Академический Документы
Профессиональный Документы
Культура Документы
Product Description
Issue 05
Date 2014-06-18
and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.
All other trademarks and trade names mentioned in this document are the property of their respective
holders.
Notice
The purchased products, services and features are stipulated by the contract made between Huawei and
the customer. All or part of the products, services and features described in this document may not
be within the purchase scope or the usage scope. Unless otherwise specified in the contract, all
statements, information, and recommendations in this document are provided "AS IS" without warranties,
guarantees or representations of any kind, either express or implied.
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute a warranty of any kind, express or implied.
Website: http://www.huawei.com
Email: support@huawei.com
Contents
1 Hardware Architecture
1.1 Overview
1.1.1 Product Architecture
Figure 1-1 shows the product architecture of the LampSite solution in UMTS, LTE, or
UMTS+LTE mode.
Figure 1-1 Product architecture of the LampSite solution in UMTS, LTE, or UMTS+LTE mode
NOTE
The example hardware shown in Figure 1-1 can be applied in all modes. The BBU can be
configured with baseband boards at different modes to meet requirements of different scenarios, and the
pRRU can be configured with different RF daughter boards at different modes to support multimode
applications.
1.2 BBU3900
For more details about the BBU3900, see BBU3900 Description.
Table 1-1 describes the ports and certain features on the RHUB3908.
Label Description
CPRI0 Optical port used for signal transmission between the RHUB and
the BBU or between the RHUB and the upper-level/lower-level
CPRI1 RHUB
GE0/1 FE/GE electrical port (reserved)
EXT_ALM Dry contact alarm port used for monitoring backup power system
alarms
ETH Reserved port
PWR0~7/CPRI_E0~ Power supply port and transmission port between the RHUB and
CPRI_E7 the pRRU.
Power input socket Port for AC power input
RST Hardware reset button for initializing configurations
Ground screw Used for connecting PGND cables. If PGND cables use a one-hole
OT terminal, connect them to the ground screws at the bottom of
the panel.
1.3.3 PSU
The PSU converts 110 V/220 V AC power into –57 V DC power.
Figure 1-5 shows the PSU exterior.
NOTE
The buckle and handle are used to physically install the PSU in the RHUB box.
Port Description
ANT0 A port connected to the external antenna to transmit and
receive signals. If the pRRU has built-in antennas, ports
ANT1 ANT0 to ANT5 are not required. If the pRRU is
configured with the RU1 daughter board and no built-in
antenna is installed, the ANT0 or ANT1 port is connected
to the external antennas.
ANT2 A port connected to the external antenna to transmit and
receive signals. If the pRRU has built-in antennas, ports
ANT3 ANT0 to ANT5 are not required. If the pRRU is
configured with the RU2 daughter board and no built-in
antenna is installed, the ANT2 or ANT3 port is connected
to the external antennas.
ANT4 A port connected to the external antenna to transmit and
receive signals. If the pRRU has built-in antennas, ports
ANT5 ANT0 to ANT5 are not required. If the pRRU is
configured with the RU3 daughter board or Wi-Fi
daughter board and no built-in antenna is installed, the
ANT4 or ANT5 port is connected to the external
antennas.
PoE A port connected to the RHUB. It supports the PoE and is
CPRI_E0 used to transmit CPRI data between the RHUB and the
pRRU.
The PoE emblem indicates that
the CPRI_E0 port supports the
PoE power supply.
In SRAN9.0 or later, if the customer requires the WLAN network deployment in addition to
the UMTS/LTE network, pRRUs with Wi-Fi daughter boards can be purchased and connected
to the WLAN network through GE ports on the pRRUs.
Item Specifications
Dimensions Height (mm) Width (mm) Depth (mm)
43.6 482 310
Weight ≤ 8 kg
Input voltage 100 V AC to 120 V AC; 200 V AC to 240 V AC
Transmission Eight FE/GE electrical ports
port Two FE/GE optical ports
Power < 40 W
consumption
Power supply 8x90 W: A CPRI_E provides a power supply of 90 W.
Item Specifications
Dimensions Height (mm) Width (mm) Depth (mm)
230 230 50
Weight ≤ 3 kg
Input voltage AC/DC power: 100 V AC to 120 V AC; 200 V AC to 240 V AC
PoE: -36 V DC to -60 V DC
Transmission port Three FE/GE electrical ports
Power consumption With one RF daughter board: ≤ 30 W
With two RF daughter boards: ≤ 50 W
With three RF daughter boards: ≤ 70 W (One of the three RF
daughter boards is a Wi-Fi daughter board.)
Item Specifications
Item Specifications
EMC The base station complies with the following standards related to
electromagnetic compatibility:
CISPR22 Class B
VCCI Class B
GB9254 Class B
IEC61000-3-2
IEC61000-3-3
IEC 61000-4-2
IEC 61000-4-3
IEC 61000-4-4
IEC 61000-4-6
IEC 61000-4-11
3GPP R99, R4, R5, R6, R7, R8, R9, and R10
Environment RoHS
protection standard
Surge protection IEC61000-4-5 surge immunity
standard
Protection standard YD 5098-2001
IEC 61000-4-5
ETSI EN301 489
ITU-T K.20
Safety Standards IEC60950
Environment standard ETSI EN 300 019-2-1
ETSI EN 300 019-2-2
ETSI EN 300 019-2-3
IEC 60068-2