Академический Документы
Профессиональный Документы
Культура Документы
Introduction
This addendum describes how to implement a FR-320 Releasing panel into a FleX-Net™ system panel.The
FR-320K adds releasing capability to the FleX-Net™ system without the need for a separate external cabinet.
About the FR-320NetK Intelligent Network Fire Alarm and Release Control System
The FR-320K panel adds releasing capability to Mircom's FleX-Net™ MNS. Based upon Mircom's already UL
listed FR-320 Releasing panel and FleX-Net™ systems, this system permits pre-release, abort, manual
release, and reset control.
The FR-320K's chassis permits easy mounting to the Mircom's BBX-FXMNS cabinet. The FR-320K includes
all necessary items to connect the FR-320 releasing panel to the Mircom's FleX-Net™ system.
The FleX-Net™ and FR-320K panels have independent power arrangements. Each panel has its own AC
supply and battery setup. The connection between the FR-320K and the FleX-Net™ panels is by isolated
relays.
The FR-320K uses the FR-320 pre-programmed mode #2 to enable activation features via the FleX-Net™
initiating device circuits. In this configuration, the Mass Notification System (MNS) capability is not present at
this panel node.
Note: The releasing devices used must be wired locally to this panel.
Overall Features:
FR-320K FR-320 Main Board and Agent Releasing Kit for FleX-Net™
• Hexnut driver
• Phillips screwdriver
Chassis Mounting
Using the CH-1183 support plate, anchor the FR-320K to the FXMNS back box in the area above the FX-
2000MNS board. Otherwise, physical installation is as listed in each component’s manual.
CH-1183
Support Plate
FR-320K
FR-320
BBX-FXMNS
Board
Backbox
RM-306
Board
FR-320
Batteries
FR-320
Transformer FX-2000N
AC transformer
FX-2000N
Board CH-1181
Support Plate
DM-1008A
Board
RM-1008A FX-2000N
Board SGM-1004A Batteries
Board
Board Mounting
Mount all other boards in as illustrated. Otherwise, physical installation is as listed in each component’s
Installation and Operation manuals:
• LT-894 FleX-Net™
• LT-951 FR-320
• LT-847 MGD-32
FR-320K
RAM-1016TZDS
MGD-32 RM-306
RAX-1048TZDS
FX-2000MNS
SGM-1004A
DSPL-420
DM-1008A RM-1008A
The FR-320K has its own AC transformer and battery hookups, independent from the other FleX-Net™
components.
Initiating Circuits 6 supervised style B (Class B) initiating circuits, configurable. Terminals are
labeled DET. Compatibility ID A.
Power limited / 19VDC reg. / 3mA for detectors /110MVpp AC ripple / 45mA max
(alarm short)
Supervised Auxiliary
Power limited / 21.1VDC regulated / 300mA max
Power (non resettable)
RS-485 Connection For Remote Annunciators. Terminals are labeled RS485. Line impedance is 120
ohms.
Electrical ratings AC line voltage 120 VAC 60Hz 1.2A / 240 VAC 50 Hz 0.6 A, 10A
slow blow fuse on secondary of transformer
If no auxiliaries are used the max power is 4A for the indicating and the releasing
circuits
Auxiliary relays Must be connected to a listed power limited source of supply. Terminals
(resistive loads) are labelled ALARM, TROUBLE, SUPV and AUX.
Applicable Standards NFPA 12, 12A, 12B, 12, 15, 16,70,72,2001, UL-864
Rev. 9
Field Wiring
Adding the FR-320K to the FleX-Net™ system is straight forward as both boards are located in the same
backbox. This reduces the need for extra conduit and running long cables.
1. For general wiring options (i.e. ribbon cables), refer to these installation and operation manuals:
• LT-894 FleX-Net™
• LT-951 FR-320
• LT-847 MGD-32
• LT-617 RAM-1016TZDS
2.Use the following diagrams to wire up the FR-320K:
Rly 6 C
+
JW 5
From RM-1008A,
DET 1
-
Relay 2 and 6
+
For front panel programming use CFG-300
DET 2
Figure 3
-
configuration tool not UL - 864 or ULC-S 527
listed. Please refer to Document LT-922 for details.
+
-
DET 3
+
AC ON IAC1
DET 4
(ZONE 1)
-
X COMMON ALARM
COMMON SUPV IAC2
From RM-1008A, Relay 3 and 7
+
COMMONTROUBLE (ZONE 2)
Rly 3 NO
2.1 Wiring for FR-320K panel
Initiating zones 1 to 6
M
DET 5
BATTERY TROUBLE
+
JW 4 (ZONE 3)
+
? GROUND FAULT Rly 4 NO
FR-320K Panel
-
DET 6
CPU FAIL IAC4
RS-4 85
ABORT
(ZONE 4) Rly 8 C
S
To MGD-32 JW 7 From RM-1008A, Relay 4 and 8
RELEASE IAC5
(ZONE 5)
NO
RS-485 SYSTEM
STYLE Y
JW 5
+
RESET IAC6 WIRING
C
Input JW 6 (ZONE 1)
SIG 1
-
SIGNAL INDICATING
AUX. RE LAY
NC
SILENCE CIRCUIT - 1
+
AUXILIARY NAC1
NO
SIG 2
-
DISCONNECT (ZONE 1)
C
STYLE Y
LAMP NAC2 WIRING
+
TEST (ZONE 2)
NC
AL ARM RELAY
SIG 3
-
+ BUZZER RAC1 INDICATING
NO
SILENCE (ZONE 3) CIRCUIT - 2
+
-
C
SIG 4
PRE RAC2
RELAY
To DM-1008A IN4 RELEASE (ZONE 4) Solenoid Coil
NC
SUPERVISORY
+
+ AUX
Indicating/Releasing zones 1 to 4
NO
-
C
Solenoid EOL
+
RELAY
TROU BLE
module
NC
-
JW 1 JW 2
RTI PORT UNFLTD SPLY
T O PR-300 MO DUL E TO RM-306 RE LAY MOD UL E POWER
SIGNAL TRB TRL COM- COM+ Solenoid Coil
P3 P4
Solenoid EOL
module
Legend: MP-320R/W
Figure 4
A
LOOP 2
+ refer to FleX-Net
P3 P4
+
-
NO
NC
NO
NC
NO
NC
S
S
SIG GND
COM
COM
COM
- LT-894 Manual
or COM(-)
RS485 TROUBLE ALARM SUPV. 4-WIRE +
POWER
SUPPLY -
2.2 Wiring for FX-2000MNS
FX-2000MNS Panel
P3 P4 NAC 0
+
INDICATION +
CIRCUIT 1
JW1 FIELD WIRING TERMINALS (POWER-LIMITED) -
JW5 -
P16
NAC 1
+
P5 INDICATION
CIRCUIT 2 +
JW6 (POWER-LIMITED)
-
-
MAIN FIRE ALARM BOARD +
NAC 2
INDICATION +
CIRCUIT 1
JW4 (POWER-LIMITED)
P9 -
P6
P14 P19 -
+
NAC 3
INDICATION +
P8 CIRCUIT 2
(POWER-LIMITED) -
SW2 -
ON TS2
E+
P2 P1 P10 P11 NAC External
P7 1 8 I+
Power Connection _
+ BR - +BAT -
P18 JW2
J1
P15 F1
Rly 5 C
+ +
24 VDC
24 VDC OUTPUT POWER FROM MGD-32 Module
INPUT
- -
24 VDC +
OUTPUT
-
+ +
RS-485 OUTPUT FROM MGD-32 Module
RS-485 S
INPUT
- -
+
RS-485
OUTPUT S
P11
Relay 3 NO
To DET5 on FR-320 panel Det 5+
System Det 5-
Relay 1 NO Relay 7 C
Reset
COM
Relay 5 C
Relay 4 NO
To System Det 6+
Rese t on To DET6 on FR-320 panel
Det 6 -
MGD-32
module
Relay 8 C
Relay 5 NC Relay 7 NC
Relay 8 NC
COM
COM
COM
COM
CONTACTS
NO
NO
NO
NO
NC
NC
NC
NC
28 VDC, 1 AMP
RESISTIVE LOAD
RLY 4
RLY 3
RLY 1
RLY 2
RESISTIVE LOAD
RESISTIVE LOAD
RESISTIVE LOAD
RESISTIVE LOAD
28 VDC, 1 AMP
28 VDC, 1 AMP
28 VDC, 1 AMP
28 VDC, 1 AMP
AUX RELAY 8
AUX RELAY 7
AUX RELAY 5
AUX RELAY 6
CONTACTS
CONTACTS
CONTACTS
CONTACTS
COM
COM
COM
COM
NO
NO
NO
NO
NC
NC
NC
NC
RLY 7
RLY 8
RLY 5
RLY 6
P1
To DM-1008A
Relay INI7
INI7-
INI7+
Figure 8 RM-306 Six Relay Adder Module
Figure 9
INI 3+
Note: Initiating circuits of the DM-1008A should be Style B (Class B) by
default . If Style D (Class A) used, the FleX-Net Configurator must be set
INI 3- to NOT use Cross-zone Detection Zones.
STYLE B/D
2.7 Wiring for DM-1008A
INI 2 INI 4+ NO
From FR-320 Supervisory Relay
INI 4- C
DM-1008A Module
3.9K 1/2 WATT ELR
OR ELRX-300/R
INI 5-
STYLE B/D
INI 3
INI 6+
INI 7+
INI 7- NO
STYLE B/D
INI 4
From RM-306 Relay Adder Module Relay 3
INI 8+ C
Legend:
INI 8-
3.9K 1/2W ELR LISTED S5434
SMOKE DETECTOR MODEL MP-300
MANUFACTURED BY MIRCOM
HEAT DETECTOR
ABORT SWITCH
CONNECT A UL/ULC LISTED
ABORT STATION ACCEPTABLE TO
THE AHJ, COMPLYING WITH THE
PULL STATION FOLLOWING SPECIFICATIONS
MAXIMUM IMPEDENCE =1.4K OHMS
RATED CURRENT = 45mA
MANUAL RELEASE RATED VOLTAGE= 24V
SWITCH
Use MS-403,404
From FR-320 Trouble Relay USE ONLY NO
CONTACT
C NO
Pre- Programmed Mode
Pre-programmed Mode 2 is the FR-320K default program setting which includes new features.
Note: Cross Zone smokes detectors must not use verified alarm.
Zone Configuration
The FleX-Net™ monitors the Detection Zones via relay control. Connect either Detection Zone 1 or 2, but not
both.
• NAC-1: Signal, will be on steady if there is any alarm zone or manual release switch
active
• NAC-2: Signal, indicates the cadence of hazard area 1 state or supervisory circuit
(optional)
• RAC-1: Releasing Circuit (Hazard Area 1)
• RAC-2: Releasing Circuit (Hazard Area 1)
Hazard Configuration
• Default Release Timer Value: 60 seconds
NAC Configuration
• Default Escalating NAC code of Hazard Area State:
•Hazard Idle: Off
•Hazard Alert: Temporal
•Hazard Alarm: Temporal
•Hazard Release: Steady
• Default NAC code of Supervisory Signal is 20 BPM
The following is an example of how the FleX-Net™ and FR-320K system can work, based on Preprogrammed
Mode 2. Full setup options are available via the FleX-Net™ Configurator software.
Compatible Solenoids
The following table lists the solenoids with the FR-320K.