Академический Документы
Профессиональный Документы
Культура Документы
The Message
regarding unrecognized hard drive is a bit misleading, because the SONOS has no such ( the only
"conventional" disk would be the MOD for digital image storage, a lack of interference
Of course, what the system lacks can easily be found via a test program. I do not have
more the logon and password structure of these systems, but which can any ultrasound service
Employees here in NRW on the basis of the serial number you give, because they have on their
notebook the matching passwpord generator (on a picture, the SN is indeed documented). To
correctly logging in the test window, just run the full test. The system complains
the affected component already accurate! It can not be bad, there is always a "kind of picture"
is still shown. Maybe only a loose board or a mistake in the frontend. You can, if
frontend components are suspect, the 4 frontend boards behind the transducer plugs
exchange with each other and observe the effect (the two middle need the system for
So I would proceed:
1) Start self-test
3) Check all boards for a clean fit and especially the ribbon cables in the E-Box,
Bad luck, if it's the memory board (the board in the backend, the scanconverter, the as
Cache for all image data is used, but also reports reliably the self-test), because
that would have to be exchanged then. But is an extremely rare mistake, I have in my career
Hello again,
another small supplement to my first answer: in the event that this system is
a fully featured thing, so a live 3D echo machine, could also be the system error
have to do with the integrated 3D PC. Of course, this is not the case for normal 2D operation
necessary, but a fault would also be reported. The green lamp on the PC below in
System must shine, if it is red, did not boot the thing clean, then 3D does not work. If here
there is a problem, please report again, you can "reanimate" the PC (runs on windows XP
). But first press "reset", restart and, if necessary, the complete self-test
let nip ... ..
the test diagnoses at the SONOS have almost 100% hit rate!
Hello,
when the 3D PC actually goes on strike, there can actually be only two causes as an alternative.
Very
Probably the button cell in the PC, which hold the back-up voltage ready to boot into the BIOS
should have arrived at the end of her lifetime. Can also be that when too slow boot process
Most likely, only the BIOS battery in the 3D PC is in the bucket. The change is as follows:
Pull lower drawer out of the system (may have a spring stop halfway)
on the side, push in and pull out completely until you get to the PC back), the PC lid
Take off with a few screws, then the view is clear on the battery, a button cell in the
left half of the PC's type R2032 (has every household department at EDEKA or so). battery
change and switch on the system. With luck, everything runs smoothly. That's actually the one
Normally.
If 3D is not activated after a few minutes (the green lamp on the PC must be lit!)
Proceed as follows:
a) Before switching on the mouse and keyboard on the PC install (all connections are on the
Rear panel, upper connector is reserved for the mouse, lower for the keyboard)
b) Press the test button on the ultrasound system, the system then wants user ID and password
have to release the test menu. The user ID is customer, which is password
pcg05132, if the system SONOS 7500 still has software status D.1 (presumably
c) In the test menu, select the function "outher test & utilities" with the trackball
d) Then go to "VGA display path test" in the test menu: now it shows
e) For further work with the PC just wants to have this again user ID and password
: the user-ID is always given as default, the password, now on the PC keyboard
to enter is DUNEUSER
Answer the next queries with "yes" and then with "OK"
Return to normal operation of the system with the reset button on the system
test whether 3D goes (as I said, the green light on the PC must be lit), if so, system
Turn off, remove mouse and keyboard, reconnect PC without reconnecting cables
If under point b the password does not work, please call the local service, he can
generate password.
Somewhat awkward, but that was the way many years ago, when the US systems were not
complete
PC's were and one did not come so easily on the operating system level.
This whole procedure is of course also in the service manual, one must search only long, therefore