Академический Документы
Профессиональный Документы
Культура Документы
B
September 2015
enterprise.alcatel-lucent.com
enterprise.alcatel-lucent.com Alcatel-Lucent and the Alcatel-Lucent Enterprise logo are trademarks of
Alcatel-Lucent. To view other trademarks used by affiliated companies of ALE Holding, visit: enter-
prise.alcatel-lucent.com/trademarks. All other trademarks are the property of their respective owners. The
information presented is subject to change without notice. Neither ALE Holding nor any of its affiliates
assumes any responsibility for inaccuracies contained herein. (July 2015)
This chapter provides a brief overview of the Alcatel-Lucent Enterprise SMB (small-medium business)
solution along with the steps for quickly configuring the various components. For more detailed step-by-
step instructions refer to the appropriate configuration chapter.
In This Chapter
The information described in this chapter includes:
• “Overview” on page 1-2
Overview
This configuration guide covers how to install the various components of the Alcatel-Lucent Enterprise
SMB (small-medium business) solution. The SMB market can be addressed via two Alcatel-Lucent Enter-
prise solutions: one includes an OmniSwitch™ and OmniAccess™ Instant Access Points (IAPs), enabling
high speed wired and wireless (Wi-Fi) LAN access, referred to as the Mobility solution, while the second
includes OmniPCX™ Office RCE, providing IP Telephony, for a complete voice/data/Wi-Fi solution.
This SMB Configuration Guide describes the installation steps based on the following products.
• OmniPCX™ Office RCE
Note: Minimum version R10.2 is required for the OmniPCX Office RCE information described
in this document. See “Upgrade Information” on page 1-5 for information on upgrading to R10.2.
• OmniSwitch OS6450-P24
• OmniSwitch OS6450-P48
• OmniSwitch OS6450-P10
• OmniSwitch OS6450-P10L
• OmniSwitch OS6250-P24
• OmniSwitch OS6450-P24L
• OmniSwitch OS6450-P48L
• OmniSwitch 6350-P24
• OmniSwitch 6350-P48
• OAW-IAP
Chapter 1 provides quick steps to configure these products, Chapter 2 provides a detailed procedure to
configure OmniPCX Office RCE, the OmniSwitch and the OAW-IAP, and Chapter 3 provides a detailed
procedure to configure the OmniSwitch and OAW-IAP when OmniPCX Office RCE is not installed.
For additional solution information please refer to the SMB Solution Sheet.
2 The os_script script file contains the following command for certifying the configuration:
3 The os_ins.alu instruction file contains the following entries describing the location and file names
needed by the OmniSwitch:
1 Connect an Ethernet cable between the OmniPCX Office RCE and the OmniSwitch.
3 The OmniSwitch will boot up and automatically download the configuration files from the OmniPCX
Office RCE. Once the download is complete, the OmniSwitch will reboot again. This process will take
approximately 6 to 8 minutes.
Note. Alcatel-Lucent recommends that you change the administrator credentials after the initial configura-
tion.
Note. If the country code window is displayed after a successful login, select a country from the list.
5 From the AOS-W Instant UI main window, click New under the Networks section. The New WLAN
window is displayed.
6 In the New WLAN setting tab, enter an SSID name for the network and click Next.
7 In the VLAN tab, select the required Client IP assignment and Client VLAN assignment options and
click Next.
8 In the Security tab, enter a unique passphrase and retype it to confirm and click Next.
9 In the Access tab, ensure that the Unrestricted access control is specified and click Finish.
Note. After the secure wireless network access is configured, Alcatel-Lucent recommends deleting the
instant SSID to protect from unauthorized wireless access.
Upgrade Information
When upgrading to OmniPCX Office RCE version R10.2:
• The old default configuration files will be replaced with the new default configuration files of R10.2.
This chapter describes the detailed configuration steps to install the SMB solution with the OmniPCX
Office RCE.
In This Chapter
The information described in this chapter includes:
• “OmniPCX Office RCE Setup for OmniSwitch Auto Configuration” on page 2-2
2 Connect an Ethernet cable between the OmniPCX Office RCE and the OmniSwitch.
4 The OmniSwitch will boot up and automatically download the configuration files from the OmniPCX
Office RCE. Once the download is complete, the OmniSwitch will reboot again. This process will take
approximately 6 to 8 minutes.
IAP Configuration
The next process in the installation of SMB is the IAP configuration. This section describes the steps to
configure the IAP.
2 Connect an Ethernet cable between IAP and OmniSwitch, wait for approximately 6 minutes for the
IAP to initialize.
Ethernet
3 Wait for all LEDs on the IAP to turn green and blink.
Connecting to SSID
Note. Alcatel-Lucent recommends that you change the administrator credentials after the initial configura-
tion. For more information, see the Management Authentication Settings section in AOS-W Instant User
Guide.
Note. If the country code window is displayed after a successful login, select a country from the list. The
country code window is displayed only when OAW-IAP-ROW (Rest of world) variants are installed. The
country code setting is not applicable to the OAW-IAPs designed for US, Japan, and Israel.
a. From the AOS-W instant UI main window, click New under the Network section. The New
WLAN window is displayed.
b. In the New WLAN setting tab. Enter an SSID name for the network and click Next.
c. In the VLAN tab, select the required Client IP assignment and Client VLAN assignment
options and click Next.
d. In the security tab, enter a unique passphrase and retype it to confirm. Click Next.
e. In the Access tab, ensure that the Unrestricted access control is specified and click Finish.
f. Try connecting to the new SSID that was just created. Ensure network access before proceeding to
deleting instant SSID step.
3 Delete the instant SSID to protect from unauthorized wireless access. Follow the steps below to delete
Note. For multiple OAW-IAPs deployment, IAPs automatically find each other in same subnet and form a
single functioning network managed by a Virtual Controller. It is recommended to configure a virtual
controller IP in a multiple IAP deployment scenario. Please refer to user manual for configuration proce-
dure.
This chapter describes the detailed configuration steps to configure the SMB solution without an
OmniPCX Office RCE.
In This Chapter
The information described in this chapter includes:
• “OmniSwitch Configuration” on page 3-2
OmniSwitch Configuration
To install the SMB solution without an OmniPCX Office RCE the OmniSwitch must be manually config-
ured. To configure the OmniSwitch follow the below steps:
1 The OmniSwitch should be in the factory default mode with no boot.cfg file.
3 Connect to the console and log in to the OmniSwitch CLI with admin and switch as the username and
password, respectively.
Console Connection
IAP Configuration
The next process in the installation of the SMB solution is the IAP configuration. This section describes
the steps to configure the IAP.
2 Connect an Ethernet cable between IAP and OmniSwitch, wait for approximately 6 minutes for the
IAP to initialize.
Ethernet
3 Wait for all LEDs on the IAP to turn green and blink.
Connecting to SSID
Note. Alcatel-Lucent recommends that you change the administrator credentials after the initial configura-
tion. For more information, refer the Management Authentication Settings section in AOS-W Instant User
Guide.
Note. If the country code window is displayed after a successful login, select a country from the list. The
country code window is displayed only when OAW-IAP-ROW (Rest of world) variants are installed. The
country code setting is not applicable to the OAW-IAPs designed for US, Japan, and Israel.
a. From the AOS-W instant UI main window, click New under the Network section. The New
WLAN window is displayed.
b. In the New WLAN setting tab, enter a SSID name for the network and click Next.
c. In the VLAN tab, select the required Client IP assignment and Client VLAN assignment
d. In the security tab, enter a unique passphrase and retype it to confirm and click Next.
e. In the Access tab, ensure that the unrestricted access control is specified and click Finish.
f. Try connecting to new SSID that was just created. Ensure network access before proceeding to
deleting instant SSID step.
3 Delete the instant SSID to protect from unauthorized wireless access. Follow the below steps to delete
the instant SSID:
Note. In a multiple OAW-IAP deployment, the IAPs automatically find each other in the same subnet and
form a single functioning network managed by a Virtual Controller. It is recommended to configure virtual
controller IP in multiple IAP deployment scenario. Please refer to AOS-W user manual for configuration
procedure.