Академический Документы
Профессиональный Документы
Культура Документы
The following are common dimensions for the 'R' series tools. Check your specific tools - as these can
vary from different suppliers.
1.188 15174 1.094 1.422 JUC 1 1/2 RB 1.430 1.265 40RB14 1.188
1.188 15194 1.844 1.422 JUS 1 1/2 RS 1.430 1.797 40RS5 1.188
1 1/2 RJ 1.430 2.547 40RJ5 1.188
1 1/2 SB 1.437 0.688 40SB3 1.188
1.188 15154 1.094 1.422 JDC 1 1/2 SB 1.437 1.297 40SB6 1.188
1.188 15166 1.844 1.422 JDS 1 1/2 SS 1.430 1.780 40SS3 1.188
1 1/2 SM 1.380 1.578 40SM4 0.875
1.750 15178 1.313 2.250 JUC 2 1/2 RB 2.180 1.203 40RB18 1.750
1.750 15198 2.188 2.250 JUS 2 1/2 RS 2.180 1.984 40RS7 1.750
2 1/2 RJ 2.180 2.547 40RJ2 1.750
1.750 15158 1.313 2.250 JDC 2 1/2 SB 2.180 1.281 40SB2 1.750
1.750 15170 2.188 2.250 JDS 2 1/2 SS 2.180 2.000 40SS2 1.750
In general, Camco tools are a larger OD then the equivalent Otis tools of the same nominal size.
However, Otis tool dogs expand outside the skirt OD when sheared.
3
/4" 0.750" 0.740" 0.630" 0.620"
A 0.440”
GR TOOL
Training
Consultants
The following are the commonly used 'G' series tools (R nipple bore dimensions shown in blue)
Check your specific tools - as these can vary from different suppliers.
3 2.750" 40GR27500 40GS27500 40GU31200 2.31 2.72 1 1/16 -10 UNS 2.313
4 3.125 40GR31200 40GS31202 40GU31200 2.62 3.12 1 1/16 -10 UNS 2.313
4 1/2 3.688" 40GR36800 40GS36804 40GU31200 3.12 3.62 1 1/16 -10 UNS 2.313
5 4.562" 40GR45600 40GS45600 40GU45600 4.00 4.50 1 1/16 -10 UNS 3.125
6 5.625" 40GR56210 40GS56210 40GU56210 4.75 5.56 1 1/16 -10 UNS 3.125
7 5.963" 40GR56210 40GS56210 40GU56210 5.38 5.88 1 1/16 -10 UNS 3.125
7.05 7.050" 40GR70500 40GS70500 40GU70500 5.88 6.55 1 9/16 -10 UNS 5.250
8.125 8.125" 40GR81201 40GS81201 40GU81201 7.12 8.02 1 9/16 -10 UNS 5.250
9.5 9.50" 40GR95000 40GS95010 40GU95000 8.375 9.265 1 9/16 -10 UNS 5.250
Usually of a relatively small diameter as there is an increased shear area over radial types.
Metric equivalents : 3/16" = 4.75 mm : ¼" = 6.35 mm : 5/16" = 7.92 mm, 3/8" = 9.525 mm
Areas (in2): 1
/8” : 0.0122 3
/16” : 0.0274 1
/4” : 0.0490 5
/16” : 0.0767 3/8” : 0.1103
Shear force per side - double this value for radial shear pins
It work hardens and may not shear. Check with a magnet to identify stainless steel from mild steel if
in doubt. Most types of stainless steel are non-magnetic. (but not all!)
If you have access to Otis shear pin part numbers from old documentation they can be very useful.
RB/RS SB/SS
Nom Size Shear Pin # Dia" Length" Shear Pin # Dia" Length"
2" 9P51406 5
/16" 1.406" (1 13/32") 9P41625 1/4" 1.625" ( 1 5/8")
2 1/2" 9P51781 5/16" 1.406" (1 25/32") 9P41875 1/4" 1.875" ( 1 7/8")
3" 9P62375 3
/8" 2.375 " (2 3/8") 9P52625 5/16" 2.625" (2 5/8")
3 1/2" 9P62375 3/8" 2.375 " (2 3/8") 9P52625 5/16" 2.625" (2 5/8")
4" 9P62375 3
/8" 2.375 " (2 3/8") 9P62625 3/8" 2.625" (2 5/8")
GS GU (GR Adapter)
Nom Lock" Shear Pin # Dia" Length" Shear Pin # Dia" Length"
1.875" 9P41625 1
/4" 1.625 ( 1 5/8") 9P51688 5
/16" 1.688" (1 11/16")
2.313" 9P42062 1
/4" 2.062 ( 2 1/16") 9P52000 5
/16" 2.0"
2.750" 9P42500 1
/4" 2.5" ( 2 1/2") 9P62500 3
/8" 2.5" (2 1/2")
2.813"
3.125" 9P52870 5
/16" 2.875 ( 2 7/8") 9P62500 3
/8 " 6.25" (6 1/4")
3.68" 9P53250 5
/16" 3.25 ( 3 1/4") 9P62500 3
/8 " 6.25" (6 1/4")
3.81
4.562" 9P54120 5
/16" 4.12 ( 4 1/8") 9P53250 5
/16" 3.25" (3 1/4")