Академический Документы
Профессиональный Документы
Культура Документы
-- TAG-UL-CCCH-MESSAGE-STOP
-- ASN1STOP
RRCSetupRequest
The RRCSetupRequest message is used to request the establishment of an RRC connection.
Signalling radio bearer: SRB0
RLC-SAP: TM
Direction: UE to Network
RRCSetupRequest message
-- ASN1START
-- TAG-RRCSETUPREQUEST-START
-- TAG-RRCSETUPREQUEST-STOP
-- ASN1STOP
RRCSetup
The RRCSetup message is used to establish SRB1.
Signalling radio bearer: SRB0
RLC-SAP: TM
Direction: Network to UE
RRCSetup message
-- ASN1START
-- TAG-RRCSETUP-START
-- TAG-RRCSETUP-STOP
-- ASN1STOP
– RRCSetupComplete
The RRCSetupComplete message is used to confirm the successful completion of an RRC connection
establishment.
Signalling radio bearer: SRB1
RLC-SAP: AM
Direction: UE to Network
RRCSetupComplete message
-- ASN1START
-- TAG-RRCSETUPCOMPLETE-START
-- TAG-RRCSETUPCOMPLETE-STOP
-- ASN1STOP
The IE BWP-DownlinkDedicated is used to configure the dedicated (UE specific) parameters of a downlink
BWP.
BWP-DownlinkDedicated information element
-- ASN1START
-- TAG-BWP-DOWNLINKDEDICATED-START
-- TAG-BWP-DOWNLINKDEDICATED-STOP
-- ASN1STOP
-- TAG-BWP-DOWNLINKCOMMON-STOP
-- ASN1STOP
The IE BWP-Downlink is used to configure an additional downlink bandwidth part (not for the initial BWP).
BWP-Downlink information element
-- ASN1START
-- TAG-BWP-DOWNLINK-START
-- TAG-BWP-DOWNLINK-STOP
-- ASN1STOP
BWP-Downlink field descriptions
bwp-Id
An identifier for this bandwidth part. Other parts of the RRC configuration use the BWP-Id to associate themselves with a particular bandwidth
part.
The network configures the BWPs with consecutive IDs from 1. The Network does not include the value 0, since value 0 is reserved for the initial
BWP.
For
Suhail For diagrams fig 8 and 7 PDCCH Config part
But in NR, there are lot flexibility for PDCCH control region also and
it is not necessary to span across the complete system bandwidth as
like LTE.
Aggregation Level: It basically tells how many bits are used for
PDCCH transmission. If UE is under bad coverage then n/w may go
with high aggregation level candidate so that UE can reliably decode
the PDCCH. Possible aggregation level in NR is — 1,2,4,8,16
Fig 5: Search Space (SS ID associated with CORESET ID 1) configuration with one
candidate of aggregation level 16
Fig 6: Multiple Search space defined corresponding to one CORESET (Refer Fig 4 here
again)
Fig 7 shows three BWP (each BWP is associated with a BWP ID),
location and width of BWP is defined by two parameter
locationAndBandwidth and offsetToCarrier as shown in Fig
8, refer TS38.214 for exact calculation.
setting , and the first PRB is a PRB offset relative to the PRB indicated by
higher layer parameters offsetToCarrier and subcarrierSpacing
< 38.214-5.1.2.2.2 Downlink resource allocation type 1> defines RIV as follows :
Combining the two specification mentioned above, I would come up with some examples as
shown below. All these examples are based on the assumption that RB_start = 0, BWP takes
up the maximum RB for the specified channel bandwidth and subcarrierspacing = 30 Khz, FR1
CBW max RB Equation RIV Calculation locationAndBandwidth
20 51 (1) 275*(51-1)+0 13750
40 106 (1) 275*(106-1)+0 28875
50 133 (1) 275*(133-1)+0 36300
275*(275-
60 162 (2) 31624
162+1)+(275-1-0)
275*(275-
80 217 (2) 16499
217+1)+(275-1-0)
275*(275-
100 273 (2) 1099
273+1)+(275-1-0)
Following is the table that I calculated for subcarrier spacing = 15 Khz based on the
assumption that RB_start = 0, BWP takes up the maximum RB for the specified channel
bandwidth
max
CBW Equation RIV Calculation locationAndBandwidth
RB
10 52 (1) 275*(52-1)+0 14025
20 106 (1) 275*(106-1)+0 28875
275*(275-
40 216 (2) 216+1)+(275- 16774
1-0)
275*(275-
50 270 (2) 270+1)+(275- 1924
1-0)
Following is the table that I calculated for subcarrier spacing = 120 Khz based on the
assumption that RB_start = 0, BWP takes up the maximum RB for the specified channel
bandwidth
max Equatio RIV locationAndBandwidt
CBW
RB n Calculation h
50 32 (1) 275*(32-1)+0 8525
100 66 (1) 275*(66-1)+0 17875
275*(132-
200 132 (1) 36025
1)+0
275*(275-
400 264 (2) 264+1)+(275 3574
-1-0)