Академический Документы
Профессиональный Документы
Культура Документы
HH Technology Corp.
500 Cummings Center, Suite 3470
Beverly, MA 01915
CONFIDENTIAL
Note:
The manufacturer is responsible for ensuring that the equipment is designed and constructed in accordance with the
specifications and codes referred to on the requisition and or drawings. Furthermore, the manufacturer is responsible for
ensuring that the design, calculations and thicknesses of material supplied to the manufacturer are for information and
tendering purposes only. The manufacturer shall make his own calculations for which he is fully responsible. The
manufacturer shall ensure that the equipment supplied conforms to all applicable codes and national statutory
regulations, and he shall obtain all necessary approvals from statutory authorities.
The information contained in this document is the property of HH Technology Corp. and is not to be copied or
disclosed to third parties without the prior written consent of HH Technology Corp. nor is it to be misused in any way.
Issue Rev. A
Date 10/29/2015
Prepared by KE
Checked by MD
Approved by UG
Issued by MM
Remarks to Rev. A – Issue For Design
FILTER CAKE VESSEL
ITEM NO. V-4038
No. Required 1
Manufacturer/Supplier Local
Type of Construction Vertical
Service (Batch or Continuous) Batch (filled with 400 to 600 liter of cake slurry 1 to 3
batches per day in a range between 100 and 140 oC)
Location (Indoor/Outdoor) Outdoor ( min / max 5°C / 42°C )
SPECIAL REQUIREMENTS
Page 2 of 6
FILTER CAKE VESSEL
ITEM NO. V-4038
GENERAL NOTES
Page 3 of 6
FILTER CAKE VESSEL
ITEM NO. V-4038
Notes
By Vessel Supplier
Galvanized and Phosphatized
Page 4 of 6
FILTER CAKE VESSEL
ITEM NO. V-4038
NOZZLE TABLE
Nozzle No. N1 N2 N3 N4 N5 N6
Service Demin. Slurry Agitator Condensate Level Level
Water Feed Drain Mount Coil Return Transmitter/ Transmitter/
Gauge Gauge
Top Side Bottom Top Bottom Top Side Bottom
Inlet Outlet Outlet Instr. Instr.
Size 1“ 2“ 2“ 1“ 2“ 2“
Flange Standard ANSI ANSI ANSI ANSI ANSI ANSI
Flange Type Weld Neck Weld Neck Weld Neck Weld Neck Weld Neck Weld Neck
Pressure Rating 150 150 150 150 150 150
Flange Facing Raised Face Raised Face Raised Face Raised Face Raised Face Raised Face
Pipe Dimensions
Blind Flange - - - - - -
Gasket Grooved Grooved Grooved Grooved Grooved Grooved
Gaskets Gaskets Gaskets Gaskets Gaskets Gaskets
Davit Etc. - - - - -
Bolt Standard
Dip Pipe - - - - - -
Inlet
Towards The
Wall
Rev.
Notes:
Page 5 of 6
FILTER CAKE VESSEL
ITEM NO. V-4038
NOZZLE TABLE
Nozzle No. N7 N8 N9 N10 N11 N12
Service Steam Coil Level Switch Slurry Cake
Feed Feed
Side Top Side Bottom Top Inlet
Inlet Instr.
Size 1“ 2“ 8“
Flange Standard ANSI ANSI ANSI
Flange Type Weld Neck Weld Neck Weld Neck
Pressure Rating 150 150 150
Flange Facing Raised Face Raised Face Raised Face
Pipe Dimensions
Blind Flange - - -
Gasket Grooved Grooved Grooved
Gaskets Gaskets Gaskets
Davit Etc. - - -
Bolt Standard
Dip Pipe - -
Rev.
Notes:
Page 6 of 6
HH Technology
Corp.
Engineering & Technology