Академический Документы
Профессиональный Документы
Культура Документы
PART NUMBER
Gm625Od
Gm625Om4
Gm625Om5
Gm625Om6
MIDlAmR(bSS
Grimes Division
550 ROUTE 55/ Urbana, Ohio 43078
Tel. (513) 552.VW/TWX: 810457.2852/ Telex: 295439
33-41-41
Page T-l
Feb l/84
GRIMESDIVISION/MIDUND-ROSS CORPORATION
COMPONENTMAINTENANCEMANUAL
PARTNO. 66250
RECORD OF REVISIONS
Page RR-1
Feb l/84
GRIMESDIVISION/MIDUND-ROSS CORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. 66250
33-41-41
Page TR-1
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. 66250
SERVICEBULLETIN LIST
33-41-41
Page SBL-1
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANDAL
PARTNO. 66250
LIST OF EFFECTIVEPAGES
SUBJECT PAGE DATE
Title Page T-l Feb l/84
Record of Revisions RR-1 Feb l/84
Record of Temporary Revisions TR-1 Feb l/84
Service Bulletin List SBL-1 Feb l/84
List of Effective Pages LEP-1 Feb l/84
Table of Contents T/C-l Feb l/84
Introduction INTRO-l Feb l/84
Description and Operation 1 Feb l/84
2 Feb l/84
Testing and Trouble Shooting 101 Feb l/84
102 Feb l/84
103 Feb.l/84
104 Feb l/84
Disassembly 301 Feb l/84
302 Feb l/84
303 Feb l/84
'9Oi Blank_
Cleaning 401 Feb l/84
402 Blank
Check 501 Feb l/84
502 Blank
Repair 601 Feb l/84
602 Blank
Assembly and Storage 701 Feb l/84
702 Feb l/84
703 Feb l/84
704 Feb l/84
Illustrated Parts List 1001 Feb l/84
1002 Feb l/84
1003 Feb l/84
1004 Feb l/84
1005 Feb l/84
1006 Feb l/84
1007 Feb l/84
1008 Feb l/84
1009 Feb l/84
1010 Feb l/84
1011 Feb 1184
1012 Feb l/84
1013 Feb l/84
1014 Feb l/84
1015 Feb l/84
1016 Feb l/84
1017 Feb l/84
1018 Feb l/84
1019 Feb l/84
1020 Feb l/84
33-41-41
Page LEP-1
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMFONENTMAINTENANCEMANUAL
PARTNO. 66250
TABLE OF CONTENTS
33-41-41
Page T/C-l
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCEMANUAL
PART NO.iG6250
- .-_ .:,
INTRODUCTION
This manual contains shop instructions for testing, trouble shooting and repair
of the component listed on the cover page. The instructions are divided into
sections as shown in the table of contents.
These instructions only apply to the assembly model number shown on the cover
page. Ensure that the model number on the unit is listed on the cover page
before performing any instructions.
The procedures within this manual are only to be performed by qualified shop
mechanics who are familiar with this type of equipment.
The contents of this manual have been verified by the manufacturer prior to the
distribution of printed copies.
33-41-41
Page INTRO-l
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
DESCRIPTIONAND OPERATION
1. Description (Ref. Figure 1)
Landing and Search Light, part numbers 66250-1, 66250-4, 66250-S and 66250-6,
is used on aircraft to provide a directional beam of light, which is aimed
' manually by a remote control switch mounted in the cockpit. Positioning of
the light is achieved by extending and rotating the lamp to the desired
poeition. The extend and rotate motions are driven by two independent
motors, which are controlled by the remote control switch working through
internal relays. The lamp can be extended to any position from fully re
tracted (stowed), to approximately 120' from stowed position. It may be
rotated in either direction (left or right), a full 360° hontinously when
in any extend or retract poeition. The maximum extend is not adjustable.
The light requires a i-28 VDC power source with a ground (negative) return.
The lamp is manually turned off or on by a remote switch working through
-a relay contained in the light assembly,
33-41-41
Page 1
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENI!MAINTENANCEMANUAL
PARTNO. 66250
3. Leading Particulars
For leading particulars, refer to Figure 2.
Electrical requirements:
Input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 VDC
Dimensions (Inches):
Length . . . . . . . . . . . . . . . . . . ..a................. 12.12 max.
Width . . ..*.*.**....*..*.*......*......*..... 6.560 max.
Depth . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4.18 max.
Weight (pounds): . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5.65
Leading Particulars
Figure-2'
---
33-41-41~-_
.d Page 2
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
TESTINGAND TROUBLESHOOTING
1. Testing
A. Testing procedures for P/N 66250-l are as follows:
(1) With a +28 VDC power source, connect the negative lead to pin 1 of
terminal board TBl (Ref. Figure 101). Apply +28 VDC to pins 3 and
6. Relay R2 will close, applying voltage to motor B2 and the light
will extend until voltage to the motor is removed by switch Sl.
(2) With the light in the extended position, apply +28 VDC to pins
2, 3 and 5. Relay XC5will close and apply voltage to lamp DSl
causing it to illuminate. Relay K3 will close, applying voltage
to motor Bl, causing the light to rotate left.
(3) Remove voltage from pin 5 and apply +28 VDC to pin 4. Relay XC4
will close, applying voltage to motor Bl, causing the light to
rotate right.
(4) With the lamp at 0" rotation (switch S3 open), remove voltage from
pins 4 and 5. Apply voltage to pins 3 and 7. Relay IU will close, A
applying voltage to motor B2, causing light to retract until
voltage is removed from the motor by switch S2.
B. Testing procedures for P/N 66250-3, -4 and -5 are the same as for
P/N 66250-l with the following exceptions:
(1) Switch S4 is a lamp rotate switch that opens at left of right
go* 210 .
(2) Switch S5 is a lamp extend limit switch that is open 0' to 60' and
closed 60' to 120'.
33-41-41
Page 101
Feb l/84
GRIMESDIVISION/MIDIAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PARTNO. 66250
I
l!llH-- 1,
IIllli 1, f
f L. 0 -- -. B-B I -w-m--
p- .-a’) . 1'------
I I
. I
:
:23
i .a
SLIT\.
c---
I. 7II
- ._-- -- __.-
1
I
I
I
!
I
I
I
I
:
---r-d .
with an ohmmeter.
illuminate Defective --.relay _.-I Check relay winding Replace relay
with an ohmmeter.
to retract
Open switch S2 (5) Check switch with Replace switch.
an ohmmeter.
Defective motor Bench check motor. Replace motor
assembly (B2) (Ref. assembly.
40, IPL, Fig. 5)
Light fails Defective relay K4 Check relay winding Replace relay.
to rotate to (Ref. 45, IPL Fig. 3) with an ohmmeter.
the right
Defective motor Bench check motor. Replace motor
assembly Bl (Ref. assembly.
95, IPL Fig. 2) 1
---___---r
Light fails Defective relay K3 Check relay winding Replace relay.
to rotate to (Ref. 45, IPL Fig. 3) with an ohmmeter.
the left
Defective motor Bench check motor. Replace motor
assembly Bl (Ref. assembly.
95, IPL Fig. 2)
Trouble Shooting
Figure 102 (Sheet 1 of 2)
33-41-41
Page 103
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCE MANUAL
PART NO. 66250
Trouble Shooting
Figure 102 (Sheet 2 of 2)
33-41-41
Page 104
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE
MAiWAL
PART 66250
DISASSEMBLY
NOTE: See Testing and Trouble Shooting to establish the condition
of the component or the possible cause of its malfunction.
This is to determine the extent of disassembly required
without completely tearing down and rebuilding the component.
1. Disassemble Landing and Search Light
A. Loosen screws (Ref. 40, IPL Ffg. 1) and lift off retaining ring (35).
Disconnect and remove lamp (45) from canopy assembly (20).
B. Remove set screws (25) and separate canopy assembly (20) from rotate
mechanism (245).
c. Remove screws (Ref. 25, IPL Fig. 2) and plate (20).
D. Remove scre& (Ref. 75, IPL Fig. 1) and cover (70).
E. Remove screws (80 and 90), lock washers (85), insulator (95), reinforce-
ment strip (100) and U-channel (105).
F. Remove screw (LlS), lock washer (120) and clamp (110) from block (210).
G. Cut and remove miniature ties (125).
H. Remove screws (140), lock washers (145) and cover (130).
I. Remove screws (155), lock washers (160) and cover (150).
J. Remove screw (165) and lock washer (170). Separate contact arm assembly
(part of the wiring harness) from adjoining parts.
K. Remove screws (230), lock washers (235) and clamp (225).
NOTE: Keep wiring*harness (420) intact during --_-
disassembly
.--. .- .- and
_.- assembly
-- -.-...
procedures. Prior to separating switches and associated parts
of wiring harness, secure them together with tape to facilitate
reassembly, unless replacement of parts is required.
L. Remove screws (Ref. 20, IPL Fig. 3) and lock washers (25). Separate
actuator (30), insulator (35) and switches (5 and 15).
_-~ _-__ . -.. _-- -- -
M. Remove screws (Ref. 175, IPL Fig. 1), jflat washers (180) and lock washers._
(185). Removemounting plate (Ref. 40, IPL Fig. 3) and spacers (Ref.
15, IPL Fig. 2).
N. Remove screws (Ref. 195, IPL Fig. l), lock washers (200) and nuts (205).
33-41-41
Page 301
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
0. Place unit, base plate assembly (455) down, on a flat surface. With-
draw shaft and block assembly (consisting of items 210, 215 and 220) and
spacers (240).
P. Drive out roll pin (220) and separate block (210) and shaft (215).
Remove rotate mechanism (245). Refer to paragraph 2 for disassembly
procedures.
Q* Remove screws (260) and lock washers (265). Separate actuators (270 and
280) and insulators (275 and 290).
R. Remove screw (295), nut (300), flat washers (305), eyelet (310) and
spring (315). Eyelet (320) cannot be removed until gear box assembly
(435) is removed.
s. Remove screw (60), nut (65) and clamp (55).
T. Remove screws (330) and clip (325). Remove screw (345) and lock washer
(350). Remove cover assembly (335).
u. Remove screws (Ref. 50, IPL Fig. S), lock washers (45) and motor assembly
(40). Remove screws (Ref. 355, IPL Fig. 1) and nuts (360). Remove relay
assembly (Ref. 65, IPL Fig. 3).
v. Remove screws (Ref. 430, IPL Fig.1) and wiring harness (420). Remove
screws (385), lock washers (390) and relay box assembly (365) from wiring
harness (420). Drill out rivets (415) and remove name plate (395) from
relay box assembly (365) only if replacement is required.
w. Remove screws (440), lock washers (445), nuts (450) and gear box assembly
(435). Eyelet (320) will fall free. Refer to paragraph 3 for disassem-
bly procedures for gear box assembly (435).
2. Disassemble Rotate Mechanism
A. Spacer (Ref. 15, IPL Fig. 2), plate (20) and screws (25) have been
removed previously.
B. Remove screw (35), lock washers (40) and post (30).
c. Remove screw (SS), stud (50) and contact block (45).
D. Remove pivot shaft assembly (150) by sliding downward.
E. Remove screws (85), lock washers (90) and sector gear assembly (75).
F. Remove screws (65), lock washers (70) and actuator assembly (60).
G. Remove screws (loo), lock washers (105) and motor assembly (95).
* 33-41-41
Feb 1184 Page
- . - 302
,^.
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
8. Loosen set screws (115) and pull off helical gear (135). Slide out
worm gear assembly (110).
I. Remove bearings (120, 130, 140 and 145) and spacer (125) from casting
(160) only if replacement is required.
3. Disassemble Gear Box Assembly
A. Remove screws (Ref. 15 and 30, IPL Fig. S), lock washers (10 and 25),
relay housing (20) and bracket (5). Do not remove rivet (35) from
relay housing (20).
B. Motor assembly (40), lock washers (45) and screws (50) have been
removed previously.
C. Remove screws (65), lock washers (60) and gear cover (55).
D. Loosen set-screws (70 and 105) and remove bearing and end thrust adjust-
ment assembly (80), thrust bearing (85), worm and shaft assembly (90) and
worm wheel (100). Remove bearing (95) only if replacement is required.
E. Remove set screw (70) and insert (75) only if replacement is required.
F. Remove screws (120), lock washers (115) and bearing and bridge assembly
(110). Loosen set screws (130) and pull worm wheel (125) and woodruff
key (135) from pinion gear and shaft (140). Press out bearing (145)
from gear box assembly (160) only if replacement Is required.
G. Drill out shaft (155) only if it or bumper (150) must be replaced.
33-41-41
Page 303
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
, COMPONENT MAINTENANCE MANUAL
PART NO. 66250
CLEANING
1. Clean electrical parts with a clean, lint-free cloth moistened with isopropyl
alcohol, Federal Specification TT-I-735, or equivalent. Allow to air dry.
: SOLVENTAND ACETONEFUMESARE TOXIC. PROLONGED
WARNING INHAUTION
OF TRE FUMESMAYCAUSEILLNESS.
2. Clean metal parts with dry cleaning solvent, Federal Specification P-D-680,
or equivalent.
3. Clean the lamp with acetone, Federal Specification O-A-51, or equivalent.
33-41-41
l%b 1/S+ Page 401
W-L q lOI
GRIMESDIVISION/MIDIAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. 66250
1. Inspect wiring harness (Ref. 420, IPL Fig. 1) for broken leads and defective
insulation. Check operation of all limit switches and relays.
2. Visually inspect lamp (45) for cracks or fogging of reflector (that indicates
cracks in lamp).
3. Inspect condition of sector gear assembly (Ref. 75, IPL Fig. 2).
4. Inspect all gears, worm gears and worm wheels for broken teeth and wear.
5. Inspect all metal parts for damage or distortion.
33-41-41
Page 501
Feb l/84
GRIMESDIVISION/MIDLANP-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
REPAIR
Repair consists of replacing parts determined defective during CHECK,TESTING
and TROUBLESHOOTING.
33-41-41
Feb l/e+ Page 601
lnh 1 tar.
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
G. Install contact block (45) on casting (160) and secure with stud (50) and
screw (55).
H. Install post (30) on casting (160) and secure with screw (35) and lock
washer (40).
I. Install spacers (15) in casting (160).
J. Plate (20) and screws (25) will be Installed at final assembly.
2. Assemble Gear Box Assembly
A. If previously removed, press bearings (Ref. 95 and 145, IPL Fig. 5) into
gear box assembly (160).
B. Place pinion
- --. ~~gear and shaft assembly (140) into gear box assembly (1609,
install woodruff key (1359, place worm wheel (125) onto shaft and secure
with set screws (130).
__.
c. Install bearing and bridge assembly (110) and secure with screws (120)
and lock washers (115).
D.. Install worm and shaft assembly (909, thrust bearing (85) and worm wheel
(100). Secure worm wheel (100) with set screws (1059..
33-41-41
Feb 4184 Page 701
T-n-L. Inr
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
E. Install bearing and end thrust adjustment assembly (80) and secure With
insert (75) and set screw (70).
F. Install gear cover (55) and secure with screws (65) and lock washers
(60).
G. If previously removed, install bumper (150) and shaft (155) on gear box
assembly (160). Flair end of shaft (155) to secure.
H. Attach bracket (5) to gear box assembly (160) with lock washers (10) and
screws (15).
I. Attach relay housing (20) to gear box assembly (160) with lock washers
(25) and screws (30). Rivet (35) should not have been removed from
relay housing (20).
J. Install motor assembly (40) on gear box assembly (160) and secure with
lock washers (45) and screws (SO).
30 Assemble Landing and Search Light
A. Position relay assembly (Ref. 65, IPL Fig. 3) in gear box assembly (Ref.
435, IPL F&g. 1) and secure with screws (355) and nuts (360).
B. Attach clip (325) to cover assembly (335) with screw (330). Install
cover assembly (335) and secure with lock washer (350) and screw (345).
c. Insert screws (260) and lock washers (265) through actuator (270),
switches (Ref. 5, IPL Fig. 3), separated by insulator (Ref. 275, IPL
Fig.l), actuator (280) and insulator (290) and secure to gear box assem-
bly (435).
D. Route wiring harness (420) under gear box assembly (435) through slot In
outboard side.
E. Attach gear box assembly (435) to base plate assembly (455) with screws
(440), lock washers (445) and nuts (450).
F. Install screw (295) through base plate assembly (455) and eyelet (320).
Position flat washers (305), spring (315) and eyelet (310) over screw
(295) and 'secure with nut (300).
G. Position clamp (55) on base plate assembly (455) and secure with screw
(60) and nut (65).
H. Insert shaft (215) into block (210) and secure with roll pin (220).
Place one spacer (240) over shaft (215) and insert shaft (215) through
rotate mechanism (245). Place the remaining spacer (240) over opposite
end of shaft (215).
33-41-41
Page 702
Peb 1 /Fib
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
Q* Install screws (80 and 90) and lock washers (85) through terminal block
(Ref. 85, IPL Fig. 3), insulator (Ref. 95, IPL Fig. 1) and reinforcement
strip (100). Secure to base plate assembly (455) with screws (80 and
90).
R. Install cover (70) and secure with screws (75).
s. Position cover (130) on gear box assembly (435) and secure with screws
(140) and lock washers (145).
T. Secure wires to motor assembly (Ref. 95, IPL Pig.2) with miniature ties
(Ref. 125, IPL Fig. 1).
u. Install plate (Ref. 20, IPL Fig. 2) and secure with screws (25).
V. Apply No. 88 sealant, manufactured by Loctite Corp., Newington CT.
to threads of set screws ((Ref. 25, IPL Fig. 1). Install canopy
assembly (20) and secure with set screws (25).
33-41-41
Page 703
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANDAL
PARTNO.:66250 -
.
w. Install lamp (45) in canopy assembly (20) and secure with ring retainer
(35) and screws (40).
STORAGE
1, Wrap the ~--
Landing and Search Light with cushioning material, Military Speci-
fication,MIL-C-81013. r
2, Enclose the assembly and desiccant, Military Specification MIL-D-3464, in
heat sealable film, Military Specification MIL-P-22191, and seal the film
using a sealing iron, Military Specification MIL-S-43336.
3, Store the assembly in an area with a temperature range of -65*F to +16O*F.
33-41-41
Page 704
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONRNTMAI~NANCRMANUAL
PART NO.,G6250
ILLUSTRATEDPARTSLIST
1. Introduction
A. The Illustrated Parts List is a breakdown of assemblies, and detail parts
of the assembly. Index numbers on the exploded view illustration
accompanying the parts list indicate the general order of disassembly.
Component parts are indented to show subordinate relationship to the
complete assembly.
B. The Units Per Assembly column of the parts list indicates the quantity of
each part required for the next higher assembly.
c. Part numbers and description in the parts list identify each part. The
index numbers in the parts list refer to the accompanying exploded view
illustration.
D. Part numbers in this list are those of Grimes Division/Midland Ross
Corporation, unless a vendor code number follows the part nomenclature.
Standard numbers are prefixed as follows:
AN -Y- Navy Standard
MS Military Standard
NAS National Aerospace Standard
E. When an equipment designator has been assigned to an item, the designator
will be shown in parentheses following the description of the part.
F. Symbols used, with the exception of effectivity, equipment designator,
and vendor code symbols are as follows: *** designates the end of each
group of attaching parts.
G. Part numbers of vendors are shown in the Part Number column whenever
applicable. The vendor code number is shown in parentheses following the
description of the part. This code number Is prefixed with a capital
letter V.
H. The following is a compilation of the vendor codes with the names and
addresses of suppliers for purchased parts used in this illustrated parts
list.
33-41-41
Page 1001
Feb l/84
GRIMESDIVISION/MIDLANI+ROSSCORPORATION
COMPONFJT MAINTENANCE MANUAL
PART NO. 66250
33-41-41
Page 1002
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. 66250
n. - :/ri!iI “y
‘\
ki\ 20
=B-p!vi
qrk ;/ -25
a ,
.‘I 125
130 - . 270+& --
FF- ,240
245
\ 275*
/
225
,235
1w-“= -%"230
d?5300 ,
350y55 A’60
I
205
I
EFF UNITS
FIG. AIRLINE NOMENCLATURE CODE PER
ITEM PARTNUMBER PART NO. 1234567 ASSY
1 -1 66250-l LIGHT, LANDINGAND SEARCH A RF
Q-5 66250-4 LIGHT, LANDINGAND SEARCH B RF
-10 66250-S LIGHT, LANDINGAND SEARCH C RF
-15 66250-6 LIGHT, LANDINGAND.SEARCH D RF
20 46-0970-l . CANOPYASSEMBLY 1
ATTACHINGPARTS
25 AN565D6H3
-_-- : . SCREW,SET 2
***
-30 46-0972-l .LAMP RETAINERASSEMBLY 1
35 B6702 . . RING, RETAINER 1
40 Ms24693S31 . . SCREW,MACHINE 3
45 4580 a LAMP, 28 V, 450 W (DSl) A,B,C 1
(VOSSOS)(Grimes
Stock Code GE4580)
-50 lfskwk458_2- . LAMP, 28 V, 450 W (DSl) D 1
55 26479-l .CLAMP 1
ATTACHINGPARTS
60 Ms24693S3 . SCREW,MACHINE 1
65 MS21044NO4 . NUT, HEX 1
***
70 A6881 .COVER 1
ATTACHINGPARTS
75 MS35206-232 . sCRFiw,MACH1NE 2
***
80 MS35206-226 . SCREW,MACHINE 1
85 MS35338-41 . WASHER,LOCK 1
90 MS35206-230 e SCREW,MACHINE 1
95 A7998 . INSULATOR 1
100 A7806A-4 . STRIP,REINFORCEMENT 1
105 X538 . U-CHANNEL(V70485) (Grimes 1
Stock Code MISC142)
110 26479-l .CLAMP 1
ATTACHINGPARTS
115 MS35206-213 . SCREW,MACHINE 1
120 MS35338040 e WASHER,LOGIC 1
***
%25 MS3367-1-9 . TIE, MINIATURE 2
I.30 B6938 a COVER A 1
-135 46-0339-l . PLATE, IDENTIFICATION B,C,D 1
ATTACHINGPARTS
140 SC657 . SCREW,MACHINE2-56 x l/4 4
IN LG, SLOT, RD HD,
STL,TYPE F
I.45 MS35333-35 .WASHER,LOCK 4
***
EFF UNITS
FIG. AIRLINE NOMENCLATURE CODE PER
ITEM PART NUMBER PART NO. 1234567 ASSY
1 150 B6908-1 . COVER 1
ATTACHINGPARTS
155 MS35206-213 . sCREw,MACE1NE 2
160 MS35338-40 . wAsHER,LocK 2
***
165 Ms35206-213 . sCREw,MACH1NE 1
170 MS35338040 . WASHER,LOCK 1
175 MS35206-221 . SCREW,MACHINE 2
180 MS2718304 .WASHER, FLAT 1
185 MS35338040 . WASHER,LOCK 2
-190 46-0968-l . SHAFTAND BLOCKASSEMBLY 1
ATTACHINGPARTS
195 Ms24693S28 . sCREw,MACEmm 2
200 MS35338041 c . . WASHER,LOCK 2
205 NAS671-6 . NUT, HEX 2
***
210 &KiG.~9~ . . BLOCK 1
215 A6928 . SHAFT 1
---.- &ACHING PARTS.._
220 790022-094- : . . PIN, ROLL (q72962)
.-.- 1
0625 (Grimes Stock
Code PN295)
225 A6927 .CLAMP 1
ATTACHINGPARTS
230 MS35206-213 . SCREW,MACHINE 2
235 Ms35338-40 .WASHER,LOCK 2
***
240 A6926 . SPACER 2
245 46-0966-9 . ROTATEMECHANISM A 1
(See IPL Fig. 2
for details)
-250 46-0966-l . ROTATEMECHANISM B 1
(See IPL Fig. 2
for details)
-255 46-0966-15 .ROTATEMECHANISM C,D 1
(See IPL Fig. 2
for details)
260 MS35206-209 . SCREW,MACHINE 2
265 MS35333035 . WASHER,LOCK 2
270 A6948 . ACTUATOR 1
275 A6939 . INSULATOR 1
280 A6947 . ACTUATOR A,B 1
-285 A694703 . ACTUATOR C,D 1
290 A%!? ~_.~ . INSULATOR 1
295 -kS24693S34
.- ___._- _ . sCREw,MmmlE 1
EFF UNITS
FIG AIRSSNE NOMENCLATURE CODE PER
ITEM PART NUMBER PARTNO. 1234567 ASSY
1 300 MS21044NO6 . NUT, HEX 1
305 AN960-10 . WASHER,FLAT 2
310 E3462 . EYELET (V19104) (Grimes 1
Stock Code EY540)
315 A6946 . SPRING 1
320 A375202 .EYELET 1
325 10811 . CLIP B,C,D 1
ATTACHINGPARTS
330 MS352060214 .SCREW,MACHINE B,C,D 2
***
335 A687805 . COVERASSEMBLY A 1
-340 46-0007-l . COVERASSEMBLY B,C,D 1
ATTACHINGPARTS
345 SC644 . SCREW,MACHINE,2-56 x 1
3/16 IN LG, SLOT, RD EID
STL,TYPE I
350 MS35333035 . WASHER,LOCK 1
***
355 'MS35206-215 . SCREW,MACRINE 2
360 MS21044NO4 . NUT, HEX 4
365 86535-l . B.ELAYBOXASSEMBLY A 1
-370 B6535-11 .RELAY BOXASSEMBLY B 1
-375 B6535-12 . RELAY BOXASSEMBLY C 1
-380 B6535-13 . RELAYBOXASSEMBLY D 1
ATTACHINGPARTS
385 MS352060234 . SCREW,MACHINE 2
390 MS35338041 .WASHER, LOCK 2
***
395 B6545-2 . . PLATE,NAME A 1
-400 B6545-5 . . PLATE,NAME B 1
-405 B6545-7 . . PLATE,NAME C 1
-410 B6545-8 .PLATE,NAME D 1
LTACHING Pars
415 MS2047OA2-3 RIVET 2
;*;
420 46-0978-3 . HARNESS,WIRING A 1
(See IPL Fig. 3
for details)
-425 46-0978-l . HARNESS,WIRING B 1
(See IPL Fig. 4
for details)
-4258 46-0978-11 . HARNESS,WIRING C,D 1
(See IPL Fig. 4
for details)
ATTACHINGPARTS
430 MS24693S26 . SCREW,MACHINE 2
***
EFF UNITS
FIG. AIRLINE NOMENCLATURE CODE PER
ITEM PART NUMBER PART NO. 1234567 ASSY
33-4-l-41
Page 1007
" Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION '
c0MF0NEmMA1NTFmANCEMmJAL
PARTNO. 66250
1 J 135
w- (
9’
41 13n
Ii0
33-41-41
Fd 4/e4 Page 1008
77-t . In,
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
EFF UNITS
XG. AIRLINE NOMENCLATURE CODE PER
CTEM PART NUMBER PARTNO. 1234567 ASSY
.' -1 46-0966-g ROTATE MECHANISM A RF
(See IPL Fig. 1 for NRA)
-5 46-0966-l ROTATEMECHANISM B RF
(See IPL Fig. 1 for NHA)
-10 46-0966-15 ROTATEMECHANISM C,D RF
(See IPL Fig.1 for NRA)
15 60-3004A4B0656 . SPACER 2
20 6915 . PLATE 1
ATTACHINGPARTS
25 MS24693S3 . sCREw,MACEm?E 2
***
30 A6918 . POST 1
ATTACHINGPARTS
35 MS35206-217 - . . SCREW,MACHINE 1
40 MS35338-40 . WASHER,LOCK 1
***
45 A6909 . BLOCK, CONTACT 1
ATTACHINGPARTS
50 A6913 . STUD 1
55 MS352060219 . SCREW,MACHINE 1
***
60 46-0992-l . ACTUATOR ASSEMBLY 1
ATTACHINGPARTS
65 MS35206-213 . SCREW,MACHINE 2
70 Ms35338-40 . WASEER,LOCK 2
***
75 B6921-1 . GEARASSEMBLY,SECTOR A,B 1
-80 B6921-3 . GEARASSEMBLY,SECTOR C,D 1
ATTACHINGPARTS
85 MS24693S28 .SCREW,MACHINE 2
90 MS35790-1 . WASHER,LOCK 2
***
95 46-0957-3 . MOTORASSEMBLY(Bl) 1
ATTACHING PARTS
100 MS35206-215 . sCREw,MACFl1NE 2
105 MS35338040 . WASHER,LOCK 2
***
110 A6588 . GEARASSEMBLY;WORM 1
ATTACHINGPARTS
115 AN565D6H3 . SCREW,SET 2
***
120 A6943 . BEARING 1
125 A7799 . SPACER 1
130 A6873 . BEARING 1
135 A6595 .GEAR,EELICAL 1
140 A6919A . BEARING 2
33-41-41
Page 1010
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
. COMPONENTMAINTENANCEMANUAL
PART NO. 66250
Wiring Harness - Pictorial View'
IPL Figure 3
33-41-41
Page 1011
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONFXC MAINTENANCE MANUAL
PART NO. 66250
EFF UNITS
PIG. AIRLINE NOMENCIATURE CODE PER
CTEM PARTNUMBER PARTNO. 1234567 ASSY
3 -1 46-0978-3 HARNESS,WIRING A RF-
(See IPL Fig. 1 for NM)
5 1sMl . SWITCH, SPDT (Sl,S2) A 2
(V91929) (Grimes
Stock Code SW538)
10 A6912 . CONTACTARMASSEMBLY A 1
15 1sMl . SWITCH, SPDT (S3) A 1
(V91929) (Grimes
Stock Code SW538)
ATTACHINGPARTS
20 55-0206-S . SCREW,MACHINE2-56 x 3/8 A 2
IN LG, SLOT PAN HD, STL
25 MS35333035 .WASEERp LOCK A 2
***
30 13257 . ACTUATOR A 1
35 A6939 z-INSULATOR A 1
40 A6916 . P-e, MOUNTING
.- // A 1
45 Al00739 . RELAY (Kl,K2,K3,K4) A 4
(V71482) (Grimes
Stock Code RL350)
ATTACHINGPARTS
50 Ms35206-226 . sCREW,uACH1NE A 8
55 MS35338041 . WASHER,LOCK A 8
***
60 32483 . BOX A 1
65 46-0962-l .RELAY ASSEMBLY(K5) A 1
70 31881 . TERMINAL(VO0779) (Grimes A 6
STOCKCODETEO87)
75 32442 . TERMINAL(VOO779) (Grimes A 1
Stock Code TE195)
80 MS3548904 . GROMMET __--- A 2
85 A690601 . BLOCK, TERMINAL(TBl) A 1
33-41-41
Page 1012
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. G6250
Wiring Harness - Pictorial View
IPL Figure 4
33-41-41
Page 1013
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENT MAINTENANCE MANUAL
PART NO. 66250
EFF UNITS
FIG. AIRLINE NOMENCIATURE CODE PBR
ITEM PART NUMBER PARTNO. 1234567 ASSY
4 -1 46-0978-l HARNESS,WIRING B RF
(See IPL Fig. 1 for NRA)
-1A 46-0978-11 HARNESS,WIRING C,D RF
(See IPL Fig. 1 for NRA)
5 1sMl . SWITCE, SPDT (Sl,S2) B,C,D 2
(V91929) (Grimes
Stock Code SW538)
10 A6912 . CONTACTARMASSEMBLY B,C,D 1
15 1sMl . SWITCH, SPDT (S3,S4) B,C,D 2
(V91929) (Grimes
Stock Code SW538)
ATTACHINGPARTS
20 MS352060209 . scREw, MACHINE B,C,D 2
25 I!@35333035 o WASHER,LOCK B,C,D 2
***
30 13257 . ACTUATOR - B,C,D 2
35 A6939 . INSULATOR B,C,D 2
40 A6916 . PLATE, MOUNTING B,C,D 1
45 1SXlT . SWITCH, SPDT (SS) B,C,D 1
(V91929) (Grimes
Stock Code SW5401)
ATTACHINGPARTS
50 55-0208-13 . SCREW,MACHINE2-56 x B,C,D 2
7/16 IN LG, 82 SLOT
PANrn,STL
55 MS35338039 .WASHER,LOCK B,C,D 2
60 MS356490222 . NUT, HEX B,C,D 2
***
-6OA 46-0005-l . ACTUATOR B,C,D 1
65 46-0004-l .BRACXET B,C,D 1
70 Al00739 . RELAY (Kl,K2,K3,K4) B,C,D 4
(V71482) (Grimes
Stock Code RL350)
ATTACHINGPARTS
75 MS352060226 . SCREW,MACHINE B,C,D 8
80 MS3533841 . WASHER,LOCK B,C,D 8
***
85 32483 . BOX B,C,D 1
90 46-0962-l e RELAYASSEMBLY(X5) B,C,D 1
95 31881 . TERMINAL(VOO779) (Grimes B,C,D 6
Stock Code TEO87)
100 32442 . TERMINAL(VOO779) (Grimes B,C,D 1
Stock Code TE195)
105 MS35489-4 . GROMMET B,C,D 2
110 A690601 . BLocic, TERMINAL(TB~) B,C,D 1
65
33-41-41
Page 1015
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCOBFOBATION
COMFONENTMAINTENANCE MANUAL
PART NO. 66250
EFF UNITS
"IG. AIRLINE NOMENCLATURE CODE PER
:TEM PARTNUMBER PART NO. 1234567 ASSY
i -1 46-0965-l GEARBOXASSEMBLY RF
(See IPL Fig. for NHA)
5 13263 .BRACXET 1
ATTACHINGPARTS
10 MS35338041 . WASHER,LOCK 1
15 MS35206-226 . SCREW,MACHINE 1
***
20 A6879-7 . HOUSING,RELAY 1
ATTACHINGPARTS
25 MS35333937 . WASHER,LOCiC 2
30 MS35206-226 . sCREw,MACH1NE 2
***
35 RVO60 . RIVET, 0.062 DIA x l/8 1
IN LG, UNIV HD, AL
40 46-0956-3 . MOTORASSEMBLY(B2) 1
ATTACHINGPARTS
45 MS35338040 .WASHER,LOCX 2
50 MS35206-216 . SCREW,MACHINE 2
***
55 46-0732-l . COVER,GEAR 1
ATTACHINGPARTS
60 MS35338-41' . WASHER,LOCK 2
65 MS35206-226 . SCREW,MACHINE 2
***
70, AN565D6H3 . SCREW,SET 1
75 A8552A2 . INSERT 1
80 A7798 . BEARINGAND END THRUST 1
ADJUSTMENT ASSEMBLY
85 FTOl . BEARING, THRUST(V76875) 1
(Grimes Stock Code BE200)
90 A6585A . WORMAND SHAFTASSEMBLY 1
95 A6873 . BEARING 1
100 A6582 . WHEEL,WORM 1
ATTACHINGPARTS
105 AN565D6H3 . SCREW,SET 2
110 A6954 . BEARINGAND BRIDGEASSEMBLY 1
ATTACHINGPARTS
115 MS35338041 .WASHER,LOCX 2
120 MS35206-228 . SCREW, MACHINE 2
***
125 A6580 . WHEEL,WORM 1
ATTACHINGPARTS
130 AN565DbH4 . SCREW,SET 2
***
135 MS35756-1 . XEY, WOODRUFF 1
EFF UNITS
FIG. AIRLINE NOMENCLATURE CODE PER
ITEM PART NUMBER PARTNO. 1234567 ASSY
/5 140 A6573 .GEARAND SHAFTASSEMBLY, 1
PINION
145 A694401 . BEARING 1
' 150 A6934 .BUMPER 1
i 155 A6933 . SHAFT 1
1 160 D6903-9 . BOXASSEMBLY,GEAR 1
A
- Items not illustrated
33-41-41
Page 1017
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PARTNO. 66250
NUMERICALINDEX
Part Number
Airline IPL
Part No. Fig. Item
1
iii
Req
-
Part Number
Airline IPL
I
TTL
Part No. Fig. 1telnReq
1
AN565D6H3 25 7 A6947 280 1
2 115 --- A6947-3 1 285 1
5 70 A6948 1 270 1
5 105 A6954 5 110 1
AN565D6H4 5 130 2 A7798 5 80 1
AN960-10 1 305 2 A7799 2 125 1
A100739 3 45 8 A7806A-4 1 100 1
4 70 A7998 1 95 1
A2728-3 2 145 A8552A2 5 75 1
A3752-2 1 320 B6535-1 1 365 1
A6573 5 140 B6535-11 1 370 1
A6580 5 .125 B6535-12 1 375 1
A6582 5 100 B6535-13 1 ?80 1
A6585A 5 90 B6545-2 1 395 1
A6588 2 110 B6545-5 1 400 1
A6595 2 135 B6545-7 1 405 1
A6873 2 130 B6545-8 1 410 1
5 95 B6702 1 35 1
A6878-5 1 335 B6908-1 1 150 1
A687907 5 20 B6921-1 2 75 1
A6881 1 70 B6921-3 2 80 1
A6901-9 1 210 B6938 1 130 1
A6906-1 3 85 D6903-9 5 160 1
4 110 'E3462 1 310 1
A6909 2 45 1 FTOl 5 85 1
A6912 3 10 2 66250-l 1 1RF
4 10 ,G6250-4 1 SRJ?
A6913 2 50 1 66250-S 1 10 RF
A6916 13 40 2 G6250-6 1 15 RF
4 40 ~66528 2 160 1
A6918 MS2047OA2-3 1 415 2
A6919A ~; 3o
140 MS21044N04 1 65 5
A6926 ~1 240 1 360
A6927 225 bfS21044N06 1 300 1
A6928 215 1MS24693S3 1 60 3
A6932 :i 290 2 25
A6933 155 MS24693S26 1 430 2
A6934 ~; 150 MS24693S28 1 195 6
A6939 1 275 1 440
3 35 2 85
4 35 Ms24693S31 1 40 3
A6943 2 120 MS24693S34 1 295 1
A6944-1 5 145 MS27183-4 1 180 1
A6946-1 1 315 MS28926-4582 1 50 1
*
33-41-41
iGb d/g+ Page 1018
l?-L , Iat.
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. G6250
NUMERICALINDEX (CONTINUED)
Airline :PL iii Airline IPL
Part Number Part No. 'ig. Item bq Part Number Part No. Fig. Item Req
-
MS3367-l-9 1 125 2 KS35338-41 3 55
MS35206-209 1 260 4 (Cont'd) 4 80
4 20 5 10
MS35206-213 1 115 8 5 60
1 155 ----_ _ 5 115
1 165 !fS35489-4 3 80 4
1 230 4 105
2 65 KS35649-222 4 60 2
MS35206-214 1 330 2 MS35756-1 5 135 1
MS35206-215 1 355 4 Ks35790-1 2 90 2
2 100 NAS671-6 1 205 4
M!Z35206-216 5 50 2 1 450
MS35206-217 2 35 1 RVO60 5 35 i
Ks35206-219 2 55 1 SC644 1 345 1
MS35206-221 1 175 2 SC657 1 140 4
MS35206-226 1 80 22 X538 1 105 1
3 50 1SMl 3 5 7
4 75 3 15
5 15 4 5
5 30 4.
5 65 1SXlT 4 ;; 1
MS35206-228 5 120 2 10811 1 325 1
MS35206-230 1 90 1 13257 3 30 3
MS35206-232 1 75 2 4 30
MS35206-234 1 385 2 13263 5 5 1
MS35333-35 1 145 11 26479-l 1 55 2
i 265 1 110
1 350 31881 3 70 12
25 4 95
2 25 32442 3 75 2
MS35333-37 5 25 2 4 100
MS35338-39 4 55 2 32483 3 60 2
MS35338-40 1 120 15 4 85
1 160 4580 1 45 1
1 170 46-0004-l 4 65 1
1 185 46-0005-l 4 6OA 1
1 235 46-0007-l 1 340 1
2 40 46-0339-l 1 135 1
2 70 46-0732-l
--._.- -. 5 55 1
2 105 46-0851-7' 1 455 1
5 45 46-0946-l 2 155 1
MS35338-41 1 85 28 46-0946-s 2 150 1
1 200 46-0956-3 5 40 1
1 390 46-0957-3 2 95 1
1 445
-
33-41-41
Page 1019
Feb l/84
GRIMESDIVISION/MIDLAND-ROSSCORPORATION
COMPONENTMAINTENANCEMANUAL
PART NO. 66250
l 33-41-41
Page 1020
Feh 1/8L