A. 624 B. 426 C. 836 D. 368

Solution:

V0=500m/s Vf=20m/s m= 5kg/s t=200K


W = ∆KE
1 1
W = mv2 = m(vf 2 -vo 2 )
2 2
1
W = (5)(5002 -202 )
2
W = 624,000W = 624Kw

27. What is RES stands for in EPIRA?


A. Retail Energy Supply C. Retail Electricity Supply
B. Retail Energy Suppliers D. Retail Electricity Suppliers
28. A 80-kg rectangular box open at the top, has base dimensions 1.0 m by 0.8 m and
depth 0.50 m. How deep will it sink in fresh water?
A. 0.025 m B.0.050m C. 0.075m D. 0.095 m

Solution:

219
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
V= (1)(0.8)(0.5) = 0.4m3 ρgh = ρgh
m 60 kg 150kg (150)(9.81)(0.5) = (1000)(9.81)(h)
ρ= = =
v 0.4m3 m3 h= 0.075m
P = Pwater

29. Find the angle of banking for a highway curve of 90 m radius designed to
accommodate cars traveling at 160kph, if the coefficient of friction between the tires
and the road is 0.60
A. 34.9 deg B. 44.6 deg C. 20.3 deg D. 47.2 deg

Solution:

r=90m V=160kph friction= 0.60

v2
∅= tan(θ+∅) =
-1
gr
tan (0.60) = 30.96° 44.442
km 1000 m 1 hr m tan(θ+30.96) =
v = 160 × × = 44.44 (9.81)(90)
hr 1 km 3600 s s
θ = 34.95°

30. Which is not a unit of power?


A. joules/second C. watts
B. newton-seconds D. calories/second
31. The density of nitrogen is 1.25 kg/cu. m at ST.P. Determine the density of nitrogen at
42 deg C and 730 mm of mercury
A. 1.09 kg/cu. m. C. 1.04 kg/cu. m.
B. 1.90 kg/cu. m. D. 1.40 kg/cu. m.

Solution:

PV = mRT P = ρRT ρRT = ρRT + P

ρ=1.25 kg/cu. m R=296.86 t=42+273=315 P= 730 mm of mercury


730mmHg
(1.25)(296.86)(273) = [P(296.86)(42+273) + 101.325 + ( ) (101.325)]
760mmHg
P = |-1.041kg/m3 | = 1.041kg/m3

32. A turbine started from rest to 180 rpm in 6 min at a constant acceleration. Find the
number of revolutions that it makes within the elapse time
A. 550 B. 540 C. 630 D. 500

Solution:

220
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS

ωf -ωo 180 30 rev


∝= = =
t 60 min2
1
θ = gt2
2
1 rev
θ = (30 2 ) (6min)2 = 540rev
2 m
33. 200 grams of aluminum block at 400 deg C is dropped into a 1 kg aluminum
calorimeter containing 100 grams of water at 5 deg C. What is the final temperature
of the mixture, in deg C? Cal= 0.22 kcal/kg-deg C.
A. 25.7 B. 52.7 C. 64.8 D. 46.8

Solution:

m1=200 grams of aluminum block @ t=400 degC

m2=1 kg aluminum calorimeter Cal= 0.22 kcal/kg-deg C.

m3=100 grams of water @ t= 5 deg C


Qgain = -Qloss
(0.2)(0.22)(T-400) = -[(0.1)(1)(T-5)=(1)(0.22)(T-5)]
T = 52.74℃

34. An 8 unit long pendulum subtends an angle of 34 degrees. What is the height
difference from its stationary position?
A. 1.37 B. 1.73 C. 1.26 D. 1.62

Solution:

l-h
Cosθ=
l
8-h
cos(34) = ( )
8
h=1.367 ≈ 1.37 unit

35. Which wave requires a medium for transmission?


A. light B. infrared C. radio D. sound

36. Calculate the mass of the oxygen that reacts with 1.24 g of methane (natural gas) to
form 3.41 g of carbon dioxide and 2.79 g of water.
A. 4.96 g B. 4.65 g C. 7.44 g D. 1.86 g

Solution:

221
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS

Moxygen = (Mcarbon +MH2 O ) – (Mmethane )


Moxygen = (34.1+2.79) - (1.24)
Moxygen = 4.96g

37. A substance formed by the union of two or more chemical elements in a definite
proportion that can be only be separated by chemical means
A. mixture C. ion
B. molecules D. compound

38. An object 6 cm high is placed 12 cm away from a concave mirror whose focal length
is 36 cm. What is the height of the image?
A. 3cm B. 4cm C. 9cm D. 8cm

Solution:

1 1 1
+ =
p q f
1 1 1
- - =
f p q
1 1 -1
(- - ) =q
36 12
q = - 9cm or q = 9cm

39. Calculate the molality of solution containing 0.500 mol of solute in 250 g of solvent.
A. 1.50 m B.2.00 m C. 1.75 m D. 2.25 m

Solution:

mole of solute 0.50


M= =
(kg)(mass of solvent) 1 kg
250g ×
1000g
M=2 m

40. A beam of rectangular cross-section is to be cut from a circular log of diameter D.


What should be the ratio of the depth of the beam to its width for maximum strength
in pure banding?
A. sqrt. of 2 C. sqrt. of 3
B. (sqrt. of 2)/2 D. (sqrt. of 3)/3

Solution:

222
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
2
D d2 = D2
D=w√3 ;w= 3
√3 2 2 2
d2 = (w√3) = w2 (3)
d2 =D2 - w2 3 3
d
2 2 D 2 d2 = 2w2 = = √2
d =D - ( ) w
√3
41. The viscosity of a fluid varies with
A. temperature C. density
B. pressure D. temperature and pressure

42. A 8.00-L sample of gas at 99.0 kPa and 25 deg C is compressed. What is its final
pressure at 25 deg C if the gas is compressed 2.00 L?
A. 396 kPa B. 132 kPa C. 264 kPa D. 528 kPa

Solution:

P1=99KPa V1=8L V1=6L

PVT Relations (isothermal) ; T=C


P1 V1 = P2 V2
(99KPa)(8)=(P2 )(6)
P2 =132 kPa

43. What is the strong bond between hydrogen atoms known as?
A. the iconic bond C. ionic and metallic bonds
B. the metallic bond D. the covalent bond

44. Determine the moment of inertia of a circle of a diameter 5 in about a diameter.


A. 30.7 in^4 B. 61.4 in^4 C. 15.35 in^4 D. 46.02 in^4

Solution:

πd4 π (5)4
INA = = = 30.7 in4
64 64

45. Convert (11011) base 2 to base 8


A. 31 B. 27 C. 33 D.29

Solution:

(110 | 011)
(3 | 3)
=338

223
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
46. Calculate the pressure of oxygen in a mixture at 105.9 kPa containing 0.400 mol of
oxygen and 0.200 mol of nitrogen.
A. 176.5 kPa B. 141.2 kPa C. 35.2 kPa D. 70.6 kPa

Solution:
Nsol 0.4
Xsolution = = = 0.667
Ntotal 0.4+0.2
Po = xs ×P=(0.667)(105.9kPa) = 70.6kPa

47. (11100) base 2 = ( ______ ) base 16


A. 2E B. 2A C. 1C D. 1B

Solution:

(0001 | 1100)
(1 | 12=C)
=1C16

48. If a twisting moment of 10,000 lb.-in is impressed 1-¾ in diameter shaft, what is the
maximum shearing stress developed?
A. 8,500 psi B. 9,200 psi C. 9,500 psi D. 8,900 psi

Solution:
32max 32 (10, 000 lb-in)
Sb = = = 9,500 psi
π(D)3 π (2.205 in)3

49. The path of a projectile is:


A. a parabola C. a part of a circle
B. an ellipse D. a hyperbola

50. What is the pump power needed to increase the pressure by 600 kPa in a 8-cm-dia
pipe transporting0.04 cu. m/s?
A·32kW B. 24 kW C. 18 kW D. 43 kW

Solution:
Power = (v)(P)
Power = (0.04)(600,000)
P = 24,000 W or 24kW

51. A heat pump delivers 20,000 kJ/hr of heat with a 1.39 kW input. Calculate the COP.
A. 3 B. 4 C. 5 D. 6

Solution:

224
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Q
COP = ; Q=20,000 kJ/hr; Hp=1.39 kW; t=3600s
P×t
20,000
COP =
1.39 ×103 ×3,600
COP = 3.9968 ≈ 4

52. During an isentropic process, which of the following is true?


A. The temperature increases as the pressure decreases.
B. The temperature increases as the volume increases.
C. The heal transfer equals the enthalpy change.
D. The heat transfer is zero

53. Which one of the following elements has the largest atomic radius?
A. lithium C. beryllium
B. sodium D. magnesium

54. A turbine has to operate at 300 rpm under a net head of 400m. if c v = 0.98, what is
the velocity?
A.68.82 m/s C. 34.41m/s
B. 86.82 m/s D. 173.64 m/s

Solution:
cv = 0.98; net head=400m; N=300rpm
V = Cv √2gh = (0.98)(√2(9.81)(400) = 86.82 m/s

55. An object of mass 100 g is at rest. A net force of 2000 dynes is applied 10 sec. What
is the velocity?
A. 125 cm/sec C. 200 cm/sec
B. 150 cm/sec D. 250 cm/sec

Solution:

Ft = mVo
(2,000)(10)
Vo = = 200cm/s
100

56. A tank contains ail sp. gr. 0.80, gasoline sp. gr. 0.90 and seawater sp. gr. 1.03. If the
depths of the liquids are 0.5 m, 0.8 m and 1 m for oil, gasoline and seawater
respectively. Find the pressure at a depth of 1.2 m.
A. 28.124 kPa C. 16.04 kPa
B. 21.092 kPa D. 10.104 kPa

Solution:

225
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Pfluid = ρgh
density of water at 20C = 0.998 g/cm³ = 998 kg/m³
density = SG x 998 kg/m³ in each case
at 1.2 meters, you have 0.5 m of the first liquid and 0.7 of the second
P = 0.8(998)(0.5)(9.8) + 0.9(998)(0.7)(9.8)
P = (998)(9.8)(0.8•0.5 + 0.9•0.7)
P = (998)(9.8)(0.4 + 0.63)
P = (998)(9.8)(1.03) Pa = 10.104kPa

57. The minimum size of service drop copper conductors allowed by the PEC is one of
the following. Which is this?
A. 3.5 sq. mm C. 2.0 sq. mm
B. 5.5 sq. mm D. 8.0 sq. mm

58. The density of air at vacuum of 40 kPa and - 40 deg C is in kg/cu. m. Assume Patm =
100 kPa
A. 0.598 B. 0.638 C. 0.897 D. 0.753

Solution:

P 100kPa-40kPa
ρ= = = 0.897 kg/m3
RT kJ
(0.287 ) (-40+273)K
kg K
59. Varignon's theorem is used to determine the __________.
A. moment of inertia C. location of centroid
B. mass moment of inertia D. moment of area

60. A piece of machinery costs $ 20,000 and has an estimated life of eight years and a
scrap value of $ 2,000. What uniform annual amount must be set aside at the end of
each of the eight years for replacement if the interest rate is 4%?
A. $ 1,953 B. $ 2,174 C. $ 2,250 D. $ 2,492

Solution:
(Co-CL)(i)
d= ; Co=$20,000; CL=$2,000; i=0.04 or 4%
(1+i)𝑛 -1
(20,000-2,000)(0.04)
d= = $ 1,953.1
(1+0.04)8 -1
61. RA 7920, Rule 2 (d) defining?
A. CHED B. Commission C. Board of EE D. TESDA

62. A liquid which is compressed in a cylinder if it has a volume of 1,000 cu cm. (1 liter)
at 2 MPa and a volume of 990 cu. cm. at 2.5 MPa. Compute the bulk modulus of
elasticity
A. 150 MPa B. 100 MPa C. 25 MPa D. 50 MPa
226
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

P2 – P1 (2.5 – 2) kPa
E= = = 50MPa
V1 – V2 1000 990
( )-( )
V1 1003 1003
1000
( )
1003
63. Galvanized iron is a term referring to iron coated with:
A. aluminum B. magnesium C. tin D. zinc

64. Determine the work, in kJ, necessary to compress 2 kg of air from 100 kPa to 4000
kPa if the temperature is held constant 300 deg C.
A. -1210 B. -1105 C. -932 D. -812

Solution:

P1
W=mRT ln ( )
P2
kJ 100
W=(2 kg) (0.287 ) (300+273) ln ( )
kg K 4000
W= - 1213.28 kJ

65. Article III of Code of Ethics for Electrical Engineers contains:


A. SEC. 1 to 8 C. SEC. 1 to 6
B. SEC. 1 to 7 D. SEC. 1 to 5

66. Which metal is protected by a layer of its own oxide?


A. aluminum B. silver C. gold D. iron

67. A voltage level exceeding one (1) kV up to 34.5 kV is:


A. High Voltage C. Extra High Voltage
B. Low Voltage D. Medium Voltage

68. A drill press is purchased for $ 10,000 and has estimated life of twelve years. The
salvage value at the end of twelve years is estimated to be $ 1,300. Using general
straight-line depreciation, compute the book value of the drill press at the end of
eight years.
A. $1,300 B. $ 3,333 C. $ 3,475 D. $4,200

Solution:
n
Cn =Co – (C – CL )
L o
8
C8 = 10,000 - (10,000-1,300)
12
C8 = $ 4,200
227
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
69. Another counting 0, 1, 10, 11 the next binary number is
A. 15 B. 110 C. 100 D. 120

70. A force causing a rise of a liquid in tubes of small diameter.


A. cohesion B. surface tension C. capillarity D. adhesion

71. A skier starts from rest and slides 9.0 m down a slope in 3.0 s. in what time starting
will the skier acquire a speed of 24m/s? Assume that the acceleration is constant.
A. 8 s B. 10 s C. 16 s D. 12 s

Solution:

V=Vo +at
1
9 = - at2
2

g(2) 2m 24
a= =- t= =12 sec
3 2 s2 2
2m
-a = 2
s
24 = 2t

72. An engineer buys a machine costing P 500,000. Compute the capitalized cost if the
machine has a life of 5 years and a salvage value of P 80,000. Rate of interest is
12% per annum.
A. P 1,505,964.80 C. P 1,050,934.06
B. P 1,800,836.08 D. P 936,280.60

Solution:

50,000 - 80,000
CC = 50,000 +
1.255 -1
CC = P1,050,934.06

73. Accounting book in which are recorded the credits and debits of commercial
transactions.
A. ledger C. balance
B. journal D. clerk’s book

74. An aluminum bar 6 ft. long has a 1-in-square cross-section over 2 ft. of its length and
a 1-in-diameter circular cross-section over the other 4 ft. how much will the bar
elongate under a tensile load P = 3,500 lb. if E = =10.5 x10^6 psi?
A. 0.00284 in B. 0.00389 in C. 0.0284 in D. 0.0389 in

228
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
PL (3500)(4×12)
δ= δ2 = π 2 = 0.020371
AE ( 1 ) (10.5×106 )
(3500)(2 × 12) 4
𝛿1 = = 8 × 10−3 δ=δ1 +δ2 =8×10-3 + 0.0203718 = 0.0284
(1)(10.5 × 106 )
75. A ball is thrown with an initial velocity of 30 m/sec from a height of 3 m above the
ground, and 40 m from a vertical wall. How far from the wall will the ball rebound for
the first time?
A. 23.46 m B. 16.54 m C. 32.46 m D. 61.54 m

Solution
1
y= Vo sin(θ) t- 2 gt2
x = 23.46
1 2
-3 = 30 sin(0) t- 2 gt R = 40-x = 40-23.46
t = 0.78 sec R = 16.54 m
x = 30 cos(0) (0.75)
76. RA 7920 contains how many sections all in all
A. 40 B. 41 C. 43 D. 45

77. The most important element that controls the physical properties of steel is
A. Silicon B. Tungsten C. Manganese D. Carbon

78. A stone of mass 100 grams is whirled in a horizontal circle at the end of a cord 100
cm long. If the tension in the cord is 2.5 newtons, what is the speed of the stone?
A.3 m/s B. 4 m/s C. 5 m/s D. 6 m/s

Solution:
F = ma v2
a=
F 2.5 N 25m L
a= = = v = √aL= √(25)(1) = 5m/s
m 0.1 kg s
79. A student will receive P 3,000 at the beginning of each 3 months for 4 years. What is
the sum of this annuity at the end of the 4th year if the interest rate is 6%
compounded quarterly?
A. P 45,604 B. P 54,604 C. P 64,320 D. P 46,690

Solution:

0.06 4×4+1
(1+i)n+1 -1 (1+
4
) -1
F=A ( -1)= F=3000 ( 0.06 -1) = P54,604.07
i
4

Two men lift the ends of a 20 ft. beam weighing 200 lb. onto their shoulders. Both
men are of the same height so that the beam is carried horizontally, but one is much

229
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
the stronger of the two and wishes to bear 50% more of the weight than his mate.
How far from the end of the beam should he put his shoulder?
A. 2-½ ft. B. 1-½ft. C. 4-1/3ft. D. 3-1/3 ft.

Solution:
-1.5(F1 )(10+X)+6440(10)=0
ByFBD: F2 =1.5F1 6440X
Taking the moment at F2 -1.5 ( ) (10+X)+6440(10)=0
10+X
F1 (10+X)-6440(X)=0 6.667
Moment at F1 X= =3.333 ≈ 313 f
2
-F2 (10+X)+6440(10)=0

81. Which is the scalar quantity


A. force B. energy C. displacement D. velocity

82. A fluid property which refers to the intermolecular attraction by which the separate
particles of the fluid are held together:
A. cohesion B. adhesion C. capillarity D. tension

Explanation:
The force of cohesion is defined as the force of attraction between
molecules of the same substance.
The force of adhesion is defined as the force of attraction between different
substances, such as glass and water.
Capillary Action is due to both the cohesive forces between liquid
molecules and adhesive forces of liquid molecules.
Tension may be described as the pulling force transmitted axially by the
means of a string, cable, chain, or similar one-dimensional continuous object, or
by each end of a rod, truss member, or similar three-dimensional object

83. When the velocity of an object is tripled, another quantity which is tripled at the same
time is the objects:
A. momentum B. potential energy C. kinetic energy D. mass

84. A 20-kg piston rests on a sample of gas in a cylinder 10 cm in radius. The absolute
pressure on the gas is
A. 0.0064 bar B. 0.062 bar C. 1.019 bar D. 1.075 bar

Solution:
Pg =0.06245 bar
F mg
P= = ; m=20kg; r=10cm Patm =1
𝐴 𝐴
(20)(9.81) N 1 bar Pabs =1 + 0.06245
P= =6,245.24 m2 ×
10 2
π( )
N
105 2 Pabs =1.06245
100 m
85. The electric power industry is divided into how many sectors?
A. 3 B. 4 C. 5 D. 6

230
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:

The electric power industry shall be divided into four (4) sectors, namely:
generation; transmission; distribution and supply.

86. A substance existing the gaseous phase but relatively near its saturation
temperature is known as:
A. Gas B. Water C. Steam ` D. Vapor

87. How many atoms are there per unit cell for a face-centered cubic structure?
A. 1 B. 2 C. 3 D. 4

Explanation:

The hexagonal closest packed (hcp) has a coordination number of 12 and


contains 6 atoms per unit cell. The face-centered cubic (fcc) has a coordination
number of 12 and contains 4 atoms per unit cell. The body-centered cubic (bcc)
has a coordination number of 8 and contains 2 atoms per unit cell

88. Two masses 10.0 kg and 1.0 kg, respectively, are located 1.0 m apart. The
gravitational force that each mass exerts on the other is
A.6.7 x 10^-9 N C. 6.7 x 10^-11 N
B. 6.7 x 10^-10 N D. 6.7 x 10^-12 N

Solution:
(10)(1)
G=6.67×10-11 ; m1 = 10; m2 = 1 𝑡 F=(6.67×10-11 ) ( )
12
=1 F= 6.67×10-10 N
m1 m2
F=G 2
s

89. Funds supplied and used by owners of an enterprise in the expectation that a profit
will be earned
A. equity capital C. save
B. credit D. Investment

90. Work is measured in the same units as


A. force B. momentum C. mass D. energy

91. The critical angle is the angle of incidence that produces an angle of refraction of
A. 0 deg B. 45 deg C. 60 deg D. 90 deg

92. A concrete test cylinder having length L=12 in and diameter d=6 in is subjected to
axial compressive forces P in a testing machine. If the maximum shear stress in the
concrete is not to exceed 2,000 psi, what is the safe value for the axial load p?
A. 452,389 lb. B. 113,100 lb. C. 904,778 lb. D. 56,550 lb.

231
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
Solution:
P
S= ; S=2000; d=6in L=12in
A
π
P =(2000) [ ×62 ]
4
P=(56548.67)(2)
P=113,097.34 lb

93. If an object is moving north, the direction of the frictional force is


A. north B. south C. east D. west

94. The overall energy program formulated and updated yearly by the DOE and
submitted to Congress pursuant to RA. 7638
A. Philippine Energy Plan (PEP)
B. Power Development Program (PDP)
C. Preliminary Project Planning Data (PPPD)
D. Philippine Electrical Code (PEC)

95. Oxygen boils at -183 deg C. This temperature is


A. -215 deg F B. -297 deg F C. -329 deg F D. -361 deg F

Solution:
9 9
°𝐹 =5 °𝐶 +32 °𝐹 =5 (−183) + 32 °𝐹 = -297.4

96. What is the distance between two consecutive points in phase on a wave called?
A. frequency C. amplitude
B. period D. wavelength

Explanation:

The wavelength in a longitudinal wave is the distance between two consecutive


points that are in phase. The wavelength in a longitudinal wave refers to thedistance
between two consecutive compressions or between two consecutive rarefactions.
Amplitude. The amplitude is the maximum displacement from equilibrium.

97. Waves in a lake are 5.00 m in length and pass an anchored boat 1.25 s apart. The
speed of the wave is

A. 0.25 m/s B. 4.00 m/s C. 6.25 m/s D. 5.75 m/s

Solution:
l 5
v= = = 4m/s
t 1.25
98. A square bar of aluminum 2 in on a side and 10 in long is loaded by axial tensile
forces at the ends. Experimentally, it is found that the strain in the direction of the
232
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
load is 0.001 in/in. Determine the volume of the bar when the load is acting.
Consider μ=0.33.
A. 40 cu. in. C. 39.9864 cu. in.
B. 40.0136 cu. in D. 39.9728 cu. in.

Solution:

P ∆V = (22 x10)[(0.001)](1 − 2(. 33))


S = Ee , S =
A ∆V = 0.136 in3
P new V
= Ee , P = AE
A V + ∆V
∆V P V = (22 )(10) + (.0136)
=e= (1 − 2μ)
V AE V = 𝟒𝟎. 𝟎𝟏𝟑𝟔 𝐢𝐧𝟑
AEε
∆V = V [ ] (1 − 2μ)
AE
99. The temperature of an object is raised by 90 deg C. This is equivalent to an increase
in its Fahrenheit scale of
A. 194 B. 130 C. 162 D. 50

Solution:
°F2 = 194°F
9 9
F1 = °C+32; °F1 = (0)+32 °F = °F2 - °F1
5 5
°F1 = 32°F °F=194-32
9 °F=162°F
°F2 = (90)+32
5
100. Determine the largest allowable square cross section of a steel shaft of length 6 m
if the maximum shearing stress is not exceeding 120 MPa when the shaft is twisted
through one complete revolution. Use G = 77.2 GPa.
A. 2.20 mm B. 1.20 mm C. 3.55 mm D. 0.86 mm

Solution:

233
REGISTERED ELECTRICAL ENGINEERS PRE-BOARD EXAMINATION
AUGUST 2012
ENGINEERING SCIENCES AND ALLIED SUBJECTS
4.81T Sa3
SS = ; T=
a3 4.81
7.10TL θa4 G
θ= ; T=
a4 7.10L
Equating both equations:
(120×106 )a3 2π a4 (77.2×109 )
=
4.81 7.10 (6)
-3
a = 2.19×10 m ≈ 2.2 mm

Вам также может понравиться