Академический Документы
Профессиональный Документы
Культура Документы
Version: 2
Date: 2009-03-10
This manual, including all illustrations contained herein, is copyright protected. Use of this manual by any third
party in departure from the copyright provision is forbidden. No part of this manual may be reproduced, trans-
lated or electronically or photographically archived or altered without the express written consent from Sütron
electronic GmbH. Violations shall be cause for damage liability.
Sütron electronic reserves the right to make any changes that contribute to technical improvement.
Slim Line Touch Panel Overall Table of Contents
i
Overall Table of Contents Slim Line Touch Panel
ii
Slim Line Touch Panel Overall Table of Contents
A Index ........................................................................................................................A-1
iii
Overall Table of Contents Slim Line Touch Panel
iv
Slim Line Touch Panels Important Notes
1 Important Notes
1.1 Symbols
The symbols in this manual are used to draw your attention on notes and dangers.
Danger
This symbol is used to refer to instructions which, if ignored or not carefully followed
could result in personal injury.
Note
This symbol indicates application tips or supplementary notes.
The following symbols indicate specific dangers which could result in damage to
equipment or personal injury or even up to the death of the operator.
Danger - Corrosive
Danger - Toxic
Danger - Explosive
Danger - Fire
1-1
Important Notes Slim Line Touch Panels
– Read this manual carefully before using the operating device. Keep this manual
in a place where it is always accessible to all users.
– Proper transportation, handling and storage, placement and installation of this
product are prerequisites for its subsequent flawless and safe operation.
– This user manual contains the most important information for the safe operation
of the device.
– The user manual, in particular the safety notes, must be observed by all person-
nel working with the device.
– Observe the accident prevention rules and regulations that apply to the operating
site.
– Installation and operation must only be carried out by qualified and trained per-
sonnel.
This is a class A device. This device may cause radio interference in residential ar-
eas. In this case, the user may be required to introduce appropriate countermea-
sures, and to bear the cost of same.
1-2
Installation and Commissioning
Unpack all parts carefully and check the contents for any visible damage in transit.
Also check whether the shipment matches the specifications on your delivery note.
If you notice damages in transit or discrepancies, please contact our sales depart-
ment immediately.
When installing the device, leave a gap of at least 30 mm (1.181") around the device
to ensure sufficient air circulation.
When the operating device is installed horizontally, please note that additional
sources of heat beneath the operating device may result in heat accumulation.
Make sure to allow sufficient heat dissipation!
Comply with the allowable temperature range listed in the technical data for the use
of the operating device!
To ensure the specified degree of protection, make sure that the seal rests flat on the
mounting surface and the threaded pins of the mounting brackets are uniformly tight-
ened.
The device can be easily and quickly mounted from the rear of the device. Ideally,
the device should be installed in switch panels with a plate thickness of approx. 1 mm
to 6 mm (0.039" to 0.236").
1. Insert the device in the mounting cutout from the front.
2. Insert the mounting brackets into the appropriate openings (figure 1) and pull the
brackets downwards until they lock in place (figure 2).
3. Fasten the device into position using the threaded pins (figure 3).
2-1
Installation and Commissioning
2-2
Installation and Commissioning
2-3
Installation and Commissioning
2-4
Installation and Commissioning
2-5
Installation and Commissioning
2-6
Installation and Commissioning
2-7
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-8
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-9
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-10
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-11
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-12
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-13
Installation and Commissioning
A Mounting Cutout
B Front Panel
2-14
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-15
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-16
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-17
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-18
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-19
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-20
Installation and Commissioning
1 Mounting Bracket
2 Threaded Pin
3 Mounting Surface Thickness 1 mm to 6 mm
4 Circumferential Seal
5 Front Panel
2-21
Installation and Commissioning
A suitable female connector strip of the type Phoenix COMBICON MSTB 2.5/3-STF
is supplied.
Cables with finely stranded conductors with a minimum cross-section of 0.75 mm²
(18 AWG) and a maximum cross-section of 2.5 mm² (14 AWG) must be used for the
supply voltage.
Hazardous voltages can exist inside electrical installations that can pose a danger to
humans. Coming in contact with live parts may result in electric shock!
2-22
Installation and Commissioning
Use the following procedure to connect the device to the supply voltage:
1. Strip approx. 30 mm (1.181") off the outer cable sheath and approx. 5 mm
(0.197") off the wires.
2. Fit the wires with wire end ferrules and connect the wires to the connector.
If shielded connecting cables are used in the supply voltage area, the shield should
be connected to pin 1.
2-23
Installation and Commissioning
4. Secure the female connector strip in place with a screw-type locking to prevent
it from slipping out.
A separate conductor must always be provided for the protective grounding at the
threaded bolt. The conductor must have a minimum cross-section of 1.5 mm² (16
AWG) and must be kept as short as possible.
2-24
Installation and Commissioning
2.4 Switching On
2-25
Installation and Commissioning
Start
Normal
Admin
Setup-Main
Update
Copy to Flash
Copy to USB
Import Settings
Home
Update Image
Update
Bootloader
Home
TouchScreen
& Registry
Save Registry
Settings
Change
Display Mode
Start Calibration
SNTP Settings
Home
Network
Settings
TCP/IP Info
Fix Settings
IP Address
Gateway
DNS
WINS
Home
DHCP
FTP Settings
Delete a user
Home
Device Name
Home
Settings
Contrast
Date / Time
Password
Printer
Page
Settings
Network Printer
Settings
Home
Information
Home
Start Batchfile
Exit
2-26
Installation and Commissioning
Admin
The following message is issued if the AppStarter.exe file does not exist.
AppStarter not found !
Update Exit
Touch Screen
Settings
& Registry
Network Start
Settings Batchfile
Update:
Update
Copy USB
Home
Stick
Update Image
Update
Bootloader
Copy to USB
Import
Settings
2-27
Installation and Commissioning
Save Registry
Home
Settings
Change
Display Mode
Start SNTP
Calibration Settings
2-28
Installation and Commissioning
A OK
A
A
LCD Saver
A
Server myserver.myhost.local
Interval [minutes] 5
OK Cancel
You can enter the address of a time server located in the intranet or Internet. The
synchronization interval is specified in minutes.
This entry is password-protected.
Network Settings:
Network Settings
TCP/IP Info:
TCP/IP Info
MAC: 0-7-93-FF-FF-CE
IP: 192.168.100.82
Mask: 255.255.255.0
Device Name: MyName
DHCP enabled
Gate: 000.000.000.000
1. DNS: 000.000.000.000
2. DNS: 000.000.000.000
1. WINS: 000.000.000.000
OK
2. WINS: 000.000.000.000
2-29
Installation and Commissioning
IP Address 000.000.000.000
OK Cancel
The system deselects DHCP and enters the settings from the IPSetting.ini file of the
USB stick. This file must exist in the root directory of the USB stick.
If no USB stick is connected the information is read from the registry.
This entry is password-protected.
Contents of the IPSetting.ini file:
[IPCONFIG]
IPAddress=172.016.042.150
SubnetMask=255.255.255.000
000.000.000.000
OK Cancel
The system deselects DHCP and enters the settings from the IPSetting.ini file of the
USB stick. This file must exist in the root directory of the USB stick.
If no USB stick is connected the information is read from the registry.
This entry is password-protected.
2-30
Installation and Commissioning
OK Cancel
The system deselects DHCP and enters the settings from the IPSetting.ini file of the
USB stick. This file must exist in the root directory of the USB stick.
If no USB stick is connected the information is read from the registry.
This entry is password-protected.
Contents of the IPSetting.ini file:
[IPCONFIG]
PrimaryDNS=172.016.042.150
SecondaryDNS=172.016.042.151
OK Cancel
The system deselects DHCP and enters the settings from the IPSetting.ini file of the
USB stick. This file must exist in the root directory of the USB stick.
If no USB stick is connected the information is read from the registry.
This entry is password-protected.
Contents of the IPSetting.ini file:
[IPCONFIG]
PrimaryWINS=172.016.042.150
SecondaryWINS=172.016.042.151
2-31
Installation and Commissioning
DHCP enabled
Save registry and restart device to
work with new parameters
OK
You may enable DHCP service. You must save this setting when exiting of by using
„Save Registry Settings“.
This entry is password-protected.
Network Settings, FTP Settings, Add new user:
Add new user
OK Cancel
You may enter a new user name. You have to assign a password to the user name
and to confirm it.
If at least one user name is added you cannot login to the FTP server as anonymous
anymore.
Network Settings, FTP Settings, List all users:
All users are listet within a DOS box.
Network Settings, FTP Settings, Delete a user:
Delete a user
OK Cancel
MyDeviceName
OK Cancel
2-32
Installation and Commissioning
You can define a device name with up to 14 characters. Via a FTP connection you
can access the device with the device name instead of the IP address.
This entry is password-protected.
Settings:
Settings
Contrast Home
Password Information
Settings, Contrast:
Contrast
Contrast Brightness
15 15
Color Depth
8 bpp
16 bpp
OK Apply Cancel
The operating mode setup main is displayed with default values for contrast and
brightness to ensure reading also at faulty values. If you change a value, you have
to confirm this in a dialog. If you press Cancel or 5 seconds pass without any action
the value is not accepted.
Depending on the display type different values can be influenced:
Table 2-2
2-33
Installation and Commissioning
Current Time OK X
15:00:00 AM
Time Zone
(GMT +01:00) Amsterdam, Berlin, Bern, Rome
Apply
Current Password
Enable Password
Change
OK Cancel
The password can be activated, deactivated or redefined. When the password is ac-
tivated, all password-protected dialog boxes can only be accessed if the password
has been entered successfully.
This entry is password-protected.
Settings, Printer:
Printer
Page Network
Settings Print
Home
OK Cancel
2-34
Installation and Commissioning
OK Cancel
User Name:
Password:
Domain:
OK Cancel
SNR: 1023456789
Image_Grafikpanel_EP9307_CE5.00_
V1.18
Built: Aug 27 2007 14:00:00
Flash Size: 16 MB
SRAM Size: 512 kB
PLC / VISU RAM: 0 / 460 kB
Busclock: 49 MHz
Click OK to go back to main
2-35
Installation and Commissioning
2-36
Installation and Commissioning
Mode=Standard The Shell is restricted: No task bar and task switch available.
Desktop contains the launch icon only.
The change becomes effective on the next device reboot.
DeviceName=MyName Defines the device name of the operating device
;DeviceName=MyName Comment, no impact
The AppStarter.exe program creates all the necessary registry settings and can also
store the registry, if desired.
If the Explorer is activated, the system shuts it down. Automatic startup of ActiveSync
is also deactivated.
The AppStarter.exe file then starts the TSvisLD_CE.exe file from the Flash File Sys-
tem (FFS).
2-37
Installation and Commissioning
The TSvisLD.exe loads the following components into the memory of the operating
system in accordance with the instructions in the TSvisRT_CE.ini file:
– User application
– Protocol driver
– TSvisRT firmware
The program then unpacks the compressed application file (*.CB) and starts the TS-
visRT Runtime component.
Legend:
2-38
Installation and Commissioning
2-39
Installation and Commissioning
2.5 Identification
The operating device can be identified using the nameplate on the rear of the device.
1 Order number
2 Version key (at time of delivery)
3 MAC address
4 Voltage and power specification
5 Serial number
The version key provides information on the version level of various components at
time of delivery.
Bundle
Bootloader
Image
Application Software
Installation /
Auxiliary Software
2-40
Control and Display Elements
3.1 Display
Danger - Toxic!
If the display is damaged, avoid touching, swallowing or breathing in the liquids or
gases which may leak out!
Danger - Corrosive!
If the display is damaged, avoid touching, swallowing or breathing in the liquids or
gases which may leak out!
To be able to set the brightness, you need to use the programming software to setup
the system variable LcdBackLight in a screen of your choice.
To do so, follow the instructions listed in the programming software's help topic "How
do I specify the contrast / brightness setting for the operating device".
In the programming software, enter the following values as lower and upper limits for
the representation type.
If you do not configure the system variable LcdBackLight, the default setting is used
when the device is initialized.
If you did set up the system variable, you can set the brightness as follows. Open the
screen where you set up the system variable and:
1. Press the button for brightness.
2. Enter a new value for the brightness. To do so, use the virtual keyboard.
3. Confirm with Enter.
The new brightness setting becomes effective immediately after the Enter button is
pressed. If necessary, repeat steps 2 and 3 until you are satisfied with the brightness.
3-1
Control and Display Elements
To be able to set the contrast, you need to use the programming software to setup
the system variable LcdContrast in a screen of your choice.
To do so, follow the instructions listed in the programming software's help topic "How
do I specify the contrast / brightness setting for the operating device".
In the programming software, enter the following values as lower and upper limits for
the representation type.
If you do not configure the system variable LcdContrast, the default setting is used
when the device is initialized.
If you did set up the system variable, you can set the contrast as follows. Open the
screen where you set up the system variable and:
1. Press the contrast button.
2. Enter a new value for the contrast. To do so, use the keyboard shown on the
screen.
3. Confirm with Enter.
4. Finally press the Data Release key.
The new contrast setting becomes effective immediately after the Enter key is
pressed. If necessary, repeat steps two and three until you are satisfied with the con-
trast.
3.1.4 Fonts
You can use Windows fonts. Windows and unicode character sets are possible.
3-2
Control and Display Elements
The device is equipped with a resistive 4 wire touch screen. You operate the device
using this touch screen.
Pointed or sharp objects, such as pens or fingernails, can lead to irreparable dam-
ages of the touch screen. Exclusively therefore use the fingertips or the aids indi-
cated in the technical data for the operation.
To protect the touch screen you can use special protection foils. You receive corre-
sponding protection foils directly from Sütron electronic.
3-3
Control and Display Elements
3-4
Interfaces of the Device
PROFIBUS-DP (X6)
RS485, RS232 (X6)
DeviceNet (X6)
CAN (X6)
MPI (X6)
TPxxxAx/70xxxx X - - - - - - X
TPxxxAx/78xxxx X X - - - - - X
TPxxxAx/74xxxx X - X - - - - X
TPxxxAx/75xxxx X - - X - - - X
TPxxxAx/76xxxx X - - - X - - X
TPxxxAx/73xxxx X - - - - X - X
TPxxxAx/72xxxx X - - - - - X X
The following figures show the TP21AM exemplarily for all operating devices de-
scribed in this manual.
4-1
Interfaces of the Device
4-2
Interfaces of the Device
A 10/100 Base-T Ethernet interface is located on the side of the operating device.
4.1.1.2 Cable
A twisted pair cable of the category 5 (CAT 5) type must be used. The maximum ca-
ble length is 100 m (328.084 feet).
4.1.1.3 Diagnostics
Ethernet diagnostics LEDs are located at the side of the operating device.
4-3
Interfaces of the Device
Using input devices not suitable for industrial use (e.g. keyboard, mouse) may de-
crease safety of operation. This includes input devices intended for home and office
use.
4.1.2.1 Cable
For the specification of a suitable cable, please refer to the „Universal Serial Bus
Specification Rev. 2.0“.
The maximum cable length for the cable used is 2.5 m (8.202 feet).
4-4
Interfaces of the Device
4-5
Interfaces of the Device
4-6
Interfaces of the Device
4.2.1.2 Termination
For point-to-point connections, always activate the termination. For multipoint con-
nections, only activate the termination at the cable end.
Designation Value
R1, R3 510 Ohm
R2 150 Ohm
R4 120 Ohm
The switch positions for ON or OFF are printed onto the termination switch. Only the
specified switch positions are allowed.
Switch on the transmitter termination (S1 + S2) and switch off the receiver termina-
tion (S3 + S4) if you terminate a RS485 interface.
S1 S2 S3 S4 Function
Transmit- Receiver
ter
– – – – Termination is OFF
I I – – Transmitter Termination is ON,
Receiver Termination is OFF
I I I I Transmitter Termination is ON,
Receiver Termination OFF
4-7
Interfaces of the Device
4.2.2.2 Termination
For the operation of channel SER1 as a RS232, the termination for the RS485 must
be OFF.
4-8
Interfaces of the Device
The CAN bus is a high speed bus in accordance with ISO-DIS 11898.
4-9
Interfaces of the Device
4.3.1.2 Cable
A shielded twisted-pair cable (cable type LiYCY-TP) complying with ISO 11898 must
be used.
Parameters Value
Impedance Min.: 108 Ohm
Nom.: 120 Ohm
Max.: 132 Ohm
Specific Resistance 70 mOhm/m
Specific Line Delay 5 ns/m
4-10
Interfaces of the Device
4.3.1.3 Termination
Terminate the CAN bus at both ends by terminating resistors (120 Ohm).
S1 S2 S3 S4 Function
X X I X Termination (120 Ohm)
X X – X No Termination
4.3.1.4 Diagnostics
A diagnostics LED is located on the rear of the operating device. The LED shows the
states of the bus system.
The diagnostics LED on the operating device has the following functions:
4-11
Interfaces of the Device
S1 S2 S3 S4 Function
X X X I High
X X X – Low
4-12
Interfaces of the Device
4-13
Interfaces of the Device
For the connection, use a 5 pin connector with gold-plated contacts and cover cap.
A suitable connector with cover cap can be obtained directly from Sütron electronic.
4.3.2.2 Cable
The maximum length allowed for spur lines connected to the bus cable is 6 meters.
The overall length of the bus cable including all spur lines is not to exceed the max-
imum length listed in the table below.
The maximum cable length depends on the baud rate and the cable type used.
4-14
Interfaces of the Device
4.3.2.3 Termination
Terminate the DeviceNet bus at both ends directly at the connector by terminating
resistors (120 Ohm).
4.3.2.4 Diagnostics
A diagnostics LED is located on the rear of the operating device. The LED shows the
states of the bus system.
The diagnostics LED on the operating device has the following functions:
4-15
Interfaces of the Device
The device can be integrated into the INTERBUS using the interfaces available for
INTERBUS connections.
4-16
Interfaces of the Device
Figure 4-12 9 pin D-SUB male connector strip and female connector strip
Connector in the terminal: 9 pin D-SUB male connector strip for remote bus in.
Connector in the terminal: 9 pin D-SUB female connector strip for remote bus out.
4.3.3.2 Cable
A shielded twisted-pair cable (cable type LiYCY-TP) must be used. The maximum
cable length depends on its use within the INTERBUS topology.
4-17
Interfaces of the Device
4.3.3.3 Diagnostics
The diagnostics LEDs are located at the rear of the operating device. The LEDs show
the states of the bus system.
The diagnostics LEDs at the operating device has the following functions:
4-18
Interfaces of the Device
4-19
Interfaces of the Device
4.3.4.2 Cable
Any cable that conforms with the following parameters can be used:
Parameters Value
Loop Resistance 110 Ohm/km
Capacitance 30 nF/km
Surge Impedance 150 Ohm
For further information on the installation, please refer to the Siemens manual "SI-
MATIC S7-400 and M7-400 Programmable Controllers Hardware and Installation,
6ES7498-8AA03-8BA0".
4-20
Interfaces of the Device
4.3.4.3 Termination
The bus line is terminated at the connector.
For point-to-point connections, always activate the termination. For multi-point con-
nections, only activate the termination at the cable end. For spur lines, always deac-
tivate the termination.
4.3.4.4 Diagnostics
A diagnostics LED is located on the rear of the operating device. The LED shows the
states of the bus system.
The diagnostics LED on the operating device has the following functions:
4-21
Interfaces of the Device
The interface for PROFIBUS-DP connections is available to integrate the device into
a PROFIBUS-DP structure.
4-22
Interfaces of the Device
4.3.5.2 Cable
Parameters Value
Impedance 136 to 165 Ohm
Capacitance < 30 pf/m
Loop Resistance 110 Ohm/km
Wire Gauge 0.64 mm
4-23
Interfaces of the Device
The maximum cable length depends on the baud rate (DIN EN 19245 Part 3).
4.3.5.3 Termination
Terminate the PROFIBUS at both ends by terminating resistors. If you are using spe-
cial PROFIBUS connectors, these resistors are usually integrated into the connector
and can be connected.
4.3.5.4 Diagnostics
A diagnostics LED is located on the rear of the operating device. The LED shows the
states of the bus system.
The diagnostics LED on the operating device has the following functions:
4-24
Interfaces of the Device
1 D-SUB connector
2 Shield
3 Cable clip
4 Cable
The shield must be folded back into a flat position over the cable sheath.
When fastening the cable with the cable clip, as much of the shielding as possible
must be in contact with the housing and sufficient strain relieve must be ensured.
4-25
Interfaces of the Device
4-26
Maintenance and Servicing
Only use a damp cloth to remove any dirt from the front panel.
5.2 Fuse
A semiconductor fuse is used to protect the device. Once the fuse has been tripped,
the device must be disconnected from the supply voltage to allow the semiconductor
fuse to regenerate. At an ambient temperature of 20 °C (68 °F), the regeneration
takes approximately 20 seconds. The higher the ambient temperature, the longer the
regeneration takes.
5.3 Battery
The built-in battery preserves the data in the SRAM and supplies the real-time clock
with power. The minimum battery life is 5 years, even under unfavorable operating
conditions. When the battery runs down, the message "Change battery" is generated
automatically.
We recommend you change the battery approximately every 4 years as part of the
regular maintenance work. A prepared battery including connector can be obtained
directly from Sütron electronic.
If the "Change battery" message is detected too late, data in the SRAM may have
already been lost. For this reason, after changing a battery, always check data such
as editable passwords, parameters in the system variables, data sets of the recipes
and entries in the message system.
5-1
Maintenance and Servicing
At operating devices for the explosive area the batteries must only be changed by
Sütron electronic GmbH.
For changing the battery you may only use replacement batteries of
Sütron electronic.
Electrostatic discharge can damage electronic components! Observe the ESD pro-
tective measures!
Do not throw lithium batteries into fire, do not heat to 100 °C or higher and do not
recharge. Danger - Explosive!
To ensure that the data in the SRAM and the time are preserved, it is possible to
change the battery under operating voltage. Observe the corresponding safety
notices!
1. Remove the screws on the rear of the device and lift off the enclosure cover.
2. Remove the cable fastener securing the battery.
3. Disconnect the connector from the battery and remove the dead battery.
4. Plug in the cable for the new battery.
5. Use a cable fastener to attach the new battery to the enclosure.
6. Place the enclosure cover back onto the device.
7. Carefully tighten the screws of the enclosure cover.
To prevent short circuitry in the collection boxes, insulate the poles of each battery
with insulation tape or put each single battery into a plastic bag.
You must always return old batteries to a dealer or to a returns depot set up for this
purpose by the public waste disposal body or a licensed battery dealer for recycling.
Only dispose of dead batteries in public or commercial collection boxes. The battery
is drained when the message „Change battery“ appears on the display of the opera-
ting device.
5-2
Technical Data
6 Technical Data
Display TP11AM TP11AT TP21AM TP21AS TP21AT
Type FSTN TFT (color) FSTN C-STN TFT (color)
(mono) (mono) (color)
Resolution (pixels) 320 x 240 320 x 240 320 x 240 320 x 240 320 x 240
Colors 5 Shades of 65536 5 Shades of 256 65536
gray gray
Reading angle 80° 140° 90° 60° 130°
Contrast setting Tempera- - Tempera- Tempera- -
ture compen- ture compen- ture compen-
sated sated sated
Half-life backlighting 30,000 h 30,000 h 30,000 h 40,000 h 50,000 h
Brightness in cd/m2 90 320 120 160 400
Display area (H x W) in 57.6 x 76.8 53.6 x 71.5 86.4 x 115.2 86.4 x 115.2 86.4 x 115.2
mm (Inch) (2.268 x (2.11 x (3.402 x (3.402 x (3.402 x
3.024) 2.815") 4.535) 4.535) 4.535)
6-1
Technical Data
Touch Screen
Type Analog resistive, 4 wire technology
Activation force 15 g (Standard)
With R8 HS60 silicon rubber
Durability No damages or malfunctions after 3 million keystrokes as the following:
Keystroke element: R8, HS40 silicon rubber
Keystroke load: 150 g
Keystroke frequency: 3 Hz
6-2
Technical Data
Ethernet
X5 Ethernet 10/100 Base-T
Serial Interfaces
Variable baud rates and data formats
X6 RS422 / RS485 In accordance with DIN 66259-4
Transmission length: 0 - 1200 m, twisted pair wire, shielded, galvanically iso-
lated
X6 RS232 In accordance with DIN 66259 T1, CCITT V.28
Transmission length: 0 - 15 m, conductors layered in strands, shielded,
galvanically isolated
6-3
Technical Data
USB
Corresponds to the "Universal serial bus specification Rev. 2.0“
X9, X10 Host Min.: 1.5 Mbit/s
Max.: 12 Mbit/s
Max. output current 100 mA per output
Connection System
D-SUB female and male connector strips, 9 pin and 25 pin
Female and male connector strips, Phoenix COMBICON, 3 pin
Male connector strip, Phoenix COMBICON, 5 pin
RJ45 female connector
USB female connector A
Environmental Conditions
Temperature during 0 °C to 50 °C (32 °F to 122 °F)
operation
Temperature during - 25 °C to + 70 °C (-13°F to + 158°F)
storage, transport
Relative air humidity for 20 % to 85 %, no condensation
operation and storage
Application area Degree of pollution 1, overvoltage category II
6-4
Technical Data
This is a class A device. This device may cause radio interference in residential ar-
eas. In this case, the user may be required to introduce appropriate countermea-
sures, and to bear the cost of same.
Approvals
CE, UL, cUL
6-5
Technical Data
6-6
Technical Data
6-7
Technical Data
6-8
Ordering Data
7 Ordering Data
Table 7-1 Accessories
7-1
Ordering Data
7-2
Index
A Index
A RS422 ....................................................... 4-6
RS485 ....................................................... 4-6
Accessories....................................................... 7-1
USB........................................................... 4-4
Administration operating mode ....................... 2-36
B L
Launcher
Battery............................................................... 5-1
Overview ................................................. 2-26
Battery disposal ................................................ 5-2
LcdBackLight..................................................... 3-1
Betriebsart Normal .......................................... 2-27
LcdContrast....................................................... 3-2
C Loading procedure on Windows CE operating sys-
Cable tem .................................................................. 2-25
CAN ........................................................ 4-10 M
DeviceNet ............................................... 4-14
Ethernet .................................................... 4-3 Maintenance...................................................... 5-1
INTERBUS.............................................. 4-17 Memory media used........................................ 2-38
MPI ......................................................... 4-20 Mounting ........................................................... 2-1
PROFIBUS-DP ....................................... 4-23 N
USB .......................................................... 4-4
Nameplate....................................................... 2-40
Changing the battery......................................... 5-2
Character attributes .......................................... 3-2 O
Connecting...................................................... 2-22
Ordering data .................................................... 7-1
D Overview
Launcher ................................................. 2-26
Device variants ................................................. 4-1
Diagnostics P
CAN ........................................................ 4-11
Pin assignment
DeviceNet ............................................... 4-15
CAN ........................................................ 4-10
Ethernet .................................................... 4-3
DeviceNet ............................................... 4-14
INTERBUS.............................................. 4-18
Ethernet .................................................... 4-3
MPI ......................................................... 4-21
INTERBUS.............................................. 4-17
PROFIBUS-DP ....................................... 4-24
MPI.......................................................... 4-20
Dimensions
PROFIBUS.............................................. 4-23
Cutout ....................................................... 2-8
RS232 ....................................................... 4-8
Front panel................................................ 2-2
RS422 ....................................................... 4-6
Display .............................................................. 3-1
RS485 ....................................................... 4-6
F R
Font
Rear view
Windows ................................................... 3-2
CAN Slave ................................................ 4-9
Function of the AppStarter.exe program......... 2-37
DeviceNet slave ...................................... 4-13
Function of the TSvisLD.exe program ............ 2-38
Ethernet .................................................... 4-2
Fuse .................................................................. 5-1
INTERBUS.............................................. 4-16
I MPI slave ................................................ 4-19
PROFIBUS-DP Slave ............................. 4-22
Identification.................................................... 2-40
RS422 / RS485 / RS232 ........................... 4-5
Important files and update .............................. 2-39
Important notes ................................................. 1-1
Intended use ..................................................... 1-2
Interface
CAN Slave ................................................ 4-9
DeviceNet slave...................................... 4-13
Ethernet .................................................... 4-3
INTERBUS Slave.................................... 4-16
MPI Slave ............................................... 4-19
PROFIBUS slave .................................... 4-22
RS232 ....................................................... 4-8
A-1
Index
S
Safety notes ...................................................... 1-2
Servicing ........................................................... 5-1
Setting the brightness ....................................... 3-1
Setting the contrast ........................................... 3-2
Setup Main operating mode ............................ 2-27
Standards.......................................................... 6-5
Supply voltage 24 V ........................................ 2-22
Switching on.................................................... 2-25
Symbols ............................................................ 1-1
General ..................................................... 1-1
Specific ..................................................... 1-1
T
Target group...................................................... 1-2
Technical data................................................... 6-1
Termination
CAN ........................................................ 4-11
DeviceNet ............................................... 4-15
MPI.......................................................... 4-21
PROFIBUS.............................................. 4-24
RS232 ....................................................... 4-8
RS485 ....................................................... 4-7
Touch screen .................................................... 3-3
U
Unpacking ......................................................... 2-1
V
Version key ..................................................... 2-40
A-2
Sütron electronic GmbH
Kurze Straße 29
D-70794 Filderstadt
Phone: 0049 711 / 77098-0
Fax: 0049 711 / 77098-60
E-Mail: doku@suetron.de
Internet: www.suetron.com