Академический Документы
Профессиональный Документы
Культура Документы
Mechanical specifications
Beam B
10 10
3 47° 3
continuously adjustable
1850 – 1990 MHz
45° Wind load N | lbf Frontal 710 | 160
Beam A (at Rated Wind Lateral 200 | 45
(–30°) 7.1° Speed: 150 km/h) Rearside 820 | 184
Max. Wind Velocity km/h 200
10
Beam B
10
mph 124
(+30°) Height / Width / Depth mm 1314 / 380 / 150
dB
dB
3 45° 3
inches 51.7 / 15.0 / 5.9
Horizontal Pattern Vertical Pattern
936.4885/a
for 42 – 115 mm |
(+30°) 1.7– 4.5 inches diameter
dB
dB
3 43° 3
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Accessories
General Information
1314 | 51.7
1484 | 58.4
1514 | 59.6
Please note: The dual-beam antenna must not be used in combination with any downtilt kit.
Grounding: The metal parts of the antenna including the mounting kit and the inner
conductors are DC grounded.
Correlation Table
Frequency range Array
Adjustment
1710 – 2200 MHz B1 Beam B mechanism
1710 – 2200 MHz B2 Beam A with integrated scale
All dimensions
in mm | inches
B1 B2
Left Right
Layout of interface:
57 | 2.2
| 4.7
120
.0
|2
50
135 | 5.3
150 | 5.9
Subject to alteration.
936.4885/a
380 | 15.0
Bottom view
300° 6 60°
10
20
270° 90°
Antenna II
Antenna III
Left
Right
240° 120°
Antenna I
m
0 t
47 Dou
m
Bottom view
For the above 3 Panel Arrangement please use the 3 Sector Clamp Kit 742034 (order separately).
3 Panel Arrangement
Mechanical specifications
Weight kg 60
lb 132.3
Wind load N | lbf Frontal 950 | 214
(at Rated Wind Lateral 950 | 214
Speed: 150 km/h) Rearside 950 | 214
Max. Wind Velocity km/h 200
mph 124
Subject to alteration.
936.4885/a
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
Mounting Hardware
Clamp Included in the Scope of Supply
152 [5.98]
100 [3.94]
[0.79–0.98]
40 [1.57]
72 [2.83]
20–25
40 [1.57]
15
2–1
4 4.53]
5–
[1.6
M10 MA = 25 Nm
M8 MA = 20 Nm
35 [1.38]
64 [2.52]
125 [4.92]
20–25
[0.79–0.98]
Subject to alteration.
936.3920/c
Please note: Kathrein does not recommend to use counter nuts. All dimensions in mm and [inches]
The additional nuts supplied are only meant as spares.
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Adjustment Mechanism
1
2
2
➀ Twist protection. ➀ Thread for fixing the protective To set the downtilt angle exactly,
➁ Downtilt spindle with integrated cap or the RCU (Remote Control you must look horizontally at the
scale. Unit). scale. The lower edge of the gear-
➁ Gearwheel for RCU power drive. wheel must be used for alignment.
0° – max.°
0° – max.°
Remove the protective cap and the Set downtilt angle by rotating the Screw on the twist protection and
twist protection completely. gearwheel. the protective cap again.
For a description of RCU installation please refer to the respective data sheet.
All specifications are subject to change without notice.
The latest specifications are available at www.kathreinusa.com Page 1 of 2
Kathrein USA Greenway Plaza II, 2400 Lakeside Blvd., Suite 650, Richardson TX 75082
Phone: 214.238.8800 Fax: 214.238.8801 Email: info@kathrein.com
General Instructions
for Feederline and RCU Installation
for Antennas
Please note: In order not to damage the interfaces, please make sure that only the right tools are used.
Tighten the feederline connector interfaces solely by using a common torque-wrench with a suitable wrench
width.
Adjustment mechanism
(protective cap removed) Ventilation hole
Colour coding:
Correlation of each RF input to:
– the corresponding adjustment mechanism
7-16 female (long neck) – the frequency range
– the polarization
32 | 1.3
Subject to alteration.
guidelines).
| 1.
1
These tools are suitable for 7-16 connectors with a wrench size of
27 or 32 mm | 1.1 or 1.3 inches, and the RCU attachment nut with a
wrench size of 41 mm | 1.6 inches.
Tighten nuts within a torque range of 25 – 33 Nm depending on
connector manufacturers’ specifications, respectively the RCU nut
with a torque range of 15 – 18 Nm.