Академический Документы
Профессиональный Документы
Культура Документы
Causes:
1. Unstable power source
2. Low/High voltage
3. Broken thermistor wire
4. Poor contact in the thermistor connector terminals.
5. Heater lamps are broken or not installed correctly.
Before resetting "6XXX" series code, make sure that defective parts have
been replaced/repaired.
Reset Procedure:
Enter 1087-1087 (1087 twice) from the keypad.
Enter 163 by using keypad.
Press "Start" (the green button) twice.
The machine will restart automatically.
C0030 Fax PWB Problem. Processing with fax software is disabled due to
software or hardware issues.
C0060 Main PWB Type Mismatch Error.
C0070 Fax PWB Incompatability Detection Problem. Fax software is not
compatible with main PWB software.
C0130 Main PWB EEPROM Backup Memory Device Problem. EEPROM can
not be written or read.
C0140 Main PWB EEPROM Backup Memory Data Problem. Abnormal reading
data from EEPROM.
C0150 Engine PWB EEPROM Backup Memory Device Problem. EEPROM
cannot be written or read.
C0160 Engine PWB EEPROM Backup Memory Data Problem. Abnormal
reading data from EEPROM. Read & write data do not match five times
consecutively.
C0170 Copy Counts Problem. A checksum error is detected in the main and
engine backup memories for copy counters.
C0180 Machine Number Mismatch Error. Machine number does not match on
main and engine PWBs
C0600 Main PWB DIMM Installed Incorrectly.
C0610 Main PWB DIMM error
C0630 DMA transmission of compressed, decompressed, rotated, relocated, or
blanked-out image data does not complete within a specified period of
time.
C0640 Hard Disk Drive cannot be accessed
C0700 Optional CF backup is not suitable.
C0800 Image processing problem. JAM05 is detected twice.
C0830 Fax Flash ROM program area checksum error
C0870 Fax PWB to Main PWB high capacity data transfer problem.
C0880 Fax PWB program archive problem.
C0920 Fax backup data is not retained.
C1010 Cassette #1 Lift Motor error. Exceeds 12 seconds of operation or 500ms
of overcurrent.
C1020 Cassette #2 Lift Motor error. Exceeds 12 seconds of operation or 500ms
of overcurrent.
C1030 PF-700 optional cassette #3 lift motor error.
C1040 PF-700 optional cassette #4 lift motor error.
C1100 PF-750 (Left) Lift Motor 1 error. Exceeds 1 second overcurrent.
C1110 PF-750 (Right) Lift Motor 2 error. Exceeds 1 second overcurrent.
C1120 PF-750 (Left) Lift Motor 1 position problem. PF switch 2 remains off
after 30 seconds of motor operation.
C1130 PF-750 (Right) Lift Motor 2 position problem. PF switch 1 remains off
after 30 seconds of motor operation.
C1800 PF-700/PF-750 Communication Problem.
C1900 PF-700 EEPROM error. Write data & Read data are not in agreement
three times consecutively.
C2000 Drive Motor Problem. Stable Off is detected exceeding 1 sec after motor
stability. Stabilization is not detected with 6 sec of activation.
C2250 Main Charge Cleaner Motor error. Lock error is detected three times in a
row during cleaner motor operation.
C2500 Paper Feed Motor error. Stable Off is detected exceeding 1 sec after motor
stability. Stabilization is not detected within 6 seconds of activation.
C3310 CIS AGC Problem. After AGC correct input is not obtained at the CIS.
C3500 Communication Error Between Scanner and SHD.
C3900 Scanner PWB Backup Memory Read/Write Problem. Read & Write data
does not match.
C3910 Scanner PWB Backup Memory Data Problem. Data in a specified area of
the backup memory does not match the specified values.
C4000 Polygon Motor Synchronization Problem. Polygon motor does not
stabilize speed within 20 sec of activation.
C4010 Polygon Motor Steady-State Problem. Stable Off is detected for 20 sec
continuously after polygon motor stabilization.
C4200 BD Steady-State Problem. ASIC detects a Beam Detect error A for 2 sec
after polygon motor stabilization.
C5300 Cleaning Lamp Broken Wire. While the cleaning lamp is On, the broken
wire detection signal is detected for 2 sec continuously.
C6000 Fuser Heater Break. Thermistor1 detected less than 70C/158F for 10 sec
during warmup & ready. Thermistor2 detected less than 40C/104F for 10
sec during warmup & ready. Temp at thermistor 1or 2 does not rise by at
least 1C/1.8F within 5 sec.
C6020 Abnormally High Thermistor Temperature. Thermistor 1 or 2 is detected
250C/482F for 40ms or more.
C6030 Fixing Thermistor Break Error. Thermistor break signal is detected for 1
sec.
C6050 Abnormally Low Thermistor Temperature. Thermistor 1 is detected
80C/176F or less for 1 sec continuously during copying.
C6400 Zero-Cross Signal Error. While fuser heater On/Off control is performed,
the zero-cross signal is not input within 3 sec.
C6410 Fuser Unit Connection Insertion Problem. Absence of fuser unit is
detected.
C6420 Fuser Unit Fuse Cut Problem. The fuse has been cut 33 sec after the fuse
cut signal is turned on.
C7300 Toner Container Problem. Toner level is not detected when toner empty is
detected.
C7400 Developing Unit Connection Insertion Problem. Absence of the
developing unit is detected.
C7410 Drum Unit Connection Insertion Problem. Absence of the drum unit is
detected.
C7800 Broken External Thermistor Wire. Thermistor on the environmental
sensor outputs 4.5v or more.
C7810 Short-Circuited External Thermistor. Thermistor input value is 0.5v or
less.
C7900 Drum EEPROM Error. Reading or writing to the EEPROM cannot be
performed.
C7910 Developing EEPROM Error. Reading or writing to the EEPROM cannot
be performed.
C8020 DF-710 Punch Motor Problem. Punch motor lock signal is detected for
500ms or more during activation.
C8030 DF-730 Tray Upper Limit Detection Problem. When tray elevation motor
raises a tray, the upper limit switch detects On condition.
C8050 DF-710 Paper Conveying Belt Motor 1 Error. Paper conveying belt home
position sensor 1 does not turn Off within 1.5 sec. Paper conveying belt
home position sensor 1 does not turn On within 2.5 sec. Jam 88.
C8060 DF-710 Paper Conveying Belt Motor 2 Error. Paper conveying belt home
position sensor 2 does not turn Off within 1.5 sec. Paper conveying belt
home position sensor 2 does not turn On within 2.5 sec.
C8070 DF-710 Internal Tray Communication Error. The connection is detected,
but communication is not possible with the internal tray.
C8140 DF-710 Main Tray Problem. Main tray is not detected in not detected by
main tray top limit detection sensor or main tray capacity detection sensor
within 20 sec of ascending. Main tray upper limit detection sensor or main
tray load detection sensor is not detected as Off within 20 sec of main tray
descending. Main tray lower limit detection sensor is not detected as On
within 20 sec of main tray descending. Main tray upper limit detection
sensor or main tray load detection sensor remain on for 2 sec or more
during main tray ascent.
C8140 DF-730 Tray Elevation Motor Problem. Tray lower limit sensor or surface
view sensor cannot be detected within 10 sec.
C8170 DF-710 Side Registration Motor 1 Problem. During initial rotations home
position is not detected within 3 sec. Jam 88.
C8170 DF-720 Front Side Registration Motor Problem. During initial rotations
home position is not detected within 106 pulses. When the front side
home position sensor is turned off during initialization, the sensor did not
turn on within 3 sec.
C8170 DF-730 Adjustment Motor Problem. Adjustment motor home position
motor is not detected within a specific time during activation.
C8180 DF-710 Side Registration Motor 2 Problem. During initial rotations home
position is not detected within 3 sec. Jam 88.
C8180 DF-720 Rear Side Registration Motor Problem. During initial rotations
home position is not detected within 106 pulses. When the rear side home
position sensor is turned off during initialization, the sensor did not turn
on within 3 sec.
C8190 DF-720 Trailing Edge Registration Motor Problem. During initial
rotations home position is not detected within 106 pulses. When the
trailing edge home position sensor is turned off during initialization, the
sensor did not turn on within 3 sec.
C8210 DF-710 Stapler Moving Motor 1 Error. During initial rotations home
position is not detected within 1.5 sec.
C8210 DF-720 Finisher Stapler Problem. Stapler home position sensor does not
change state from non-detect to detect within 200ms of forward (CCW)
rotation. During initial rotations stapler home position detection does not
change state from non-detect to detect within 600ms of reverse (CW)
rotation.
C8210 DF-730 Stapler Problem. Home position is not detected within a specific
time of activation.
C8220 DF-710 Stapler Moving Motor 2 Error. During initial rotations home
position is not detected within 3.5 sec.
C8230 DF-710 Stapler Motor Problem. Jam 82 is indicated.
C8300 BF-710 Centerfold Unit Communiation Error. Although the connection is
detected, communication is not possible with the centerfold unit.
C8310 BF-710 Centerfold Side Registration Motor 1 Problem. During initial
rotations home position is not detected within 1000ms.
C8320 BF-710 Centerfold Paper Conveying Belt Motor Problem. During initial
rotations home position is not detected within 2500ms.
C8330 BF-710 Blade Motor Problem. During initial rotations home position is
not detected within 1500ms.
C8340 BF-710 Centerfold Staple Motor Problem. Jam 89.
C8350 BF-710 Centerfold Side Registration Motor 2 Problem. During initial
rotations home position is not detected within 1000ms.
C8360 BF-710 Centerfold Main Motor Problem. The motor lock signal is
detected for more than 1000ms during activation.
C8440 DF-730 Sensor Adjusting Problem. The paper entry sensor cannot be
adjusted within the specified range.
C8460 DF-730 EEPROM Problem. Reading to or writing from EEPROM cannot
be performed.
C8500 MT-710 Communication Error. The connection is detected, but
communication is not possible with the mailbox.
C8510 MT-710 Drive Motor Problem. The motor lock signal is detected for more
than 500ms during activation.
C8800 DF-710 Communication Problem. No communication: there is no reply
after (5) tries. Abnormal communication: a parity or checksum error is
detected (5) times in succession.
C8900 DF-710 Backup Memory Data Problem. Read and write data does not
match.
C8910 PH-5A Backup Memory Data Problem. Read and write data does not
match.
C8920 MT-710 Backup Memory Data Problem. Read and write data does not
match.
C8930 BF-710 Backup Memory Data Problem. Read and write data does not
match.
C9000 DP-700 Communication Problem. A communication error is detected.
C9040 DP-700 Lift Motor Ascent Error. The DP lift upper limit switch is not
detected within 10000 pulses. After a one time retry, the DP lift upper
limit switch could not be turned On.
C9050 DP-700 Lift Motor Descent Error. The DP lift lower limit switch is not
detected within 10000 pulses. After a one time retry, the DP lift lower
limit switch could not be turned On.
C9060 DP-700 EEPROM Error. Read and write data does not match. Data in the
specified area of the backup memory does not match the specified values.
E00462 or U00462 Fax Communication Error: Ecryption reception was interrupted because
the encryption key for the specified encryption box was not registered.
E00500 or U00500 Fax Communication Error: Multiple communication was interrupted and
the call was not made on destination units after interruption.
E00600 or U00600 Fax Communication Error: The document processor cover is open.
E00601 or U00601 Fax Communication Error: Document jam or the document length
exceeds the maximum.
E00602 or U00602 Fax Communication Error: Image scanning section problem
E00604 or U00604 Fax Communication Error: Document length exceeded the limit of the
bitmap memory capacity.
E00610 or U00610 Fax Communication Error: Recording section cover open.
E00655 or U00655 Fax Communication Error: CTS was not activated after RTS due to a
modem error.
E00656 or U00656 Fax Communication Error: Data was not transmitted after CTS was
activated due to a modem error.
E00670 or U00670 Fax Communication Error: Power was cut off during communication.
E00677 or U00677 Fax Communication Error: There was no file to transmit in the memory
transmission mode.
E00690 or U00690 Fax Communication Error: System error.
E00910 or U00910 Fax Communication Error: A page reception error occurred in G3 mode.
A page reception error remained after retry of transmission in ECM mode.
E03300 or U03300 Fax Communication Error: In polling reception from a unit of our make,
operation was interrupted due to a mismatch in permit ID number or
telephone number.
E03300 or U03300 Fax Communication Error: In interoffice subaddress-based bulletin board
reception, operation was interrupted due to a mismatch in permit ID
number or telephone number.
E03400 or U03400 Fax Communication Error: Polling reception was interupted because of a
mismatch in individual numbers.
E03500 or U03500 Fax Communication Error: In confidential polling reception, the specified
confidential box number was not registered in the destination.
E03500 or U03500 Fax Communication Error: In interoffice subaddress-based bulletin board
reception, the specified subaddress confidential box number was not
registered in the destination unit.
E03500 or U03500 Fax Communication Error: The destination was being accessed.
E03600 or U03600 Fax Communication Error: Confidential polling reception was interrupted
because of a mismatch in specified confidential box numbers.
E04100 or U04100 Fax Communication Error: Confidential transmission failed because the
destination unit had no confidential capability.
E04100 or U04100 Fax Communication Error: Subaddress-based transmission failed because
the destination unit had no subaddress-based reception capability.
Send FTP Error 1102 Error: Username/Password. Domain name is not entered.
Send FTP Error 1103 Error: Pathname or File Name. Connect to the folder which is not
permitted for reference/writing.
Send FTP Error 1103 Error: Pathname or File Name. Assign disable folder path.
Send FTP Error 1105 Error: Not Supported Protocol. FTP protocol is set to OFF.
Send FTP Error 2101 Error: Can Not Connect. Enter the disable host name/IP address.
Send FTP Error 2101 Error: Can Not Connect. Assign the wrong port number.
Send FTP Error 2101 Error: Can Not Connect. Network is not connected.
Send FTP Error 2102 Error: Cannot Connect With Timeout. The server is unable to
communicate.
Send FTP Error 2102 Error: Cannot Connect With Timeout. Send the server which does not
support FTP server.
Send FTP Error 2103 Error: Response Wait With Timeout. The server is unable to
communicate.
Send FTP Error 2201 Error: Network Transfer. Error occurs on the network.
Send FTP Error 2202 Error: Network Transfer With Timeout. Error occurs on the network.
Send FTP Error 2203 Error: Response Wait With Timeout. Response is not returned from the
server, above specified time.
Send FTP Error 3101 Error: Server Response. The server is error status.
Send FTP Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds
999 pages.
Send email Error Error: Host Name. SMTP server name is not set. Error SMTP server
1101 name.
Send email Error Error: Username/Password. User ID for the authentication is not entered
1102 or entered wrongly. Wrong authentication password is entered.
Send email Error Error: No Recipient Address. The destination address is not specified.
1104
Send email Error Error: Not Supported Protocol. SMTP protocol is set to OFF.
1105
Send email Error Error: No Sender Info. Sender address is not entered.
1106
Send email Error Error: Can Not Connect. Select [Other Authenticate] when authenticating
2101 POP before SMTP.
Send email Error Error: Can Not Connect. The specified server is not SMTP server.
2101
Send email Error Error: Can Not Connect. Network is not connected.
2101
Send email Error Error: Cannot Connect With Timeout. The server is unable to
2102 communicate.
Send email Error Error: Response Wait With Timeout. The server is unable to
2103 communicate.
Send email Error Error: Network Transfer. Error occurs on the network.
2201
Send email Error Error: Network Transfer With Timeout. Error occurs on the network.
2202
Send email Error Error: Response Wait With Timeout. Response is not returned from the
2203 server, above specified time.
Send email Error Error: Email Size Limit. The size of the email attachment exceeds its
2204 limit.
Send email Error Error: Server Response. The server is error status.
3101
Send email Error Error: Server Response. Server setting is not authenticated normally.
3101
Send email Error Error: Not Found Authentication Mechanism. Unsupported SMTP
3201 Authentication Mechanism is found.
Send email Error Error: Page Max Count Over. The number of pages of a send file exceeds
9181 999 pages.
TWAIN Error 2202 Error: Network Transfer With Timeout. Response is not returned from the
server, above the specified time.
TWAIN Error 9181 Error: Page Max Count Over. The number of pages of a send file exceeds
999 pages.
Software Error 5101 Error: Not Yet Connected. Operation handle error. Error for stored status
in the operation handle.
Software Error 5102 Error: Already Connected. Operation handle error. Error for stored status
in the operation handle.
Software Error 5103 Error: Not Yet Opened. Error for storage status in the operation handle.
Software Error 5104 Error: Already Opened. Error for storage status in the operation handle.
Software Error 7102 Error: Socket Create. Unable to create a communication socket.
Software Error 720f Error: Unknown Error. Unable to determine the cause.
Send error. Job is Send Email Error: Host Name. SMTP server name is not set. Error SMTP
cancelled. Press server name.
[End]. 1101
Send error. Job is Send FTP Error: Host Name. Enter the disable host name/IP address.
cancelled. Press
[End]. 1101
Send error. Job is Send Email Error: Username/Password. User ID for the authentication is
cancelled. Press not entered or entered wrongly. Wrong authentication password is
[End]. 1102 entered.
Send error. Job is Send SMB/FTP Error: Username/Password or Shared Name/Folder
cancelled. Press Name. Domain name is not entered.
[End]. 1102
Send error. Job is Send SMB/FTP Error: Username/Password or Shared Name/Folder
cancelled. Press Name. Assign disable user/password.
[End]. 1102
Send error. Job is Send SMB Error: Username/Password or Shared Name/Folder Name.
cancelled. Press Assign disable shared name.
[End]. 1102
Send error. Job is Send SMB Error: Username/Password or Shared Name/Folder Name.
cancelled. Press Host name error.
[End]. 1102
Send error. Job is Send SMB/FTP Error: Pathname or File Name. Domain name is not
cancelled. Press entered.
[End]. 1103
Send error. Job is Send SMB/FTP Error: Pathname or File Name. Connect to the folder
cancelled. Press which is not permitted for reference/writing.
[End]. 1103
Send error. Job is Send SMB/FTP Error: Pathname or File Name. Assign disable folder
cancelled. Press path.
[End]. 1103
Send error. Job is Send Email Error: No Recipient Address. The destination address is not
cancelled. Press specified.
[End]. 1104
Send error. Job is Send Email Error: Not Supported Protocol. SMTP protocol is set to OFF.
cancelled. Press
[End]. 1105
Send error. Job is Send SMB Error: Not Supported Protocol. SMB protocol is set to OFF.
cancelled. Press
[End]. 1105
Send error. Job is Send FTP Error: Not Supported Protocol. FTP protocol is set to OFF.
cancelled. Press
[End]. 1105
Send error. Job is Send Email Error: No Sender Info. Sender address is not entered.
cancelled. Press
[End]. 1106
Send error. Job is Send Email Error: Can Not Connect. Network is not connected.
cancelled. Press
[End]. 2101
Send error. Job is Send Email Error: Can Not Connect. Select [Other Authenticate] when
cancelled. Press authenticating POP before SMTP.
[End]. 2101
Send error. Job is Send Email Error: Can Not Connect. The specified server is not SMTP
cancelled. Press server.
[End]. 2101
Send error. Job is Send SMB/FTP Error: Can Not Connect. Enter the disable host name/IP
cancelled. Press address.
[End]. 2101
Send error. Job is Send SMB/FTP Error: Can Not Connect. Assign the wrong port number.
cancelled. Press
[End]. 2101
Send error. Job is Send SMB/FTP Error: Can Not Connect. Network is not connected.
cancelled. Press
[End]. 2101
Send error. Job is Send Email/ FTP Error: Cannot Connect With Timeout. The server is
cancelled. Press unable to communicate.
[End]. 2102
Send error. Job is Send FTP Error: Cannot Connect With Timeout. Send the server which
cancelled. Press does not support FTP server.
[End]. 2102
Send error. Job is Send Email/ SMB/ FTP Error: Response Wait With Timeout. The server
cancelled. Press is unable to communicate.
[End]. 2103
Send error. Job is Send Email/ SMB/ FTP Error: Network Transfer. Error occurs on the
cancelled. Press network.
[End]. 2201
Send error. Job is Send Email/FTP Error: Network Transfer With Timeout. Error occurs on
cancelled. Press the network.
[End]. 2202
Send error. Job is Send TWAIN Error: Network Transfer With Timeout. Response is not
cancelled. Press returned from the server, above the specified time.
[End]. 2202
Send error. Job is Send Email/FTP Error: Response Wait With Timeout. Response is not
cancelled. Press returned from the server, above specified time.
[End]. 2203
Send error. Job is Send Email Error: Email Size Limit. The size of the email attachment
cancelled. Press exceeds its limit.
[End]. 2204
Send error. Job is Send Email/FTP Error: Server Response. The server is error status.
cancelled. Press
[End]. 3101
Send error. Job is Send Email Error: Server Response. Server setting is not authenticated
cancelled. Press normally.
[End]. 3101
Send error. Job is Send Email Error: Not Found Authentication Mechanism. Unsupported
cancelled. Press SMTP Authentication Mechanism is found.
[End]. 3201
Send error. Job is Send Software Error: Not Yet Connected. Operation handle error. Error
cancelled. Press for stored status in the operation handle.
[End]. 5101
Send error. Job is Send Software Error: Already Connected. Operation handle error. Error
cancelled. Press for stored status in the operation handle.
[End]. 5102
Send error. Job is Send SoftwareError: Not Yet Opened. Error for storage status in the
cancelled. Press operation handle.
[End]. 5103
Send error. Job is Send Software Error: Already Opened. Error for storage status in the
cancelled. Press operation handle.
[End]. 5104
Send error. Job is Send Software Error: Socket Create. Unable to create a communication
cancelled. Press socket.
[End]. 7102
Send error. Job is Send Software Error: Unknown Error. Unable to determine the cause.
cancelled. Press
[End]. 720f
Send error. Job is Send Email/ SMB/ FTP/ TWAIN Error: Page Max Count Over. The
cancelled. Press number of pages of a send file exceeds 999 pages.
[End]. 9181
"Acceptable staple Is the acceptable staple count exceeded?
count exceeded."
"Cannot connect to
Authentication
Server."
"Cannot duplex print Did you select a paper size/type that cannot be duplex printed?
on this paper."
"Check the document Is the document processor open? Is the top cover of the document
processor." processor open?
"Clean the slit glass." Dirt has been identified on the slit glass.
"Empty the punch The punch waste box of the 3,000 sheet finisher is full.
waste box."
"Failed to specify Job Job accounting is not specified in the print driver.
Accounting."
"Fax box limit Fax box is full, and no further storage is available.
exceeded."
"Finisher tray is full Is the acceptable storage capacity exceeded for the document finisher
of paper." tray?"
"Folding tray is full Is the acceptable storage capacity exceeded for the folding tray of the
of paper." 3,000 sheet document finisher?"
"Hard Disk error. Job An error has occurred on the hard disk.
is cancelled. Press
[End] ##"
"Incorrect Login User
Name or Password."
"Job Accounting The print count exceeded the acceptable count restricted by Job
restriction exceeded." Accounting.
"Job Separator is full Is the maximum capacity of the job separator tray exceeded?
of paper."
"KPDL error." A PostScript error has occurred.
"Mailbox tray is full
of paper."
"Memory card error." Was the memory card (Compact Flash) removed while being accessed?
Was a valid memory card inserted?
"Memory card error. Memory Card Error: Format error.
Job is cancelled.
Press [End]. Code: 01
"Memory card error. Memory Card Error: Insufficient memory card space to complete this
Job is cancelled. operation.
Press [End]. Code: 04
"Memory is full." Unable to continue the job, as the memory is used up."
"Memory Is Low" Logic Lockup
"Paper Jam. ###" Make a note of the jam location number displayed on the panel. Leave the
machine On.
"Print overrun." Warning. Low printer memory.
"Removable memory An error has occurred on the USB stick memory or Compact Flash
error." memory.
"Removable memory
was removed."
"Reset all originals in Are there any originals left in the document processor?
the document
processor."
"Scanner memory is Scanning cannot be performed due to insufficient memory for the scanner.
full." Is the acceptable scanning count exceeded?
"Scanner Paused" DMA transmission of compressed, ecompressed, rotated, relocated, or
blanked-out image data does not complete within a specified period of
time.
"Set the folding tray." Is the folding tray correctly installed to the 3,000 sheet capacity document
finisher?
"Set the folding unit." Is the folding tray correctly installed to the 3,000 sheet capacity document
finisher?
"Set the punch waste The waste toner box is not installed correctly.
box."
"Set the waste toner The waste toner box is not installed correctly.
box."
"Staple error." The location of the jam will be indicated on the panel. Leave the machine
On.
"Staple jam." The location of the jam will be indicated on the panel. Leave the machine
On.
"The ID is not The account ID# does not match.
registered."
"The memory card is Is the removable memory formatted by this machine?
not formatted."
0xFB33 Component: Panel. Category: KI-Panel. Cut off of the communication with the
controller is detected - waiting to receive: select () OK return, recv() RX data
length 0. Blue back screen. Cannot enter maintenance mode.
0xFB34 Component: Panel. Category: KI-Panel. Time out for Response telegraphic
message (could not receive response telegraphic message within a fixed time).
In case on not through httpd, this error occurs (in case it does not become CGI
time out).
CF080 Flash ROM Error (during download). Defective flash ROM (which?).
CF131 Component: PCM. Category: OS. Failure to acquire Entity data with "dbinit,
hostif_stat_chg" comand.
CF14F Component: OS. Category: OS. Primary supply voltage dropped off
temporarily and recovery operation was not stable. If the input power supply
voltage is not stable of the Main SW is turned Off/On quickly (about 1
second), this problem occurs.
CF1FF Component: SVI. Category: LioPanel. Logical Error (In case of given
parameter is NULL).
CF257 Component: LFM. Category: FaxSys. KUIOLIB error. Poor contact at the fax
card card due to mis-installation.
CF257 Fax System M IOBL error or KUIOLIB error. Poor contact at the fax card card
due to mis-installation.
CF26F Component: PrintSys. Category: PrintSys. It occurs when the error noticed
from VideoDriver. Use by Video_Driver class: Function name, factor can be
found by the detail code.
CF26F Print System Other Errors. Bug of v.2.03B has been fixed by v. 2.04A (Booklet
> Booklet Print).
CF321 Component: LioFax. Category: FaxSys. Segment code for LioFax initialization
is different from "03KH".
CF323 Component: LioFax. Category: FaxSys. Return address of Page class when
doing FAX Tx/Rx is other abnormal error. Entity (Config, BOX, etc.) access
error.
CF324 Component: LioFax. Category: FaxSys. Entity parameter error.
CF325 Component: LioFax. Category: FaxSys. In case that the time when Error came
back from LFM.
CF423 Component: FaxJOB. Category: FaxSys. As the error came back at IF for
DocumentBox, JobInfo, Config Entity.
CF423 Component: FaxJob. Category: FaxSys. The error came back when accessing
(obtaining data, setting data) to below Entity related:
job_ent(JobModel,JobInfo), config_ent, reservation, account(certificate),
document_box.
CF423 Fax System M Error. Wrong data or value detected when the following
function is used. Or poor contact at fax card due to mis-installation.
CF423 Fax System M Error. The IF error detects during system authentication from
ACT_Account_Manager. Or poor contact at fax card due to mis-installation.
CF424 Component: FaxJob. Category: FaxSys. As the error came back when
obtaining IF for system authentication from ACT_Account_Manager.
CF424 Component: FaxJob. Category: FaxSys. The date obtained from the below
Entity related is unexpected data: job_ent(JobInfo).
CF427 Component: FaxJob. Category: FaxSys. The error came back for the IF of
LioFax observer addition/deletion.
CF42F Component: FaxJob. Category: FaxSys. As handing over of the NULL pointer
in the class occurred. As memory reservation with new in heap domain is
failed: Assert for preventing from segment drop off.
CF42F Component: FaxJob. Category: FaxSys. When generating the class, fail new at
obtaining data domain, soft logic error (software bug).
CF433 CF434 HDD Image Process Error. Destruction of stored jobs on the HDD. It may
CF437 CF43F occur when selecting the keys for calling stored copy or scanner job from a
CF441 CF444 custom box.
CF445 CF451
CF453 Component: CreatePrint. Category: ImageProcess. Entity Error.
CF45F CF453 HDD Image Process Error. Destruction of stored jobs on the HDD. It may
CF454 CF45F occur when selecting the keys for calling stored copy or scanner job from a
CF460 CF463 custom box.
CF46F CF470
CF473 CF47F
CF484 CF487
CF48F CF490
CF493 CF494
CF515
CF526 System Error:
CF528 Component: SVI. Category: LioPanel. Panel data abusion error.
CF530 Component: PJL. Category: RIP. Recovery impossible error: Thread Create
failed.
CF533 Component: PJL. Category: RIP. Entity error: when CLITICAL ERROR
occurred at ME access.
CF533 Component: ReportEventService. Category: RIP. Entity error: when
CLITICAL ERROR occurred at ME access.
CF610 Undefined.
CF610 System Start Error.
CF615 Report Page Generator: USV_RPG_ERR_FACTOR_STREAM (Stream access
error).
CF620 System Error. Error acquiring the event data. Panel detects CF000 as same
error. Unable to Load Files To CF Card.
CF710 Component: IIS. Category: NetApl. Network file written error (inetd).
CF720 Component: IIS. Category: NetApl. Network file written error (services).
CF730 Component: IIS. Category: NetApl. Network file written error (snmpd).
CF750 Component: IIS. Category: NetApl. Network file written error (hostname).
CF760 Component: IIS. Category: NetApl. Network file written error (papd).
CF770 Component: IIS. Category: NetApl. Network file written error (cups).
CF780 Component: IIS. Category: NetApl. Network file written error (dhcclient).
CF790 Component: IIS. Category: NetApl. Network file written error (smb).
CF7A0 Component: IIS. Category: NetApl. Network file written error (netware).
CF7B0 Component: IIS. Category: NetApl. Network file written error (ipfilter).
CF7C0 Component: IIS. Category: NetApl. Network file written error (ethermode).
CF7D0 Component: IIS. Category: NetApl. Network file written error (other).
CFA23 Component: OS_TOOLS. Category: OS. Access error to the Entity at master
data stored area component.
CFA30 Component: OS_TOOLS. Category: OS. AES conversion OPEN error <0x0a>.
CFA43 Component: OS_TOOLS. Category: OS. Access error to the Entity at USB
activation component.
CFB32 Panel Error. Timeout request for start up command. Start command hasn't been
received. Possible destruction of system file in HDD. Cannot enter
maintenance mode. Blue Screen of Death.
CFB33 Component: Panel. Category: KI-Panel. Cut off of the communication with the
controller is detected - waiting to receive: select () OK return, recv() RX data
length 0. Blue back screen. Cannot enter maintenance mode.
CFB34 Component: Panel. Category: KI-Panel. Time out for Response telegraphic
message (could not receive response telegraphic message within a fixed time).
In case on not through httpd, this error occurs (in case it does not become CGI
time out).
CFB35 Component: Panel. Category: KI-Panel. Received abusive command from
controller. At this moment, only the case that unexpected command comes in
when wating for the startup request command.