Академический Документы
Профессиональный Документы
Культура Документы
kr
() Preliminary Specification
(*) Final Specification
www.DataSheet.co.kr
5 MECHANICAL CHARACTERISTICS
6 INTERNATIONAL STANDARD
7 PACKING
8 PRECAUTION
9 RELIABILITY
D a
Record of Revision
Version Data Page. Items New Description Remark
1.0 2007/07/12 -- First release N/A
www.DataSheet.co.kr
* General Information
Items Specification Unit Note
Active Screen Size 46 inches Diagonal
Display Area 1018.08(H) x 572.67(V) mm
Outline Dimension 1083.0(H) x 627.0(V) x 56.1(D) mm With Balance Board
www.DataSheet.co.kr
Note 2: Maximum Wet-Bulb should be 39°C and no condensation. The relative humidity must not exceed
90% non-condensing at temperatures of 40°C or less. At temperatures greater than 40°C, the wet
bulb temperature must not exceed 39°C.
www.DataSheet.co.kr
Note 3: Sine wave, 11ms, direction: ±x, ±y, ±z (one time each direction)
Note 4: Wave form: random, vibration level: 1.5G RMS, Bandwidth: 10--500Hz
Duration: X, Y, Z 10min (one time each direction)
Voltage
Input High VIH
2.4 -- 3.3 VDC
CMOS Threshold Voltage (High)
Interface Input Low VIL
0 -- 0.7 VDC
Threshold Voltage (Low)
Backlight Power Consumption (ref.) PBL -- 216 -- Watt 2
Life Time 30,000 -- -- Hours 3
The performance of the Lamp in LCD panel, for example life time or brightness, is extremely influenced by
the characteristics of the balance board and I/P board. All the parameters should be carefully designed as
not to produce too much leakage current from high-voltage output. While design or order balance board,
please make sure unwanted lighting caused by the mismatch of the lamp and balance board (no lighting,
flicker, etc) never occurs. After confirmation, the LCD Panel should be operated in the same condition as
installed in your instrument.
Note:
1. VDD=12.0V, fV=60Hz, fCLK=81.5Mhz, 25°C, VDD duration time=470µs, test pattern: full white pattern
2. The backlight power consumption shown above does include loss of external power system at 25°C.
The used lamp current is the lamp typical current IL=6.5mA.
3. The life is determined as the time at which luminance of the lamp is 50% compared to that of initial value
at the typical lamp current on condition of continuous operating at 25±2°C.
4. VCIM=1.25V
VTH
VCIM
VTL
www.DataSheet.co.kr
0V
Vdd
0.9 Vdd
0.1 Vdd
GND
400ms
470µs
Note: (1) All GND (ground) pins should be connected together and should also be connected to the LCD’s
metal frame. (2) All VDD (power input) pins should be connected together. (3) All NC (no connection) pins
should be open without voltage input.
Clock
Rx_0+
R0 G0 R5 R4 R3 R2 R1 R0 G0
Rx_0-
Rx_1+
G1 B1 B0 G5 G4 G3 G2 G1 B1
Rx_1-
Rx_2+
B2 DE VS HS B5 B4 B3 B2 DE
Rx_2-
Rx_3+
R6 NA B7 B6 G7 G6 R7 R6 NA
Rx_3-
(x = O, E)
Clock
Rx_0+
R2 G2 R7 R6 R5 R4 R3 R2 G2
Rx_0-
Rx_1+
G3 B3 B2 G7 G6 G5 G4 G3 B3
Rx_1-
Rx_2+
B4 DE VS HS B7 B6 B5 B4 DE
Rx_2-
Rx_3+
R0 NA B1 B0 G1 G0 R1 R0 NA
Rx_3-
(x = O, E)
Tdisp(v)
Tdisp(h)
Th
Tv
TCLK
www.DataSheet.co.kr
Th
Invalid data
Tblk(h)
Tblk(v)
RGB Data
RGB Data
RGB Data
(EVEN)
(ODD)
(ODD)
CLK
DE
DE
RED(001) 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED ----
RED(254) 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
RED(255) 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
GREEN(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 0 0 0 0 0
GREEN ----
GREEN(254) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0 0
GREEN(255) 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0 0
BLUE(000) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
BLUE(001) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1
BLUE -------
BLUE(254) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 0
BLUE(255) 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1
Values
Parameter Unit
Min. Typ. Max.
t1 0.47 -- 30 ms
www.DataSheet.co.kr
t2 20 -- 100 ms
t3 500 -- -- ms
t4 200 -- -- ms
t5 0 -- 100 ms
t6 0.47 -- 30 ms
t7 300 -- -- ms
Apply the lamp voltage within the LCD operating range. When the backlight turns on before the LCD
operation or the LCD turns off before the backlight turns off, the display may momentarily become abnormal.
Caution: The above on/off sequence should be applied to avoid abnormal function in the display. In case of
handling, make sure to turn off the power when you plug the cable into the input connector or pull the cable
out of the connector.
Specification
o
(Ta=25±5 C, Turn-on after 60mins)
Specification
Item Symbol Unit Note
Min. Typ. Max
HV1/
1 High Voltage (HV) Input -- 750 -- VRMS
HV2
2 Input Current of ech HV IHV -- 60 -- mARMS
3 High Voltage (HV) Output VOUT 720 VRMS
4 Output Lamp Current IOUT 6.0 6.5 7.0 mARMS PWM=90%, 60-torr lamp
5 Operating Frequency FOP 50 55 60 KHz (Recommend)
6 PWM Dimming Frequency FPWM -- 150 -- Hz (Recommend)
7 Dimming Duty Ratio DPWM 20 90 100 % (Recommend)
8 Lamp Type Straight
9 Number of Lamps 24 pcs
Lamp Specification:
14 Output Working Voltage VL (1441) (1550) (1659) VRMS IL=6.5mA
15 Output Current IL 4.0 6.5 (7.0) mARMS
16 Lamp Frequency FLAMP 40 -- 80 KHz
o
-- -- (2360) VRMS Ta=25 C
17 Starting Voltage Vs o
-- -- (2510) VRMS Ta=0 C
D a t a s h e e t p d f
Connector Pin Assignment
CN125: HIROSE_KN30-7P-1.25H
PIN # Symbol Description
1 VCC 12V power supply
2 VFB Lamp current detect signal (full wave current)
3 GND Ground
4 LD1 CCFL connector open & non-lighting signal
5 LD2 CCFL connector open & non-lighting signal
6 LD3 CCFL connector open & non-lighting signal
7 LD4 CCFL connector open & non-lighting signal
SR3 or equivalent
Values
Parameter Symbol Unit Notes
Min. Typ. Max
Contrast Ratio CR 1200 1800 -- 1
2
Surface Luminance (White) LWH 420 500 -- cd/m 2
Luminance Variation δWHITE(9P) -- -- 1.3 3
Response Time (Average) Tγ -- 6.5 -- ms 4, 5 (Gray to Gray)
Rise Time Tr -- 15 -- ms
Decay Time Tf -- www.DataSheet.co.kr
5 -- ms
Color Coordinates
Red Rx 0.660
Ry 0.330
Green Gx 0.206
Gy 0.675
Typ.-0.03 Typ.+0.03
Blue Bx 0.148
By 0.065
White Wx 0.280
Wy 0.280
Viewing Angle (Contrast Ratio>10)
2. Surface Luminance is luminance value at point 5 across the LCD surface 50cm from the surface with all pixels
displaying white. For more information see Fig. 4-2. When lamp current IL=6.5mA, LWH=Lon5, where Lon5 is the
luminance with all pixels displaying white at center 5 location.
V/2 1 2 3
4 5 6 V
7 8 9
V/6
H/6 H/2
www.DataSheet.co.kr
3. The variation in surface luminance, δWHITE(9P) is defined under brightness of IL=6.5mA as:
δWHITE(9P) = Maximum(Lon1, Lon2,…,Lon9)/Minimum(Lon1, Lon2,…Lon9)
4. Response time is the time required for the display to transition from white(L255) to black(L0) (Decay Time,
Tf=TrD), and from black(L0) to white(L255) (Rise Time, Tr=TrR). For additional information see Fig. 4-3.
TrD TrR
L0,15,L31,….L255 L0,15,L31,….L255
100%
90%
Luminance
10%
L0,15,L31,….L255
0%
Time
TrD TrR
6. Viewing angle is the angle at which the contrast ratio is greater than 10. The angles are determined for the
horizontal (or x-axis) and the vertical (or y-axis) with respect to the z-axis which is normal to the LCD surface.
For more information see Fig. 4-5.
www.DataSheet.co.kr
www.DataSheet.co.kr
www.DataSheet.co.kr
www.DataSheet.co.kr
6-2. EMC
(1) ANSI C63.4 “Methods of Measurement of Radio-Noise Emissions from Low-Voltage Electrical and Electrical
Equipment in the Range of 9kHz to 40GHz. “American National standards Institute(ANSI), 1992
(2) C.I.S.P.R “Limits and Methods of Measurement of Radio Interface Characteristics of Information Technology
Equipment.” International Special committee on Radio Interference.
(3) EN 55022 “Limits and Methods of Measurement of Radio Interface Characteristics of Information
www.DataSheet.co.kr
(2) For RoHS compatible products, AUO will add for identification.
Note. The Green Mark will be present only when the green documents have been ready by AUO Internal Green Team.
(The definition of green design follows the AUO green design checklist.)
6-4. EMI
Item Min Typ Max Unit
EMI Level (Note) -- -- -6 dB (µV/m)
SSCG -- 250 -- ps
Module
1pcs Module/ESD Bag
Package information
Carton outside dimension:
1170 x 560 x 690mm
www.DataSheet.co.kr
Cushion set
Cushion top
6pcs Modules
Cushion down
"H" Tape
6pcs / 1 carton
Stretch film
Corner angle
www.DataSheet.co.kr
Pallet
Carton Label
www.DataSheet.co.kr
to attach front/ rear polarizers. Do not use acetone, toluene and alcohol because they cause chemical
damage to the polarizer.
(8) Wipe off saliva or water drops as soon as possible. Their long time contact with polarizer causes
deformations and color fading.
(9) Do not open the case because inside circuits do not have sufficient strength.
8-5 STORAGE
When storing modules as spares for a long time, the following precautions are necessary.
(1) Store them in a dark place. Do not expose the module to sunlight or fluorescent light. Keep the temperature
between 5°C and 35°C at normal humidity.
(2) The polarizer surface should not come in contact with any other object. It is recommended that they be
stored in the container in which they were shipped.
(3) You can remove the glue easily. When the glue remains on the Bezel or its vestige is recognized, please
wipe them off with absorbent cotton waste or other soft material like chamois soaked with normal-hexane.
Waveform: random
Vibration Test Vibration Level: 0.83G RMS
8
(with carton) Bandwidth:10-200Hz
Duration: 30min in each X, Y, Z direction
Height: 31cm
Drop Test
9 1 corner, 3 edges, 6 surfaces
(with carton)
(ASTMD4169-I)