Вы находитесь на странице: 1из 4

REAKNITT ECP

Crosslinking agent for the low formaldehyde and low temperature curing
Character (CHT Comfort -Finish ), easy care finishing of cellulosic fibres and their
blends with synthetic fibres

Chemical Structure Special Modified DMDHEU

Appearance Slight Yellow to yellow clear liquid

Ionic Character -

pH Value of a
10 % Solution 4.0 – 5.0

Specific Weight
at 20 °C Approx. 1.2

Stabilities REAKNITT ECP can be combined with the usual products applied for
easy care finishing. Preliminary tests should be carried out to check the
compatibility especially if antislipping agents or water/oil repellents are
to be used.

This product is sensitive to frost to a certain extent; changes occurring


at low temperatures are reversible when heating and stirring well.

Storability REAKNITT ECP can be stored up to 12 months if stored properly in


sealed original containers. Change in color on storage due to temperature and Sunlight is
susceptible without impairing it’s performance after application.

The above given values are product describing data. Please consult the ‘delivery specification’ for binding product
specifications. Further data about product properties, toxicological, ecological data as well as data relevant to safety can be
found in the safety data sheet.

Properties

Easy care finish of woven or knitted fabric made of cotton, viscose and blends with synthetics.

The following effects are achieved when finishing with REAKNITT ECP:

Energy saving because of Low temperature curing with improved


easy care properties
low formaldehyde values according to LAW 112

Very good hydrolysis stability

excellent fastness of the finishing effects to washing and dry cleaning

soft handle and outstanding abrasion values

REAKNITT ECP total pages 4 page 1


if the product is applied properly, it will be possible to meet Öko-Tex Standard 100 product class II (in direct
contact with skin) with regard to formaldehyde without afterwashing (less than 75 ppm according to
LAW 112). However, the finished textile must in all cases be tested according to the specifications of
Öko-Tex Standard 100.

Application Technique

Diluting Instructions

REAKNITT ECP can be diluted with cold water at any ratio.

Recommendation for Use

Crystalline magnesium chloride (MgCl2 x 6 H2O) is particularly suitable to be used as a catalyst for
REAKNITT ECP. We recommend using 15 - 25% of magnesium chloride cryst. calculated on the quantity of the
resin, but at least 8 g/l. The maximum concentration is limited to 30 g/l.

As alternative to magnesium chloride cryst. we recommend CHT-CATALYST FS which is an already formulated


product. Applying this product the formaldehyde values according to LAW 112 are clearly reduced on the textile
in comparison to the usual catalyst with magnesium chloride. The application concentration is approx.
30 – 35% referring to the quantity of REAKNITT ECP. The minimum/maximum quantity is 15/35 g/l. Anyhow,
preliminary tests are recommended to balance between the easy care effects and the strength loss.

Because the degree of whiteness or the colour shade may be impaired, we recommend carrying out pre trials
when working with white and pastel shades.

The pH value of the ready finishing liquor should be between 4.0 and 6.5. Alkaline fabrics should be adjusted to a
weak acid pH value prior to finishing.

Recipe Proposals

CO: 20 - 50 g/l REAKNITT ECP


CV: 50 - 80 g/l REAKNITT ECP
PES/CO: 20 - 50 g/l REAKNITT ECP
PES/CV: 30 - 70 g/l REAKNITT ECP

REAKNITT ECP total pages 4 page 2


Standard Recipes

Shirting fabric made of cotton (woven fabric)

30.0 - 60.0 g/l REAKNITT ECP


8.0 - 12.0 g/l magnesium chloride cryst.
10.0 - 20.0 g/l POLYAVIN PEN
20.0 - 30.0 g/l TUBINGAL 1112 LIQ
20.0 - 40.0 g/l ARRISTAN 66-L
1.0 - 2.0 g/l KOLLASOL HV
0.5 - 1.0 g/l acetic acid 60%

Liquor pick-up: approx. 60 - 80%


Bath temperature: 20 – 30 °C

Drying: usual conditions


Cure at : 170°C, 30 - 40 s

CHT Comfort Finish ( One Step ) for Co Wovens

120 - 180 g/l REAKNITT ECP


18.0 - 27.0 g/l CHT Catalyst FS
30.0 - 40.0 g/l POLYAVIN PEN
20.0 - 40.0 g/l TUBINGAL 1112 L
20.0 - 30.0 g/l TUBINGAL 66-L
1.0 - 3.0 g/l KOLLASOL HV

Liquor pick-up: approx. 60 - 80 %


Drying and curing: 130 - 150°C air circulation temperature
Curing time: 30 - 40 s at approx. 140°C fabric temperature

CHT Comfort Finish ( 2 Step ) for Co Woven

140 - 200 g/l REAKNITT ECP


24.0 - 40.0 g/l CHT CATALYST BFM
30.0 - 40.0 g/l POLYAVIN PEN
10.0 - 20.0 g/l TUBINGAL SKI-L
20.0 - 30.0 g/l TUBINGAL RGH-L
1.0 - 3.0 g/l KOLLASOL HV

Liquor Pick up: Approx 60 – 80%


Drying and curing: 130 - 150°C air circulation temperature
Curing time: 30 -40 s at approx. 140°C fabric temperature
Rinsing process: approx. 40°C (soft water)
Drying: usual conditions. Top Finish if required

REAKNITT ECP total pages 4 page 3


Top Finish ( Depending upon Handle )

20 - 30 g/l TUBINGAL SKI-L


20 - 30 g/l ARRISTAN 66-L
20 - 30 g/l TUBINGAL RGH-L
1 - 3 g/l KOLLASOL HV

pH value of liquor: 5- 6 preferably adjusted with acetic acid


Liquor Pick up: Approx 60 -80 %
Drying: Usual Conditions

We reserve the right to modify the product and technical leaflet.

Our department for applied technique is always at your service for further information and advice.

Our technical advice and recommendations given verbally, in writing or by trials are believed to be correct. They are neither
binding with regard to possible rights of third parties nor do they exempt you from your task of examining the suitability of our
products for the intended use. We cannot accept any responsibility for application and processing methods which are beyond
our control.

Edition: August 2011


CHT R. BEITLICH GMBH
Postfach 12 80, 72002 Tübingen, Bismarckstraße 102, 72072 Tübingen, Germany
Telephone: 07071/154-0, Fax: 07071/154-290, Email: info@cht.com, Homepage: www.cht.com

REAKNITT ECP total pages 4 page 4

Вам также может понравиться