Академический Документы
Профессиональный Документы
Культура Документы
COLOR TV
WARNING
This service information is designed for experienced repair technicians only and is not designed for use by the general public. It does
not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to service a product. Products
powered b electricity should be serviced or repaired only by experienced professional technicians. Any attempt to service or repair the
product deal with in this service information by anyone else could result in serious injury or death.
1
CONTENTS
Table of contents………………..................…………………………….2
1. General Information…………...............…………………………..4
1-1. General Guidelines...…………………………………………………..4
1-2. Important notice………………………………………………………...4
1-3. How to read this Service Manual……………………………………..5
2. Specifications……………………………………………....................6
2
6. Operation Instructions …………………………........................19
3
1. General Information
1-1 General Guidelines
When servicing, observe the original lead dress. If a short circuit is found, replace all parts which
have been overheated or damaged by the short circuit.
After servicing, see to it that all the protective devices such as insulation barriers, insulation papers
shields are properly installed.
After servicing, make the following leakage current checks to prevent the customer from being
exposed to shock hazards.
1) Leakage Current Cold Check
2) Leakage Current Hot Check
3)Prevention of Electro Static Discharge(ESD)to Electrostatically Sensitive
This symbol indicates that there are important operating and maintenance
instructions in the literture accompanying the appliance
1-2-2. Be careful to the electrical shock
To prevent damage which might result in electric shock or fire, do not expose this TV set to rain or
excessive moisture. This TV must not be exposed to dripping or splashing water, and objects
Filled with liquid, such as vases, must not be place on top of or above the TV
1-2-3. Electro static discharge (ESD)
Some semiconductor (solid state) devices can be damaged easily by static electricity. Such
Components commonly are called Electrostatically Sensitive (ES) Devices. The following
tech-niquesshouldbeusedtohelpreducetheincidenceofcomponentdamagecausedbyelectro
Static discharge (ESD).
1-2-4. About lead free solder (PbF)
This product is manufactured using lead-free solder as a part of a movement within the consum-er
products industry at large to be environmentally responsible. Lead-free solder must be used in the
servicing and repair of this product.
1-2-5. Use the genewing parts (specified parts)
Special parts which have purposes of fire retardant (resistors),high-quality sound (capacitors), low
noise(resistors), etc. are used.
When replacing any of components, be sure to use only manufacture's specified parts shown in
the parts list.
Safety Component
● Components identified by mark have special characteristics important for safety.
4
1-2-6. Safety Check after Repairment
Confirm that the screws ,parts and wiring which were removed in order to service are put in the
original positions, or whether there are the portions which are deteriorated around the serviced
places serviced or not. Check the insulation between the antenna terminal or external metal and
Note:
A “note” provides information that is not indispensable, but may nevertheless be valuable to the
reader, such as tips and tricks.
Caution:
A “caution” is used when there is danger that the reader, through incorrect manipulation,
may damage equipment, loose data, get an unexpected result or has to restart(part of)
a procedure.
Warning:
A “warning” is used when there is danger of personal injury.
5
Reference:
A “reference” guides the reader to other places in this binder or in this manual, where
he/she will find additional information on a specific topic.
2. Specifications
10.2KG(withstand)
796*233*582
(with stand
870*267*657
6
3. Location of Controls and Components
3-1 Board Location
CON2 CON28
CON17
CN5
7
3-2-1 Function Description:
Main Board:
Process signal which incept from exterior equipment,then translate into signal that panel can
display.
3-2-2 Connector definition
8
CON17
Pin number Signal name
1 L+
2 L-
3 R-
4 R+
CN2
CN2
PIN NUMBER DESIGNATION
1 12V
2 12V
3 GND
4 GND
5 5VSTB
6 GND
7 STN
8 SEL
9 V-IPWM
10 BL-ON
11 V-EPWM
9
3-4. LCD Panel
3-4-1 Connector definition
AU(T315XW02 VP)
4-1. L32R1
11
4-1-1 Remove the Pedestal
① Lay down the unit so that rear ① Remove the four screws indicated
cover faces upward on the figure above by
② Remove the five screws from the rear ② Disconnected the coupler CON28、
cover indicated with CON2、CON17、CN5
③ Then remove the pedestal ③ Remove the Main board
4-1-2 Remove the Back Cover 4-1-4 Remove the power module
12
① Remove the four screws ① Remove the two screws indicated on
indicated on the figure above by the figure above by
② Then remove the power module ② Disconnected the coupler CN1
③ Remove the Keypad Assembly
4-1-5 Remove the speaker
13
5. Installation Instructions
Accessories
Accessories
MUTE STILL
ABC@ DEF
P.STD S.STD
CH+
CH-
H.LOCK
outdoor
antenna
(not supply)
Antenna input
75 standard
coaxial type ANT IN
Plug
Antenna adapter (additional purchase)
(not supply)
Note
* It is recommended that you'd better use 75 coaxial cable to remove the
disturbance caused by airwave.
* Don't bind antenna cable and electric wire together.
14
To improve picture quality in a poor signal area, purchase
and install a signal amplifier.
If the antenna needs to be split for two Tv`s, install a 2-
WaySignal Splitter in the connections.
If the antenna is not installed properly, contact your dealer
for assistance.
NOTE: All cables shown are not included with the TV.
VCR Connection
- To avoid picture noise (interference), leave an adequate distance between the VCR and TV.
Connection Option 1
Set VCR output switch to channel 3 or 4 and
then tune the TV to the same channel number.
Connection Option 2
1 . Connect the audio and video cables from the
VCR's output jacks to the TV input jacks, as
ANT IN
shown in the figure.
When connecting the TV to VCR, match the
jack colors (Video = yellow, Audio Left = white,
HDMI2 IN
and Audio Right = red).
CONMPENT IN
L R
2 . Insert a video tape into the VCR and press
PLAY on the VCR. (Refer to the VCR owner`s
manual.)
15
DVD Setup
How to connect
1. Connect the DVD video outputs (Y, Pb/Cb,
Pr/Cr) to the COMPONENT (Y, Pb/Cb, Pr/Cr)
ANT IN
input jacks on the TV and connect the DVD
audio outputs to the AUDIO jacks on the TV,
as shown in the figure.
HDMI2 IN
2. If your DVD only has an S-Video output
CONMPENT IN
VGA/DTV
jack, connect this to the S-VIDEO input Y Pb/Cb Pr/Cr L-AUDIO-R AUDIO
VGA IN
on the TV and Connect the DVD audio VGA
AV OUT
Av1 IN
as shown in the figure.
VIDEO1 L-AUDIO-R S-VIDEO VIDEO L-AUDIO-R
How to use
1. Turn on the DVD player, insert a DVD.
2. Use the TV/AV button on the remote
control to select S-VIDEO or YPbPr/YCbCr
mode.
3. Press Play button on external equipment
for program play. or
4. Refer to the DVD player's manual for
operating instructions. DVD
ANT IN
-To watch digitally broadcast programs,
purchase and connect a digital set-top
box.
HDMI2 IN
How to connect
CONMPENT IN
VGA/DTV
Y Pb/Cb Pr/Cr L-AUDIO-R AUDIO
VGA IN
How to use
1. Turn on the digital set-top box.
(Refer to the owner`s manual for the digital set-top box.)
2. Use TV/AV on the remote control to select PC or HDMI
(Y, Pb/Cb, Pr/Cr) mode.
3. Press Play button on external equipment for program play.
16
PC Setup
How to connect
1. Use the TV`s PC IN port for video connections.
ANT IN
2. Then, make the corresponding audio
connection. If using a sound card, adjust the
HDMI2 IN
PC sound as required.
CONMPENT IN
VGA/DTV
AUDIO
How to use
Y Pb/Cb Pr/Cr L-AUDIO-R
VGA IN
VGA
1. Turn on the PC and the TV.
2. Turn on the display by pressing the POWER
AV OUT
Av1 IN
button on the TV's remote control. VIDEO1 L-AUDIO-R S-VIDEO VIDEO L-AUDIO-R
NOTES:
1 Avoid keeping a fixed image on the TV's screen for a long period of Time. The fixed image
may become permanently imprinted on the screen.
2 The synchronization input form for Horizontal and Vertical frequencies is separate.
3 To obtain the best picture, do not play the USB, YPbPr, HDMI or VGA source at the same
time.
VGA/DTV
Y Pb/Cb Pr/Cr L-AUDIO-R AUDIO
TV or monitor for further details regarding that
VGA IN
VGA
device`s input settings.
AV OUT
Av1 IN
17
Connecting Headphones
You can connect a set of headphones to your set if you wish to watch a
TV programme without disturbing the other people in the room.
L - AUDIO -R
Note
Prolonged use of headphones at a high volume
may damage your hearing.
You will not receive sound from the speakers
when you connect headphones to the system.
Power source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for
AC Outlet
Wider Hole operation on AC. Insert the AC cord plug into
and Blade a standard polarized AC outlet.
NOTES:
Never connect the AC line cord plug to other
than the specified voltage. Use the attached power
cord only.
If the polarized AC cord does not fit into a non-
polarized AC outlet, do not attempt to file or cut
the blade. It is the user`s responsibility to have
an electrician replace the obsolete outlet.
If you cause a static discharge when touching
the unit and the unit fails to function, simply
unplug the unit from the AC outlet and plug it
Polarized AC Cord Plug back in. The unit should return to normal operation.
Polarized AC Cord Plug.
18
6. Operation Instructions
Basal information
Side
Side AV
L - AUDIO -R
TV/AV
1
MENU
2 Left audio input
VOL+
3
VIDEO 2
VOL- Video input
CH+
4
CH-
Earphone jack
POWER 5
HDMI 1
HDMI input
1. TV/AV button
2. MENU button
3. VOL+/- : Volume decrease/increase,adjusting the menu
4. CH+/- : Channel number decrease/ increase
5. Power button
5
HDMI2 IN
6
CONMPENT IN
VGA/DTV
Y Pb/Cb Pr/Cr L-AUDIO-R AUDIO
VGA IN
1 VGA
7
AV OUT
Av1 IN
2 3 4
1. Component Input
Connect a component video/audiodevice to these jacks
2.AV1 Input
Connect audio/video out from an audio/video device to these jacks
3. S-Video Input
Connect S-Video out from a S-Video device to these jacks
4. Video/Audio output terminal
Connect ordinary video/audio or other appliance audio input terminals
5. Antenna Input
Connect cable or antenna signals to the TV, either directly or through your cable box
6. HDMI Input
Connnect a signal to HDMI
7.VGA Input
Connect the monitor output connector from a PC to the jack
19
VIDEO INPUT&OUTPUT MODULE
AUDIO OUT MODULE
HDMI1
DDR SDRAM(128M,16BIT)
HDMI2
ADDR DATA
VGA DVIRX0
AUOUTR/L3 SCART1 OUT
YPbPr1 DVIRX1 GAIN
330
R1,G1,B1,Hs,Vs
DVB(option) (option)
R2,G2,B2 AUOUTR/L2 SCART2 OUT
GAIN
YPbPr2
R0,G0,B0 AV OUT(FOR CHINA)
SCART1OUT OP
SCART1/AV1 CVBS2 AUOUTR/L0 HEADPHONE
OP
AUOUTR/L1 TFA9810T
CVBS3 SPEAKER
Y0,C0
SCART2 SCART2OUT CVBSOUT
SIF0
TV(RF)+9886 Panel
24V
P0WER
VGA AUDIO R/L AUR/L0 5VSTB/3.3V/1.8V/2.5V
I2C EEPROM
SCART2/SUB AV AUDIO R/L AUR/L3
AUMONO SPI FLASH
AV2 AUDIO R/L
4052
R/L
USB USB
YPBPR2 AUDIO
R/L
CARD READER
DVB AUDIO CARD READER
AUDIO IN MODULE
21
+12V Q41 +9V
3 3904 2
LCD Power
R154 L5 VPANEL_IN U2
NC/0 +9V for 74HC4052 SWITCH AUDIO NC/600(4.5X3.2) IRF7314 VCC-Panel
+12V L2 1 8
1
NC/600(4.5X3.2) S1 D1
R2 2 G1 D1 7
C147
0.1uF
R157 D134 CA14 +5V_Pnl L6 100K 3 6
220 600(4.5X3.2) C1 C2 S2 D2
9V 4 G2 D2 5
100uF/16V L27 C6
600(4.5X3.2) 0.1uF 0.1uF
5Vstb CA21 2.2uF
100uF/16V
R10 R15 10K R6 4.7K R3 10K
3
10K Q2 Q1
2 ON_PANEL ON_PANEL R5 1 1
4.7K C15
3904
2
0.1uF 3904
5Vstb
SAMSUNG panel 0~3.3V R34=10K
LG/CMO/AU panel 0~5V,R34 NC
WARNING !!! R9 R12
R444 R18
PWM2 DUTY MUST BE 0x30(CANN'T >0x40,BK0_C7=0x30), 1K +5V
or will destroy Q44!!!!!!!!!!!!!!! NC 220 CON2
10K R13 R11 0 4 5V
3
4.7K
Vcc3.3for MST6X89CL R21 0 Q3 BL-ON/OFF
3 GND
Vcc3.3for MST6X89CL 2.5V for MST6X89CL 1 2 BRI_ON/OFF
3
3904
analog Q5 Q4 R14 1K BL-ADJ_IN 1 BRI_ADJ
3
analog and DDRAM 2 ON_PBACK ON_PBACKR17 NC
1 R19 0 R72
2
PWM0 NC(3904) 1 R34 C14 NC CON4_2.0
PWM0
2.2uF
2
4
4
R16 4.7K 3904
2
NC/10K BL-ADJ_OUT
Pin99, Pin165,
ADJ
OUT
ADJ
OUT
U5 +3.3V for U8 BL-ADJ_OUT
IN
IN
Pin183, Pin194, BL-ADJ_OUT 2
AMS1117-3.3 Pin207, Pin221, AMS1117-2.5 BL-ADJ_IN
VDDP BL-ADJ_IN
1
3
Pin235, R75 0
+3.3Vstb VDDP 60mA +2.5VM
5Vstb L12 FB L17 FB 5Vstb L50 NC R74 NC L11 600(4.5X3.2)
+5V L13 FB R73 +5V 2
C20 C359 C21 C360 C22 C361 C357 C61 C66 C67 C69 C65 C68 C70 C31 C379 C24 C374 C25 C375 1 CN6
CON4_2.5
0.1uF 10uF 0.1uF 10uF 0.1uF 10uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 10uF 0.1uF 10uF 0.1uF 10uF
0
USB Power
Vcc3.3for MST6X89CL
analog
+3.3AVDD for
4
AVDDA
Pin14, Pin39, Pin58,Pin254 2.5V for DDRAM
ADJ
OUT
U6 D6
Vcc 1.26V for MST6X89CL
IN
3
0.1uF 10uF 0.1uF 10uF 0.1uF 10uF C16
R23 10nF
12K R24 CA9 C381
CA8 1 D8 +
+ BST 1N5822 C32
4 EN
C17 220uF/16V 10uF0.1uF
0.1uF 100uF/16V 1.5K_1%
+3.3AVDD +3.3V for R25
8.2K
for AVDD_SIF VDD_MPLL +2.5V_DMQ R86 110_1%
AVDD_SIF Pin63 +2.5VM
+3.3AVDD +3.3Vstb AVDD_MPLL 10mA L25 FB 2 3 R28 2.7K_1%
L19 FB L24 FB C377 C63 GND FB
60mA
2
10nF
0.81*(1+Rup/Rdown)=1.26V---Rup=1.5K, Rdown=2.7K
VCC-1.26V VDDC
+3.3AVDD for L8 FB
+2.5V for MST6X89CL C380 C26 C27 C28 C29 C30 Pin99, Pin146, Pin182,
3.3V for AVDD_AU Pin195, Pin242
Pin70 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
AVDDPLL2 Pin136 AVDD_AU
AVDD_MemPLL +3.3AVDD 30mA +2.5VM +2.5MVDD 30mA
+3.3AVDD L18 NC 4mA L22 FB L16 FB
+3.3Vstb L49 FB C373 C51 C378 C35 C36 C37 C38 C39
C371 C47 Pin108, Pin114,
10uF 0.1uF 10uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF Pin119, Pin135, P147
10uF 0.1uF
22
5Vstb
R102 NC/4.7K
VDDP R104 4.7K
R475 C306 R470R471
3
R26 2 0.1uF
D54 CA110 U43
BAV99 1 8 4.7K 4.7K 4.7K
AVDDA +3.3AVDD 47uF/16V A0 VCC WP_EEP
2 A1 WP 7
2
10K 3 6 R308 100 I2C_SCL
1
R170 1K1 Q14 A2 SCL R309 100 I2C_SDA
4 GND SDA 5
3906 C239 47pF
R234R235 SYS_RST R27 1K 24C64 C236 47pF
3
5Vstb
R172 C263 C150 R158 4.7K
27pF CL=20pf of XTAL AVDD_AU AVDD_MemPLL R103 NC/4.7K
10K 10K C206 1nF AVDDA VDDC VDDP +2.5MVDD R473 4.7K
2
Y1 R446 AVDD_SIF AVDD_MPLL R159 NC/4.7K
HDMI1_HPDCTRL 10uF 3 R214 NC/4.7K
10K 12MHZ 1M R233 NC/4.7K R484
HDMI2_HPDCTRL C356 C313
1
27pF U21 0.1uF
1 8
250
249
248
254
101
149
185
193
240
165
183
194
207
221
235
108
114
119
135
147
136
251
187
188
189
190
A0 VCC 4.7K CON33
70
63
14
39
58
99
98
97
96
95
94
93
92
91
90
89
2 A1 WP 7
3 6 R358 100I2C_SCL
A2 SCL R359 100I2C_SDA
4 5 1
XIN
XOUT
HWRESET
AVDD_AU
AVDD_SIF
VDDM
VDDM
VDDM
VDDM
AVDD_DVI
AVDD_DVI
AVDD_ADC
AVDD_ADC
VDDC
VDDC
VDDC
VDDC
VDDC
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDP
VDDM
AVDD_MEMPLL
AVDD_MPLL
GPIOF[9]
GPIOF[8]
GPIOF[7]
GPIOF[6]
GPIOF[5]
GPIOF[4]
GPIOF[3]
GPIOF[2]
GPIOF[1]
GPIOF[0]
OTG_VBUS
USB_DM
USB_DP
OTG_CID
TX1CLK- AVDDA TX1CLK- GND SDA WP_KEY
TX1CLK- 9 RXACKN 2
TX1CLK+ TX1CLK+ TX1CLK+ 10 24C04/24C128 C240 47pF 3
B1_TX0- B1_TX0- RXACKP C237 47pF
B1_TX0- 12 RXA0N 4
B1_TX0+ B1_TX0+ R454 B1_TX0+ 13 If 24C04,R214&R233 should be NC;
G1_TX1- G1_TX1- RXA0P If 24C128, R158&R103 should be NC. CON4-2.0
G1_TX1- 15 RXA1N
G1_TX1+ G1_TX1+ 16 247 AU2SD0 FOR I2S OUT +3.3Vstb
G1_TX1+ RXA1P DI[13]
R1_TX2- R1_TX2- 18 246 AU2SCK
R1_TX2-
R1_TX2+ 390_1% R1_TX2+ 19
RXA2N DI[12]
245 AU2WS BK9_37[2]=0 C251
R1_TX2+
HDMI
INPUT
8 6 4 2 8 6 4 2 8 6 4 2
7 5 3 1 7 5 3 1 7 5 3 1
TX2CLK- DDCDA_CK DI[7] AU-SW1
TX2CLK- DI[6] 238GPOA6 AU-SW0
AU-SW0 Q201
R258
1
TX2CLK+ TX2CLK+ TX2CLK- 252 237GPIA5 HP_DET 4.7K
B2_TX0- TX2CLK+ RXBCKN DI[5] HP_DET
B2_TX0- 253 RXBCKP DI[4] 236GPOA4 ON_PANEL
ON_PANEL
B2_TX0+ B2_TX0+ B2_TX0- 255 234GPOA3 RP22 100 ON_PBACK SCL_EXT 2 3 3.3V_SCL
G2_TX1- B2_TX0+ RXB0N DI[3] ON_PBACK
G2_TX1- 256 RXB0P DI[2] 233GPOA2 WP_KEY
G2_TX1+ G2_TX1- +3.3Vstb BSS138LT1
G2_TX1+ 1 RXB1N DI[1] 232GPOA1 WP_EEP
R2_TX2- R2_TX2- G2_TX1+ 2 231GPOA0 PW_CTL C252
R2_TX2+ R2_TX2- RXB1P DI[0] PW_CTL
R2_TX2+ 4 RXB2N IVSYNC/TXD1 230IVSYNC RP38 100 0.1u/25V +3.3Vstb
HDMI2_SDA HDMI2_SDA R2_TX2+ 5 229IHSYNC R268
HDMI2_SCL HDMI2_HPDCTRL 6 RXB2P IHSYNC/RXD1
HDMI2_SCL HPLUGB IDE 228GPOA25 100
HDMI2_HPDCTRL HDMI2_SDA 7 227GPIA24
HDMI2_HPDCTRL HDMI2_SCL DDCDB_DA ICLK R266
8 DDCDB_CK Q202
1
C812 0.1uF 226 LVSYNC 4.7K
C813 C358 0.1uFVCLAMP 26 LVSYNC/GPIOE[0] LHSYNC
VCLAMP LVHSYNC/GPIOE[1] 225 TTL
REFP 27 224 LDE SDA_EXT 2 3 3.3V_SDA
REFP LDE/GPIOE[2]
C814
0.1uF
NC REFM 28 REFM LCK/GPIOE[3] 223 LCK Interface BSS138LT1
C815 0.1uFVCOM3 33 220 RXO0-
C816 0.1uFVCOM2 VCOM3 LVB0M RXO0+
35 VCOM2 LVB0P 219
SCB+ SCB+ C203 47nF BIN0P RXO1- CON8
SCB+
SCG+ SCG+ SCG+ C202 47nF GIN0P
34
36
BIN0P U41 LVB1M 218
217 RXO1+
SC_SOG SC_SOG 1nF SOGIN0 GIN0P LVB1P RXO2-
VGA Y PB PR
SCR+ SCR+ SCR+ C201 47nF RIN0P 38 215 RXO2+ RXE0- 3 4 RXE0+
RIN0P LVB2P RXOC- +5V_Pnl RXE1- B0- B0+ RXE1+ +3.3AVDD+5V_Pnl RXO0- RXO0+ +3.3AVDD
41 HSYNC0 LVBCKM 214 5 B1- B1+ 6 1 A0- A0+ 2
42 213 RXOC+ 7 8 RXO1- 3 4 RXO1+
VSYNC0 LVBCKP RXO3- RXE2- GND GND RXE2+ RXO2- A1- A1+ RXO2+
LVB3M 212 9 B2- B2+ 10 5 A2- A2+ 6
HS_RGB HS_RGB HS_RGB 24 211 RXO3+ R491 RXEC- 11 12 RXEC+ R490 R493 RXOC- 7 8 R495
VS_RGB VS_RGB HSYNC1 LVB3P RXO4- 10K/NC BC- BC+ 10K/NC 10K/NC GND GND RXOC+ 10K/NC
VS_RGB 25 VSYNC1 LVB4M/NC 210 13 GND GND 14 9 AC- AC+ 10
BIN+ BIN+ BIN+ C133 47nF BIN1P 29 209 RXO4+ RXE3- 15 16 RXE3+ RXO3- 11 12 RXO3+
SOG SOG C136 1nF SOGIN1 30 BIN1P LVB4P/NC B3- B3+ RXO4- A3- A3+ RXO4+
SOG SOGIN1 17 GND GND 18 13 A4- A4+ 14
GIN+ GIN+ GIN+ C134 47nF GIN1P 31 206 RXE0- 19 20 15 16
RIN+ RIN+ C135 47nF RIN1P GIN1P LVA0M RXE0+ RXE4- SelectSelect RXE4+ SelectSelect
32 205 21 22
RIN+
43
RIN1P
MST6E89 LVA0P
LVA1M 204
203
RXE1-
RXE1+
R492 3.3V_SDA
NC VCC-Panel
23
25
B4- B4+
3Vsda 3Vscl 24
26
3.3V_SCL R489
NC
R494
NC CON36
R496
NC
VSYNC2 LVA1P GND GND
Y,Pb,Pr
AV3-Vin+ AV3-Vin+ C312 47nF CVBS3 Y0 RP28 RP100X4 MDATA0 BL-ADJ_IN +2.5V_DMC +2.5V_DMQ
AV3-Vin+ 52 CVBS3 MDATA[0] 123 BL-ADJ_IN
AV1-Vin+ AV1-Vin+ C311 47nF CVBS2 MDATA1
8 6 4 2 8 6 4 2 8 6 4 2 8 6 4 2 8 6 4 2
7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1 7 5 3 1
AV1-Vin+ 53 CVBS2 MDATA[1] 122
54 121 MDATA2
R211 47 AV2-Vin- C309 47nF VCOM1 CVBS1 MDATA[2] MDATA3
55 VCOM1 MDATA[3] 120
TV1-Vin+ TV1-Vin+ TV1-Vin+ C308 47nF CVBS0 56 118 RP29 RP100X4 MDATA4 C142 C122 C140 C141 C138 C137 C139 C123
TV1-Vin- TV1-Vin- C214 47nF VCOM0 CVBS0 MDATA[4] MDATA5
TV1-Vin- 57 VCOM0 MDATA[5] 117
CVBSOut2 59 116 MDATA6 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF
CVBSOut CVBSOut CVBSOUT1 MDATA[6] MDATA7
CVBSOut 60 CVBSOUT0 MDATA[7] 115
112 RP30 RP100X4 MDATA8
TV-SIFP C440 0.1uFSIF0P MDATA[8] MDATA9
TV-SIFP 62 SIF0P MDATA[9] 111
64 110 MDATA10
TV-SIFM C441 0.1uFSIFM SIF1P MDATA[10] MDATA11
TV-SIFM 65 SIFM MDATA[11] 109
AUVREF 69 107 RP31 RP100X4 MDATA12
AUVRADP AUVREF MDATA[12] MDATA13 +2.5V_DMC +2.5V_DMQ
68 AUVRADP MDATA[13] 106
AUVRADN 67 104 MDATA14
C436 C435 C213 C437 PC-Lin C332 2.2uFAUL0 AUVRADN MDATA[14] MDATA15 U12
PC-Lin 71 AUL0 MDATA[15] 103
PC-Rin PC-Rin C333 2.2uFAUR0 72 130 RP32 RP33X4 MCLK+ IR-in IR-in
AUDIO
AUR0 MCLK
INPUT
4.7uF 1uF 10uF 0.1uF HD1-Lin HD1-Lin C334 2.2uFAUL1 73 129 MCLK- 1 66
HD1-Rin C335 2.2uFAUR1 AUL1 MCLKZ CKE MDATA15 MVDD VSS MDATA0
HD1-Rin 74 AUR1 MCLKE 128 2 DQ0 DQ15 65
R663 0 C434 0.1uFAUCOM 75 127 MVREF 3 64
AV1-Lin C336 2.2uFAUL2 AUCOM MVREF R449 100 UDQM MDATA14 VDDQ VSSQ MDATA1
AV1-Lin 76 AUL2 UDQM 126 4 DQ1 DQ14 63
AV1-Rin C337 2.2uFAUR2 77 125 R450 100 LDQM MDATA13 5 62 MDATA2 5Vstb+3.3Vstb 5Vstb
AV1-Rin AUR2 LDQM DQ2 DQ13 CN5
MUX-Lin MUX-Lin C338 2.2uFAUL3 78 124 R452 100 DQS0 6 61
MUX-Rin C339 2.2uFAUR3 AUL3 DQS[0] R483 100 DQS1 MDATA12 VSSQ VDDQ MDATA3 R429 R420 R433
MUX-Rin 79 AUR3 DQS[1] 102 7 DQ3 DQ12 60 1
TV1-L/Rin TV1-L/Rin C195 2.2uFAUMONO 80 133 R485 22 RASZ MDATA11 8 59 MDATA4 2
AUMONO RASZ R486 22 CASZ DQ4 DQ11 LED-B
CASZ 137 9 VDDQ VSSQ 58 3
81 138 R487 22 WEZ MDATA10 10 57 MDATA5 LED-R 4
AUOUTL3 WEZ MDATA9 DQ5 DQ10 MDATA6 4.7K 8.2K 8.2K
82 AUOUTR3 11 DQ6 DQ9 56 5
SC2-L R155 100 LINE_OUT_1L 83 131 BA1 12 55 IR-in 6
OUTPUT
SC2-L SC2-R R156 100 LINE_OUT_1R AUOUTL2 BARD[1] BA0 MDATA8 VSSQ VDDQ MDATA7
84 132 13 54 7
AUDIO
SC2-R AMP-L R44 100 DAC_OUT_0L 85 AUOUTR2 BARD[0] RP39 RP100X4 AR11 DQ7 DQ8
AMP-L AUOUTL1 MADR[11] 153 14 NC NC 53 8
AMP-R R42 100 DAC_OUT_0R 86 AR10
8 6 4 2 8 6 4 2 8 6 4 2
7 5 3 1 7 5 3 1 7 5 3 1
AMP-R AUOUTR1 MADR[10] 152 15 VDDQ VSSQ 52 9
PH-L R41 100 DAC_OUT_1L 87 151 AR9 DQS1 16 51 DQS0
PH-L PH-R R40 100 DAC_OUT_1R 88 AUOUTL0/Subwoofer MADR[9] AR8 LDQS UDQS KEY1-in
PH-R AUOUTR0 MADR[8] 150 17 NC NC 50
146 RP40 RP100X4 AR7 18 49 FSVREF KEY0-in CON5_2.0
C188R352C172R293C154R272C176R351C152R153
C153R149 MADR[7] AR6 MVDD VREF D132 D133 D131
177 DDCR_DA MADR[6] 145 19 NC VSS 48
2
178 144 AR5 UDQM 20 47 LDQM
DDCR_CK MADR[5] LDM UDM
PWM0/MCUCFG0
PWM1/MCUCFG1
PWM2/MCUCFG2
PWM3/MCUCFG3
1
MADR[2] AR1 RAS CKE INPAQ_VPORT INPAQ_VPORT
171 140 24 43
GPIOB[6]
173 26 41
WRZ
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
SDO
SCK
RDZ
IRIN
SCZ
ALE
INT
7 5 3 1
182
SCK167
SDI 168
SCZ169
SDO170
3
11
17
40
61
66
100
105
113
134
148
166
184
208
222
241
257
186
154
155
156
157
158
159
160
161
162
163
164
181
R453
C387
RP37 RP100X4 33 34
8 6 4 2 MVDD VSS
100pF C366
100pF C367
P42 LED-R
8 6 4 2 8 6 4 2
7 5 3 1 7 5 3 1
P41
P40 HY5DU281622ET-4
5Vstb
100pF
P17
RP36 RP0X4 SCL_RES
NC/10pF
7 5 3 1
RP100X4
100
SPI_CZ
HDCEC
IR-in
SPI_DI
3
R460 R425 R442 R464 C352 C363 10K Q46
R384
R394
2
5Vstb 10K NC 10K NC U42
CON38 PWM0 0.1uF 1nF
4.7K 4.7K PWM1 PWM0 SPI_CZ 10K 10K 1nF 0.1uF
1 1 CE# VDD 8
2 100 R367 RXD0 R438 R432 R435 R436
3 100 R368 TXD0 PWM3 SPI_DO 2 7
R423 R462 R469 SO HOLD#
4
5 PWM1 R52 33K WP_FLASH3 6 SPI_CK
C364 WP# SCK 4.7K 4.7K 4.7K SCL_RES
4.7K
CON5_2.0 4 5 SPI_DI SDA_RES
NC 10K NC 0.1uF VSS SI SCL_EXT
SDA_EXT
EN25F80-100/PMC25L080
23
P1 1 HDMI1-RX2+ R310 10 R1_TX2+ R1_TX2+ 2
DATA2+ HDMI1-RX2- R311 10 R1_TX2-
DATA2 SHIELD 2 R1_TX2- 2
3 HDMI1-RX1+ R312 10 G1_TX1+ G1_TX1+ 2
DATA2- HDMI1-RX1- R313 10 G1_TX1-
20 GND1 DATA1+ 4 G1_TX1- 2
5 HDMI1-RX0+ R314 10 B1_TX0+ B1_TX0+ 2
DATA1 SHIELD HDMI1-RX0- R315 10 B1_TX0-
21 GND2 DAT1A- 6 B1_TX0- 2
7 HDMI1-RXC+ R696 10 TX1CLK+ TX1CLK+ 2
DATA0+ HDMI1-RXC- R697 10 TX1CLK-
22 DATA0
GND3 SHIELD 8 TX1CLK- 2
9 D98 D11 D12 D13 D14 D15 D16 D17 D18
DATA0-
2
23 GND4 CLK+ 10
CLK SHIELD 11
24 GND5 CLK- 12
13 CEC
1
CEC INPAQ_VPORTINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGA
NC 14
SCL 15
16 HDMI1/5V +5V
24C02=>EDID code must
SDA
DDC/CEC GND 17
D19
be upto 256byte space,
18 1
+5V POWER
HOT PLUG 19 R78 for HDMI interface.
3
HDMI_J
BAT54C
R79 R80 R81 For CEC Leakage Protect
U46 supplier must be 3.3V,When
2
1K U14 C124 power of,U46 supplier must be 0V+3.3AVDD
HDMI1-HPD 8 1
NC/4.7K 7 VCC NC 0.1uF CECR664 0 U46
WP NC 2
HDMI1-DDC-SCL 10K 10K R82 100 6 3 R665 1 6 R666
HDMI1-DDC-SDA R83 100 SCL NC A V+
5 SDA GND 4
2 GND NC 5
SOT C 3
2
D100 Q8 D20 D21 24C02
2
R85 4.7K HDCEC NC/1K 3 4 10K
HDCEC B SEL FSA2156
2 E 23
HDMI1_SCL
HDMI1_SCL 2
5.6V 5.6V HDMI1_SDA R667 27K
1 B
1 HDMI1_SDA 2
1
INPAQ_VPORT 3904
1K HDMI1_HPDCTRL
HDMI1_HPDCTRL 2 Must be 27K
2
23 GND4 CLK+ 10
CLK SHIELD 11
24 GND5 CLK- 12
13 CEC
1
1
CEC INPAQ_VPORTINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGAINPAQ_EGA
NC 14
SCL 15
16 HDMI2/5V +5V
24C02=>EDID code must
SDA
DDC/CEC GND 17 be upto 256byte space,
18 1 D34
+5V POWER
HOT PLUG 19 R163 for HDMI interface.
3
HDMI_J R93 R138 R152
2 BAT54C
1K U20 C132
HDMI2-HPD 8 1
NC/4.7K 7 VCC NC 0.1uF
WP NC 2
HDMI2-DDC-SCL 10K 10K R94 100 6 3
HDMI2-DDC-SDA R161 100 SCL NC
5 SDA GND 4
SOT C 3
R160 4.7K
2 E 23
HDMI2_SCL
HDMI2_SCL 2
5.6V 5.6V HDMI2_SDA
1 B
HDMI2_SDA 2
1
INPAQ_VPORT 3904
R137 1K HDMI2_HPDCTRL
HDMI2_HPDCTRL 2
24
D23 VGA-DDC-5V
4 PC-L
P2 2 PC-L 1K PC-Lin PC-Lin 2 VGA/5V 1
1 R396
3 PC-R 3
5 PC-R 1K PC-Rin PC-Rin 2
6 D86 D87
87 R397 +5V 2
2D
7 C260 R294 C259 R295
PHONEJACK
BAT54C
TXD0
1
INPAQ_VPORT 560pF 22K 560pF 22K D99 D101 RXD0
2
INPAQ_VPORT
INPAQ_VPORT INPAQ_VPORT
1
P3 VGA/5V
15 5
10
14 4 R113 NC RXD0
RXD0
9
VGA-B+ L38 0 R95 47 BIN+
13 3 BIN+ 2
8 47
12 2 VGA-G+ L39 0 R96 GIN+ GIN+ 2
7
VGA-R+ L40 0 R97 47 RIN+
11 1 RIN+ 2
6
2 D95 D96 D97 R99 R100 R101 R98 470 SOG SOG 2
2
16
17
VGA
75 75 75
1
1
INPAQ_VPORT INPAQ_VPORT
INPAQ_VPORT
R111 NC TXD0
TXD0
5.6V 5.6V
1
VGA-DDC-5V
R112 R109R110
C145
U16 0.1uF
1 8 4.7K 4.7K
NC VCC NC
2 NC VCLK 7
3 6 R114 100 VGA-SCL
NC SCL R115 100 VGA-SDA
4 GND SDA 5
24C02
R116 4.7K
25
+5V
C162
R129
C163
R130
C164
R131
R134
NC/10K
R132
NC
NC
NC
NC/10K
1
75
75
75
INPAQ_VPORT
INPAQ_VPORT INPAQ_VPORT
R133
NC/10K
P5 YPBPR_L/R
7 HD1-L R371 1K HD1-Lin
7 4 4 HD1-Lin 2
6 6 L
5 5
1 1
3 2 HD1-R R372 1K HD1-Rin HD1-Rin 2
3 2
R
D105 D104 R215 R212
2
C200 C198
560pF 560pF
INPAQ_VPORT INPAQ_VPORT 22K 22K
1
26
Note:when SCR+,SCG+,SCB+ as scart RGB
input,R339(net SC_SOG,from AV input)must
be 470ohm,R305must be NC,else SCR+,SCG+,
AV1 Input/output SCB+ as HDTV input, R305(net SC_SOG,from
HDTV input)must be 470ohm,R339 must be NC.
P15
L58
AV1-V R166 47 AV1-Vin+ +9V
7 7
1 AV in D116 0
AV1-Vin+ 2
R190 10K
S-Video1 Input
47K
47K
47K
47K
R168 NC SC_SOG
2 C180 C181 R339 R177 CA15
8 AV1-L
3 L 8
R176
R223
R180
R173
NC/330pF NC/330pF75 L76 100uF/16V
1
SV1-C R222 47 SV1-Cin SV1-Cin 2 10K
4 INPAQ_VPORT D109 0
2
AV1-R R225 U28
5 R 9 9
C207 C826 12 13 MUX-Lin MUX-Lin 2
R374 1K AV1-Lin P12 DIN4_V HD2-Lin C325 2.2uF X0 X
6 AV1-Lin 2 14 X1
D117 NC/330pF NC/330pF AV3-Lin C326 2.2uF 15
1
X2
2
75 11 3 MUX-Rin MUX-Rin 2
C184 R174 INPAQ_VPORT X3 Y
2 C L 3
22K 1 +9V
560pF 7 4 L78 1 16
1
SV1-Y R228 47 SV1-Yin HD2-Rin C329 2.2uF Y0 VCC C320 C323
8 5 SV1-Yin 2 5 Y1 GND 8
INPAQ_VPORT 6 D110 0 AV3-Rin C330 2.2uF 2 6
Y2 INH
2
13 R230 4 7
13 C215 C217 Y3 VEE 0.1uF 10uF
out 10
AV 10 +9V
R373 1K AV1-Rin AV1-Rin 2 +5V
14 D118 NC/330pF NC/330pF SW0 10
1
14 A
2
3
10K 10K
signal is 1Vp-p, so AU-SW0 R179 10K 1 Q20
2 AU-SW0
AV6 L68 FB it must multiply 3904 AV3-Rin R224 NC MUX-Rin
+5V
3
C353 R194 R196
signal by four (GAIN
2
C192 2 AU-SW1 AU-SW1 R183 10K 1 Q35
10uF 0.1uF X 4) for 2Vp-p output 3904
2
Q17 470
2
1 3 15K
Q18
3906 1 C307 10uF CVBSOut CVBSOut 2
3
D119 68
2
C190 R193
INPAQ_VPORT 75
NC/330pF NC/330pF
R195 47 TV1-Vin- TV1-Vin- 2
Scart2_Lout R407 100 C216 2.2uF Scart2_L
D120
2
C519 R204
L66
1nF TV1-L/R TV1-L/Rin
Location 7 TV1-L/R
10K
TV1-L/Rin 2
1
INPAQ_VPORT
10K Near RCA. R200 C256
C520 R205
1nF
1
10K
INPAQ_VPORT
+9V L65 FB
R680C351 C819
10uF 0.1uF
R682
CON24
Q45
3
2 HD2-R R401 10K HD2-Rin
1 47k R683 15k C348 2.2uFSC2-L SC2-L 2
3 HD2-L R386 10K HD2-Lin
1 AV2 3904
2
C293 R304 C294 R303
NC/CON3_2.0 R684 R685
AV3-R R370 1K AV3-Rin
CON23
D112
2
7 ON_USB ON_USB 2 560pF 12K 560pF 12K C193
6 HD2_PBIN R197 47 8.2k
5 HD2_YIN 560pF 22K
4
1
3 HD2_PRIN
2 INPAQ_VPORT
1 IR-in IR-in 2
AV3-L R369 1K AV3-Lin +9V L63 FB
2 D111
NC/CON7_2.0 R686C350 C820
C189 R189
22K 10uF 0.1uF
560pF
1
3
D122 D123 D124 4 D113
2
C827 R219C204 R220C205 R221 R305 470 SC_SOG SC_SOG 2 3 1 47k R689 15k C349 2.2uFSC2-R SC2-R 2
Note:when SCR+,SCG+,SCB+ as scart RGB 2 C185 C186 R187
1 75 3904
2
NC/330pF 75NC/330pF75NC/330pF75 input,R339(net SC_SOG,from AV input)must NC/330pF NC/330pF
1
INPAQ_VPORT CON5_2.0
be 470ohm,R305must be NC,else SCR+,SCG+, R690 R691
INPAQ_VPORT INPAQ_VPORT INPAQ_VPORT
SCB+ as HDTV input, R305(net SC_SOG,from
HDTV input)must be 470ohm,R339 must be NC.
47 8.2k
27
U23 PIN2 connected to PIN1 B/G,DK,I,L
U23 PIN2 connected to GND L' I2C ADDRESS(R263 NC):
+12V R277 100 5V-IF
3
C146 D88 NC/BA277
U22 TUNER_IF 1 Q28
3
2SC2216 Q22
14
15
13
12
AGND
2
10nF 1R382 10K
C221 AGND IF-AGC
GND1
GND4
GND2
GND3
R269
R347 R345 3904 R245 Y2
2
4MHz
75 1.2K 56 10nF C223 CA71
2
NC R247C222 R249 C224 +
R387 0 3 0.1uF 100K
IFout
AGC
SDA
NC1
NC3
NC4
SCL
5VA
5VB
33V
AS 330 1.5nF 0.1uF 47uF/16V
L81 FB 0/BA277 AGND
1
5V-IF D79 U23 C225 C227 C228 R248
1
2
3
4
5
6
7
8
9
10
11
C300 C299 1 IN 22K
C226 IF_TV
R279 NC/0 SAW OUT2 5
220nF 470nF 22pF AGND
L82
10uF 10uF 0.1uF R250 0 IF-AGC 5V-OUT 5V-IF
C229
R251 100SDA_EXT D65 BA277 TV
C231
FB
GND
AGND SCL_EXT 2 4 R253
R252 100 ING OUT1 C303
0.1uF
R255 R273
24
23
22
21
20
19
18
17
16
15
14
13
R241 10nF K9453D 10uF
C230 4.7K NC 100
VPP
CVBS
SIF2
SIF1
REF
OUT2
VPLL
TAGC
AFC
AGND
TOP NC(5)/VAGC(6)
NC
C233 AGND
22pF 22pF
3
NC AGND AGND AGND
1 Q23
AUD_OUT
U25 3904
SIOMAD
AGND C235 K3953D U24
FMPLL
2
DGND
DEEM
OUT1
10nF TDA9885&6 TV1-V TV1-V 6
VIF1
VIF2
SDA
AFD
SCL
1 IN R257
R256 SAW OUT2 5
75
10
11
12
GND
2 4 R259 100 SCL_EXT
SCL_EXT 2
NC ING OUT1 R260 100 SDA_EXT
SDA_EXT 2
TV1-L/R
3
C241 TV1-L/R 6
SIFPOUT TV-SIFP TV-SIFP 2
R261 NC TV-SIFM TV-SIFM 2
AGND C245C246 R264
R262 C243 C244 R263
10nF 10nF470nF NC(2K)
5.6K 390pF 1nF 220
L87 5V-IF
5V and 12V for Tuner 10uH R265 0
AGND
28
CON39
+12V
6VBuf1 +12V 1
L31 2 L29
L10 3 R406 R409 R66 L1
600(4.5X3.2)
600(4.5X3.2)
600(4.5X3.2)
600(4.5X3.2)
CA16 R437 4
100uF/16V C3 10 C74
CON4_2.5 0.1uF 0.1uF
NC NC C84 C81
R414
R415 33K OP_VCC1 100
33K C341 CA17
8
0.1uF
cc
470uF/35V
3 +
1 AMP-Lin C79 C80
AMP-L C340 2.2uF R439 10K OUT1- R37 100K 0.1uF 0.1uF
13
25
24
2 AMP-L 2 -
9
U10
C342
N.C.
VDDA1
VDDA2
VDDP1
VDDP2
4
TL062 R402 AMP-Rin C7 330nF
R67 10K R69 10K FOR 8ohm:L5,L26=22uH,C75,C71,C93,C94=330nF;
L33 22uH
1nF C85 R55 10K C76 220nF 5 4
2 26 OUT1+ 1 2 AMP-Rout+
R455 68K 47K C87 IN1P OUT1P C82 C93
3
220pF 470pF
C479 100pF C86 10K 27
47pF R56 BOOT1P R48 10 330nF
3 IN1M
220pF R47 10 C94
OP_VCC1 29
R54 0 C52 330nF
R68 10K R70 10K BOOT1M C83
U45B 470pF 330nF
8
28 OUT1- 5 4 AMP-Rout-
OUT1+ R71 100K C78 330nF OUT1M
5 + 1 2
7 AMP-Rin 8 C77 220nF
3
AMP-R C343 2.2uF R441 10K CDELAY L32 22uH
2 AMP-R 6 - For 26dB change R5, R14, R17 and TFA9810T C64 CON17
C179 4
TL062
R403
R26 from 100k into 200k. 6 SO/OL STABI1 31 1uF 1
2
1nF * = R35 and R36 need to have the HP_MUTE_AMP7 C72
3
4
ENABLE
R459 68K 47K
same value as the output STABI2 18 1uF
CON2_2.54
C478 100pF impedance of the signal source. 10 DIAG
FOR 8ohm:L27,L28=22uH,C56,C59,C95,C96=680nF;
L30 22uH
OUT2- R59 100K C55 220nF 5 4
cc 11 23 OUT2+ 1 2 AMP-Lout+
R61 10K TEST OUT2P C90 C95
3
AMP-Lin C53 330nF R63 10K 470pF
R57 22
10K BOOT2P R50 10 330nF
C88 15 R49 10 C96
220pF IN2P
6VBuf2 +5V +12V BOOT2M 20
C92 C91
68pF 470pF 330nF
C89 14 21 OUT2- 5 4 AMP-Lout-
CA18 100uF/16V 220pF IN2M OUT2M
1 2
R427 R430 R58 C54 220nF
VSSA1
VSSA2
VSSP1
VSSP2
3
VSSD
VSSD
VSSD
VSSD
0 NC R65 0 C57 330nF
R62 10K R64 10K 10K L28 22uH
R410 33K R411 33K OP_VCC2
C199 CA19
OUT2+ R60 100K
12
16
17
32
30
19
U38A 0.1uF 100uF/16V
8
3 + R76 22
1
2 PH-L PH-L C273 2.2uF R424 10K 2 -
5Vstb
C194 R404
4
PT2308 R428
1nF
47K P8 Q27
R421 33K CA92 100uF/16V PH-Lout 3 10K R287 3904
5 2 AMP-MUTE AMP-MUTE 10K 1
C464 100pF CA93 100uF/16V PH-Rout B R289 100
2 SOT
C 3
4 2 E 23
1 5Vstb
OP_VCC2 6 +5V
R301R302 7 R282 10K HP_MUTE_AMP
U38B CON5_2.0 R281
8
D70 D71
5 + R412 R418 1N4148 R330 NC/0
Q25
7 1K 1K 1N4148
2 PH-R PH-R C272 2.2uF R422 10K 6 - 10K 1 B Q26
SOT
C173 R405 10K 10K R283 1K C 3 R284
1K 1
2 E 23 B
4
R329 NC HP_MUTE_AMP
H1 H2 H4 H5 H6 H14
1
1
5 9 5 9 5 9 5 9 5 9 5 9
1
H9
4 8 4 8 4 8 4 8 4 8 4 8 NC
3 7 3 7 3 7 3 7 3 7 3 7
1
H8
2 6 2 6 2 6 2 6 2 6 2 6 NC
NC NC NC NC NC NC
1
H7
29 NC
POWER INPUT
CON28
1 +12V
2 +12V
3
4
5 5Vstb
6
7 STANDBY R337 4.7K 5Vstb
R336 R341
Normal: L
3
CON7_2.0 NC
C 23
Q34
SOT
4.7K
3904 Standby:H
B
R338
PW_CTL
1
4.7K PW_CTL 2,8
+12V U1 +5V
L3
2 VCC OUT 3 5 4
1 2
7 C19
3
EN 10nF
6 COMP 10uH R4
C4 1 3.9K CA3 C9
BST D3 + C382
8 SS
10nF 1N5822
CA1 C12 10uF 0.1uF
+ R8 C18
0.1uF R7 470uF/16V
0.1uF 1.2K
4 GND FB 5
470uF/16V 7.5K
MP1430
Title
Power board
3
+ EN 10nF
6 COMP 10uH R33
0.1uF C5 1 3.9K CA4 C10
470uF/16V BST D4 + C383
8 SS
10nF 1N5822
10uF 0.1uF
5Vstb R35 4.7K R31 C42
0.1uF R32 470uF/16V
R36 4.7K 1.2K
Q31
31 4 5
GND FB
3Q
7.5K
STANDBY R46 NC/4.7K
1
MP1430
NC/3904
2
30
7-2 .Wiring Connection Diagram
31
Press VOL+/- to choose the Source you want in factory mode.
2、ADC ADJ
Choose the AUTOTUNE to adjust the color of PC/YUV source. Automatically.
16 gray bar in PC source and 75% color bar in YUV source
3、PICTURE MODE
Adjust the Brightness and Contrast in every picture mode.
4、SOUND MODE
Adjust the Bass and Treble in every sound mode.
5、COLOR TEMP
Adjust the Gain and Offset of RGB for every Color Temperature.
6、EEPROM ADJUST
No use in the software.
7、NON LINER
Adjust the linear value of Brightness, Contrast, Definition, Chroma, Volumn, Treble and Bass
8、SSC SETING
No use in the software.
9、DIMMER
No use in the software.
10、OTHET OPTION
PW2STD SAVE :The status is memorizable in AC~ power on time
ON: The status is standby in AC~ power on time
OFF: The status is AutoPowerOn in AC~ power on time
TEST PANEL:No use in the software.
SOUND CARRIER:No use in the software.
FAVOURITE PROG: Switch of Favourite Program
USB: No use in the software。
FINE TUNE:Adjust the ADC value for tuner.
PWM ADJ:Adjust the backlight value of LCD panel.
11、E2P INT :Initialization of software(Restart after the initialization)
12、DLC:Dynamic Light Control for brightness.Testing only!
9. Trouble shooting
9-1. Simple check
32
Press Mute button and verify if Mute mode is set.
Switch to otger channel and verify if the same problem
No sound happens.
Press VOL+ button to see of he problem can be solved.
33
Backlight control CON2
if BRI_ON/OFF(5V) then BACKLIGHT ON
State:No sound
First,check cables which connect with PSU,then check as follows
1) Check input voltage as NO picture
2) Check speaker output
First,check speaker anode(+) and cathode(-),confirm speaker short or not.If short ,replace speaker.
Second,check CNC1 with oscillograph,confirm wave output or not.
Power supply for AMP(U10)-L42T1 16.5V,L47T1 12V
34
Part Name Description Phenomena Failure cause
Vertal gray
V Dim
line
Vertical color
V L/D line(light or
TCP dark forever)
Horizontal
H B/D
bar
Horizontal
H Dim
gary line
Horizontal
H L/D line(light or
dark forever)
Failure Mode
Part Name Description Phenomena Failure cause
35
Bright dot dark
Dot Defect Incoming Inspection Standard
dot in pannel
Panel or
Polarizer Bladder in
Polarlzer Bladder between Polarizer and top glass
Bubble Polarizer
Polarizer
Polarizer Scratch Tine or rigidity arose
Scratch
Abnormal
Abnormal Display 1.Chip lose action
Display
2.IC ahort or jointiog bad
Circuit
Bright and dark 3.Pannel and vsc connect bad
Flashing
display alternately
Failure Mode
Part Name Description Phenomena Failure cause
Circuit
FIIcker Crosstalk LCD Vcom imbalance
36
When turn
Mechanlcal Caused by Mechanica noise of backlight
panel,appear
Nolse unit
cacophony
B/L wire
B/L wire damaged Operation abnormal or systemic noise
damaged
B/L wire
Without backlight Operation abnormal or systemic noise
open
B/L shut B/L shutdown in Short bitween lamp housing and wire, Because
down sometime consume power too much
F/M in
B/L ,white,balck
F/M F/M in B/L unit
Rotundity or
wirelike
Failure Mode
Part Name Description Phenomena Failure cause
Brightness at
Light bottom of LCM
B/L unit badness
leakage brighter than
normal
Mechanlcal
B/L brightness
or B/L Uniformity Sheet in B/L unit is uneven
asymmetric
37