Академический Документы
Профессиональный Документы
Культура Документы
Página 1 de 6
Shutdown SIS
Previous Screen
i02289375
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
C 1U-9200 Lever Puller Hoist 3
D 138-7574 Link Bracket 3
E 140-7742 Sleeve 3
F 6V-2012 Depth Micrometer 1
Micrometer
G - 1
1-2 inch
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019
834H Wheel Dozer BTX00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Página 2 de 6
Illustration 1 g01146023
1. Install Duo-Cone seal (16) to spindle (18). Refer to Disassembly and Assembly, "Duo-Cone
Seals - Install". Raise the temperature of bearing cone (17). Install bearing cone (17) to
spindle (18) .
Illustration 2 g01146022
2. Lower the temperature of bearing cups (13) and (14). Install bearing cups (13) and (14) to
wheel (3). Install Duo-Cone seal (15). Refer to Disassembly and Assembly, "Duo-Cone
Seals - Install".
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019
834H Wheel Dozer BTX00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Página 3 de 6
Illustration 3 g01146074
3. Attach Tooling (C), Tooling (D), and a suitable lifting device to wheel (3) and position
wheel (3). The weight of wheel (3) is approximately 250 kg (550 lb). Attach Tooling (A) to
guard assembly (7). Attach Tooling (D) to wheel (3). Attach Tooling (C) to Tooling (A) and
Tooling (D) in order to secure wheel (3) .
Illustration 4 g01145927
Illustration 5 g01145959
5. Raise the temperature of bearing cone (12) and install bearing cone (12) onto hub assembly
(5) .
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019
834H Wheel Dozer BTX00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Página 4 de 6
Illustration 6 g01145919
6. Attach a suitable lifting device and Tooling (E) to hub assembly (5). The weight of hub
assembly (5) is approximately 68 kg (150 lb). Install hub assembly (5) into ring gear (10).
Install bolts (9) .
Illustration 7 g01146079
Illustration 8 g01146024
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019
834H Wheel Dozer BTX00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Página 5 de 6
Illustration 9 g01144927
7. Attach a suitable lifting device and Tooling (E) to hub assembly (5) and position hub
assembly (5) and ring gear (10). The combined weight of hub assembly (5) and ring gear
(10) is approximately 159 kg (350 lb).
8. Use Tooling (F) in order to measure the thickness of retainer (6) at three Locations (X).
Average the readings and record the measurement.
9. Position retainer (6) without shims (8). Install bolts (4) in the numeric sequence that is
shown in Illustration 9. Tighten bolts (4) to a torque of 112 ± 18 N·m (83 ± 13 lb ft).
10. Remove Tooling (D) from both sides of wheel (3). Remove the suitable lifting device from
hub assembly (5). Rotate wheel (3) for one full revolution.
11. Loosen bolts (4) slightly. Tighten bolts (4) according to the tightening sequence in
Illustration 9. Tighten bolts (4) to a torque of 50 ± 9 N·m (37 ± 7 lb ft). Rotate wheel (3) for
one full revolution.
12. Use Tooling (G) in order to take three measurements at Locations (X). Average the readings
and record the measurement.
13. Subtract the measurement that was recorded in Step 8 from the measurement that was
recorded in Step 12. Add 0.10 mm (0.004 inch) to this measurement. Record the
measurement. This measurement is the total shim pack thickness that is required.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019
834H Wheel Dozer BTX00001-UP (MACHINE) POWERED BY C18 Engine(SEB... Página 6 de 6
14. Use Tooling (G) in order to measure the thickness of shims (8). The thickness of shims (8)
must be within 0.025 mm (0.0010 inch) of the measurement that was recorded in Step 13.
15. Attach a suitable lifting device to hub assembly (5). Attach Tooling (D), Tooling (C), and
Tooling (E) to wheel (3) in order to secure wheel (3). Remove bolts (4) and retainer (6) .
16. Position shims (8) and retainer (6). Install bolts (4). Tighten bolts (4) to a torque of 530 ± 70
N·m (391 ± 52 lb ft).
Illustration 10 g01145838
17. Attach Tooling (A) and a suitable lifting device to final drive (2) and position final drive
(2). The weight of final drive (2) is approximately 136 kg (300 lb).
End By:
a. Install the rear axle shafts. Refer to Disassembly and Assembly, "Axle Shaft - Remove and
Install".
b. Install the rear tires and rimsfor the 834H. Refer to Disassembly and Assembly, "Tire and
Rim (Rear) - Install".
c. Install the rear compactor wheels for the 836H. Refer to Disassembly and Assembly,
"Compactor Wheels (Rear) - Install".
Copyright 1993 - 2019 Caterpillar Inc. Mon Dec 9 09:08:59 EST 2019
All Rights Reserved.
Private Network For SIS Licensees.
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis... 09/12/2019