Академический Документы
Профессиональный Документы
Культура Документы
2. Go to Settings
3. Go to Factory Settings
5. Select YES once “This operation will load default settings and erase all the channels, continue?”
message appears
6. Click the NEXT option until you reach the screen where it will show you the following options
below.
6.3 – Go to Antenna Setup, make sure there is a check mark () on Badr 4/5/6
6.4 – Click the EXIT button on the remote to commence auto configuration on the receiver
8. Select 11938MHz 27500 Ks/s V Change Network Search to YES (with right arrow key) Select
OK to start the Scan.
11. Click the MYHD button on the remote control, and select your subscription channel list
accordingly to view all the channels
CAMBRIDGE 1.0/TRUVIEW 7 MATRIX/GALAXIS 99/G-GUARD
3. “System will be restored to default data. Any data changed will be lost, Continue?” Select OK to
confirm.
7. Click the OK button on the remote control once “Scanning finished. Press OK to save…” message
appears on the TV screen
8. A message on the top portion of the TV screen “saving data, please wait…” will appear
9. Once the message disappears, click the OK button on the remote control
10. Click the right arrow key and look for your subscription channel list named My Arab / My GMA to
view all the channels
DANSAT PREMIUM/ DANSAT PREMIUM 2
3. Select OK and scroll down to FACTORY SETTING and press OK on the remote control.
4. The message ‘This operation will load default and erase all the channels that user added,
continue?’ Select Yes.
7. Select Badr 4/5/6 and other satellites on the Satellite List. Select Blue Key on the RCU for LNB
Setup and select the DiSEqC setting if applicable.
9. Make sure satellite is set to BADR 4/5/6. If not, press the right arrow key and look for BADR 4/5/6
10. Scroll down the list, and select the frequency 11938MHz, 27500Ks/s, V
11. Click the OK button the remote control and set the following:
13. Click the OK option once the “Search End” message appears
14. Click the EXIT button on the remote control to set the TV screen back to full screen mode
16. Click the right arrow key and look for your subscription channel list named My HD / My GMA to
view all the channels
ALTECH HDIR 1
2. Go to Settings
4. Select Yes for the message “Reset settings to Factory Defaults and reboot?”
7. Select your Language, Time Zone, Main TV Output, Resolution, Internet Connection.
8. On the Channel Search Option, Select Arabsat BADR 4/5/6/7- 26.0E and other Satellites connected
to your STB.
9. The STB will detect the DiSEqC for the satellites selected. Select OK and the STB will scan.
10. Once the scan is done, click the Exit button on the remote control to set the TV screen back to
full screen mode
11. Click the OK button on the remote control to view the channel list on the left side of the screen
12. Click the right arrow key on the remote control and look for your subscription channel list named
MyHD / My GMA to view all the channels
My-HD COMPATIBLE HUMAX RECEIVER MODELS
(Includes: HD-Mini, IR3100HD, IR-Eco, IR-Free HD, I-Cord, & etc. /Excludes: IR4000HD)
5. Select Factory Default. Message appears on screen ‘Do you want to reset all values to the factory
default?’ Select YES and type in password 0-0-0-0.
7. Welcome Page – Select Language, Display, Time Zone Select the option Skip to skip the search
and Select Next Select Finish.
9. Search Channels Select Switch Type to LNB Only/ DiSEqC based on your setting.
10. Select Satellite Arabsat/Badr (26.0E) If your setting is DiSEqC then select your settings.
Frequency 11938
Polarisation Vertical
Symbol rate 27500
Transmission DVB
Modulation QPSK
FEC Auto
Select OK.
12. Click the Opt+ button on the remote control and set Network Search ON
Important Note: Please make sure that if any other satellites are active, please go to the
Transponder option of those other satellites, and select NONE to deactivate them temporarily
14. Select the Search option, and click the OK button on the remote control to commence the
scanning process
15. Click the OK (Save) button on the remote control to save the channels scanned
16. Select YES, and the press the OK button on the remote once the “After saving the channels, do
you want to Exit the Installation menu?” message appears
17. Click the OK button on the remote and look for the My-HD channels under TV list, HDTV list, or
ARABSAT/BADR list