Академический Документы
Профессиональный Документы
Культура Документы
Published 1984-07-15
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION• ME>K.QYHAPO,ll,HAR 0PfAHL-13AWL-1A no CTAHAAPH13AU~\o1· ORGANISATION INTERNATIONALE DE NORMALISATION
Amendment 1 to International Standard ISO 2857-1973 was developed by Technical Committee ISO .lTC 29, Small tools, and was
circulated to the member bodies in January 1983.
The member bodies of the following countries expressed disapproval of the document on technical grounds:
France
USA
--``,,,`,,``,,,,`,``,,``,```-`-`,,`,,`,`,,`---
page 6
The values for tolerances on the half-angle a/2 are based on the pitch of the thread and shall be in accordance with the values of
table 3.
--``,,,`,,``,,,,`,``,,``,```-`-`,,`,,`,`,,`---
1
1,25 ± 25'
1,5
1,75
2
± 20'
2,5
3
-------
3,5
4
4,5
± 15'
5
5,5
6
NOTE - For a g1ven p1tch, the half-angle tolerance a/2 has been
calculated so that the equivalent error on the virtual pitch diameter
does not exceed a stated proportion of the pitch diameter tolerance
T02 for the corresponding class 5 nut thread.
The stated proportion is B %, except for pitches finer than 0,4 mm
where it is 10 %. The calculated values have been rounded off to the
nearest 5' to bring them within the scope of practical measurement .
.,
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
No reproduction or networking permitted without license from IHS Not for Resale, 05/02/2014 11:35:13 MDT
ISO 2857-1973/ A 1-1984 I E)
Page 7
Clause 6
Delete the line before the last in the left-hand column and substitute:
Pege9
Annex A
In the table, replace the column "Tolerance on a and a/2" by the following:
~- Class of taps
-
Thread _ Toler. on d
d Pitch a/2 nominal
Designation p
-
nominal
M 1 1 1
-
M 1,1 1,1... 0,25 ± 70' 1' 1
-
M 1,2 1.2 1,2
-~--
--``,,,`,,``,,,,`,``,,``,```-`-`,,`,,`,`,,`---
Page 11
Annex 8
In the table, replace the column "Tolerance on a and a/2" by the following:
Class of taps
-
Thread Toler. on d
-
________________ _ a/2 nominal
d Pitch f------ -
Designation p
nominal
M 1 X 0,21 1
M 1,1 X 0,2 1 1 '1
- ---'-_- -----
M 1,2 X 0,2 1,2 1,2
- ---
M 1,4 X 0,2 1,4 1,4
± 70'
M 1,6 X 0,2 1,6 1,6
M 1,8 X 0,2 1,8 ~-1~8
-
M 2 X 0,25 2 2
-
M 2,2 X 0,25 2,2 2,2
- ---
M 2,5 X 0,35 2,5 2,5
f-- -
f.""_ 3 X 0,35 3 0,35 ± 50' 3
~-- 3,5__ X 0,35 3,5 3,5
--``,,,`,,``,,,,`,``,,``,```-`-`,,`,,`,`,,`---
M 4 X 0.5 4 ! 4
f--------------- -
4,5
~M...__:4'",5"---"x~._,o,C:5--l-_:::4,c:s~ o, 5
5
f - - - - __ - ± 35'
M 5 X 0,5 f- 5
-
M 5,5 X 0,5 5,5 5,5
M 6 X 0,_75 6 6
7 --- 0,75 ± 30'
M 7 X 0,75 7
M 8 X 1 8 8
f-------------------
M 9 X 1 9 9
f-------------------- - ----
~-10 X 1
10 10
M 10 X 1,25
1,25
f - - - - - - - - - - - - - - - - - - --
~2__ x __~~
12 - 12
M 12 X 1,5
_ -l~1,~5-+------------------------ - ± 25'
M 14 X 1,25
14 ~,25_ f - - - - - - - - - - - - - - - - - - - - - 14
M 14 X 1,5
___ f-------------- - -
1,5 15
~-
X
-- __15__ f--------------- - -
M 16 X 1.5 16
16__ 1,5 f - - - - - - - - - - - - - - - - - - - - - -
M 17 X 1,5 17
1-:.:'-"-___.':_'--""--J--17_ f--------------------- -
M 18 X 1,5
18 18
M 18 X 2 2 + 20'
-
M20 X 1,5 1,5 + 25'
20 20
M20 X 2 2 + 20'
M22 X 1,5 1,5 ± 25'
22 22
M22 X 2 2 ± 20'
. - --
M 24 X 1,5 ± 25'
24 -f-- - -- 24
M24 X 2 j 20'
•
Copyright International Organization for Standardization
Provided by IHS under license with ISO Licensee=University of Alberta/5966844001, User=sharabiani, shahramfs
No reproduction or networking permitted without license from IHS Not for Resale, 05/02/2014 11:35:13 MDT