Академический Документы
Профессиональный Документы
Культура Документы
Part Information
a) Air cleaner replacement (Only if it is deformed)
➊
Only if you find a
Air cleaner 204‐00066 1
deformed air cleaner
Service Bulletin
Repair Procedure
DL300A/ DL420A
*Note: Only replace air cleaner if
deformed
1 Loosen the clamp band bolt
2 Loosen the clamp band bolts(2ea)
and washers(2ea) 1 5 3 2 6
3 Disconnect air cleaner from hose
4 Replace air cleaner with new one w
hen you find a deformed air cleaner
only
*Note: New air cleaner will include
filters
5 Install the clamp band bolt
6 p ( )
Install the clamp band bolts(2ea)
and washers(2ea)
Service Bulletin
b) Turbocharger heat screen addition
➊ Bracket 110515‐00264 1
➋ Heat screen 110523‐00009 1
Repair Procedure
DL300A/ DL420A
*Note: If there is already a heat
1
screen, remove it first.
1 Loosen clamp and slide away from
turbocharger
3 IInstall S0504566
t ll S0504566 nuts and washers
t d h
(4ea) to assemble 110515‐00264
bracket with 110523‐00009 new
heat screen
Torque bolts to 10 N‐m
(1 kgf‐m, 7 lbf‐ft)
*Note: Over tightening nuts could
damage washer and heat screen
Do not use an impact gun
Service Bulletin
Repair Procedure
DL300A/ DL420A
4 Add bracket with new heat screen
to the turbocharger flange
Torque bolts to 64 N‐m
(6.5 kgf‐m, 47 lbf‐ft).
4
Service Bulletin
c) Heat‐resistant foam
1 1
Repair Procedure
DL300A/ DL420A
1 Loosen M8 nut and washer to
remove gas spring from side door 4
1
2 Remove existing side cover foam
*Note: Door surface must be clean
before installing new foam
3 Install
2
• 180309‐00201 heat‐resistant foam
(DL300A)
(DL300A)
• 180309‐00189 heat‐resistant foam
(DL420A)
4 Reinstall M8 nut and washer to
reinstall the gas spring on side door
3
Service Bulletin
d) Air flow improvement – DL420A
1 1
➊ Cover; side 110517‐00691 1
Service Bulletin
Repair Procedure
DL420A
1 Remove M10 bolts (3ea) and
disassemble maintenance cover
2 Remove M12 bolts (2ea)
*Note: Please be careful not to lose
p
spacer between cover and fender
Spacer
2
1
Service Bulletin
Repair Procedure
DL420A
3 Remove bolts (6ea) and remove
existing side cover
*Note: If there is not an existing
baffle, you don’t need to follow
step 4.
4 Remove bolts (3ea) and remove a
baffle (discard parts)
4
Service Bulletin
Repair Procedure
DL420A
5 Reinstall bolts (6ea) to assemble
110517‐00691 new cover side
5
Service Bulletin
Repair Procedure
DL420A
6 Install spacer between cover and
fender when you install M12 bolts
(2ea)
Torque bolts to 108 N
Torque bolts to 108 N‐m
m
(11 kgf‐m, 80 lbf‐ft)
7 Install M10 bolts (3ea) to assemble
maintenance cover
maintenance cover
Torque bolts to 64 N‐m
(6.5 kgf‐m, 47 lbf‐ft)